This NULL pointer dereference is observed during suspend resume
stress test. All pending commands are cancelled when system goes
into suspend state. There a corner case in which host may receive
response for last scan command after this and try to trigger extra
active scan for hidden SSIDs.
The issue is fixed by adding a NULL check to skip that extra scan.
Fixes: 2375fa2b36 (mwifiex: fix unable to connect hidden SSID..)
Cc: <stable@vger.kernel.org> [v4.2+]
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current TDLS implementation always includes ht/vht information
in tdls setup confirm frame which causes teardown by legacy
peer station after TDLS handshake. We will inclue ht/vht
capabilities in tdls setup confirm frame only if peer station
supports it to fix this problem.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cfg80211_inform_bss would return null in some cases, such as
memory allocation failure.
This patch adds sanity check for this case, to avoid possible
issues when above corner case is hit.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
64k Tx and Rx buffers are allocated during driver initialization
for SDIO level data aggregations. When host is under memory
pressure situation, kzalloc() request for 64k may fail.
We will try allocating 32k buffers and disable our rx single port
aggreagation feature in this situation.
If the allocation still fails, we will disable our sdio multport
aggregation feature as well. In this way, we will transmit and
receive packets one by one, thus reduce the demand for big
memory.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch includes below changes
1) Check if multiport aggregation feature flag while doing rx
length validation check.
2) Reset buffer size variables when buffers are freed.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the issue of delay time in A-MSDU tx packet.
In generated new A-MSDU packet, the time stamp is initialized to zero.
Choose the time of first MSDU packet as aggregated packet's time.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interface counters should be incremented in add_virtual_intf()
and decremented in del_virtual_intf() function. This patch
corrects it.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align fields reg_ch_conf_last and reg_ch_conf_pending of
struct wl1271{} to 64bit.
Without this, on 64bit ARM, wlcore_set_pending_regdomain_ch() fails at
the point it calls set_bit(ch_bit_idx, (long*)wl->reg_ch_conf_pending);
Here is the error message while doing iw wlan0 scan or connect:
[ 10.666857] wlcore: IRQ work
[ 10.670046] wlcore: intr: 0x40 (fw_rx_counter = 1, drv_rx_counter = 0, tx_results_counter = 0)
[ 10.678697] wlcore: WL1271_ACX_INTR_DATA
[ 10.682810] Unhandled fault: alignment fault (0x96000021) at 0xffffffc037a817f4
[ 10.690139] Internal error: : 96000021 [#1] PREEMPT SMP
[ 10.695366] Modules linked in:
[ 10.698437] CPU: 3 PID: 894 Comm: irq/60-wl18xx Tainted: G W 4.2.0-rc6-linaro-hikey #2
[ 10.707501] Hardware name: HiKey Development Board (DT)
[ 10.712733] task: ffffffc03a9d1680 ti: ffffffc039e18000 task.ti: ffffffc039e18000
[ 10.720239] PC is at set_bit+0x14/0x30
[ 10.724002] LR is at wlcore_set_pending_regdomain_ch+0x40/0x4c
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The patch adds support for "outside the context of a BSS"(OCB) mode
to ath9k driver and extends debugfs files by OCB ralated information.
This patch was tested on AR9380-AL1A cards.
Signed-off-by: Jan Kaisrlik <kaisrja1@fel.cvut.cz>
Cc: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix rssi calculation error which was introduced in otus to ar9170
porting.
Signed-off-by: Hiroaki KAWAI <hiroaki.kawai@gmail.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mwifiex_dbg macro has two tests that could be consolidated
into a function reducing overall object size ~10KB (~4%).
So convert the macro into a function.
$ size drivers/net/wireless/mwifiex/built-in.o* (x86-64 defconfig)
text data bss dec hex filename
233102 8628 4809 246539 3c30b drivers/net/wireless/mwifiex/built-in.o.new
243949 8628 4809 257386 3ed6a drivers/net/wireless/mwifiex/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIE type devices are being FW reloaded without being properly
reset then the device ends up in a locked state, requiring the
device to be completely powered down. This patch adds a reset
through watchdog at the moment the device (cores) has been
recognized. This will solve warm reboot issues.
Cc: Rafal Milecki <zajec5@gmail.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of error during brcmf_bus_start() the network interfaces were
freed using free_netdev(). However, the interfaces may have additional
memory allocated which is not freed. The netdev has destructor set to
brcmf_cfg80211_free_netdev() which frees the additional memory if
allocated and call free_netdev(). The brcmf_net_detach() either calls
brcmf_cfg80211_free_netdev() directly or uses unregister_netdev() when
struct net_device::reg_state indicates the netdev was registered.
Reported-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of passing ifidx and drvr just pass struct brcmf_if pointer
which holds both parameters.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_fws_txstatus_suppressed() function prototype specifies an
ifidx parameter which is not used within the function implementation.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both PCIe and SDIO devices have the possibility to log the firmware
console output in kernel log. For PCIe it is logged when PCIE debug
level is enabled. For SDIO it is logged when user specifies a non-zero
console interval through debugfs. This patch tries to make it a
bit more consistent. The firmware console output is only logged when
FWCON debug level is enabled.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because the P2P Device interface in firmware uses the same interface
index as the primary interface we use the bsscfg index as index in the
struct brcmf_pub::iflist. However, in the data path we get the interface
index and not the bsscfg index. So we need a mapping of interface index
to bsscfg index, which can be determined upon handle adding the interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most call sites of brcmf_txfinalize already have struct brcmf_if
instance so pass that to brcmf_txfinalize() as the function
needs it anyway.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The knowledge on how to map the interface index to a struct brcmf_if
instance is in brcmf_get_ifp() so use that function when only the
interface index is known instead of accessing brcmf_pub::iflist
directly.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The p2pdev interface is setup in firmware resulting in a interface
event. This event has role and no-if flag. When role is p2p client
and no-if flag is set it indicates that this is the p2pdev interface.
This info is used in handling the event and adding interface in the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Just pass the interface to be removed, ie. the struct brcmf_if instance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid spreading the ifidx in the driver, but have it return the
struct brcmf_if instance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rx path the firmware provide an interface index which is used to
map to a struct brcmf_if instance. However, this involves some trick
that is done in two places. This is changed by having driver core
providing brcmf_get_ifp() function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of qca99x0 and MSI-X supported/enabled we
failed during interrupts registering with message:
ath10k_pci 0000:04:00.0: failed to request MSI-X ce irq 50: -22
Issue/fix was reproduced/tested using Dell Latitude E6430 laptop.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ldpc is not configured for fixed rates. This blocks auto rate vs fixed
rate performance comparison. Since firmware is considering ldpc vdev
param for fixed rate selection, it has to be configured to enable ldpc
for fixed rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
PRI value is used as divider when DFS detector analyzes candidate
radar pulses.
If PRI deviation is big from its origin PRI, DFS detector could miss
valid radar reports since HW often misses detecting radar pulses and
causes long interval value of pulses.
For instance from practical results, if runtime PRI is calculated as
1431 for fixed PRI value of 1428 and delta timestamp logs 15719,
the modular remainder will be 1409 and the delta between the remainder
and runtime PRI is 22 that is bigger than PRI tolerance which is 16.
As a result this radar report will be ignored even though it's valid.
By using spec defined PRI for fixed PRI, we can correct this error.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of pulses per burst on Japan chirp radar is
between 1 and 3. The previous value, 20, is representing
number of bursts, but since current DFS detector is using
pulse detection other than bursts, use the pulse number
for correct radar detection.
Also using the highest number helps to avoid false detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* fix signedness in beacon statistics;
* deinline some functions to reduce size when device tracing is enabled;
* filter beacons out in AP mode when no stations are associated;
* deprecate firmwares version -12;
* fix a runtime PM vs. legacy suspend race;
* one-liner fix for a ToF bug;
* clean-ups in the rx code;
* small debugging improvement;
* fix WoWLAN with new firmware versions;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XkqB
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* some debugfs improvements;
* fix signedness in beacon statistics;
* deinline some functions to reduce size when device tracing is enabled;
* filter beacons out in AP mode when no stations are associated;
* deprecate firmwares version -12;
* fix a runtime PM vs. legacy suspend race;
* one-liner fix for a ToF bug;
* clean-ups in the rx code;
* small debugging improvement;
* fix WoWLAN with new firmware versions;
Some platforms really don't like DMA bursts of 256 bytes, and this
causes the firmware to crash when sending beacons.
Also, changing this based on the firmware version does not seem to make
much sense, so use 128 bytes for all versions.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
OpenWrt user reported b43 doesn't probe wireless core on SoC BCM5356A1:
[ 0.000000] bcma: bus0: Found chip with id 0x5356, rev 0x01 and package 0x04
it is because this chip uses different 802.11 core revison than others:
[ 0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x15, class 0x0)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brand: Airlive (Ovislink Corp.)
Name: Turbo-G USB Adaptor
Model: WT-2000USB
USB ID: 1b75:3070
Reported-and-tested-by: Michael Coates <michlinux@hotmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The genl_notify function has too many arguments for no real reason - all
callers use genl_info to get them anyway. Just pass the genl_info down to
genl_notify.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thresholds uses -1 to indicate that default value should be used.
Since thresholds are unsigned sign checking makes no sense.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thresholds uses -1 to indicate that default value should be used.
Since thresholds are unsigned sign checking makes no sense.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid underflows signed variables should be used in expression.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unsigned minus constant is still unsigned so checking its sign makes no
sense.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were never used in the tree, and are marked as reserved
in the IEEE 802.11 documentation (ANA).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.
Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the driver can never configure the data here, this field
will always be reported as 0 by the firmware. Even if this was
not the case, however, it wouldn't matter since the extra data
would be added beyond the end of the phy_info structure we use
in the driver, so wouldn't harm anything in this code either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This message is useless - it's in the good case that always
happens so enabling it doesn't really help. Just remove it.
There are other ways to debug this (e.g. tracing) so there's
no need to add a message in the bad case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's possible for an AP interface to be UP but not actually
operating (i.e. not beaconing etc.) - in this case it can't
actually do ToF, so check for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag is set in all supported firmwares.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
This flag is set in all supported firmwares.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firmwares have this flag set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firmwares use the new API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
All the supported firwmares support the new API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current kernel support only one fw name with theoretically only one
fw version located in “firmware/htc_[9271|7010].fw”. Which is ok so far we
have only one fw version (1.3). After we realised new fw 1.4, we faced
compatibility problem which was decided to solve by firmware name and
location:
- new firmware is located now in
firmware/ath9k_htc/htc_[9271|7010]-1.4.0.fw
- old version 1.3 should be on old place, so old kernel have no issues
with it.
- new kernels including this patch should be able to try different
supported (min..max) fw version.
- new kernel should be able to support old fw location too. At least for
now.
At same time this patch will add new module option which should allow user
to play with development fw version without replacing stable one. If user
will set “ath9k_htc use_dev_fw=1” module will try to find
firmware/ath9k_htc/htc_[9271|7010]-1.dev.0.fw first and if it fails, use
stable version: for example...1.4.0.fw.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was missed in the original commit adding the flag and ath10k only printed "bit10":
ath10k_pci 0000:02:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70.6-2 api 3
htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,bit10
Also add a build test to avoid this happening again.
Fixes: ccec9038c7 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vdevs associated with a given chanctx should be
restarted if the bandwidth changes. Otherwise
traffic may cease.
This is known to fix STA CSA with bandwidths wider
than 20MHz.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary to make vdev restarting logic
reusable later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The remain_on_channel callback needs different
timeout. Calling ieee80211_queue_work() with a
shorter delay after calling it with a longer delay
will not change the timer. This caused the
offchannel timeout worker to not trigger in time
and caused the device to stay on channel longer
then expected. This could cause some problems and
was be easily reproduced with `iw offchannel`
command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for mesh to ath10k. We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.
Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode. As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true. The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.
When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:
ip link set wlan0 down
iw dev wlan0 set type mp
ip link set wlan0 up
iw dev wlan0 set freq 5745 80 5775
iw dev wlan0 mesh join mesh-vht
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the case of raw mode without nohwcrypt parameter, we
should still make sure the frame is protected before
adding MIC_LEN to avoid skb_under_panic errors.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, ath10k restricts received frames to those matching BSSID.
When other BSS frames are requested (e.g. in mesh mode), add an internal
monitor device so those frames are not filtered.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes hardware reports invalid mcs index in rx descriptor
when operating in VHT80 mode and all packets with invalid mcs
will be eventually dropped in mac80211. This issue is observerd during
testing on QCA99X0 chipsets.
This patch adds a warn message for dumping the rx desc info which helps
in analysing the issue when invalid mcs is received.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to the VHT STS, this is supposed to be propagated by firmware.
In case it's not, use the default value, but as last resort.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The VHT STS CAP shall be reported by firmware to host, like in case of
QCA99x0. For QCA6174 hw family this isn't set for some reason.
So for this particular chips, let's assume it has the ability to
support VHT NDP in up to 4 STSs (which is true by the way).
Change the published beamformee STS cap accordingly to 3 or to what
the firmware reports.
Assumption so far, it suppose to be the num_rf_chains-1, was
completely wrong.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.
Fix this by limiting the probe responses when the specified
threshold limit is reached.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.
To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.
Failure happens with the following stack trace
[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MU-MIMO Rx involves different interpretation of
the VHT-SIG-A compared to SU-MIMO.
The incorrect interpretation led ath10k to report
VHT MCS values greater than 9 which subsequently
prompted mac80211 to drop such frames. This
effectively broke Rx with MU-MIMO in many cases
and manifested with a kernel warning in the log
which looked like this:
[ 14.552520] WARNING: CPU: 2 PID: 0 at net/mac80211/rx.c:3578 ieee80211_rx+0x26c/0x940 [mac80211]()
[ 14.552522] Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
... call trace follows ...
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
We don't support firmwares that don't use the new API.
This also allows to use all the SCD queues, so increase
the reported number of queues to 31.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
-13.ucode has been published long ago. Deprecate old
versions of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
There's obviously no reason to write a NUL-terminating byte into
the debugfs file. Apparently nobody tried to use this from a tool
that doesn't strip NUL bytes though, so we never noticed. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
If we are in d0i3 when entering suspend, we leave d0i3 so that
mac80211 can call us to remove connections or whatever before going to
suspend. We do this by calling pm_runtime_resume() early in the slave
transport flow and reactivating it later, when the wiphy suspend flow
runs.
The problem is that we queue a work in order to leave d0i3. If this
work hasn't run yet when the wiphy suspend flow is called, we have a
race and entering d0i3 fails (because we're still holding the
IWL_MVM_REF_EXIT_WORK reference).
To solve this, simply flush the d0i3_exit_work at the beginning of the
iwl_mvm_suspend() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
When in AP mode, we need beacons from other APs for HT protection.
However, when there's no any associated station we will not do
any Tx and thus don't really need beacons. On the other hand, these
beacons will cause a lot of unnecessary wakeups which increase our
power consumption. Handle this by asking FW to pass beacons only when
there's at least one associated station.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
With CONFIG_IWLWIFI_DEVICE_TRACING=y, these functions are rather large,
too big for inlining.
With this .config: http://busybox.net/~vda/kernel_config,
after uninlining these functions have sizes and callsite counts
as follows:
iwl_read32 475 bytes, 51 callsites
iwl_write32 477 bytes, 90 callsites
iwl_write8 493 bytes, 3 callsites
Reduction in size is about 74,000 bytes:
text data bss dec hex filename
90758147 17226024 36659200 144643371 89f152b vmlinux0
90687995 17221928 36659200 144569123 89df323 vmlinux.after
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
ECHO_CMD is a simple command that can be sent to the
firmware just to check that it is alive.
This command is useful for debug purpose, provide a debugfs
hook to send it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
When receiving statistics notification there is a field of average energy.
This is defines as signed 8 bit, while FW refers to it as unsigned.
when the energy is higher than 127 this causes in iwl_mvm_stat_iterator
a wrong computation of the signal
int sig = -stats->general.beacon_filter_average_energy;
resulting in incorrect CQM event (change from low to high).
While at it - update the rest of the fields to the correct type.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
This debugfs entry was implemented just as a proof-of-concept before
the full support for netdetect via cfg80211/mac80211 was implemented.
Now that we have a proper way to enable netdetect from userspace, this
entry is redundant and should be removed to avoid unnecessary
maintenance work.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67 ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.
Fixes: e04cafbc38 ("ath10k: fix peer limit enforcement")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 5d5cd85ff4 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff4 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak")
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host platforms such as routers supported by OpenWRT can
support NVRAM reading directly from internal NVRAM store.
With this patch the nvram load routines will fall back to
this method when there is no nvram file and support is
available in the kernel.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The event mask length is determined by the highest event number
that is specified in the driver. When this length is shorter than
firmware expects setting event mask will fail and device becomes
pretty useless. This issue was reported with bcm4339 firmware that
was recently released.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_flowring_block blocks the last active flowring under the same
interface instead of the one provided by caller. This could lead to a
dead lock of netif stop if there are more than one flowring under the
interface and the traffic is high enough so brcmf_flowring_enqueue can
not unblock the ring right away.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cfg80211_check_combinations() so we can bail out early when an
interface add or change results in an invalid combination.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Expose ring buffer read/write pointers and other useful statistics
through debugfs.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The interface combination provided by brcmfmac did not truly reflect
the combinations supported by driver and/or firmware.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcom is working on better reflection of interface combinations. With
upcoming patches we may have 1st combination supporting less interfaces
than others.
To don't run out of addresses check all combinations to find the one
with the greatest max_interfaces value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
current code will handle -ETIMEDOUT as success which is probalbly wrong.
According to this comment I assume it is safe to handle -ETIMEDOUT as false:
drivers/net/wireless/ath/ath9k/calib.c
290 /*
291 * We timed out waiting for the noisefloor to load, probably due to an
292 * in-progress rx. Simply return here and allow the load plenty of time
293 * to complete before the next calibration interval. We need to avoid
294 * trying to load -50 (which happens below) while the previous load is
295 * still in progress as this can cause rx deafness. Instead by returning
296 * here, the baseband nf cal will just be capped by our present
297 * noisefloor until the next calibration timer.
298 */
Since no other error wariants are present, this patch is checking only
for (ret <= 0).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2eAA
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-23' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
Add support for the new (bigger) TX power command. This doesn't
actually take advantage of the new capabilities (to set per-chain
TX power limits) but makes the code compatible with newer firmware
images expecting the larger command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
split long debug messages that may result warning in tracing.
Fixes: 1a84e77160 ("iwlwifi: mvm: add debug info to schedule scan complete message.")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The command string array is assumed to be indexable by a full u8, so it
must have 256 entries (0-255), not just 255. A recent firmware change
(apparently) started using the command 0xff for a notification to the
host, causing the driver to crash in debug message/tracing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when waking from d0i3 there is a wakeup reason.
Enum in driver is not up to date with FW api - fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
My static checker complains that we don't check for underflows in
iwl_dbgfs_fw_dbg_conf_write(). This is harmless because we have a
sanity check in iwl_mvm_start_fw_dbg_conf(), but we may as well make
this unsigned and silence the underflow warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJV1FziAAoJEG4XJFUm622bEJwH/RdNlAK4+IS9Tx0K6EA2fDE3
001J16in/1IPPr8/RmQWNzHGN5/GAYlAdl5v4fkwb8qvcDCyPlQbSEC8ghd32H6M
G1101qEfGk9bhLTpI8xjeqsT1gl98LswPYNAfoRX4AJKAmNCkfJ1WILLi/Q2DUOf
oG6IersuqQOdQbkXDnMm49FBZeSkVvzsJL+WQhKhYblh0bDH3qGuLcYvtkSnt+P8
8QG5X+DPEpmaYcu+5E5N0XgffsdPj/+xXlFova4DFySDYb4OzEH1MYp/rHjPpnUo
nDJqxZIgkkmhu0CGtvpWNeSZ7GQBI0Bzdd+dwBY5yyg5AqWuQ5A1W+4r3SjvHyU=
=A8Ax
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in code that's one
byte larger (for me), but reduces struct link_ant and struct link
size by the two unsigned long values that store the parameters each.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces code size slightly (at least on x86/64) while also
removing memory consumption by two unsigned long values for each
ath5k device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If .pull_fw_stats() fails for some reason while processing
fw stats event, collected pdev/vdev/peer stats just before
the failure should be freed. This is unlikely to happen,
just code review catch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found incorrect sequence in ath10k_core_stop() where wmi pktlog
disable cmd is passed from ath10k_debug_stop() to firmware
immediately after wmi pdev suspend cmd. Firmware will not accept
any wmi cmd after receiving wmi pdev suspend cmd.
Fix this issue in ath10k_core_stop() by moving ath10k_debug_stop()
just before sending pdev suspend cmd. So that pktlog disable cmd
will get passed before pdev suspend cmd.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9i6F
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-18' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
When we enter D0i3, we must stop TXing otherwise the
sequence number we use might conflict with the firmware's
internal TX. In order to do so, we have
IWL_MVM_STATUS_IN_D0I3 which should prevent any Tx while we
enter D0i3. There is a bug in this code since we may Tx even
if IWL_MVM_STATUS_IN_D0I3 is set. This can happen as long as
mvm->d0i3_ap_sta_id is not set.
To make sure that we don't have any packet in the Tx path
while we set mvm->d0i3_ap_sta_id, call synchronize_net only
after we already set mvm->d0i3_ap_sta_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently if we wake up during D0I3 due to beacon loss we disconnect
immediately. This behaviour causes redundant disconnection, which could
be prevented by polling as it is usually done in mac80211.
Instead, we prefer reporting beacon loss and let mac80211 try polling
before disconnection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
KASan error report:
==================================================================
BUG: KASan: out of bounds access in iwl_init_sband_channels+0x207/0x260 [iwlwifi] at addr ffff8800c2d0aac8
Read of size 4 by task modprobe/329
==================================================================
Both loops of this function compare data from the 'chan' array and then
check if the index is valid.
The 2 conditions should be inverted to avoid an out-of-bounds access.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix bug where MIMO is disabled for low latency TX on P2P VIF
regardless of configuration. Make it dependent on
IWL_MVM_RS_DISABLE_P2P_MIMO compilation option. Change configuration
so that MIMO will be disabled only in SDIO platforms.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MAC/BB name is"????" if the MAC/BB is unknown.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add diversity statistics and sync the driver
statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync the driver statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2500usb_validate_eeprom() read data up to 0x6e (EEPROM_CALIBRATE_OFFSET)
but only 0x6a bytes has been allocated and read from the eeprom.
This lead to out-of-bound accesses and invalid values for
EEPROM_BBPTUNE_R17 and EEPROM_CALIBRATE_OFFSET.
Change the EEPROM_SIZE to 0x6e in order to retrieve all the fields.
Tested with a rt2570 device.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CC [M] drivers/net/wireless/mwl8k.o
drivers/net/wireless/mwl8k.c: In function ‘mwl8k_bss_info_changed’:
drivers/net/wireless/mwl8k.c:3290:2: warning: ‘ap_mcs_rates’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(cmd->mcs_set, mcs_rates, 16);
^
drivers/net/wireless/mwl8k.c:4987:5: note: ‘ap_mcs_rates’ was declared here
u8 ap_mcs_rates[16];
^
The warning was bogus. But the conditionals were rather complicated,
with multiple redundant checks. This consolidates the checking and
makes it more readable IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I remove duplicated routines which related rtl92cu_set_hw_reg().
1. rtl92c_set_qos() and HW_VAR_AC_PARAM routine are similar code.
so i replace code with rtlpriv->cfg->ops->set_hw_reg().
2. rtl92c_set_mac_addr() and 'HW_VAR_ETHER_ADDR' case at
rtl92cu_set_hw_reg() routine are similar code.
so i removed rtl92c_set_mac_addr() function.
also it was not used anywhere.
3. remove HW_VAR_ACM_CTRL routine in rtl92cu_set_hw_reg().
if rtl_usb->acm_method is not EACMWAY2_SW, HW_VAR_ACM_CTRL is called
from HW_VAR_AC_PARAM. but it never called. because acm_method is always
EACMWAY2_SW. so i remove acm_method check routine
and HW_VAR_ACM_CTRL routine.
both usb and pci interface is not used HW_VAR_ACM_CTRL.
but i can't test pci interface module, so i didn't modify pci code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92c_set_xxx_filter is same routine with rtl92cu_set_hw_reg.
so i remove those functions that are rtl92c_set_xxx_filter.
(rtl92c_get_xxx_filter is also same reason.)
also i add code updating struct rtl_mac member variable in the
rtl92cu_set_hw_reg.
after that, no more _update_mac_setting is not useful. thus i remove that.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' mac80211-next.git
iwlwifi needs new mac80211 patches so merge mac80211-next.git to
wireless-drivers-next.git.
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WMI 10.4 uses the same command interface as QCA988X for addba/delba
debug wmi commands. Fill wmi_10_4_ops table with the functions used
for QCA988X for these commands.
With this change, the following debugfs entries can be used to
configure the aggregation mode and to send addba request,
addba response and delba respectively in manual aggregation mode
for QCA99X0 chip.
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/aggr_mode
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba_resp
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header format of 10.4 firmware phyerr event is not alligned
with pre 10.4 firmware. Introduce new wmi handlers to parse
10.4 firmware specific phyerror event header.
With changes covered in this patch, radar detection works on
qca9x0 hw 2.0 which uses 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
As remain is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/wil6210/wmi.c:827
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_WIL6210=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently it's not safe to install both pairwise
and groupwise keys on AP vdevs as it can cause
traffic to stop working in some multi-vif
(WPA+WEP) cases.
Fixes: ce90b27128 ("ath10k: fix multiple key static wep with ibss")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are three WMI_CHAN_INFO events reported per channel
in QCA99X0 firmware. First one is a notification at the begining
of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0),
second one is a notification at the end of the dwell time with cmd_flag
CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication
with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for
the channel. Since there is a new state before the completion, the handler
is to fixed so that the counts are deducted from the ones reported with
CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE.
Without this fix there will be lots of 0 msecs reported as active
and busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vif's vdev_id is used as queue number. However due
to the tx pausing design in ath10k it was possible
for a new interface to be created with its tx
queue stopped (via ieee80211_stop_queues). This
could in turn leave the interface inoperable until
ath10k_mac_tx_unlock() was called.
This problem only affected multi-vif scenarios when
new interfaces were created some time later after
other interfaces have been running for some time
and had Tx queue full at some point prior.
Possible manifestation of the bug was
authentication timeout for a client vif.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once HTT Tx queue got full offchannel queue was
stopped and never woken up again. This broke, e.g.
P2P. This could be reproduced after running a lot
of traffic enough to saturate 100% of the driver
Tx queue and then trying to send offchannel
traffic.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
wil6210:
* implement TSO support
* support bootloader v1 and onwards
Currently the driver disable power management on all low-latency
interfaces, while it should disable it on WiDi interfaces only.
Non-P2P interfaces that runs voice and video traffic should enable
power management.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS support is declared by the FW, set the bit indicating wider-BW
support as well.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The &mvm->tof_data.range_req.ap[] array has IWL_MVM_TOF_MAX_APS elements
so the check should be >= instead of >. Also the test can underflow so
I have changed "i" to unsigned.
Fixes: ce7929186a ('wlwifi: mvm: add basic Time of Flight (802.11mc FTM) support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in one case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.
When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' into next
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
Lmac sched scan supports partial scans, so we can set some channels to be
scanned on every scan iteration and others to be scanned only on some
iterations. Currently we set all channels to be scanned every iteration,
but still have some configuration of which iterations should be partial
and which should be full.
Remove all partial/full scan configuration to reduce confusions.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove timing values from iwl_mvm_scan_params and use defines and
arrays of values instead.
While at that fix few values and corner cases and align all OSs
to ChromeOS values.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We added calls to d3_suspend/resume trans ops during the
suspend/resume flow.
However, the wrapper code didn't verify the trans ops were
actually defined, resulting in panic when they were not
(such as in the case of sdio trans)
Fixes: 6dfb36c89d ("iwlwifi: call d3_suspend/resume in d0i3 case as well")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_orinocodev() would allocate the wiphy entry, but it would only get
registered much later in orinoco_init(). If something failed in the init
process inbetween the call to alloc_orinocodev() and the completion
of orinoco_init(), the drivers would end up calling wiphy_unregister()
with a NULL pointer causing beautiful OOPS fireworks.
Explicitly call wiphy_unregister() instead in the right places.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Our 8887 A2 chip can have separate firmware images for
bluetooth and WLAN. We observed an issue during parallel
downloading of these images by btmrvl and mwifiex drivers.
This patch claims sdio bus before starting of the firmware
download in mwifiex and releases it after completion to
fix the problem.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will check if any hidden SSID found in passive scan channels
and do specific SSID active scan for those channels.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware dump feature for SD8997 chipset.
The difference here is only one memory type is needed
to save all firmware information. Device dump information
will be uploaded to usersapace file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for 8997 chipset to mwifiex
with SDIO/PCIe/USB interface.
The corresponding firmware image files are located in:
"mrvl/sd8997_uapsta.bin"
"mrvl/pcie8997_uapsta.bin"
"mrvl/usb8997_uapsta.bin"
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code returns success if kmalloc fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this driver, two variables are masked by one quantity, and then tested
against a second number with more bits that the mask. Accordingly, the
test always fails. To minimize the possibility of such typos, a symbolic
definition of the mask is created and used.
The separate load and mask operations are also combined into a single
statement.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The drivers are converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e996db6983 (rtlwifi: rtl8192c: Add init codes for "fw_version"
and "fw_subversion") added initialization for fw_version, but failed to
note that the variable in the firmware header is little-endian. The
following Sparse warning results:
CHECK drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: expected unsigned short [unsigned] [usertype] fw_version
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: got restricted __le16 [usertype] version
When fixing this problem, I noticed that several of the drivers contain
nearly identical copies of the firmware header struct, and that only the one
used in rtl8192c{e,u} had correct endian notation. The struct has been
moved into a common header, and the other drivers will be fixed in
subsequant patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/link.c:197
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/wmi.c:331
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_hst.c:171
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:277
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:206
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec ("ath10k: allocate fw resources for iface combinations")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If peer creation failed during offchannel Tx the
driver attempted to delete the peer nonetheless.
This caused the ar->num_peers counter to be
incorrectly decremented. This subsequently could
cause the counter to drop below 0 and also
eventually lead to firmware crash because host
would think there are less peer entries created in
firmware then there really were.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WoWLAN resume fails with retval 1 mac80211
will attempt to reconfig the device in a similar
manner when hw restart is requested. This wasn't
handled properly and yielded call trace warnings
and the device ended up not working.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.
Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently
it will return "UNKNOWN".
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Add a spinlock which will ensure that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Since rx path is run in driver tasklet,
tx status cannot be reported directly from interrupt context
(there would be no way to lock it out).
Add tasklet for tx and move all possible code from irq handler
there.
Note: tx tasklet is needed because workqueue is queued very
rarely and that kills TCP performance.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx is run inside a tasklet so ieee80211_rx() should be used
instead of ieee80211_rx_ni().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
kbuild bot reported that commit 592fa228f2 ("ath9k: remove struct
ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 592fa228f2 ("ath9k: remove struct ath_atx_ac")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9MX3
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
For PCIe/USB chipsets, preallocated skb buffers are reused for
event handling. mwifiex_check_uap_capabilties() performs
skb_pull(). This patch adds missing skb_push() to restore skb's
data pointer/length.
This bug was introduced by commit debfc60081 ("mwifiex: update
AP WMM settings from BSS_START event")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preallocated event SKBs are getting reused for PCIe chipset.
Their physical addresses are shared with firmware so that
firmware can write data into them.
This patch makes sure that SKB is cleared and length is set to
default while submitting it to firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.
Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When WLAN interface is up and running, driver unload and
load was causing command timeout error.
We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup rxfiler correctly for offchannel ctx.
This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise p2p device support when ath9k loaded with
use_chanctx=1.
This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible
The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5e1 and shouldn't
have any consequence
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag
The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled
calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Boot loader versions as backward compatible,
starting from v1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader reports error starting from the struct v2.
Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.
For debug purposes, "PM" debug category introduced.
Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow network stack part of Rx processing to run on separate core,
relaxing CPU utilization on the core used for Rx NAPI.
If RXHASH feature is enabled, the driver sets rxhash of each skb to 1
to enable RPS. The core for processing the rx skb is determined by RPS
mechanism according to rx_cpus bit mask which is configured at user level.
For processing skbs on different core from the core which processes
the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".
Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the recent kernel versions, multiple MSI is not well supported.
In particular, it is not supported on x86 and ARM architectures.
Also, internal interrupt handling logic is simpler and
more effective when using single interrupt.
Remove support for 3 MSI, convert module parameter
"use_msi" from int with range [0,1,3] to boolean.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx drops may be for 2 reasons: frame is old,
or it is duplicate. On the debugfs "stations" entry,
provide counters per reorder buffer for total
frames processed, drops for these 2 reasons.
Also add debug print for dropped frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When printing error message, provide string describing IE kind.
Derive it from IE type
This allows removing of error messages printing
in callers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sort overall IE's handling
prepare code (disabled for now) to add IEs for the beacon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW is allowed to generate WMI events that are not handled by this driver.
Treat such case as warning instead of error.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check event length;
hex dump both Rx and Tx frames
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver report supported TSO (v4 & v6) and IP checksum offload
in addition to previously supported features. In data path
skbs are checked for non-zero gso_size, and when detected sent
to additional function for processing TSO SKBs. Since HW does not
fully support TSO, additional effort is required from the driver.
Driver partitions the data into mss sized descriptors which are
then DMAed to the HW.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading with debug_fw flag, do not bail out on
unknown chipId
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use function wil_fw_error_recovery() instead of inline equivalent code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Multiple del_station requests may be sent to the driver by the
supplicant when turning down AP. This may overflow mailbox
between the FW and ucode
Wait till disconnect of one STA completed before sending next command.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
linux/device.h should be included using <>, not ""
since it is not local include
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the debugfs, there is "ulong" attribute printing.
It is used for bitmap printing, and more appropriate format
would be hexadecimal, not decimal.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When performing Rx reordering, count skb's dropped
per reorder buffer; and print dropped packets count
on the "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are 2 versions of boot loader struct: v0 and v1.
In the v1, boot loader build version added; as well as
RF status.
Support both versions.
Boot loader structure v1 has RF status; ignore RF error if firmware
not going to be loaded; driver can still be used to interact with the HW
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When building a Tx Command for management frames, we are lacking
a check for action frames, for which we should set a different
pm_timeout. This cause the fw to stay awake for 100TU after each
such frame is transmitted, resulting an excessive power consumption.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.
In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.
When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt, and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.
The driver can support up to 1 MB of pages.
Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As a preperation for multiple RX queues change the RBD
allocation model.
The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.
The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.
Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.
New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow frag SKBs in PCIe and advertise the maximum number of frags
to the opmode. As a fallback. linearize the SKB if it exceeds the
maximum number of fragments. This allows using the hardware better
(filling more TBs) and should improve performance when used by the
opmode.
Also adjust tracing to be able to deal with this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan is a scan feature which is supported on certain devices only,
hence the need for a TLV flag for it. For devices that support gscan
store the gscan capabilities advertised by the FW so the driver can
report it to upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set max TX aggregation size for 8260 SDIO devices series to 40 frames.
Fine tune max RX aggregation size - change it to 21.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler used to suffer from false wake-up on 500 time units.
We had to came up with a formula to address this buggy behavior.
Now that our firmware is fixed, we can go back to our old policy.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for dumping all the RBs in the RX queue
when FW error occurs.
This will assist debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Print the CPU1 and CPU2 secured boot status registers from the NIC
to indicate a SYSASSERT during secured engine unlocking process
on init/protocol image.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.
In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.
When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.
The driver can support up to 1 MB of pages.
Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended command id in triggers handling.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended firmware event header that contains
a group id as well as the command id.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes various functions in the file rs.c void due to these
functions never returning a error code to signal to their callers
if and how they have failed to complete their intended work.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.
For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the CSR_DRAM_INIT_TBL_WRITE_POINTER bit wasn't set
on ict reset, in some flows (like disable ict followed by
immediate reset ict) the driver and hardware went out
of sync (the driver cleared the ict_index, while the hw
kept it intact).
Fix it by setting the flag when resetting ict.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).
Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.
After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CQM overwrites a few thresholds in the bf command. On the other hand,
when entering D0i3 the thresholds are set to higher values on purpose,
so ignore CQM in this case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Aniket Nagarnaik