We don't want to swap bytes that we're reading and writing to the
FIFOs when we're running on a big-endian CPU. Doing so causes
problems like where the qcom-spmi-iadc driver can't detect the
type of device because the bytes are all mixed up. Use the raw IO
accessors for these API instead, and collapse pmic_arb_base_read()
into the byte reading API so that we aren't tempted to read non-FIFO
data like commands with that function.
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get notified immediately when a balloon target is set, instead of waiting for
up to one second.
The up-to 1 second gap could be long enough to cause swapping inside of the
VM that receives the VM.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Tested-by: Siva Sankar Reddy B <sankars@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the behavior of the first start of the balloon and a reset. Also on
unload, declare that the balloon driver does not have any capabilities
anymore.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2m ballooning significantly reduces the hypervisor side (and guest side)
overhead of ballooning and unballooning.
hypervisor only:
balloon unballoon
4 KB 2 GB/s 2.6 GB/s
2 MB 54 GB/s 767 GB/s
Use 2 MB pages as the hypervisor is alwys 64bit and 2 MB is the smallest
supported super-page size.
The code has to run on older versions of ESX and old balloon drivers run on
newer version of ESX. Hence match the capabilities with the host before 2m
page ballooning could be enabled.
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VMware's hypervisor requests a VM to reclaim memory this is preferrably done
via ballooning. If the balloon driver does not return memory fast enough, more
drastic methods, such as hypervisor-level swapping are needed. These other methods
cause performance issues, e.g. hypervisor-level swapping requires the hypervisor to
swap in a page syncronously while the virtual CPU is blocked.
Hence it is in the interest of the VM to balloon memory as fast as possible. The
problem with doing this is that the VM might end up doing nothing else than
ballooning and the user might notice that the VM is stalled, esp. when the VM has
only a single virtual CPU.
This is less of a problem if the VM and the hypervisor perform balloon operations
faster. Also the balloon driver yields regularly, hence on a single virtual CPU
the Linux scheduler should be able to properly time-slice between ballooning and
other tasks.
Testing Done: quickly ballooned a lot of pages while wathing if there are any
perceived hickups (periods of non-responsiveness) in the execution of the
linux VM. No such hickups were seen.
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps with debugging vmw_balloon behavior, as it is clear what
functionality is enabled.
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of waiting for the next GET_TARGET command, we can react faster
by exploiting the fact that each hypervisor call also returns the
balloon target.
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Philip P. Moltmann <moltmann@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new capability to the driver that allow sending 512 pages in
one hypervisor call. This reduce the cost of the driver when reclaiming
memory.
Signed-off-by: Xavier Deguillard <xdeguillard@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Philip P. Moltmann <moltmann@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kzalloc() fails then gms is NULL and we are returning NULL, but the
functions which called this function gru_register_mmu_notifier() are not
expecting NULL as the return. They are expecting either a valid pointer
or the error code in ERR_PTR.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the function tfh_restart() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be future-proof and for better readability the time comparisons are
modified to use time_before() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the SCIF kernel node QP control messages required to
enable SCIF RMAs. Examples of such node QP control messages include
registration, unregistration, remote memory allocation requests,
remote memory unmap and SCIF remote fence requests.
The patch also updates the SCIF driver with minor changes required to
enable SCIF RMAs by adding the new files to the build, initializing
RMA specific information during SCIF endpoint creation, reserving SCIF
DMA channels, initializing SCIF RMA specific global data structures,
adding the IOCTL hooks required for SCIF RMAs and updating RMA
specific debugfs hooks.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the fence APIs required to synchronize
DMAs. SCIF provides an interface to return a "mark" for all DMAs
programmed at the instant the API was called. Users can then "wait" on
the mark provided previously by blocking inside the kernel. Upon
receipt of a DMA completion interrupt the waiting thread is woken
up. There is also an interface to signal DMA completion by polling for
a location to be updated via a "signal" cookie to avoid the interrupt
overhead in the mark/wait interface. SCIF allows programming fences on
both the local and the remote node for both the mark/wait or the fence
signal APIs.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF allows users to read from or write to registered remote memory
via CPU copies or DMA. The API verifies that both local and remote
windows are valid before initiating the CPU or DMA transfers. SCIF has
optimized algorithms for handling byte aligned as well as cache line
aligned DMA engines. A registration cache is maintained to avoid the
overhead of pinning pages repeatedly if buffers are reused. The
registration cache is invalidated upon receipt of MMU notifier
callbacks. SCIF windows are destroyed and the pages are unpinned only
once all prior DMAs initiated using that window are drained. Users can
request synchronous DMA operations as well as tail byte ordering if
required. CPU copies are always performed synchronously.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the SCIF mmap/munmap interface. A similar
capability is provided to kernel clients via the
scif_get_pages()/scif_put_pages() APIs. The SCIF mmap interface
queries to check if a window is valid and then remaps the local
virtual address to the remote physical pages. These mappings are
subsequently destroyed upon receipt of the VMA close operation or
scif_get_pages(). This functionality allows SCIF users to directly
access remote memory without any driver interaction once the mappings
are created thereby providing bare-metal PCIe latency. These mappings
are zapped to avoid RMA accesses from user space, if a Coprocessor is
reset.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the implementation for operations performed on the
list of SCIF windows. Examples of such operations includes adding the
windows to the list of registered (or cached) windows, querying the
list of self or remote windows and unregistering windows. The query
operation is used by SCIF APIs which initiate DMAs, CPU copies or
fences to ensure that a window remains valid during a transfer.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implements the SCIF APIs required to pin and unpin
pages. SCIF registration locks down the pages. It then sends a remote
window allocation request to the peer. Once the peer has allocated
memory, the local SCIF endpoint copies the pinned page information to
the peer and notifies the peer once the copy has complete. The peer
upon receipt of the registration notification adds the new remote
window to its list. At this point the window page information is
available on both self and remote nodes so that they can start
performing SCIF DMAs, CPU copies and fences. The unregistration API
tears down the registration at both self and remote nodes.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the internal data structures required to perform SCIF
RMAs. The data structures required to maintain per SCIF endpoint, RMA
information are contained in scif_endpt_rma_info. scif_pinned_pages
describes a set of SCIF pinned pages maintained locally. The
scif_window is a data structure which contains all the fields required
to describe a SCIF registered window on self and remote nodes. It
contains an offset which is used as a key to perform SCIF DMAs and CPU
copies between self and remote registered windows.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the SCIF header file and IOCTL interface with the
changes required to support RMAs. APIs added include the ability to
pin pages and register those pages with SCIF. SCIF kernel clients can
also add references to remote registered pages and access them via the
CPU. The user space IOCTL interface has been updated to enable SCIF
registration, RDMA/CPU copies and fence APIs for RDMA synchronization.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the MIC host daemon to work with corresponding
changes in COSM. Other MIC daemon fixes, cleanups and enhancements as
are also rolled into this patch. Changes to MIC sysfs ABI which go
into effect with this patch are also documented.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since card side COSM functionality, to trigger MIC device shutdowns
and communicate shutdown status to the host, is now moved into a
separate COSM client driver, this patch removes this functionality
from the base MIC card driver. The mic_bus driver is also updated to
use the device index provided by COSM rather than maintain its own
device index.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since COSM functionality is now moved into a separate COSM driver
drivers, this patch removes this functionality from the base MIC host
driver. The MIC host driver now implements cosm_hw_ops and registers a
COSM device which allows the COSM driver to trigger
boot/shutdown/reset of the MIC devices via the cosm_hw_ops.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The COSM client driver running on the MIC cards is implemented as a
kernel mode SCIF client. It responds to a "shutdown" message from the
host by triggering a card shutdown and also communicates the shutdown
or reboot status back the host. It is also responsible for syncing the
card time to that of the host. Because SCIF messaging cannot be used
in a panic context, the COSM client driver also periodically sends a
heartbeat SCIF message to the host thereby enabling the host to detect
card crashes.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The COSM driver communicates with the MIC cards over SCIF. A SCIF
"server" listens for incoming connections from "client" MIC cards as
they boot. After the connection is accepted a separate work item is
scheduled for each MIC card. This work item normally stays blocked in
scif_poll but wakes up to process messages from the card.
The SCIF connection between the host and card COSM components is used
to (a) send the command to shut down the card (b) receive shutdown
status back from the card upon completion of shutdown (c) receive
periodic heartbeat messages to detect card crashes (d) send host time
to the card to enable the card to sync its time to the host.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The COSM driver allows boot, shutdown and reset of Intel MIC devices
via sysfs. This functionality was previously present in the Intel MIC
host driver but has now been taken out into a separate driver so that
it can be shared between multiple generations of Intel MIC products.
The sysfs kernel ABI used by the COSM driver is the same as that
defined originally for the MIC host driver in
Documentation/ABI/testing/sysfs-class-mic.txt.
The COSM driver also contains support for dumping the MIC card log_buf
and doing a "force reset" for the card via debugfs. The OSPM support
present in the MIC host driver has now largely been moved to user
space and only a small required OSPM functionality is now present in
the driver.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIC COSM bus allows the co-processor state management (COSM)
functionality to be shared between multiple generations of Intel MIC
products. The COSM driver registers itself on the COSM bus. The base
PCIe drivers implement the bus ops and register COSM devices on the
bus, resulting in the COSM driver being probed with the COSM devices.
COSM bus ops, e.g. start, stop, ready, reset, therefore abstract out
common functionality from its specific implementation for individual
generations of MIC products.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for registration/de-registration of kernel mode SCIF
clients. SCIF clients are probed with new and existing SCIF peer
devices. Similarly the client remove method is called when SCIF
peer devices are removed.
Changes to SCIF peer device framework necessitated by supporting
kernel mode SCIF clients are also included in this patch.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIF poll allows both user and kernel mode clients to wait on
events on a SCIF endpoint. These events include availability of
space or data in the SCIF ring buffer, availability of connection
requests on a listening endpoint and completion of connections
when using async connects.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIC X100 DMA engine has a special status descriptor which writes
an 8 byte value to a destination location. This is used to signal
completion of all DMA descriptors prior to the status descriptor.
This patch add a new DMA engine API which enables updating a
destination address with an 8 byte immediate data value.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Lawrynowicz, Jacek <jacek.lawrynowicz@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Siva Yerramreddy <yshivakrishna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iova is a library which can be built without IOMMU_SUPPORT
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iova library has use outside the intel-iommu driver, thus make it a
module.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to separate intel-iommu from the iova library.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes maintainer's email address from
hp.com to hpe.com in hpilo.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: David Altobelli <david.altobelli@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add minimum and maximum value of module parameter
max_ccb in hpilo.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some SoC specified values store in eFuse,
such as the cpu_leakage and cpu_version,
this driver can expose these values to /sys base on nvmem.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch brings read-only support for the On-Chip OTP cells
in the i.MX23 and i.MX28 processor. The driver implements the
new NVMEM provider API.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the devicetree bindings for the Freescale MXS On Chip
OTP driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver handles the i.MX On-Chip OTP Controller found in
i.MX6Q/D, i.MX6S/DL, i.MX6SL, and i.MX6SX SoCs. Currently it
just returns the values stored in the shadow registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds support for the On Chip One Time Programmable Peripheral
(OCOTP) on the Vybrid platform.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd