The ieee80211softmac_call_events function, when called with event type
IEEE80211SOFTMAC_EVENT_ASSOCIATE_TIMEOUT should pass the network as the
third parameter. This patch does that.
Signed-off-by: Joseph Jezak <josejx@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses the "No queue exists" messages commonly seen during
authentication and associating. These appear due to scheduling multiple
authentication attempts on the same network. To prevent this, I added a
flag to stop multiple authentication attempts by the association layer.
I also added a check to the wx handler to see if we're connecting to a
different network than the one already in progress. This scenario was
causing multiple requests on the same network because the network BSSID
was not being updated despite the fact that the ESSID changed.
Signed-off-by: Joseph Jezak <josejx@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I recently patched softmac to enable shared key authentication. This small patch
will enable crazy or unfortunate bcm43xx users to use this new capability.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit ba9b28d19a, routine
ieee80211softmac_capabilities was added to ieee80211softmac_io.c. As
denoted by its name, it completes the capabilities IE that is
needed in the associate and reassociate requests sent to the
AP. For at least one AP, the Linksys WRT54G V5, the capabilities
field must set the 'short preamble' bit or the AP refuses to
associate. In the commit noted above, there is a call to the
new routine from ieee80211softmac_reassoc_req, but not from
ieee80211softmac_assoc_req. This patch fixes that oversight.
As noted in the subject, v2.6.17 is affected. My bcm43xx card had been
unable to associate since I was forced to buy a new AP. I finally was
able to get a packet dump and traced the problem to the capabilities
info. Although I had heard that a patch was "floating around", I had
not seen it before 2.6.17 was released. As this bug does not affect
security and I seem to have the only AP affected by it, there should
be no problem in leaving it for 2.6.18.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes coverity id #913. ieee80211_monitor_rx() passes the skb
to netif_rx() and we should not reference it any longer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should preallocate IV+ICV space when encrypting the frame.
Currently no problem shows up just because dev_alloc_skb aligns the
data len to SMP_CACHE_BYTES which can be used for ICV.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use Softmac-suggested TX ratecode:
ieee80211softmac_suggest_txrate()
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds device IDs for Symbol LA-4123 and Global Sun Tech
GL24110P to the HostAP PLX driver.
This is not tested with real hardware, but there is no reason why it
shouldn't work.
Please test.
Signed-off-by: Faidon Liambotis <faidon@cube.gr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- const-ify pci_device_id table
- clean up pci_device_id table with PCI_DEVICE()
- don't store internal pointer in pci_device_id table,
use pci_device_id::driver_data as an integer index
- use dev_printk() for messages where eth%d prefix is unavailable
- formatting fixes
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Becker-derived drivers often have the 'io_size' member in their chip
info struct, indicating the minimum required size of the I/O resource
(usually a PCI BAR). For many situations, this number is either
constant or irrelevant (due to pci_iomap convenience behavior).
This change removes the io_size invariant member, and replaces it with a
compile-time constant.
Drivers updated: fealnx, gt96100eth, winbond-840, yellowfin
Additionally,
- gt96100eth: unused 'drv_flags' removed from gt96100eth
- winbond-840: unused struct match_info removed
- winbond-840: mark pci_id_tbl[] const, __devinitdata
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code. These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.
Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9". These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.
Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Remove in-source changelog, it's in the global kernel history.
- convert silly and useless version to useful one
- replace invariant pci_id_tbl[]::io_size uses with EPIC_TOTAL_SIZE
- remove now-unused io_size member from pci_id_tbl[]
- current kernel style prefers dev_printk() for the rare ethernet driver
messages that cannot print an 'eth%d' prefix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
Move workqueue exports to where the functions are defined.
[CPUFREQ] Misc cleanups in ondemand.
[CPUFREQ] Make ondemand sampling per CPU and remove the mutex usage in sampling path.
[CPUFREQ] Add queue_delayed_work_on() interface for workqueues.
[CPUFREQ] Remove slowdown from ondemand sampling path.
There is a code sequence where the locking is substream->self_group.lock
-> ins->scbs[index].lock
substream->self_group.lock is interrupt safe, and taken from irq context
as well (trace is snipped for brevity)
so what can happen is
cpu 0 cpu 1
user context user context
take ins->scbs[index].lock without disabling interrupts
get substream->self_group.lock (irqsafe)
try to get ins->scbs[index].lock (spins)
interrupt happens
try to get substream->self_group.lock (spins)
which is an obvious AB-BA deadlock
fix is to just take the lock with _irqsafe
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca: initialize send and receive queue locks separately
lockdep identifies a lock by the call site of its initialization. By
initializing the send and receive queue locks in mthca_wq_init() we confuse
lockdep. It warns that that the ordered acquiry of both locks in
mthca_modify_qp() is recursive acquiry of one lock:
=============================================
[ INFO: possible recursive locking detected ]
---------------------------------------------
modprobe/1192 is trying to acquire lock:
(&wq->lock){....}, at: [<f892b4db>] mthca_modify_qp+0x60/0xa7b [ib_mthca]
but task is already holding lock:
(&wq->lock){....}, at: [<f892b4ce>] mthca_modify_qp+0x53/0xa7b [ib_mthca]
Initializing the locks separately in mthca_alloc_qp_common() stops the
warning and will let lockdep enforce proper ordering on paths that acquire
both locks.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found a bug in memory hot-add code for ia64.
IA64's code has copies of pgdat's array on each node to reduce memory
access over crossing node. This array is used by NODE_DATA() macro. When
new node is hot-added, this pgdat's array should be updated and copied on
new node too.
However, I used for_each_online_node() in scatter_node_data() to copy
it. This meant its array is not copied on new node.
Because initialization of structures for new node was halfway,
so online_node_map couldn't be set at this time.
To copy arrays on new node, I changed it to check value of pgdat_list[]
which is source array of copies. I tested this patch with my Memory Hotadd
emulation on Tiger4. This patch is for 2.6.17-git20.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
Jiri reports that the stop_machin kthread conversion caused his machine to
hang when suspending. Hyperthreading is apparently involved.
I don't see why that would be and I can't reproduce it. Revert to the 2.6.17
code.
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With recent change, if CONFIG_HOTPLUG_CPU is disabled,
register_cpu_notifier() is not exported. And it breaked moduler msr/cpuid
(msr.c was already fixed).
We need to use register_hotcpu_notifier() now in module, instead of
register_cpu_notifier().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the module parameter disable_cfc which can be used to
disable the credit based flow control. The credit based flow control
was introduced with the Bluetooth 1.1 specification and devices can
negotiate its support, but for testing purpose it is helpful to allow
disabling of it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is a small cleanup of the L2CAP source code. It makes some
coding style changes and moves some functions around to avoid forward
declarations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the Bluetooth class devices into real devices. The
Bluetooth class is kept and the driver core provides the appropriate
symlinks for backward compatibility.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a generic Bluetooth platform device that can be used
as parent device by virtual and serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces the automatic sniff mode feature. This allows
the host to switch idle connections into sniff mode to safe power.
Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the suspend/resume methods for the HCI USB
driver by killing all outstanding URBs on suspend, and re-issuing
them on resume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Frontline sniffer device looks like a normal H:2 Bluetooth device,
but it is not and so mark it as raw mode device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix for inability of br_dump_ifinfo to handle non-zero start index:
loop index never increases when entered with non-zero start.
Spotted by Kirill Korotaev.
Signed-off-by: Andrey Savochkin <saw@swsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in drivers/dma/:
- use correct function & parameter names
- add descriptions where omitted
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joseph Jezak