Both damn things interpret userland pointers embedded into the payload;
worse, they are actually traversing those. Leaving aside the bad
API design, this is very much _not_ safe to call with KERNEL_DS.
Bail out early if that happens.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Partitions that are not aligned to the blocksize of a device may cause
invalid I/O requests because the blocklayer cares only about alignment
within the partition when building requests on partitions.
device
|--------4096--------|--------4096--------|--------4096--------|
partition offset 512byte
|-512-|--------4096--------|--------4096--------|--------4096--------|
When reading/writing one 4k block of the partition this maps to
reading/writing with an offset of 512 byte of the device leading to
unaligned requests for the device which in turn may cause unexpected
behavior of the device driver.
For DASD devices we have to translate the block number into a cylinder,
head, record format. The unaligned requests lead to wrong calculation
and therefore to misdirected I/O. In a "good" case this leads to I/O
errors because the underlying hardware detects the wrong addressing.
In a worst case scenario this might destroy data on the device.
To prevent partitions that are not aligned to the physical blocksize
of a device check for the alignment in the blkpg_ioctl.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The WRITE_SAME commands are not present in the blk_default_cmd_filter
write_ok list, and thus are failed with -EPERM when the SG_IO ioctl()
is executed without CAP_SYS_RAWIO capability (e.g., unprivileged users).
[ sg_io() -> blk_fill_sghdr_rq() > blk_verify_command() -> -EPERM ]
The problem can be reproduced with the sg_write_same command
# sg_write_same --num 1 --xferlen 512 /dev/sda
#
# capsh --drop=cap_sys_rawio -- -c \
'sg_write_same --num 1 --xferlen 512 /dev/sda'
Write same: pass through os error: Operation not permitted
#
For comparison, the WRITE_VERIFY command does not observe this problem,
since it is in that list:
# capsh --drop=cap_sys_rawio -- -c \
'sg_write_verify --num 1 --ilen 512 --lba 0 /dev/sda'
#
So, this patch adds the WRITE_SAME commands to the list, in order
for the SG_IO ioctl to finish successfully:
# capsh --drop=cap_sys_rawio -- -c \
'sg_write_same --num 1 --xferlen 512 /dev/sda'
#
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2]),
which employs the SG_IO ioctl() and runs as an unprivileged user (libvirt-qemu).
In that scenario, when a filesystem (e.g., ext4) performs its zero-out calls,
which are translated to write-same calls in the guest kernel, and then into
SG_IO ioctls to the host kernel, SCSI I/O errors may be observed in the guest:
[...] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[...] sd 0:0:0:0: [sda] tag#0 Sense Key : Aborted Command [current]
[...] sd 0:0:0:0: [sda] tag#0 Add. Sense: I/O process terminated
[...] sd 0:0:0:0: [sda] tag#0 CDB: Write Same(10) 41 00 01 04 e0 78 00 00 08 00
[...] blk_update_request: I/O error, dev sda, sector 17096824
Links:
[1] http://git.qemu.org/?p=qemu.git;a=commit;h=336a6915bc7089fb20fea4ba99972ad9a97c5f52
[2] https://libvirt.org/formatdomain.html#elementsDisks (see 'disk' -> 'device')
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Brahadambal Srinivasan <latha@linux.vnet.ibm.com>
Reported-by: Manjunatha H R <manjuhr1@in.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block IO fixes from Jens Axboe:
"A few fixes that I collected as post-merge.
I was going to wait a bit with sending this out, but the O_DIRECT fix
should really go in sooner rather than later"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Fix failed allocation path when mapping queues
blk-mq: Avoid memory reclaim when remapping queues
block_dev: don't update file access position for sync direct IO
nvme/pci: Log PCI_STATUS when the controller dies
block_dev: don't test bdev->bd_contains when it is not stable
In blk_mq_map_swqueue, there is a memory optimization that frees the
tags of a queue that has gone unmapped. Later, if that hctx is remapped
after another topology change, the tags need to be reallocated.
If this allocation fails, a simple WARN_ON triggers, but the block layer
ends up with an active hctx without any corresponding set of tags.
Then, any income IO to that hctx can trigger an Oops.
I can reproduce it consistently by running IO, flipping CPUs on and off
and eventually injecting a memory allocation failure in that path.
In the fix below, if the system experiences a failed allocation of any
hctx's tags, we remap all the ctxs of that queue to the hctx_0, which
should always keep it's tags. There is a minor performance hit, since
our mapping just got worse after the error path, but this is
the simplest solution to handle this error path. The performance hit
will disappear after another successful remap.
I considered dropping the memory optimization all together, but it
seemed a bad trade-off to handle this very specific error case.
This should apply cleanly on top of Jens' for-next branch.
The Oops is the one below:
SP (3fff935ce4d0) is in userspace
1:mon> e
cpu 0x1: Vector: 300 (Data Access) at [c000000fe99eb110]
pc: c0000000005e868c: __sbitmap_queue_get+0x2c/0x180
lr: c000000000575328: __bt_get+0x48/0xd0
sp: c000000fe99eb390
msr: 900000010280b033
dar: 28
dsisr: 40000000
current = 0xc000000fe9966800
paca = 0xc000000007e80300 softe: 0 irq_happened: 0x01
pid = 11035, comm = aio-stress
Linux version 4.8.0-rc6+ (root@bean) (gcc version 5.4.0 20160609
(Ubuntu/IBM 5.4.0-6ubuntu1~16.04.2) ) #3 SMP Mon Oct 10 20:16:53 CDT 2016
1:mon> s
[c000000fe99eb3d0] c000000000575328 __bt_get+0x48/0xd0
[c000000fe99eb400] c000000000575838 bt_get.isra.1+0x78/0x2d0
[c000000fe99eb480] c000000000575cb4 blk_mq_get_tag+0x44/0x100
[c000000fe99eb4b0] c00000000056f6f4 __blk_mq_alloc_request+0x44/0x220
[c000000fe99eb500] c000000000570050 blk_mq_map_request+0x100/0x1f0
[c000000fe99eb580] c000000000574650 blk_mq_make_request+0xf0/0x540
[c000000fe99eb640] c000000000561c44 generic_make_request+0x144/0x230
[c000000fe99eb690] c000000000561e00 submit_bio+0xd0/0x200
[c000000fe99eb740] c0000000003ef740 ext4_io_submit+0x90/0xb0
[c000000fe99eb770] c0000000003e95d8 ext4_writepages+0x588/0xdd0
[c000000fe99eb910] c00000000025a9f0 do_writepages+0x60/0xc0
[c000000fe99eb940] c000000000246c88 __filemap_fdatawrite_range+0xf8/0x180
[c000000fe99eb9e0] c000000000246f90 filemap_write_and_wait_range+0x70/0xf0
[c000000fe99eba20] c0000000003dd844 ext4_sync_file+0x214/0x540
[c000000fe99eba80] c000000000364718 vfs_fsync_range+0x78/0x130
[c000000fe99ebad0] c0000000003dd46c ext4_file_write_iter+0x35c/0x430
[c000000fe99ebb90] c00000000038c280 aio_run_iocb+0x3b0/0x450
[c000000fe99ebce0] c00000000038dc28 do_io_submit+0x368/0x730
[c000000fe99ebe30] c000000000009404 system_call+0x38/0xec
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Douglas Miller <dougmill@linux.vnet.ibm.com>
Cc: linux-block@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Reviewed-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
While stressing memory and IO at the same time we changed SMT settings,
we were able to consistently trigger deadlocks in the mm system, which
froze the entire machine.
I think that under memory stress conditions, the large allocations
performed by blk_mq_init_rq_map may trigger a reclaim, which stalls
waiting on the block layer remmaping completion, thus deadlocking the
system. The trace below was collected after the machine stalled,
waiting for the hotplug event completion.
The simplest fix for this is to make allocations in this path
non-reclaimable, with GFP_NOIO. With this patch, We couldn't hit the
issue anymore.
This should apply on top of Jens's for-next branch cleanly.
Changes since v1:
- Use GFP_NOIO instead of GFP_NOWAIT.
Call Trace:
[c000000f0160aaf0] [c000000f0160ab50] 0xc000000f0160ab50 (unreliable)
[c000000f0160acc0] [c000000000016624] __switch_to+0x2e4/0x430
[c000000f0160ad20] [c000000000b1a880] __schedule+0x310/0x9b0
[c000000f0160ae00] [c000000000b1af68] schedule+0x48/0xc0
[c000000f0160ae30] [c000000000b1b4b0] schedule_preempt_disabled+0x20/0x30
[c000000f0160ae50] [c000000000b1d4fc] __mutex_lock_slowpath+0xec/0x1f0
[c000000f0160aed0] [c000000000b1d678] mutex_lock+0x78/0xa0
[c000000f0160af00] [d000000019413cac] xfs_reclaim_inodes_ag+0x33c/0x380 [xfs]
[c000000f0160b0b0] [d000000019415164] xfs_reclaim_inodes_nr+0x54/0x70 [xfs]
[c000000f0160b0f0] [d0000000194297f8] xfs_fs_free_cached_objects+0x38/0x60 [xfs]
[c000000f0160b120] [c0000000003172c8] super_cache_scan+0x1f8/0x210
[c000000f0160b190] [c00000000026301c] shrink_slab.part.13+0x21c/0x4c0
[c000000f0160b2d0] [c000000000268088] shrink_zone+0x2d8/0x3c0
[c000000f0160b380] [c00000000026834c] do_try_to_free_pages+0x1dc/0x520
[c000000f0160b450] [c00000000026876c] try_to_free_pages+0xdc/0x250
[c000000f0160b4e0] [c000000000251978] __alloc_pages_nodemask+0x868/0x10d0
[c000000f0160b6f0] [c000000000567030] blk_mq_init_rq_map+0x160/0x380
[c000000f0160b7a0] [c00000000056758c] blk_mq_map_swqueue+0x33c/0x360
[c000000f0160b820] [c000000000567904] blk_mq_queue_reinit+0x64/0xb0
[c000000f0160b850] [c00000000056a16c] blk_mq_queue_reinit_notify+0x19c/0x250
[c000000f0160b8a0] [c0000000000f5d38] notifier_call_chain+0x98/0x100
[c000000f0160b8f0] [c0000000000c5fb0] __cpu_notify+0x70/0xe0
[c000000f0160b930] [c0000000000c63c4] notify_prepare+0x44/0xb0
[c000000f0160b9b0] [c0000000000c52f4] cpuhp_invoke_callback+0x84/0x250
[c000000f0160ba10] [c0000000000c570c] cpuhp_up_callbacks+0x5c/0x120
[c000000f0160ba60] [c0000000000c7cb8] _cpu_up+0xf8/0x1d0
[c000000f0160bac0] [c0000000000c7eb0] do_cpu_up+0x120/0x150
[c000000f0160bb40] [c0000000006fe024] cpu_subsys_online+0x64/0xe0
[c000000f0160bb90] [c0000000006f5124] device_online+0xb4/0x120
[c000000f0160bbd0] [c0000000006f5244] online_store+0xb4/0xc0
[c000000f0160bc20] [c0000000006f0a68] dev_attr_store+0x68/0xa0
[c000000f0160bc60] [c0000000003ccc30] sysfs_kf_write+0x80/0xb0
[c000000f0160bca0] [c0000000003cbabc] kernfs_fop_write+0x17c/0x250
[c000000f0160bcf0] [c00000000030fe6c] __vfs_write+0x6c/0x1e0
[c000000f0160bd90] [c000000000311490] vfs_write+0xd0/0x270
[c000000f0160bde0] [c0000000003131fc] SyS_write+0x6c/0x110
[c000000f0160be30] [c000000000009204] system_call+0x38/0xec
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Douglas Miller <dougmill@linux.vnet.ibm.com>
Cc: linux-block@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
We ran into a funky issue, where someone doing 256K buffered reads saw
128K requests at the device level. Turns out it is read-ahead capping
the request size, since we use 128K as the default setting. This
doesn't make a lot of sense - if someone is issuing 256K reads, they
should see 256K reads, regardless of the read-ahead setting, if the
underlying device can support a 256K read in a single command.
This patch introduces a bdi hint, io_pages. This is the soft max IO
size for the lower level, I've hooked it up to the bdev settings here.
Read-ahead is modified to issue the maximum of the user request size,
and the read-ahead max size, but capped to the max request size on the
device side. The latter is done to avoid reading ahead too much, if the
application asks for a huge read. With this patch, the kernel behaves
like the application expects.
Link: http://lkml.kernel.org/r/1479498073-8657-1-git-send-email-axboe@fb.com
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Everytime we need to read ->nr_samples, we should have flushed
the batch first. The non-mq read path also needs to flush the
batch.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we pass in to run the queue async, but don't flag the
queue to be run. We don't need to run it async here, but we should
run it. So fixup the parameters.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Takes a list of requests, and dispatches it. Moves any residual
requests to the dispatch list.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
We have a variant for all hardware queues, but not one for a single
hardware queue.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Instead of allocating a single unused biovec for discard requests, send
them down without any payload. Instead we allow the driver to add a
"special" payload using a biovec embedded into struct request (unioned
over other fields never used while in the driver), and overloading
the number of segments for this case.
This has a couple of advantages:
- we don't have to allocate the bio_vec
- the amount of special casing for discard requests in the block
layer is significantly reduced
- using this same scheme for other request types is trivial,
which will be important for implementing the new WRITE_ZEROES
op on devices where it actually requires a payload (e.g. SCSI)
- we can get rid of playing games with the request length, as
we'll never touch it and completions will work just fine
- it will allow us to support ranged discard operations in the
future by merging non-contiguous discard bios into a single
request
- last but not least it removes a lot of code
This patch is the common base for my WIP series for ranges discards and to
remove discard_zeroes_data in favor of always using REQ_OP_WRITE_ZEROES,
so it would be good to get it in quickly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both of these are metadata only commands that are not issued by the
writeback code and not directly relevant to the writeback bandwith.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In theory we could map other things, but there's a reason that function
is called "user_iov". Using anything else (like splice can do) just
confuses it.
Reported-and-tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit e73c23ff73 ("block: add async variant of
blkdev_issue_zeroout") messages like the following show up:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2368848 at
logical offset 0 with max blocks 1 with error 95
EXT4-fs (dm-1): This should not happen!! Data will be lost
Due to the following fallthrough introduced with
commit 2d253440b5 ("block: Define zoned block device operations"),
generic_make_request_checks() would accept a REQ_OP_WRITE_SAME bio only
if the block device supports "write same" *and* is a zoned one:
switch (bio_op(bio)) {
[...]
case REQ_OP_WRITE_SAME:
if (!bdev_write_same(bio->bi_bdev))
goto not_supported;
case REQ_OP_ZONE_REPORT:
case REQ_OP_ZONE_RESET:
if (!bdev_is_zoned(bio->bi_bdev))
goto not_supported;
break;
[...]
}
Thus, although the bio setup as done by __blkdev_issue_write_same() from
commit e73c23ff73 ("block: add async variant of blkdev_issue_zeroout")
would succeed, its actual submission would not, resulting in the
EOPNOTSUPP == 95.
Fix this by removing the fallthrough which, due to the lack of an explicit
comment, seems to be unintended anyway.
Fixes: e73c23ff73 ("block: add async variant of blkdev_issue_zeroout")
Fixes: 2d253440b5 ("block: Define zoned block device operations")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Factor out common code for setting REQ_NOMERGE flag which is being used
out at certain places and make it a helper instead, req_set_nomerge().
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Get rid of the inline.
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a new block layer operation to zero out a range of
LBAs. This allows to implement zeroing for devices that don't use
either discard with a predictable zero pattern or WRITE SAME of zeroes.
The prominent example of that is NVMe with the Write Zeroes command,
but in the future, this should also help with improving the way
zeroing discards work. For this operation, suitable entry is exported in
sysfs which indicate the number of maximum bytes allowed in one
write zeroes operation by the device.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Similar to __blkdev_issue_discard this variant allows submitting
the final bio asynchronously and chaining multiple ranges
into a single completion.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both blkdev_report_zones and blkdev_reset_zones can operate on a partition of
a zoned block device. However, the first and last zones reported for a
partition make sense only if the partition start sector and size are aligned
on the device zone size. The same applies for zone reset. Resetting the first
or the last zone of a partition straddling zones may impact neighboring
partitions. Finally, if a partition start sector is not at the beginning of a
sequential zone, it will be impossible to write to the first sectors of the
partition on a host-managed device.
Avoid all these problems and incoherencies by ignoring partitions that are not
zone aligned.
Note: Even with CONFIG_BLK_DEV_ZONED disabled, bdev_is_zoned() will report the
correct disk zoning type (host-aware, host-managed or none) but
bdev_zone_size() will always return 0 for zoned block devices (i.e. the zone
size is unknown). So test this as a way to ensure that a zoned block device is
being handled as such. As a result, for a host-aware devices, unaligned zone
partitions will be accepted with CONFIG_BLK_DEV_ZONED disabled. That is, the
disk will be treated as a regular block device (as it should). If zoned block
device support is enabled, only aligned partitions will be accepted.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After commit 287922eb0b ("block: defer timeouts to a workqueue"),
deleting the timeout work after freezing the queue shouldn't be
necessary, since the synchronization is already enforced by the
acquisition of a q_usage_counter reference in blk_mq_timeout_work.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently there's no way to enable wbt if it's not enabled in the
kernel config by default for a device. Allow a write to the
'wbt_lat_usec' queue sysfs file to enable wbt.
This is useful for both the kernel config case, but also if the
device is CFQ managed and it was turned off by default.
Signed-off-by: Jens Axboe <axboe@fb.com>
Make it clear that we are disabling wbt for the specified queued,
if it was enabled by default. This is in preparation for allowing
users to re-enable wbt, and not have it disabled automatically
again.
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow a write of '-1' to reset the default latency target for
a given device. This removes knowledge of the different default
settings for rotational vs non-rotational from user space.
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg allocates some per-cgroup data structures with GFP_NOWAIT and
when that fails falls back to operations which aren't specific to the
cgroup. Occassional failures are expected under pressure and falling
back to non-cgroup operation is the right thing to do.
Unfortunately, I forgot to add __GFP_NOWARN to these allocations and
these expected failures end up creating a lot of noise. Add
__GFP_NOWARN.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc MERLIN <marc@merlins.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some drivers often use external bvec table, so introduce
this helper for this case. It is always safe to access the
bio->bi_io_vec in this way for this case.
After converting to this usage, it will becomes a bit easier
to evaluate the remaining direct access to bio->bi_io_vec,
so it can help to prepare for the following multipage bvec
support.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixed up the new O_DIRECT cases.
Signed-off-by: Jens Axboe <axboe@fb.com>
If a ZBC device is partitioned and operations are performed on the partition
the zone information is rebased to the partition, however the zone reset
is not mapped from the partition to device as are other operations.
This causes the API (report zones / reset zone) to be unbalanced in this
regard. Checking for the zone reset op code explicitly will balance the
API.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that all conversions are done, move the FibreChannel bsg code over
to the bsg library.
This patch is derived from work done by Mike Christie in 2011 [1] but
only the iscsi parts got merged back then.
[1] http://marc.info/?l=linux-scsi&m=131149780921009&w=2
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add bsg_job_put() and bsg_job_get() so don't need to export
bsg_destroy_job() any more.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
bsg_softirq_done() and fc_bsg_softirq_done() are copies of each other, so
ditch the fc specific one.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fc_destroy_bsgjob() and bsg_destroy_job() are now 1:1 copies, so use the
latter. As bsg_destroy_job() comes from bsg-lib we need to select it in
Kconfig once CONFOG_SCSI_FC_ATTRS is active.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add reference counting to 'struct bsg_job' so we can implement a reuqest
timeout handler for bsg_jobs, which is needed for Fibre Channel.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The previous commit introduced the hybrid sleep/poll mode. Take
that one step further, and use the completion latencies to
automatically sleep for half the mean completion time. This is
a good approximation.
This changes the 'io_poll_delay' sysfs file a bit to expose the
various options. Depending on the value, the polling code will
behave differently:
-1 Never enter hybrid sleep mode
0 Use half of the completion mean for the sleep delay
>0 Use this specific value as the sleep delay
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
This patch enables a hybrid polling mode. Instead of polling after IO
submission, we can induce an artificial delay, and then poll after that.
For example, if the IO is presumed to complete in 8 usecs from now, we
can sleep for 4 usecs, wake up, and then do our polling. This still puts
a sleep/wakeup cycle in the IO path, but instead of the wakeup happening
after the IO has completed, it'll happen before. With this hybrid
scheme, we can achieve big latency reductions while still using the same
(or less) amount of CPU.
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
The newly added driver causes a harmless warning in some configurations:
block/blk-wbt.c:250:1: error: ‘inline’ is not at beginning of declaration [-Werror=old-style-declaration]
static bool inline stat_sample_valid(struct blk_rq_stat *stat)
This makes it use the expected format for the declaration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In both legacy and mq path, req count of plug list is computed
before allocating request, so the number can be stale when falling
back to slept allocation, also the new introduced wbt can sleep
too.
This patch deals with the case by checking if plug list becomes
empty, and fixes the KASAN report of 'BUG: KASAN: stack-out-of-bounds'
which is introduced by Shaohua's patches of dispatching big request.
Fixes: 600271d900002(blk-mq: immediately dispatch big size request)
Fixes: 50d24c34403c6(block: immediately dispatch big size request)
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Again a leftover from when the throttling code was generic. Now that we
just have the block user, get rid of the stat ops and indirections.
Signed-off-by: Jens Axboe <axboe@fb.com>
The bdi was a leftover from when the code was block layer agnostic.
Now that we just support a block layer user, store the queue directly.
Signed-off-by: Jens Axboe <axboe@fb.com>
The poll code is blk-mq specific, let's move it to blk-mq.c. This
is a prep patch for improving the polling code.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
A previous commit changed this to pass in the hardware queue, but
it was using the wrong hardware queue. Hence a request that was
allocated on one hardware queue ended up being issued on another
one, and that caused IO timeouts and oopses on some drivers. Since
the request holds hardware queue private resources, like a tag,
we can't just issue it on a different hardware queue.
Fixes: 2253efc850 ("blk-mq: Move more code into blk_mq_direct_issue_request()")
Signed-off-by: Jens Axboe <axboe@fb.com>
Enable throttling of buffered writeback to make it a lot
more smooth, and has way less impact on other system activity.
Background writeback should be, by definition, background
activity. The fact that we flush huge bundles of it at the time
means that it potentially has heavy impacts on foreground workloads,
which isn't ideal. We can't easily limit the sizes of writes that
we do, since that would impact file system layout in the presence
of delayed allocation. So just throttle back buffered writeback,
unless someone is waiting for it.
The algorithm for when to throttle takes its inspiration in the
CoDel networking scheduling algorithm. Like CoDel, blk-wb monitors
the minimum latencies of requests over a window of time. In that
window of time, if the minimum latency of any request exceeds a
given target, then a scale count is incremented and the queue depth
is shrunk. The next monitoring window is shrunk accordingly. Unlike
CoDel, if we hit a window that exhibits good behavior, then we
simply increment the scale count and re-calculate the limits for that
scale value. This prevents us from oscillating between a
close-to-ideal value and max all the time, instead remaining in the
windows where we get good behavior.
Unlike CoDel, blk-wb allows the scale count to to negative. This
happens if we primarily have writes going on. Unlike positive
scale counts, this doesn't change the size of the monitoring window.
When the heavy writers finish, blk-bw quickly snaps back to it's
stable state of a zero scale count.
The patch registers a sysfs entry, 'wb_lat_usec'. This sets the latency
target to me met. It defaults to 2 msec for non-rotational storage, and
75 msec for rotational storage. Setting this value to '0' disables
blk-wb. Generally, a user would not have to touch this setting.
We don't enable WBT on devices that are managed with CFQ, and have
a non-root block cgroup attached. If we have a proportional share setup
on this particular disk, then the wbt throttling will interfere with
that. We don't have a strong need for wbt for that case, since we will
rely on CFQ doing that for us.
Signed-off-by: Jens Axboe <axboe@fb.com>
We can hook this up to the block layer, to help throttle buffered
writes.
wbt registers a few trace points that can be used to track what is
happening in the system:
wbt_lat: 259:0: latency 2446318
wbt_stat: 259:0: rmean=2446318, rmin=2446318, rmax=2446318, rsamples=1,
wmean=518866, wmin=15522, wmax=5330353, wsamples=57
wbt_step: 259:0: step down: step=1, window=72727272, background=8, normal=16, max=32
This shows a sync issue event (wbt_lat) that exceeded it's time. wbt_stat
dumps the current read/write stats for that window, and wbt_step shows a
step down event where we now scale back writes. Each trace includes the
device, 259:0 in this case.
Signed-off-by: Jens Axboe <axboe@fb.com>
For legacy block, we simply track them in the request queue. For
blk-mq, we track them on a per-sw queue basis, which we can then
sum up through the hardware queues and finally to a per device
state.
The stats are tracked in, roughly, 0.1s interval windows.
Add sysfs files to display the stats.
The feature is off by default, to avoid any extra overhead. In-kernel
users of it can turn it on by setting QUEUE_FLAG_STATS in the queue
flags. We currently don't turn it on if someone just reads any of
the stats files, that is something we could add as well.
Signed-off-by: Jens Axboe <axboe@fb.com>
cfq_cpd_alloc() which is the cpd_alloc_fn implementation for cfq was
incorrectly hard coding GFP_KERNEL instead of using the mask specified
through the @gfp parameter. This currently doesn't cause any actual
issues because all current callers specify GFP_KERNEL. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e4a9bde958 ("blkcg: replace blkcg_policy->cpd_size with ->cpd_alloc/free_fn() methods")
Signed-off-by: Jens Axboe <axboe@fb.com>
If we insert a flush request, we clear REQ_PREFLUSH and/or REQ_FUA,
depending on flush settings. Since op_is_sync() factors those flags
in for deciding whether this request is sync or not, we should
set REQ_SYNC to avoid screwing up this accounting.
This should be less fragile.
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: b685d3d65a ("block: treat REQ_FUA and REQ_PREFLUSH as synchronous")
Signed-off-by: Jens Axboe <axboe@fb.com>
This will allow SCSI to have a single blk_mq_ops structure that either
lets the LLDD map the queues to PCIe MSIx vectors or use the default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 0e87e58bf6 ("blk-mq: improve warning for running a queue on the
wrong CPU") attempts to avoid triggering the WARN_ON in
__blk_mq_run_hw_queue when the expected CPU is dead. Problem is, in the
last batch execution before round robin, blk_mq_hctx_next_cpu can
schedule a dead CPU and also update next_cpu to the next alive CPU in
the mask, which will trigger the WARN_ON despite the previous
workaround.
The following patch fixes this scenario by always scheduling the value
in hctx->next_cpu. This changes the moment when we round-robin the CPU
running the hctx, but it really doesn't matter, since it still executes
BLK_MQ_CPU_WORK_BATCH times in a row before switching to another CPU.
Fixes: 0e87e58bf6 ("blk-mq: improve warning for running a queue on the wrong CPU")
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For blk-mq, ->nr_requests does track queue depth, at least at init
time. But for the older queue paths, it's simply a soft setting.
On top of that, it's generally larger than the hardware setting
on purpose, to allow backup of requests for merging.
Fill a hole in struct request with a 'queue_depth' member, that
drivers can call to more closely inform the block layer of the
real queue depth.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
This is corresponding part for blk-mq. Disk with multiple hardware
queues doesn't need this as we only hold 1 request at most.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently block plug holds up to 16 non-mergeable requests. This makes
sense if the request size is small, eg, reduce lock contention. But if
request size is big enough, we don't need to worry about lock
contention. Holding such request makes no sense and it lows the disk
utilization.
In practice, this improves 10% throughput for my raid5 sequential write
workload.
The size (128k) is arbitrary right now, but it makes sure lock
contention is small. This probably could be more intelligent, eg, check
average request size holded. Since this is mainly for sequential IO,
probably not worthy.
V2: check the last request instead of the first request, so as long as
there is one big size request we flush the plug.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
bsg_validate_sgv4_hdr() doesn't care about the request_queue, so drop it
from it's arguments.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most blk_mq_requeue_request() and blk_mq_add_to_requeue_list() calls
are followed by kicking the requeue list. Hence add an argument to
these two functions that allows to kick the requeue list. This was
proposed by Christoph Hellwig.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_quiesce_queue() waits until ongoing .queue_rq() invocations
have finished. This function does *not* wait until all outstanding
requests have finished (this means invocation of request.end_io()).
The algorithm used by blk_mq_quiesce_queue() is as follows:
* Hold either an RCU read lock or an SRCU read lock around
.queue_rq() calls. The former is used if .queue_rq() does not
block and the latter if .queue_rq() may block.
* blk_mq_quiesce_queue() first calls blk_mq_stop_hw_queues()
followed by synchronize_srcu() or synchronize_rcu(). The latter
call waits for .queue_rq() invocations that started before
blk_mq_quiesce_queue() was called.
* The blk_mq_hctx_stopped() calls that control whether or not
.queue_rq() will be called are called with the (S)RCU read lock
held. This is necessary to avoid race conditions against
blk_mq_quiesce_queue().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() no longer restarts stopped queues
canceling requeue work is no longer needed to prevent that a
stopped queue would be restarted. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() starts stopped queues and since
execution of this function can be scheduled after a queue has
been stopped it is not possible to stop queues without using
an additional state variable to track whether or not the queue
has been stopped. Hence modify blk_mq_requeue_work() such that it
does not start stopped queues. My conclusion after a review of
the blk_mq_stop_hw_queues() and blk_mq_{delay_,}kick_requeue_list()
callers is as follows:
* In the dm driver starting and stopping queues should only happen
if __dm_suspend() or __dm_resume() is called and not if the
requeue list is processed.
* In the SCSI core queue stopping and starting should only be
performed by the scsi_internal_device_block() and
scsi_internal_device_unblock() functions but not by any other
function. Although the blk_mq_stop_hw_queue() call in
scsi_queue_rq() may help to reduce CPU load if a LLD queue is
full, figuring out whether or not a queue should be restarted
when requeueing a command would require to introduce additional
locking in scsi_mq_requeue_cmd() to avoid a race with
scsi_internal_device_block(). Avoid this complexity by removing
the blk_mq_stop_hw_queue() call from scsi_queue_rq().
* In the NVMe core only the functions that call
blk_mq_start_stopped_hw_queues() explicitly should start stopped
queues.
* A blk_mq_start_stopped_hwqueues() call must be added in the
xen-blkfront driver in its blkif_recover() function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Move the "hctx stopped" test and the insert request calls into
blk_mq_direct_issue_request(). Rename that function into
blk_mq_try_issue_directly() to reflect its new semantics. Pass
the hctx pointer to that function instead of looking it up a
second time. These changes avoid that code has to be duplicated
in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The function blk_queue_stopped() allows to test whether or not a
traditional request queue has been stopped. Introduce a helper
function that allows block drivers to query easily whether or not
one or more hardware contexts of a blk-mq queue have been stopped.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Multiple functions test the BLK_MQ_S_STOPPED bit so introduce
a helper function that performs this test.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The meaning of the BLK_MQ_S_STOPPED flag is "do not call
.queue_rq()". Hence modify blk_mq_make_request() such that requests
are queued instead of issued if a queue has been stopped.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is a helper that pins down a range from an iov_iter and adds it to
a bio without requiring a separate memory allocation for the page array.
It will be used for upcoming direct I/O implementations for block devices
and iomap based file systems.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[hch: ported to the iov_iter interface, renamed and added comments.
All blame should be directed to me and all fame should go to Kent
after this!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the WRITE_* and READ_SYNC wrappers, and just use the flags
directly. Where applicable this also drops usage of the
bio_set_op_attrs wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Noidle should be the default for writes as seen by all the compounds
definitions in fs.h using it. In fact only direct I/O really should
be using NODILE, so turn the whole flag around to get the defaults
right, which will make our life much easier especially onces the
WRITE_* defines go away.
This assumes all the existing "raw" users of REQ_SYNC for writes
want noidle behavior, which seems to be spot on from a quick audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we don't need the common flags to overflow outside the range
of a 32-bit type we can encode them the same way for both the bio and
request fields. This in addition allows us to place the operation
first (and make some room for more ops while we're at it) and to
stop having to shift around the operation values.
In addition this allows passing around only one value in the block layer
instead of two (and eventuall also in the file systems, but we can do
that later) and thus clean up a lot of code.
Last but not least this allows decreasing the size of the cmd_flags
field in struct request to 32-bits. Various functions passing this
value could also be updated, but I'd like to avoid the churn for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's the last bio-only REQ_* flag, and we have space for it in the bio
bi_flags field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
With the addition of the zoned operations the tests in this function
became incorrect. But I think it's much better to just open code the
allow operations in the only caller anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can just use struct blk_mq_alloc_data - it has a few more
members, but we allocate it further down the stack anyway. So
this cleans up the code, and reduces the stack overhead a bit.
Signed-off-by: Jens Axboe <axboe@fb.com>
If we end up sleeping due to running out of requests, we should
update the hardware and software queues in the map ctx structure.
Otherwise we could end up having rq->mq_ctx point to the pre-sleep
context, and risk corrupting ctx->rq_list since we'll be
grabbing the wrong lock when inserting the request.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Chris Mason <clm@fb.com>
Fixes: 63581af3f3 ("blk-mq: remove non-blocking pass in blk_mq_map_request")
Signed-off-by: Jens Axboe <axboe@fb.com>
If we end up sleeping due to running out of requests, we should
update the hardware and software queues in the map ctx structure.
Otherwise we could end up having rq->mq_ctx point to the pre-sleep
context, and risk corrupting ctx->rq_list since we'll be
grabbing the wrong lock when inserting the request.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Chris Mason <clm@fb.com>
Fixes: 63581af3f3 ("blk-mq: remove non-blocking pass in blk_mq_map_request")
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes one issue reported by Kent, which can
be triggered in bcachefs over sata disk. Actually it
is a generic issue in block flush vs. blk-tag.
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The blkdev_report_zones produces a harmless warning when
-Wmaybe-uninitialized is set, after gcc gets a little confused
about the multiple 'goto' here:
block/blk-zoned.c: In function 'blkdev_report_zones':
block/blk-zoned.c:188:13: error: 'nz' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Moving the assignment to nr_zones makes this a little simpler
while also avoiding the warning reliably. I'm removing the
extraneous initialization of 'int ret' in the same patch, as
that is semi-related and could cause an uninitialized use of
that variable to not produce a warning.
Fixes: 6a0cb1bc10 ("block: Implement support for zoned block devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When bandblocks_set acknowledges a range or badblocks_clear a range,
it's possible all badblocks are acknowledged. We should update
unacked_exist if this occurs.
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Tested-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
"A set of fixes that missed the merge window, mostly due to me being
away around that time.
Nothing major here, a mix of nvme cleanups and fixes, and one fix for
the badblocks handling"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: use symbolic constants for CNS values
nvme: use symbolic constants for CNS values
nvme.h: add an enum for cns values
nvme.h: don't use uuid_be
nvme.h: resync with nvme-cli
nvme: Add tertiary number to NVME_VS
nvme : Add sysfs entry for NVMe CMBs when appropriate
nvme: don't schedule multiple resets
nvme: Delete created IO queues on reset
nvme: Stop probing a removed device
badblocks: fix overlapping check for clearing
Patch adds an association between iocontext ioprio and the ioprio of a
request. This is done to enable request based drivers the ability to
act on priority information stored in the request. An example being
ATA devices that support command priorities. If the ATA driver discovers
that the device supports command priorities and the request has valid
priority information indicating the request is high priority, then a high
priority command can be sent to the device. This should improve tail
latencies for high priority IO on any device that queues requests
internally and can make use of the priority information stored in the
request.
The ioprio of the request is set in blk_rq_set_prio which takes the
request and the ioc as arguments. If the ioc is valid in blk_rq_set_prio
then the iopriority of the request is set as the iopriority of the ioc.
In init_request_from_bio a check is made to see if the ioprio of the bio
is valid and if so then the request prio comes from the bio.
Signed-off-by: Adam Manzananares <adam.manzanares@wdc.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Adds the new BLKREPORTZONE and BLKRESETZONE ioctls for respectively
obtaining the zone configuration of a zoned block device and resetting
the write pointer of sequential zones of a zoned block device.
The BLKREPORTZONE ioctl maps directly to a single call of the function
blkdev_report_zones. The zone information result is passed as an array
of struct blk_zone identical to the structure used internally for
processing the REQ_OP_ZONE_REPORT operation. The BLKRESETZONE ioctl
maps to a single call of the blkdev_reset_zones function.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Implement zoned block device zone information reporting and reset.
Zone information are reported as struct blk_zone. This implementation
does not differentiate between host-aware and host-managed device
models and is valid for both. Two functions are provided:
blkdev_report_zones for discovering the zone configuration of a
zoned block device, and blkdev_reset_zones for resetting the write
pointer of sequential zones. The helper function blk_queue_zone_size
and bdev_zone_size are also provided for, as the name suggest,
obtaining the zone size (in 512B sectors) of the zones of the device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: * Removed the zone cache
* Implement report zones operation based on earlier proposal
by Shaun Tancheff <shaun.tancheff@seagate.com>]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Define REQ_OP_ZONE_REPORT and REQ_OP_ZONE_RESET for handling zones of
host-managed and host-aware zoned block devices. With with these two
new operations, the total number of operations defined reaches 8 and
still fits with the 3 bits definition of REQ_OP_BITS.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The queue limits already have a 'chunk_sectors' setting, so
we should be presenting it via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: Updated Documentation/ABI/testing/sysfs-block]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add the zoned queue limit to indicate the zoning model of a block device.
Defined values are 0 (BLK_ZONED_NONE) for regular block devices,
1 (BLK_ZONED_HA) for host-aware zone block devices and 2 (BLK_ZONED_HM)
for host-managed zone block devices. The standards defined drive managed
model is not defined here since these block devices do not provide any
command for accessing zone information. Drive managed model devices will
be reported as BLK_ZONED_NONE.
The helper functions blk_queue_zoned_model and bdev_zoned_model return
the zoned limit and the functions blk_queue_is_zoned and bdev_is_zoned
return a boolean for callers to test if a block device is zoned.
The zoned attribute is also exported as a string to applications via
sysfs. BLK_ZONED_NONE shows as "none", BLK_ZONED_HA as "host-aware" and
BLK_ZONED_HM as "host-managed".
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
extract as much possible uncertainty from a running system at boot time as
possible, hoping to capitalize on any possible variation in CPU operation
(due to runtime data differences, hardware differences, SMP ordering,
thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example for
how to manipulate kernel code using the gcc plugin internals.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=1dUK
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
Pull cgroup updates from Tejun Heo:
- tracepoints for basic cgroup management operations added
- kernfs and cgroup path formatting functions updated to behave in the
style of strlcpy()
- non-critical bug fixes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
blkcg: Unlock blkcg_pol_mutex only once when cpd == NULL
cgroup: fix error handling regressions in proc_cgroup_show() and cgroup_release_agent()
cpuset: fix error handling regression in proc_cpuset_show()
cgroup: add tracepoints for basic operations
cgroup: make cgroup_path() and friends behave in the style of strlcpy()
kernfs: remove kernfs_path_len()
kernfs: make kernfs_path*() behave in the style of strlcpy()
kernfs: add dummy implementation of kernfs_path_from_node()
Current bad block clear implementation assumes the range to clear
overlaps with at least one bad block already stored. If given range to
clear precedes first bad block in a list, the first entry is incorrectly
updated.
Check not only if stored block end is past clear block end but also if
stored block start is before clear block end.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Make sure that the offset and length arguments that we're using to
construct WRITE SAME and DISCARD requests are actually aligned to the
logical block size. Failure to do this causes other errors in other parts
of the block layer or the SCSI layer because disks don't support partial
logical block writes.
Link: http://lkml.kernel.org/r/147518379026.22791.4437508871355153928.stgit@birch.djwong.org
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mike Snitzer <snitzer@redhat.com> # tweaked header
Cc: Brian Foster <bfoster@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "fallocate for block devices", v11.
This is a patchset to fix page cache coherency with BLKZEROOUT and
implement fallocate for block devices.
The first patch is a fix to the existing BLKZEROOUT ioctl to invalidate
the page cache if the zeroing command to the underlying device succeeds.
Without this patch we still have the pagecache coherence bug that's been
in the kernel forever.
The second patch changes the internal block device functions to reject
attempts to discard or zeroout that are not aligned to the logical block
size. Previously, we only checked that the start/len parameters were
512-byte aligned, which caused kernel BUG_ONs for unaligned IOs to 4k-LBA
devices.
The third patch creates an fallocate handler for block devices, wires up
the FALLOC_FL_PUNCH_HOLE flag to zeroing-discard, and connects
FALLOC_FL_ZERO_RANGE to write-same so that we can have a consistent
fallocate interface between files and block devices. It also allows the
combination of PUNCH_HOLE and NO_HIDE_STALE to invoke non-zeroing discard.
Test cases for the new block device fallocate are now in xfstests as
generic/349-351.
This patch (of 3):
Invalidate the page cache (as a regular O_DIRECT write would do) to avoid
returning stale cache contents at a later time.
Link: http://lkml.kernel.org/r/147518378313.22791.16649519283678515021.stgit@birch.djwong.org
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Brian Foster <bfoster@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The __latent_entropy gcc attribute can be used only on functions and
variables. If it is on a function then the plugin will instrument it for
gathering control-flow entropy. If the attribute is on a variable then
the plugin will initialize it with random contents. The variable must
be an integer, an integer array type or a structure with integer fields.
These specific functions have been selected because they are init
functions (to help gather boot-time entropy), are called at unpredictable
times, or they have variable loops, each of which provide some level of
latent entropy.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: expanded commit message]
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull blk-mq CPU hotplug update from Jens Axboe:
"This is the conversion of blk-mq to the new hotplug state machine"
* 'for-4.9/block-smp' of git://git.kernel.dk/linux-block:
blk-mq: fixup "Convert to new hotplug state machine"
blk-mq: Convert to new hotplug state machine
blk-mq/cpu-notif: Convert to new hotplug state machine
Pull blk-mq irq/cpu mapping updates from Jens Axboe:
"This is the block-irq topic branch for 4.9-rc. It's mostly from
Christoph, and it allows drivers to specify their own mappings, and
more importantly, to share the blk-mq mappings with the IRQ affinity
mappings. It's a good step towards making this work better out of the
box"
* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
blk_mq: linux/blk-mq.h does not include all the headers it depends on
blk-mq: kill unused blk_mq_create_mq_map()
blk-mq: get rid of the cpumask in struct blk_mq_tags
nvme: remove the post_scan callout
nvme: switch to use pci_alloc_irq_vectors
blk-mq: provide a default queue mapping for PCI device
blk-mq: allow the driver to pass in a queue mapping
blk-mq: remove ->map_queue
blk-mq: only allocate a single mq_map per tag_set
blk-mq: don't redistribute hardware queues on a CPU hotplug event
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Unlocking a mutex twice is wrong. Hence modify blkcg_policy_register()
such that blkcg_pol_mutex is unlocked once if cpd == NULL. This patch
avoids that smatch reports the following error:
block/blk-cgroup.c:1378: blkcg_policy_register() error: double unlock 'mutex:&blkcg_pol_mutex'
Fixes: 06b285bd11 ("blkcg: fix blkcg_policy_data allocation bug")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Tejun Heo <tj@kernel.org>
This provides the caller a feedback that a given hctx is not mapped and thus
no command can be sent on it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
While debugging timeouts happening in my application workload (ScyllaDB), I have
observed calls to open() taking a long time, ranging everywhere from 2 seconds -
the first ones that are enough to time out my application - to more than 30
seconds.
The problem seems to happen because XFS may block on pending metadata updates
under certain circumnstances, and that's confirmed with the following backtrace
taken by the offcputime tool (iovisor/bcc):
ffffffffb90c57b1 finish_task_switch
ffffffffb97dffb5 schedule
ffffffffb97e310c schedule_timeout
ffffffffb97e1f12 __down
ffffffffb90ea821 down
ffffffffc046a9dc xfs_buf_lock
ffffffffc046abfb _xfs_buf_find
ffffffffc046ae4a xfs_buf_get_map
ffffffffc046babd xfs_buf_read_map
ffffffffc0499931 xfs_trans_read_buf_map
ffffffffc044a561 xfs_da_read_buf
ffffffffc0451390 xfs_dir3_leaf_read.constprop.16
ffffffffc0452b90 xfs_dir2_leaf_lookup_int
ffffffffc0452e0f xfs_dir2_leaf_lookup
ffffffffc044d9d3 xfs_dir_lookup
ffffffffc047d1d9 xfs_lookup
ffffffffc0479e53 xfs_vn_lookup
ffffffffb925347a path_openat
ffffffffb9254a71 do_filp_open
ffffffffb9242a94 do_sys_open
ffffffffb9242b9e sys_open
ffffffffb97e42b2 entry_SYSCALL_64_fastpath
00007fb0698162ed [unknown]
Inspecting my run with blktrace, I can see that the xfsaild kthread exhibit very
high "Dispatch wait" times, on the dozens of seconds range and consistent with
the open() times I have saw in that run.
Still from the blktrace output, we can after searching a bit, identify the
request that wasn't dispatched:
8,0 11 152 81.092472813 804 A WM 141698288 + 8 <- (8,1) 141696240
8,0 11 153 81.092472889 804 Q WM 141698288 + 8 [xfsaild/sda1]
8,0 11 154 81.092473207 804 G WM 141698288 + 8 [xfsaild/sda1]
8,0 11 206 81.092496118 804 I WM 141698288 + 8 ( 22911) [xfsaild/sda1]
<==== 'I' means Inserted (into the IO scheduler) ===================================>
8,0 0 289372 96.718761435 0 D WM 141698288 + 8 (15626265317) [swapper/0]
<==== Only 15s later the CFQ scheduler dispatches the request ======================>
As we can see above, in this particular example CFQ took 15 seconds to dispatch
this request. Going back to the full trace, we can see that the xfsaild queue
had plenty of opportunity to run, and it was selected as the active queue many
times. It would just always be preempted by something else (example):
8,0 1 0 81.117912979 0 m N cfq1618SN / insert_request
8,0 1 0 81.117913419 0 m N cfq1618SN / add_to_rr
8,0 1 0 81.117914044 0 m N cfq1618SN / preempt
8,0 1 0 81.117914398 0 m N cfq767A / slice expired t=1
8,0 1 0 81.117914755 0 m N cfq767A / resid=40
8,0 1 0 81.117915340 0 m N / served: vt=1948520448 min_vt=1948520448
8,0 1 0 81.117915858 0 m N cfq767A / sl_used=1 disp=0 charge=0 iops=1 sect=0
where cfq767 is the xfsaild queue and cfq1618 corresponds to one of the ScyllaDB
IO dispatchers.
The requests preempting the xfsaild queue are synchronous requests. That's a
characteristic of ScyllaDB workloads, as we only ever issue O_DIRECT requests.
While it can be argued that preempting ASYNC requests in favor of SYNC is part
of the CFQ logic, I don't believe that doing so for 15+ seconds is anyone's
goal.
Moreover, unless I am misunderstanding something, that breaks the expectation
set by the "fifo_expire_async" tunable, which in my system is set to the
default.
Looking at the code, it seems to me that the issue is that after we make
an async queue active, there is no guarantee that it will execute any request.
When the queue itself tests if it cfq_may_dispatch() it can bail if it sees SYNC
requests in flight. An incoming request from another queue can also preempt it
in such situation before we have the chance to execute anything (as seen in the
trace above).
This patch sets the must_dispatch flag if we notice that we have requests
that are already fifo_expired. This flag is always cleared after
cfq_dispatch_request() returns from cfq_dispatch_requests(), so it won't pin
the queue for subsequent requests (unless they are themselves expired)
Care is taken during preempt to still allow rt requests to preempt us
regardless.
Testing my workload with this patch applied produces much better results.
From the application side I see no timeouts, and the open() latency histogram
generated by systemtap looks much better, with the worst outlier at 131ms:
Latency histogram of xfs_buf_lock acquisition (microseconds):
value |-------------------------------------------------- count
0 | 11
1 |@@@@ 161
2 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ 1966
4 |@ 54
8 | 36
16 | 7
32 | 0
64 | 0
~
1024 | 0
2048 | 0
4096 | 1
8192 | 1
16384 | 2
32768 | 0
65536 | 0
131072 | 1
262144 | 0
524288 | 0
Signed-off-by: Glauber Costa <glauber@scylladb.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: linux-block@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Glauber Costa <glauber@scylladb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The "blk_mq_queue_reinit_dead()" just cleared the cpumask instead doing
a copy. Since we might never had an online callback we could end up with
a ZERO mask which in turn leads to crash as test robot demonstarted.
Fixes: 65d5291eee ("blk-mq: Convert to new hotplug state machine")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a driver sets BLK_MQ_F_BLOCKING, it is allowed to block in its
->queue_rq() handler. For that case, blk-mq ensures that we always
calls it from a safe context.
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-by: Josef Bacik <jbacik@fb.com>
bt_get already does a non-blocking pass as well as running the queue
when scheduling internally, no need to duplicate it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Two cases:
1) blk_mq_alloc_request() needlessly re-runs the queue, after
calling into the tag allocation without NOWAIT set. We don't
need to do that.
2) blk_mq_map_request() should just use blk_mq_run_hw_queue() with
the async flag set to false.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Install the callbacks via the state machine so we can phase out the cpu
hotplug notifiers mess.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-block@vger.kernel.org
Cc: rt@linutronix.de
Cc: Christoph Hellwing <hch@lst.de>
Link: http://lkml.kernel.org/r/20160919212601.180033814@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Replace the block-mq notifier list management with the multi instance
facility in the cpu hotplug state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-block@vger.kernel.org
Cc: rt@linutronix.de
Cc: Christoph Hellwing <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
bio_free_pages is introduced in commit 1dfa0f68c0
("block: add a helper to free bio bounce buffer pages"),
we can reuse the func in other modules after it was
imported.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Enable devices without a gendisk instance to register itself with blk-mq
and expose the associated multi-queue sysfs entries.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Right now, if slice is expired, we start a new slice. If a bio is
queued, we keep on extending slice by throtle_slice interval (100ms).
This worked well as long as pending timer function got executed with-in
few milli seconds of scheduled time. But looks like with recent changes
in timer subsystem, slack can be much longer depending on the expiry time
of the scheduled timer.
commit 500462a9de ("timers: Switch to a non-cascading wheel")
This means, by the time timer function gets executed, it is possible the
delay from scheduled time is more than 100ms. That means current code
will conclude that existing slice has expired and a new one needs to
be started. New slice will be 100ms by default and that will not be
sufficient to meet rate requirement of group given the bio size and
bio will not be dispatched and we will start a new timer function to
wait. And when that timer expires, same process will repeat and we
will wait again and this can easily be an infinite loop.
Solve this issue by starting a new slice only if throttle gropup is
empty. If it is not empty, that means there should be an active slice
going on. Ideally it should not be expired but given the slack, it is
possible that it has expired.
Reported-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
and building block/blk-mq-pci.o should depend on CONFIG_BLOCK
Fixes: 973c4e372c ("blk-mq: provide a default queue mapping for PCI device")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to get good cache behavior from a sbitmap, we want each CPU to
stick to its own cacheline(s) as much as possible. This might happen
naturally as the bitmap gets filled up and the alloc_hint values spread
out, but we really want this behavior from the start. blk-mq apparently
intended to do this, but the code to do this was never wired up. Get rid
of the dead code and make it part of the sbitmap library.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Again, there's no point in passing this in every time. Make it part of
struct sbitmap_queue and clean up the API.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allocating your own per-cpu allocation hint separately makes for an
awkward API. Instead, allocate the per-cpu hint as part of the struct
sbitmap_queue. There's no point for a struct sbitmap_queue without the
cache, but you can still use a bare struct sbitmap.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is a generally useful data structure, so make it available to
anyone else who might want to use it. It's also a nice cleanup
separating the allocation logic from the rest of the tag handling logic.
The code is behind a new Kconfig option, CONFIG_SBITMAP, which is only
selected by CONFIG_BLOCK for now.
This should be a complete noop functionality-wise.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently account a '0' dispatch, and anything above that still falls
below the range set by BLK_MQ_MAX_DISPATCH_ORDER. If we dispatch more,
we don't account it.
Change the last bucket to be inclusive of anything above the range we
track, and have the sysfs file reflect that by including a '+' in the
output:
$ cat /sys/block/nvme0n1/mq/0/dispatched
0 1006
1 20229
2 1
4 0
8 0
16 0
32+ 0
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Unused now that NVMe sets up irq affinity before calling into blk-mq.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This allows drivers specify their own queue mapping by overriding the
setup-time function that builds the mq_map. This can be used for
example to build the map based on the MSI-X vector mapping provided
by the core interrupt layer for PCI devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
All drivers use the default, so provide an inline version of it. If we
ever need other queue mapping we can add an optional method back,
although supporting will also require major changes to the queue setup
code.
This provides better code generation, and better debugability as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The mapping is identical for all queues in a tag_set, so stop wasting
memory for building multiple. Note that for now I've kept the mq_map
pointer in the request_queue, but we'll need to investigate if we can
remove it without suffering too much from the additional pointer chasing.
The same would apply to the mq_ops pointer as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently blk-mq will totally remap hardware context when a CPU hotplug
even happened, which causes major havoc for drivers, as they are never
told about this remapping. E.g. any carefully sorted out CPU affinity
will just be completely messed up.
The rebuild also doesn't really help for the common case of cpu
hotplug, which is soft onlining / offlining of cpus - in this case we
should just leave the queue and irq mapping as is. If it actually
worked it would have helped in the case of physical cpu hotplug,
although for that we'd need a way to actually notify the driver.
Note that drivers may already be able to accommodate such a topology
change on their own, e.g. using the reset_controller sysfs file in NVMe
will cause the driver to get things right for this case.
With the rebuild removed we will simplify retain the queue mapping for
a soft offlined CPU that will work when it comes back online, and will
map any newly onlined CPU to queue 0 until the driver initiates
a rebuild of the queue map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_delay_kick_requeue_list() provides the ability to kick the
q->requeue_list after a specified time. To do this the request_queue's
'requeue_work' member was changed to a delayed_work.
blk_mq_delay_kick_requeue_list() allows DM to defer processing requeued
requests while it doesn't make sense to immediately requeue them
(e.g. when all paths in a DM multipath have failed).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
commit e1defc4ff0
"block: Do away with the notion of hardsect_size"
removed the notion of "hardware sector size" from
the kernel in favor of logical block size, but
references remain in comments and documentation.
Update the remaining sites mentioning hardsect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow the io_poll statistics to be zeroed to make for easier logging
of polling event.
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to help determine the effectiveness of polling in a running
system it is usful to determine the ratio of how often the poll
function is called vs how often the completion is checked. For this
reason we add a poll_considered variable and add it to the sysfs entry
for io_poll.
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When drivers or the core calls this function, they usually
dereference the request shortly there after. Prefetch the first
cache line.
Profiling IO workloads shows that this is the most common cache
miss on the block side of things.
Signed-off-by: Jens Axboe <axboe@fb.com>
__blk_mq_run_hw_queue() currently warns if we are running the queue on a
CPU that isn't set in its mask. However, this can happen if a CPU is
being offlined, and the workqueue handling will place the work on CPU0
instead. Improve the warning so that it only triggers if the batch cpu
in the hardware queue is currently online. If it triggers for that
case, then it's indicative of a flow problem in blk-mq, so we want to
retain it for that case.
Signed-off-by: Jens Axboe <axboe@fb.com>
We do this in a few places, if the CPU is offline. This isn't allowed,
though, since on multi queue hardware, we can't just move a request
from one software queue to another, if they map to different hardware
queues. The request and tag isn't valid on another hardware queue.
This can happen if plugging races with CPU offlining. But it does
no harm, since it can only happen in the window where we are
currently busy freezing the queue and flushing IO, in preparation
for redoing the software <-> hardware queue mappings.
Signed-off-by: Jens Axboe <axboe@fb.com>
After arbitrary bio size was introduced, the incoming bio may
be very big. We have to split the bio into small bios so that
each holds at most BIO_MAX_PAGES bvecs for safety reason, such
as bio_clone().
This patch fixes the following kernel crash:
> [ 172.660142] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
> [ 172.660229] IP: [<ffffffff811e53b4>] bio_trim+0xf/0x2a
> [ 172.660289] PGD 7faf3e067 PUD 7f9279067 PMD 0
> [ 172.660399] Oops: 0000 [#1] SMP
> [...]
> [ 172.664780] Call Trace:
> [ 172.664813] [<ffffffffa007f3be>] ? raid1_make_request+0x2e8/0xad7 [raid1]
> [ 172.664846] [<ffffffff811f07da>] ? blk_queue_split+0x377/0x3d4
> [ 172.664880] [<ffffffffa005fb5f>] ? md_make_request+0xf6/0x1e9 [md_mod]
> [ 172.664912] [<ffffffff811eb860>] ? generic_make_request+0xb5/0x155
> [ 172.664947] [<ffffffffa0445c89>] ? prio_io+0x85/0x95 [bcache]
> [ 172.664981] [<ffffffffa0448252>] ? register_cache_set+0x355/0x8d0 [bcache]
> [ 172.665016] [<ffffffffa04497d3>] ? register_bcache+0x1006/0x1174 [bcache]
The issue can be reproduced by the following steps:
- create one raid1 over two virtio-blk
- build bcache device over the above raid1 and another cache device
and bucket size is set as 2Mbytes
- set cache mode as writeback
- run random write over ext4 on the bcache device
Fixes: 54efd50(block: make generic_make_request handle arbitrarily sized bios)
Reported-by: Sebastian Roesner <sroesner-kernelorg@roesner-online.de>
Reported-by: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: stable@vger.kernel.org (4.3+)
Cc: Shaohua Li <shli@fb.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_set_queue_dying() can be called while another thread is
submitting I/O or changing queue flags, e.g. through dm_stop_queue().
Hence protect the QUEUE_FLAG_DYING flag change with locking.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 288dab8a35 ("block: add a separate operation type for secure
erase") split REQ_OP_SECURE_ERASE from REQ_OP_DISCARD without considering
all the places REQ_OP_DISCARD was being used to mean either. Fix those.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 288dab8a35 ("block: add a separate operation type for secure erase")
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
If we fail registering any of the hardware queues, we call
into blk_mq_unregister_disk() with the hotplug mutex already
held. Since blk_mq_unregister_disk() attempts to acquire the
same mutex, we end up in a less than happy place.
Reported-by: Jinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The name for a bdi of a gendisk is derived from the gendisk's devt.
However, since the gendisk is destroyed before the bdi it leaves a
window where a new gendisk could dynamically reuse the same devt while a
bdi with the same name is still live. Arrange for the bdi to hold a
reference against its "owner" disk device while it is registered.
Otherwise we can hit sysfs duplicate name collisions like the following:
WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80
sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1'
Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015
0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec
ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351
0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8
Call Trace:
[<ffffffff8134caec>] dump_stack+0x63/0x87
[<ffffffff8108c351>] __warn+0xd1/0xf0
[<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80
[<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80
[<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90
[<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320
[<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0
[<ffffffff8134ff55>] kobject_add+0x75/0xd0
[<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f
[<ffffffff8148b0a5>] device_add+0x125/0x610
[<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100
[<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20
[<ffffffff811b775c>] bdi_register+0x8c/0x180
[<ffffffff811b7877>] bdi_register_dev+0x27/0x30
[<ffffffff813317f5>] add_disk+0x175/0x4a0
Cc: <stable@vger.kernel.org>
Reported-by: Yi Zhang <yizhan@redhat.com>
Tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixed up missing 0 return in bdi_register_owner().
Signed-off-by: Jens Axboe <axboe@fb.com>
In case a submitted request gets stuck for some reason, the block layer
can prevent the request starvation by starting the scheduled timeout work.
If this stuck request occurs at the same time another thread has started
a queue freeze, the blk_mq_timeout_work will not be able to acquire the
queue reference and will return silently, thus not issuing the timeout.
But since the request is already holding a q_usage_counter reference and
is unable to complete, it will never release its reference, preventing
the queue from completing the freeze started by first thread. This puts
the request_queue in a hung state, forever waiting for the freeze
completion.
This was observed while running IO to a NVMe device at the same time we
toggled the CPU hotplug code. Eventually, once a request got stuck
requiring a timeout during a queue freeze, we saw the CPU Hotplug
notification code get stuck inside blk_mq_freeze_queue_wait, as shown in
the trace below.
[c000000deaf13690] [c000000deaf13738] 0xc000000deaf13738 (unreliable)
[c000000deaf13860] [c000000000015ce8] __switch_to+0x1f8/0x350
[c000000deaf138b0] [c000000000ade0e4] __schedule+0x314/0x990
[c000000deaf13940] [c000000000ade7a8] schedule+0x48/0xc0
[c000000deaf13970] [c0000000005492a4] blk_mq_freeze_queue_wait+0x74/0x110
[c000000deaf139e0] [c00000000054b6a8] blk_mq_queue_reinit_notify+0x1a8/0x2e0
[c000000deaf13a40] [c0000000000e7878] notifier_call_chain+0x98/0x100
[c000000deaf13a90] [c0000000000b8e08] cpu_notify_nofail+0x48/0xa0
[c000000deaf13ac0] [c0000000000b92f0] _cpu_down+0x2a0/0x400
[c000000deaf13b90] [c0000000000b94a8] cpu_down+0x58/0xa0
[c000000deaf13bc0] [c0000000006d5dcc] cpu_subsys_offline+0x2c/0x50
[c000000deaf13bf0] [c0000000006cd244] device_offline+0x104/0x140
[c000000deaf13c30] [c0000000006cd40c] online_store+0x6c/0xc0
[c000000deaf13c80] [c0000000006c8c78] dev_attr_store+0x68/0xa0
[c000000deaf13cc0] [c0000000003974d0] sysfs_kf_write+0x80/0xb0
[c000000deaf13d00] [c0000000003963e8] kernfs_fop_write+0x188/0x200
[c000000deaf13d50] [c0000000002e0f6c] __vfs_write+0x6c/0xe0
[c000000deaf13d90] [c0000000002e1ca0] vfs_write+0xc0/0x230
[c000000deaf13de0] [c0000000002e2cdc] SyS_write+0x6c/0x110
[c000000deaf13e30] [c000000000009204] system_call+0x38/0xb4
The fix is to allow the timeout work to execute in the window between
dropping the initial refcount reference and the release of the last
reference, which actually marks the freeze completion. This can be
achieved with percpu_refcount_tryget, which does not require the counter
to be alive. This way the timeout work can do it's job and terminate a
stuck request even during a freeze, returning its reference and avoiding
the deadlock.
Allowing the timeout to run is just a part of the fix, since for some
devices, we might get stuck again inside the device driver's timeout
handler, should it attempt to allocate a new request in that path -
which is a quite common action for Abort commands, which need to be sent
after a timeout. In NVMe, for instance, we call blk_mq_alloc_request
from inside the timeout handler, which will fail during a freeze, since
it also tries to acquire a queue reference.
I considered a similar change to blk_mq_alloc_request as a generic
solution for further device driver hangs, but we can't do that, since it
would allow new requests to disturb the freeze process. I thought about
creating a new function in the block layer to support unfreezable
requests for these occasions, but after working on it for a while, I
feel like this should be handled in a per-driver basis. I'm now
experimenting with changes to the NVMe timeout path, but I'm open to
suggestions of ways to make this generic.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: linux-nvme@lists.infradead.org
Cc: linux-block@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
I got a KASAN report of use-after-free:
==================================================================
BUG: KASAN: use-after-free in klist_iter_exit+0x61/0x70 at addr ffff8800b6581508
Read of size 8 by task trinity-c1/315
=============================================================================
BUG kmalloc-32 (Not tainted): kasan: bad access detected
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in disk_seqf_start+0x66/0x110 age=144 cpu=1 pid=315
___slab_alloc+0x4f1/0x520
__slab_alloc.isra.58+0x56/0x80
kmem_cache_alloc_trace+0x260/0x2a0
disk_seqf_start+0x66/0x110
traverse+0x176/0x860
seq_read+0x7e3/0x11a0
proc_reg_read+0xbc/0x180
do_loop_readv_writev+0x134/0x210
do_readv_writev+0x565/0x660
vfs_readv+0x67/0xa0
do_preadv+0x126/0x170
SyS_preadv+0xc/0x10
do_syscall_64+0x1a1/0x460
return_from_SYSCALL_64+0x0/0x6a
INFO: Freed in disk_seqf_stop+0x42/0x50 age=160 cpu=1 pid=315
__slab_free+0x17a/0x2c0
kfree+0x20a/0x220
disk_seqf_stop+0x42/0x50
traverse+0x3b5/0x860
seq_read+0x7e3/0x11a0
proc_reg_read+0xbc/0x180
do_loop_readv_writev+0x134/0x210
do_readv_writev+0x565/0x660
vfs_readv+0x67/0xa0
do_preadv+0x126/0x170
SyS_preadv+0xc/0x10
do_syscall_64+0x1a1/0x460
return_from_SYSCALL_64+0x0/0x6a
CPU: 1 PID: 315 Comm: trinity-c1 Tainted: G B 4.7.0+ #62
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
ffffea0002d96000 ffff880119b9f918 ffffffff81d6ce81 ffff88011a804480
ffff8800b6581500 ffff880119b9f948 ffffffff8146c7bd ffff88011a804480
ffffea0002d96000 ffff8800b6581500 fffffffffffffff4 ffff880119b9f970
Call Trace:
[<ffffffff81d6ce81>] dump_stack+0x65/0x84
[<ffffffff8146c7bd>] print_trailer+0x10d/0x1a0
[<ffffffff814704ff>] object_err+0x2f/0x40
[<ffffffff814754d1>] kasan_report_error+0x221/0x520
[<ffffffff8147590e>] __asan_report_load8_noabort+0x3e/0x40
[<ffffffff83888161>] klist_iter_exit+0x61/0x70
[<ffffffff82404389>] class_dev_iter_exit+0x9/0x10
[<ffffffff81d2e8ea>] disk_seqf_stop+0x3a/0x50
[<ffffffff8151f812>] seq_read+0x4b2/0x11a0
[<ffffffff815f8fdc>] proc_reg_read+0xbc/0x180
[<ffffffff814b24e4>] do_loop_readv_writev+0x134/0x210
[<ffffffff814b4c45>] do_readv_writev+0x565/0x660
[<ffffffff814b8a17>] vfs_readv+0x67/0xa0
[<ffffffff814b8de6>] do_preadv+0x126/0x170
[<ffffffff814b92ec>] SyS_preadv+0xc/0x10
This problem can occur in the following situation:
open()
- pread()
- .seq_start()
- iter = kmalloc() // succeeds
- seqf->private = iter
- .seq_stop()
- kfree(seqf->private)
- pread()
- .seq_start()
- iter = kmalloc() // fails
- .seq_stop()
- class_dev_iter_exit(seqf->private) // boom! old pointer
As the comment in disk_seqf_stop() says, stop is called even if start
failed, so we need to reinitialise the private pointer to NULL when seq
iteration stops.
An alternative would be to set the private pointer to NULL when the
kmalloc() in disk_seqf_start() fails.
Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a bio is cloned, the newly created bio must be associated with
the same blkcg as the original bio (if BLK_CGROUP is enabled). If
this operation is not performed, then the new bio is not associated
with any group, and the group of the current task is returned when
the group of the bio is requested.
Depending on the cloning frequency, this may cause a large
percentage of the bios belonging to a given group to be treated
as if belonging to other groups (in most cases as if belonging to
the root group). The expected group isolation may thereby be broken.
This commit adds the missing association in bio-cloning functions.
Fixes: da2f0f74cf ("Btrfs: add support for blkio controllers")
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
'nr_undestroyed_grps' in struct throtl_data was used to count
the number of throtl_grp related with throtl_data, but now
throtl_grp is tracked by blkcg_gq, so it is useless anymore.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The functionality for block device DAX was already removed with commit
acc93d30d7 ("Revert "block: enable dax for raw block devices"")
However, we still had a config option hanging around that was always
disabled because it depended on CONFIG_BROKEN. This config option was
introduced in commit 03cdadb040 ("block: disable block device DAX by
default")
This change reverts that commit, removing the dead config option.
Link: http://lkml.kernel.org/r/20160729182314.6368-1-ross.zwisler@linux.intel.com
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
For a front merge, the maximum number of sectors of the
request must be checked against the front merge BIO sector,
not the current sector of the request.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Before merging a bio into an existing request, io scheduler is called to
get its approval first. However, the requests that come from a plug
flush may get merged by block layer without consulting with io
scheduler.
In case of CFQ, this can cause fairness problems. For instance, if a
request gets merged into a low weight cgroup's request, high weight cgroup
now will depend on low weight cgroup to get scheduled. If high weigt cgroup
needs that io request to complete before submitting more requests, then it
will also lose its timeslice.
Following script demonstrates the problem. Group g1 has a low weight, g2
and g3 have equal high weights but g2's requests are adjacent to g1's
requests so they are subject to merging. Due to these merges, g2 gets
poor disk time allocation.
cat > cfq-merge-repro.sh << "EOF"
#!/bin/bash
set -e
IO_ROOT=/mnt-cgroup/io
mkdir -p $IO_ROOT
if ! mount | grep -qw $IO_ROOT; then
mount -t cgroup none -oblkio $IO_ROOT
fi
cd $IO_ROOT
for i in g1 g2 g3; do
if [ -d $i ]; then
rmdir $i
fi
done
mkdir g1 && echo 10 > g1/blkio.weight
mkdir g2 && echo 495 > g2/blkio.weight
mkdir g3 && echo 495 > g3/blkio.weight
RUNTIME=10
(echo $BASHPID > g1/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=0k &> /dev/null)&
(echo $BASHPID > g2/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=64k &> /dev/null)&
(echo $BASHPID > g3/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=256k &> /dev/null)&
sleep $((RUNTIME+1))
for i in g1 g2 g3; do
echo ---- $i ----
cat $i/blkio.time
done
EOF
# ./cfq-merge-repro.sh
---- g1 ----
8:16 162
---- g2 ----
8:16 165
---- g3 ----
8:16 686
After applying the patch:
# ./cfq-merge-repro.sh
---- g1 ----
8:16 90
---- g2 ----
8:16 445
---- g3 ----
8:16 471
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Provides the ability to identify DAX enabled devices in userspace.
Signed-off-by: Yigal Korman <yigal@plexistor.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
They are unused and potential new users really should use the
blk_rq_map* versions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
I wish the OSD code could simply use blk_rq_map_* helpers like
everyone else, but the complex nature of deciding if we have
DATA IN and/or DATA OUT buffers might make this impossible
(at least for a mere human like me).
But using blk_rq_append_bio at least allows sharing the setup code
between request with or without dat a buffers, and given that this
is the last user of blk_make_request it allows getting rid of that
somewhat awkward interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The target SCSI passthrough backend is much better served with the low-level
blk_rq_append_bio construct then the helpers built on top of it, so export it.
Also use the opportunity to remove the pointless request_queue argument and
make the code flow a little more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_get_request is used for BLOCK_PC and similar passthrough requests.
Currently we always need to call blk_rq_set_block_pc or an open coded
version of it to allow appending bios using the request mapping helpers
later on, which is a somewhat awkward API. Instead move the
initialization part of blk_rq_set_block_pc into blk_get_request, so that
we always have a safe to use request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of a flag and an index just make sure an index of 0 means
no need to free the bvec array. Also move the constants related
to the bvec pools together and use a consistent naming scheme for
them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
WRITE SAME is a data integrity operation and we can't simply ignore
errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently blkdev_issue_zeroout cascades down from discards (if the driver
guarantees that discards zero data), to WRITE SAME and then to a loop
writing zeroes. Unfortunately we ignore run-time EOPNOTSUPP errors in the
block layer blkdev_issue_discard helper to work around DM volumes that
may have mixed discard support underneath.
This patch intoroduces a new BLKDEV_DISCARD_ZERO flag to
blkdev_issue_discard that indicates we are called for zeroing operation.
This allows both to ignore the EOPNOTSUPP hack and actually consolidating
the discard_zeroes_data check into the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For 4K LBA or very large disks, atari_partition can easily get tricked
into thinking it has found an Atari partition table. Depending on the
data in the disk, it ends up creating partitions with awkward lengths.
We saw logs like this while playing with fio.
[5.625867] nvme2n1: AHDI p2
[5.625872] nvme2n1: p2 size 2910030523 extends beyond EOD, truncated
People has had issues with misinterpreted AHDI partition tables for a long
time, see this BSD thread from 1995, for example.
https://mail-index.netbsd.org/port-atari/1995/11/19/0001.html
Since the atari partition, according to the spec, doesn't even support
sector sizes with more than 512, a quick sanity check is reasonable to
just bail out early, before even attempting to read sector 0.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Dan writes:
"The removal of ->driverfs_dev in favor of just passing the parent
device in as a parameter to add_disk(). See below, it has received a
"Reviewed-by" from Christoph, Bart, and Johannes.
It is also a pre-requisite for Fam Zheng's work to cleanup gendisk
uevents vs attribute visibility [1]. We would extend device_add_disk()
to take an attribute_group list.
This is based off a branch of block.git/for-4.8/drivers and has
received a positive build success notification from the kbuild robot
across several configs.
[1]: "gendisk: Generate uevent after attribute available"
http://marc.info/?l=linux-virtualization&m=146725201522201&w=2"
The new nvme-rdma driver will need to reinitialize all the tags as part of
the error recovery procedure (realloc the tag memory region). Add a helper
in blk-mq for it that can iterate over all requests in a tagset to make
this easier.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Stephen Bates <Stephen.Bates@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The new NVMe over fabrics target will make use of this outside from a
module.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For some protocols like NVMe over Fabrics we need to be able to send
initialization commands to a specific queue.
Based on an earlier patch from Christoph Hellwig <hch@lst.de>.
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
[hch: disallow sleeping allocation, req_op fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 9a7f38c42c (cfq-iosched: Convert from jiffies to nanoseconds)
could result in charging just 1 ns to a cgroup submitting IO instead of 1
jiffie we always charged before. It is arguable what is the right amount
to change but for now lets retain the old behavior of always charging at
least one jiffie.
Fixes: 9a7f38c42c
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 9a7f38c42c (cfq-iosched: Convert from jiffies to nanoseconds)
broke the condition for detecting starved sync IO in
cfq_completed_request() because rq->start_time remained in jiffies but
we compared it with nanosecond values. This manifested as a regression
in bonnie++ rewrite performance because we always ended up considering
sync IO starved and thus never increased async IO queue depth.
Since rq->start_time is used in a lot of places, converting it to ns
values would be non-trivial. So just revert the condition in CFQ to use
comparison with jiffies. This will lead to suboptimal results if
cfq_fifo_expire[1] will ever come close to 1 jiffie but so far we are
relatively far from that with the storage used with CFQ (the default
value is 128 ms).
Fixes: 9a7f38c42c
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
slice_resid can be both positive and negative. Commit 9a7f38c42c
(cfq-iosched: Convert from jiffies to nanoseconds) converted it from
long to u64. Although this did not introduce any functional regression
(the operations just overflow and the result was fine), it is certainly
wrong and could cause issues in future. So convert the type to more
appropriate s64.
Fixes: 9a7f38c42c
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently rq->fifo_time is unsigned long but CFQ stores nanosecond
timestamp in it which would overflow on 32-bit archs. Convert it to u64
to avoid the overflow. Since the rq->fifo_time is unioned with struct
call_single_data(), this does not change the size of struct request in
any way.
We have to slightly fixup block/deadline-iosched.c so that comparison
happens in the right types.
Fixes: 9a7f38c42c
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that all drivers that specify a ->driverfs_dev have been converted
to device_add_disk(), the pointer can be removed from struct gendisk.
Cc: Jens Axboe <axboe@fb.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for removing the ->driverfs_dev member of a gendisk, add
an api that takes the parent device as a parameter to add_disk(). For
now this maintains the status quo of WARN()ing on failure, but not
return a error code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch avoids that building with W=1 C=2 triggers the following
warning:
block/bio-integrity.c:35:6: warning: symbol 'blk_flush_integrity' was not declared. Should it be static?
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A value is assigned to the variable 'info' but that value is never
used. Hence remove the variable 'info'.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If ->queue_rq() returns BLK_MQ_RQ_QUEUE_OK, we use continue and skip
over the rest of the loop body. However, dptr is assigned later in the
loop body, and the BLK_MQ_RQ_QUEUE_OK case is exactly the case that we'd
want it for.
NVMe isn't actually using BLK_MQ_F_DEFER_ISSUE yet, nor is any other
in-tree driver, but if the code's going to be there, it might as well
work.
Fixes: 74c450521d ("blk-mq: add a 'list' parameter to ->queue_rq()")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Expose interfaces to tune time slices of CFQ IO scheduler in
microseconds.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Convert all time-keeping in CFQ IO scheduler from jiffies to nanoseconds
so that we can later make the intervals more fine-grained than jiffies.
One jiffie is several miliseconds and even for today's rotating disks
that is a noticeable amount of time and thus we leave disk unnecessarily
idle.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't need bi_rw to be so large on 64 bit archs, so
reduce it to unsigned int.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the is_sync helpers to use separate variables
for the operation and flags.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the block layer merging code to use separate variables
for the operation and flags, and to check req_op for the REQ_OP.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The bio and request operation and flags are going to be separate
definitions, so we cannot pass them in as a bitmap. This patch
converts the blkg_rwstat code and its caller, cfq, to pass in the
values separately.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the elevator code to use separate variables
for the operation and flags, and to check req_op for the REQ_OP.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch modifies the blk mq request creation code to use
separate variables for the operation and flags, because in the
the next patches the struct request users will be converted like
was done for bios.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch prepares *_get_request/*_put_request and freed_request,
to use separate variables for the operation and flags. In the
next patches the struct request users will be converted like
was done for bios where the op and flags are set separately.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The bio users should now always be setting up the bio op. This patch
has the block layer copy that to the request.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This converts the block issue discard helper and users to use
the bio_set_op_attrs accessor and only pass in the operation flags
like REQ_SEQURE.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
submit_bio_wait() gives the caller an opportunity to examine
struct bio and so expects the caller to issue the put_bio()
This fixes a memory leak reported by a few people in 4.7-rc2
kmemleak report after 9082e87bfb ("block: remove struct bio_batch")
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Larry Finger@lwfinger.net
Tested-by: David Drysdale <drysdale@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 0809e3ac62 ("block: fix plug list flushing for nomerge queues")
updated blk_mq_make_request() to set request_count even when
blk_queue_nomerges() returns true. However, blk_mq_make_request() only
does limited plugging and doesn't use request_count;
blk_sq_make_request() is the one that should have been fixed. Do that
and get rid of the unnecessary work in the mq version.
Fixes: 0809e3ac62 ("block: fix plug list flushing for nomerge queues")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
"A set of fixes that wasn't included in the first merge window pull
request. This pull request contains:
- A set of NVMe fixes from Keith, and one from Nic for the integrity
side of it.
- Fix from Ming, clearing ->mq_ops if we don't successfully setup a
queue for multiqueue.
- A set of stability fixes for bcache from Jiri, and also marking
bcache as orphaned as it's no longer actively maintained (in
mainline, at least)"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: clear q->mq_ops if init fail
MAINTAINERS: mark bcache as orphan
bcache: bch_gc_thread() is not freezable
bcache: bch_allocator_thread() is not freezable
bcache: bch_writeback_thread() is not freezable
nvme/host: Add missing blk_integrity tag_size + flags assignments
NVMe: Add device ID's with stripe quirk
NVMe: Short-cut removal on surprise hot-unplug
NVMe: Allow user initiated rescan
NVMe: Reduce driver log spamming
NVMe: Unbind driver on failure
NVMe: Delete only created queues
NVMe: Allocate queues only for online cpus
- Until now, dax has been disabled if media errors were found on
any device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition
is page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent reads/writes
would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX related to
zeroing, writeback, and some size checks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6Of
-----END PGP SIGNATURE-----
Merge tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
blk_mq_init_queue() calls blk_mq_init_allocated_queue(), but q->mq_ops
was not cleared when blk_mq_init_allocated_queue() fails.
Then blk_cleanup_queue() calls blk_mq_free_queue() which will crash because:
- q->all_q_node is not added to all_q_list yet
- q->tag_set is NULL
- hctx was not setup yet or already freed
Fixed it by clearing q->mq_ops on error path.
Signed-off-by: Ming Lin <ming.l@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
1/ Device DAX for persistent memory:
Device DAX is the device-centric analogue of Filesystem DAX
(CONFIG_FS_DAX). It allows memory ranges to be allocated and mapped
without need of an intervening file system. Device DAX is strict,
precise and predictable. Specifically this interface:
a) Guarantees fault granularity with respect to a given page size
(pte, pmd, or pud) set at configuration time.
b) Enforces deterministic behavior by being strict about what fault
scenarios are supported.
Persistent memory is the first target, but the mechanism is also
targeted for exclusive allocations of performance/feature differentiated
memory ranges.
2/ Support for the HPE DSM (device specific method) command formats.
This enables management of these first generation devices until a
unified DSM specification materializes.
3/ Further ACPI 6.1 compliance with support for the common dimm
identifier format.
4/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXQhdeAAoJEB7SkWpmfYgCYP8P/RAgHkroL5lUKKU45TQUBKcY
diC9POeNSccme4tIRIQCGQUZ7+7mKM5ECv2ulF4xYOHvFBCcd/8OF6xKAXs48r3v
oguYhvX1YvIkBc9FUfBQbR1IsCOJ7uWp/UYiYCIQEXS5tS9Jv545j3ASqDt9xWoV
TWlceZn3yWSbASiV9qZ2eXhEkk75pg4yara++rsm2/7rs/TTXn5EIjBs+57BtAo+
6utI4fTy0CQvBYwVzam3m7y9dt2Z2jWXL4hgmT7pkvJ7HDoctVly0P9+bknJPUAo
g+NugKgTGeiqH5GYp5CTZ9KvL91sDF4q00pfinITVdFl0E3VE293cIHlAzSQBm5/
w58xxaRV958ZvpH7EaBmYQG82QDi/eFNqeHqVGn0xAM6MlaqO7avUMQp2lRPYMCJ
u1z/NloR5yo+sffHxsn5Luiq9KqOf6zk33PuxEkKbN74OayCSPn/SeVCO7rQR0B6
yPMJTTcTiCLnId1kOWAPaEmuK2U3BW/+ogg7hKgeCQSysuy5n6Ok5a2vEx/gJRAm
v9yF68RmIWumpHr+QB0TmB8mVbD5SY+xWTm3CqJb9MipuFIOF7AVsPyTgucBvE7s
v+i5F6MDO6tcVfiDT4AiZEt6D2TM5RbtckkUEX3ZTD6j7CGuR5D8bH0HNRrghrYk
KT1lAk6tjWBOGAHc5Ji7
=Y3Xv
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this update was stabilized before the merge window and
appeared in -next. The "device dax" implementation was revised this
week in response to review feedback, and to address failures detected
by the recently expanded ndctl unit test suite.
Not included in this pull request are two dax topic branches (dax
error handling, and dax radix-tree locking). These topics were
deferred to get a few more days of -next integration testing, and to
coordinate a branch baseline with Ted and the ext4 tree. Vishal and
Ross will send the error handling and locking topics respectively in
the next few days.
This branch has received a positive build result from the kbuild robot
across 226 configs.
Summary:
- Device DAX for persistent memory: Device DAX is the device-centric
analogue of Filesystem DAX (CONFIG_FS_DAX). It allows memory
ranges to be allocated and mapped without need of an intervening
file system. Device DAX is strict, precise and predictable.
Specifically this interface:
a) Guarantees fault granularity with respect to a given page size
(pte, pmd, or pud) set at configuration time.
b) Enforces deterministic behavior by being strict about what
fault scenarios are supported.
Persistent memory is the first target, but the mechanism is also
targeted for exclusive allocations of performance/feature
differentiated memory ranges.
- Support for the HPE DSM (device specific method) command formats.
This enables management of these first generation devices until a
unified DSM specification materializes.
- Further ACPI 6.1 compliance with support for the common dimm
identifier format.
- Various fixes and cleanups across the subsystem"
* tag 'libnvdimm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (40 commits)
libnvdimm, dax: fix deletion
libnvdimm, dax: fix alignment validation
libnvdimm, dax: autodetect support
libnvdimm: release ida resources
Revert "block: enable dax for raw block devices"
/dev/dax, core: file operations and dax-mmap
/dev/dax, pmem: direct access to persistent memory
libnvdimm: stop requiring a driver ->remove() method
libnvdimm, dax: record the specified alignment of a dax-device instance
libnvdimm, dax: reserve space to store labels for device-dax
libnvdimm, dax: introduce device-dax infrastructure
nfit: add sysfs dimm 'family' and 'dsm_mask' attributes
tools/testing/nvdimm: ND_CMD_CALL support
nfit: disable vendor specific commands
nfit: export subsystem ids as attributes
nfit: fix format interface code byte order per ACPI6.1
nfit, libnvdimm: limited/whitelisted dimm command marshaling mechanism
nfit, libnvdimm: clarify "commands" vs "_DSMs"
libnvdimm: increase max envelope size for ioctl
acpi/nfit: Add sysfs "id" for NVDIMM ID
...
Al Viro