dwc2_core_reset() was previously renamed to
dwc2_core_reset_and_dr_force_mode(). Now add back dwc2_core_reset() which
performs only a basic core reset without forcing the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Renamed dwc2_core_reset() to dwc2_core_reset_and_force_dr_mode(). This
describes what it is doing more accurately. This is in preparation of
introducing a plain dwc2_core_reset() function that only performs the
reset and doesn't force the mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In (usb: dwc2: reset dwc2 core before dwc2_get_hwparams()) we added an
extra reset to the probe path for the dwc2 USB controllers. This
allowed proper detection of parameters even if the firmware had already
used the USB part.
Unfortunately, this extra reset is quite slow and is affecting boot
speed. We can avoid the double-reset by skipping the extra reset that
would happen just after the one we added. Logic that explains why this
is safe:
* As of the CL mentioned above, we now always call dwc2_core_reset() in
dwc2_driver_probe() before dwc2_hcd_init().
* The only caller of dwc2_hcd_init() is dwc2_driver_probe(), so we're
guaranteed that dwc2_core_reset() was called before dwc2_hdc_init().
* dwc2_hdc_init() is the only caller that passes an irq other than -1 to
dwc2_core_init(). Thus if dwc2_core_init() is called with an irq
other than -1 we're guaranteed that dwc2_core_reset was called before
dwc2_core_init().
...this allows us to remove the dwc2_core_reset() in dwc2_core_init() if
irq is not < 0.
Note that since "irq" wasn't used in the function dwc2_core_init()
anyway and since select_phy was always set at exactly the same times we
could avoid the reset, we remove "irq" and rename "select_phy" to
"initial_setup" and adjust the callers accordingly.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.
Specifically, the observed order is:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.
We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted. We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.
Notes:
1. As part of this change we add a "force" parameter to
dwc2_hcd_disconnect() so that when we're unloading the module we
avoid the new behavior. The need for this was pointed out by John
Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
exactly the same bit of code from dwc2_port_intr(). To avoid
duplication, we refactor that code out into a new function
dwc2_hcd_connect().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.
Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8c4 ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB OTG driver in isochronous mode has to set the parity of the receiving
microframe. The parity is set to even by default. This causes problems for
an audio gadget, if the host starts transmitting on odd microframes.
This fix uses Incomplete Periodic Transfer interrupt to toggle between
even and odd parity until the Transfer Complete interrupt is received.
Signed-off-by: Roman Bacik <rbacik@broadcom.com>
Reviewed-by: Abhinav Ratna <aratna@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a 200ms guard period to avoid unnecessary resets of the dwc2
ip. This delay sometimes prove to be too large when usbcv is run with
an ehci host. dwc2 only needs to be reset after addressed state.
Change the logic to reset ip after addressed state.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register backup function can be called from atomic context. Instead
of using atomic memory pool, embed backup storage space in
struct dwc2_hsotg.
Also add a valid flag in each struct as NULL pointer can't be used as
the content validity check any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2 may not be able to exit from hibernation if the hardware
does not provide a way to detect resume signalling in this state.
Thus, add the possibility to disable hibernation feature.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.
Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow controller to enter in hibernation during usb bus suspend and
inform both phy and gadget about the suspended state.
While in hibernation, the controller can't detect the resume condition.
An external mechanism must call usb_phy_set_suspend on resume.
Exit hibernation when controller gets the resume interrupt and inform
only gadget driver about it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When suspending usb bus, phy driver may disable controller power.
In this case, registers need to be saved on suspend and restored
on resume.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dump all registers to take a complete snapshot of dwc2 state.
Code is inspired by dwc3/debugfs.c
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prepare to add more debug code. Moreover, don't save dentry * for
each file in struct dwc2_hsotg as clean up is done with
debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed
altogether for the same reason.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These members are only occupying space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Suspend/resume code assumed that the gadget was always started and
enabled to connect to usb bus. This means that the actual state of the
gadget (started/stopped or connected/disconnected) was not correctly
preserved on suspend/resume cycle. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds mutex, which protects initialization and
deinitialization procedures against suspend/resume methods. This mutex
will be needed by the updated suspend/resume calls, which tracks gadget
state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a call to s3c_hsotg_disconnect() from 'end session'
interrupt (GOTGINT_SES_END_DET) to correctly notify gadget subsystem
about unplugged usb cable. DISCONNINT interrupt cannot be used for this
purpose, because it is asserted only in host mode.
To avoid reporting disconnect event more than once, a disconnect call has
been moved from USB_REQ_SET_ADDRESS handling function to SESSREQINT
interrupt. This way driver ensures that disconnect event is reported
either when usb cable is unplugged or every time the host starts a new
session. To handle devices which has been synthesized without
SRP support, connected state is set in ENUMDONE interrupt.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds the gadget data structure and appropriate data structure pointers
to the common dwc2_hsotg data structure. To keep the driver data
dereference code looking clean, the gadget variable declares are only available
for peripheral and dual-role mode. This is needed so that the dwc2_hsotg data
structure can be used by the hcd and gadget drivers.
Updates gadget.c to use the dwc2_hsotg data structure and gadget pointers
that have been moved into the common dwc2_hsotg structure.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The unioned u32 is used for clearing etc. Having the number of
bitfield bits add up to more than 32 is broken, even if benign.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.
Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.
It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the "dr_mode", the otg controller can work as
device role and host role. Some boards always want to use host mode
and some other boards want to use gadget mode. We use the dts setting
to set dwc2's mode, rather than fixing it to whatever hardware says.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the data structures that are in the s3c-hsotg
source into core.h. This is a necessary step towards unifying
the s3c-hsotg and dwc2 into a single DRD.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb,fb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[ pz - Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC2 driver should now be in good enough shape to move out of
staging. I have stress tested it overnight on RPI running mass
storage and Ethernet transfers in parallel, and for several days
on our proprietary PCI-based platform.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John Youn