All the upper level protocols like rdma, iscsi have their own offload rx
queues, so instead of using the generic naming convention be specific
while naming them. Improves code readability
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the device get enough bandwidth from the entire PCI chain to
satisfy its capabilities. This patch determines the PCIe device's
bandwidth capabilities by reading its PCIe Link Capabilities registers
and then call the pcie_get_minimum_link function to ensure that the
adapter is hooked into a slot which is capable of providing the
necessary bandwidth capabilities.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
KASan reported use-after-free for the hwmon structure. So fix this by
using devm_kzalloc and let the core take care about freeing the memory
during device dettach.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another sysfs hwmon attribute to expose possibility to reset
temperature sensors history.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1299653aff ("sh_eth: fix descriptor access endianness") only
addressed the 32-bit buffer address field byte-swapping but the driver
still accesses 16-bit frame/buffer length descriptor fields without the
necessary byte-swapping -- which should affect the big-endian kernels.
In order to be able to use {cpu|edmac}_to_{edmac|cpu}(), we need to declare
the RX/TX descriptor word 1 as a 32-bit field and use shifts/masking to
access the 16-bit subfields (which gets rid of the ugly #ifdef'ery too)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tri-states need 'if IS_ENABLED()', booleans should use 'ifdef'.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup a number of issues with function header comments, lower-case
acronyms (i.e. FIFO, TLV), duplicate comments and a stubbed-out header
comment for fm10k_sm_mbx_init.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These structures never change so declare them as const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When comparing MAC addresses, use ether_addr_equal instead of memcmp to
ETH_ALEN length. Found and replaced using the following sed:
sed -e 's/memcmp\x28\(.*\), ETH_ALEN\x29/!ether_addr_equal\x28\1\x29/'
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to cleanup the exception handling for the paths where
we reset the interrupts and then reconfigure them. In all of these paths
we had very different levels of exception handling. I have updated the
driver so that all of the paths should result in a similar state if we
fail.
Specifically the driver will now unload the mailbox interrupt, free the
queue vectors and MSI-X, and then detach the interface.
In addition for any of the PCIe related resets I have added a check with
the hw_ready function to just make sure the registers are in a readable
state prior to reopening the interface.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TLV format for little endian structures is actually 4 byte aligned
copy. To this end, we need to add an additional __aligned(4) marker
along with __packed to ensure that these structures are actually 4 byte
aligned and packed correctly. Use of just __packed will not work as this
will result in 1byte alignment which is incorrect. Add a comment
explaining the reasoning behind why these structures need the special
treatment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleans up checkpatch GLOBAL_INITIALIZERS error
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kcalloc in this case as it is allocating an array
of elements.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refill_rx() and start_tx() do not check if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
A cleanup patch I did was unfortunately wrong and introduced
multiple serious bugs in the netcp rx processing, as indicated
by these correct gcc warnings:
drivers/net/ethernet/ti/netcp_core.c:776:14: warning: 'buf_ptr' may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/ti/netcp_core.c:687:14: warning: 'ptr' may be used uninitialized in this function [-Wuninitialized]
I have checked the patch once more and found that a call to
get_pkt_info() accidentally got removed in netcp_free_rx_desc_chain,
and netcp_process_one_rx_packet no longer retrieved the correct
buffer length. This patch should fix all the known problems,
but I did not test on real hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8990777914 ("netcp: try to reduce type confusion in descriptors")
Signed-off-by: David S. Miller <davem@davemloft.net>
FW has a rare corner case in which a fragmented packet using lots
of frags would not be linearized, causing the FW to assert while trying
to transmit the packet.
To prevent this, we need to make sure the window of fragements containing
MSS worth of data contains 1 BD less than for regular packets due to
the additional parsing BD.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first request_irq fails in be_msix_register, i value
would be zero. The current code decrements the i value and
accesses the eq object without validating the decremented
"i" value. This can cause an "invalid memory address access"
violation.
This patch fixes the problem by accessing the eq object after
validating the "i" value.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevs default to carrier on, we should call netif_carrier_off()
during initialization since we handle carrier state changes in the
driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_init_timestamp was called before creation of netdev and port
init, thus used uninitialized values. Specifically - NIC frequency was
incorrect causing wrong calculations and later wrong HW timestamps.
Fixes: 1ec4864b10 ('net/mlx4_en: Fixed crash when port type is changed')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service task is responsible for other tasks in addition to timestamping
overflow check. Launch it even if timestamping is not supported by device.
Fixes: 07841f9d94 ('net/mlx4_en: Schedule napi when RX buffers allocation fails')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a fixed-link sub-node exists in a slave node, the slave node
is also the PHY node. Since this is a separate use of the slave node,
of_node_get() should be used to increment the reference count.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1f71e8c96f ("drivers: net: cpsw: Add
support for fixed-link PHY") did not parse the "phy-mode" property in
the case of a fixed-link PHY, leaving slave_data->phy_if with its default
of PHY_INTERFACE_MODE_NA(0). This later gets passed to phy_connect() in
cpsw_slave_open(), and eventually to cpsw_phy_sel() where it hits a default
case that configures the MAC for MII mode.
The user visible symptom is that while kernel log messages seem to indicate
that the interface is set up, there is no network communication. Eventually
a watchdog error occurs:
NETDEV WATCHDOG: eth0 (cpsw): transmit queue 0 timed out
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using more than one slave with ti cpsw and fixed phy the pd->phy_id
will be always zero, but slave_data->phy_id must be unique. pd->phy_id
means a "phy hardware id" whereas slave_data->phy_id means an "unique id",
so we should use pd->addr which has the same unique meaning.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: Pascal Speck <kernel@iktek.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix uninitialized variable warnings in nfnetlink_queue, a lot of
people reported this... From Arnd Bergmann.
2) Don't init mutex twice in i40e driver, from Jesse Brandeburg.
3) Fix spurious EBUSY in rhashtable, from Herbert Xu.
4) Missing DMA unmaps in mvpp2 driver, from Marcin Wojtas.
5) Fix race with work structure access in pppoe driver causing
corruptions, from Guillaume Nault.
6) Fix OOPS due to sh_eth_rx() not checking whether netdev_alloc_skb()
actually succeeded or not, from Sergei Shtylyov.
7) Don't lose flags when settifn IFA_F_OPTIMISTIC in ipv6 code, from
Bjørn Mork.
8) VXLAN_HD_RCO defined incorrectly, fix from Jiri Benc.
9) Fix clock source used for cookies in SCTP, from Marcelo Ricardo
Leitner.
10) aurora driver needs HAS_DMA dependency, from Geert Uytterhoeven.
11) ndo_fill_metadata_dst op of vxlan has to handle ipv6 tunneling
properly as well, from Jiri Benc.
12) Handle request sockets properly in xfrm layer, from Eric Dumazet.
13) Double stats update in ipv6 geneve transmit path, fix from Pravin B
Shelar.
14) sk->sk_policy[] needs RCU protection, and as a result
xfrm_policy_destroy() needs to free policies using an RCU grace
period, from Eric Dumazet.
15) SCTP needs to clone ipv6 tx options in order to avoid use after
free, from Eric Dumazet.
16) Missing kbuild export if ila.h, from Stephen Hemminger.
17) Missing mdiobus_alloc() return value checking in mdio-mux.c, from
Tobias Klauser.
18) Validate protocol value range in ->create() methods, from Hannes
Frederic Sowa.
19) Fix early socket demux races that result in illegal dst reuse, from
Eric Dumazet.
20) Validate socket address length in pptp code, from WANG Cong.
21) skb_reorder_vlan_header() uses incorrect offset and can corrupt
packets, from Vlad Yasevich.
22) Fix memory leaks in nl80211 registry code, from Ola Olsson.
23) Timeout loop count handing fixes in mISDN, xgbe, qlge, sfc, and
qlcnic. From Dan Carpenter.
24) msg.msg_iocb needs to be cleared in recvfrom() otherwise, for
example, AF_ALG will interpret it as an async call. From Tadeusz
Struk.
25) inetpeer_set_addr_v4 forgets to initialize the 'vif' field, from
Eric Dumazet.
26) rhashtable enforces the minimum table size not early enough,
breaking how we calculate the per-cpu lock allocations. From
Herbert Xu.
27) Fix FCC port lockup in 82xx driver, from Martin Roth.
28) FOU sockets need to be freed using RCU, from Hannes Frederic Sowa.
29) Fix out-of-bounds access in __skb_complete_tx_timestamp() and
sock_setsockopt() wrt. timestamp handling. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (117 commits)
net: check both type and procotol for tcp sockets
drivers: net: xgene: fix Tx flow control
tcp: restore fastopen with no data in SYN packet
af_unix: Revert 'lock_interruptible' in stream receive code
fou: clean up socket with kfree_rcu
82xx: FCC: Fixing a bug causing to FCC port lock-up
gianfar: Don't enable RX Filer if not supported
net: fix warnings in 'make htmldocs' by moving macro definition out of field declaration
rhashtable: Fix walker list corruption
rhashtable: Enforce minimum size on initial hash table
inet: tcp: fix inetpeer_set_addr_v4()
ipv6: automatically enable stable privacy mode if stable_secret set
net: fix uninitialized variable issue
bluetooth: Validate socket address length in sco_sock_bind().
net_sched: make qdisc_tree_decrease_qlen() work for non mq
ser_gigaset: remove unnecessary kfree() calls from release method
ser_gigaset: fix deallocation of platform device structure
ser_gigaset: turn nonsense checks into WARN_ON
ser_gigaset: fix up NULL checks
qlcnic: fix a timeout loop
...
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Michael Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Michael Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Tx flow control is based on reading the hardware state,
which is not accurate since it may not reflect the descriptors that
are not yet reached the memory.
To accurately control the Tx flow, changing it to be software based.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to clear delayed kick counters when we free rings otherwise
after ndo_close()/ndo_open() we could kick HW by more entries than
actually written to rings.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Rolf Neugebauer <rolf.neugebauer@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes FCC port lock-up, which occurs as a result of a bug
during underrun/collision handling. Within the tx_startup() function
in mac-fcc.c, the address of last BD is not calculated correctly.
As a result of wrong calculation of the last BD address, the next
transmitted BD may be set to an area out of the transmit BD ring.
This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.
We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to geneve_get_rx_port in i40e so that when it
comes up it can learn about the existing geneve tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Kconfig file with dependency for supporting GENEVE tunnel
offloads.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides an options to use the ptp clock routed from the Altera FPGA
fabric. Instead of the defalt eosc1 clock connected to the ARM HPS core.
This setting affects all emacs in the core as the ptp clock is common.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_config_sub_second_increment set the sub second increment to 20ns.
Driver is configured to use the fine adjustment method where the sub second
register is incremented when the acculumator incremented by the addend
register wraps overflows. This accumulator is update on every ptp clk
cycle. If a ptp clk with a period of greater than 20ns was used the
sub second register would not get updated correctly.
Instead set the sub sec increment to twice the period of the ptp clk.
This result in the addend register being set mid range and overflow
the accumlator every 2 clock cycles.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA driver needs to be passed a reference to an mdio bus. Typically
the mac is configured to use a fixed link but the mdio bus still needs
to be registered so that it con configure the switch.
This patch follows the same process as the altera tse ethernet driver for
creation of the mdio bus.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.
This patch also:
- Cleans up can_checksum_protocol
- Simplifies netdev_intersect_features
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that at the end of the loop we test for if
idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a
post-op, it actually ends up set to (u8)-1. I have fixed this by
moving the decrement inside the loop.
Fixes: 486a5bc77a ('qlcnic: Add support for 83xx suspend and resume.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for if "tries" is zero at the end but "tries--" is a post-op so
it will end with "tries" set to -1. I have changed it to a pre-op
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that after the loop we test for "if (!i) " but
because "i--" is a post-op we exit with i set to -1. I have fixed this
by changing it to a pre-op instead. I had to change the starting value
from 3 to 4 so that we still iterate 3 times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of the fixed PHY.
This patch is based on commit 87009814cd ("ucc_geth: use the new fixed
PHY helpers").
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the loop we test "if (!count)" but because "count--" is
a post-op then the loop will end with count set to -1. I have fixed
this by changing it to --count.
Fixes: c5aa9e3b81 ('amd-xgbe: Initial AMD 10GbE platform driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a VLAN device on top of LAG, we are basically creating a
vPort on top of each of the port netdevs member in the LAG. Therefore,
these vPorts should inherit both the LAG status and LAG ID from the
underlying port netdevs.
In addition, when the VLAN device joins or leaves a bridge each of the
underlying vPorts should know about it and act accordingly. This is
achieved by propagating the VLAN event down to the lower devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding or removing FDB records of VLAN devices on top of LAG we
should set the lag_vid parameter to the VLAN ID of the VLAN device. It
is reserved otherwise.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unicast LAG records in the Switch Filtering Database (SFD) register have
a lag_vid field indicating the VLAN ID in case of vFIDs. This field is
no longer reserved since we are going to add support for VLAN devices on
top of LAG.
Add the lag_vid field to be used by VLAN devies on top of LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the member VLAN devices in a bridge need to share the same vFID.
To achieve that, expand the vFID struct to include the associated bridge
device (or lack of) and allow one to lookup a vFID based on a bridge
device.
When joining a bridge, lookup the relevant vFID or create one if none
exists. Next, make the VLAN device use the vFID.
Leaving a bridge can either occur because a user removed the VLAN device
from a bridge or because the VLAN device was deleted by the user. In the
latter case the bridge's teardown sequence is invoked after the hardware
vPort is already gone. Therefore, when unlinking the VLAN device from
the real device, check if the associated vPort is bridged and act
accordingly. The bridge's notification will be ignored in this case.
Note that bridging a VLAN interface with an ordinary port netdev is
currently not supported, but not forbidden. This will be addressed in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface is configured on top of a physical port we should
associate the VLAN device with the matching vPort. Likewise, when it's
removed, we should revert back to the underlying port netdev.
While not a must, this is consistent with port netdevs and also provides
a more accurate error printing via netdev_err() and friends.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications contain the FID and port (or LAG ID) on which the MAC
was learned. In the case of the 802.1Q bridge one can easily derive the
matching VID - as FID equals VID - and generate the appropriate
notification for the software bridge. With VLAN devices this is no
longer the case, as these are associated with a vFID.
Solve that by converting the FID to a vFID and lookup the matching VLAN
device. From that derive the VID and whether learning (and learning
sync) should occur.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev ops can now be called for VLAN devices and we need to be
prepared for it. Until now they were only called for the port netdev.
Use the newly propagated orig_dev passed as part of the switchdev
attr/obj and determine whether the original device is a VLAN device. If
so, act accordingly, otherwise continue as usual.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Spectrum ASIC - unlike SwitchX-2 - FDB access is done by
specifying FID as parameter and not VID.
Change the relevant variables and parameters names to reflect that.
Note that this was OK up until now, since FID was always equal to VID,
but with the introduction of VLAN interfaces this is no longer the case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously used only one flood table for packets classified to vFIDs.
However, since we are going to add support for bridges between VLAN
interfaces (mapped to vFIDs) we need to add one more flood table.
That way we can separate the flooding domain of unknown unicast traffic
from all the rest and support flood control (as we do with the 802.1Q
bridge).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __mlxsw_sp_port_flood_set function is now used to configure flooding
for both FIDs and vFIDs, so change the parameter name to 'idx' instead
of 'fid'. This is also consistent with hardware documentation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used a 1:1 mapping - based on VID - to map a VLAN
interface to a vFID. However, a different scheme is needed in order to
support bridges between VLAN interfaces, as all the member interfaces -
which can have different VIDs - need to share the same vFID.
Solve that by splitting the vFID range in two:
1. Non-bridged VLAN interfaces
2. Bridged VLAN interfaces
When a VLAN interface is created, assign it the next available vFID in
the first range, unless one already exists for that VID or number of
vFIDs in the range was exceeded. When interface is removed, free the
vFID, unless other interfaces are mapped to it.
To accomplish the above:
1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which
has a global context and holds a reference count.
2. Create a vPort (dummy in case of bridge SELF invocation) on top of
of the physical port and hold a reference to the associated vFID.
vfid vfid
+-------------+ +-------------+
| vfid | | vfid |
| vid +---> ... | vid |
| nr_vports | | nr_vports |
+------+------+ +------+------+
|
+-----------------------+-------+
| |
vport vport
+-------------+ +-------------+
| ... | | ... |
| *vfid +---> ... | *vfid +---> ...
| ... | | ... |
+------+------+ +------+------+
| |
port port
+-------------+ +-------------+
| ... | | ... |
| vports_list | | vports_list |
| ... | | ... |
+-------------+ +-------------+
swXpY swXpZ
Next patches in the series will add the missing infrastructure for the
second range and transfer vPorts between the two ranges according to the
received notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for bridges between VLAN interfaces, we'll introduce
a new entity called a vPort, which is a represntation of the VLAN
interface in the hardware.
The main difference between a vPort and a physical port is that several
FIDs can be bound to the latter, whereas only one (called a vFID) can be
bound to the first.
Therefore, it makes sense to use the same struct to represent the two,
but to only allocate the 'active_vlans' bitmap in case of a physical
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Fixes: fc48866f7 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2015-12-14
This series contains updates to e1000e and igb.
Alex Duyck changes e1000_up() to void since it always returned 0, also
by making it void, we can drop some code since we no longer have to worry
about non-zero return values.
Aaron Sierra removes GS40G specific defines and functions since the i210
internal PHY can be accessed with the access functions shared by 82580,
i350 and i354 devices. Also removes the code to add the PHY address into
the PCDL register address, since there is no real reason to do so.
Joe updates the cable length function reports all four pairs true min, max
and average cable length for i210. Also updated ethtool to use enum-based
labels instead of hard coded values.
Benjamin Poirier cleans up code that is never reachable since MSI-X
interrupts are not shared in e1000e. Also removes the ICR read in the
other interrupt handler, since the information is not needed and IMS is
configured such that the only link status change can trigger the other
interrupt handler. Fixed in MSI-X mode, there is no handler for the LSC
interrupt so there is no point in writing that to ICS now that we always
assume other interrupts are caused by LSC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB does not support 10 Mbps transfer speed.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver never calls cpu_to_edmac() when writing the descriptor address
and edmac_to_cpu() when reading it, although it should -- fix this.
Note that the frame/buffer length descriptor field accesses also need fixing
but since they are both 16-bit we can't use {cpu|edmac}_to_{edmac|cpu}()...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the little-endian SH771x kernels the driver has to byte-swap the RX/TX
buffers, however yet unset physcial address from the TX descriptor is used
to call sh_eth_soft_swap(). Use 'skb->data' instead...
Fixes: 31fcb99d99 ("net: sh_eth: remove __flush_purge_region")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).
While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.
This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.
Reported-by: Frank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.
Reviewed-by: Jasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.
The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the ethtool self-test gstrings/data arrays were accessed via
hardcoded indices, which made the code difficult to follow. This patch
replaces the hardcoded values with enum-based labels.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the PHY-specific code to get the cable length for the
I210 internal and related PHYs was reporting the cable length of a
single pair and reporting it as the min, max, and total cable length.
Update it so that all four pairs are checked so the true min, max,
and average cable lengths are reported.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to add the PHY address into the PCDL register address.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 3365711df0 ("sh_eth: WARN on access to a register not implemented in
in a particular chip") added WARN_ON() to sh_eth_{read|write}(), thus making
it unacceptable for these functions to be *inline* anymore. Remove *inline*
and move the functions from the header to the driver itself. Below is our
code economy with ARM gcc 4.7.3:
$ size drivers/net/ethernet/renesas/sh_eth.o{~,}
text data bss dec hex filename
32489 1140 0 33629 835d drivers/net/ethernet/renesas/sh_eth.o~
25413 1140 0 26553 67b9 drivers/net/ethernet/renesas/sh_eth.o
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmac-sunxi has 2 callbacks that were called from stmmac_platform as
part of the probe and remove sequences.
Ater the conversion of dwmac-sunxi into a standalone platform driver,
the .init function is called before calling into the stmmac driver
core, but .exit is not called to clean up if stmmac returns an error.
This patch fixes the probe error path. This properly cleans up and
releases resources when the driver core fails to probe.
Cc: Joachim Eastwood <manabian@gmail.com>
Fixes: 9a9e9a1ede ("stmmac: dwmac-sunxi: turn setup callback into a
probe function")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
AVB-DMAC Receive FIFO Warning interrupt is not enabled, so it is not
necessary to disable the interrupt in ravb_close().
On the other hand, this patch disables the interrupt in ravb_dmac_init() to
prevent the possibility that the interrupt is issued by the state that
a boot loader left.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The I210 internal PHY can be accessed just as well with the access
functions shared by 82580, I350, and I354 devices. A side effect of
relying on the common functions, is that I210 cable length support
is folded back into the common case which effectively reverts the
following commit:
commit 59f301046b
Author: Carolyn Wyborny <carolyn.wyborny@intel.com>
Date: Wed Oct 10 04:42:59 2012 +0000
igb: Update get cable length function for i210/i211
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function e1000e_up always returns 0. As such we can convert it to a
void and just ignore the results. This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some eisa_driver structures used __init probe functions which generates
a warning and could crash if function is called after being deleted.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
printf() has a dedicated specifier to print MAC addresses. Use it instead of
pushing each byte via stack.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark address pointer with __iomem in the IO accessors.
Otherwise we will get a sparse complain like following
.../hns/hns_dsaf_reg.h:991:36: warning: incorrect type in argument 1 (different address spaces)
.../hns/hns_dsaf_reg.h:991:36: expected unsigned char [noderef] [usertype] <asn:2>*base
.../hns/hns_dsaf_reg.h:991:36: got void *base
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ixgbe and i40e, initialize XPS on driver load so that we can
take advantage of this kernel feature.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make functions that should be static. While we're at it, fix the function
header comment for fm10k_tlv_attr_nest_stop(), and update the copyright
header for fm10k_pf.h, fm10k_tlv.c and fm10k_tlv.h.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function declaration does not need to be 'inline'd here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses two issues.
First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case. As such we need to add a check
for if it is NULL.
Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the q_vector allocation fails we should free the resources associated
with the MSI-X vector table.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than wrapping fm10k_dcbnl.c and fm10k_debugfs.c support with
#ifdef blocks, just conditionally include the .o files in the Makefile.
Also, since we're modifying it, update the copyright year on the
Makefile.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We haven't bumped the driver version in a while despite many fixes being
pulled in from the out-of-tree Sourceforge driver. Update the version to
match.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using lowercase vlan, vid, or VID, always use VLAN or VLAN ID
in comments when referring to VLANs. The original driver code was
consistent, but recent patches have not been as consistent with this
naming scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve code style by removing the unnecessary else block of an if
statement which immediately returns.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ether_addr_copy function instead of copying byte-by-byte in a
for-loop by hand.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to e1000, e1000e and igb.
Joern Engel fixes up the e1000 driver to reduce scheduler latencies by
making the eeprom read/write functions scheduler friendly by using a mutex
lock instead of a spin lock.
Todd adds code for igb to initialize the 88E1543 PHY properly. Then fixed
igb to use the correct i210 register for EEMNGCTL, since the i210 has two
EEPROM access registers (EEARBC and EEMNGCTL).
Dmitry Vyukov provides a fix for e1000 to resolve a data race found with
KernelThreadSanitizer (KTSAN), where no memory barriers were being used
when buffers get recycled, so the recycled buffers can be corrupted. So
use smp_store_release() to update tx_ring->next_to_clean and
smp_load_acquire() to read tx_ring->next_to_clean to properly hand off
buffers from e1000_clean_tx_irq() to e1000_xmit_frame().
Jarod Wilson fixes igb so that we do not try to unmap a NULL hw_addr. Then
cleaned up array_rd32() so that it uses igb_rd32() the same as rd32() and
use io_addr() in more places so that we do not have to call E1000_REMOVED().
Janusz Wolak cleans up the e1000 driver by correcting warnings produced
by checkpatch.pl for the driver.
Jean Sacren provides several patches with general cleanups for e1000 and
e1000e, which include code comment fix-ups and cleanup of local variables
not needed.
Dmitry Fleytman fixes a possible division by zero in the receive interrupt
handler for e1000e when working without adaptive interrupt moderation,
which is typically disabled on jumbo MTUs.
Raanan increases the timeout of the polling bit due to timing changes to
the ME firmware on a platform, so increase the timeout to 300ms. Added
initial support for i219-LM, which is a LOM that will be available on
systems with the Lewisburg Platform Controller HUB (PCH) chipset.
Jan Beulich fixes a NULL dereference in igb, due to the adapter->vf _data
being NULL while adapter->vfs_allocated_count is non-zero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up array_rd32 so that it uses igb_rd32 the same as rd32, per the
suggestion of Alexander Duyck, and use io_addr in more places, so that
we don't have the need to call E1000_REMOVED (which simply looks for a
null hw_addr) nearly as much.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The combined effect of commits 6423fc3416 ("igb: do not re-init SR-IOV
during probe") and ceee3450b3 ("igb: make sure SR-IOV init uses the
right number of queues") causes VFs no longer getting set up, leading
to NULL pointer dereferences due to the adapter's ->vf_data being NULL
while ->vfs_allocated_count is non-zero. The first commit not only
neglected the side effect of igb_sriov_reinit() that the second commit
tried to account for, but also that of setting IGB_FLAG_HAS_MSIX,
without which igb_enable_sriov() is effectively a no-op. Calling
igb_{,re}set_interrupt_capability() as done here seems to address this,
but I'm not sure whether this is better than sinply reverting the other
two commits.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By using goto statement, we can achieve sharing the same exit path so
that code duplication could be minimized.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to historical reason, 'phy_data' has never been included in the
kernel doc. Fix it so that the requirement could be fulfilled.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use 'That' to replace 'The' so that the comment would make sense.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The checking logic needed some clean-up work, so we rewrite it by
checking for break first. With that change in place, we can even move
the second check for goto statement outside of the loop.
As this is merely a cleanup, no functional change is involved. The
questionable 'tmp != 0xFF' is intentionally left alone.
Mark Rustad and Alexander Duyck contributed to this patch.
CC: Mark Rustad <mark.d.rustad@intel.com>
CC: Alex Duyck <aduyck@mirantis.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i210 has two EEPROM access registers that are located in
non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously
and EEMNGCTL should also be corrected.
Reported-by: Roman Hodek <roman.aud@siemens.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Janusz Wolak <januszvdm@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000_clean_tx_irq cleans buffers and sets tx_ring->next_to_clean,
then e1000_xmit_frame reuses the cleaned buffers. But there are no
memory barriers when buffers gets recycled, so the recycled buffers
can be corrupted.
Use smp_store_release to update tx_ring->next_to_clean and
smp_load_acquire to read tx_ring->next_to_clean to properly
hand off buffers from e1000_clean_tx_irq to e1000_xmit_frame.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was responsible for ~150ms scheduler latencies.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Generate version strings like the PF driver does. This gives us more
flexibility to add suffixes to the version string at build time.
Change-ID: I0a5ca0783dd8fb849516bfc1e37ea070127847bd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch with X722 devices, driver will set wrong PCTYPES
for VF and UDP flows will not fan out.
Change-ID: I04fe4988253b7cd108c9179a643c969764efcb76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.
Since these messages are really for debugging purposes, reclassify
them as such.
Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.
Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver gets unloaded during reset recovery, it's possible
that it will attempt to free resources when they're already free.
Add a check to make sure that the Tx and Rx rings actually exist
before dereferencing them to free resources.
Change-ID: I4d2b7e9ede49f634d421a4c5deaa5446bc755eee
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are created, the MAC address defaults to all zeros, indicating
to the VF driver that it should use a random MAC address. However, the
PF driver was incorrectly adding this zero MAC to the filter table,
along with the VF's randomly generated MAC address.
Check for a good address before adding the default filter. While we're
at it, make the error message a bit more useful.
Change-ID: Ia100947d68140e0f73a19ba755cbffc3e79a8fcf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-12
This series contains updates to ixgbe only.
Alex Duyck provides almost off of the changes in this series. First, add a
check to make sure mac_table was actually allocated and is not NULL to
ensure we do not get a NULL pointer dereference further down the line.
Fixed SR-IOV VLAN pool configuration since the code for checking the PF bit
in ixgbe_set_vf_vlan_msg() was using the wrong offset. Cleanup/simplify
the logic for setting the VFTA register by removing the number of
conditional checks needed. Fixed a number of issues within the VLVF and
VLFB configuration by simplifying the code. Added support for bypassing
the VLVF entry creation when the PF is adding a new VLAN. Reduced the
complexity of the search function used for finding a VLVF entry associated
with a given VLAN ID. Added support for VLAN promiscuous with SR-IOV
enabled by setting all the bits in the VFTA and all of the VLVF bits
associated with teh pool belonging to the PF, in addition to cleaning up
those same bits in the event of promiscuous mode being disabled. Fixed
and issue where we ran the risk of leaking an address into pool 0 which
really belongs to VF 0 when SR-IOV is enabled.
Emil fixes an issue with some X550 devices which can connect at 2.5Gbps,
but only with certain link partners during fail-over, so to avoid
confusion, we do not report it as supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some X550 devices can connect at 2.5Gbps during fail-over, but only
with certain link partners. Also setting the advertised speed will
not work so we do not report it as supported to avoid confusion.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to. What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.
Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface. Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry. What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLAN promiscuous with SR-IOV enabled.
The code prior to this patch was only adding the PF to VLANs that the VF
had added. As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited. This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.
With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF. By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF. In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to reduce the complexity of the search function used
for finding a VLVF entry associated with a given VLAN ID. The previous
code was searching from bottom to top. I reordered it to search from top
to bottom. In addition I pulled an AND statement out of the loop and
instead replaced it with an OR statement outside the loop. This should
help to reduce the overall size and complexity of the function.
There was also some formatting I cleaned up in regards to whitespace and
such.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN. The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues within the VLVF and VLVFB
configuration
First was the fact that code was overly complicated with multiple
conditional paths depending on if we adding or removing and which bit we
were going to add or remove. Instead of messing with all that I have
simplified it by using (vid / 32) and (1 - vid / 32) to identify our
register and the other vlvfb register.
Second was the fact that we were likely leaking a few packets into the PF
in cases where we were deleting an entry and the VFTA filter for that entry
as the ordering was such that we deleted the pool and then the VLAN filter
instead of the other way around. I have updated that by adding a check for
no bits being set and if that occurs we clear things up in the proper
order.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to clear the way for upcoming work I thought it best to drop the
level of indent in the ixgbe_set_vfta_generic function. Most of the code
is held in the virtualization specific section. So the easiest approach is
to just add a jump label and jump past the bulk of the code if it is not
enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the logic for setting the VFTA register by removing
the number of conditional checks needed. Instead we just use some boolean
logic to generate vfta_delta, and if that is set then we xor the vfta by
that value and write it back.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check to make certain mac_table was actually allocated and is not
NULL. If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sensor index should be passed instead of 0. For now, this does not make
a difference, since there is so far only one temperature sensor
exposed by HW.
Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix copy & paste error in MTPM unpack helper.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename en_flow_table.c to en_fs.c in order to be aligned
with the new flow steering files.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the new flow steering API and remove the old
one.
Few changes are required:
1. The Ethernet flow steering follows the existing implementation, but uses
the new steering API. The old flow steering implementation is removed.
2. Move the E-switch FDB management to use the new API.
3. When driver is loaded call to mlx5_init_fs which initialize
the flow steering tree structure, open namespaces for NIC receive
and for E-switch FDB.
4. Call to mlx5_cleanup_fs when the driver is unloaded.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering initialization is based on static tree which
illustrates the flow steering tree when the driver is loaded. The
initialization considers the max supported flow table level of the device,
a minimum of 2 kernel flow tables(vlan and mac) are required to have
kernel flow table functionality.
The tree structures when the driver is loaded:
root_namespace(receive nic)
|
priority-0 (kernel priority)
|
namespace(kernel namespace)
|
priority-0 (flow tables priority)
In the following patches, When the EN driver will use the flow steering
API, it create two flow tables and their flow groups under
priority-0(flow tables priority).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the following objects:
mlx5_flow_root_namespace: represent the root of specific flow table
type tree(e.g NIC receive, FDB, etc..)
mlx5_flow_group: define the mask of the flow specification.
fs_fte(flow steering flow table entry): defines the value of the
flow specification.
The following describes the relationships between the tree objects:
root_namespace --> priorities -->namespaces -->
priorities -->flow-tables --> flow-groups -->
flow-entries --> destinations
When we create new object(flow table/flow group/flow table entry), we
call to the FW command and then we add the related sw object to the tree.
When we destroy object, e.g. call to mlx5_destroy_flow_table, we use
the tree node destructor for destroying the FW object and remove the
node from the tree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the flow steering mlx5_flow_namespace (Namespace)
and fs_prio (Flow Steering Priority) tree nodes.
Namespaces are used in order to isolate different usages or types
of steering (for example, downstream patches will add a different
namespaces for the NIC driver and for E-Switch FDB usages).
Flow Steering Priorities are objects that describes priorities
ranges between different flow objects under the same namespace.
Example, entries in priority i are matched before entries
in priority i+1.
This patch adds the following algorithms:
1) Calculate level:
Each flow table has level(the priority between the flow tables).
When we initialize the flow steering tree, we assign range of levels
to each priority, therefore the level for new flow table is
the location within the priority related to the range of the priority.
2) Match between match criteria. This function is used
for searching flow group when new flow rule is added.
3) Match between match values. This function is used
for searching flow table entry when new flow rule is added.
4) Add essential macros for traversing on a node's children.
E.g. traversing on all the flow table of some priority
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the base data structure and its operations that are
going to represent ConnectX-4 Flow Steering, this data structure
is basically a tree and all Flow steering objects such as
(Flow Table/Flow Group/FTE/etc ..) are represented as fs_node(s).
fs_node is the base object which describes a basic tree node, with the
following extra info:
type: describes the runtime type of the node (Object).
lock: lock this node sub-tree.
ref_count: number of children + current references.
remove_func: a generic destructor.
fs_node types will be used and explained once the usage is added in the
following patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under SRIOV there might be a case where VFs are loaded
without pre-assigned MAC address. In this case, the VF
will randomize its own MAC. This will address the case
of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch capabilities should be queried only if E-Switch flow table
is supported and not only when vport group manager.
Fixes: d6666753c6 ("net/mlx5: E-Switch, Introduce HCA cap and E-Switch vport context")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is introduced in pass-2 chip and with this CQ interrupt
coalescing will work based on both timer and count.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading TCP segmentation to HW in pass-2
revision of hardware. Both driver level SW TSO for pass1.x chips
and HW TSO for pass-2 chip will co-exist. Modified SQ descriptor
structures to reflect pass-2 hw implementation.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch each CPU is associated with its own set of TX queues.
It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err = " assignment is missing here.
Fixes: 0d65fc1304 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.
Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21: expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21: got restricted __le32 *<noident>
This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]
This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.
Looking at that code in more detail to fix the warnings, I see multiple
related problems:
* The conversion functions are not endian-safe, as the DMA descriptors
are almost certainly fixed-endian, but the CPU is not.
* On 64-bit machines, passing a pointer through a u32 variable is a
bug, accessing an indirect pointer as a u32 pointer even more so.
* The handling of epib and psdata mixes native-endian and device-endian
data.
In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cmac_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb90 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc69fdfc6c
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a106 ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Free List DMA Mapping Errors to SGE Queue info for
Free Lists. Add Free List "Low" counter to count the number of times we
see the number of pointers that we _think_ the hardware sees in the
Free List below the Egress Threshold.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WR headers may not fit within one descriptor.
So we need to deal with wrap-around here.
Based on original patch by Pranjal Joshi <pjoshi@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mutual exclusion mechanism to prevent multiple threads of
execution from running in service_ofldq() at the same time. The old
mechanism used an implicit guard on the down-call path and none on the
restart path and wasn't working. This checking makes the mechanism
explicit and is much easier to understand as a result.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper macro ACCESS_ONCE() to load from the SGE status page
to prevent the compiler loading multiple times.
Based on original work by Mike Werner <werner@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mm[cd]_ctrl() and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a mis-order in mlx4 log. Fix it.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have moved on to using allocated pages to carve receive
buffers instead of netdev_alloc_skb() there is no need to store
any pointers for later retrieval. Earlier we had to store
skb and skb->data pointers which later are used to handover
received packet to network stack.
This will avoid an unnecessary cache miss as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same switch-case repeates for nivc_*_intr functions.
In this patch it is moved to a helper nicvf_int_type_to_mask().
By the way:
- Unneeded write to NICVF register dropped if int_type is unknown.
- netdev_dbg() is used instead of netdev_err().
Signed-off-by: Yury Norov <yury.norov@auriga.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Acked-by: Vadim Lomovtsev <Vadim.Lomovtsev@caiumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 driver runs in HA mode, and all VFs are single ported
ones, we make their single port Highly-Available.
This is done by taking advantage of the HA mode properties (following
bonding changes with programming the port V2P map, etc) and adding
the missing parts which are unique to SRIOV such as mirroring VF
steering rules on both ports.
Due to limits on the MAC and VLAN table this mode is enabled only when
number of total VFs is under 64.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource, unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.
Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code reading the MAHR/MALR registers in read_mac_address() is terribly
ineffective -- it reads MAHR 4 times and MALR 2 times, while it's enough to
read each register only once. Use the local variables to achieve that,
somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code reading the MAHR/MALR registers in ravb_read_mac_address() is
terribly ineffective -- it reads MAHR 4 times and MALR 2 times, while
it's enough to read each register only once. Use the local variables to
achieve that, somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'flags' field in bnx2x_stats_arr[] serves only one purpose - to tell
us if the statistic is a per-port stat and thus should not be shown for
virtual functions. It's strange that the field can have three different
values. A boolean will do just fine.
Also remove IS_FUNC_STAT(). It was used only once and it's in fact just
a negation of IS_PORT_STAT().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in MCFW behaviour means that the net driver must update its record
of the warm_boot_count by reading it from the ER_DZ_BIU_MC_SFT_STATUS
register.
On v4.6.x MCFW the global boot count was incremented when some functions
needed to be reset to enable multicast chaining, so all functions saw the
same value. In that case, the driver needed to increment its
warm_boot_count when other functions were reset, to avoid noticing it later
and then trying to reset itself to recover unnecessarily.
With v4.7+ MCFW, the boot count in firmware doesn't change as that is
unnecessary since the PFs that have been reset will each receive an MC
reboot notification. In that case, the driver re-reads the unchanged
value.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx queue #1 frame error counter name contains trailing underscore,
probably due to a typo...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe, i40e/i40evf, MAINTAINERS and e100.txt
Alex provides a fix for ixgbe where enabling SR-IOV and then bringing the
interface up was resulting in the PF MAC addresses getting into a bad state.
The workaround for this issue is to bring up the interface first and then
enable SR-IOV as this will trigger the reset in the existing code.
I clean up legacy license stuff in the e100.txt documentation and then
update the maintainers/reviewers list for our drivers.
Jesse fixes an issue with the i40e/i40evf drivers, where if the driver were
to happen to have a mutex held while the i40e_init_adminq() call was called,
the init_adminq might inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.
This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.
This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.
Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the initializzation code to disable the hardware
vlan support for VLAN Tag stripping by default for now.
Proper support of "hardware VLAN assitance" feature would
soon come in the next coming patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of ethtool TSO option to support
Hip06 SoC to HNS
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "TSO (TCP Segment Offload)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
Enabling this feature would help offload the TCP Segmentation
process to the Hip06 ethernet hardware. This eventually would help
in saving precious cpu cycles.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "RSS (Receive Side Scaling)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
This feature helps in distributing the different flows (mapped as
hash by hardware using Toeplitz Hash) to different Queues asssociated
with the processor cores. The mapping of flow-hash values to the
different queues is stored in indirection table (which is per Packet-
parse-Engine/PPE). This patch also provides the changes to re-program
the (flow-hash<->Qid) mapping using the ethtool.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support of Hisilicon Hip06 SoC to the existing HNS
ethernet driver.
The changes in the driver are mainly due to changes in the DMA
descriptor provided by the Hip06 ethernet hardware. These changes
need to co-exist with already present Hip05 DMA descriptor and its
operating functions. The decision to choose the correct type of DMA
descriptor is taken dynamically depending upon the version of the
hardware (i.e. V1/hip05 or V2/hip06, see already existing
hisilicon-hns-nic.txt binding file for detailed description). other
changes includes in SBM, DSAF and PPE modules as well. Changes
affecting the driver related to the newly added ethernet hardware
features in Hip06 would be added as separate patch over this and
subsequent patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Better to just warn the user that something really odd is going on and
continue to run.
Suggested-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically we return error pointers when we want to use those
pointers in the non-error case, but this function is just
returning error pointers or NULL for success. Change the style to
plain int to follow normal kernel coding styles.
Cc: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation
is to modify the device tree.
This is needed if you plan to use the same kernel with
different ethernet switches, the ones that support the in-band
status and the ones that not.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves autoneg-related bit manipulations to the single place.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai