We only support x86 and ppc, due to the use of bus_to_virt() and friends.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Replace occurrences of the magic value ~(u64)0 for invalid
CSR address spaces by a named constant for better readability.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
The proper designator of an invalid CSR address is ~(u64)0, not (u64)0.
Use the correct value in initialization and deregistration.
Also, scsi_id->sbp2_lun does not need to be initialized twice.
(scsi_id was kzalloc'd.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
I've been experimenting to track down the cause of suspend/resume problems
on my Compaq Presario X1050 laptop:
http://bugzilla.kernel.org/show_bug.cgi?id=6075
Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.
I found that unloading the ohci1394 module before suspend and reloading it
after resume made the problem go away. Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:
PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was 2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was 0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was 0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was 1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was 20000100, writing 2000010a)
The default PCI driver performs the pci_restore_state when no driver is
loaded for the device. When the ohci1394 driver is loaded, it is supposed
to do this, however it appears not to do so.
I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded. I only added in the
pci_save_state and pci_restore_state - however, though I know little of
this hardware, surely the driver should really be doing more than this when
suspending and resuming? Currently it does almost nothing, what if there
are commands in progress, etc?
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@debian.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
It seems to have worked without the attribute during all the years
just because sizes of all struct members are multiples of 32 bits.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
It appears I will not get it fixed overnight.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
If sbp2 is forced to move data via ARM handler, the maximum packet size
allowed for S800 transfers exceeds ohci1394's buffer size on platforms
where PAGE_SIZE is 4096.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Being able to switch physical DMA on and off at run time would be a nice
feature but a PITA to support by highlevel drivers and userspace apps.
Therefore allow it only to be set when the driver is being loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch supplies the API extension introduced by patch
"ieee1394: extend lowlevel API for address range properties"
with proper addresses.
Like in patch ''ohci1394, sbp2: fix "scsi_add_device failed"
with PL-3507 based devices'', 1 TeraByte is chosen as physical
upper bound. This leaves a window for the middle address range.
This choice is only relevant for adapters which actually have a
programmable pysical upper bound register. (Only ALi and
Fujitsu adapters are known for this. Most adapters have a fixed
bound at 4 GB.) The middle address range is suitable for posted
writes.
AFAIK, PCILynx does not support physical DMA nor posted writes,
therefore no equivalent change in the pcilynx driver is necessary.
There is also a driver for GP2Lynx, although not in mainline Linux.
I assume this hardware does not support these OHCI features either.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Host adapter hardware imposes certain restrictions and features on
address ranges. Instead of hard-wire such ranges into the ieee1394
core or even into protocol drivers, let lowlevel drivers specify
these ranges via struct hpsb_host.
Patch "ohci1394: set address range properties" must be applied too,
else hpsb_allocate_and_register_addrspace() won't work properly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Since this is useful information, promote it from a debug macro to
a regular log message. The message appears only if the user set
exclusive_login=0, therefore won't clutter the logs in normal use.
Also update the comment on exclusive_login.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This code became ineffective a few Linux releases ago and is not
required anyway.
Note from Christoph Hellwig: scsi_cmnd.request_buffer is always a
scatterlist these days. Checking random bites into it and then
mangling the data in sbp2_check_sbp2_response will cause really bad
memory corruption when you're not lucky enough to have the check not
trigger by luck.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Since broadcast transactions are already complete when the request has
been sent, the same transaction label can be reused all over again, see
IEEE 1394 7.3.2.5 and 6.2.4.3. Therefore we can reduce the footprint
of struct hpsb_host by the size of one struct hpsb_tlabel_pool.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Add support for the following types of hardware:
+ nodes that have a link speed < PHY speed
+ 1394b PHYs that are less than S800 capable
+ 1394b/1394a adapter cable between two 1394b PHYs
Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised.
A probing function is added to nodemgr's config ROM fetching routine
which adjusts the allowable speed if an access problem was encountered.
Pros and Cons of the approach:
+ minimum code footprint to support this less widely used hardware
+ nearly no overhead for unaffected hardware
- ineffective before nodemgr began to read the ROM of affected nodes
- ineffective if ieee1394 is loaded with disable_nodemgr=1
The speed map CSRs which are published to the bus are not touched by the
patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Hakan Ardo <hakan@debian.org>
Cc: Calculex <linux@calculex.com>
Cc: Robert J. Kosinski <robk@cmcherald.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch modifies the ohci1394.c file to enable and manage the "cycle too
long" interrupt.
If this interrupt occurs, the "LinkControl.CycleMaster" bit of the host
controller is reseted. This implies, that the host controller does not send
"cycle start" packet anymore freezing then the isochronous communication.
The management of the interrupt added by the patch is that when the interrupt
occurs, the OHCI irq handler prints a kernel log warning and then sets the
"LinkControl.CycleMaster" bit again resuming the isochronous communication.
Signed-off-by: Jean-Baptiste Mur <jeanbaptiste@maunakeatech.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
The workarounds are not required for DViCO Momobay FX-3A and AFAIR not
for Momobay CX-2. These contain an TSB42AA9A but feature the same
firmware_revision value as the older DViCO Momobay CX-1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
spotted by Adrian Bunk. Also remove some superfluous comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
when attempting to find the 'last' part of the dma region continue the
search from where we left off, instead of starting the search over.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
When working with multiple cameras and intensive applications, our logs
get flooded with video1394 information which isn't of much interest.
Any objections to demoting these messages to debug messages?
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
People have been reporting that PPP connections over ptys, such as
used with PPTP, will hang randomly when transferring large amounts of
data, for instance in http://bugzilla.kernel.org/show_bug.cgi?id=6530.
I have managed to reproduce the problem, and the patch below fixes the
actual cause.
The problem is not in fact in ppp_async.c but in n_tty.c. What
happens is that when pptp reads from the pty, we call read_chan() in
drivers/char/n_tty.c on the master side of the pty. That copies all
the characters out of its buffer to userspace and then calls
check_unthrottle(), which calls the pty unthrottle routine, which
calls tty_wakeup on the slave side, which calls ppp_asynctty_wakeup,
which calls tasklet_schedule. So far so good. Since we are in
process context, the tasklet runs immediately and calls
ppp_async_process(), which calls ppp_async_push, which calls the
tty->driver->write function to send some more output.
However, tty->driver->write() returns zero, because the master
tty->receive_room is still zero. We haven't returned from
check_unthrottle() yet, and read_chan() only updates tty->receive_room
_after_ calling check_unthrottle. That means that the driver->write
call in ppp_async_process() returns 0. That would be fine if we were
going to get a subsequent wakeup call, but we aren't (we just had it,
and the buffer is now empty).
The solution is for n_tty.c to update tty->receive_room _before_
calling the driver unthrottle routine. The patch below does this.
With this patch I was able to transfer a 900MB file over a PPTP
connection (taking about 25 minutes), whereas without the patch the
connection would always stall in under a minute.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock,
which can lead to all sorts of interesting scenarios.
This whole error-handling portion of sata_mv is nasty (and will get fixed for
the new EH stuff), but for now this patch will help keep it on life-support.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Christoph Lameter <clameter@sgi.com>
Looks like a comma was left from the conversion from a struct to an
assignment.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to Intel ICH spec, there are several rules that Base Address
should be programmed before IOSE (PCICMD register ) enabled.
For example ICH7:
12.1.3 SATA : the base address register for the bus master register
should be programmed before this bit is set.
11.1.3: PCICMD (USB): The base address register for USB should be
programmed before this bit is set.
....
To make sure kernel code follow this rule , and prevent unnecessary
confusion. I proposal this patch.
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least one laptop blew up on resume from suspend with a black screen due
to a lack of this patch. By only writing back config space that is
different, we minimise the possibility of accidents like this.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently don't handle errors properly when resuming a PCI device:
* In pci_default_resume() we capture the error code returned by
pci_enable_device() but don't pass it up to the caller.
Introduced by commit 95a629657d
* In pci_resume_device(), the errors possibly returned by the driver's
.resume method or by the generic pci_default_resume() function are
ignored.
This patch fixes both issues.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_ACPI not defined
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets the max_cache_size value required to tune up
scheduler in SMP systems. Otherwise, the calculated
migration_cost is too high and task scheduling may lock up.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Avoid JBUS errors on some Niagara systems.
[FUSION]: Fix mptspi.c build with CONFIG_PM not set.
[TG3]: Handle Sun onboard tg3 chips more correctly.
[SPARC64]: Dump local cpu registers in sun4v_log_error()
From: Milton Miller <miltonm@bga.com>
The add_preferred_console call in rtas_console.c was not causing the
console to be selected. It turns out that the add_preferred_console was
being called after the hvc_console driver was registered. It only works
when it is called before the console driver is registered.
Reorder hvc_console.o after the hvc_console drivers to allow the selection
during console_initcall processing.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Markus Lidel <Markus.Lidel@shadowconnect.com>
- Fixed locking of struct i2o_exec_wait in Executive-OSM
- Removed LCT Notify in i2o_exec_probe() which caused freeing memory and
accessing freed memory during first enumeration of I2O devices
- Added missing locking in i2o_exec_lct_notify()
- removed put_device() of I2O controller in i2o_iop_remove() which caused
the controller structure get freed to early
- Fixed size of mempool in i2o_iop_alloc()
- Fixed access to freed memory in i2o_msg_get()
See http://bugzilla.kernel.org/show_bug.cgi?id=6561
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Work around the oops reported in
http://bugzilla.kernel.org/show_bug.cgi?id=6478.
Thanks to Ralf Hildebrandt <ralf.hildebrandt@charite.de> for testing and
reporting.
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: David Howells <dhowells@redhat.com>
Apply some alterations to the memory barrier document that I worked out
with Paul McKenney of IBM, plus some of the alterations suggested by Alan
Stern.
The following changes were made:
(*) One of the examples given for what can happen with overlapping memory
barriers was wrong.
(*) The description of general memory barriers said that a general barrier is
a combination of a read barrier and a write barrier. This isn't entirely
true: it implies both, but is more than a combination of both.
(*) The first example in the "SMP Barrier Pairing" section was wrong: the
loads around the read barrier need to touch the memory locations in the
opposite order to the stores around the write barrier.
(*) Added a note to make explicit that the loads should be in reverse order to
the stores.
(*) Adjusted the diagrams in the "Examples Of Memory Barrier Sequences"
section to make them clearer. Added a couple of diagrams to make it more
clear as to how it could go wrong without the barrier.
(*) Added a section on memory speculation.
(*) Dropped any references to memory allocation routines doing memory
barriers. They may do sometimes, but it can't be relied on. This may be
worthy of further documentation later.
(*) Made the fact that a LOCK followed by an UNLOCK should not be considered a
full memory barrier more explicit and gave an example.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doing PCI config space accesses to non-present PCI slots
can result in fatal JBUS errors if the PCI config access
hypervisor call is performed on cpus other than the boot
cpu.
PCI config space accesses to present PCI slots works just
fine.
Recursively traverse the OBP device tree under the PCI
controller node and record all present device IDs into
a small hash table.
Avoid the hypervisor call for any PCI config space access
attempt for a device not recorded in the hash table.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of all the SUN_570X logic and instead:
1) Make sure MEMARB_ENABLE is set when we probe the SRAM
for config information. If that is off we will get
timeouts.
2) Always try to sync with the firmware, if there is no
firmware running do not treat it as an error and instead
just report it the first time we notice this condition.
3) If there is no valid SRAM signature, assume the device
is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT.
Update driver version and release date.
With help from Michael Chan and Fabio Massimo Di Nitto.
Signed-off-by: David S. Miller <davem@davemloft.net>
The IBM Cell blade firmware might confuse the kernel to think it's a
pSeries machine. This fixes it for now. With a bit of luck, the firmware
will be updated to avoid that in the future but currently that patch is
needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in prom_init.c calling the firmware
ibm,client-architecture-support method on pSeries has a bug where it
fails to properly pass the instance handle of the firmware object when
trying to call a method. Result ranges from the call doing nothing to
the firmware crashing. (Found by Segher, thanks !)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug found by Dave Jones that means that it is possible
for userspace to provoke a machine check on 32-bit kernels. This
also fixes a couple of other places where I found similar problems
by inspection.
Signed-off-by: Paul Mackerras <paulus@samba.org>
From: Martin Schwidefsky <schwidefsky@de.ibm.com>
__futex_atomic_op needs to do an atomic operation in the user address space,
not the kernel address space. Add the missing sacf 256/sacf 0 to switch to
the secondary mode before doing the compare-and-swap. In addition add
another fixup for catch specification exceptions if the compare-and-swap
address is not aligned.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ben Collins