Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to e1000, e1000e and igb.
Joern Engel fixes up the e1000 driver to reduce scheduler latencies by
making the eeprom read/write functions scheduler friendly by using a mutex
lock instead of a spin lock.
Todd adds code for igb to initialize the 88E1543 PHY properly. Then fixed
igb to use the correct i210 register for EEMNGCTL, since the i210 has two
EEPROM access registers (EEARBC and EEMNGCTL).
Dmitry Vyukov provides a fix for e1000 to resolve a data race found with
KernelThreadSanitizer (KTSAN), where no memory barriers were being used
when buffers get recycled, so the recycled buffers can be corrupted. So
use smp_store_release() to update tx_ring->next_to_clean and
smp_load_acquire() to read tx_ring->next_to_clean to properly hand off
buffers from e1000_clean_tx_irq() to e1000_xmit_frame().
Jarod Wilson fixes igb so that we do not try to unmap a NULL hw_addr. Then
cleaned up array_rd32() so that it uses igb_rd32() the same as rd32() and
use io_addr() in more places so that we do not have to call E1000_REMOVED().
Janusz Wolak cleans up the e1000 driver by correcting warnings produced
by checkpatch.pl for the driver.
Jean Sacren provides several patches with general cleanups for e1000 and
e1000e, which include code comment fix-ups and cleanup of local variables
not needed.
Dmitry Fleytman fixes a possible division by zero in the receive interrupt
handler for e1000e when working without adaptive interrupt moderation,
which is typically disabled on jumbo MTUs.
Raanan increases the timeout of the polling bit due to timing changes to
the ME firmware on a platform, so increase the timeout to 300ms. Added
initial support for i219-LM, which is a LOM that will be available on
systems with the Lewisburg Platform Controller HUB (PCH) chipset.
Jan Beulich fixes a NULL dereference in igb, due to the adapter->vf _data
being NULL while adapter->vfs_allocated_count is non-zero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The combined effect of commits 6423fc3416 ("igb: do not re-init SR-IOV
during probe") and ceee3450b3 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using goto statement, we can achieve sharing the same exit path so
that code duplication could be minimized.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to historical reason, 'phy_data' has never been included in the
kernel doc. Fix it so that the requirement could be fulfilled.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use 'That' to replace 'The' so that the comment would make sense.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The checking logic needed some clean-up work, so we rewrite it by
checking for break first. With that change in place, we can even move
the second check for goto statement outside of the loop.
As this is merely a cleanup, no functional change is involved. The
questionable 'tmp != 0xFF' is intentionally left alone.
Mark Rustad and Alexander Duyck contributed to this patch.
CC: Mark Rustad <mark.d.rustad@intel.com>
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman.aud@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Janusz Wolak <januszvdm@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean,
then e1000_xmit_frame reuses the cleaned buffers. But there are no
memory barriers when buffers gets recycled, so the recycled buffers
can be corrupted.
Use smp_store_release to update tx_ring->next_to_clean and
smp_load_acquire to read tx_ring->next_to_clean to properly
hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was responsible for ~150ms scheduler latencies.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Generate version strings like the PF driver does. This gives us more
flexibility to add suffixes to the version string at build time.
Change-ID: I0a5ca0783dd8fb849516bfc1e37ea070127847bd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch with X722 devices, driver will set wrong PCTYPES
for VF and UDP flows will not fan out.
Change-ID: I04fe4988253b7cd108c9179a643c969764efcb76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.
Since these messages are really for debugging purposes, reclassify
them as such.
Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.
Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.
Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.
Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to ixgbe only.
Alex Duyck provides almost off of the changes in this series. First, add a
check to make sure mac_table was actually allocated and is not NULL to
ensure we do not get a NULL pointer dereference further down the line.
Fixed SR-IOV VLAN pool configuration since the code for checking the PF bit
in ixgbe_set_vf_vlan_msg() was using the wrong offset. Cleanup/simplify
the logic for setting the VFTA register by removing the number of
conditional checks needed. Fixed a number of issues within the VLVF and
VLFB configuration by simplifying the code. Added support for bypassing
the VLVF entry creation when the PF is adding a new VLAN. Reduced the
complexity of the search function used for finding a VLVF entry associated
with a given VLAN ID. Added support for VLAN promiscuous with SR-IOV
enabled by setting all the bits in the VFTA and all of the VLVF bits
associated with teh pool belonging to the PF, in addition to cleaning up
those same bits in the event of promiscuous mode being disabled. Fixed
and issue where we ran the risk of leaking an address into pool 0 which
really belongs to VF 0 when SR-IOV is enabled.
Emil fixes an issue with some X550 devices which can connect at 2.5Gbps,
but only with certain link partners during fail-over, so to avoid
confusion, we do not report it as supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some X550 devices can connect at 2.5Gbps during fail-over, but only
with certain link partners. Also setting the advertised speed will
not work so we do not report it as supported to avoid confusion.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to. What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.
Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface. Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry. What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLAN promiscuous with SR-IOV enabled.
The code prior to this patch was only adding the PF to VLANs that the VF
had added. As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited. This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.
With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF. By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF. In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to reduce the complexity of the search function used
for finding a VLVF entry associated with a given VLAN ID. The previous
code was searching from bottom to top. I reordered it to search from top
to bottom. In addition I pulled an AND statement out of the loop and
instead replaced it with an OR statement outside the loop. This should
help to reduce the overall size and complexity of the function.
There was also some formatting I cleaned up in regards to whitespace and
such.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues within the VLVF and VLVFB
configuration
First was the fact that code was overly complicated with multiple
conditional paths depending on if we adding or removing and which bit we
were going to add or remove. Instead of messing with all that I have
simplified it by using (vid / 32) and (1 - vid / 32) to identify our
register and the other vlvfb register.
Second was the fact that we were likely leaking a few packets into the PF
in cases where we were deleting an entry and the VFTA filter for that entry
as the ordering was such that we deleted the pool and then the VLAN filter
instead of the other way around. I have updated that by adding a check for
no bits being set and if that occurs we clear things up in the proper
order.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to clear the way for upcoming work I thought it best to drop the
level of indent in the ixgbe_set_vfta_generic function. Most of the code
is held in the virtualization specific section. So the easiest approach is
to just add a jump label and jump past the bulk of the code if it is not
enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the logic for setting the VFTA register by removing
the number of conditional checks needed. Instead we just use some boolean
logic to generate vfta_delta, and if that is set then we xor the vfta by
that value and write it back.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sensor index should be passed instead of 0. For now, this does not make
a difference, since there is so far only one temperature sensor
exposed by HW.
Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix copy & paste error in MTPM unpack helper.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename en_flow_table.c to en_fs.c in order to be aligned
with the new flow steering files.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the new flow steering API and remove the old
one.
Few changes are required:
1. The Ethernet flow steering follows the existing implementation, but uses
the new steering API. The old flow steering implementation is removed.
2. Move the E-switch FDB management to use the new API.
3. When driver is loaded call to mlx5_init_fs which initialize
the flow steering tree structure, open namespaces for NIC receive
and for E-switch FDB.
4. Call to mlx5_cleanup_fs when the driver is unloaded.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering initialization is based on static tree which
illustrates the flow steering tree when the driver is loaded. The
initialization considers the max supported flow table level of the device,
a minimum of 2 kernel flow tables(vlan and mac) are required to have
kernel flow table functionality.
The tree structures when the driver is loaded:
root_namespace(receive nic)
|
priority-0 (kernel priority)
|
namespace(kernel namespace)
|
priority-0 (flow tables priority)
In the following patches, When the EN driver will use the flow steering
API, it create two flow tables and their flow groups under
priority-0(flow tables priority).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the following objects:
mlx5_flow_root_namespace: represent the root of specific flow table
type tree(e.g NIC receive, FDB, etc..)
mlx5_flow_group: define the mask of the flow specification.
fs_fte(flow steering flow table entry): defines the value of the
flow specification.
The following describes the relationships between the tree objects:
root_namespace --> priorities -->namespaces -->
priorities -->flow-tables --> flow-groups -->
flow-entries --> destinations
When we create new object(flow table/flow group/flow table entry), we
call to the FW command and then we add the related sw object to the tree.
When we destroy object, e.g. call to mlx5_destroy_flow_table, we use
the tree node destructor for destroying the FW object and remove the
node from the tree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the flow steering mlx5_flow_namespace (Namespace)
and fs_prio (Flow Steering Priority) tree nodes.
Namespaces are used in order to isolate different usages or types
of steering (for example, downstream patches will add a different
namespaces for the NIC driver and for E-Switch FDB usages).
Flow Steering Priorities are objects that describes priorities
ranges between different flow objects under the same namespace.
Example, entries in priority i are matched before entries
in priority i+1.
This patch adds the following algorithms:
1) Calculate level:
Each flow table has level(the priority between the flow tables).
When we initialize the flow steering tree, we assign range of levels
to each priority, therefore the level for new flow table is
the location within the priority related to the range of the priority.
2) Match between match criteria. This function is used
for searching flow group when new flow rule is added.
3) Match between match values. This function is used
for searching flow table entry when new flow rule is added.
4) Add essential macros for traversing on a node's children.
E.g. traversing on all the flow table of some priority
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the base data structure and its operations that are
going to represent ConnectX-4 Flow Steering, this data structure
is basically a tree and all Flow steering objects such as
(Flow Table/Flow Group/FTE/etc ..) are represented as fs_node(s).
fs_node is the base object which describes a basic tree node, with the
following extra info:
type: describes the runtime type of the node (Object).
lock: lock this node sub-tree.
ref_count: number of children + current references.
remove_func: a generic destructor.
fs_node types will be used and explained once the usage is added in the
following patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under SRIOV there might be a case where VFs are loaded
without pre-assigned MAC address. In this case, the VF
will randomize its own MAC. This will address the case
of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch capabilities should be queried only if E-Switch flow table
is supported and not only when vport group manager.
Fixes: d6666753c6 ("net/mlx5: E-Switch, Introduce HCA cap and E-Switch vport context")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is introduced in pass-2 chip and with this CQ interrupt
coalescing will work based on both timer and count.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading TCP segmentation to HW in pass-2
revision of hardware. Both driver level SW TSO for pass1.x chips
and HW TSO for pass-2 chip will co-exist. Modified SQ descriptor
structures to reflect pass-2 hw implementation.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch each CPU is associated with its own set of TX queues.
It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err = " assignment is missing here.
Fixes: 0d65fc1304 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.
Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21: expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21: got restricted __le32 *<noident>
This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]
This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.
Looking at that code in more detail to fix the warnings, I see multiple
related problems:
* The conversion functions are not endian-safe, as the DMA descriptors
are almost certainly fixed-endian, but the CPU is not.
* On 64-bit machines, passing a pointer through a u32 variable is a
bug, accessing an indirect pointer as a u32 pointer even more so.
* The handling of epib and psdata mixes native-endian and device-endian
data.
In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cmac_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb90 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc69fdfc6c
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a106 ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WR headers may not fit within one descriptor.
So we need to deal with wrap-around here.
Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time. The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.
Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mm[cd]_ctrl() and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a mis-order in mlx4 log. Fix it.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have moved on to using allocated pages to carve receive
buffers instead of netdev_alloc_skb() there is no need to store
any pointers for later retrieval. Earlier we had to store
skb and skb->data pointers which later are used to handover
received packet to network stack.
This will avoid an unnecessary cache miss as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same switch-case repeates for nivc_*_intr functions.
In this patch it is moved to a helper nicvf_int_type_to_mask().
By the way:
- Unneeded write to NICVF register dropped if int_type is unknown.
- netdev_dbg() is used instead of netdev_err().
Signed-off-by: Yury Norov <yury.norov@auriga.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Acked-by: Vadim Lomovtsev <Vadim.Lomovtsev@caiumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 driver runs in HA mode, and all VFs are single ported
ones, we make their single port Highly-Available.
This is done by taking advantage of the HA mode properties (following
bonding changes with programming the port V2P map, etc) and adding
the missing parts which are unique to SRIOV such as mirroring VF
steering rules on both ports.
Due to limits on the MAC and VLAN table this mode is enabled only when
number of total VFs is under 64.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource, unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.
Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code reading the MAHR/MALR registers in read_mac_address() is terribly
ineffective -- it reads MAHR 4 times and MALR 2 times, while it's enough to
read each register only once. Use the local variables to achieve that,
somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code reading the MAHR/MALR registers in ravb_read_mac_address() is
terribly ineffective -- it reads MAHR 4 times and MALR 2 times, while
it's enough to read each register only once. Use the local variables to
achieve that, somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'flags' field in bnx2x_stats_arr[] serves only one purpose - to tell
us if the statistic is a per-port stat and thus should not be shown for
virtual functions. It's strange that the field can have three different
values. A boolean will do just fine.
Also remove IS_FUNC_STAT(). It was used only once and it's in fact just
a negation of IS_PORT_STAT().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in MCFW behaviour means that the net driver must update its record
of the warm_boot_count by reading it from the ER_DZ_BIU_MC_SFT_STATUS
register.
On v4.6.x MCFW the global boot count was incremented when some functions
needed to be reset to enable multicast chaining, so all functions saw the
same value. In that case, the driver needed to increment its
warm_boot_count when other functions were reset, to avoid noticing it later
and then trying to reset itself to recover unnecessarily.
With v4.7+ MCFW, the boot count in firmware doesn't change as that is
unnecessary since the PFs that have been reset will each receive an MC
reboot notification. In that case, the driver re-reads the unchanged
value.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx queue #1 frame error counter name contains trailing underscore,
probably due to a typo...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe, i40e/i40evf, MAINTAINERS and e100.txt
Alex provides a fix for ixgbe where enabling SR-IOV and then bringing the
interface up was resulting in the PF MAC addresses getting into a bad state.
The workaround for this issue is to bring up the interface first and then
enable SR-IOV as this will trigger the reset in the existing code.
I clean up legacy license stuff in the e100.txt documentation and then
update the maintainers/reviewers list for our drivers.
Jesse fixes an issue with the i40e/i40evf drivers, where if the driver were
to happen to have a mutex held while the i40e_init_adminq() call was called,
the init_adminq might inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.
This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.
This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.
Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the initializzation code to disable the hardware
vlan support for VLAN Tag stripping by default for now.
Proper support of "hardware VLAN assitance" feature would
soon come in the next coming patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of ethtool TSO option to support
Hip06 SoC to HNS
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "TSO (TCP Segment Offload)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
Enabling this feature would help offload the TCP Segmentation
process to the Hip06 ethernet hardware. This eventually would help
in saving precious cpu cycles.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "RSS (Receive Side Scaling)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
This feature helps in distributing the different flows (mapped as
hash by hardware using Toeplitz Hash) to different Queues asssociated
with the processor cores. The mapping of flow-hash values to the
different queues is stored in indirection table (which is per Packet-
parse-Engine/PPE). This patch also provides the changes to re-program
the (flow-hash<->Qid) mapping using the ethtool.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support of Hisilicon Hip06 SoC to the existing HNS
ethernet driver.
The changes in the driver are mainly due to changes in the DMA
descriptor provided by the Hip06 ethernet hardware. These changes
need to co-exist with already present Hip05 DMA descriptor and its
operating functions. The decision to choose the correct type of DMA
descriptor is taken dynamically depending upon the version of the
hardware (i.e. V1/hip05 or V2/hip06, see already existing
hisilicon-hns-nic.txt binding file for detailed description). other
changes includes in SBM, DSAF and PPE modules as well. Changes
affecting the driver related to the newly added ethernet hardware
features in Hip06 would be added as separate patch over this and
subsequent patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Better to just warn the user that something really odd is going on and
continue to run.
Suggested-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically we return error pointers when we want to use those
pointers in the non-error case, but this function is just
returning error pointers or NULL for success. Change the style to
plain int to follow normal kernel coding styles.
Cc: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation
is to modify the device tree.
This is needed if you plan to use the same kernel with
different ethernet switches, the ones that support the in-band
status and the ones that not.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves autoneg-related bit manipulations to the single place.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fallback compatibility strings for R-Car Gen 2 & 3 SoC Families.
This is in keeping with the fallback scheme being adopted wherever appropriate
for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes PTP support active in CONFIG mode on R-Car Gen3.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Virtual Functions for the Netronome's
NFP-4000 and NFP-6000 based NICs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Rolf Neugebauer <rolf.neugebauer@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to i40e and i40evf only.
Mitch updates the i40evf driver by increasing the maximum number of queues,
since future devices will allow for more queue pairs. Cleans up a
duplicate printing of the driver info string done in init, since it is
already done in probe. Cleaned up the several allocations which did
not need to be at atomic level, where GFP_KERNEL would work just fine.
Then makes i40e_sync_vsi_filters() a more mature function, make having
a common exit point so it will properly release the busy lock on the VSI
and propagate errors to the callers. Then does some whitespace
housekeeping in i40evf.
Kiran moves and updates the detection/recovery of transmit queue hang code
to service_task from tx_timeout function. Also fixed memory leak when
users program flow-director filter using ethtool (sideband filter
programming), the cause being the check of 'tx_buffer->skb' was preventing
'raw_buf' from being freed as part of the cleanup.
Jesse enabled the ability to turn off/on packet split using ethtool priv
flags. Then does some housekeeping for both the i40e and i40evf drivers
which includes: remove unused/useless code, correct whitespace, remove
duplicate #include, fix incorrect comment, etc...
Neerav cleans up functions to gather Flow Control Rx XOFF stats, since
the recent change in the driver logic for checking transmit hang has been
moved, so these functions do not do anything meaningful any longer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement and enable SR-IOV ndos to manage SR-IOV configuration via
netdev netlink API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get VF statistics using query vport
counter command.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add query and modify functions to control client vlan and qos
striping or insertion, in E-Switch vports contexts.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch vport context is unlike NIC vport context, managed by the
E-Switch manager or vport_group_manager and not by the NIC(VF) driver.
The E-Switch manager can access (read/modify) any of its vports
E-Switch context.
Currently E-Switch vport context includes only clietnt and server
vlan insertion and striping data (for later support of VST mode).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set VF mac/link state and query VF config
to be used later in nedev VF ndos or any other management API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling E-Switch SRIOV for nvfs+1 vports.
Create E-Switch FDB for L2 UC/MC mac steering between VFs/PF and
external vport (Uplink).
FDB contains forwarding rules such as:
UC MAC0 -> vport0(PF).
UC MAC1 -> vport1.
UC MAC2 -> vport2.
MC MACX -> vport0, vport2, Uplink.
MC MACY -> vport1, Uplink.
For unmatched traffic FDB has the following default rules:
Unmached Traffic (src vport != Uplink) -> Uplink.
Unmached Traffic (src vport == Uplink) -> vport0(PF).
FDB rules population:
Each NIC vport (VF) will notify E-Switch manager of its UC/MC vport
context changes via modify vport context command, which will be
translated to an event that will be handled by E-Switch manager (PF)
which will update FDB table accordingly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define needed hardware structures and capabilities needed
for E-Switch FDB flow tables and read them on driver load.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch is the software entity that represents and manages ConnectX4
inter-HCA ethernet l2 switching.
E-Switch has its own Virtual Ports, each Vport/vNIC/VF can be
connected to the device through a vport of an e-switch.
Each e-switch is managed by one vNIC identified by
HCA_CAP.vport_group_manager (usually it is the PF/vport[0]),
and its main responsibility is to forward each packet to the
right vport.
e-Switch needs to manage its own l2-table and FDB tables.
L2 table is a flow table that is managed by FW, it is needed for
Multi-host (Multi PF) configuration for inter HCA switching between
PFs.
FDB table is a flow table that is totally managed by e-Switch driver,
its main responsibility is to switch packets between e-Swtich internal
vports and uplink vport that belong to the same.
This patch introduces only e-Swtich l2 table management, FDB managemnt
will come later when ethernet SRIOV/VFs will be enabled.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each Vport/vNIC must notify underlying e-Switch layer
for vlan table changes in-order to update SR-IOV FDB tables.
We do that at vlan_rx_add_vid and vlan_rx_kill_vid ndos.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each Vport/vNIC must notify underlying e-Switch layer
for UC/MC list and promisc mode updates, in-order to update
l2 tables and SR-IOV FDB tables.
We do that at set_rx_mode ndo.
preperation for ethernet-SRIOV and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) vlan table changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) promisc mode changes.
Preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
manager (PF) to configure its VFs link states in e-switch
preparation for ethernet sriov.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those functions are needed to notify the upcoming L2 table and SR-IOV
E-Switch(FDB) manager(PF), of the NIC vport (vf) UC/MC mac lists
changes.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for SR-IOV we add here an API to enable each e-switch
client (PF/VF) to configure its L2 MAC addresses and for the e-switch
manager (usually the PF) to access them in order to be able to
configure them into the e-switch.
Therefore we now pass vport num parameter to
mlx5_query_nic_vport_context, so PF can access other vports contexts.
preperation for ethernet sriov and l2 table management.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SRIOV base support for mlx5 supported devices. The same
driver is used for both PFs and VFs; VFs are identified by the driver
through the flag MLX5_PCI_DEV_IS_VF added to the pci table entries.
Virtual functions are created as usual through writing a value to the
sriov_numvs sysfs file of the PF device. Upon instantiating VFs, they will
all be probed by the driver on the hypervisor. One can gracefully unbind
them through /sys/bus/pci/drivers/mlx5_core/unbind.
mlx5_wait_for_vf_pages() was added to ensure that when a VF dies without
executing proper teardown, the hypervisor driver waits till all of the
pages that were allocated at the hypervisor to maintain its operation
are returned.
In order for the VF to be operational, the PF needs to call enable_hca
for it. This can be done before the VFs are created through a call to
pci_enable_sriov.
If the there are VFs assigned to a VMs when the driver of the PF is
unloaded, all the VF will experience system error and PF driver unloads
cleanly; in this case pci_disable_sriov is not called and the devices
will show when running lspci. Once the PF driver is reloaded, it will
sync its data structures which maintain state on its VFs.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify these functions to have func_id argument to state which device we
are referring to. This is done as a preparation for SRIOV support where
a PF driver needs to control its virtual functions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reasonably sure this doesn't serve any purpose.
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling/disabling TX on a LAG port means enabling/disabling distribution
in our HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement FDB offloading for lagged ports, including learning LAG FDB
entries, adding/removing static FDB entries and dumping existing LAG FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement basic procedures for joining/leaving port to/from LAG. That
includes HW setup of collector, core LAG mapping setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG-related records have specific format in SFN register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG-related records have specific format in SFD register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of SLDR, SLCR2, SLCOR registers that are used to
configure LAG.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion queue element for receive queue provides information if the
packet was received via LAG port. Extract this info and pass it along
to core.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower layer (pci) has information if the packet is received via LAG port.
If that is the case, it fills up rx_info accordingly. However upper
layer does not care about lag_id/port_index for received packets so
convert it to local_port before passing it up. For that conversion, lag
mapping array is introduced. Upper layer is responsible for setting up
the mapping according to what is set in HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add just a stub for now. This allows to pass check in dev_ifsioc,
SIOCADDMULTI and SIOCDELMULTI cases. Teamd is using these to add LACP
slow MAC.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fd89545f3 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) remove duplicate include of tcp.h
2) put an ampersand at the end of a line instead of the beginning
3) remove a useless dev_info
4) match declaration of function to the implementation
5) repair incorrect comment
6) correct whitespace
7) remove unused define
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't be using a bitwise operator here; it's not a bitwise
operation. Use a logical operator instead. Why doesn't c have a
logical-or-and-assign operator?
Change-ID: Id84f3ca884910bed7073c84b1e16a102e958d0de
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Operators should have spaces around them.
Change-ID: I64735e9aa8618b9a5059a87ace1c999d6d3bfcfb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The separate functions to gather Flow control Rx XOFF stats was to
determine if the Tx for a queue was paused due to Link Flow Control(LFC)
or Priority Flow Control(PFC).
But, with recent change in the i40e driver the logic for checking th Tx
hang has been removed and these functions don't do anything meaningful.
Hence, there is no need to keep these separate functions to gather Rx
XOFF stats for LFC or PFC.
This patch removes these functions and moves the stat collection for
XOFF Rx to the i40e_update_pf_stats() that collects all the PF stats.
Change-ID: Iec1452dac3a6766f0d968e754cb407530d7c60cd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of having our own custom symbol, we can just rely
on whether or not the kernel has the feature enabled.
In this case use IS_ENABLED(CONFIG_VXLAN) in order to handle
built-in or module in the current BKM way.
Change-ID: I5890fbb518ff8ed6bb07c3362fb0a8a829f9b241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool priv flags implementation to enable or disable packet split, which
is a hardware feature that inspects headers and will put headers in a
separate DMA buffer from the payload data. The driver was automatically
choosing to enable packet split in some cases and this gives the user the
ability to turn it off/on explicitly.
to query state:
ethtool --show-priv-flags ethx
to enable:
ethtool --set-priv-flags ethx packet-split on
to disable:
ethtool --set-priv-flags ethx packet-split off
Why would anyone want this?
Because some environments benefit from header/data split in the receive
buffer, and the driver defaults to one or the other depending on
environment/kernel parameters.
Why didn't you implement a generic ethtool control for this feature?
Because Intel hardware is the only hardware that supports header/data
split.
Change-ID: I803121e1eecc9ccb2884031fd85dd1110b3af66d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't use uint32_t type the kernel. Use u32 instead. No functional
change.
Change-ID: I77bbf3b6464edaef747c7104b43534032a4dba63
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These allocations don't need to be at atomic level. GFP_KERNEL is fine
and they'll reduce stress on the allocator when the system is starved
for memory.
Change-ID: I3561d0399a681de0ad25291b6c848b224c1fde12
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the memory leak which would be seen otherwise when user
programs flow-director filter using ethtool (sideband filter programming).
When ethtool is used to program flow directory filter, 'raw_buf' gets
allocated and it is supposed to be freed as part of queue cleanup. But
check of 'tx_buffer->skb' was preventing it from being freed.
Change-ID: Ief4f0a1a32a653180498bf6e987c1b4342ab8923
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains following changes:
- detection and recovery logic (issue SW interrupt) has been moved to
service_task from timeout function.
- added some more debug info from tx_timeout.
Logic to detect and recover TX queue hung is now two step process:
- service_task detects TX queue hung and sets a bit(hung_detected) if
it was not set.
- if bit was set (means this is back-back hung condition detected),
issue SW interrupt and clear the bit.
- napi_poll clears the bit unconditionally since it cleans TX/RX queues.
Change-ID: Ieed03a48927c845a988b3ff375090bf37caeb903
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already print the driver info string in probe, so don't print
it again in init. No need to repeat. No need to repeat.
Change-ID: Ief597997f580a8c54d5950e3a84c29f2075be66b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the helper function to set the real number of RX queues, and also
set the real number of TX queues.
Change-ID: I67982799de3f248fb4158ccdc9b1a74385f42ddd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Future devices will allow for more queue pairs, so allocate a netdev
that can handle them. While we're at it, get rid of the separate
MAX_TX/MAX_RX defines. Since we always get matched queue pairs, having
these makes no sense.
Change-ID: I0e3556cd9a962506e509eb7c0afa36b329e8cb51
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e328941 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of awkwardly keeping a fixed array of pointers in the adapter
struct and then allocating ring structs individually, just keep a single
pointer and allocate a single blob for the arrays. This simplifies code,
shrinks the adapter structure, and future-proofs the driver by not
limiting the number of rings we can handle.
Change-ID: I31334ff911a6474954232cfe4bc98ccca3c769ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the queue_vector array from a statically-sized member of the
adapter structure to a dynamically-allocated and -sized array.
This reduces the size of the adapter structure, and allows us to support
any number of queue vectors in the future without changing the code.
Change-ID: I08dc622cb2f2ad01e832e51c1ad9b86524730693
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If, upon a midnight dreary, the PF returns ERR_PARAM when the VF is
requesting resources, that's fatal. Either the firmware or NVM is badly,
badly misconfigured, or this VF has been disabled due to a previous VF
driver sending a bunch of bogus messages.
Either way, there is no recovery from this. Don't ponder weak and weary,
just quit.
Change-ID: I09d9f16cc4ee7fec3b57646a289d33838c1c5bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we get an invalid message from a VF, we should tell the user which VF
is being naughty, rather than making them guess.
Change-ID: I9252cef7baea3d8584043ed6ff12619a94e2f99c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the confusing kernel message of enabled RSS size,
by reporting it together with the hardware maximum RSS size.
Change-ID: I64864dbfbc13beccc180a7871680def1f3d5a339
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Change-ID: Ic5d3db8d9df52182b560248f8cdca9c5c7546879
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two ways to get RSS, this patch implements two functions
with the same input parameters, and creates a more generic function
for getting RSS configuration.
Change-ID: I12d3b712c21455d47dd0a5aae58fc9b7c680db59
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two ways to configure RSS, this patch adjusts those two
functions with the same input parameters, and creates a more
generic function for configuring RSS.
Change-ID: Iace73bdeba4831909979bef221011060ab327f71
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames old VF adapter specific RSS function to clarify
its scope.
Change-ID: Ie5253083a44c677ebb7709a8a3a18402ad2dc6a6
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Issue a prefetch for data early in the transmit path.
This should not be generally needed for Tx traffic, but
it helps immensely for pktgen workloads and should help
for forwarding workloads as well.
Change-ID: Iefee870c20599e0c4240e1d8637e4f16b625f83a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump amd when
it does a WB. It also optimizes when we do a wmb.
Change-ID: Id831e1ae7d3e2ec3f52cd0917b41ce1d22d75d9d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Change-ID: I73886469dca9e9f6b16d842182a87f3f4009f95d
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For GMAC newer than 3.40a there is a new register (Reg_9) that provides the
status of all modules of the transmit and receive paths and FIFO status.
These can be exposed via ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add support for 7000 series 40G NIC VF.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Solarflare 8000 series NIC will use a new TSO scheme. The current
driver refuses to load if the current TSO scheme is not found. Remove
that check and instead make the TSO version a per-queue parameter.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gianfar driver has recently been enabled on arm64 but fails to build
since it check the return value of platform_get_irq() against NO_IRQ. Fix
this by instead checking for a negative error code.
Even on ARM where this code was previously being built this check was
incorrect since platform_get_irq() returns a negative error code which
may not be exactly the (unsigned int)(-1) that NO_IRQ is defined to be.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can be built on arm64 but relies on NO_IRQ to check the return
value of irq_of_parse_and_map() which fails to build on arm64 because the
architecture does not provide a NO_IRQ. Fix this to correctly check the
return value of irq_of_parse_and_map().
Even on ARM systems where the driver was previously used the check was
broken since on ARM NO_IRQ is -1 but irq_of_parse_and_map() returns 0 on
error.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASIC provides access to fans. Implement their exposure to userspace
using hwmon.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition of MFCR, MFSC and MFSM which provide possibility to
control and monitor fans.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASIC provides access to temperature sensors. Implement their exposure to
userspace using hwmon.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition of MTCAP and MTMP registers which provide access to
temperature sensors.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to flash the port's LED in order to identify it. This is
achieved by setting the Management LED Control Register (MLCR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MLCR register, which controls physical port identification LEDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive skb buffers can be preallocated when the link is opened
according to mtu size.
While testing on a network environment with not standard MTU (e.g. 3000),
a panic occurred if an incoming packet had a length greater than rx skb
buffer size. This is because the HW is programmed to copy, from the DMA,
an Jumbo frame and the Sw must check if the allocated buffer is enough to
store the frame.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stmmac_mdio_reset, was called from stmmac_resume, it was not
resetting the PHY due to which MAC was not getting reset properly and
hence ethernet interface not was resumed properly.
The issue was currently only reproducible on stih301-b2204.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the st,tx-retime-src is missing from device-tree
(it's an optional field) the driver will invoke the strcasecmp to check
which clock has been selected and this is a bug; the else condition
is needed.
In the dwmac_setup, the "rs" variable, passed to the strcasecmp, was not
initialized and the compiler, depending on the options adopted, could
take it in some different part of the stack generating the hang in such
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the csr clock in case of 300MHz is provided.
Reported-by: Kent Borg <Kent.Borg@csr.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resume the HW is re-configured but some settings can be lost.
For example, the MAC Address_X High/Low Registers used for VLAN tagging..
So, while resuming, the set_filter callback needs to be invoked to
re-program perfect and hash-table registers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once TX has been enabled on a NIC, it is illegal to access skb,
as this skb might have been freed by another cpu, from TX completion
handler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the old pf-specific function in order to clarify
its scope. This patch also creates a more generic configure RSS
function with the old name.
This patch also creates a new more generic function to get RSS
configuration, using the appropriate method.
Change-ID: Ieddca2707b708ef19f1ebccdfd03a0a0cd63d3af
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust the RSS configure functions so that there is a generic way to
hook to ethtool hooks.
Change-ID: If446e34fcfaf1bc3320d9d319829a095b5976e67
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where using ethtool rxnfc command could
let RX flow hash be set on disabled queues. This patch fixes the
problem by returning the number of enabled queues before setting
rxnfc.
Change-ID: Idbac86b0b47ddacc8deee7cd257e41de01cbe5c0
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a lot (many hundreds) of MAC or VLAN filters are added at one time,
we can overflow the Admin Queue buffer size with all the requests.
Unfortunately, the driver would then calculate the message size
incorrectly, causing it to be rejected by the PF. Furthermore, there was
no mechanism to trigger another request to allow for configuring the
rest of the filters that didn't fit into the first request.
To fix this, recalculate the correct buffer size when we detect the
overflow condition instead of just assuming the max buffer size. Also,
don't clear the request bit in adapter->aq_required when we have an
overflow, so that the rest of the filters can be processed later.
Change-ID: Idd7cbbc5af31315e0dcb1b10e6a02ad9817ce65c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up and enhance error messages related to VF MAC/VLAN filters.
Indicate which VF is having issues, and if possible indicate the MAC
address or VLAN involved.
Also, when an error is returned from the PF driver, print useful
information about what went wrong, for the most likely cases.
Change-ID: Ib3d15eef9e3369a78fd142948671e5fa26d921b8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a comment to the #endif to more easily match it with its #if.
Change-ID: I47eb0a60a17dc6d2f01a930e45006d2dc82e044f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The watchdog only calls link_event not handle_link_event which means
that we need to save the old information in link_event.
Previously when polling we were comparing current data to the old data
saved the last time we actually received a link event. This means that
the polling would only fix link status changes in one direction
depending on what the last old data saved off was.
Change-ID: Ie590f30fdbcb133d0ddad4e07e3eb1aad58255b3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the kernel thread here. If this condition was
true, the probe() would have died long before we got here. In any case,
we'll get the same result when this code tries to use the VSI pointer
being checked.
Prompted by a recent Linus diatribe.
Change-ID: I62f531cac34d4fc28ff9657d5b2d9523ae5e33a4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's really no reason to kill the kernel thread just because of a
little info string. This reworks the code to use snprintf's limiting to
assure that the string is never too long, and WARN_ON to still put out
a warning that we might want to look at the feature list length.
Prompted by a recent Linus diatribe.
Change-ID: If52ba5ca1c2344d8bf454a31bbb805eb5d2c5802
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the thread and eventually the kernel in this
case. In fact, the remainder of the code won't hurt anything anyway,
so just complain that we're here and move along.
Prompted by a recent Linus diatribe.
Change-ID: Iec020d8bcfedffc1cd2553cc6905fd915bb3e670
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was moved into a separate function some time ago.
Change-ID: Icabbe71ce05cf5d716d3e1152cdd9cd41d11bcb5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k_msix_clean_rings function runs from hard interrupt context or
with interrupts already disabled in netpoll.
It can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), R-Car Gen1 SoCs are only supported in generic
DT-only ARM multi-platform builds. The driver doesn't need to match
platform devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect sh_eth_set_rate_r8a777x() and r8a777x_data by #ifdef CONFIG_OF,
as they're now referenced on DT platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1fa59bda21 ("ARM: shmobile: Remove legacy board code
for Armadillo-800 EVA"), r8a7740 is only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r8a7740_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only. Move it to a more logical position, in front of the
r8a777x support, so we can have a single #ifdef covering all r7s* and
r8a* support soon. This requires moving a few helper functions, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r8a779x_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 05104c266a ("ARM: shmobile: r7s72100: genmai: Remove
legacy board file"), r7s72100 is only supported in generic DT-only ARM
multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Protect r7s72100_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only. Move it to a more logical position, in front of the
r8a777x support, so we can have a single #ifdef covering all r7s* and
r8a* support soon. This requires moving a helper function, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
in case of error no need to set num_tx and num_rx = 1, because in case of error
these variables will remain unchanged by of_property_read_u32 ie 1 only
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch does the following:
1 . remove unnecessary if, else condition
2 . reduce one variable
3 . change the return type of 2 functions to void as there return values
turn out to be 0 always after above changes
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is pretty confused. The variable name 'bytes_not_copied'
clearly indicates that the programmer knew the semantics of
copy_{to,from}_user, but then the return value is checked for being
negative and used as a -Exxx return value.
I'm not sure this is the proper fix, but at least we get rid of the
dead code which pretended to check for access faults.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbevf is loaded while the corresponding PF interface is down
and the driver assigns a random MAC address, that address can be
overwritten with the value of hw->mac.perm_addr, which would be 0 at
that point.
To avoid this case we init hw->mac.perm_addr to the randomly generated
address and do not set it unless we receive ACK from ixgbe.
Reported-by: John Greene <jogreene@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
replace some instances of memcpy for setting up the mac address with
ether_addr_copy()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiler complained of an unused variable, which the driver was just
using to store the result of a rd32 which is used to clear a register
unconditionally. Just drop the unused variable and re-use one.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Testing has now shown that the diagnostic code used with the CS4227
is no longer needed, so remove it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_intr and ixgbe/ixgbevf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is the ixgbevf version of commit 8ac34f10a5 "ixgbe: Limit
lowest interrupt rate for adaptive interrupt moderation to 12K"
The same logic applies here as well as the same results since a netperf
test will starve for memory in the time from one Tx interrupt to the next.
As a result the ixgbevf driver underperformed when compared to vhost_net.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
KR auto-neg mode is what we will be using going forward. The SW
interface for this mode is different that what was used for iXFI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit dfaf891dd3 ("ixgbe: Refactor the RSS configuration code")
introduced a few kernel-doc errors:
1) The function name is missing;
2) The format is wrong;
3) The short description is redundant.
Fix all the above for the correct execution of the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete a redundant include of net/vxlan.h.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on hardware testing, the host interface supports up to 15368 bytes
as the maximum frame size. To determine the correct MTU, we subtract 8
for the internal switch tag, 14 for the L2 header, and 4 for the
appended FCS header, resulting in 15342 bytes of payload for our maximum
MTU on jumbo frames.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible that the PF has not yet assigned resources to the VF.
Although rare, this could result in the VF attempting to read queues it
does not own and result in FUM or THI faults in the PF. To prevent this,
check queue 0 before we continue in init_hw_vf.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Freescale hosts some ARMv8 based SoCs, and a generic convention
ARCH_LAYERSCAPE is used to cover such SoCs. Adding ARCH_LAYERSCAPE
to dependencies of NET_VENDOR_FREESCALE to support networking on those
SoCs.
The ARCH_LAYERSCAPE is introduced by:
commit: 53a5fde05 arm64: Use generic Layerscape SoC family naming
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use of_property_read_bool() for testing bool property
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46e8a249423ff "bnx2x: Add FW 7.13.1.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.
This introduces 2 fixes/enhancements:
- In some management protocols there are outer-vlan configurations
that can be dynamically changed while device is running. This fixes
some corner cases where such a change did not take effect.
- Prevent VFs from sending MAC control frames; FW would treat a VF
sending such a packet as malicious and block any further communication
done by the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_dma_mask returns a negative errno value, not a bool like
pci_dma_supported. This of course was just a giant test for attention :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jongman Heo <jongman.heo@samsung.com>
Tested-by: Jongman Heo <jongman.heo@samsung.com> [pcnet32]
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GTI.TIV may be set to 2GHz^2 / rate, where rate is
that of the clock of the device. Rather than assuming a
rate of 130MHz use the actual rate of the clock.
The motivation for this is to use the correct rate on
the r8a7795/Salvator-X which is advertised as 133MHz but
may differ depending on the extal present on the Salvator-X.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend/resume support to dl2k driver.
This requires RX/TX rings to be reset so split out the required
functionality from alloc_list() into new rio_reset_ring().
Tested on Asus NX1101 (IP1000A) and D-Link DGE-550T (DL-2000).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move HW init and stop into separate functions.
Request IRQ only after the HW has been reset (so interrupts are
disabled and no stale interrupts are pending).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If memory allocation fails in alloc_list(), free the already allocated
memory and return -ENOMEM. In rio_open(), call alloc_list() first and
abort if it fails. Move HW access (set RFDListPtr) out ot alloc_list().
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, port statistics are being presented when using `ethool -S' only
for single-function devices, but there are some port statistics which are
crucial for analyzing bottle-necks. E.g., HW Rx discards due to lack of
buffer space [when device isn't handling ingress traffic fast enough].
Judging the pros and cons, it was decided that in-order to better support
automatic dump-gathering tools, bnx2x should no longer hide those stats.
This leaves only VFs lacking the port statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver already has an internal counter for number of times a given queue
had to be stopped due to Tx ring exhaustion.
This add the counter to the statistics presented by driver, e.g., by using
`ethtool -S'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operation of adding VLANs on a port via switchdev ops can fail and
we need to be prepared for it. If we do not rollback hardware operations
following a failure, hardware and software will remain in an
inconsistent state.
Solve that by adding suitable error paths to __mlxsw_sp_port_vlans_add.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding or deleting VLANs from a bridged port, HW VLAN filters must be
set accordingly. Instead of having the same code in both add and delete
functions, just wrap it in a function and call it with the appropriate
parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a range of VLANs in which PVID is a member we should use
the correct PVID value instead of some VLAN in the range.
Also, change two print statements to use 'dev' instead of
'mlxsw_sp_port->dev', as it's already used in other print statements in
the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tulip driver causes annoying build-time warnings for allmodconfig
builds for all recent architectures:
dec/tulip/winbond-840.c:910:2: warning: #warning Processor architecture undefined
dec/tulip/tulip_core.c:101:2: warning: #warning Processor architecture undefined!
This is the last remaining warning for arm64, and I'd like to get rid of
it. We don't really know the cache line size, architecturally it would
be at least 16 bytes, but all implementations I found have 64 or 128
bytes. Configuring tulip for 32-byte lines as we do on ARM32 seems to
be the safe but slow default, and nobody who cares about performance these
days would use a tulip chip anyway, so we can just use that.
To save the next person the job of trying to find out what this is for
and picking a default for their architecture just to kill off the warning,
I'm now removing the preprocessor #warning and turning it into a pr_warn
or dev_warn that prints the equivalent information when the driver gets
loaded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commmit ac7eccd4d4 "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6745f6e4e ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.
Let's fix the issue by adding handling for dm814x.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthnan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When encx24j600 is open and closed many times due to userspace polling the
interface, the log gets noise with this log message.
Moving this to encx24j600_spi_probe function where it belongs.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the R8A7795 support was added to the driver, little attention was paid
to the ravb_open() error path: free_irq() for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device opening error:
WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1448 __free_irq+0x8c/0x228()
Trying to free already-free IRQ 0
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc1-dirty #1005
Hardware name: Generic R8A7791 (Flattened Device Tree)
Backtrace:
[<c0013818>] (dump_backtrace) from [<c00139b4>] (show_stack+0x18/0x1c)
r6:c063cdd6 r5:00000009 r4:00000000 r3:00204140
[<c001399c>] (show_stack) from [<c022a578>] (dump_stack+0x74/0x90)
[<c022a504>] (dump_stack) from [<c0025f04>] (warn_slowpath_common+0x8c/0xb8)
r4:ef04fd38 r3:c0714770
[<c0025e78>] (warn_slowpath_common) from [<c0025fd4>] (warn_slowpath_fmt+0x38/0x40)
r8:ee8ad800 r7:ef0030a0 r6:00000000 r5:00000000 r4:ef003040
[<c0025fa0>] (warn_slowpath_fmt) from [<c0064cc0>] (__free_irq+0x8c/0x228)
r3:00000000 r2:c063ce9f
[<c0064c34>] (__free_irq) from [<c0064ecc>] (free_irq+0x70/0xa4)
r10:0000016b r8:00000000 r7:00000000 r6:ee8ad800 r5:00000000 r4:ef003040
[<c0064e5c>] (free_irq) from [<c033472c>] (ravb_open+0x224/0x274)
r7:fffffffe r6:00000000 r5:fffffffe r4:ee8ad800
[<c0334508>] (ravb_open) from [<c041ac78>] (__dev_open+0x84/0x104)
r7:ee8ad830 r6:c0566334 r5:00000000 r4:ee8ad800
[<c041abf4>] (__dev_open) from [<c041af08>] (__dev_change_flags+0x94/0x13c)
r7:00001002 r6:00000001 r5:00001003 r4:ee8ad800
[<c041ae74>] (__dev_change_flags) from [<c041afe8>] (dev_change_flags+0x20/0x50)
r7:c072e6e0 r6:00000138 r5:00001002 r4:ee8ad800
[<c041afc8>] (dev_change_flags) from [<c06ec06c>] (ip_auto_config+0x174/0xfb8)
r8:00001002 r7:c072e6e0 r6:c0703344 r5:00000001 r4:ee8ad800 r3:00000101
[<c06ebef8>] (ip_auto_config) from [<c000a810>] (do_one_initcall+0x100/0x1cc)
r10:c06fb83c r9:00000000 r8:c06ebef8 r7:c0736000 r6:c0710918 r5:c0710918
r4:ef2f8f80
[<c000a710>] (do_one_initcall) from [<c06ccddc>] (kernel_init_freeable+0x11c/0x1
ec)
r10:c06fb83c r9:00000000 r8:0000009a r7:c0736000 r6:c0706bf0 r5:c06fb834
r4:00000007
[<c06cccc0>] (kernel_init_freeable) from [<c0514c54>] (kernel_init+0x14/0xec)
r10:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0514c40 r4:c0736000
[<c0514c40>] (kernel_init) from [<c0010458>] (ret_from_fork+0x14/0x3c)
r4:00000000 r3:ef04e000
Fix up the free_irq() call order and add a new label on the error path.
Fixes: 22d4df8ff3 ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Busy polling can now be handled in generic NAPI poll infrastructure.
This removes complexity and fast path overhead :
mlx4 used two spin_lock()/spin_unlock() pair per napi->poll() call
in mlx4_en_cq_lock_napi()/mlx4_en_cq_unlock_napi()
Tested:
Without busy polling :
lpaa23:~# echo 0 >/proc/sys/net/core/busy_read
lpaa24:~# echo 0 >/proc/sys/net/core/busy_read
lpaa23:~# ./netperf -H lpaa24 -t TCP_RR
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpaa24.prod.google.com () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 47330.78
With busy polling :
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# ./netperf -H lpaa24 -t TCP_RR
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpaa24.prod.google.com () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 97643.55
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NAPI poll handler should return number of RX packets processed,
instead of 0 / budget.
This allows proper busy poll accounting through LINUX_MIB_BUSYPOLLRXPACKETS
SNMP counter.
napi_complete_done() allows /sys/class/net/ethX/gro_flush_timeout
to be used for finer GRO aggregation control.
Tested:
Enabled busy polling, and checked TcpExtBusyPollRxPackets counter is increasing.
echo 70 >/proc/sys/net/core/busy_read
nstat >/dev/null
netperf -H target -t TCP_RR >/dev/null
nstat | grep TcpExtBusyPollRxPackets
TcpExtBusyPollRxPackets 490958 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is now easy to add busy polling support to a NAPI driver,
with very little impact on normal input path.
This patch serves as a reference implementation.
Note:
A followup patch will add proper napi_complete_done() in mlx5,
so that LINUX_MIB_BUSYPOLLRXPACKETS snmp counter is properly handled.
Tested:
Normal TCP_RR results without busy polling :
lpk51:~# echo 0 >/proc/sys/net/core/busy_read
lpk52:~# echo 0 >/proc/sys/net/core/busy_read
lpk51:~# ./netperf -H 192.168.4.52 -t TCP_RR -l 10
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.4.52 () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 53509.49
16384 87380
Now enable busy polling :
lpk51:~# echo 70 >/proc/sys/net/core/busy_read
lpk52:~# echo 70 >/proc/sys/net/core/busy_read
lpk51:~# ./netperf -H 192.168.4.52 -t TCP_RR -l 10
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.4.52 () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 97530.92
16384 87380
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_low_latency_recv() is called with BH disabled,
as other ndo_busy_poll() methods.
No need for spin_lock_bh()/spin_unlock_bh()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lancer_cmd_get_file_len() uses lancer_cmd_read_object() to get
the current size of registers for ethtool registers dump. Returned status
value is stored but not checked. The check itself is not necessary as
the data_read output variable is initialized to 0 and status variable
can be removed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI device ID (0xe0a1) and alx_pci_tbl entry for the
Killer E2400 Ethernet controller, modeled after the Killer E2200
controller support (0xe091) already present in the alx driver.
This patch was originally authored by Ben Pope, but it got held up by
issues in the commit message, so I'm resubmitting it on his behalf.
I've extensively used a kernel with this patch on a System76 serw9
laptop and am quite confident it works well (at least on the hardware I
have available for testing).
Note that as a favor to System76, Ubuntu has been carrying this as a
sauce patch in their 4.2 based Wily kernel, which presumably has given
it real-world testing on other E2400 equipped hardware (I don't know of
any Ubuntu kernel bugs filed about it):
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1498633
Signed-off-by: Jason Gerard DeRose <jason@system76.com>
Signed-off-by: Ben Pope <benpope81@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was detected by Coverity.
The function skb_cow_head leaves skb alone on failure, so caller needs
to free.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable wasn't set with the correct error value in some cases.
Fixes: 47605df953 ('mlx4: Modify proxy/tunnel QP mechanism [..]')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96a ("net/mlx4_core: Reset counters data when freed")
Reported-by: Moni Shoua <monis@mellanox.com>
Tested-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On xmit path we use skb_frag_dma_map() which is using dma_map_page(),
while upon completion we dma-unmap the skb fragments using
dma_unmap_single() rather than dma_unmap_page().
To fix this, we now save the dma map type on xmit path and use this
info to call the right dma unmap method upon TX completion.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller