Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming. However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.
Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3. These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Considering that generic.c is getting more and more bloated by device
information, moving that part out side will be much cleaner.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FFUART and friends are already defined as __REG(x) in pxa-regs.h.
Instead of redefining them here, we can just provide the __REG macro.
Including asm/arch/hardware.h is not an option because this physical
addresses are needed here.
This is a fix for the compiler warnings generated by 4663/1.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.
This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the SSP driver at arch_initcall() time, so it's available
for other drivers to use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. change SSP register definitions from absolute virtual addresses to
offsets
2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define "struct ssp_device" for SSP information, which is requested
and released by function ssp_request()/ssp_free()
2. modify the ssp_init() and ssp_exit() to use the interface
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Also, use existing register and bit definitions instead of numbers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace wakeup support using the alarm via the SA1100 RTC driver on
SA1100 and PXA platforms. This allows RTC alarm wakeup to be enabled
via sysfs using the conventional attributes.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OSCR is supposed to monotonically increment; however restoring it
to a time prior to OSMR0 may result in it being wound backwards.
Instead, if OSMR0 is within the minimum expiry time, wind OSMR0
forwards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux has framebuffer backlight support infrastructure which should
be used to expose backlight attributes. Mainstone should use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
If we know a buffer_head is non-null, then brelse() is unnecessary and
put_bh() can be used instead. Also, an explicit check for NULL is
unnecessary when using brelse(). This patch only covers buffer_head_io.c and
resize.c, which have recently added code which exhibits this problem.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
ocfs2_super->blocked_lock_list and ocfs2_super->blocked_lock_count have some
usage restrictions which aren't immediately obvious to anyone reading the
code. It's a good idea to document this so that we avoid making costly
mistakes in the future.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
configfs has been alive and kicking for a while now. It underpins some
non-EXPERIMENTAL subsystems, such as OCFS2's cluster stack.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Bump the printed version to 1.5.0. This helps us quickly identify which
version of Ocfs2 a bug filer is running.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Currently the process of dlm join contains 2 steps: query join and assert join.
After query join, the joined node will set its joining_node. So if the joining
node happens to panic before the 2nd step, the joined node will fail to clear
its joining_node flag because that node isn't in the domain map. It at least
cause 2 problems.
1. All the new join request will fail. So no new node can mount the volume.
2. The joined node can't umount the volume since during the umount process it
has to wait for the joining_node to be unknown. So the umount will be hanged.
The solution is to clear the joining_node before we check the domain map.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Convert byte order of constant instead of variable it will be done at
compile time vs run time. Remove unused le32_and_cpu.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Lots of people are having trouble with the default timeouts, which are too
low. These new values are derived from an informal survey taken on
ocfs2-users, as well as data from bug reports. This should reduce the amount
of cluster disconnects and subsequent fencing seen during normal workloads.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Russell King