It's not working reliably if port 3 is enabled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The last set width/height must be preserved as per the spec.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 417 support doesn't work. Until someone can dig into this driver to
figure out why it isn't working the 417 support is disabled.
Sometimes you can actually stream a bit, but very soon the whole machine
crashes, so something is seriously wrong.
For the record, this was not introduced by my recent changes to this driver,
it was broken before that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prefix is generated automatically, so no need to provide it again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Share tuner, frequency, debug and input ioctls with cx231xx-video.
These are all shared resources, so no need to implement them again.
[mchehab@redhat.com: Fix merge conflict and a checkpatch issue]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Colorspace, field and priv were not set, and sizeimage was calculated
using the wrong values (dev->ts1.ts_packet_size and dev->ts1.ts_packet_count
can be 0 at module load).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the initial standard of subdevices instead of leaving it undefined.
Also update the width and height when a new standard is chosen and
return -EBUSY when attempting to change the standard while videobuf is
busy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was already a core lock, so why wasn't ioctl already replaced by
unlock_ioctl?
This patch switches to unlocked_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The use of this field is deprecated since it will not work when multiple
device nodes reference the same video input (the video and vbi nodes in
this case). The norm field should be a device-global value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed to resolve the v4l2-compliance complaints about the control
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various v4l2-compliance fixes: remove unused sliced VBI functions, zero the
reserved fields of struct v4l2_vbi_format and implement the missing s_fmt_vbi_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the tuner clamp the frequency and store that clamped value.
This fixes a v4l2_compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The priv field of v4l2_pix_format must be zeroed. Also fix a bug in try_fmt
where the current width was used instead of the width passed to try_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The g_tuner call wasn't passed on to the subdevices, g_frequency didn't
check for invalid tuners and a low-level function that was expected to
return 0 or a negative error returned a positive number instead, causing
s_frequency to return bogus errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio selection code is broken. Audio and video indices were
mixed up and s_audio would reject changing the audio input to
something else anyway, so what's the point?
All the audio input code has been removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Radio should not use video or audio inputs.
In addition, fix a bug in radio_g_tuner where s_tuner was called in the tuner
subdev instead of g_tuner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the current driver does not implement enumaudio (so apps cannot
tell that audio inputs are present), it does not set V4L2_CAP_AUDIO, nor
does it set audioset when calling ENUM_INPUT. And G_AUDIO doesn't set the
stereo flag either. So these g/s_audio ioctls are quite pointless and
misleading. Especially since some surveillance boards do not have audio
at all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just opening the radio tuner should not cause a switch to the radio tuner.
Only after calling g/s_tuner or g/s_frequency should this happen.
This prevents audio being unmuted as soon as the driver is loaded because
some process opens /dev/radioX just to see what sort of node it is, which
switches on the radio tuner and unmutes audio.
This code can be improved further by actually keeping track of who owns the
tuner and returning -EBUSY if switching tuner modes will cause problems.
But for now just fix the annoying case where on boot the radio turns on
automatically.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
try_fmt_vid_overlay should map incorrect sizes and fields to valid values.
It also expects that an initial overlay size is defined so g_fmt_vid_overlay
returns valid information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The capability field of v4l2_tuner should be ORed by the various subdevs
and by the main driver. In this case the stereo capability was dropped.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probe for additional tvaudio devices, and allow tvaudio+tda7432 to
co-exist. My STB TV PCI FM bttv card has a tda7432, a tda9850 and a
tea6420 and with this patch it finally works again (probably for the
first time in many years).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'current_norm' field cannot be used if multiple device nodes (video and
vbi in this case) set the same std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the private chroma agc control has been replaced with the standard
CHROMA_AGC control.
Also fixes a mute/automute problem where closing the file handle would force
mute on. That's not what you want since that would make the mute state out of
sync with the mute control. Instead check against the user count.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- don't return -EINVAL for invalid field types, handle those as if it
was FIELD_ANY.
- the handling of FIELD_SEQ_BT/TB was wrong as well: if such field formats
aren't supported, then fall back to FIELD_ANY instead of returning an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set an initial frequencies when the driver is loaded. That way G_FREQUENCY will
give a frequency that corresponds with reality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no tuner is present, then disable the tuner and frequency ioctls.
We can remove a number of checks from those ioctls testing for the presence
of a tuner.
Also remove some tuner type checks (now done by the core) and fix an
error return when the prio check fails.
Finally some 'unlikely' statements are removed since those only make sense
in tightly often executed loops, otherwise they just clutter up the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a prerequisite for the G/S_REGISTER ioctls.
In addition, add support to call G/S_REGISTER for supporting i2c devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The querycap ioctl didn't support V4L2_CAP_DEVICE_CAPS and the radio device
implemented audio and video inputs and s_std, which are not part of the radio
API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove two maintainers: telegent.com no longer exists, so those email
addresses are invalid as well.
Added myself as co-maintainer and change the status to 'Odd Fixes'.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ioctl debugging can now be done through the debug parameter in sysfs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a poor administration of the driver state it wasn't possible to open
a video or vbi device multiple times.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usual set of problems: the frequency isn't clamped to the frequency range,
no tuner index check and the frequency isn't initialized properly on module
load.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil