We enable the DPLL refclock already when bringing up the cmnlane power
well, so also leave it on when otherwise disabling the DPLL.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Punit seems a bit WIP still. Disable cdclk changes until we have
hardware where it works.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like the Punit is supposed to support the 400MHz cdclk directly on
chv, so we don't need the vlv tricks.
FIXME: Punit doesn't seem ready for this yet on current hw
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the specifications bit 6 is actually valid in the stride register.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both VLV and CHV handle the cmnreset stuff in the power well code now,
so intel_reset_dpio() is no longer needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Share the waitqueue that drm_irq uses when performing the vblank evade
trick for atomic pipe updates.
v2: Keep intel_pipe_handle_vblank() (Chris)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding relevant read out comparison code, in check_crtc_state, for the new
member of crtc_config, dp_m2_n2, which was introduced to store link_m_n
values for a DP downclock mode (if available). Suggested by Daniel.
v2: Changed patch title.
Daniel's review comments incorporated.
Added relevant state readout code for M2_N2. dp_m2_n2 comparison to be done
only when high RR is not in use (This is because alternate m_n register
programming will be done only when low RR is being used).
v3: Modified call to get_m2_n2 which had dp_m_n as param by mistake.
Compare dp_m_n and dp_m2_n2 for gen 7 and below. compare the structures
based on DRRS state for gen 8 and above.
Save and restore M2 N2 registers for gen 7 and below
v4: For Gen>=8, check M_N registers against dp_m_n and dp_m2_n2 as there is
only one set of M_N registers
v5: Removed the chunk which saves and restores M2_N2 registers. Modified
get_m_n() to get M2_N2 registers as well. Modified the macro which compares
hw.dp_m_n against sw.dp_m2_n2/sw.dp_m_n for gen > 8.
v6: Added check to compare dp_m2_n2 only when DRRS is enabled
v7: Modified drrs check to use has_drrs
v8: Add has_drrs check before reading M2_N2 registers
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.
v2: Patch rebased
v3: Daniel's review comments
- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
track drrs support
v4: Jesse's review comments
- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we merged runtime PM support for DPMS, it is possible that these
assertions will be called when the power wells are disabled but a mode
is "set", resulting in "failed assertion" and "device suspended while
reading register" WARNs.
To reproduce the bug: disable all screens using mode unset, do a
modeset on one screen, disable it using DPMS, then try to do a mode
unset on it again to see the WARNs.
v2: The first version of this patch changed the assertions to also
check the power domains. Daniel suggested that it would be better to
just remove the assertions: "The modeset state checker
will already notice when we've failed to turn off the pipe. And we
check cursors and plane state in the enable sequence, too. Since we
use these asserts a lot to lock down the precise modeset sequence I
actually prefer if they're a bit dumb and don't check the power
wells."
Testcase: igt/rpm_rpm/dpms-mode-unset-lpsp
Testcase: igt/rpm_rpm/dpms-mode-unset-non-lpsp
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we use the runtime IRQ enable/disable functions in our suspend
path, we can simply check the pm._irqs_disabled flag everywhere. So
rename it to catch the users, and add an inline for it to make the
checks clear everywhere.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't write it, otherwise we will trigger unclaimed register
errors.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP MST will need connectors that aren't connected to specific
encoders, add some checks in advance to avoid oopses.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
commit 98ec77397a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 30 17:43:01 2014 +0300
drm/i915: Make primary_enabled match the actual hardware state
introduced more accurate tracking of the primary plane and some
checks. It missed the plane->pipe reassignement code for gen2/3
though, which the checks caught and resulted in WARNING backtraces.
Since we only use this path if the plane is on and on the wrong pipe
we can just always set the tracking bit to "enabled".
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
drm/i915: do not setup backlight if not available according to VBT
caused a regression on the HP Chromebook 14 (with Celeron 2955U CPU),
which has a misconfigured VBT. Apply quirk to ignore the VBT backlight
presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV and CHV disable the DP port only in the .post_disable() hook, so we
need to make intel_sanitize_encoder() call that when it's trying to
disable encoders without an active pipes.
My bsw actaully hits this when an external display is connected. The
BIOS still likes to turn on the eDP port, but leaves the pipe disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Remove now bogus comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we already do in haswell_get_pipe_config(). This should
prevent some WARNs when we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we now have support for shared DPLLS.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently still with a redudant WARN_ON in there, the common shared
dpll code will take care of this in the future.
Also we need to flip the switch for the transitional hack now to make
sure that we disable the right pll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still tacked onto the side, but slowly getting there.
v2: Don't forget the debugfs file.
v3 (from Paulo): Don't forget to check the power domains.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And get/put it when needed. The special thing about this commit is
that it will now return false in ibx_pch_dpll_get_hw_state() in case
the power domain is not enabled. This will fix some WARNs we have when
we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla:https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just filing in names and ids, but not yet officially registering them
so that the hw state cross checker doesn't completely freak out about
them. Still since we do already read out and cross check
config->shared_dpll the basics are now there to flesh out the wrpll
shared dpll implementation.
The idea is now to roll out all the callbacks step-by-step and then at
the end switch to the shared dpll framework. This way hw and sw
changes are clearly separated.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: added const to hsw_ddi_pll_names (Damien)]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL disabling
into the post_disable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT post_disable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL enabling
into the pre_enable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT pre_enable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other checks also check hw state, so checking our software
refcounts for the plls looks a bit odd. Also this will simplify the
conversion over to the shared dpll framework, which itself has massive
amounts of checks to make sure that we never leave a display pll
enabled when we shouldn't.
So after that conversion we should stil have a good enough coverage of
asserts for entering pc8/runtime pm on hsw/bdw.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add !mutex_is_locked() checks to intel_pin_and_fence_fb_obj() and
intel_unpin_fb_obj() to help catch failures to grab struct_mutex when
operating on fb objects.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_primary_plane_{setplane,disable} were lacking struct_mutex locking
around their GEM operations.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function can be used to write anything on D_COMP, not just
disable it, so print a more appropriate message.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Toshiba CB35 Chromebook (with Celeron 2955U CPU) has a controllable
backlight although its VBT reports otherwise. Apply quirk to ignore the
backlight presence check during backlight setup.
Patch tested by author on Toshiba CB35.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä