Since the switch to using regmap this function no longer takes the
I2C client struct as argument nor do we even interact with the client
anywhere other than when creating the regmap.
Rename it to a less misleading name: "rx8010_init()".
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917114656.9036-1-brgl@bgdev.pl
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Prefer aux-voltage-chargeable over trickle-diode-disable and set diode
accordingly. This is then passed to the chip's appropriate charge setup
function.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-8-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
Make trickle-resistor-ohms optional for charging setups that do not
require specifying ROUT bits (specifying the resistor value between Vcc
and Vbackup). In order to allow specifying that, introduce
requires_trickle_resistor per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-6-bst@pengutronix.de
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits
(7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance
reads:
"To prevent accidental enabling, only a pattern on 1010 enables the
trickle charger. All other patterns disable the trickle charger."
Since not all RTCs connected to a backup battery or supercap use these
bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger
setups unconditionally.
Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1",
"SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4.
DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that
apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So
apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which
is used by both RTCs.
[1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf
[2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
Fix a bug when not specify interrupts property in dts
as follows,
rtc-pcf2127-i2c 1-0051: failed to request alarm irq
rtc-pcf2127-i2c: probe of 1-0051 failed with error -22
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200915073213.12779-1-biwen.li@oss.nxp.com
ds1685_rtc_begin_data_access() tried to access an extended register before
enabling access to it by switching to bank 1. Depending on content in NVRAM
this could lead to an endless loop. While at it fix also switch back to
bank 0 in ds1685_rtc_end_data_access().
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20200910084124.138560-1-tsbogend@alpha.franken.de
The only usage of st_rtc_ops is to assign its address to the ops field
in the rtc_device struct. which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200913122644.35515-1-rikard.falkeborn@gmail.com
We don't need to check the time range manually in set_time(), we can
use range_min and range_max exposed by struct rtc_device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-15-brgl@bgdev.pl
This driver requires SMBUS to work. We can relax this requirement if we
switch to using i2c regmap and let the regmap sub-system figure out how
to talk to the bus.
This also has the advantage of shrinking the code for register updates.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-14-brgl@bgdev.pl
We should generally use probe_new instead of probe when registering i2c
drivers. Convert rx8010 to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-13-brgl@bgdev.pl
Using the size of the variable is preferred over using the size of its
type when allocating memory. Convert the call to devm_kzalloc() in
probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-11-brgl@bgdev.pl
Simple 'dev' looks better then repeated &client->dev and has the added
benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-10-brgl@bgdev.pl
The 'err' local variable in rx8010_init_client() doesn't need to be
initialized.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-9-brgl@bgdev.pl
The time buffer len is used directly in this driver. For readability
it's better to define it as the difference between the date register
offsets and use sizeof() whenever referencing it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-8-brgl@bgdev.pl
All other functions in this driver use 'err' for integer return values.
Do the same in rx8010_set_time() for consistency.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-7-brgl@bgdev.pl
The define values in this driver are close to their names and they are
separated by spaces. Use tabs instead and align all defines.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-6-brgl@bgdev.pl
Move local variables of the same type into a single line for better
readability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-5-brgl@bgdev.pl
The way the driver is implemented is buggy for the (admittedly unlikely)
use case where there are two RTCs with one having an interrupt configured
and the second not. This is caused by the fact that we use a global
rtc_class_ops struct which we modify depending on whether the irq number
is present or not.
Fix it by using two const ops structs with and without alarm operations.
While at it: not being able to request a configured interrupt is an error
so don't ignore it and bail out of probe().
Fixes: ed13d89b08 ("rtc: Add Epson RX8010SJ RTC driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200914154601.32245-2-brgl@bgdev.pl
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200830080937.14367-1-krzk@kernel.org
Original device id would conflict with crypto driver, change it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818063609.39859-1-ran.wang_1@nxp.com
Ensure the OSF flag is cleared on the DS1388 when the clock is set.
Fixes: df11b323b1 ("rtc: ds1307: handle oscillator failure flags for ds1388 variant")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818013543.4283-1-chris.packham@alliedtelesis.co.nz
Similar to the other variants the DS1388 has a bit to stop the
oscillator to reduce the power consumption from VBAT. Ensure that the
oscillator is enabled when the system is up.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200816235731.21071-1-chris.packham@alliedtelesis.co.nz
rs5c313_rtc_init() calls platform_driver_register(), and initializes the
hardware. This is wrong because of two reasons:
1. As soon as the driver has been registered, the device may be
probed. If devm_rtc_device_register() is called before hardware
initialization, reading the current time will fail:
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: registered as rtc0
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: hctosys: unable to read the hardware clock
2. If the platform device does not exist, the driver will still write
to a hardware device that may not be present.
Fix this by moving the hardware initialization sequence to the driver's
.probe() method.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814110731.29029-3-geert+renesas@glider.be
Commit 284e2fa1da ("rtc: rtc-rs5c313: use
devm_rtc_device_register()"), removed the last user of the
driver-specific data. Hence there is no longer a need to set it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814110731.29029-2-geert+renesas@glider.be
cmos_read_alarm() may leave certain fields of a struct rtc_wkalrm
untouched; therefore, these fields contain garbage if not properly
initialized, leading to inconsistent values when converting into
time64_t. This patch to zero initialize the struct before calling
cmos_read_alarm().
Note that this patch is not intended to produce a correct time64_t, it
is only to produce a consistent value. In the case of suspend/resume, a
correct time64_t is not necessary; a consistent value is sufficient to
correctly perform an equality test for t_current_expires and
t_saved_expires. Logic to deduce a correct time64_t is expensive and
hence should be avoided.
Signed-off-by: Victor Ding <victording@google.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814191654.v2.1.Iaf7638a2f2a87ff68d85fcb8dec615e41340c97f@changeid
Drivers:
- ds1374: use watchdog core
- pcf2127: add alarm and pcf2129 support
-----BEGIN PGP SIGNATURE-----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=ZEHC
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle - mostly non urgent driver fixes:
- ds1374: use watchdog core
- pcf2127: add alarm and pcf2129 support"
* tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: pcf2127: fix alarm handling
rtc: pcf2127: add alarm support
rtc: pcf2127: add pca2129 device id
rtc: max77686: Fix wake-ups for max77620
rtc: ds1307: provide an indication that the watchdog has fired
rtc: ds1374: remove unused define
rtc: ds1374: fix RTC_DRV_DS1374_WDT dependencies
rtc: cleanup obsolete comment about struct rtc_class_ops
rtc: pl031: fix set_alarm by adding back call to alarm_irq_enable
rtc: ds1374: wdt: Use watchdog core for watchdog part
rtc: Replace HTTP links with HTTPS ones
rtc: goldfish: Enable interrupt in set_alarm() when necessary
rtc: max77686: Do not allow interrupt to fire before system resume
rtc: imxdi: fix trivial typos
rtc: cpcap: fix range
Fix multiple issues when handling alarms:
- Use threaded interrupt to avoid scheduling when atomic
- Stop matching on week day as it may not be set correctly
- Avoid parsing the DT interrupt and use what is provided by the i2c or
spi subsystem
- Avoid returning IRQ_NONE in case of error in the interrupt handler
- Never write WDTF as specified in the datasheet
- Set uie_unsupported, as for the pcf85063, setting alarms every seconds
is not working correctly and confuses the RTC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200812085114.474903-1-alexandre.belloni@bootlin.com
The PCA2129 is the automotive grade version of the PCF2129.
add it to the list of compatibles.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20200630024211.12782-2-liambeguin@gmail.com
Following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), RTC wake-ups stopped working on Jetson TX2
and Jetson Xavier platforms. The Jetson TX2 uses the max77620 PMIC and
the Jetson Xavier uses max20024 PMIC. Both of these PMICs have the same
max77620 RTC controller.
For the max77620 RTC, the variable 'rtc_irq_from_platform' is defined as
true in the max77686 driver and because of this the IRQ passed to the
max77686 driver for RTC is the PMIC IRQ and not the parent. Hence,
following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), for the max77620 the RTC IRQ within the
PMIC is now getting disabled on entry to suspend and unable to wake the
system up. Fix this by only disabling interrupts on entry to suspend
in the max77686 RTC driver, if the interrupt is the parent interrupt.
Fixes: d8f090dbea ("rtc: max77686: Do not allow interrupt to fire before system resume")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806125431.699339-1-jonathanh@nvidia.com
There's not much feedback when the ds1388 watchdog fires. Generally it
yanks on the reset line and the board reboots. Capture the fact that the
watchdog has fired in the past so that userspace can retrieve it via
WDIOC_GETBOOTSTATUS. This should help distinguish a watchdog triggered
reset from a power interruption.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200727034615.19755-1-chris.packham@alliedtelesis.co.nz
It is not enough to select WATCHDOG_CORE, the watchdog part of the driver
now also depends on WATCHDOG. This is currently the best we can do because
alarm support and watchdog support are mutually exclusive.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20200720075250.1019172-1-alexandre.belloni@bootlin.com
Commit c8ff5841a9 ("rtc: pl031: switch to rtc_time64_to_tm/rtc_tm_to_time64")
seemed to have accidentally removed the call to pl031_alarm_irq_enable
from pl031_set_alarm while switching to 64-bit apis.
Let us add back the same to get the set alarm functionality back.
Fixes: c8ff5841a9 ("rtc: pl031: switch to rtc_time64_to_tm/rtc_tm_to_time64")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200714124556.20294-1-sudeep.holla@arm.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200706062727.18481-1-grandmaster@al2klimov.de
When use goldfish rtc, the "hwclock" command fails with "select() to
/dev/rtc to wait for clock tick timed out". This is because "hwclock"
need the set_alarm() hook to enable interrupt when alrm->enabled is
true. This operation is missing in goldfish rtc (but other rtc drivers,
such as cmos rtc, enable interrupt here), so add it.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1592654683-31314-1-git-send-email-chenhc@lemote.com
The rtc-max77686 device shares the main interrupt line with parent MFD
device (max77686 driver). During the system suspend, the parent MFD
device disables this IRQ to prevent an early event happening before
resuming I2C bus controller.
The same should be done by rtc-max77686 driver because otherwise the
interrupt handler max77686_rtc_alarm_irq() will be called before its
resume function (max77686_rtc_resume()). Such issue is not fatal but
disabling shared IRQ by all users ensures correct behavior.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615161455.4420-1-krzk@kernel.org
Unbreak CPCAP driver, which has one more bit in the day counter
increasing the max. range from 2014 to 2058. The original commit
introducing the range limit was obviously wrong, since the driver
has only been written in 2017 (3 years after 14 bits would have
run out).
Fixes: d2377f8cc5 ("rtc: cpcap: set range")
Reported-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reported-by: Dev Null <devnull@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Merlijn Wajer <merlijn@wizzup.org>
Link: https://lore.kernel.org/r/20200629114123.27956-1-sebastian.reichel@collabora.com
The unicore32 port is removed from the kernel.
There is no point to keep stale RTC driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Subsystem:
- new VL flag for backup switch over
Drivers:
- ingenic: only support device tree
- pcf2127: report battery switch over, handle nowayout
-----BEGIN PGP SIGNATURE-----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=dsKr
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle apart from the ingenic rtc driver rework.
The fixes are mainly minor issues reported by coccinelle rather than
real world issues.
Subsystem:
- new VL flag for backup switch over
Drivers:
- ingenic: only support device tree
- pcf2127: report battery switch over, handle nowayout"
* tag 'rtc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (29 commits)
rtc: pcf2127: watchdog: handle nowayout feature
rtc: fsl-ftm-alarm: fix freeze(s2idle) failed to wake
rtc: abx80x: Provide debug feedback for invalid dt properties
rtc: abx80x: Add Device Tree matching table
rtc: rv3028: Add missed check for devm_regmap_init_i2c()
rtc: mpc5121: Use correct return value for mpc5121_rtc_probe()
rtc: goldfish: Use correct return value for goldfish_rtc_probe()
rtc: snvs: Add necessary clock operations for RTC APIs
rtc: snvs: Make SNVS clock always prepared
rtc: ingenic: Reset regulator register in probe
rtc: ingenic: Fix masking of error code
rtc: ingenic: Remove unused fields from private structure
rtc: ingenic: Set wakeup params in probe
rtc: ingenic: Enable clock in probe
rtc: ingenic: Use local 'dev' variable in probe
rtc: ingenic: Only support probing from devicetree
rtc: mc13xxx: fix a double-unlock issue
rtc: stmp3xxx: update contact email
rtc: max77686: Use single-byte writes on MAX77620
rtc: pcf2127: report battery switch over
...
Driver does not use module parameter for nowayout, so it need to
statically initialize status variable of the watchdog_device based
on CONFIG_WATCHDOG_NOWAYOUT.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200604162602.76524-1-bruno.thomsen@gmail.com
Use dev_pm_set_wake_irq() instead of flag IRQF_NO_SUSPEND to enable
wakeup system feature for both freeze(s2idle) and mem(deep).
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200601071914.36444-1-ran.wang_1@nxp.com
When the user provides an invalid value for tc-diode or
tc-resistor generate a debug message instead of silently
ignoring it.
Signed-off-by: Kevin P. Fleming <kevin+linux@km6g.us>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200530122956.360689-1-kevin+linux@km6g.us
sh5 never became a product and has probably never really worked.
Remove it by recursively deleting all associated Kconfig options
and all corresponding files.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rich Felker <dalias@libc.org>
Enable automatic loading of the module when a Device Tree overlay
specifies a device supported by this driver.
Signed-off-by: Kevin P. Fleming <kevin+linux@km6g.us>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200528114617.166587-1-kevin+linux@km6g.us
rv3028_probe() misses a check for devm_regmap_init_i2c().
Add the missed check to fix it.
Fixes: e6e7376cfd ("rtc: rv3028: add new driver")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200528103950.912353-1-hslester96@gmail.com
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1590370788-15136-2-git-send-email-yangtiezhu@loongson.cn
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1590370788-15136-1-git-send-email-yangtiezhu@loongson.cn
There could be still RTC registers access after RTC suspend
with clock disabled, need to add clock operations for each
RTC API to make sure accessing RTC registers is successfully.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1590113996-31845-2-git-send-email-Anson.Huang@nxp.com
In IRQ handler, ONLY clock enable/disable is called due to
clock prepare can NOT be called in interrupt context, but
clock enable/disable will return failure if prepare count
is 0, to fix this issue, just make SNVS clock always prepared
there, the SNVS clock has no prepare function implemented,
so it won't impact anything.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1590113996-31845-1-git-send-email-Anson.Huang@nxp.com
This add support for the MediaTek MT6358 RTC. Driver using
compatible data to store different RTC_WRTGR address offset.
This replace RTC_WRTGR to RTC_WRTGR_MT6323 in mt6323-poweroff
driver which only needed by armv7 CPU without ATF.
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regulator register specifies how many input clock cycles (minus one)
are contained in one tick of the 1 Hz clock.
Since this register can contain bogus values after the system boots, it
needs to be reset in the probe register, otherwise the RTC may count way
to slow or way too fast.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-7-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The code was returning -ENOENT on any error of platform_get_irq(), even
if it returned a different error.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-6-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 'clk' and 'irq' fields were only ever used in the probe function.
Therefore they can be moved to be simple local variables of the probe
function.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-5-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We can write the wakeup timing parameters as soon as the driver probes,
there's no need to wait the very last moment.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-4-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It makes no sense to request a clock and not enable it even though the
hardware is being used. So the driver now enables the clock in the
probe. Besides, now we can properly handle errors.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-3-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
With the recent work on supporting Device Tree on Ingenic SoCs, no
driver ever probes from platform code anymore, so we can clean a bit
this driver by removing the non-devicetree paths.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200505221336.222313-1-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In function mc13xxx_rtc_probe, the mc13xxx_unlock() is called
before rtc_register_device(). But in the error path of
rtc_register_device(), the mc13xxx_unlock() is called again,
which causes a double-unlock problem. Thus add a call of the
function “mc13xxx_lock” in an if branch for the completion
of the exception handling.
Fixes: e4ae7023e1 ("rtc: mc13xxx: set range")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Link: https://lore.kernel.org/r/20200503182235.1652-1-wu000273@umn.edu
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The 'pengutronix' address is defunct for years. Use the proper contact
address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200502142704.19308-1-wsa@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The MAX77620 doesn't support bulk writes, so make sure the regmap code
breaks bulk writes into multiple single-byte writes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200417170825.2551367-3-thierry.reding@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using devm_platform_ioremap_resource instead of open coding it reduces the
size of the binary.
text data bss dec hex filename
3728 216 0 3944 f68 drivers/rtc/rtc-mt2712.o
3744 216 0 3960 f78 drivers/rtc/rtc-mt2712.o.old
Link: https://lore.kernel.org/r/20200415200021.157118-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/04116352-b464-041c-1939-96440133aa6f@web.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
- New Device Support
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
- New Functionality
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
- Fix-ups
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
- Bug Fixes
- Fix PCI IDs; intel-lpss-pci
-----BEGIN PGP SIGNATURE-----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=hJ2o
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
Subsystem:
- The rtc_time_to_tm and rtc_tm_to_time wrappers have finally been removed and
only the 64bit version remain.
- hctosys now works with drivers compiled as modules
New driver:
- MediaTek MT2712 SoC based RTC
Drivers:
- set range for 88pm860x, au1xxx, cpcap, da9052, davinci, ds1305, ds1374,
mcp5121, pl030, pl031, pm8xxx, puv3, sa1100, sirfsoc, starfire, sun6i
- ds1307: DS1388 oscillator failure detection and watchdog support
- jz4740: JZ4760 support
- pcf85063: clock out pin support
- sun6i: external 32k oscillator is now optional, the range is now handled by
the core, providing a solution for 2034.
-----BEGIN PGP SIGNATURE-----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=6Veu
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"More cleanup this cycle, with the final goal of removing the
rtc_time_to_tm and rtc_tm_to_time wrappers. All the drivers that have
been modified for this now are ready for the end of times (whether it
happens in 2033, 2038, 2106, 2127 or even 4052). There is also a
single new driver and the usual fixes and features.
Summary:
Subsystem:
- The rtc_time_to_tm and rtc_tm_to_time wrappers have finally been
removed and only the 64bit version remain.
- hctosys now works with drivers compiled as modules
New driver:
- MediaTek MT2712 SoC based RTC
Drivers:
- set range for 88pm860x, au1xxx, cpcap, da9052, davinci, ds1305,
ds1374, mcp5121, pl030, pl031, pm8xxx, puv3, sa1100, sirfsoc,
starfire, sun6i
- ds1307: DS1388 oscillator failure detection and watchdog support
- jz4740: JZ4760 support
- pcf85063: clock out pin support
- sun6i: external 32k oscillator is now optional, the range is now
handled by the core, providing a solution for 2034"
* tag 'rtc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (87 commits)
rtc: ds1307: check for failed memory allocation on wdt
rtc: class: remove redundant assignment to variable err
rtc: remove rtc_time_to_tm and rtc_tm_to_time
rtc: sun6i: let the core handle rtc range
rtc: sun6i: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: ds1307: add support for watchdog timer on ds1388
rtc: da9052: switch to rtc_time64_to_tm/rtc_tm_to_time64
rtc: da9052: set range
rtc: da9052: convert to devm_rtc_allocate_device
rtc: imx-sc: Align imx sc msg structs to 4
rtc: fsl-ftm-alarm: report alarm to core
rtc: pcf85063: Add pcf85063 clkout control to common clock framework
rtc: make definitions in include/uapi/linux/rtc.h actually useful for user space
rtc: class: avoid unnecessary lookup in hctosys
dt-bindings: rtc: Convert and update jz4740-rtc doc to YAML
rtc: jz4740: Rename vendor-specific DT properties
rtc: jz4740: Add support for JZ4760 SoC
rtc: class: support hctosys from modular RTC drivers
rtc: pm8xxx: clear alarm register when alarm is not enabled
rtc: omap: drop unused dt-bindings header
...
Currently a failed memory allocation will lead to a null pointer
dereference on point wdt. Fix this by checking for a failed
allocation and just returning.
Addresses-Coverity: ("Dereference null return")
Fixes: fd90d48db0 ("rtc: ds1307: add support for watchdog timer on ds1388")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200403110437.57420-1-colin.king@canonical.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200402110411.508534-1-colin.king@canonical.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DS1388 variant has watchdog timer capabilities. When using a DS1388
and having enabled CONFIG_WATCHDOG_CORE register a watchdog device for
the DS1388.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200330025500.6991-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull EFI updates from Ingo Molnar:
"The EFI changes in this cycle are much larger than usual, for two
(positive) reasons:
- The GRUB project is showing signs of life again, resulting in the
introduction of the generic Linux/UEFI boot protocol, instead of
x86 specific hacks which are increasingly difficult to maintain.
There's hope that all future extensions will now go through that
boot protocol.
- Preparatory work for RISC-V EFI support.
The main changes are:
- Boot time GDT handling changes
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file
I/O, memory allocation, etc.
- Introduce a generic initrd loading method based on calling back
into the firmware, instead of relying on the x86 EFI handover
protocol or device tree.
- Introduce a mixed mode boot method that does not rely on the x86
EFI handover protocol either, and could potentially be adopted by
other architectures (if another one ever surfaces where one
execution mode is a superset of another)
- Clean up the contents of 'struct efi', and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit
firmware implementations to return EFI_UNSUPPORTED from UEFI
runtime services at OS runtime, and expose a mask of which ones are
supported or unsupported via a configuration table.
- Partial fix for the lack of by-VA cache maintenance in the
decompressor on 32-bit ARM.
- Changes to load device firmware from EFI boot service memory
regions
- Various documentation updates and minor code cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
efi/libstub/arm: Fix spurious message that an initrd was loaded
efi/libstub/arm64: Avoid image_base value from efi_loaded_image
partitions/efi: Fix partition name parsing in GUID partition entry
efi/x86: Fix cast of image argument
efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
efi/x86: Ignore the memory attributes table on i386
efi/x86: Don't relocate the kernel unless necessary
efi/x86: Remove extra headroom for setup block
efi/x86: Add kernel preferred address to PE header
efi/x86: Decompress at start of PE image load address
x86/boot/compressed/32: Save the output address instead of recalculating it
efi/libstub/x86: Deal with exit() boot service returning
x86/boot: Use unsigned comparison for addresses
efi/x86: Avoid using code32_start
efi/x86: Make efi32_pe_entry() more readable
efi/x86: Respect 32-bit ABI in efi32_pe_entry()
efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
...
Update MAINTAINERS to cover include/linux/pnp.h and add the linux-acpi
list to the PNP entry in it, add the const modifier to the name field
definition in struct pnp_driver and drop a pointer case in the RTC
CMOS driver that has become redundant (Corentin Labbe).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl6CCnwSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxJ/oP/2lBsEiasuEGPBtMMjruJVvHPNVop+vY
lemr/7Fv6M06OwIpo9u2ZU/0PaQAU/pCtj7qQAbbt3llu77kbuTkGJrYhTHhkNS+
XkpVw9GHntUu8t/mBzs+6eCPoL3n58UQwPvu2AuSZjMrVAN9Qpmyd8uNe76l8Kwx
LFYRyCdork2phFlouLsj/U3MKIN+m4MMyeNMWkGiZnFMra1XuQwLln2XUDtmnf9L
G2tIapyVNmUGrDZogiwPCCjeizJY3JPLawFihDX3cj2SXw6+rhISvaHB5fwamG+m
S1xPWVBOYwOydIqScOzyJ98UQqlU21/LrA2KOHz69zj1//fTT6sx9KjFPJRS4F+E
5dyKBVAVcrTj0ZHMd4H7cKhR6kRgy7E9Iew7pnWnYn16X6mlTdEtSFTUffbSbtL7
IQlt8ae1yzsX3E1cMM+PAFPTAekI5uyDsVKxzy+RtZEs0ND+6JxFDDb2jG2ovvx1
DOrHCMZeBFd11ZNVNJpwBrdIALHRhMqdcScDqw09t1/pZVeUy811zZD0hUpuvemJ
wl6YP9IBonWmi+eVroSgKsH1f8KPLzKP7Vh/OUFatb8RWIYn2SQkc+5cJIXQmiTH
SuyZu0yIMtXbnPVLUp3Dg2pq1q05no0IXqO3sNQa0EbzcrY87LogXuyB3Bm6OPVp
b052qB/2yqop
=PLMG
-----END PGP SIGNATURE-----
Merge tag 'pnp-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull PNP subsystem updates from Rafael Wysocki:
- Update MAINTAINERS to cover include/linux/pnp.h and add the
linux-acpi list to the PNP entry in it
- add the const modifier to the name field definition in struct
pnp_driver
- drop a pointer case in the RTC CMOS driver that has become redundant
All by Corentin Labbe.
* tag 'pnp-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
MAINTAINERS: Add linux-acpi list to PNP
rtc: cmos: remove useless cast for driver_name
PNP: constify driver name
PNP: add missing include/linux/pnp.h to MAINTAINERS
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: a3094fc1a1 ("rtc: imx-sc: add rtc alarm support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/13404bac8360852d86c61fad5ae5f0c91ffc4cb6.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add an RTC driver for the RTC device on Ricoh MFD RC5T619,
which is implemented as a variant of RN5T618.
rtc-range output:
Testing 2000-02-28 23:59:59.
OK
Testing 2038-01-19 03:14:07.
OK
Testing 2069-12-31 23:59:59.
OK
Testing 2099-12-31 23:59:59.
KO RTC_RD_TIME returned 22 (line 138)
Testing 2100-02-28 23:59:59.
KO RTC_SET_TIME returned 34 (line 122)
Testing 2106-02-07 06:28:15.
KO RTC_SET_TIME returned 34 (line 122)
Testing 2262-04-11 23:47:16.
KO RTC_SET_TIME returned 34 (line 122)
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These properties are never set anywhere within any of the upstream
devicetree files, so I assume I'm not breaking the ABI with this change.
Rename vendor-specific DT properties to have the 'ingenic,' prefix,
which they should have had from the start.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200311182318.22154-2-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The WENR feature (set a magic value to enable RTC registers read-write)
first appeared on the JZ4760; the JZ4780 came much later.
Since it would be dangerous to specify a newer SoC's compatible string as
the fallback of an older SoC's compatible string, we add support for the
"ingenic,jz4760-rtc" compatible string in the driver.
This will permit to support the JZ4770 by having:
compatible = "ingenic,jz4770-rtc", "ingenic,jz4760-rtc";
Instead of doing:
compatible = "ingenic,jz4770-rtc", "ingenic,jz4780-rtc";
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200311182318.22154-1-paul@crapouillou.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Due to distribution constraints it may not be possible to statically
compile the required RTC driver into the kernel.
Expand RTC_HCTOSYS support to cover all RTC devices (statically compiled
or not) by checking at the end of RTC device registration whether the
time should be synced.
Signed-off-by: Steve Muckle <smuckle@google.com>
Link: https://lore.kernel.org/r/20191106194625.116692-1-smuckle@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for rtc-omap
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321203737.29850-1-uwe@kleine-koenig.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since the commit 7723f4c ("driver core: platform: Add an error message
to platform_get_irq*()") platform_get_irq() started issuing an error message.
Thus, there is no need to have the same in the driver.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Link: https://lore.kernel.org/r/20200321180838.12729-1-iamkeyur96@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/rtc/rtc-max8907.o: in function `max8907_rtc_probe':
rtc-max8907.c:(.text+0x400): undefined reference to `regmap_irq_get_virq'
max8907 should select REGMAP_IRQ
Fixes: 94c01ab6d7 ("rtc: add MAX8907 RTC driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1584545209-20433-1-git-send-email-clabbe@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use devm_add_action_or_reset() for calls to clk_disable_unprepare(),
which can simplify the error handling, and .remove callback can be dropped.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1584349785-27042-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The FLAG register is at a different location to the other supported RTCs
so this requires an extra case in the existing switch statement.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200207031812.14424-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/rtc/rtc-max8907.o: in function `max8907_rtc_probe':
rtc-max8907.c:(.text+0x400): undefined reference to `regmap_irq_get_virq'
max8907 should select REGMAP_IRQ
Fixes: 94c01ab6d7 ("rtc: add MAX8907 RTC driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now the pnp_driver name is "const char *", there are no need to cast
driver_name.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix this build error when PM_SLEEP is not selected:
drivers/rtc/rtc-mt2712.c:412:10: error: ‘mt2712_pm_ops’ undeclared here (not in a function); did you mean ‘mt2712_rtc_ops’?
412 | .pm = &mt2712_pm_ops,
| ^~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20200317143421.9551-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Also remove the unnecessary error message as the core already prints the
info.
Link: https://lore.kernel.org/r/20200311223956.51352-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some boards, like OrangePi PC2 (H5), OrangePi Plus 2E (H3) and Tanix TX6
(H6) don't have external 32kHz oscillator. Till H6, it didn't really
matter if external oscillator was enabled because HW detected error and
fall back to internal one. H6 has same functionality but it's the first
SoC which have "auto switch bypass" bit documented and always enabled in
driver. This prevents RTC to work correctly if external crystal is not
present on board. There are other side effects - all peripherals which
depends on this clock also don't work (HDMI CEC for example).
Make clocks property optional. If it is present, select external
oscillator. If not, stay on internal.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200308135849.106333-2-jernej.skrabec@siol.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_tm time conversion to allow extending
support after 2106 and properly supporting the STv2 range.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306005809.38530-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PL031 and ST v1 RTC are 32bit seconds counters. STv2 is a BCD RTC
apparently going from 0000 to 9999, hopefully handling the leap days
properly until then.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306005809.38530-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The datasheet states that 4052 is the maximum value for year. However, the
mpc5121 read_time and set_time function abuse the target time register
instead of using the broken down time so it is limited to 2106.
Link: https://lore.kernel.org/r/20200306074404.58909-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Link: https://lore.kernel.org/r/20200306073404.56921-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The CPCAP rtc is a 14bit day counter plus a 17bit seconds counter.
Note that this failed on Nov 10 2014 so it is very likely this driver as
never been used since.
Link: https://lore.kernel.org/r/20200306015703.42101-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Both RTC IRQs are requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the IRQs using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Link: https://lore.kernel.org/r/20200306010146.39762-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle offsetting and windowing the RTC range.
This rtc has hours, minutes, seconds and 16bit days. As the driver has the
RTC epoch set to year 2000, this means that the end of the range is 2^16
days minus one second later. This is Sun Jun 6 23:59:59 UTC 2179. This
is better than the currently set year 2099.
Link: https://lore.kernel.org/r/20200305215022.32533-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The code handling invalid alarms meaning the alarm is in the next 24 hours
is not necessary since commit f8245c2688 ("rtc: remove "RTC_ALM_SET mode"
bugs") which actually predates this driver. Since then, .set_alarm is never
called with an invalid alarm and this handling is not necessary in the
driver.
Link: https://lore.kernel.org/r/20200305215022.32533-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC is a 32bit counter running at 16Hz. This overflows every eight
years and a half. However, the driver uses the SW_VALUE register to store
the overflow, extending the counter to 64bit as long as the update happens
before the overflow.
Link: https://lore.kernel.org/r/20200305160452.27808-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drop the separate driver that registers the EFI rtc on all EFI
systems that have runtime services available, and instead, move
the registration into the core EFI code, and make it conditional
on whether the actual time related services are available.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
clear the alarm interrupt status bit immediately after the interrupt is
triggered.This is due to the sticky nature of the alarm interrupt status
register. The alarm interrupt status register can be cleared only after
the second counter outruns the set alarm value. To fix multiple spurious
interrupts, disable alarm interrupt in the handler and clear the status
bit before enabling the alarm interrupt.
Fixes: 11143c19eb ("rtc: add xilinx zynqmp rtc driver")
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/1581503079-387-1-git-send-email-srinivas.neeli@xilinx.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The alignment of the continuation of the devm_ioremap() call in
sh_rtc_probe() was broken. Join the lines, as all parameters can fit on
a single line.
Fixes: 4bdc0d676a ("remove ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200212084836.9511-1-geert+renesas@glider.be
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
Subsystem:
- the VL_READ and VL_CLR ioctls are now documented and their behavior is
unified across all the drivers.
- RTC_I2C_AND_SPI Kconfig option rework to avoid selecting both REGMAP_I2C and
REGMAP_SPI unecessarily.
Drivers:
- at91rm9200: remove deprecated procfs, add sam9x60, sama5d4 and sama5d2
compatibles.
- cmos: solve lost interrupts issue on MS Surface 3
- hym8563: return proper errno when time is invalid
- rv3029: many fixes, nvram support
-----BEGIN PGP SIGNATURE-----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=e1Xr
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The VL_READ and VL_CLR ioctls have been reworked to be more useful.
This will not break userspace as there are very few users and they are
using the integer value as a boolean.
Apart from that, two drivers were reworked and a few fixes here and
there for a net reduction of number of lines.
Summary:
Subsystem:
- the VL_READ and VL_CLR ioctls are now documented and their behavior
is unified across all the drivers.
- RTC_I2C_AND_SPI Kconfig option rework to avoid selecting both
REGMAP_I2C and REGMAP_SPI unecessarily.
Drivers:
- at91rm9200: remove deprecated procfs, add sam9x60, sama5d4 and
sama5d2 compatibles.
- cmos: solve lost interrupts issue on MS Surface 3
- hym8563: return proper errno when time is invalid
- rv3029: many fixes, nvram support"
* tag 'rtc-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (63 commits)
dt-bindings: rtc: at91rm9200: document clocks property
rtc: i2c/spi: Avoid inclusion of REGMAP support when not needed
rtc: Kconfig: select REGMAP_I2C when necessary
rtc: Kconfig: properly indent sd3078 entry
rtc: cmos: Refactor code by using the new dmi_get_bios_year() helper
rtc: cmos: Use predefined value for RTC IRQ on legacy x86
rtc: cmos: Stop using shared IRQ
rtc: tps6586x: Use IRQ_NOAUTOEN flag
rtc: at91rm9200: use FIELD_PREP/FIELD_GET
rtc: at91rm9200: avoid time readout in at91_rtc_setalarm
rtc: at91rm9200: move register definitions to C file
rtc: at91rm9200: add sama5d4 and sama5d2 compatibles
dt-bindings: rtc: at91rm9200: convert bindings to json-schema
rtc: at91rm9200: remove procfs information
dt-bindings: atmel, at91rm9200-rtc: add microchip, sam9x60-rtc
rtc: pcf8563: Use BIT
rtc: moxart: Convert to SPDX identifier
rtc: ds1343: Remove unused struct spi_device in struct ds1343_priv
rtc: rx8025: Remove struct i2c_client from struct rx8025_data
rtc: hym8563: Read the valid flag directly instead of caching it
...
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAl44Ga0ACgkQUa+KL4f8
d2HRJg//VdigHgOTX/eJggI67n36kTgho+VzwRwLuSedDBFIkh5S8NWO7bFyf1Y4
Qn+MybJtCvPQeUVmqO6cUi0/VqXgwW4mUe5L6oQKIsPYzfmhuc/XF+DA2S8ulOBj
CckAM15i4WARCtNtFH12EaGGekLPAkik9nZE5EH7vS89TUxLMKbir72U+qFju6mu
o2F8B7QbDe2jxaooxZ11zPjECwJfzgdXe+FipmogL1itLT+1phpirlttY4R5/4LV
t3jKb3GI5xN+YWqyXHFF1EKtQEHTkYyKcby2It+8ksYAKiueY0hAuX7+pt1KXWjb
ReM/hYH5dqjJSz6MjajrInHlpAf8iqtzNdXznSm/hQ9X+YHpaqmdYBt9bTg3pbR/
z5F0q32e716K/XcJIv2igizT2EZDZIb2AG9oh0D93Z10tPgTpp0CTkcSsSw4CpnP
MM60B2RN6RI/1MVK1eWRfWVSLbopsForetlnwXhTxY0Zr/7Hd+l+2ndz8IJE+vya
86jq9yXv7kndwcKNIuUy5jIE2XV9JIbjwwDd4a8tbQgOMkSWHuV3pN+qnT6+/kRh
TS/LFI49rjJauB85XdqhZc2+i0Eo78ctIdxQebKNZe6wz+r5Y5NTMMCZ5TjScxJX
aSKRepOEtSbnKloUi5HZ71zfX/waTxzgyodkF7UJk3eEtzlDF8o=
=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Merely enabling I2C and RTC selects REGMAP_I2C and REGMAP_SPI, even when
no driver needs it. While the former can be moduler, the latter cannot,
and thus becomes built-in.
Fix this by moving the select statements for REGMAP_I2C and REGMAP_SPI
from the RTC_I2C_AND_SPI helper to the individual drivers that depend on
it.
Note that the comment for RTC_I2C_AND_SPI refers to SND_SOC_I2C_AND_SPI
for more information, but the latter does not select REGMAP_{I2C,SPI}
itself, and defers that to the individual drivers, too.
Fixes: 080481f54e ("rtc: merge ds3232 and ds3234")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200112171349.22268-1-geert@linux-m68k.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Refactor code by using the new dmi_get_bios_year() helper instead of
open coding its functionality. This also makes logic slightly clearer.
No changes intended.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When legacy devices are present on x86 machine, the RTC IRQ has
a dedicated pre-defined value. Use it instead of hard coded number.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As reported by Guilherme G. Piccoli:
---8<---8<---8<---
The rtc-cmos interrupt setting was changed in the commit 079062b28f
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28f ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1 ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs")
Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ_NOAUTOEN flag tells interrupt core that interrupt shall not be
auto-enabled at the time of requesting interrupt. This is a minor clean-up
change that doesn't fix any problems.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106015615.12602-1-digetx@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ROHM BD71828 PMIC RTC block is from many parts similar to one
on BD70528. Support BD71828 RTC using BD70528 RTC driver and
avoid re-inventing the wheel.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The header was simply moved from the arm mach folder to drivers/rtc but
there is not point in having it separated from the driver.
Also remove unused bit definitions and use BIT and GENMASK.
Link: https://lore.kernel.org/r/20191229204421.337612-4-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Our chosen byte swapping, which is what firmware already uses, is to
do readl/writel by normal lw/sw intructions (data invariance). This
also means we need to mangle addresses for u8 and u16 accesses. The
mangling for 16bit has been done aready, but 8bit one was missing.
Correcting this causes different addresses for accesses to the
SuperIO and local bus of the IOC3 chip. This is fixed by changing
byte order in ioc3 and m48rtc_rtc structs.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
struct i2c_client can be referenced from the device structure, so this
doesn't need to have it in struct rx8025_data.
Remove struct i2c_client from struct rx8025_data.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191218081624.3307752-1-iwamatsu@nigauri.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC has a valid bit in the seconds register that indicates whether
power was lost since the pevious time set. This bit is currently read
once at probe time, cached and updated with set_time.
Howeever, caching the bit may prevent detecting power loss at runtime
(which can happen if the RTC's supply is distinct from the the platform's).
Writing the seconds register when setting time will clear the bit,
so there should be no downside in reading the bit directly instead of
caching it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191212153111.966923-2-paul.kocialkowski@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The current code returns -EPERM when the voltage loss bit is set.
Since the bit indicates that the time value is not valid, return
-EINVAL instead, which is the appropriate error code for this
situation.
Fixes: dcaf038493 ("rtc: add hym8563 rtc-driver")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20191212153111.966923-1-paul.kocialkowski@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the current code, the return value of devm_request_threaded_irq may be
returned. This fixes it.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Link: https://lore.kernel.org/r/20191217121231.2698817-2-iwamatsu@nigauri.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Bartosz Golaszewski