The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".
This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.
Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch documents the qca8k's reset-gpios property that
can be used if the QCA8337N ends up in a bad state during
reset.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gateway validation does not need a dst_entry, it only needs the fib
entry to validate the gateway resolution and egress device. So,
convert ip6_nh_lookup_table from ip6_pol_route to fib6_table_lookup
and ip6_route_check_nh to use fib6_lookup over rt6_lookup.
ip6_pol_route is a call to fib6_table_lookup and if successful a call
to fib6_select_path. From there the exception cache is searched for an
entry or a dst_entry is created to return to the caller. The exception
entry is not relevant for gateway validation, so what matters are the
calls to fib6_table_lookup and then fib6_select_path.
Similarly, rt6_lookup can be replaced with a call to fib6_lookup with
RT6_LOOKUP_F_IFACE set in flags. Again, the exception cache search is
not relevant, only the lookup with path selection. The primary difference
in the lookup paths is the use of rt6_select with fib6_lookup versus
rt6_device_match with rt6_lookup. When you remove complexities in the
rt6_select path, e.g.,
1. saddr is not set for gateway validation, so RT6_LOOKUP_F_HAS_SADDR
is not relevant
2. rt6_check_neigh is not called so that removes the RT6_NUD_FAIL_DO_RR
return and round-robin logic.
the code paths are believed to be equivalent for the given use case -
validate the gateway and optionally given the device. Furthermore, it
aligns the validation with onlink code path and the lookup path actually
used for rx and tx.
Adjust the users, ip6_route_check_nh_onlink and ip6_route_check_nh to
handle a fib6_info vs a rt6_info when performing validation checks.
Existing selftests fib-onlink-tests.sh and fib_tests.sh are used to
verify the changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
FDB, VLAN and PTP fixes for SJA1105 DSA
This patchset is an assortment of fixes for the net-next version of the
sja1105 DSA driver:
- Avoid a kernel panic when the driver fails to probe or unregisters
- Finish Arnd Bermann's idea of compiling PTP support as part of the
main DSA driver and not separately
- Better handling of initial port-based VLAN as well as VLANs for
dsa_8021q FDB entries
- Fix address learning for the SJA1105 P/Q/R/S family
- Make static FDB entries persistent across switch resets
- Fix reporting of statically-added FDB entries in 'bridge fdb show'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).
However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database. After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".
In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).
Fixes: 93647594d8 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 8456721dd4 ("net: dsa: sja1105: Add support for
configuring address ageing time"), we started to reset the switch rather
often (each time the bridge core changes the ageing time on a switch
port).
The unfortunate reality is that SJA1105 doesn't have any {cold, warm,
whatever} reset mode in which it accepts a new configuration stream
without flushing the FDB. Instead, in its world, the FDB *is* an
optional part of the static configuration.
So we play its game, and do what we also do for VLANs: for each 'bridge
fdb' command, we add the FDB entry through the dynamic interface, and we
append the in-kernel static config memory with info that we're going to
use later, when the next reset command is going to be issued.
The result is that 'bridge fdb' commands are now persistent (dynamically
learned entries are lost, but that's ok).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the commit 1da7382134 ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.
SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:
Specify the maximum number of MAC address dynamically learned from
the respective port. It is used to limit the number of learned MAC
addresses per port.
It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.
For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1da7382134 ("net: dsa: sja1105: Add FDB operations for
P/Q/R/S series"), these bits were set in the static config, but
apparently they did not do anything. The reason is that the packing
accessors for them were part of a patch I forgot to send.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.
The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:
8021q: adding VLAN 0 to HW filter on device swp2
So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnd Bergmann pointed out in commit 78fe8a28fb ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.
So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut says:
====================
net: dsa: microchip: Convert to regmap
This patchset converts KSZ9477 switch driver to regmap.
This was tested with extra patches on KSZ8795. This was also tested
on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
====================
Signed-off-by: Marek Vasut <marex@denx.de>
Regmap provides bit manipulation functions to set/clear bits, use those
insted of reimplementing them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The regmap config tables are rather similar for various generations of
the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating
those tables without duplication. Note that $regalign parameter is not
used right now, but will be used in KSZ87xx series switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver now uses regmap , get rid of ad-hoc ksz_io_ops
abstraction, which no longer has any meaning. Moreover, since regmap
has it's own locking, get rid of the register access mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic SPI regmap support into the driver.
Previous patches unconver that ksz_spi_write() is always ever called
with len = 1, 2 or 4. We can thus drop the if (len > SPI_TX_BUF_LEN)
check and we can also drop the allocation of the txbuf which is part
of the driver data and wastes 256 bytes for no reason. Regmap covers
the whole thing now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code which sends out the register read/write opcodes
to the switch, since the code differs in single bit between read and
write.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirect function call to dev->dev_ops->get_port_addr() is expensive
especially if called for every single register access, and only returns
the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used by the KSZ9477 code, move them from
the header into that code. Note that these functions will be soon
replaced by regmap equivalents.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions in the header file are static, and the header file is
included from single C file, just inline the code into the C file.
The bonus is that it's easier to spot further content to clean up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: implement vlan offloads
This patchset introduces hardware VLAN offload support and also does some
maintenance: we replace driver version with uts version string, add
documentation file for atlantic driver, and update maintainers
adding Igor as a maintainer.
v3: shuffle doc sections, per Andrew's comments
v2: updates in doc, gpl spdx tag cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
set_features should update flags and reinit hardware if
vlan offload settings were changed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update datapath by adding logic related to hardware assisted
vlan strip/insert behaviour.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating features and vlan_features with vlan HW offload.
Added vlan_tag fields to rx/tx ring_buff to track vlan related data.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register declaration macros required to work with vlan offload mode.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed some files had -or-later, however overall driver has
-only license. Clean this up.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia is resposible now for all new features and bugfixes.
Reflect that in MAINTAINERS.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document contains configuration options description,
details and examples of driver various settings.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it was discussed some time previously, driver is better to
report kernel version string, as it in a best way identifies
the codebase.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-26
This series contains updates to ixgbe and i40e only.
Mauro S. M. Rodrigues update the ixgbe driver to handle transceivers who
comply with SFF-8472 but do not implement the Digital Diagnostic
Monitoring (DOM) interface. Update the driver to check the necessary
bits to see if DOM is implemented before trying to read the additional
256 bytes in the EEPROM for DOM data.
Young Xiao fixes a potential divide by zero issue in ixgbe driver.
Aleksandr fixes i40e to recognize 2.5 and 5.0 GbE link speeds so that it
is not reported as "Unknown bps". Fixes the driver to read the firmware
LLDP agent status during DCB initialization, and to properly log the
LLDP agent status to help with debugging when DCB fails to initialize.
Martyna fixes i40e for the missing supported and advertised link modes
information in ethtool.
Jake fixes a function header comment that was incorrect for a PTP
function in i40e.
Maciej fixes an issue for i40e when a XDP program is loaded the
descriptor count gets reset to the default value, resolve the issue by
making the current descriptor count persistent across resets.
Alice corrects a copyright date which she found to be incorrect.
Piotr adds a log entry when the traffic class 0 is added or deleted, which
was not being logged previously.
Gustavo A. R. Silva updates i40e to use struct_size() where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2019-06-27
please apply another round of qeth updates for net-next.
This completes the conversion of the control path to use dynamically
allocated cmd buffers, along with some fine-tuning for the route
validation fix that recently went into -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As follow-up to commit 0cd6783d3c ("s390/qeth: check dst entry before use"),
consolidate the dst_check() logic into a single helper and add a wrapper
around the cast type selection.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_gro_receive() to pass up all types of packets that a L3 device
may receive.
1) For proper L2 packets received by the IQD sniffer, this is the
obvious thing to do.
2) For af_iucv (which doesn't provide a GRO assist), the GRO code will
transparently fall back to netif_receive_skb(). So there's no need to
special-case this traffic in our code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply some cleanups to qeth_snmp_command() and its callback:
1. when accessing the user data, use the proper struct instead of
hard-coded offsets. Also copy the request data straight into the
allocated cmd, skipping the extra memdup_user() to a tmp buffer.
2. capping the request length is no longer needed, the same check gets
applied at a base level in qeth_alloc_cmd().
3. clean up some duplicated (and misindented) trace statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base MPC cmds are the last remaining user of the static cmd buffers.
Port them over to use dynamic allocation, and stop backing the write
channel's cmd buffers with pages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new wrapper that allocates DIAG cmds of the right size, and fills
in the common fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code that uses qeth_send_simple_setassparms_prot(), we currently
can't differentiate whether the cmd should contain (1) no parameter, or
(2) a 4-byte parameter with value 0.
At the moment this doesn't cause any trouble. But when using dynamically
allocated cmds, we need to know whether to allocate & transmit an
additional 4 bytes of zeroes.
So instead of the raw parameter value, pass a parameter pointer
(or NULL) to qeth_send_simple_setassparms_prot().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common steps when releasing an accepted or unaccepted socket.
Move this code into a common routine.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: ipv4: fix circular-list infinite loop
Tariq and Ran reported a regression caused by net-next commit
2638eb8b50 ("net: ipv4: provide __rcu annotation for ifa_list").
This happens when net.ipv4.conf.$dev.promote_secondaries sysctl is
enabled -- we can arrange for ifa->next to point at ifa, so next
process that tries to walk the list loops forever.
Fix this and extend rtnetlink.sh with a small test case for this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter