While normal Dual and Quad SPI Transfers are unidirectional, we must do
a bidirectional transfer if loopback mode is enabled, else rx_buf is not
filled.
With spidev it seemed to work, as spidev uses the same buffer for
tranmission and reception.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If spi_master.cleanup() is not needed, it can be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
List full example compatible properties with soctypes instead of just the
soctypes, so checkpatch can validate DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_wait_for_interrupt() unconditionally enables interrupts, even when the
wait condition is already satisfied. This causes a high interrupt load (2
interrupts/byte for full-duplex Single SPI transfers, 1 interrupt/byte for
RSPI with TX Only mode, or QSPI in unidirectional Dual or Quad Transfer
mode).
Change this to return immediately when the wait condition is satisfied.
This dramatically reduces the interrupt load, especially in high-speed
Quad Transfer mode, and increases transfer speed, as no interrupts need to
be handled when there's space available in the output FIFO, or data
available in the input FIFO.
Benchmark results for QSPI on r8a7791 while reading 1 MiB from 30 MHz SPI
FLASH on the Koelsch development board:
Before:
Single SPI Dual SPI Quad SPI
Interrupts: 2096856 1048592 1048594
Mbps: 0.9 1.6 1.6
After:
Single SPI Dual SPI Quad SPI
Interrupts: 1048569 21295 8
Mbps: 0.7 10.8 12.9
I don't know why Single SPI slowed down a bit.
I've also verified functionality for RSPI-RZ on r7s72100, but don't have
benchmark results as there's no SPI FLASH connected to RSPI on the Genmai
development board. Unlike RSPI and QSPI, RSPI-RZ has separate interrupts
for RX and TX, which shows that Single SPI transfers now generate (mostly)
RX interrupts, as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes an issue that the following build error happens when
the CONFIG_OF is not set:
drivers/spi/spi-rspi.c: In function 'rspi_probe':
drivers/spi/spi-rspi.c:1203:26: error: 'rspi_of_match' undeclared (first use in this function)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Quad and Dual SPI Transfers on the Renesas Quad Serial
Peripheral Interface, as found in R-Car Gen2 SoCs like R-Car H2 (r8a7790)
and R-Car M2 (r8a7791):
- Add unidirectional transfer methods for Quad/Dual SPI Transfers.
- Program the sequencer to handle SPI messages with multiple transfer
modes when Quad or Dual transfers are enabled for an SPI slave.
Up to 4 transfer modes per SPI message are supported by the hardware.
- Advertise the availability of Quad and Dual SPI modes on QSPI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's only one RSPI/QSPI clock, so we can use NULL as the clock ID
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get the driver ready for the migration to the common clock framework by
calling clk_prepare_enable() and clk_disable_unprepare().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying loopback mode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the RSPI variant in the RZ/A1H (r7s72100) SoC.
Main differences with RSPI on SH are:
- Lack of TX only mode, hence we always have to use full duplex
transfers,
- The Data Register must be accessed used 8-bit operations.
RSPI on RZ is matched using the new "rspi-rz" platform device name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for multiple interrupts, based on the SDK reference code.
This is needed for RZ/A1H, which supports 3 interrupts.
When using multiple interrupts, they must be called "rx" (SPRI) and "tx"
(SPTI). The error interrupt (SPEI) is not used, as it matters for slave
mode only.
When using a single interrupt, it may be called "mux". If it cannot be
found, the first interrupt in the device's resources will be used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
qspi_send_pio() and qspi_receive_pio() are very similar: they both send
and receive full duplex data to/from the hardware, but ignore the data
stream in the unused direction.
Merge them into qspi_transfer_out_in(), now supporting real full duplex.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_pio() and rspi_receive_pio() are very similar:
- the former only sends data, using TX Only Mode,
- the latter sends and receives full duplex data to/from the hardware,
but uses dummy transmit data.
Merge them into rspi_transfer_out_in(), now supporting full duplex if
needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Split off qspi_transfer_one() (which doesn't support DMA yet) from
rspi_transfer_one().
Replace the abstraction of send_pio()/receive_pio() by the abstracrion of
transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helpers rspi_data_{out,in,out_in}() to write, read, or write and
read data to/from the Data Register, taking care of waiting until data
or space is available in the buffers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add rspi_{write,read}_data(), to abstract 8-bit (QSPI, and RSPI on RZ/A1H)
versus 16-bit (RSPI) Data Register access.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the generic SPI core handle SPI messages, calling into our
rspi_transfer_one() method.
rspi_assert_ssl() and rspi_negate_ssl() are absorbed into
rspi_prepare_message() and rspi_unprepare_message(), as they actually
enable/disable the whole SPI function, instead of just (de)asserting the
chip select line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The documentation for spi_master.set_cs() says:
assert or deassert chip select, true to assert
i.e. its "enable" parameter uses assertion-level logic.
This does not match the implementation of spi_set_cs(), which calls
spi_master.set_cs() with the wanted logic level of the chip select line,
which depends on the polarity of the chip select signal.
Correct the documentation to match the implementation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove the bits_per_word checking in sc18is602_check_transfer() and
let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation in spi_setup() already set spi->bits_per_word = 8 when
spi->bits_per_word is 0 before calling spi->master->setup.
So we don't need to do it again in setup() callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warning:
drivers/spi/spi-pxa2xx.c:1270:12: warning: ‘pxa2xx_spi_suspend’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for specifying the SPI clock phase and polarity, based on the
SDK reference code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
converted the driver to use ACPI provided DMA helpers but it forgot to
initialize the platform data for the channels to -1. Failing to do so will
result inadvertent match in the filter function because 0 is a valid
channel number.
Prevent this from happening by initializing both platform data channels
correctly to -1.
Fixes: cddb339bad (spi/pxa2xx: convert to dma_request_slave_channel_compat())
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
On ARM-based SHMOBILE, the rspi driver builds and works fine without the
DMA controller driver, hence relax the dependencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have a spi_sh_clear_bit() function, there's no reason not to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Rephrase the comments about tx/rx_nbits validity checks,
- Remove the stale comment about SPI_3WIRE (the code it refers to was
removed in commit 368ca4e0c7 ("spi:
Eliminate 3WIRE spi_transfer check")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Geert Uytterhoeven