In clk_bulk_get(), if we fail to get the clock due to probe deferal, we
shouldn't print an error message. Just be silent in this case.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are two USB3 host controllers on Hi3798CV200 SoC.
This commit adds missing clocks for them.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This commit fixes incorrect setting of reset bits for PCI/VGA and
PECI modules.
1. Reset bit for PCI/VGA is 8.
2. PECI reset bit is missing so added bit 10 as its reset bit.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ast2500 has an additional reset register that contains resets not
present in the ast2400. This enables support for this register, and adds
the one reset line that is controlled by it.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Stratix10 clock driver is essential to system operation, so their
removal should never happen.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use platform driver APIs to map memory so that it will automatically free
the memory in case of errors.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
[sboyd@kernel.org: Return -ENOMEM error pointers, check for error
pointer at call site]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock for MPEG2 transport stream I/O and demux system (HSC) on
UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We allocate some memory which is neither used, nor referenced by anything.
So axe it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Don't disable the dbg clock if was set by bootloader.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk81 is not expected to be changed, so drop this flag.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Adds a Clock and Reset controller driver for the Always-On part
of the Amlogic Meson-AXG SoC.
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
We try to refactor the common code into one dedicated file,
while preparing to add new Meson-AXG aoclk driver, this would
help us to better share the code by all aoclk drivers.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
There is a protential memory leak, as of_clk_del_provider is
never called if of_clk_add_hw_provider has been executed.
Fix this by using devm variant API.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the SEL/DIV/GATE for VDEC_1 and VDEC_HEVC.
Signed-off-by: Maxime Jourdan <maxi.jourdan@wanadoo.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the NAND clocks (from the HHI_NAND_CLK_CNTL register) to the
Meson8b clock driver. There are three NAND clocks: a gate which enables
or disables the NAND clock, a mux and a divider (which divides the mux
output).
Unfortunately the public S805 datasheet does not document the mux
parents. However, the vendor kernel has a few hints for us which allows
us to make an educated guess about the clock parents. To do this we need
to have a look at set_nand_core_clk() from the vendor's NAND driver (see
[0]):
- XTAL = (4<<9) | (1<<8) | 0
- 160MHz = (0<<9) | (1<<8) | 3)
- 182MHz = (3<<9) | (1<<8) | 1)
- 212MHz = (1<<9) | (1<<8) | 3)
- 255MHz = (2<<9) | (1<<8) | 1)
While there is a comment for the XTAL parent (which indicates that it
should only be used for debugging) we have to do a bit of math for the
other parents: target_freq * divider = rate of parent clock
Bit 8 above is the enable bit, so we can ignore it here. Bits 11:9 are
the mux index and bits 6:0 are the 0-based divider (so we need to add
1). This gives us:
- mux 0 (160MHz * 4) = fclk_div4 (actual rate = 637.5MHz, off by 2.5MHz)
- mux 1 (212MHz * 4) = fclk_div3 (actual rate = 850MHz, off by 2MHz)
- mux 2 (255MHz * 2) = fclk_div5 (matches exactly 510MHz)
- mux 3 (182MHz * 2) = fclk_div7 (actual rate = 346.3MHz, off by 0.3MHz)
[0] https://github.com/khadas/linux/blob/9587681285cb/drivers/amlogic/amlnf/dev/amlnf_ctrl.c#L314
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
_freq_tbl_determine_rate uses the pre_div found in the clock plan
multiplied by the requested rate from the caller to determine the
best parent rate to set. If the requested rate is not exactly equal
to the rate that was found in the clock plan, then using the requested
rate in parent rate calculations is incorrect. For instance, if 150MHz
was requested, but 200MHz was the match found, and that plan had a
pre_div of 3, then the parent should be set to 600MHz, not 450MHz.
Signed-off-by: Evan Green <evgreen@chromium.org>
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Initial support for R-Car E3 (r8a77990), including core and module
clocks.
Based on the Table 8.2g of "R-Car Series, 3rd Generation User's Manual:
Hardware ((Rev. 0.80, Oct 31, 2017) with Manual Errata on Feb. 28, 2018".
Inspried by patches by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the global clock controller found on SDM845
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There could be few clocks where the clock status bit is not
required to be polled as the clock on/off would be controlled
by enabling/disabling external source. Add support for the
same by introducing new flag named as 'BRANCH_HALT_SKIP'.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd@kernel.org: Rename flag to BRANCH_HALT_SKIP]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The code is complicated because we want to check if the GDSC is enabled
or disabled based on different bits in different registers while the
GDSC hardware is slightly different across chips. Furthermore, we poll
the status of the enable or disable state by checking if the gdsc is
enabled or not, and then comparing that to if the gdsc is being enabled
or disabled. Let's push all that into one function, so we can ask if the
status matches what we want, either on or off. Then the call site can
just ask that question, and the logic to check that state can simply
return yes or no, and not 1 or 0 or 0 or 1 depending on if we're
enabling or disabling respectively.
Tested-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some root clock generators, there could be child branches which are
controlled by an entity other than application processor subsystem. For
such RCGs, as per application processor subsystem clock driver, all of
its downstream clocks are disabled and RCG is in disabled state but in
reality downstream clocks can be left enabled before.
So in this scenario, when RCG is disabled as per clock driver's point of
view and when rate scaling request comes before downstream clock enable
request, then RCG fails to update its configuration because in reality
RCG is on and it expects its new source to already be in enable state but
in reality new source is off. In order to avoid having the RCG to go into
an invalid state, add support to update the CFG, M, N and D registers
during set_rate() without configuration update and defer the actual RCG
configuration update to be done during clk_enable() as at this point of
time, both its new parent and safe source will be already enabled and RCG
can safely switch to new parent.
During clk_disable() request, configure it to safe source as both its
parents, safe source and current parent will be enabled and RCG can
safely execute a switch.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has lvds2 (analog clock2), an I/O clock like lvds1.
And this lvds2, along with lvds1, can be used to provide
external clock source to the internal pll, such as pll4_audio
and pll5_video.
This patch mainly adds the lvds2 to the clock tree and fix its
relationship with pll accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the data sheet the 3rd choice is the bypass clock
of pll2. This should not have any effect in practice as this
selection is not used currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The H6 has clock/reset controls in PRCM part, like old SoCs such as H3
and A64. However, the PRCM CCU is rearranged; the register arragement
is now similar to the main CCU of H6, and the PRCM now has two APB
buses to control -- one is clocked from AHB clock derivde from AR100
clock, the other is clocked from the same mux with AR100 clock.
Therefore a new driver is written for it.
As there's no official document about the PRCM in H6, all the information
are indirectly collected from BSP and parts of the document, and the
information source is noted as comments in the driver's source code. If
reliable information is provided furtherly, the driver needs to be
rechecked.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The default behavior of the GDSC enable/disable sequence is to
poll the status bits of either the actual GDSCR or the
corresponding HW_CTRL registers.
On targets which have support for a CFG_GDSCR register, the
status bits might not show the correct state of the GDSC,
especially in the disable sequence, where the status bit
will be cleared even before the core is completely power
collapsed. On targets with this issue, poll the power on/off
bits in the CFG_GDSCR register instead to correctly determine
the GDSC state.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In case of error, the function ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: fcfd143698 ("clk: npcm7xx: add clock controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
meson8b_cpu_clk has two parent clocks:
- meson8b_xtal
- meson8b_cpu_scale_out_sel
The name of the "xtal" clock parent is specified correctly. However,
there is a typo in the name of the second parent clock. The
meson8b_cpu_scale_out_sel definition uses the name "cpu_scale_out_sel"
(which matches the name from the datasheet). However, the mux parent
definition uses the name "cpu_out_sel" which does not match any existing
clock.
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The names of all fclk divider gate clocks follow the naming schema
"fclk_divN" and the name of all fclk fixed dividers follow the naming
schema "fclk_divN_div".
There's one exception to this rule: meson8b_fclk_div3_div's name is
"fclk_div_div3". It's child clock meson8b_fclk_div3 however references
it as "fclk_div3_div" (following the naming schema explained above).
Fix the naming of the meson8b_fclk_div3_div clock to follow the naming
schema. This also fixes serial console on my Meson8m2 board because
"clk81" uses fclk_div3 as parent. However, since the hierarchy stops at
meson8b_fclk_div3 there's no known parent clock and the rate of "clk81"
and all of it's children (UART clock, SDIO MMC controller clock, ...)
are all 0.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Since commit c08ee14cc6 ("clk: ti: change clock init to use
generic of_clk_init"), there is only a single (private) user left of the
(public) clk_init_cb typedef.
Hence expand its single user in the core clock code, and remove the
typedef.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1523365565-17124-1-git-send-email-geert+renesas@glider.be
Add support for the global clock controller found on MSM8998
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Specify regs for alpha_plls, fix white spaces and add binding]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some gdscs, it might take longer time up to 500us for updating their
status. Update the timeout value for all GDSC polling status.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some of the gdsc power domains, there could be need to reset the
AON logic or assert/deassert the block control reset before removing
the clamp_io. Add support for the same by introducing new flags
SW_RESET and AON_RESET. Both SW reset and AON reset requires to be
asserted for at least 1us before being de-asserted.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Nuvoton Poleg BMC NPCM7XX contains an integrated clock controller, which
generates and supplies clocks to all modules within the BMC.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
[sboyd@kernel.org: Drop clk_get()s, cleanup whitespace, drop unused
includes, fix static checker warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Using __clk_mux_determine_rate effectively ignores CLK_MUX_ROUND_CLOSEST
if set the related clk_regmap mux instance.
Use clk_mux_determine_rate_flags() to make sure the flag is honored.
Fixes: ea11dda9e0 ("clk: meson: add regmap clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CLK_MUX_ROUND_CLOSEST is part of the clk_mux documentation but clk_mux
directly calls __clk_mux_determine_rate(), which overrides the flag.
As result, if clk_mux is instantiated with CLK_MUX_ROUND_CLOSEST, the
flag will be ignored and the clock rounded down.
To solve this, this patch expose clk_mux_determine_rate_flags() in the
clk-provider API and uses it in the determine_rate() callback of clk_mux.
Fixes: 15a02c1f6d ("clk: Add __clk_mux_determine_rate_closest")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When power management is disabled, we get a harmless warning:
drivers/clk/clk-cs2000-cp.c:544:12: error: 'cs2000_resume' defined but not used [-Werror=unused-function]
Marking the function as __maybe_unused lets the compiler silently
drop it instead.
Fixes: eade4ccdb0 ("clk: cs2000: set pm_ops in hibernate-compatible way")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Introduce centralized quirks handling like on R-Car Gen3, and convert
the RZ/G1C SD clock table handling over to it.
This makes it easier to add more quirks later, if/when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of
December 22, 2017, the parent clock of the PCIe module clock on R-Car
V3H is S2D2.
Fixes: ce15783c51 ("clk: renesas: cpg-mssr: add R8A77980 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The CLK_TYPE_GEN2_LB clock type is meant for SoCs like R-Car H2, where
the LB clock divider depends on the value of the MD18 pin.
On R-Car E2, the LB clock divider is fixed to 24. Hence model the clock
as a fixed factor clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
The CLK_TYPE_GEN2_LB clock type is meant for SoCs like R-Car H2, where
the LB clock divider depends on the value of the MD18 pin.
On R-Car V2H, the LB clock divider is fixed to 24. Hence model the
clock as a fixed factor clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
The CLK_TYPE_GEN2_LB clock type is meant for SoCs like R-Car H2, where
the LB clock divider depends on the value of the MD18 pin.
On R-Car M2-W and M2-N, the LB clock divider is fixed to 24. Hence
model the clock as a fixed factor clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
The CLK_TYPE_GEN2_LB clock type is meant for SoCs like R-Car H2, where
the LB clock divider depends on the value of the MD18 pin.
On RZ/G1E, the LB clock divider is fixed to 24. Hence model the clock
as a fixed factor clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
The CLK_TYPE_GEN2_LB clock type is meant for SoCs like R-Car H2, where
the LB clock divider depends on the value of the MD18 pin.
On RZ/G1M, the LB clock divider is fixed to 24. Hence model the clock
as a fixed factor clock instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Add support for Actions Semi PLL clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi composite clock. This clock
consists of gate, mux, divider, factor and fixed factor clocks.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi fixed factor clock reusing the clk
ops from common clock driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi factor clock together with
helper functions to be used in composite clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi divider clock together with
helper functions to be used in composite clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi mux clock together with helper
functions to be used in composite clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi gate clock together with helper
functions to be used in composite clock.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for Actions Semi common clock driver with generic structures
and interface functions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no SPEAr600 device named "wdt". Instead, the description of the
WDT (watchdog) was recently added to the Device Tree, and the device
name is "fc880000.wdt", so we should associate the WDT fixed rate clock
to this device name.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's recommended to use only clk_sys_dbg clock instead to activate
debug IP.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
stgen_k should be declared as critical to avoid blocking console
when ck_hsi is not used.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds tzc2 clock and rename tzc clock into tzc1
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
fix bad copy / paste.
SAI3 & SAI4 used gate of SAI2 instead SAI3 & SAI4
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing static for const parent names and clock ops.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-davinci:
clk: davinci: add a reset lookup table for psc0
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
In order to be able to use the reset framework in legacy boot mode as
well, add the reset lookup table to the psc driver for da850 variant.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-davinci:
clk: davinci: Remove redundant dev_err calls
clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
clk: davinci: New driver for TI DA8XX CFGCHIP clocks
dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
clk: davinci: Add platform information for TI DM646x PSC
clk: davinci: Add platform information for TI DM644x PSC
clk: davinci: Add platform information for TI DM365 PSC
clk: davinci: Add platform information for TI DM355 PSC
clk: davinci: Add platform information for TI DA850 PSC
clk: davinci: Add platform information for TI DA830 PSC
clk: davinci: New driver for davinci PSC clocks
dt-bindings: clock: New bindings for TI Davinci PSC
clk: davinci: Add platform information for TI DM646x PLL
clk: davinci: Add platform information for TI DM644x PLL
clk: davinci: Add platform information for TI DM365 PLL
clk: davinci: Add platform information for TI DM355 PLL
clk: davinci: Add platform information for TI DA850 PLL
clk: davinci: Add platform information for TI DA830 PLL
clk: davinci: New driver for davinci PLL clocks
dt-bindings: clock: Add new bindings for TI Davinci PLL clocks
* clk-si544:
clk: Add driver for the si544 clock generator chip
* clk-rockchip:
clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
clk: rockchip: Fix error return in phase clock registration
clk: rockchip: Correct the behaviour of restoring cached phase
clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: rockchip: Add 1.6GHz PLL rate for rk3399
clk: rockchip: Restore the clock phase after the rate was changed
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: rockchip: Free the memory on the error path
clk: rockchip: document hdmi_phy external input for rk3328
clk: rockchip: add flags for rk3328 dclk_lcdc
clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
clk: rockchip: protect all remaining rk3328 interconnect clocks
clk: rockchip: export sclk_hdmi_sfc on rk3328
clk: rockchip: remove HCLK_VIO from rk3328 dt header
clk: rockchip: fix hclk_vio_niu on rk3328
* clk-uniphier:
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: uniphier: add ethernet clock control support for PXs3
clk: uniphier: add Pro4/Pro5/PXs2 audio system clock
* clk-ti-flag-fix:
clk: ti: fix flag space conflict with clkctrl clocks
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
* clk-mvebu:
clk: mvebu: armada-38x: add support for missing clocks
clk: mvebu: cp110: Fix clock tree representation
* clk-phase:
clk: Don't show the incorrect clock phase
clk: update cached phase to respect the fact when setting phase
* clk-nxp:
clk: lpc32xx: Set name of regmap_config
* clk-mtk2712:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clocks for MT2712
* clk-qcom-rpmcc:
clk: qcom: rpmcc: Add support to XO buffered clocks
Add clk driver support for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new gate/gate2 wrapper function to register clocks with optional flags.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The busy divider and busy mux is actually used by the system critical clocks,
so add 'CLK_IS_CRITICAL' to clocks registered with these two type.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use SET_LATE_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.resume_early field.
This fixes initialization of CS2000 in restore from hibernation in case
of kernel used to load image did not initialize CS2000 while kernel
being restored had CS2000 initialized.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For init on clocks we should move it at the first place in imx7d_clocks_init()
before any clock operations, else the clock operation may fail in case the clock
is still not on.
Acked-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Design team change the ahb's clk parent options but
did NOT update the DOC accordingly in time, so the
AHB/IPG's clk rate in clk tree is incorrect, AHB is
67.5MHz and IPG is 33.75MHz, but using scope to
monitor them, they are actually 135MHz and 67.5MHz,
update the clk parent option to make clk tree info
correct.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.
There is a test_div placed before DRAM PLL's gate, so
add this test div clk.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add USB clock information, the pll_usb_main_clk is USB_PLL at CCM
which is the output of USBOTG2 PHY.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock driver for the Stratix10 SoC. The driver is similar to the
Cyclone5/Arria10 platforms, with the exception that this driver only uses
one single clock binding.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes and
the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we get
two new machines based on its older siblings: the H5 based OrangePi
Zero+ and the A64 based Teres-I Laptop from Olimex. On the 32-bit side,
we add The Olimex som204 based on Allwinner A20, and the Banana Pi M2
Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6
family of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones Qualcomm
msm8974 based Galaxy S5 is a rather different phone made by the same
company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre Computer
Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on Rockchips
RK3368 and made by Theobroma Systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7rHo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
The introduction of support for CLK_SET_RATE_PARENT flag for clkctrl
clocks used a generic clock flag, which causes a conflict with the
rest of the clkctrl flags, namely the NO_IDLEST flag. This can cause
boot failures on certain platforms where this flag is introduced, by
omitting the wait for the clockctrl module to be fully enabled before
proceeding with rest of the code.
Fix this by moving all the clkctrl specific flags to their own bit-range.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes: 49159a9dc3 ("clk: ti: add support for CLK_SET_RATE_PARENT flag")
Reported-by: Christophe Lyon <christophe.lyon@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pro4 SoC has clock lines for Giga-bit feature and ethernet phy,
and these are mandatory to activate the ethernet controller. This adds
support for the clock lines.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock control for SATA controller on UniPhier SoCs. This adds
support for PXs2, LD20 and PXs3.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock control for PCIe controller on UniPhier SoCs. This adds
support for Pro5, LD20 and PXs3.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI544 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 200kHz
to 1500MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd: assign max_freq to 0 in is_valid_frequency() to squelch warning]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since hclk_sd and pclk_ddr source clock from CPLL or GPLL,
and these two PLL may change their frequency. If we do not
assign right id to pclk_ddr and hclk_sd, they will alway use
default cur register value, and may get the frequency
exceed their signed off frequency. So assign correct Id
for them, then we can assign frequency for them in dts.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The newly added clock notifier may return an error code but so far the
error output in the function would only return an error pointer from
registering the clock.
So when the clock notifier fails the clock would be unregistered but the
return would still be the clock pointer which could then not be
dereferenced correctly. So fix the error handling to prevent that.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We can't restore every phase, for instance the invalid phase and
the phase for coming rate which is out of the scope of boards'
ability. And this patch also corrects the error path to return
invalid pointer to clk if clk_notifier_register failed introduced
by the same offending commit.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Reported-by: wlq <wlq@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: wlq <wlq@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase if
clock rate is zero") catches some gremlins for clk-rk3328.c that the
parents of MMC phase clock should be clk_{sdmmc, sdio, emmc}, but not
sclk_{sdmmc, sdio, emmc}.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adjust the R8A77980-specific #ifdefs to use CLK instead of ARCH
to follow same style as other SoCs.
Fixes: ce15783c51 ("clk: renesas: cpg-mssr: add R8A77980 support")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 CPG/MSSR driver (again) uses a mix of
clk_readl()/clk_writel() and readl()/writel() to access the clock
registers. Settle on the generic readl()/writel().
Cfr. commit 30ad3cf00e ("clk: renesas: rcar-gen3-cpg: Always use
readl()/writel()").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32/arm64, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Allwinner H6 CCU has a "HDMI Slow Clock", which is currently missing
in the ccu-sun50i-h6 driver.
Add this missing clock to the driver.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Fixes: 322269163a ("clk: hisilicon: add hisi_clk_alloc function.")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for the USB PHY clocks in the CFGCHIP2 syscon
register on TI DA8XX-type SoCs.
The USB0 (USB 2.0) PHY clock is an interesting case because it calls
clk_enable() in a reentrant way. The USB 2.0 PSC only has to be enabled
temporarily while we are locking the PLL, which takes place during the
clk_enable() callback.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for the gate and multiplexer clocks in the
CFGCHIPn syscon registers on TI DA8XX-type SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM646x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM644x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM365 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM355 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI DA850/
OMAP-L138/AM18XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI DA830/
OMAP-L137/AM17XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for mach-davinci PSC clocks. This is porting the
code from arch/arm/mach-davinci/psc.c to the common clock framework and
is converting it to use regmap to simplify the code. Additionally, it
adds device tree support for these clocks.
Note: although there are similar clocks for TI Keystone we are not able
to share the code for a few reasons. The keystone clocks are device tree
only and use legacy one-node-per-clock bindings. Also the keystone
driver makes the assumption that there is only one PSC per SoC and uses
global variables, but here we have two controllers per SoC.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM646x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM644x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM365 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM355 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI DA850/
OMAP-L138/AM18XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI DA830/
OMAP-L137/AM17XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for mach-davinci PLL clocks. This is porting the
code from arch/arm/mach-davinci/clock.c to the common clock framework.
Additionally, it adds device tree support for these clocks.
The ifeq ($(CONFIG_COMMON_CLK), y) in the Makefile is needed to prevent
compile errors until the clock code in arch/arm/mach-davinci is removed.
Note: although there are similar clocks for TI Keystone we are not able
to share the code for a few reasons. The keystone clocks are device tree
only and use legacy one-node-per-clock bindings. Also the register
layouts are a bit different, which would add even more if/else mess
to the keystone clocks. And the keystone PLL driver doesn't support
setting clock rates.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit aa795c41d9 ("clk: Add devm_of_clk_add_hw_provider()/del_provider()
APIs") adds devm_of_clk_add_hw_provider which takes care of deleting the
clock provider when the clock providers device is removed.
This patch makes use of devm_of_clk_add_hw_provider() instead of
of_clk_add_hw_provider() so that we can eliminate the need of explicit
scmi_clocks_remove for just doing of_clk_del_provider()
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add devm_of_platform_populate() to populate devices which are children
of the root node.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic updating of the output frequency
("frequency slewing") without need to turn off the PLL
before configuration. Add support for initial configuration
and programming sequence to control fabia PLLs.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd: Shorten code a little]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For upcoming targets like sdm845, POR value of the hardware clock control
bit is set for most of root clocks which needs to be cleared for software
to be able to control. For older targets like MSM8996, this bit is reserved
bit and having POR value as 0 so this patch will work for the older targets
too. So update the configuration mask to take care of the same to clear
hardware clock control bit.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
XO is onchip buffer clock to generate 19.2MHz.
This patch adds support to 5 XO buffer clocks found on PMIC8921,
these buffer clocks can be controlled from external pin or in
manual mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to ECO design change,
1. add new clock mux data and change some
2. add new clock gate data and clock factor data
3. change status register offset of infra subsystem
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's found that the clock phase output from clk_summary is
wrong compared to the actual phase reading from the register.
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 -22
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).
They have also some dip-switches to select a different clock (666, 800,
1066, 1200).
The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).
This patch add all the missing clocks.
The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).
Fixes: 0e85aeced4 ("clk: mvebu: add clock support for Armada 380/385")
Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56cf5: clk: mvebu: armada-38x: add support for 1866MHz variants
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When changing or retrieving clock parents, the caller is in a sleepable
state (like prepare) so the GPIO operation need not be atomic. Replace
gpiod_{g|s}et_value with gpiod_{g|s}et_value_cansleep in the {g|s}et_parent
calls for the GPIO based clock mux.
This fixes a "slowpath" warning when the GPIO controller is an I2C expander
or something similar.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Without COMMON_CLK_HI655X Wifi and bluetooth are non-functional on Hikey.
As suggested by Arnd, enable the driver automatically when the parent
driver is selected. With sensible defaults in place, we can leave other
choices for EXPERT.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add two configuration flags to be able to not compile all the time
stm32f and stm32h7 drivers when ARCH_STM32 is set.
That help to save some space on those small platforms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
STM32F769 has 2 SDMMC port, add clock entry for the second one.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds DSI clock for STM32F469 board
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing clock data 'CLK_AUDIO_AFE_CONN' for MT7622 audsys.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock for which all PWM devices on MT7623 or MT2701 actually depending
on has to be divided by four from its parent clock axi_sel in the clock
path prior to PWM devices.
Consequently, adding a fixed-factor clock axisel_d4 as one-fourth of
clock axi_sel allows that PWM devices can have the correct resolution
calculation.
Cc: stable@vger.kernel.org
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Thanks to new documentation, we have a better view of the clock tree.
There were few mistakes in the first version of this driver, the main one
being the parental link between the clocks. Actually the tree is more
flat that we though. Most of the IP blocks require two clocks: one for
the IP itself and one for accessing the registers, and unlike what we
wrote there is no link between these two clocks.
The other mistakes were about the name of the clocks: the root clock is
not the Audio PLL but the PLL0, and what we called the EIP clock is named
the x2 Core clock and is used by other IP block than the EIP ones.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CM_PLLx and A2W_XOSC_CTRL registers are accessed by different clock
handlers and must be accessed with ->regs_lock held.
Update the sections where this protection is missing.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ana->maskX values are already '~'-ed in bcm2835_pll_set_rate(). Remove
the '~' in the definition to fix ANA setup.
Note that this commit fixes a long standing bug preventing one from
using an HDMI display if it's plugged after the FW has booted Linux.
This is because PLLH is used by the HDMI encoder to generate the pixel
clock.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Allwinner H6 SoC has a CCU which has been largely rearranged.
Add support for it in the sunxi-ng CCU framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the new Allwinner H6 SoC, multiple PLL's are NMP style clocks
(modelled as NKMP with no K) and have fixed post-dividers.
Add fixed post divider support to the NKMP style clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When getting the clock related warnings, it is useful to know what
is the clock name that is causing the problem and the cause of the
problem.
Add the clock name and the the warning cause to the log, so that the
output becomes clearer like this:
[ 2.383969] ------------[ cut here ]------------
[ 2.388720] WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:814 clk_core_disable+0xd4/0xf8
[ 2.396658] uart4_ipg_gate already disabled
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The symbol is in the __initconst section but not marked init, which
caused a warning when building with LTO.
This makes it 'const' as was obviously intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c80dfd9bf5 ("clk: hisilicon: add CRG driver for Hi3516CV300 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When we build this driver with on x86-32, gcc produces a false-positive warning:
drivers/clk/renesas/clk-sh73a0.c: In function 'sh73a0_cpg_clocks_init':
drivers/clk/renesas/clk-sh73a0.c:155:10: error: 'parent_name' may be used uninitialized in this function [-Werror=maybe-uninitialized]
return clk_register_fixed_factor(NULL, name, parent_name, 0,
We can work around that warning by adding a fake initialization, I tried
and failed to come up with any better workaround. This is currently one
of few remaining warnings for a 4.14.y randconfig build, so it would be
good to also have it backported at least to that version. Older versions
have more randconfig warnings, so we might not care.
I had not noticed this earlier, because one patch in my randconfig test
tree removes the '-ffreestanding' option on x86-32, and that avoids
the warning. The -ffreestanding flag was originally global but moved
into arch/i386 by Andi Kleen in commit 6edfba1b33 ("[PATCH] x86_64:
Don't define string functions to builtin") as a 'temporary workaround'.
Like many temporary hacks, this turned out to be rather long-lived, from
all I can tell we still need a simple fix to asm/string_32.h before it
can be removed, but I'm not sure about how to best do that.
Cc: stable@vger.kernel.org
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a few gate clocks which are used for gating RTC for some
devices on AON area of SC9860.
This patch has been tested on SC9860, with this patch and proper DT
configurations, the watchdog can be initialized and work well.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Forward the errors returned by __clk_pllv2_set_rate() in the recalc rate
function, to avoid using uninitialized values for the rate calculation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
aggre0 bus clks are not associated with any of the drivers, so its
important that these clks are always on to get peripherals on this
bus working. So mark them as critical.
Eventually when we have a proper bus driver these clks can be marked
appropriately.
Without this patch pcie on db820c is not functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_round_rate() is intended to be used to round a given clock rate to
the closest one achievable by the actual clock. This implies that the
input to clk_round_rate() is expected to be unachievable - and such
cases shouldn't be treated as exceptional.
To reflect this, remove the WARN_ONs which trigger when an unachievable
clock rate is passed to vexpress_osc_round_rate().
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework has a provider API(clk_hw_set_rate_range) to set the
min/max rate of a clock. Use the same to set the boundaries for the
vexpress osc clock.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Running sparse on the samsung clk directory has some noise that we can
fix to look for future problems easier.
drivers/clk/samsung/clk-s3c2443.c:111:26: warning: symbol 's3c2443_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:139:26: warning: symbol 's3c2443_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:152:27: warning: symbol 's3c2443_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:186:28: warning: symbol 's3c2443_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:241:26: warning: symbol 's3c2416_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:247:26: warning: symbol 's3c2416_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:253:27: warning: symbol 's3c2416_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:263:28: warning: symbol 's3c2416_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:291:26: warning: symbol 's3c2443_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:296:27: warning: symbol 's3c2443_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:305:28: warning: symbol 's3c2443_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:321:26: warning: symbol 's3c2450_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:328:26: warning: symbol 's3c2450_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:334:27: warning: symbol 's3c2450_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:345:28: warning: symbol 's3c2450_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:368:33: warning: symbol 's3c2443_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:464:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:470:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:476:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2412.c:96:26: warning: symbol 's3c2412_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:108:35: warning: symbol 's3c2412_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:128:26: warning: symbol 's3c2412_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:146:27: warning: symbol 's3c2412_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:177:28: warning: symbol 's3c2412_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:227:33: warning: symbol 's3c2412_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:292:43: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:98:26: warning: symbol 's3c2410_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:114:26: warning: symbol 's3c2410_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:119:27: warning: symbol 's3c2410_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:138:28: warning: symbol 's3c2410_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:203:26: warning: symbol 's3c2410_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:207:35: warning: symbol 's3c2410_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:218:28: warning: symbol 's3c2410_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:272:26: warning: symbol 's3c244x_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:277:35: warning: symbol 's3c244x_common_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:294:26: warning: symbol 's3c244x_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:302:27: warning: symbol 's3c244x_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:306:28: warning: symbol 's3c244x_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:321:26: warning: symbol 's3c2440_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:325:27: warning: symbol 's3c2440_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:331:35: warning: symbol 's3c2442_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:337:26: warning: symbol 's3c2442_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:346:33: warning: symbol 's3c2410_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:471:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:477:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:483:49: warning: Using plain integer as NULL pointer
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the Aspeed specification, the reset and enable sequence
should be done when the clock is stopped. The specification doesn't
define behavior if the reset is done while the clock is enabled.
From testing on the AST2500, the LPC Controller has problems if the
clock is reset while enabled.
Therefore, check whether the clock is enabled or not before performing
the reset and enable sequence in the Aspeed clock driver.
Reported-by: Lei Yu <mine260309@gmail.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the Aspeed clocks are disabled by setting the relevant bit in
the "clock stop control" register to one, while others are disabled by
setting their bit to zero. The driver already uses a flag per gate to
identify this behavior, but doesn't apply it in the clock is_enabled
function.
Use the existing gate flag to correctly return whether or not a clock
is enabled in the aspeed_clk_is_enabled function.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 6671507f0f ("clk: aspeed: Handle inverse polarity of USB port 1 clock gate")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following warnings:
drivers/clk/meson/meson8b.c:512:19: warning: symbol 'meson8b_mpeg_clk_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:526:19: warning: symbol 'meson8b_clk81' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:540:19: warning: symbol 'meson8b_cpu_in_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:591:19: warning: symbol 'meson8b_cpu_scale_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:608:19: warning: symbol 'meson8b_cpu_scale_out_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:626:19: warning: symbol 'meson8b_cpu_clk' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:392:27: warning: symbol 'gxbb_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:439:27: warning: symbol 'gxl_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:195:27: warning: symbol 'axg_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:248:27: warning: symbol 'axg_hifi_init_regs' was not declared. Should it be static?
drivers/clk/meson/meson8b.c: In function 'meson8b_clkc_probe':
drivers/clk/meson/meson8b.c:1052:14: warning: unused variable 'clk' [-Wunused-variable]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJapy5hAAoJEFBXWFqHsHzOzuIIAKtLJDt8GVHdR/NHmPVvP2I1
CL0UJVaPdef4hCbV1fKdv0gRdd28rlZsKwJLvOdiRnp826sTGfbKEJF9qX3Uolt9
33RXsly35V16fzu0UhrhbcNFsjrUHeNqG50OUMEGjYtYgM/G0qkSQryl3UENS5tt
KVuYzoR45XdCaoZaLNfSwEgYPvMh/3Qbb0hm7rMVrbmVnXAKAam+2vlTqo2rZymR
Eo+zmomTIPCnbijIguq+HQcIpuhAJNpFvad2hhyiZpk76FkHC2pTtJ4b8MTSNg+1
ogn1TTcUkibkPYt26SqexCWn/7kvuYqzEtsQ2RvoaBBAOiR0zNktWMXBc621aE0=
=KJta
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX clock misc updates from Shawn Guo:
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
* tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6ull: Add epdc_podf instead of sim_podf
clk: imx: imx7d: correct video pll clock tree
clk: imx: imx6sx: update cko mux options
Sparse rightfully complains:
drivers/clk/hisilicon/clk-hisi-phase.c:88:22: warning: symbol 'clk_phase_ops' was not declared. Should it be static?
drivers/clk/hisilicon/clk-hisi-phase.c:88:22: warning: symbol 'clk_phase_ops' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
FIMC LITE SYSMMU devices are defined in exynos5250.dtsi, but clocks for
them are not instantiated by Exynos5250 clock provider driver. Add needed
definitions for those clocks to fix IOMMU probe failure:
ERROR: could not get clock /soc/sysmmu@13c40000:sysmmu(0)
exynos-sysmmu 13c40000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c40000.sysmmu failed with error -38
ERROR: could not get clock /soc/sysmmu@13c50000:sysmmu(0)
exynos-sysmmu 13c50000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c50000.sysmmu failed with error -38
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: bfed1074f2 ("clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks")
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We need this rate to generate 100, 200, and 228.57MHz from the same
PLL. 228.57MHz is useful for a pixel clock when the VPLL is used for
an external display.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
R-Car M3-N does not have the DU2 unit but it has DU3 instead.
Fix the module clock definition to reflect that.
Fixes: 7ce36da900 ("clk: renesas: cpg-mssr: Add support for R-Car M3-N")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are many factors affecting the clock phase, including clock
rate, temperature, logic voltage and silicon process, etc. But clock
rate is the most significant one here, and the driver should be aware
of the change of the clock rate. As mmc controller need a fixed phase
after tuning was completed, at least before explicitly doing re-tune,
so this patch try to restore the clock phase by monitoring the event
of rate change.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the hifi pll to the axg clock controller. This clock maybe used as an
input of the axg audio clock controller. It uses the same settings table
as the gp0 pll but has a frac parameter allowing more precision.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Provide an option for the pll driver to round to the rate closest to the
requested rate, instead of systematically rounding down.
This may allow the provided rate to be closer to the requested rate when
rounding up is not an issue
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the frac parameter for the gp0 pll of the axg and gxl.
This allows to achieve rates between the fixed settings provided
by the table.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finding the appropriate settings of meson plls is too tricky to be done
entirely at runtime, using calculation only. Many combination of m, n
and od won't lock which is why we are using a table for this. However,
for plls having a fractional parameters, it is possible to improve on
the result provided by the table by calculating the frac parameter.
This change adds the calculation of frac when the parameter is available
and the rate provided by the table is not an exact match for the
requested rate.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After testing, it appears that the gxl (and axg) does not require the
special locking/reset loop which was initially added for it.
All the values present in the gxl table can locked with the simple lock
checking loop.
The change switches the gxl and axg gp0 back to the simple lock checking
loop and removes the code no longer required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the missing frac parameter to the meson8b fixed_pll. It seems to be
always on this platform, so the rate remains unchanged
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b cpu_clk has been replaced by a set of divider and mux clocks.
meson_cpu_clk is no longer used and can be removed
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Instead of migrating meson cpu_clk to clk_regmap, like the other meson
clock drivers, we take advantage of the massive rework to get rid of it
completely, and solve (the first part) of the related FIXME notice.
As pointed out in the code comments, the cpu_clk should be modeled with
dividers and muxes it is made of, instead of one big composite clock.
The cpu_clk was not working correctly to enable dvfs on meson8b. It hangs
quite often when changing the cpu clock rate. This new implementation,
based on simple elements improves the situation but the platform will
still hang from time to time. This is not acceptable so, until we can
make the mechanism around the cpu clock stable, the cpu clock subtree
has been put in read-only mode, preventing any change of the cpu clock
The notifier and read-write operation will be added back when we have a
solution to the problem.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson audio divider driver to use clk_regmap and move gxbb
clock using meson_clk_audio_divider to clk_regmap.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson mpll driver to use clk_regmap and move meson8b, gxbb
and axg clocks using meson_clk_mpll to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock drivers are using struct parm to describe each field of the
clock provider. Providing helpers to access these fields with regmap
helps to keep drivers readable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_mux to clk_regmap
Also remove a few useless tables in the process
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_divider to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_gate to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
aoclk_gate_regmap has been replaced by meson's clk_regmap.
It is no longer necessary so, remove it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the gxbb ao specific regmap based clock and use the
meson clk_regmap based clock instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock controllers need to move the classical iomem registers to
regmap. This is triggered because the HHI controllers found on the GXBB
and GXL host more than just clocks. To properly handle this, we would
like to migrate HHI to syscon. Also GXBB AO clock controller already use
regmap, AXG AO and Audio clock controllers will as well.
The purpose of this change is to provide a common structure to these
meson controllers (and possibly others) for regmap based clocks.
This change provides the basic gate, mux and divider, based on the
helpers provided by the related generic clocks
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Over time things changes in CCF and issues have been fixed in meson
controllers.
Now, clk81 is decently modeled by read-only PLLs, a mux, a divider
and a gate. We can remove the FIXME comments related to clk81.
Also remove the comment about devm_clk_hw_register, as there is
apparently nothing wrong with it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We don't need several loop index variables in the probe function
This is far from being critical but since we are doing a vast
rework of meson clock controllers, now is the time to lower the
entropy a bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is no remove callbacks in meson's clock controllers and
of_clk_del_provider is never called if of_clk_add_hw_provider has been
executed, introducing a potential memory leak.
Fixing this by the using the devm variant.
In reality, the leak would never happen since these controllers are
never unloaded once in use ... still, this is worth cleaning.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The 'dev' pointer is directly available in gxbb and axg clock
controller, so consistently use it instead of going the through the
'pdev' pointer once in while
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is one of the differences between 6ul and 6ull: imx6ull has no sim
but has epdc and this clock is redefined on the same bit.
This can be verified in the Reference Manuals.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 81ac38847a ("clk: qcom: Add APCS clock controller support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
platform_get_resource() may return NULL, add proper check to
avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 4f16f7ff3b ("clk: hisilicon: Add support for Hi3660 stub clocks")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is now an helper function to round the rate when the
divider is read-only. Let's use it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a divider clock has CLK_DIVIDER_READ_ONLY set, it means that the
register shall be left un-touched, but it does not mean the clock
should stop rate propagation if CLK_SET_RATE_PARENT is set
This is properly handled in qcom clk-regmap-divider but it was not in
the generic divider
To fix this situation, introduce a new helper function
divider_ro_round_rate, on the same model as divider_round_rate.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-By: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clocks may need to initialize things, whatever it is, before
being able to properly operate. Move the .init() call before any
other callback, such recalc_rate() or get_phase(), so the clock
is properly setup before being used.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add helper functions for the translation between parent index and
register value in the generic multiplexer function. The purpose of
this change is avoid duplicating the code in other clock providers,
using the same generic logic.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Export clk_div_mask() in clk-provider header so every clock providers
derived from the generic clock divider may share the definition instead
of redefining it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If we try to determine the rate of a pass-through clock (a clock which
does not implement .round_rate() nor .determine_rate()),
clk_core_round_rate_nolock() will directly forward the call to the
parent clock. In the particular case where the pass-through actually
does not have a parent, clk_core_round_rate_nolock() will directly
return 0 with the requested rate still set to the initial request
structure. This is interpreted as if the rate could be exactly achieved
while it actually cannot be adjusted.
This become a real problem when this particular pass-through clock is
the parent of a mux with the flag CLK_SET_RATE_PARENT set. The
pass-through clock will always report an exact match, get picked and
finally error when the rate is actually getting set.
This is fixed by setting the rate inside the req to 0 when core is NULL
in clk_core_round_rate_nolock() (same as in __clk_determine_rate() when
hw is NULL)
Fixes: 0f6cc2b8e9 ("clk: rework calls to round and determine rate callbacks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fizV
-----END PGP SIGNATURE-----
Merge tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm into clk-fixes
Pull TI SoC clock fixes for 4.16 from Tero Kristo:
* tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm:
clk: ti: am43xx: add set-rate-parent support for display clkctrl clock
clk: ti: am33xx: add set-rate-parent support for display clkctrl clock
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c86 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJalfiVAAoJEFBXWFqHsHzOANUIAIaKIqpJOBfr8jiYgYOgPh++
1OJrOo8f6hEboe9egGZt0j80H6LhEFoU5u4c7hiWQ9o8cYf95uYiOMyvB8KZjSMj
vYZlchtNR3uC9Vqa5vF6CcHbTV8Ug67Wqar/OFkg7CAVGvVeetyKjgyLdDP+kj6w
IjNt3WDnE/Hf7n0NFT4TeHFABS6c6dRKeQrNrULg4/OkCdNDnFzEDw3tPrNdODaD
Kbu8zP7h1G3Ankr7/cXs5/9aMKe3eVaLSfxIybQx7P2d3+RQKFbt8FIs6KFuOCpe
AYgFPKqDPkM8BYh7P9BKIeKpuDf24ZfMI5gOGPa96AJRRgUP5wrcN9E7jibjkNI=
=Magi
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull i.MX clock fixes for 4.16 from Shawn Guo:
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c86 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
* tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx51-imx53: Fix UART4/5 registration on i.MX50 and i.MX53
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
-----BEGIN PGP SIGNATURE-----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=As0p
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes for 4.16 from Chen-Yu Tsai:
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
* tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks
Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
enabled by the bootloader.
Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.
Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.
Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.
This situation was found while adding fdiv_clk gates to the meson8b
platform. These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.
The situation is solved by reverting
commit f8f8f1d044 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.
Fixes: f8f8f1d044 ("clk: Don't touch hardware when reparenting during registration")
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLL_C_OUT_1 can't produce 216 MHz defined in the init_table. Let's
set it to 240 MHz and explicitly specify HCLK rate for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Machine dies if HCLK, SCLK or EMC is disabled. Hence mark these clocks
as critical.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
It's found that the final phase set by driver doesn't match that of
the output from clk_summary:
dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 346
mmc0: new ultra high speed SDR104 SDIO card at address 0001
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 0
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Fixes: 9e4d04adeb ("clk: add clk_core_set_phase_nolock function")
Cc: Stable <stable@vger.kernel.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
RCC manages clock for debug and trace.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Two micro-controller clock output (MCO) pins are available:
MCO1 and MCO2.
For each output, it is possible to select a clock source.
The selected clock can be divided thanks to configurable
prescaler.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each peripheral requires a bus interface clock.
Some peripherals need also a dedicated clock for their communication
interface, this clock is generally asynchronous with respect to the bus
interface clock (peripheral clock), and is named kernel clock.
For each IP, Peripheral clock and Kernel are generally gating with same
gate. Also, Kernel clocks can share a same multiplexer.
This patch introduces a mechanism to manage a gate with several
clocks and to manage a shared multiplexer (mgate and mmux).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds Kernel timers.
This patch adds timers kernel clock.
Timers are gather into two groups corresponding to the APB bus
they are attached to.
Each group has its own prescaler, managed in this patch.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC handles three sub-system clocks: ck_mpuss, ck_axiss
and ck_mcuss.
This patch adds also some MUX system and several prescalers.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each PLL has 3 outputs with post-dividers.
pll1_p is dedicated for Cortex-A7
pll1_q is not connected
pll1_r is not connected
pll2_p is dedicated for AXI
pll2_q is dedicated for GPU
pll2_r is dedicated for DDR
pll3_p is dedicated for mcu
pll3_q is for Peripheral Kernel Clock
pll3_r is for Peripheral Kernel Clock
pll4_p is for Peripheral Kernel Clock
pll4_q is for Peripheral Kernel Clock
pll4_r is for Peripheral Kernel Clock
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
STMP32MP1 has 4 PLLs.
PLL supports integer and fractional mode.
Each PLL has 3 output dividers (p, q, r)
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds source clocks for PLLs
This patch also introduces MUX clock API.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MP1 Gate is a gate with a set and a clear register.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Tegra210 has a hw bug which can cause IP blocks to lock up when ungating a
domain. The reason is that the logic responsible for resetting the memory
built-in self test mode can come up in an undefined state because its
clock is gated by a second level clock gate (SLCG). Work around this by
making sure the logic will get some clock edges by ensuring the relevant
clock is enabled and temporarily override the relevant SLCGs.
Unfortunately for some IP blocks, the control bits for overriding the
SLCGs are not in CAR, but in the IP block itself. This means we need to
map a few extra register banks in the clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
fixup mbist
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is needed by the memory built-in self test work around.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to id.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Certain clkctrl clocks, notably the display ones, use the
CLK_SET_RATE_PARENT feature extensively. Add support for this flag
to the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Currently, the driver contains a large hints table for clocks that exist
on a device, however, it is possible to probe the clocks from the firmware
also. Add support for this, and drop the clock hints table support from
the driver completely. This causes the driver to send a few extra sci-clk
messages during boot, basically one extra for each device that exists on
the SoC; on K2G this is approx 80.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the mux clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the divider clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Certain clocks require latching to be done, so that the actual
settings get updated on the HW that generates the clock signal.
One example of such a clock is the dra76x GMAC DPLL H14 output,
which requires its divider settings to be latched when updated.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Useful for changing few bits on a register, this makes sure for example
that the operation is done atomically in case of syscon.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Jerome Brunet