The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:
a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right
b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of adding hooks inside stmmac_platform it is better to just use
the standard PM callbacks within the specific dwmac-driver. This only
used by the dwmac-rk driver.
This reverts commit cecbc5563a ("stmmac: allow to split suspend/resume
from init/exit callbacks").
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 88f8b1bb41.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.
After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.
For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As dwmac-* drivers that need OF match have been converted
to use their own internal OF match data structure this can
now be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these fields are unused and has been unused since they
were added 3 and 5 years ago. Drop them since they are clearly
not very useful.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.
This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the tx-fifo-depth and rx-fifo-depth from the devicetree. The Synopsys
stmmac controller fifos are configurable per product instance, and the fifo
sizes are needed to configure certain features correctly such as flow control.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the macros to be used for MDC clock selection. The MDC clock
frequency is based on scaled system clock, and has to be confined to a range
of 1-2.5 MHz. Based on the input CSR clock, the scaling factor has to be
selected.
The platform specific code will provide the default value of this scaling
factor, based on the input CSR clock.
There is an option to set MDC clock higher than the IEEE 802.3 specified
frequency limit of 2.5 MHz. This applies for the interfacing chips that
support higher MDC clocks. The resultant higher clock of 12.5 MHz requires
additional Macros to be defined for the clock divider corresponding to the
to the following selection.
-----------------------------------------
Selection MDC Clock
-----------------------------------------
1000 clk_csr_i/4
1001 clk_csr_i/6
1010 clk_csr_i/8
1011 clk_csr_i/10
1100 clk_csr_i/12
1101 clk_csr_i/14
1110 clk_csr_i/16
1111 clk_csr_i/18
This support has to be added both in the include file, as well as driver. The
driver need to program the registers based on the interfacing chips. This would
be more board specific information and needs to be passed through the platform
code to the driver. This work would be carried out in the future patch set
release.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch explicitly defines the CSUM offload engine type which need
(not mandatory) to be passed from the platform code.
STMMAC core supports two check sum offload engine types- Type-1 & Type-2.
Also, there are STMMAC cores that do not have the check sum offload
capabilities.
The behaviour of Type-1 & Type-2 cores related to provision of checksum
increases the packet length for Type-1 cores by 2, as the checksum is appended
at the end of data packet and the same is made accountable in the DMA status.
The STMMAC cores beyond Version-3.5 provide HW interface registers which allows
the user to read the HW capabilities, while to support the previous cores the
information related to HW capabilities has to be provided from the platform
code.
The Type-1 cores which do not have the HW register interface need this
information.
This patch also updates the driver's doc.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stmmac mdio bus name prefix is hardcoded in the driver, this allows
only phys on stmmac mdio buses to connect, however stmmac should allow
phys on other mdio buses too.
This patch adds new variable phy_bus_name to plat_stmmacenet_data
struct to let the BSP decide which phy bus to be used by stmmac driver.
A typical use-case is to have generic MDIO buses like mdio-gpio on top
of stmmac.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, most PHY configuration parameters were passed
into the STMMAC device as a separate PHY device. As well as being
unusual, this made it difficult to make changes to the MAC/PHY
relationship.
This patch moves all the PHY parameters into the MAC configuration
structure, mainly as a separate structure. This allows us to completely
ignore the MDIO bus attached to a stmmac if desired, and not create
the PHY bus. It also allows the stmmac driver to use a different PHY
from the one it is connected to, for example a fixed PHY or bit banging
PHY.
Also derive the stmmac/PHY connection type (MII/RMII etc) from the
mode can be passed into <platf>_configure_ethernet.
STLinux kernel at git://git.stlinux.com/stm/linux-sh4-2.6.32.y.git
provides several examples how to use this new infrastructure (that
actually is easier to maintain and clearer).
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new field 'force_sf_dma_mode' to plat_stmmacenet_data
struct to allow users to specify if they want to use force store forward
eventhough tx_coe is not available in hw.
without this flag stmmac driver will use cut-thru mode not use
store-forward mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the plat_stmmacenet_data
the init and exit callbacks that can be used
for invoking specific platform functions.
For example, on ST targets, these call the
PAD manager functions to set PIO lines and
syscfg registers.
The patch removes the stmmac_claim_resource
only used on STM Kernels as well.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first version of the driver had hard-coded the logic
for handling the checksum offloading.
This was designed according to the chips included in
the STM platforms where:
o MAC10/100 supports no COE at all.
o GMAC fully supports RX/TX COE.
This is not good for other chip configurations where,
for example, the mac10/100 supports the tx csum in HW
or when the GMAC has no IPC.
Thanks to Johannes Stezenbach; he provided me a first
draft of this patch that only reviewed the IPC for the
GMAC devices.
This patch also helps on SPEAr platforms where the
MAC10/100 can perform the TX csum in HW.
Thanks to Deepak SIKRI for his support on this.
In the end, GMAC devices for STM platforms have
a bugged Jumbo frame support that needs to have
the Tx COE disabled for oversized frames (due to
limited buffer sizes). This information is also
passed through the driver's platform structure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Deepak SIKRI <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the CSR Clock range selection.
Original patch from Johannes Stezenbach fixed the CSR
in the stmmac_mdio. We agreed to provide this through
the platform instead of.
Also thanks to Johannes for having tested it on ARM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids unnecessary casting and adds the ioaddr in the
private structure.
This patch also removes many warning when compile the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new enh_desc is used for selecting the enhanced descriptors
structure. There are several scenarios; some chips (mac10/100
or gmac) want to use the enhanced descriptors; others want the normal
ones.
For example, on ST platforms: MAC10/100 uses the normal desc structure
and the GMAC uses the enhanced one.
It can be useful to get this information from the platform.
This could also be decided at run-time looking at the chip's ID number;
but it could happen that chips with the same ID want to use different
descriptor structure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin