The printout for the type should be just "5xxx", so 512x users won't
wonder why they have a mpc52xx-type UART.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: Fix length handling
n_gsm: Copy n2 over when configuring via ioctl interface
serial: bfin_5xx: grab port lock before making port termios changes
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
serial: bfin_5xx: always include DMA headers
vcs: make proper usage of the poll flags
amiserial: Remove unused variable icount
8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
tty_ldisc: Fix BUG() on hangup
TTY: restore tty_ldisc_wait_idle
SERIAL: blacklist si3052 chip
drivers/serial/bfin_5xx.c: Fix line continuation defects
tty: prevent DOS in the flush_to_ldisc
8250: add support for Kouwell KW-L221N-2
nozomi: Fix warning from the previous TIOCGCOUNT changes
tty: fix warning in synclink driver
tty: Fix formatting in tty.h
tty: the development tree is now done in git
Setting Rx FIFO size to 1 reduces reader process wakeup latency up to
20x for baud rates <= 9600. This patch sets the Rx FIFO size to 1 for
baud rates <= 9600 or if low latency has been requested for the tty.
Signed-off-by: Michael Trimarchi <michael@gandalf.sssup.it>
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Baurzhan Ismagulov <ibr@radix50.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a driver for the serial ports found in VIA and WonderMedia
Systems-on-Chip. Interrupt-driven FIFO operation is implemented.
The hardware also supports pure register-based operation (which is
slower) and DMA-based FIFO operation. As the FIFOs are only 16 bytes
long, DMA operation is probably not worth the hassle.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prototype driver for the IFX6x60 series of SPI attached modems by Jim
Stanley and Russ Gorby
Signed-off-by: Russ Gorby <richardx.r.gorby@intel.com>
[Some reworking and a major cleanup]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port lock exists to protect these resources, so we need to grab it
before making changes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we are using early serial, don't let the normal console rewind
the log buffer, since that causes things to be printed multiple times.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to force a SSYNC here as the LSR register will already
be updated by the time we get back to reading it. This speeds up TX
throughput and lowers general system overhead (since SSYNC is system
wide, not peripheral-specific).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Blackfin systems, peripherals that have optional DMA support always
route their interrupts through the corresponding DMA channel -- even
when DMA is not being used. So in PIO mode, we still need to request
the DMA channel (so interrupts are delivered) which means we need to
always include the DMA header for the DMA defines/functions.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[SERIAL]blacklist si3052 chip
Si3052-based softmodems aren't serial ports so don't bind serial driver to them.
Allows proper driver to bind to them.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the newly exported input_reset_device() call to reset LED state and
mark all keys/buttons as released on all keyboard-like devices when
exiting the debugger.
[jason.wessel@windriver.com: fix compile without keyboard input driver]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Very recently, the RS485 interface has been fixed by adding two further
fields (see commit 1b6331848b).
Check the value of the flag SER_RS485_RTS_BEFORE_SEND before delaying.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb,debug_core: adjust master cpu switch logic against new debug_core locking
debug_core: refactor locking for master/slave cpus
x86,kgdb: remove unnecessary call to kgdb_correct_hw_break()
debug_core: disable hw_breakpoints on all cores in kgdb_cpu_enter()
kdb,kgdb: fix sparse fixups
kdb: Fix oops in kdb_unregister
kdb,ftdump: Remove reference to internal kdb include
kdb: Allow kernel loadable modules to add kdb shell functions
debug_core: stop rcu warnings on kernel resume
debug_core: move all watch dog syncs to a single function
x86,kgdb: fix debugger hw breakpoint test regression in 2.6.35
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
Fix the following sparse warnings:
kdb_main.c:328:5: warning: symbol 'kdbgetu64arg' was not declared. Should it be static?
kgdboc.c:246:12: warning: symbol 'kgdboc_early_init' was not declared. Should it be static?
kgdb.c:652:26: warning: incorrect type in argument 1 (different address spaces)
kgdb.c:652:26: expected void const *ptr
kgdb.c:652:26: got struct perf_event *[noderef] <asn:3>*pev
The one in kgdb.c required the (void * __force) because of the return
code from register_wide_hw_breakpoint looking like:
return (void __percpu __force *)ERR_PTR(err);
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Running a serial console, if too many kernel messages are generated within
a short time causing a lot of serial I/O, the 8250 driver will generate
another kernel message reporting this, which just adds to the I/O. It has
a cascading effect and quickly results the system being brought to its knees
by a flood of "too much work" messages.
Ratelimit the error message to avoid this.
[akpm@linux-foundation.org: use the superior printk_ratelimited()]
[akpm@linux-foundation.org: printk_ratelimited() needs ratelimit.h]
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The actual uart baud rate of devices vary between +/-2% of what is
asked. The SPORT RX sample rate should be faster than double of the
worst case. Otherwise, wrong data may be received. So set SPORT RX
clock to be 3% faster in general.
Reported-by: Olivier STOCK <ostockemer@ereca.fr>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not every platform that has generic legacy 8250 ports manages to have them
clocked the right way or without errata. Provide a generic interface to
allow platforms to override the default behaviour in a manner that dumps
the complexity in *their* code not the 8250 driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The .start_tx callback (imx_start_tx here) isn't only called when the
buffer is non-empty. E.g. after resume or when handshaking is enabled
and the other side starts to signal being ready.
So check for an empty puffer already before sending the first character.
This prevents sending out stale (or uninitialised) data.
Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Andy Green <andy@warmcat.com>
[ukl: reword commit log, put check in while condition]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add more baud rates support referring the baud_table[] defined
in drivers/char/tty_ioctl.c: 3000000/2000000/1000000/500000
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If kzmalloc fails, the uart port is not removed causing a leak.
This patch just add another label that removes the uart when the
kzmalloc fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for platforms to specify custom pm methods.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
port->flags is of type upf_t, which corresponds to UPF_* flags.
ASYNC_BOOT_AUTOCONF is an unsigned integer, which happen to
be the same as UPF_BOOT_AUTOCONF.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes tty name, major and minor numbers. The major number
204 is used across many platform-specific serial drivers, so we
use that.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some controllers implement registers with a stride, to support
those we must implement the proper IO accessors.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes it much easier to integrate the driver with the rest of
the Linux (e.g. MFD subsystem).
The old method is still supported though.
Also, from now on, there is one platform device per port (no
changes are needed for the platform code, as no one registers
the devices anywhere in-tree yet).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Altera UART implementations doesn't route the IRQ line, so we have
to work in polling mode.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Soon we will use that handy function in the altera_uart driver.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loop in wait_for_xmitr() is delaying one extra uS after the ready
condition has been met. Rewrite the loop to only delay if the
transmitter is not ready.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Again basically cut and paste
Convert the main driver set to use the hooks for GICOUNT
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Rosenberg noted that various drivers return the struct with uncleared
fields. Instead of spending forever trying to stomp all the drivers that
get it wrong (and every new driver) do the job in one place.
This first patch adds the needed operations and hooks them up, including
the needed USB midlayer and serial core plumbing.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And while we are at it allow it to fail to find one. Without this the IRQ
option will cause the 3110 driver to fail on 0.7 SFI firmware.
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cleanup for mrst_max3110 includes:
* remove unneeded head files
* make the spi_transfer dma safe, so that driver is more portable
* add more check for error return value
* use mutex_trylock for read thread
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 4547be7 rewrites suspend and resume functions. According
to this rewrite, when a serial port is a printk console device and
can suspend(without set no_console_suspend flag), it will definitely
call set_termios function during its resume, but parameter termios
isn't initialized, this will pass an unpredictable config to the
serial port. If this serial port is not a userspace opened tty device
, a suspend and resume action will make this serial port unusable.
I.E. ttyS0 is a printk console device, ttyS1 or keyboard+display is
userspace tty device, a suspend/resume action will make ttyS0
unusable.
If a serial port is both a printk console device and an opened tty
device, this issue can be overcome because it will call set_termios
again with the correct parameter in the uart_change_speed function.
Refer to the deleted content of commit 4547be7, revert parts relate
to restore settings into parameter termios. It is safe because if
a serial port is a printk console only device, the only meaningful
field in termios is c_cflag and its old config is saved in
uport->cons->cflag, if this port is also an opened tty device,
it will clear uport->cons->cflag in the uart_open and the old config
is saved in tty->termios.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 4547be7 rewrites suspend and resume functions, this
introduces a problem on the OMAP3EVM platoform. when the kernel boots
with no_console_suspend and we suspend the kernel, then resume it,
the serial console will be not usable. This problem should be common
for all platforms.
The cause for this problem is that when enter suspend, if we choose
no_console_suspend, the console_stop will be skiped. But in resume
function, the console port will be set to uninitialized state by
calling set_termios function and the console_start is called without
checking whether the no_console_suspend is set, Now fix it.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONSOLE_POLL support for uartlite enables
KGDB debugging over serial line.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
snprintf() returns the number of bytes which would have been written so
it can be larger than the size of the buffer. In this case it's fine,
but people copy and paste this code so I've fixed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
CONFIG_68328_SERIAL_UART2 doesn't exist in Kconfig, therefore removing
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds UART serial port support for S5P6450 SoC.
The S5P6450 has 6 UARTs, so adds resource of UART4 and UART5.
And to fix membase which is in serial/samsung.c is from Ben Dooks.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
serial_cs doesn't use the system workqueue. Drop spurious
flush_scheduled_work() call.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
"ret" is unsigned, so check for (ret < 0) made no sense.
Made it signed.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
The speed and clock of the serial ports is retrieved from the device
tree in both the PowerPC legacy serial code and the Open Firmware serial
driver, therefore they need to handle the fact that the device tree is
always big endian, while the CPU may not be.
Also fix other device tree references in the legacy serial code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In ioc3uart_probe()
resources were not released during error return path
- ports[phys_port]
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
sparc64 allmodconfig:
drivers/serial/mrst_max3110.c: In function `serial_m3110_startup':
drivers/serial/mrst_max3110.c:470: error: `IRQ_TYPE_EDGE_FALLING' undeclared (first use in this function)
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha allmodconfig:
drivers/serial/mfd.c:144: error: implicit declaration of function 'kzalloc'
drivers/serial/mfd.c:144: warning: assignment makes pointer from integer without a cast
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds driver support for OMAP2/3/4 high speed UART.
The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
What's worse than no comment? A wrong comment.
Several PCMCIA device drivers contained the same comments, which
were based on how the PCMCIA subsystem worked in the old days of 2.4.,
and which were originally part of a "dummy_cs" driver. These comments
no longer matched at all what is happening now, and therefore should
be removed.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Status (CISREG_CCSR) and ExtStatus (CISREG_ESR) registers were
only accessed to enable audio output for some drivers and IRQ for
serial_cs.c. The former also required setting config_req_t.Attributes
to CONF_ENABLE_SPKR; the latter can be simplified to setting this
field to CONF_ENABLE_ESR.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Commit d87d9b7d1 ("tty: serial - fix tty referencing in set_ldisc") changed
set_ldisc to take ldisc number as parameter. This patch fixes AMBA PL010 driver
according the new prototype.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We shouldn't overwrite pre-set values, and we should also
set the port address to the beginning, and not the end of
the 8-port range.
CC: linux-serial@vger.kernel.org
Reported-by: Komuro <komurojun-mbn@nifty.com>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: move probe call to subsys_initcall()
powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
spi/pl022: fix APB pclk power regression on U300
spi/spi_s3c64xx: Warn if PIO transfers time out
spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
spi/s3c64xx: Fix compilation warning
spi/dw_spi: clean the cs_control code
spi/dw_spi: Allow interrupt sharing
spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
spi/spi_s3c64xx: Move to subsys_initcall()
spi: free children in spi_unregister_master, not siblings
gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
of: Fix missing includes - ll_temac
spi/spi_s3c64xx: Staticise non-exported functions
spi/spi_s3c64xx: Make probe more robust against missing board config
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The large cleanup/rewrite of resources in commit ccf68e59e9
accidentally reverted an earlier fix in commit a19e8b2059.
So restore it here.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As copy_*_user() calls access_ok() it should not be called explicitly.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device addresses are usually printed in hex.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'merge-devicetree' of git://git.secretlab.ca/git/linux-2.6:
spi.h: missing kernel-doc notation, please fix
of: fix missing headers for of_address_to_resource() in MTD and SysACE drivers
of: Fix missing includes
ata: update for of_device to platform_device replacement
microblaze: Fix of: eliminate of_device->node and dev_archdata->{of,prom}_node
microblaze: Fix of/address: Merge all of the bus translation code
booting-without-of: Remove nonexistent chapters from TOC, fix numbering
This patch fixes missing includes from a number of .c files because
the code (wrongfully) depended on prom.h including them. The include
of linux/of_address.h was removed in microblaze prom.h in commit
"of/address: Clean up function declarations" (sha1 id 22ae782f8), but
not fixed in some callers. This patch fixes them up.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
If a video head and keyboard are hooked up, specifying "console=ttyS0"
or similar to use a serial console will not work properly.
The key issue is that we must register all serial console capable
devices with register_console(), otherwise the command line specified
device won't be found. The sun serial drivers would only register
themselves as console devices if the OpenFirmware specified console
device node matched. To fix this part we now unconditionally get
the serial console register by setting serial_drv->cons always.
Secondarily we must not add_preferred_console() using the firmware
provided console setting if the user gaven an override on the kernel
command line using "console=" The "primary framebuffer" matching
logic was always triggering o n openfirmware device node match, make
it not when a command line override was given.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
UART Features extract from STEricsson U6715 data-sheet (arm926 SoC for mobile phone):
* Fully compatible with industry standard 16C550 and 16C450 from various
manufacturers
* RX and TX 64 byte FIFO reduces CPU interrupts
* Full double buffering
* Modem control signals include CTS, RTS, (and DSR, DTR on UART1 only)
* Automatic baud rate selection
* Manual or automatic RTS/CTS smart hardware flow control
* Programmable serial characteristics:
– Baud rate generation (50 to 3.25M baud)
– 5, 6, 7 or 8-bit characters
– Even, odd or no-parity bit generation and detection
– 1, 1.5 or 2 stop bit generation
* Independent control of transmit, receive, line status, data set interrupts and FIFOs
* Full status-reporting capabilities
* Separate DMA signaling for RX and TX
* Timed interrupt to spread receive interrupt on known duration
* DMA time-out interrupt to allow detection of end of reception
* Carkit pulse coding and decoding compliant with USB carkit control interface [40]
In 16550A auto-configuration, if the fifo size is 64 then it's an U6 16550A port
Add set_termios hook & export serial8250_do_set_termios to change uart
clock following baudrate
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of the way gpiolib works we actually need to ifdef this in our
header file
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox