This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During probe, the Baytrail audio driver reports errors such as:
[44.172040] baytrail-pcm-audio baytrail-pcm-audio: error: invalid DMA engine 0
[44.172137] baytrail-pcm-audio baytrail-pcm-audio: sst_dma_new failed
Those error messages are misleading, there is no error since the DMA
is explicitly not configured for Baytrail.
Add a test to remove DMA error checks when DMA is not configured
and return silently.
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If den=1 and pllin_rate>20MHz then den and num are adjusted to 0
causing a divide by zero error a few lines further on. Therefore
this patch correctly scales num and den such that
pllin_rate/den < 20MHz as required in the device data sheet.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: stable@vger.kernel.org
ppc has special instruction forms to efficiently load and store values
in non-native endianness. These can be accessed via the arch-specific
{ld,st}_le{16,32}() inlines in arch/powerpc/include/asm/swab.h.
However, gcc is perfectly capable of generating the byte-reversing
load/store instructions when using the normal, generic cpu_to_le*() and
le*_to_cpu() functions eaning the arch-specific functions don't have much
point.
Worse the "le" in the names of the arch specific functions is now
misleading, because they always generate byte-reversing forms, but some
ppc machines can now run a little-endian kernel.
To start getting rid of the arch-specific forms, this patch removes them
from all the old Power Macintosh drivers, replacing them with the
generic byteswappers.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds missing dai_link stream_name
which is used when DPCM
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver sometimes fixups debug/error message format
30cc4faf70
(ASoC: rsnd: tidyup debug message format and timing)
337b0b4c5f
(ASoC: rsnd: error meesage indicates its port)
But, it still exist un-fomated error message. This patch fixup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be SRC interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be SSI interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to ensure that 'alsactl restore' does not apply default
initialisation as the chip reset defaults are preferred.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
David suggested that the name "power_mgmt" is too ambiguous. Rename
the flag with a bit clearer one "power_save_node".
Also, add the corresponding description to HD-Audio.txt, too.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some pins are used for controlling the LED with the VREF value.
This patch changes the power behavior of such pins to be constantly
up. A new state, pin_fixed, is introduced to nid_path to indicate
that the path contains the fixed pin. This improves also the
readability a bit for other static routes, too.
Then a helper function snd_hda_gen_fix_pin_power() is called from the
codec driver for such fixed pins, and it will create fake paths
containing only these pins with pin_fixed=1 flag.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Constify local structures (snd_soc_dai_ops, snd_soc_codec_driver,
regmap_config) and array (reg_defaults) which are not modified by the
driver and passed to core as pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the sst_acpi_probe memory allocation error path by setting right error
code and initiating the cleanup insteadof just returning
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check waves state before set parameter through ipc to prevent unexpected
operation. Also remove redundant check.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel MID DMA driver is going to be removed, commit should be a few lines
down near to dmaengine_slave_config() call in order to not confuse and at
quick look Synopsys DesignWare does seem to use some of the slave config
structure fields (see drivers/dma/dw/core.c: dwc_config()).
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel MID DMA driver is going to be removed by the coming commit
36111da783 ("dmaengine: intel-mid-dma: remove the driver") in spi.git
tree. Since there are no users for SST_DMA_TYPE_MID type the support for it
can be removed from here in advance.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the widget PM may turn off the pins, this might lead to the silent
output for beep when no explicit paths are given. This patch adds
fake output paths for the beep widget so that the output pins are
dynamically powered upon beep on/off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs used to have the own power controls but they were disabled
at transition to the generic parser due to the coding assuming the
fixed routes. Now we get the proper support of equivalently fine
power management in the generic parser, and the old kludges can be
replaced with it. This results in the reduction of lots of dead
codes.
The advanced PM feature is disabled as default like before for keeping
the compatible behavior. It's enabled via "Dynamic Power-Control"
mixer element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the finer power state control of each widget
depending on the jack plug state and streaming state in addition to
the existing power_down_unused power optimization. The new feature is
enabled only when codec->power_mgmt flag is set.
Two new flags, pin_enabled and stream_enabled, are introduced in
nid_path struct for marking the two individual power states: the pin
plug/unplug and DAC/ADC stream, respectively. They can be set
statically in case they are static routes (e.g. some mixer paths),
too.
The power up and down events for each pin are triggered via the
standard hda_jack table. The call order is hard-coded, relying on the
current implementation of jack event chain (a la FILO/stack order).
One point to be dealt carefully is that DAC/ADC cannot be powered
on/off while streaming. They are pinned as long as the stream is
running. For controlling the power of DAC/ADC, a new patch_ops is
added. The generic parser provides the default callback for that.
As of this patch, only IDT/Sigmatel codec driver enables the flag.
The support on other codecs will follow.
An assumption we made in this code is that the widget state (e.g. amp,
pinctl, connections) remains after the widget power transition (not
about FG power transition). This is true for IDT codecs, at least.
But if the widget state is lost at widget power transition, we'd need
to implement additional code to sync the cached amp/verbs for the
specific NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add sampling rate control for ADC/DAC for ESI W192M.
Allow to switch between 48K/96K/192K sampling rate.
All DAC need to be mute when changing samplerate.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add text Line in/Mic for selecting input gain state in mixer for ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add TLV support to control volume using dB scale for input and ouput on ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable midi i/o port of envy24 chip as their are available on ESI W192M soundcard.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update eeprom structure to C99 standard to be compliant with change in alsa.
It's just a notation change, no configuration change.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct copy/paste name from prodigy driver, no behaviour change, only name.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dai-link params for codec-codec links were fixed. The fixed
link between codec and another chip which may be another codec,
baseband, bluetooth codec etc may require run time configuaration
changes. This change provides an optional alsa control to select
one of the params from a list of params.
Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does two things:
- code refactoring with a local helper function,
- allow codec drivers to provide the specific PCM stream info pointers
only for overriding the non-NULL entries, instead of copying the
whole.
This simplifies the codec driver side (currently the only user is
alc269's 44kHz fixed rate).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCA+HAAoJECTWi3JdVIfQ6oQIAIOFlrPzKpI3C7MqrK6F+ySC
g/JOf8XZKbStl+RdSu/RI6gL1Nc4VD7EHv5vEM2Br6KtUHQMoQYpsSiPvn1BFJBX
EkwY3eoDiIyPqQG7cGmdIF/8NXiZgJYh13coamrkdAhBFMXfmqlbrBHo71Z6o1ic
cg4rng3AmjyJ1NfUDsMW/KTX0F8AUTw7yYs+B4pyjfRBFVmhmzubXGXNjiW+/Tz4
zjk9c3Qm7ZxC66dbvg5lpIakwbRtX26p7Fn+pWOewL4y81y9qruSvV6IgDZ1RO95
DRtLsU7qyIK3G9zCw61xJNiL2QAfgOfYYgi7R6XrlS3nttIFT30oELw5ObwjSM0=
=iSeG
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
It needs DAC -> Playback route instead of direct settings via
SND_SOC_DAPM_DAC. otherwise, it can't find correct path if
sound card used prefix name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jack creation code was in rt5670 codec driver before due to the
jack resources (gpio/irq) were defined under the node of codec device
in ACPI on Braswell. We used the snd_soc_jack_new() to create a jack
instance.
But now snd_soc_jack_new() is removed from upstream and we can't
use snd_soc_card_jack_new() in codec driver, so we move the jack
creation code to machine driver and pass the jack instance to codec
driver for further processing.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Braswell, we need to add some machine specific setting before suspend
and after resume. For example, disable/enable jack detection in codec so
use snd_soc_card suspend_pre and resume_post ops for this purpose.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable WM8731 to support common clock framework.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit [ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch defines an API to select the clock source for specified filters.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA buffer and address can be accessed through the snd_pcm_runtime.
There is no need to manually track them in the driver's state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dapm_kcontrol_codec() is a extremely simple function and inlining it
typically results in less code than necessary for calling the non-inlined
version of the function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow for the Qualcomm Technologies ASoC drivers
to build.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the LPASS platform driver, the LPASS
CPU DAI driver and the Storm machine driver
configurations, and how to build them.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for the Storm board with the
IPQ806X SOC connected to the MAX98357A DAC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the representation of the DSP in the device
tree has changed from a required subnode to an
optional phandle, modify the test for DSP
existence in the LPASS CPU DAI driver,
accordingly.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
driver fixes for new regressions since v3.19. Second are fixes to the
common clock divider type caused by recent changes to how we round clock
rates. This affects many clock drivers that use this common code.
Finally there are fixes for drivers that improperly compared struct clk
pointers (drivers must not deref these pointers). While some of these
drivers have done this for a long time, this did not cause a problem
until we started generating unique struct clk pointers for every
consumer. A new function, clk_is_match was introduced to get these
drivers working again and they are fixed up to no longer deref the
pointers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nc5C
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove adc stereo2 filter since it is not in rt5645/rt5650 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit [2225e79b9b03: 'ALSA: core: reduce stack usage related
to snd_ctl_new()'], the id field of the newly added kctl is untouched,
thus all attribute like name string remain empty. The fix is just to
add the forgotten memcpy of the id field.
Fixes: 2225e79b9b ('ALSA: core: reduce stack usage related to snd_ctl_new()')
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
rt5650 and rt5645 use different register bits for TDM configuration.
This patch modifies rt5645_set_tdm_slot to support both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each kcontrol command includes a line of parameters up to 128 bytes.
kcontrol command to set param:
cset "name='Waves Set Param' <0x01,0xff,...>"
or
cset-bin-file "name='Waves Set Param' <path/to/binary/config/file>"
The parameter lines are stored in a buffer array, so can be read back from
buffer rather than from DSP, and be relaunched to DSP when resume from RTD3.
The buffer size is 160 parameter lines.
kcontrol command to reset the buffer:
cset "name='Waves Set Param' 0xff"
alsa-lib v1.0.29 or commit 6ea14c36 and f47480af are required to support the
kcontrol commands.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function to set parameters to module waves. The parameters can be set
only when module is enabled, and parameter size is limited to 500 Bytes.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add kcontrol to enable/disable module waves. IPC is valid only when module
is loaded. Also track module state over suspend so it's state can be restored
on resume.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device complies to the UAC1 standard but hides that fact with
proprietary descriptors. The autodetect quirk for Roland devices
catches the audio interface but misses the MIDI part, so a specific
quirk is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Rafa Lafuente <rafalafuente@gmail.com>
Tested-by: Raphaël Doursenaud <raphael@doursenaud.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was no check about the id string of user control elements, so we
accepted even a control element with an empty string, which is
obviously bogus. This patch adds more sanity checks of id strings.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try to load module waves and allocate runtime blocks for it if the firmware
image of module waves exists.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a general method to load firmware image, and apply to base firmware
image loading. With the method, the driver will support loading multiple
different modules in order to support different features.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We force enable "Mic Det Power" when a jack is inserted. Also, we
set codec idle_bias_off = true. As a result, codec driver will not
suspend as we expect.
On Braswell, we don't need the jack detection when suspend but need
it after resume, so export the jack suspend/resume APIs which are
provided for machine driver to control during suspend/resume.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the IRQ function support of rt5670. We use a flag
named dev_gpio in platform data to inform codec driver if the IRQ
function is used or not. Also, we export rt5670_set_jack_detect
for machine driver to pass the jack point.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver needs SSI/SRC/DVC regmaps, but it didn't have
regmap_config::name for devm_regmap_init_mmio().
Thus, debugfs initialization code tried to use same driver name
many times, and failed.
This patch adds eacy own name for regmap_config::name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver needs 1st/2nd DMA interface,
and 1st DMA is using DMAEngine, and 2nd is using local method now.
2nd DMA had been DMAEngine, but it was moved to local method by previous
patchset. But then, it lost PIO mode fallback when probe.
this patch recovers it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_init':
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(dev, "id/src/dst/chcr = %d/%x/%x/%08x\n",
^
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
Fixes: 288f392e72 ("ASoC: rsnd: add Audio DMAC peri peri support rework")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the sequencer driver is built in kernel, it may panic at boot
because of the uninitialized snd_seq_bus_type. Initialize it properly
via subsys_initcall() instead of module_init() to assure that the bus
is registered beforehand.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 7c37ae5c62 ('ALSA: seq: Rewrite sequencer device binding with standard bus')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A playback noise happens after suspend/resume on Braswell. The issue is due to
the codec PLL and codec ASRC are not enabled correctly due to the incorrect
sysclk setting after resume. This patch resets the sysclk source setting in
platform clock control widget handler.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The kernel memory allocators already report the errors when the
requested allocation fails, thus we don't need to warn it again in
each caller side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel memory allocators already report the errors when the
requested allocation fails, thus we don't need to warn it again in
each caller side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel memory allocators already report the errors when the
requested allocation fails, thus we don't need to warn it again in
each caller side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The callers of snd_ctl_new() need to have 'struct snd_kcontrol' data,
and pass the data as template. Then, the function allocates the structure
data again and copy from the template. This is a waste of resources.
Especially, the callers use large stack for the template.
This commit removes a need of template for the function, thus, changes
the prototype of snd_ctl_new(). Furthermore, this commit changes
the code of callers, snd_ctl_new1() and snd_ctl_elem_add() for better
shape.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The parameters can be decided in compile time.
This commit adds precomputed table to reduce calculating time.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With previous commit, this module managed to leave the counting to each
drivers, but the isochronous resources functionality still increment/decrement
the count.
This commit purge such codes to leave the responsibility to each drivers.
Fix: c6f224dc20 ('ALSA: firewire-lib: remove reference counting')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_timeout can be called with timeout == 0 due to
msecs_to_jiffies(2) == 1 for HZ < 1000 and usecs_to_jiffies(300) == 1
for all reasonable values of HZ, thus the following timeout /= 2; sets
timeout to 0. This patch simply adds a lower-bounds of 1.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up
in case of completion occurring the remaining time is >=1 so ret is set to
1 if no timeout occurred.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, is_sys_clk_from_pll check sysclk source by reading codec
register value. And it will be invoked before updating dapm widget
power. In some machine driver, snd_soc_dai_set_sysclk is called in
dapm event to switch codec sysclk to RC clock in idle mode. And in
some use cases (such as syspend/resume) hw_params will not be called
when the dapm widget is powered up. As a result, is_sys_clk_from_pll
will return 0 although it is supposed to be 1.
To solve this, we let is_sys_clk_from_pll check sysclk sysclk_src
which is stored in private data and don't change the value of sysclk_src
when codec sysclk is switched to internal clock. The internal clock
can only be used in idle mode, so it sould be fine if we don't set
sysclk_src to internal clock.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Keep sysclk on if JD func is used" patch force enable/disable
pin in rt5670_set_dai_sysclk. But some machine driver call it in
dapm widget event. It will cause kernel crash.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jz4780 and jz4740 have very similar i2s blocks.
The slight difference is in Rx/Tx fifos.
And the bitclocks for input/output are different.
This patch adds jz4780 support to the driver
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit [63e51fd708f5: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021
Fixes: 63e51fd708 ('ALSA: hda - Don't take unresponsive D3 transition too serious')
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit d29697dc3b ("ASoC: Add sysfs entries via static attribute
groups") the sysfs attributes of the rtd are manged by the device core and
there is no need to manually call device_remove_file() anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Any access to the component_list, codec_list and platform_list needs to be
properly locked by the client_mutex. Otherwise undefined behavior can occur
if the list is modified in one thread and concurrently accessed from another
thread.
This patch adds the missing locking to the debugfs file handlers that
display the registered components, as well as the various components
unregister functions.
Furthermore the client_lock is now held for the whole
snd_soc_instantiate_card() sequence to make sure that component removal does
not race against the card registration.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
dma-names on DT was implemented as no difference between 1st / 2nd
DMAC's, since rsnd had assumed that both DMACs are implemented as
DMAEngine. That style was "src_dst". But now, 2nd DMAC was implemented
as non DMAEngine, and it doesn't need dma-names anymore. So, this
dma-names rule is no longer needed.
And additionally, dma-names was assumed that it has all
(= SSI/SSIU/SRC/DVC) nodes under sound node.
In upstream code, no SoC/platform is supporting DMA for rsnd driver yet.
This means there is no compatible issue if this patch changes
dma-names's rule of DT.
This patch assumes dma-names for 1st DMAC are tx/rx base, and listed
in each SSI/SRC/DVC subnode
ex)
rcar_sound,dvc {
dvc0: dvc@0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
...
rcar_sound,src {
src0: src@0 {
...
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
...
rcar_sound,ssi {
ssi0: ssi@0 {
...
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_dvc_of_node() to get DVC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_src_of_node() to get SRC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_ssi_of_node() to get SSI subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound driver uses SSI, but the DMA interfaces are
SSI/SSIU. This interface is based on SSI/SRC/DVC connection.
And DMA function needs to know which interface is used somehow.
This patch enables rsnd_ssi_use_busif() for DMA.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car needs 2 DMACs.1st DMAC is DMAEngine, and 2nd DMAC is
implemented as local code. These 2 DMACs are never shared.
We can use union for these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine direction can be calculated from rsnd_dai_stream,
So, rsnd_dma::dir does not make sense now.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine for Renesas R-Car driver is used only for Audio DMAC now.
rsnd_dma::addr was added to support Audio DMAC peri peri,
but it is no longer needed. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri is controlled from sound driver without DMAEngine
by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver needs to care about Audio DAMC (via DMAEngine),
Audio DMAC peri peri (via local method) on rsnd driver.
This patch adds new rsnd_dma_ops and care it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have dma.c for Audio DMAC / Audio DMAC peri peri.
rsnd_gen_dma_addr() should go there.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver had been assumed that Audio DMAC /
Audio DMAC peri peri are implemented by DMAEngine. But, result of DMA
ML discussion, it was concluded that it is not a general purpose DMAC.
And it should be moved from current DMAEngine to rsnd driver.
So, Audio DMAC peri peri become non DMAEngine.
OTOH, ALSA SoC has soc-generic-dmaengine-pcm implementation. but it
seems difficult to use this generic implementation on rsnd driver at
this point, since it needs to fallback to PIO mode if DMA can't use.
and additionally it needs 2 DMAC (= Audio DMAC / Audio DMAC peri peri).
These are not "generic" feature.
Of course I will try to use this generic dmaengine in the future somehow,
but just use current style at this point until it can formally use 2 DMACs.
This patch adds new dma.c and moves current dma code to dma.c from core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
physical address is required from Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver needs to support Audio DMAC peri peri inside sound driver.
getting resource by name is useful for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_available() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can get DMA direction via rsnd_dai_stream.
Remove un-needed is_play from rsnd_dma_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound had SH-DMA-BASE specific implementation before,
but, now, it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Details:
1. Unload all modules on fw_list of dsp when suspend, and reload all
modules on fw_list when resume.
2. A DSP expects only one scratch, but hsw_parse_fw_image() allocates
scratch blocks for each firmware image it parses. Move the allocate function
sst_block_alloc_scratch() out of hsw_parse_fw_image() to make sure a scratch
be allocated only after all firmware images be parsed.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The board ID will be changed between revisions. So, it is better
to map it by project name.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached
value instead of writing it directly.
Patch inspired by Russell King's more colorful remarks in this
patch:
https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6a
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
For broadwell machine, we need do some machine related setting before
suspend and after resume, e.g. disable/enable jack detection, here
adding snd_soc_card suspend_pre and resume_post for this task.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change to enable OMAP5 support on this platform was a little too
eager in adding a 'select' for a particular clock driver that might
not be enabled in all configurations, which in turn leads to a build
error:
warning: (SND_OMAP_SOC_OMAP_ABE_TWL6040) selects COMMON_CLK_PALMAS which has unmet direct dependencies (COMMON_CLK && MFD_PALMAS)
drivers/built-in.o: In function `palmas_clks_probe':
drivers/clk/clk-palmas.c:228: undefined reference to `palmas_ext_control_req_config'
I do not see a strong dependency here, so it's probably better to
drop this select and to avoid adding more complexity here.
Fixes: 5163c1eede ("ASoC: omap: Kconfig: Support for omap5-uevm analog audio")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can simplify the code by returning patch_build_controls() directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch to add an VT1613 AC97 codec support.
This codec has additional DC offset removal control,
headphone output and no video input.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU96stAAoJECTWi3JdVIfQLfUH/jBYQqxrPp8qm7Lt9LOuwC4U
SOi0ERIVhLSKZMo7G4wHmbEapx2FBgH+wxqh9kNLaISvOIH4odFS4Fr1XYE70cY9
97M46uzLqdaKCDgvkXdx1NLA0zubEGWLOtdVYlrMAzin0FXNH+KYhxkRQbJ6f0LE
yKmNemnHHtJ4gDl/kMED7bc+mkYSOpwUE/8HLOEA8bcE3luDnj7rvQwOhPIYq0Tz
Ij4GM8HSfWPp/k3YmZVcF8GA6icN3LG5Jg7DOu6S19fMYimTDaHQDCw0AoLfiIOQ
DykyHg7ay/I3B6zUz4JikLIW5KjFxZfeQ818YE0GQ4PgePfb0GSIFt0LnNmq4Oo=
=GIb7
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
A few driver specific fixes here, none of them earth shattering in
themselves, that have accumliated since the opening of the merge window.
There is a missing lower bound check on "pitchbend" so it means we can
read up to 6 elements before the start of the opl3_note_table[] array.
Thanks to Clemens Ladisch for his help with this patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduced by commit:
6afda7f507 ASoC: davinci-mcasp: Allow complete shutdown of McASP when not in use
I'm really sorry for this...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the CPU DAI driver for the Qualcomm
Technologies low-power audio subsystem (LPASS).
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the LPASS header files for ipq806x SOC. This
includes the register definitions for the ipq806x
LPAIF, and the structure definition for the driver
data.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/tegra/tegra_rt5677.c:334:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes some small issues on the probe error paths. Firstly,
fail probe if we can't register the regulator notifiers as this
will cause the cache to never be synchronised which will result in odd
behaviour if the regulators are controllable. Secondly, we don't need to
call regulator_bulk_disable if the enable fails, because the regulator
core will handle this clean up for us. Finally, we need to disable the
regulators if snd_soc_register_codecs fails.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is more idiomatic and also fixes an issue where the notifiers were
being leaked if probe failed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rearrange the pm_runtime_get/put_sync calls so the IP will be turned off
when it is not in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to i.MX6 Series Reference Manual, the formula to calculate
the sys clock is
sysclk rate = bclk rate * (div2 + 1) * (7 * psr + 1) * (pm + 1) * 2
Commit aafa85e71a ("ASoC: fsl_ssi: Add DAI master mode support for
SSI on i.MX series") added the divisor calculation which relies on
the clk_round_rate(). However, at that time, clk_round_rate() didn't
provide closest clock rates for some cases because it might not use
a correct rounding policy. So using the original formula (pm + 1) for
PM divisor was not able to give us a desired clock rate. And then we
used (pm + 2) to do the trick.
However, the clk-divider driver has been refined a lot since commit
b11d282dbe ("clk: divider: fix rate calculation for fractional rates")
Now using (pm + 2) trick would result an incorrect clock rate.
So this patch fixes the problem by removing the useless trick.
Reported-by: Stephane Cerveau <scerveau@voxtok.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usages of clamp() macro in sound/usb/line6/playback.c are just
wrong, the low and high values are swapped.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All of the things in the CODEC probe, such as getting the regulators and
verifying the chip ID, are better done in bus probe. It is better to
fail during bus probe if this is the wrong chip and all resource
allocation should be done in the bus probe anyway. This patch merges
the CODEC probe into bus probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify dependencies by using new style split out bus interfaces.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_property_read_u32_array returns 0 on success,
so the return value shouldn't be inverted twice,
first on assignment then in condition expression.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Routes without a control must use NULL for the control name. The sn95031
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the sn95031 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Routes without a control must use NULL for the control name. The da732x
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the da732x driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Routes without a control must use NULL for the control name. The ak4671
driver uses "NULL" instead in a few places. Previous to commit 5fe5b767dc
("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
the DAPM core silently ignored non-NULL controls on non-mixer and non-mux
routes. But starting with that commit it will complain and not add the
route breaking the ak4671 driver in the process.
This patch replaces the incorrect "NULL" control name with NULL to fix the
issue.
Fixes: 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non mixer/mux widgets")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We need to set left/right control for the speaker amp to get stereo
output on speaker.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sDMA support only transfer elements with 1, 2, and 4 byte physical
size. Initialize the pcm driver accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAI drivers has been converted to use edma-pcm instead of davinci-pcm
and the driver can be removed from the tree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm performs as good as the old davinci-pcm and it's use does not
require the 'ping-pong' mode of davinci-pcm, which was introduced to
overcome under/over flow issues when using davinci-pcm.
Keep the SND_DAVINCI_SOC config option to select the SND_EDMA_SOC to avoid
regression in audio support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm can replace the old davinci-pcm as platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm can replace the old davinci-pcm as platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
edma-pcm going to replace davinci-pcm as platform driver for daVinci
platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should be
set to 32.
The 64 was introduced by commit (in 2009):
a152ff24b9 ASoC: OMAP: Make DMA 64 aligned
But the dma_mask and coherent_dma_mask can not be used to specify alignment.
Fixes: a152ff24b9 (ASoC: OMAP: Make DMA 64 aligned)
Reported-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jacks are typically card level elements, but are currently registered with a
CODEC. When it was originally introduced snd_soc_jack_new() took a
snd_soc_card as its parameter, but at that time DAPM was only implemented at
the CODEC level and there was only one CODEC per card. This made it clear
which CODEC to use for the jack DAPM operations. But the multi-component
patchset added support for having multiple CODECs per card and with it the
API was updated to register jacks with a specific CODEC instance instead.
Subsequently DAPM support at the card level has been introduced, but the
snd_soc_jack_new() API has so remained unchanged.
This leaves us with the issue that the DAPM pins that are managed by the
jack detection logic usually are part of the card DAPM context but are
accessed through a CODEC DAPM context. Currently this works fine, but might
break in the future if we take a more hierarchical approach to DAPM
contexts.
Furthermore with componentization progressing systems that do not register
a snd_soc_codec might appear, while these system may still want to able to
register a jack.
This patch addresses these issues by adding a new function called
snd_soc_card_jack_new() that can be used to register jacks with the card
rather than a CODEC.
This new function is mostly identical to snd_soc_jack_new() except that it
additionally allows to directly specify the DAPM pins associated with the
jack. This was done since most users of snd_soc_jack_new() typically call
snd_soc_jack_add_pins() right after it, which is not necessary with the new
API and allows to reduce the amount of boiler plate code.
The old snd_soc_jack_new() is re-implemented as a wrapper around
snd_soc_card_jack_new().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sn95031 driver currently gets the CODEC implicitly from the jack that is
passed to sn95031_jack_detection(). But the codec field is going to be
removed from the snd_soc_jack struct, so refactor things to pass the CODEC
explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix spelling typo found in alsa-driver-api.xml.
It is because this file is generated from comments in source files,
I have to fix source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
arizona_extcon_do_magic does not lend a lot of clarity to the purpose
of the function, and as all the registers used are described in the
datasheet there is no need to obfuscate the code. This patch renames the
function to arizona_extcon_hp_clamp, as it controls clamping on the
headphone output.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Move parts of linux/mfd/arizona/pdata.h and gpio.h into a new file in
the dt-binding directory for use by device tree bindings. This also
makes gpio.h redundant so remove it in the process.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the destructor code to device release callback for the codec
object instead. This is a safer place to release the resources than
dev_free callback in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The events that are handled by HD-audio drivers are no frequent and
urgent ones, so we can use the standard workqueue without any problem
nowadays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have all pieces ready, and put them into places:
- add the hda_pcm refcount to azx_pcm_open() and azx_pcm_close(),
- call the most of cleanup code in hda_codec_reset() from the codec
driver remove,
- call the same code also from the hda_codec object free.
Then the codec driver can be unbound more safely now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Revive snd_device_disconnect() again so that it can be called from the
individual driver. This time, HD-audio will need it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM ops might be set NULL, or cleared to NULL when the driver is
unbound. Give a proper NULL check at each place to be more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the hda_codec object kept the hda_pcm list in an array, and
the codec driver was expected to assign the array. However, this
makes the object life cycle management harder, because the assigned
array is freed at the codec driver detach while it might be still
accessed by the opened streams.
In this patch, we allocate each hda_pcm object dynamically and manage
it as a linked list. Each object has a kref refcount, and both the
codec driver binder and the PCM open/close touches it, so that the
object won't be freed while in use.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memory allocators should have already given the kernel warning
messages, thus we don't have to annoy again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the codec object to have an individual card pointer. Not only
this simplifies the redirections in many places, also this will allow
us to make each codec assigned to a different card object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_build_pcms() does actually three things: let the codec driver
build up hda_pcm list, set the PCM default values, and call the
attach_pcm bus ops for each hda_pcm instance. The former two are
basically independent from the bus implementation, so it'd make the
code a bit more readable.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So userspace can enable and disable the external microphone.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Also adds a control for the pin of the internal mic, so userspace can
apply policy when the state of the external mic jack changes.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
So userspace can enable or disable it based on the current policy.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch keeps the ldo2 power while the DSP function of "Voice Wake Up" used
in the suspend mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one clock source in the rt5676, so the chip type is added to
distinguish the setting of the clock source in the VAD function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec is in slave mode, ASRC can suppress noise for asynchronous
MCLK and LRCLK or special I2S format. This patch defines an API to select
the clock source for specified filters. And the codec driver will turn on ASRC
for these filters if ASRC is selected as their clock source.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous definition of registers 0x84 and 0x85 doesn't match the datasheet.
So this patch removes the wrong definition and writes a new one for the two
registers.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
System clock is necessary for rt5670 JD function. We assume system
clock source will be set in machine driver. So there are two things
left we should do in codec driver.
1. Set sysclk to codec internal clock in probe since machine driver
may not do that before JD function is registered.
2. Power up PLL once sysclk source is switched to PLL.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds runtime PM support on rt5670 codec.
Signed-off-by: Lin Mengdong <mengdong.lin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set specific data according to dmi data.
Signed-off-by: Jin, Yao <yao.jin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Atmel based boards can now only be used with device tree. Drop non DT
initialization.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For received packet stream, the offset of 'RX_SEQ_START' locates after
the offset of 'RX_NUMBER_MIDI', although current macro and proc output
includes wrong offsets.
Fortunately, this bug doesn't affect streaming functionality because
these macro is not used.
This commit fixes these wrong macro and outputs.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amdtp_stream_wait_callback() doesn't return minus value and
the return code is not for error code.
This commit fixes with a propper condition and an error code.
Fixes: f3699e2c77 ('ALSA: oxfw: Change the way to start stream')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We leave the pcm field of struct hda_pcm at removal of each device, so
far. This hasn't been a problem since unbinding the codec driver
isn't supposed to happen and another route via snd_hda_codec_reset()
clears all the once. However, for a proper unbind implementation, we
need to care about it.
This patch does the thing above properly:
- Include struct hda_pcm pointer instead of struct hda_pcm_stream
pointers in struct azx_dev. This allows us to point the hda_pcm
object at dev_free callback.
- Introduce to_hda_pcm_stream() macro for better readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we let the controller driver power down the all codecs at the
end of probe. But this can be done better in the codec's dev_register
callback. This results in the reduction of duplicated codes in each
control driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the final bit of runtime PM cleanup: instead of manual
notification of the power up/down of the codec via hda_bus pm_notify
ops, use the standard runtime PM feature.
The child codec device will kick off the runtime PM of the parent
(PCI) device upon suspend/resume automatically. For managing whether
the link can be really turned off, we use the bit flags
bus->codec_powered instead of the earlier bus->power_keep_link_on.
flag. Each codec driver is responsible to set/clear the bit flag, and
the controller device can be turned off only when all these bits are
cleared.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to pass the power_save option value to hda_bus via a given
pointer. This was needed to refer to the value from the HD-audio core
side. However, after the transition to the runtime PM, this is no
longer needed.
This patch drops the power_save value indirection in hda_bus above,
and let the controller driver reprograms the autosuspend value
explicitly by a new helper, snd_hda_set_power_save(). Without this
call, the HD-audio core doesn't set up the autosuspend and flip the
runtime PM. (User may still be able to set up via sysfs, though.)
Along with this change, the pointer argument of azx_bus_create() is
dropped as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes faulty behaviour in a setup where the input clock for the
SRG is fed through the CLKR/CLKX pin but the McBSP is configured to be
master (SND_SOC_DAIFMT_CBS_CFS). In that case of course CLKR/CLKX must
not be configured as output pin. Otherwise the input clock is messed up
horribly.
This patch makes it possible to use the CLKR/CLKX pin rather than CLKS to
inject a reference clock in setups where McBSP is master and not both
rx and tx are used. However for this to work it has to be ensured that
set_dai_sysclk() is called after set_dai_fmt().
This was tested on a beagleboard-xm using McBSP1 to drive a i2s DAC through
the tx lines (CLKX,FSX,DX). Using this patch the CLKR pin is used to inject
an external reference clock.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard naming convention for the codec DAI.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the routing paths of that after IF1/2 DACx Mux
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct dev_pm_ops defines usage_count only when CONFIG_PM is defined. So
we should use this variable only in cases where this falg is true.
So we define a local variable and read the value under this flag. In non PM
cases, we set this to 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A few minor tweaks to make things line up correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These weren't aligned on the same lines as the surrounding code and the
printk was quite messy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The indenting here was really whacky and not consistent from one line to
the next. I also reverse the "if (opened)" and "if (tmr_running)" tests
so that I could remove two indent levels.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is essentially a partial revert of the commit [b1920c21102a:
'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug
report showing the HD-audio bus hang during runtime PM on HP Spectre
XT.
Reported-by: Dang Sananikone <dang.sananikone@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some platforms, e.g. WSB, don't need jack detection when
system is in Suspend, for power save reason.
Here add headphone/mic jack detection disable feature with NULL
jack passed in, when disabled, it will disable interrupt, and
disable LDO1, which is used for jack detection when headphone
is plugged in.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds snd_soc_of_parse_audio_routing() to get dapm routes
configurations via Device Tree.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current helper functions, snd_soc_of_parse_audio_simple_widgets()
and snd_soc_of_parse_audio_routing(), set dapm_widgets and dapm_routes
without caring if they are already set by using build-in widgets and
routes in the card driver. So there could be one of them, build-in one
or Device Tree one, overrided by the other depending on which one was
assigned later.
This patch adds an extra pair of dapm_widgets and dapm_routes for DT
use only so as to prevent unexpected overriding.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using non-standard rates, a relatively small amount of overclocking
can make a big difference to a number of cases.
- Not all rates are possible to achieve with the PLL, due to divider
restrictions.
- The higher oversampling rates that can be used by the DAC, the
simpler the analog output filters get (mirror frequencies move up,
away from the desired spectrum).
- The more work the DSP can perform per sample, the better.
For standard rates, there is little to gain as everything is
designed just right, and the needed overclocking to make a
real difference would be significant.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is a bad idea to export static functions. GCC for some platforms
shows errors like:
error: __ksymtab_azx_get_response causes a section type conflict
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The STA32X_AUTO3 is a writable register that currently does not appear
in the regmap ranges(neither read nor write). By adding this register
to the register ranges there is no gap anymore and the existing
register ranges can be joined. This fixes a regression introduced in
commit a1be4cead9 where the driver was
moved to direct regmap usage and the STA32X_AUTO3 register was missed.
That made it impossible to choose the preset EQ mode set through the
STA32X_AUTO3 register.
Fixes: a1be4cead9 (ASoC: sta32x: Convert to direct regmap API usage)
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Also there is an *_optional variant that serves well here. The sematics
is slightly changed here by using it as error checking is more strict
now: If GPIOLIB is not enabled an error is returned instead of just
ignoring the gpio. On one hand this is bad for devices that don't "have"
the respective gpio as the driver is failing now. On the other hand
there is no means to assert that this gpio is really not needed or if
only the driver to control it is not available. The latter is a real
reason to fail and so it's defensive to fail here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5670_IRQ_CTRL1(0xbd) is a non volatile register. And we need to
restore its value after suspend/resume.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In our platform we want platform and codec driver routines to get invoked
and don't need the machine routines so remove here
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thus removing the runtime_resume handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for system pm support. We need to save the dsp memory
which gets lost on suspend and restore that on resume
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state. This patch covers that overlooked case.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai