This patch adds Z clock for R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock for R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock divider support for R-Car Gen3 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since v4.15-rc1, the DTS files for all R-Car Gen2 SoCs have been
converted to the new CPG/MSSR bindings. Hence it is now safe to no
longer enable legacy DT clock support by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If a device is part of the CPG/MSSR Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
If a device is part of the CPG/MSTP Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
I seem to have omitted the LVDS clock from the R8A77970 CPG/MSSR support
patch for some reason -- add it back...
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Fixes: 8d46e28fb5 ("clk: renesas: cpg-mssr: Add R8A77970 support")
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJaD3qRAAoJEK0CiJfG5JUlOLgQAKWekgG/IYgcPzPWDYfg8Hwr
sVVUK7+q7TVfbHsbYVikJuUaxutKZ0onnrYmOalTTyyxqL2E1/rYScnxdYHfcwX8
cyfHebRHsbh/Xg45ktwjzBkO49nwuppkpXd/V80GSBUZ+lsIVl5DUrrFAZdRUEdr
CEsAsF9tEWIl+0gqXYNuiKBV7QAYv5BUPrbJQf0PwL6jX0OAhLv+ukfN8BdmYsOb
rdoqhdgmyHkTuIMqsC/H2yP59aAKBse7wxIYebDiTdbPWfTkC9q927fTs4A02F6L
sHfLvCpfuB4rOjXy6LSd1gMGWIcjotZai+idHBqtNLLVz6exF1QpUCp+pZjEULbA
/Sx9lk8A3cYoa8pTu1NrrZbZX17iHkFswqMF3T20nhUN9+Ti597ZEbRcWDcoEZtw
v2NznOTJ7Mm2SrNHOvDklstggNIGcwiAEePGMo7rJNEQZChpDjQj/gJWKzn0UwL4
zfk+0EzoejPdvZ5FJUfmlr8Tqk53uw+y7/0xQ6gf8lDviTrzzoeXtJUyumGBiuGx
RxFywf8n02oLYRJm5hu+0NkC+/bX0Lxg/kwiR6FLBFbBFgkWyp7FGcxhlm6ZiBfe
0KkPciWslNavn5KhljIkZDbXymbvhhSr9uBEFsyeJueA5q7sSghWloL8Ag1cac3W
e6swD1ngXtM/t5gjOLhR
=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration. Register a notifier to save/restore the RCKCR
register during system suspend/resume.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration. Register a notifier to save/restore SDHI clock
registers during system suspend/resume.
This is implemented using the cpg_simple_notifier abstraction, which can
be reused for others clocks that just need to save/restore a single
register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration. Register an (optional) notifier to restore the
DIV6 clock state during system resume.
As DIV6 clocks can be picky w.r.t. modifying multiple register fields at
once, restore is not implemented by blindly restoring the register
value, but by using the existing cpg_div6_clock_{en,dis}able() helpers.
Note that this does not yet support DIV6 clocks with multiple parents,
which do not exist on R-Car Gen3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, possibly
losing clock configuration. Hence add a notifier chain that can be used
by core clocks to save/restore clock state during system suspend/resume.
The implementation of the actual clock state save/restore operations is
clock-specific, and to be registered with the notifier chain in the SoC
or family-specific cpg_mssr_info.cpg_clk_register() callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
During PSCI system suspend, R-Car Gen3 SoCs are powered down, and their
clock register state is lost. Note that as the boot loader skips most
initialization after system resume, clock register state differs from
the state encountered during normal system boot, too.
Hence after s2ram, some operations may fail because module clocks are
disabled, while drivers expect them to be still enabled. E.g. EtherAVB
fails when Wake-on-LAN has been enabled using "ethtool -s eth0 wol g":
ravb e6800000.ethernet eth0: failed to switch device to config mode
ravb e6800000.ethernet eth0: device will be stopped after h/w processes are done.
ravb e6800000.ethernet eth0: failed to switch device to config
PM: Device e6800000.ethernet failed to resume: error -110
In addition, some module clocks that were disabled by
clk_disable_unused() may have been re-enabled, wasting power.
To fix this, restore all bits of the SMSTPCR registers that represent
clocks under control of Linux.
Notes:
- While this fixes EtherAVB operation after resume from s2ram,
EtherAVB cannot be used as an actual wake-up source from s2ram, only
from s2idle, due to PSCI limitations,
- To avoid overhead on platforms not needing it, the suspend/resume
code has a build time dependency on sleep and PSCI support, and a
runtime dependency on PSCI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The RZ family of Renesas SoCs has several different subfamilies (RZ/A,
RZ/G, RZ/N, and RZ/T). Clarify that the renesas,rz-cpg-clocks DT
bindings and clk-rz driver apply to RZ/A1 only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
D3 is S1D2.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
M3-W is S0D3.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
H3 ES2.0 is S0D3.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus fix affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus fix affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car V3M (R8A77970) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add more module clocks for R-Car V2H and M3-W,
- Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
- Add support for the new R-Car D3 SoC,
- Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=77l6
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
* Add more module clocks for R-Car V2H and M3-W,
* Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
* Add support for the new R-Car D3 SoC,
* Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
* Small fixes and cleanups.
* tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add USB3.0 clock
clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY
clk: renesas: cpg-mssr: Add R8A77995 support
clk: renesas: rcar-gen3: Add support for SCCG/Clean peripheral clocks
clk: renesas: rcar-gen3: Add divider support for PLL1 and PLL3
clk: renesas: Add r8a77995 CPG Core Clock Definitions
clk: renesas: rcar-gen3-cpg: Refactor checks for accessing the div table
clk: renesas: rcar-gen3-cpg: Drop superfluous variable
clk: renesas: Allow compile-testing of all (sub)drivers
clk: renesas: r8a7792: Add IMR-LX3/LSX3 clocks
clk: renesas: div6: Document fields used for parent selection
R-Car USB 2.0 controller can change the clock source from an oscillator
to an external clock via a register. So, this patch adds support
the clock source selector as a clock driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.
Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
On R-Car Gen3 SoCs with a Spread Spectrum Clock Generator (e.g. R-Car
D3), a peripheral clock divider has been added, to select between clean
and spread spectrum parents.
Add a new clock type to the R-Car Gen3 driver core to handle this.
To avoid increasing the size of struct cpg_core_clk, both parents and
dividers are stored in the existing parent resp. div fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
On some R-Car Gen3 SoCs (e.g. R-Car D3), PLL1 and PLL3 use a divider
value different from one. Extend struct rcar_gen3_cpg_pll_config to handle
this. As all multipliers and dividers are small, table size increase
can be kept limited by storing them in u8s instead of unsigned ints,
which saves ca. 0.5 KiB for a generic kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Do the checks for accessing the SD divider table only when the rate gets
updated, namely on init and set_rate. In all other cases, reuse the last
value. This simplifies code, runtime load, and error reporting.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
'rate' is not used, so we can use 'parent_rate' directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable compile-testing of the remaining clock drivers and subdrivers,
now dummies are available for of_clk_get_from_provider(),
of_device_compatible_match(), and rcar_rst_read_mode_pins(), and the
CPG/MSSR driver core has been converted from of_match_node() to
of_device_get_match_data().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the missing documentation for the fields in struct div6_clock
related to parent selection for DIV6 clocks with selectable parents, as
found in R/SH-Mobile SoCs.
Fixes: c6d67fb037 ("clk: shmobile: div6: support selectable-input clocks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If CONFIG_OF=n:
drivers/clk/renesas/renesas-cpg-mssr.c: In function ‘cpg_mssr_probe’:
drivers/clk/renesas/renesas-cpg-mssr.c:702: warning: dereferencing ‘void *’ pointer
drivers/clk/renesas/renesas-cpg-mssr.c:702: error: request for member ‘data’ in something not a structure or union
To fix this, use the of_device_get_match_data() helper, for which a
dummy version is provided if CONFIG_OF=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new R-Car E2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car V2H Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car M2-W/N Clock Pulse Generator / Module Standby and
Software Reset driver, using the CPG/MSSR driver core. This will enable
support for module resets, which are not supported by the existing
driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car H2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The goals are to:
- Allow precise control over and automatic selection of which
(sub)drivers are used for which SoC (which may change in the
future),
- Allow adding support for new SoCs easily,
- Allow compile-testing of all (sub)drivers,
- Keep driver selection logic in the subsystem-specific Kconfig,
independent from the architecture-specific Kconfig (i.e. no "select"
from arch/arm64/Kconfig.platforms), to avoid dependencies.
This is implemented by:
- Introducing Kconfig symbols for all drivers and sub-drivers,
- Introducing the Kconfig symbol CLK_RENESAS, which is enabled
automatically when building for a Renesas ARM platform, and which
enables all required drivers without interaction of the user, based
on SoC-specific ARCH_* symbols,
- Allowing the user to enable any Kconfig symbol manually if
COMPILE_TEST is enabled,
- Using the new Kconfig symbols instead of the ARCH_* symbols to
control compilation in the Makefile,
- Always entering drivers/clk/renesas/ during the build.
Note that currently not all (sub)drivers are enabled for
compile-testing, as they depend on independent fixes in other
subsystems.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Coccinelle warns:
drivers/clk/renesas/renesas-cpg-mssr.c:323:14-21: ERROR: PTR_ERR applied after initialization to constant on line 260
Initialize clk using ERR_PTR(-ENOTSUPP) instead of NULL to fix this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cfr. the errata of April 14, 2017, for the R-Car Gen3 Hardware Manual
Rev. 0.53E.
These have no user-visible effect, as the clock frequencies stay the
same.
Fixes: 5573d19412 ("clk: renesas: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The pm_subsys_data.clock_list member exists only if CONFIG_PM_CLK=y.
Hence direct accesses to this field break compile-testing on platforms
where CONFIG_PM_CLK=n.
To fix this, use the pm_clk_no_clocks() helper instead, for which a
dummy version is provided if CONFIG_PM_CLK=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
R-Car V2H does not have "DIV6" programmable clocks, hence there is no
need to build clk-div6.o.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the "intc-ex" clock to the R8A7796 CPG MSSR driver.
According to information from the hardware team the INTC-EX
parent clock is CP. The next data sheet version will include
this information.
[takeshi.kihara.df: Ported from commit f099aa0757 ("clk: shmobile:
r8a7795: Add INTC-EX clock") to drivers/clk/renesas/r8a7796-cpg-mssr.c]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to tables 7.5b and 7.6b of the RZ/G Series Hardware User's
Manual Rev.1.00, MD19=0 is a prohibited setting.
Hence stop looking at MD19, and remove all PLL configurations for
MD19=0.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G1E does not have the SCU-SRC[0789] modules and module clocks.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V2H and E2 do not have the PLL0CR register, but use a fixed
multiplier (depending on mode pins) and divider.
This corrects the clock rate of "pll0" (PLL0 VCO after post divider) on
R-Car V2H and E2 from 1.5 GHz to 1 GHz.
Inspired by Sergei Shtylyov's work for the common R-Car Gen2 and RZ/G
Clock Pulse Generator support core.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Fixes: 0dce5454d5 ("ARM: shmobile: Initial r8a7794 SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Starting with R-Car H3 ES2.0, the parent of RCLK is selected using MD28.
Add support for that, but retain the old behavior for R-Car H3 ES1.x and
M3-W ES1.0 using a quirk.
Inspired by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Clock Pulse Generator / Module Standby and Software Reset module in
R-Car H3 ES2.0 differs from ES1.x in the following areas:
- More core clocks (S0D2, S0D3, S0D6, S0D8, S0D12),
- Different parent clocks for AUDMAC, EtherAVB, FCP, FDP, IMR,
SYS-DMAC, VIN, VSPB, VSPI,
- Removal of modules CSI21, FCPCI, FCPF2, FCPVD3, FCPVI2, FDP1-2,
USB3-IF1, VSPD3, VSPI2,
- Addition of modules EHCI3, HS-USB-IF3, USB-DMAC3-0, USB-DMAC3-1.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
This is achieved by:
- Updating the clock tables for the latest revision (ES2.0), but not
removing clocks that only exist on earlier revisions (ES1.x),
- Detecting the SoC revision at runtime using the new soc_device_match()
API, and fixing up the clocks tables to match the actual SoC
revision, by:
- NULLifying core and module clocks of modules that do not exist,
- Reparenting module clocks that have a different parent on ES1.x.
Based on R-Car Gen3 Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The same SoC may have different clocks and/or module clock parents,
depending on SoC revision. One option is to use different sets of clock
tables for each SoC revision. However, if the differences are small, it
is much more space-efficient to have a single set of clock tables, and
fix those up at runtime instead.
Hence provide three helpers:
- Two helpers to NULLify core and module clocks that do not exist on
some revisions (NULLified clocks are skipped during the registration
phase),
- One helper to reparent module clocks that have different clock
parents.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a workaround for errata on R-Car H3 ES1.0, where the PLL0, PLL2, and
PLL4 clock frequencies are off by a factor of two.
Inspired by a patch by Dien Pham in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Dien Pham <dien.pham.ry@renesas.com>
Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The parent clock of the Audio DMACs is the "ZS" AXI bus clock, which
maps to S3D1 on R-Car H3 ES1.x.
All module clocks must be sorted by clock ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Add the IMR[0-3] clocks to the R8A7795 CPG/MSSR driver.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When there is no status bit, it is possible for the clock enable/disable
operation to have not completed by the time the driver code resumes
execution. This is due to the fact that write operations are sometimes
queued and delayed internally. Doing a read ensures the write operations
has completed.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WluB
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
* tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add IIC-DVFS clock
clk: renesas: r8a7795: Add IIC-DVFS clock
clk: renesas: cpg-mssr: Add support for reset control
clk: renesas: cpg-mssr: Rename cpg_mssr_priv.mstp_lock
clk: renesas: cpg-mssr: Document suitability for RZ/G1
dt-bindings: clock: renesas: cpg-mssr: Document reset control support
clk: renesas: mstp: Reformat cpg_mstp_clock_register() for git diff
clk: renesas: mstp: Make INTC-SYS a critical clock
clk: renesas: cpg-mssr: Migrate to CLK_IS_CRITICAL
Add optional support for the Reset Control feature of the Renesas Clock
Pulse Generator / Module Standby and Software Reset module on R-Car
Gen2, R-Car Gen3, and RZ/G1 SoCs.
This allows to reset SoC devices using the Reset Controller API.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The spinlock is used to protect Read-Modify-Write register accesses,
which won't be limited to SMSTPCR register accesses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver is already in active use for RZ/G1 since
commits c0b2d75d2a ("clk: renesas: cpg-mssr: Add R8A7743 support")
and 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
As the function header of cpg_mstp_clock_register() is split in an
unusual way, "git diff" gets confused when changes to the body of
the function are made, and attributes them to the wrong function.
Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
INTC-SYS is the module clock for the GIC. Accessing the GIC while it is
disabled causes:
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
Currently, the GIC-400 driver cannot enable its module clock for several
reasons:
- It does not use a platform device, so Runtime PM is not an option,
- gic_of_init() runs before any clocks are registered, so it cannot
enable the clock explicitly,
- gic_of_init() cannot return -EPROBE_DEFER, as IRQCHIP_DECLARE()
doesn't support deferred probing.
Hence we have to keep on relying on the boot loader for enabling the
module clock.
To prevent the module clock from being disabled when the CCF core thinks
it is unused, and thus causing a system lock-up, add a check to the MSTP
clock driver and enable CLK_IS_CRITICAL. This will make sure the module
clock is never disabled.
This is a hard dependency for describing the INTC-SYS clock in DT on
R-Mobile APE6 and R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
When the Renesas CPG/MSSR driver was introduced, it was anticipated that
critical clocks would be handled through a new CLK_ENABLE_HAND_OFF flag
soon. However, CLK_ENABLE_HAND_OFF never made it upstream.
Instead, commit 32b9b10961 ("clk: Allow clocks to be marked as
CRITICAL") introduced CLK_IS_CRITICAL, a flag with slightly differing
semantics. Still, it can be used to prevent e.g. the GIC module clock
from being turned off, until the GIC-400 driver has full support for
Runtime PM.
Hence migrate the Renesas CPG/MSSR driver from CLK_ENABLE_HAND_OFF to
CLK_IS_CRITICAL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add RZ/G1E (R8A7745) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add RZ/G1M (R8A7743) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the common R-Car Gen2 (and RZ/G) Clock Pulse Generator / Module
Standby and Software Reset support code, using the CPG/MSSR driver
core.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Correct HDMI parent clock so that the rate of the
HDMI clock is 1/4 rather than 1/2 of the rate of PLL1
as per the v0.52 (Jun, 15) manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All R-Car Gen3 clock drivers now obtain the values of the mode pins from
the R-Car RST driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Fall back to our own private copy of rcar_gen2_read_mode_pins() for
backward-compatibility with old DTs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RESET/WDT module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RESET/WDT module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The intention was to enable the checks if debugging is enabled, not
disabled.
Fixes: f793d1e517 ("clk: shmobile: Add new CPG/MSSR driver core")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 CPG/MSSR driver uses a mix of clk_readl()/clk_writel()
and readl()/writel() to access the clock registers. Settle on the
generic readl()/writel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver core uses a mix of clk_readl()/clk_writel()
and readl()/writel() to access the clock registers. Settle on the
generic readl()/writel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Check the MD_CLK pin to determine the current clock mode in order to set
the pll clock parent correctly.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add all clocks needed to use the SDHI interfaces on the Renesas R-Car M3-W
(r8a7796) SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rh+1
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull renesas r8a7796 SDHI clock support from Geert Uytterhoeven:
Add all clocks needed to use the SDHI interfaces on the Renesas R-Car M3-W
(r8a7796) SoC.
* tag 'clk-renesas-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add SDIF clocks
clk: renesas: r8a7796: Add GPIO clocks
This patch adds SDIF clocks for R8A7796 SoC.
Based on work by Ai Kyuse and Yoshihiro Shimoda for the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add all clocks related to the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0CHq
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Merge r8a7796 watchdog clk support from Geert Uytterhoeven:
Add all clocks related to the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
* tag 'clk-renesas-for-v4.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add watchdog module clock
clk: renesas: r8a7796: Add watchdog core clocks
According to the datasheet, SDn clocks are from the SDSRC clock. And
the SDSRC has a 1/2 divider. So, we should have ".sdsrc" as an internal
core clock. Otherwise, since the sdhi driver will calculate clock for
a sd card using the wrong parent clock rate, and then performance will
be not good.
Fixes: 90c073e539 ("clk: shmobile: r8a7795: Add SD divider support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the module clock for the Watchdog Timer (WDT) controller on the
Renesas R-Car M3-W (r8a7796) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add all core clocks related to the Watchdog Timer (WDT) controller on
the Renesas R-Car M3-W (r8a7796) SoC: OSC, Internal RCLK, and RCLK.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the latest information, the parent clock of the LVDS module
clock is the S0D4 clock, not the S2D1 clock.
Note that this change has no influence on actual operation, as the
rcar-du LVDS encoder driver doesn't use the parent clock's rate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Initial support for R-Car M3-W (r8a7796), including basic core clocks,
and SCIF2 (console) and INTC-AP (GIC) module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Extract the code to support parts common to all members of the R-Car
Gen3 SoC family into a separate file, to ease sharing among SoC-specific
drivers.
Note that while the cpg_pll_configs[] arrays and the selection of the
config based on the MODE bits are identical on R-Car H3 and R-Car M3-W,
they are not common, and may be different on other R-Car Gen3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
As a pure Clock Domain does not have the concept of powering the domain
itself, the CPG/MSTP driver does not provide power_off() and power_on()
callbacks.
However, the genpd core may still perform a dummy power down, causing
/sys/kernel/debug/pm_genpd/pm_genpd_summary to report the domain's
status being "off-0".
Use the always-on governor to make sure the domain is never powered
down, and always shows up as "on" in pm_genpd_summary.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
All local setup of the generic_pm_domain structure should have been
completed before calling pm_genpd_init().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
As a pure Clock Domain does not have the concept of powering the domain
itself, the CPG/MSTP driver does not provide power_off() and power_on()
callbacks.
However, the genpd core may still perform a dummy power down, causing
/sys/kernel/debug/pm_genpd/pm_genpd_summary to report the domain's
status being "off-0".
Use the always-on governor to make sure the domain is never powered
down, and always shows up as "on" in pm_genpd_summary.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
All local setup of the generic_pm_domain structure should have been
completed before calling pm_genpd_init().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The R-Car SYSC PM Domain driver has to power manage devices in power
areas using clocks. To reuse code and to share knowledge of clocks
suitable for power management, this is ideally done through the existing
cpg_mssr_attach_dev() and cpg_mssr_detach_dev() callbacks.
Hence these callbacks can no longer rely on their "domain" parameter
pointing to the CPG/MSSR Clock Domain. To handle this, keep a pointer to
the clock domain in a static variable. cpg_mssr_attach_dev() has to
support probe deferral, as the R-Car SYSC PM Domain may be initialized,
and devices may be added to it, before the CPG/MSSR Clock Domain is
initialized.
Dummy callbacks are provided for the case where CPG/MSTP support is not
included, so the rcar-sysc driver won't have to care about this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Currently the decision whether to build the renesas-cpg-mssr and
clk-mstp drivers is handled by Makefile logic. However, the rcar-sysc
driver will need to know whether CPG/MSSR and/or CPG/MSTP support are
available or not.
To avoid having to duplicate this logic, move it to Kconfig. Provide
non-visible CLK_RENESAS_CPG_MSSR and CLK_RENESAS_CPG_MSTP Kconfig
symbols, which can be used by both Makefiles and C code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Make it clear that the "domain" parameter of the cpg_mstp_attach_dev()
and cpg_mstp_detach_dev() functions is not used.
The cpg_mstp_attach_dev() and cpg_mstp_detach_dev() callbacks are not
only used by the CPG/MSTP Clock Domain driver, but also by the R-Mobile
SYSC PM Domain driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As of commit 71d076ceb2 ("ARM: shmobile: Enable PM and
PM_GENERIC_DOMAINS for SoCs with PM Domains"),
CONFIG_PM_GENERIC_DOMAINS_OF is always enabled for SoCs with a CPG/MSSR
block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
As of commit 71d076ceb2 ("ARM: shmobile: Enable PM and
PM_GENERIC_DOMAINS for SoCs with PM Domains"),
CONFIG_PM_GENERIC_DOMAINS_OF is always enabled for SoCs with MSTP
clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
R can select between two parents. We deal with it like this: During
initialization, check if EXTALR is populated. If so, use it for R. If
not, use R_Internal. clk_mux doesn't help here because we don't want to
switch parents depending on the clock rate. The clock rate (and source)
should stay constant for the watchdog, so I think a setup like this
during initialization makes sense.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gen3 has two clocks (OSC and R) which look like a DIV6 clock but their
divider value is read-only and depends on MD pins at bootup. Add support
for such clocks by reading the value and adding a fixed clock.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
About SD clocks: The clock type is Gen3 specific, the callbacks are all
Gen3 specific; I think the clock definition should also be Gen3 specific
and not in the general header file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Name the #define guarding compilation of this header
__RENESAS_CLK_DIV6_H__ rather than __SHMOBILE_CLK_DIV6_H__.
This is a follow-up to renaming the directory in which this file lives from
shmobile to renesas which is in turn part of an ongoing process to migrate
from ARCH_SHMOBILE to ARCH_RENESAS the motivation for which being that
RENESAS seems to be a more appropriate name than SHMOBILE for the majority
of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Along with the above mentioned Kconfig changes it seems appropriate
to also rename files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Along with the above mentioned Kconfig changes it seems appropriate
to also rename directories that only hold drivers for such SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Takeshi Kihara