Currently after doing DPMS-OFF on all outputs CDCLK won't be set to its
minimum value as it should. A subsequent modeset to turn off all outputs
will thus run with all power domains disabled, and notice that it needs
to change CDCLK to its minimum value. Since the power domains are
disabled this will emit a register-access-while-suspended WARN and fail
to set the minimum freq.
The proper solution for this is to set the minimum frequency during
DPMS-OFF. That needs a bigger rework that would take into account the
user DPMS setting too during the calculation of the new modesetting
configuration. Until that's done this stop-gap solution gets the PIPE-A
power domain during setting the CDCLK; this domain covers the HW blocks
needed for this.
Idea to use PIPE-A domain from Ville.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Makes it easier to debug infoframe mismatches.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
For MMIO registers which are shadowed, force wake is not needed to
write to these registers.
v2: Rebase on top of nightly (Damien)
v3: Rebase on top of "Gen9 multiple-engine forcewake" changes
v4: (Mika, Bob, done by Damien)
- Reorder the shadowed registers by popularity
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable multi-engine forcewake for Gen9.
v2: (Damien)
- Rebase on top of nightly
- Move the register range definitions to intel_uncore.c
- Whitespace fixes
v3: (Addressing Mika's comment, done by Damien)
- Use REG_RANGE() (introduced after the patch was written)
- Add a SKL_NEEDS_FORCE_WAKE() macro that gets rid of a useless
comparison to FORCEWAKE (reg 0xa18c is not used on SKL)
v4: (Damien)
- Use newly introduced ASSIGN_READ/WRITE_MMIO_VFUNCS() macros
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to read the status of the power wells right after taking forcewake
for the other register reads makes little sense. Most of the time the
power wells will still be up due to the recent forcewake. Instead do the
power well status read first, and only then read the register needing
forcewake. This way the reported power well status can actually reflect
what's going on in the system.
Cc: Deepak S <deepak.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just throw in the towel on this one and take the cheap way out.
Based on a patch from Chris Wilson, but checking for a different bit.
Chris' patch checked for even bank layout, this one here for a magic
bit. Given the evidence we've gathered (not much) both work I think,
but checking for the magic bit might be more accurate.
Anyway, works on my gm45 here.
For paranoi restrict to gen4 (and mobile), since we've only ever seen
this on gm45 and i965gm.
Also add some debugfs output so that we can skip the tiled swapping
tests properly in these cases.
v2: Clean up the quirk'ed pin count in free_object to avoid upsetting
the WARN_ON. Spotted by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28813
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45092
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In __gen6_update_ring_freq, use the full range of
possible gpu frequencies from max_freq to min_freq.
The actual gpu frequency could be outside the range
from max_freq_softlimit to min_freq_softlimit due
to power/thermal constraints.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In gen8_enable_rps, change the initial rps setting
to the min_freq_softlimit (same as gen6_enable_rps).
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set the min_freq_softlimit to max(RPe, 450MHz).
Setting a floor can ensure a minimum experience
level. The 450MHz value came from a power and
performance study of various types of workloads
(3D, Media, GPGPU, idle, etc).
v2: rebased
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found one more!
With this we can clear up the ggtt init code a bit, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With this all the ums nonsense around gem setup/teardown has
disappeared, yay!
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Again just complicates gem init functions and makes a general mess out
of everything.
Good riddance!
v2: In my enthusiasm to start removing dri1/ums crud I went overboard a
bit and killed parts of hangcheck. Resurrect it.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We've killed ums support by now, it's time to reap the benefits. This
one here is getting in the way of doing some ring init cleanup.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
KMS always intializes, this was only a valid check when userspace
was still in control of the kernel driver.
v2: Comment that we outright reject all dri1/ums params.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whether we'll reject them or no-op doesn't really matter ...
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.
v2: Also remove the DRI1 sarea updates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as with the context, pinning to GGTT regardless is harmful (it
badly fragments the GGTT and can even exhaust it).
Unfortunately, this case is also more complex than the previous one
because we need to map and access the ringbuffer in several places
along the execbuffer path (and we cannot make do by leaving the
default ringbuffer pinned, as before). Also, the context object
itself contains a pointer to the ringbuffer address that we have to
keep updated if we are going to allow the ringbuffer to move around.
v2: Same as with the context pinning, we cannot really do it during
an interrupt. Also, pin the default ringbuffers objects regardless
(makes error capture a lot easier).
v3: Rebased. Take a pin reference of the ringbuffer for each item
in the execlist request queue because the hardware may still be using
the ringbuffer after the MI_USER_INTERRUPT to notify the seqno update
is executed. The ringbuffer must remain pinned until the context save
is complete. No longer pin and unpin ringbuffer in
populate_lr_context() - this transient address is meaningless and the
pinning can cause a sleep while atomic.
v4: Moved ringbuffer pin and unpin into the lr_context_pin functions.
Downgraded pinning check BUG_ONs to WARN_ONs.
v5: Reinstated WARN_ONs for unexpected execlist states. Removed unused
variable.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until now, we have pinned every logical ring context backing object
during creation, and left it pinned until destruction. This made my life
easier, but it's a harmful thing to do, because we cause fragmentation
of the GGTT (and, eventually, we would run out of space).
This patch makes the pinning on-demand: the backing objects of the two
contexts that are written to the ELSP are pinned right before submission
and unpinned once the hardware is done with them. The only context that
is still pinned regardless is the global default one, so that the HWS can
still be accessed in the same way (ring->status_page).
v2: In the early version of this patch, we were pinning the context as
we put it into the ELSP: on the one hand, this is very efficient because
only a maximum two contexts are pinned at any given time, but on the other
hand, we cannot really pin in interrupt time :(
v3: Use a mutex rather than atomic_t to protect pin count to avoid races.
Do not unpin default context in free_request.
v4: Break out pin and unpin into functions. Fix style problems reported
by checkpatch
v5: Remove unpin_lock as all pinning and unpinning is done with the struct
mutex already locked. Add WARN_ONs to make sure this is the case in future.
Issue: VIZ-4277
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer create a work item to clean each execlist queue item.
Instead, move retired execlist requests to a queue and clean up the
items during retire_requests.
v2: Fix legacy ring path broken during overzealous cleanup
v3: Update idle detection to take execlists queue into account
v4: Grab execlist lock when checking queue state
v5: Fix leaking requests by freeing in execlists_retire_requests.
Issue: VIZ-4274
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling the RPS interrupts there is a tricky dependency between
the thread disabling the interrupts, the RPS interrupt handler and the
corresponding RPS work. The RPS work can reenable the interrupts, so
there is no straightforward order in the disabling thread to (1) make
sure that any RPS work is flushed and to (2) disable all RPS
interrupts. Currently this is solved by masking the interrupts using two
separate mask registers (first level display IMR and PM IMR) and doing
the disabling when all first level interrupts are disabled.
This works, but the requirement to run with all first level interrupts
disabled is unnecessary making the suspend / unload time ordering of RPS
disabling wrt. other unitialization steps difficult and error prone.
Removing this restriction allows us to disable RPS early during suspend
/ unload and forget about it for the rest of the sequence. By adding a
more explicit method for avoiding the above race, it also becomes easier
to prove its correctness. Finally currently we can hit the WARN in
snb_update_pm_irq(), when a final RPS work runs with the first level
interrupts already disabled. This won't lead to any problem (due to the
separate interrupt masks), but with the change in this and the next
patch we can get rid of the WARN, while leaving it in place for other
scenarios.
To address the above points, add a new RPS interrupts_enabled flag and
use this during RPS disabling to avoid requeuing the RPS work and
reenabling of the RPS interrupts. Since the interrupt disabling happens
now in intel_suspend_gt_powersave(), we will disable RPS interrupts
explicitly during suspend (and not just through the first level mask),
but there is no problem doing so, it's also more consistent and allows
us to unify more of the RPS disabling during suspend and unload time in
the next patch.
v2/v3:
- rebase on patch "drm/i915: move rps irq disable one level up" in the
patchset
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we first enable the RPS interrupts then we clear any pending ones.
By this we could lose an interrupt arriving after we unmasked it. This
may not be a problem as the caller should handle such a race, but logic
still calls for the opposite order. Also we can delay enabling the
interrupts until after all the RPS initialization is ready with the
following order:
1. disable left-over RPS (earlier via intel_uncore_sanitize)
2. clear any pending RPS interrupts
3. initialize RPS
4. enable RPS interrupts
This also allows us to do the 2. and 4. step the same way for all
platforms, so let's follow this order to simplifying things.
Also make sure any queued interrupts are also cleared.
v2:
- rebase on the GEN9 patches where we don't support RPS yet, so we
musn't enable RPS interrupts on it (Paulo)
v3:
- avoid enabling RPS interrupts on GEN>9 too (Paulo)
- clarify the RPS init sequence in the log message (Chris)
- add POSTING_READ to gen6_reset_rps_interrupts() (Paulo)
- WARN if any PM_IIR bits are set in gen6_enable_rps_interrupts()
(Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable the RPS interrupts for all platforms at the same spot, so
move it one level up in the callstack to simplify things.
No functional change.
v2:
- rebase on the GEN9 patches where RPS isn't supported yet, so we don't
need to disable RPS interrupts on it (Paulo)
v3:
- avoid disabling the interrupts on GEN>9 too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This extends
commit 132f3f1767
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Nov 10 15:34:33 2014 +0200
drm/i915: WARN if we receive any gen9 rps interrupts
to GEN>9 platforms as suggested by Paulo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using the universal plane interface, the source rectangle
coordinates define the panning offset for the primary plane, which needs
to be stored in crtc->{x,y}. The original universal plane code
negelected to set these panning offset fields, which was partially
remedied in:
commit ccc759dc2a
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Sep 24 14:20:22 2014 -0300
drm/i915: Merge of visible and !visible paths for primary planes
However the plane source coordinates are provided in 16.16 fixed point
format and the above commit forgot to convert back to integer
coordinates before saving the values. When we replace
intel_pipe_set_base() with plane->funcs->update_plane() in a future
patch, this bug becomes visible via the set_config entrypoint as well as
update_plane.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Testcase: igt/kms_plane
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do in the HDMI code, set the infoframe flag if we detect
that infoframes are enabled.
v2: check for actual infoframe status as in hdmi code (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In sandybridge_pcode_read and sandybridge_pcode_write,
extend the mbox parameter from u8 to u32.
On Haswell and Sandybridge, bits 7:0 encode the mailbox
command and bits 28:8 are used for address control for
specific commands.
Based on suggestion from Ville Syrjälä.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For whatever reasons this can happen. For real testcases the test will
notice the -EIO and fall over, but we also have some testcases that
just read all debugfs files. And that shouldn't cause dmesg spam.
So tune it down a bit so that we still have the information for
debugging. And change the errno so that real testcases can easily
differentiate.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84890
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With multiple rings, we may continue to render on the blitter whilst
executing an infinite shader on the render ring. As we currently, rearm
the timer with each execbuf, in this scenario the hangcheck will never
fire and we will never detect the lockup on the render ring. Instead,
only arm the timer once per hangcheck, so that hangcheck runs more
frequently.
v2: Rearrange code to avoid triggering a BUG_ON in add_timer from
softirq context.
Testcase: igt/gem_reset_stats/defer-hangcheck*
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86225
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes back to
commit 362b8af7ad
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Thu Jan 30 00:19:38 2014 -0800
drm/i915: Move per ring error state to ring_error
Spotted while reading error states.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Indicate the monitor has been disconnected on disable.
The regression has been introduced in
commit 5fad84a753
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Nov 4 10:30:23 2014 +0200
drm/i915: rewrite hsw/bdw audio codec enable/disable sequences
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86424
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The lack of a break here wasn't for falling through to some other
important code, so made me do a double take. Add a break just to make
things a little less confusing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
kmap never fails.
Spotted-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When invalid cloning configurations were detected during modeset, we
never copied the error code into the return value variable, leading us
to return 0 (success) to userspace.
This regression has been introduced in
commit 50f5275698
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 7 13:11:00 2014 -0800
drm/i915: use compute_config in set_config v4
Testcase: igt/kms_setmode
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86226
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL DPLL0 is used to derive CDCLK but can also be used to drive an
eDP port (as long as we don't want SSC). DPLL0 is special enough to not
be handled by the shared DPLL framework (drives CDCLK, not supposed to
enable the HDMI mode), So we need to compute the configuration
separately from the other DPLLs.
Note that we don't need to reprogram DPLL0 (which would mean bringing
down CDCLK) to support the various eDP 1.3 link rates as they all share
the same VCO (8100).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's document PSR a bit. No functional changes.
v2: Add actual DocBook entry and accept Daniel's improvements.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. Just cleaning and reorganizing it.
v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change. Just making it public for use outside intel_dp.c
Allowing split psr functions.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN6_GT_THREAD_STATUS_REG doesn't seem to exist on VLV. Reads just give
0x0 no matter what the state of the render and media wells.
There was also some hint in the Gunit HAS that thread status not being
needed on VLV, and hence dropped when bringing stuff over from the IVB
design. Not really a definite comment about the specific register itself
though.
Also the w/a itself is no longer listed for VLV in the database. It was
there some time ago in the past, but I guess someone figured out the
mistake and dropped it.
So let's just drop it from the code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading out a DDI config that uses a PLL that is not part of the
shared_dpll scheme (DPLL0), it's totally normal to end up in the
default: case of that switch.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the rps debug messages signficantly recuced by
commit 67956867aa
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Sep 2 15:12:17 2014 +0300
drm/i915: Don't spam dmesg with rps messages on vlv/chv
we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's magic, but it seems to work.
This fixes a regression introduced in
commit 1bb9e632a0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 8 10:02:43 2014 +0200
drm/i915: Only unbind vgacon, not other console drivers
My best guess is that the vga fbdev driver falls over if we rip out
parts of vgacon. Hooray.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82439
Cc: stable@vger.kernel.org (v3.16+)
Reported-and-tested-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts the regressing
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
that causes GPU hangs immediately on boot.
Reported-by: Leo Wolf <jclw@ymail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79996
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: amended the commit message slightly.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On chv the pipe-a power well is the new disp2d well, and it kills pretty
much everything in the display block. So we need to do the the same
dance that vlv does wrt. display irqs and hpd when the power well goes
up or down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OUaP
-----END PGP SIGNATURE-----
Merge tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux into drm-next
drm: Miscellaneous fixes for v3.19-rc1
This is a small collection of fixes that I've been carrying around for a
while now. Many of these have been posted and reviewed or acked. The few
that haven't I deemed too trivial to bother.
* tag 'drm/fixes/for-3.19-rc1' of git://people.freedesktop.org/~tagr/linux:
video/hdmi: Relicense header under MIT license
drm/gma500: mdfld: Reuse video/mipi_display.h
drm: Make drm_mode_create_tv_properties() signature consistent
drm: Implement drm_get_pci_dev() dummy for !PCI
drm/prime: Use unsigned type for number of pages
drm/gem: Fix typo in kerneldoc
drm: Use const data when creating blob properties
drm: Use size_t for blob property sizes
- skl watermarks code (Damien, Vandana, Pradeep)
- reworked audio codec /eld handling code (Jani)
- rework the mmio_flip code to use the vblank evade logic and wait for rendering
using the standard wait_seqno interface (Ander)
- skl forcewake support (Zhe Wang)
- refactor the chv interrupt code to use functions shared with vlv (Ville)
- prep work for different global gtt views (Tvrtko Ursulin)
- precompute the display PLL config before touching hw state (Ander)
- completely reworked panel power sequencer code for chv/vlv (Ville)
- pre work to split the plane update code into a prepare and commit phase
(Gustavo Padovan)
- golden context for skl (Armin Reese)
- as usual tons of fixes and improvements all over
* tag 'drm-intel-next-2014-11-07-fixups' of git://anongit.freedesktop.org/drm-intel: (135 commits)
drm/i915: Use correct pipe config to update pll dividers. V2
drm/i915: Plug memory leak in intel_shared_dpll_start_config()
drm/i915: Update DRIVER_DATE to 20141107
drm/i915: Add gen to the gpu hang ecode
drm/i915: Cache HPLL frequency on VLV/CHV
Revert "drm/i915/vlv: Remove check for Old Ack during forcewake"
drm/i915: Make mmio flip wait for seqno in the work function
drm/i915: Make __wait_seqno non-static and rename to __i915_wait_seqno
drm/i915: Move the .global_resources() hook call into modeset_update_crtc_power_domains()
drm/i915/audio: add DOC comment describing HDA over HDMI/DP
drm/i915: make pipe/port based audio valid accessors easier to use
drm/i915/audio: add audio codec enable debug log for g4x
drm/i915/audio: add audio codec disable on g4x
drm/i915: enable audio codec after port
drm/i915/audio: add vlv/chv/gen5-7 audio codec disable sequence
drm/i915/audio: rewrite vlv/chv and gen 5-7 audio codec enable sequence
drm/i915/skl: Enable Gen9 RC6
drm/i915/skl: Gen9 Forcewake
drm/i915/skl: Log the order in which we flush the pipes in the WM code
drm/i915/skl: Flush the WM configuration
...
Replace the misinformed notes about CHV snoop behaviour with something
that's hopefully closer to reality.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Throw away the hand rolled display irq setup code on chv, and instead
just call vlv_display_irq_postinstall() and vlv_display_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the vlv display irq uninstall code into a separate function, for
eventual sharing with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Running the driver without execlists and hence PPGTT (either aliasing or
full) isn't a supported configuration on gen9+.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_ddi.c:955:41: sparse: constant 8400000000 is so big it is long
intel_ddi.c:955:53: sparse: constant 9000000000 is so big it is long
intel_ddi.c:955:65: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1028:23: sparse: constant 9600000000 is so big it is long
intel_ddi.c:1031:23: sparse: constant 9000000000 is so big it is long
intel_ddi.c:1034:23: sparse: constant 8400000000 is so big it is long
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Given the history, there's some chance we'll keep the same WM code for a
bit (previously, we were able to reuse the same WM code from ILK to BDW,
so that sounds like a fair assumption).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Write and reads following the block changed use engine specific use counters
and unless that is matched here force wake use counting goes bad. Same
force wake is attempted to be taken twice which leads to at least time outs.
NOTE: Depending on feedback from hardware designers it may not be necessary
to grab force wakes on Gen9 here. But for Gen8 it is needed due to a race
between RC6 and ELSP writes.
v2: Added blitter force wake engine and made more future proof.
Added commit note.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LRC increased in size on gen9. Make sure we return the right
size in get_lr_context_size()
v2. Corrected the size, should be 22 pages. I unintentionally mailed out
a test patch w/ size equaling 23 pages.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new AUX port irq bits where needed.
v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moved around on SKL, so we need to make sure we read/write the
correct regs.
v2: fixup WIN_POS offsets (Paulo)
zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.
v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
Don't use BUG() in default:
Use intel_crtc->unpin_work->gtt_offset
(Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The eDP WA to stop link train based on port type is for HSW/BDW, not
required for SKL+.
Suggested by Satheesh
v2: Simplified the check befoe stop_link_train. Suggested by Satheesh.
v3: stop_link_train need not be called from intel_enable_ddi for gen >= 9
Suggested-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: rebase on top of the hw state flattening.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements SKL DPLL programming that includes:
- DPLL allocation
- wide range PLL calculation and programming
- DP link rate programming
- DDI to DPLL mapping
v2: Incorporated following changes
- Added vfunc for function required outside
- Fixed multiple comments in WRPLL calculation
v3: - Fix the DCO computation
- Move the initialization up to not clobber the computed values
- Use the correct macro for DP link rate programming.
- Use wait_for() to wait for the PLL locked bit
v4: Rebase on top of nigthly (Damien)
v5: A few code cleanups in the WRPLL computation (Damien)
- Use uint32_t when possible
- Use abs_diff() in the WRPLL computation
- Make the 64bits divisions use div64_u64()
- Fix typo in dco_central_feq_deviation (freq)
- Replace the chain of breaks with a goto
v6: Port of the patch to work on top of the shared DPLLs (Damien)
v7: Don't try to handle eDP in ddi_pll_select() (Damien)
v8: Modified as per review comments from Paulo (Satheesh)
v9: Rebase on top of Ander's clock computation staging work for atomic (Damien)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake deprecates the usage of PORT_CLK_SEL and we are advised to use
the new DPLL_CRTL2 for the DDI->PLL mapping.
v2: Modified as per review comments
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On skylake, DPLL 1, 2 and 3 can be used for DP and HDMI. The shared dpll
framework allows us to share those DPLLs among DDIs when possible.
The most tricky part is to provide a DPLL state that can be easily
compared. DPLL_CRTL1 is shared by all the DPLLs, 6 bits each. The
per-dpll crtl1 field of the hw state is then normalized to be the same
value if 2 DPLLs do indeed have identical values for those 6 bits.
v2: Port the code to the shared DPLL infrastructure (Damien)
v3: Rebase on top of Ander's clock computation staging work for atomic (Damien)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify the implementation to query DPLL attached to a SKL port.
v2: Rebase on top of the run-time PM on DPMS series (Damien)
v3: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fixup compilation due to the removal of the intel_ddi_dpll_id enum.
And add a fixme about the abuse of pipe_config here.
v3: Rebase on top of the hsw_ddi_clock_get() rename (Damien)
v4: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine programmed cd clock for SKL.
v2: Fix the LCPLL1 enable warning logic
v3: Rebase over the hsw pll rework.
v4: Rebase on top of the per-platform split (Damien)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding structure/enum for SKL clocking implementation.
v2: Addressed Damien's comment
- Removed internal structure from this header file
v3: Stove this into the generic intel_dpll_id enum and give them the established
DPLL_ID_ prefixes. (Daniel)
v4: - We'll only try to share DPLL1/2/3, leaving DPLL0 to eDP
- Use SKL in the skylake shared DPLL names
- Re-add the skl_dpll enum
(Damien)
v5: Remove SKL_DPLL_NONE (Daniel)
v6: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v4,v5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the necessary SKL registers for implementing the
new clocking mechanism.
v2: Addressed review comments by Damien
- Added code comment
- Introduced enum for WRPLL values
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Use 0x, not 0X (Ville)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3,v4)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some machines may have a broken VBT or no VBT at all, but we still want
to use SSC there. So check for it and keep it enabled if we see it
already on. Based on an earlier fix from Kristian.
v2: honor modparam if set too (Daniel)
read out at init time and store for panel_use_ssc() use (Jesse)
v3: trust BIOS configuration over VBT like we do for DP (Jani)
Reported-by: Kristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This has been invalidated in
commit 24f3a8cf77
Author: Akash Goel <akash.goel@intel.com>
Date: Tue Jun 17 10:59:42 2014 +0530
drm/i915: Added write-enable pte bit supportt
But despite that it's in the diff context no one noticed :(
Cc: Akash Goel <akash.goel@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use the same conditions, group by features, add comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is not used within the driver, and merely saving/restoring these
registers isn't going to do any good anyway. In fact, it's possible it's
actively harmful. Any code enabling the feature should handle this
completely in the regular platform specific enable/disable backlight
functions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
AFAICT i9xx_pfit_disable() on the GMCH display crtc disable path in
i9xx_crtc_disable() will always disable the panel fitter by writing 0 to
PFIT_CONTROL. The register save will always save/restore 0. Also we
completely recompue both in intel_gmch_panel_fitting so there's no way
we depend upon leftover bits.
Move the PFIT_CONTROL and PFIT_PGM_RATIOS save/restore to UMS
code. While at it, save/restore them both under the same conditions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Make it a bit clearer that we nowhere depend upon these
bits.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The block was added for spin_lock_irqsave flags, but since the locking
was converted to spin_lock_irq variant, the block is no longer needed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since RSTDBYCTL is only saved on non-KMS path in within i915_save_state,
move the restore in i915_restore_state for symmetry.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't save the panel power sequencer register on vlv/chv for two simple
reasons. First, these are the wrong registers to save to begin
with. Second, they are not restored anyway.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per latest pm guide, we need to do this also on
past hsw.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following the legacy ring submission example, update the
ring->init_context() hook to support the execlist submission mode.
v2: update to use the new workaround macros and cleanup unused code.
This takes care of both bdw and chv workarounds.
v2.1: Add missing call to init_context() during deferred context creation.
v3: Split init_context (emit) in legacy/lrc modes. For lrc, get the ringbuf
from the context (Mika/Daniel).
v4: Merge init_context interfaces back, the legacy mode only needs the ring,
but the lrc mode needs the ring and context (Mika).
Issue: VIZ-4092
Issue: GMIN-3475
Change-Id: Ie3d093b2542ab0e2a44b90460533e2f979788d6c
Cc: Deepak S <deepak.s@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Align function paramater lists properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading a CCK register we should obviously read it from CCK not
Punit. This problem has been present ever since this of code was
introduced in
commit 67c3bf6f55
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 10 13:16:24 2014 +0530
drm/i915: populate mem_freq/cz_clock for chv
The problem was raised during review by Mika [1] but somehow slipped
through the cracks, and the patch got applied with the problem unfixed.
[1] http://lists.freedesktop.org/archives/intel-gfx/2014-July/048937.html
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The predicate source registers are needed to implement conditional
rendering without stalling. The two source registers are used to load
the previous values of the PS_DEPTH_COUNT register saved from
PIPE_CONTROL commands. These can then be compared and used to set the
predicate enable bit via the MI_PREDICATE command.
The command parser version number is increased to 2 to make it easier
to detect the new functionality in user space.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com> (v1)
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This only affects the fastboot path as-is. In that case, we simply need
to make sure that we update the pipe size at the first mode set. Rather
than putting it off until we decide to flip (if indeed we do end up
flipping), update the pipe size as appropriate a bit earlier in the
set_config call.
This sets us up for better pipe tracking in later patches.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these change (e.g. after a modeset following a fastboot), we need to
do a full mode set.
v2:
- put under pipe_config check so we don't deref a null state (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for checking things later.
v2:
- fix hsw infoframe enabled check (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add the missing PIPE_CONF_CHECK_I(has_infoframe); line to the
hw state cross-checker.]
[danet: Squash in fixup from Jesse to correctly compute has_infoframe
in the hdmi compute_config function.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to consult more info before deciding whether to flip
or do a full mode set.
v2:
- don't use uninitialized or incorrect pipe masks in set_config
failure path (Ander)
v3:
- fixup for pipe_config changes in compute_config (Jesse)
v4:
- drop spurious hunk in force restore path (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to calculate the full pipe config before we do any mode
setting work.
v2:
- clarify comments about global vs. per-crtc mode set (Ander)
- clean up unnecessary pipe_config = NULL setting (Ander)
v3:
- fix pipe_config handling (alloc in compute_config, free in set_mode) (Jesse)
- fix arg order in set_mode (Jesse)
- fix failure path of set_config (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the connector would have an encoder but the encoder didn't have a
crtc we might dereference a NULL crtc here. I suppose that should never
happen due to intel_sanitize_encoder(), but let's be a bit paranoid
print a warning if we ever hit this and return INVALID_PIPE to the
caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently objects for which the hardware needs a contiguous physical
address are allocated a shadow backing storage to satisfy the contraint.
This shadow buffer is not wired into the normal obj->pages and so the
physical object is incoherent with accesses via the GPU, GTT and CPU. By
setting up the appropriate scatter-gather table, we can allow userspace
to access the physical object via either a GTT mmaping of or by rendering
into the GEM bo. However, keeping the CPU mmap of the shmemfs backing
storage coherent with the contiguous shadow is not yet possible.
Fortuituously, CPU mmaps of objects requiring physical addresses are not
expected to be coherent anyway.
This allows the physical constraint of the GEM object to be transparent
to userspace and allow it to efficiently render into or update them via
the GTT and GPU.
v2: Fix leak of pci handle spotted by Ville
v3: Remove the now duplicate call to detach_phys_object during free.
v4: Wait for rendering before pwrite. As this patch makes it possible to
render into the phys object, we should make it correct as well!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo noticed that we don't support RPS on GEN9 yet, so WARN for and
ignore any RPS interrupts on that platform.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GEN6 and GEN8 versions differ only in the PM IIR and IER register
addresses and that on GEN8 we need to keep the
GEN8_PMINTR_REDIRECT_TO_NON_DISP PM interrupt unmasked. Abstract away
these 3 things in the GEN6 versions of the helpers and use them
everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous patch the GEN8 RPS handler became very similar to the
GEN6 version, so unify the two functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Move one misplaced hunk from a later patch to fix a bisect
issue as reported by Wu Fengguang's 0-day builder and fix suggested by
Imre.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaDisablePartialInstShootdown:chv and
WaDisableThreadStallDopClockGating:chv are related to the same
register so combine them.
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-WaDisableDopClockGating:chv
-WaDisableSamplerPowerBypass:chv
-WaDisableGunitClockGating:chv
-WaDisableFfDopClockGating:chv
-WaDisableDopClockGating:chv
v2: Remove pre-production WA instead of restricting them
based on revision id (Ville)
For: VIZ-4090
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit "drm/i915: create a prepare phase for sprite plane updates"
changed the old_obj pointer we use when committing sprite planes,
which caused a WARN() and a BUG() to be triggered. Later, commit
"drm/i915: use intel_fb_obj() macros to assign gem objects" introduced
the same problem to function intel_commit_sprite_plane().
Regression introduced by:
commit ec82cb793c9224e0692eed904f43490cf70e8258
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:32 2014 +0100
drm/i915: create a prepare phase for sprite plane updates
and:
commit 77cde95217
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:33 2014 +0100
drm/i915: use intel_fb_obj() macros to assign gem objects
Credits to Imre Deak for pointing out the exact lines that were wrong.
v2: Also fix intel_commit_sprite_plane() (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85634
Testcase: igt/pm_rpm/legacy-planes
Testcase: igt/pm_rpm/legacy-planes-dpms
Testcase: igt/pm_rpm/universal-planes
Testcase: igt/pm_rpm/universal-planes-dpms
Credits-to: Imre Deak <imre.deak@intel.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- ppgtt init/release: these tracepoints are useful for observing the
creation and destruction of Full PPGTTs.
- ctx create/free: we can use the ctx_free trace in combination with the
ppgtt_release one to be sure that the ppgtt doesn't stay alive for too
long after the ctx is destroyed. ctx_create is there for simmetry
- switch_mm: important point in the lifetime of the vm
v4: add DOC information
v5: pull the DOC in drm.tmpl
v6: clean ppgtt init/release traces + add ctx create/free and switch_mm
tracepoints (Chris)
v7: drop execlist_submit_context tracepoint
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Baseline_ELD_Len field does not include ELD Header Block size.
From High Definition Audio Specification, Revision 1.0a:
The header block is a fixed size of 4 bytes. The baseline block
is variable size in multiple of 4 bytes, and its size is defined
in the header block Baseline_ELD_Len field (in number of
DWords).
Do not include the header size in Baseline_ELD_Len field. Fix all known
users of eld[2].
While at it, switch to DIV_ROUND_UP instead of open coding it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
[danvet: Fix compile fail in nouveau.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since a8bb681827 __intel_framebuffer_create() is called
with struct_mutex held, so it should use drm_gem_object_unreference()
instead of drm_gem_object_unreference_unlocked().
Found by Linux Driver Verification project (linuxtesting.org).
This regression has been introduced in
commit a8bb681827
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Feb 10 18:00:39 2014 +0100
drm/i915: Fix error path leak in fbdev fb allocation
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new pipe config values to calculate the updated pll dividers.
This regression was introduced in
commit 0dbdf89f27b17ae1eceed6782c2917f74cbb5d59
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:33 2014 +0200
drm/i915: Add infrastructure for choosing DPLLs before disabling crtcs
and
commit 00d958817dd3daaa452c221387ddaf23d1e4c06f
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:36 2014 +0200
drm/i915: Covert remaining platforms to choose DPLLS before disabling CRTCs
v2: Use intel_pipe_will_have_type() to look at new configuration - Ander
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Creating a blob property will always copy the input data so the data
that is passed in can be const.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The cleanup path would reset pll->new_config to NULL but wouldn't free
the allocated memory.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turned out to be much simpler on top of my latest atomic stuff than
what I've feared. Some details:
- Drop the modeset_lock_all snakeoil in drm_plane_init. Same
justification as for the equivalent change in drm_crtc_init done in
commit d0fa1af40e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Sep 8 09:02:49 2014 +0200
drm: Drop modeset locking from crtc init function
Without these the drm_modeset_lock_init would fall over the exact
same way.
- Since the atomic core code wraps the locking switching it to
per-plane locks was a one-line change.
- For the legacy ioctls add a plane argument to the locking helper so
that we can grab the right plane lock (cursor or primary). Since the
universal cursor plane might not be there, or someone really crazy
might forgoe the primary plane even accept NULL.
- Add some locking WARN_ON to the atomic helpers for good paranoid
measure and to check that it all works out.
Tested on my exynos atomic hackfest with full lockdep checks and ww
backoff injection.
v2: I've forgotten about the load-detect code in i915.
v3: Thierry reported that in latest 3.18-rc vmwgfx doesn't compile any
more due to
commit 21e88620aa
Author: Rob Clark <robdclark@gmail.com>
Date: Thu Oct 30 13:39:04 2014 -0400
drm/vmwgfx: fix lock breakage
Rebased and fix this up.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUX/DqAAoJEHm+PkMAQRiGLtQH/iAt3fRHlYDXjaJian/KG1Cb
wVP0I+HWZmvVmmd0PzyaxCZLgRNwdmmYHEH4QLy2JwZ3jZfFHlxhy+hDWCgz+67t
bIzkLs0Pf1T4kJ2+r8qW2kBEz9PWJHGTQw7NTqZ++Ts3rPptBA6Fg4mEJ6fQigXy
qRIY68DpipUkXV9BWBWijnTmrvP5tt7JtPzBr4DC8frMjvWct8+XwYhc2k2tEv2j
LwLYb1OW6PUpPv2BQBfWjqqH77vYNQVhJwuwGcDe2YZdI0UFkDheL24+RbbPcZ4f
OnrLjJSSgzv6lBWkAaXZK7/WJ/JZbXxEqHzWZQ3xXoQov97bm7lEYJqqi5gDasQ=
=6Qpa
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc4' into drm-next
backmerge to get vmwgfx locking changes into next as the
conflict with per-plane locking.
As obj->map_and_fenceable computation has changed to only be set when
the object is bound inside the global GTT (and is suitable aligned to a
fence region) we need to accommodate those changes when the tiling is
adjusted. The easiest solution is to unbind from the global GTT if we
are currently fenceable, but will not be after the tiling change.
The bug has been exposed by
commit f8fcadba218fe6d23b2e353fea1cf0a4be4c9454
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Oct 31 13:53:52 2014 +0000
drm/i915: Only mark as map-and-fenceable when bound into the GGTT
which tried to fix an oversight from
commit e6a844687c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 11 12:00:12 2014 +0200
drm/i915: Force CPU relocations if not GTT mapped
which changed the handling of obj->map_and_fenceable.
Note that the alignment check is a vestige from our attempts to reduce
the alignment requirements of tiled but unfenced buffers on
gen2/3. Also, that was when unbinding from the GTT meant UC writes and
clflushing, so we went to great pains to avoid such.
That leaves the actual bug of setting map_and_fenceable to true if we're
not bound to ggtt, which violates the change introduced in the above
patch. Unbinding in that case really looks like the simplest and safest
option, we have to do it anyway.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85896
Testcase: igt/gem_concurrent_blit/gttX*
Tested-by: huax.lu@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Valtteri Rantala <valtteri.rantala@intel.com>
[Jani: amend commit message per input from Daniel and bisect result from
Valtteri]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Backmerge drm-next so that I can keep merging patches. Specifically I
want:
- atomic stuff, yay!
- eld parsing patch from Jani.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We need the HPLL frequency when calculating cdclk. Currently we read
that out from the hardware every single time, which isn't going to fly
very well if the device is runtime suspended. So cache the HPLL
frequency in dev_priv and use the cached value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 5cb13c07da.
While the relevance for WaRsDontPollForAckOnClearingFWBits is under
investigation, revert this as regression.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85684
Tested-by: Tested-by: lu hua <huax.lu@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: S, Deepak <deepak.s@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This simplifies the code quite a bit compared to iterating over all
rings during the ring interrupt.
Also, it allows us to drop the mmio_flip spinlock, since the mmio_flip
struct is only accessed in two places. The first is when the flip is
queued and the other when the mmio writes are done. Since a flip cannot
be queued while there is a pending flip, the two paths shouldn't ever
run in parallel. We might need to revisit that if support for replacing
flips is implemented though.
v2: Don't hold dev->struct_mutext while waiting (Chris)
v3: Make the wait uninterruptable (Chris)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that it can be used by the flip code to wait for rendering without
holding any locks.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may need to access various hardware bits in the .global_resources()
hook, so move the call to occur after enabling all the newly required
power wells, but before disabling all the now unneeded wells. This
should guarantee that we have all the sufficient hardware resources
available during the .global_resources() call. And if not, any additional
resources must be explicitly acquired by the .global_resorces() hook.
For instance on VLV/CHV we need to access the gunit mailbox so that we
can talk to punit/cck over sideband. In addition some PFI credit
reprogramming may need to be addes as well, which may require the disp2d
well.
This should also make the power domain refcounts consistent on platforms
which don't have a .global_resource() hook since now they too will
call modeset_update_crtc_power_domains() which will drop the init power.
Previously init power was just left enabled for such platforms.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: include the section in the drm docbook.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This not based on any documentation...
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per spec, and similar to DDI.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for disabling the audio codec on vlv/chv/gen5-7, similar to
hsw/bdw.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the hsw/bdw enable sequence rewrite.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Configure and enable RC6 for Gen9.
v2: Rebase on top of BDW rc6 support (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implement common forcewake functions shared by Gen9 features.
v2: Make the focewake_{get,put} functions static (Mika)
Small coding style fix in the function definition (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.
As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.
v2: Don't wait for pipes that are off
v3: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v4: Rework and document the algorithm after Ville found that it was all
wrong.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.
This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can reduce the indentation level by continuing early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The transition WMs code was doing a shortcut and the values were copied
from the WM0 ones at compute_wm_results() time. Going forward, we want
to compute them like the other WMs and resolve their final register
values in the same way as well.
This patch does just that and isolate the transtion WM compute code in
skl_compute_transition_wm() while skl_compute_wm_results() takes care of
the register values.
We also take the opportunity to disable the transition WMs for now.
We've noticed underruns and they seem to be the culprit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DDB allocation code managed to split in two the compute functions.
Bring back skl_compute_transition_wm() and skl_compute_linetime_wm()
with their little friends.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To align with the ilk WM code and because it makes sense to test against
the upper bounds as soon as possible on variables that are bigger than
the number of bits in the register, let's move the maximum checks from
skl_compute_wm_results() to skl_compute_plane_wm().
v2: Leave the result values to 0 when overflowing the limits (Ville)
Use 32 bits intermediate variables (Damien)
Instead of using the 16 and 8 bits space we have in the result
structure, use 32 bits local variables until we're sure they fit into
the constraints.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What we're talking about here is the DDB allocation (in blocks). That's
more descriptive than 'max_page_buff_alloc'.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville suggested that we should use the same semantics as C arrays to
reduce the number of those pesky +1/-1 in the allocation code.
This patch leaves the debugfs file as is, showing the internal DDB
allocation structure, not the values written in the registers.
v2: Remove the test on ->end in skl_ddb_entry_size() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: minor conflict in i915_debugfs.c
v3: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v4: minor conflict in the i915_debugfs_files array
v5: minor conflict in the i915_debugfs_files array
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the gen >= 9 in the debugfs file condition (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This logically belongs to the WM state, so do it there.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're going to add a new step, let's not hide the copy of the new WM
state inside one inner function, but as a 1st level operation in the WM
update.
v2: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to updated BSpec, If level 1 or any higher level has a value of 0x00,
that level and any higher levels are unused and the associated watermark
registers must not be enabled.
This patch checks for latency 0 for level >=1 and does not enable WM
corresponding to level m | m>=n, if level n (n != 0) has a 0us latency.
v2: Satheesh's review comments
- zero-out latency values (for all higher levels if latency of given
level is zero ) in read_wm_latency() function itself
v3: removed redundant check as per Satheesh's observation.
v4: rebase on top before merging (Damien)
v5: Rebase on top of the default value removal (Ville)
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the updated Bspec, The mailbox response data is not currently
accounting for memory read latency. Add 2 microseconds to the result for
each level.
This patch adds 2us to latency of level 0 for all cases and
for all other levels (1-7) only if latency[level] > 0.
v2: Slightly rework the patch and add a big comment (Damien)
v3: Rebase on top of the renames of the memory latency defines
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: M, Satheeshakrishna <satheeshakrishna.m@intel.com> (v1)
Cc: Lespiau, Damien <damien.lespiau@intel.com>
Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch provides the implementation for reading the pipe wm HW
state.
v2: Incorporated Damien's review comments and also made modifications
to incorporate the plane/cursor split.
v3: No need to ident a line that was fitting 80 chars
Return early instead of indenting the remaining of a function
(Damien)
v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adapt to the planes/cursor split
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fix the 3rd plane/cursor logic (Pradeep Bhat)
v3: Fix one-by-one error in the DDB allocation code
v4: Rebase on top of the skl_pipe_pixel_rate() argument change
v5: Replace the available/start/end output parameters of
skl_ddb_get_pipe_allocation_limits() by a single ddb entry constify
a few arguments
Make nth_active_pipe 0 indexed
Use sizeof(variable) instead of sizeof(type)
(Ville)
v6: Use the for_each_crtc() macro instead of list_for_each_entry()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements the watermark algorithm and its necessary
functions. Two function pointers skl_update_wm and
skl_update_sprite_wm are provided. The skl_update_wm will update
the watermarks for the crtc provided as an argument and then
checks for change in DDB allocation for other active pipes and
recomputes the watermarks for those Pipes and planes as well.
Finally it does the register programming for all dirty pipes.
The trigger of the Watermark double buffer registers will have
to be once the plane configurations are done by the caller.
v2: fixed the divide-by-0 error in the results computation func.
Also reworked the PLANE_WM register values computation func to
make it more compact. Incorporated all other review comments
from Damien.
v3: Changed the skl_compute_plane_wm function to now return success
or failure. Also the result blocks and lines are computed here
instead of in skl_compute_wm_results function.
v4: Adjust skl_ddb_alloc_changed() to the new planes/cursor split
(Damien)
v5: Reworked the affected functions to implement new plane/cursor
split.
v6: Rework the logic that triggers the DDB allocation and WM computation
of skl_update_other_pipe_wm() to not depend on non-computed DDB
values.
Always give a valid cursor_width (at boot it's 0) to keep the
invariant that we consider the cursor plane always enabled.
Otherwise we end up dividing by 0 in skl_compute_plane_wm()
(Damien Lespiau)
v7: Spell out allocation
skl_ddb_ functions should have the ddb as first argument
Make the skl_ddb_alloc_changed() parameters const
(Damien)
v8: Rebase on top of the crtc->primary changes
v9: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v10: Make skl_pipe_pixel_rate() take a pointer to the pipe config
Add a comment about overflow considerations for skl_wm_method1()
Various additions of const
Various use of sizeof(variable) instead of sizeof(type)
Various move of variable definitons to a narrower scope
Zero initialize some stack allocated structures to make sure we
don't have garbage in case we don't write all the values
(Ville)
v11: Remove non-necessary default number of blocks/lines when the plane
is disabled (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now need to allocate space in the DDB for planes being scanned out
ourselves. The data structure to represent an allocation mirrors what
we'll need to write in the registers later on: (start, end).
We add that allocation datat to the skl_wm_values structure as part of
the values to program the hardware with.
v2: Split planes and cursor for consistency.
v3: Make the skl_ddb_entry_size() parameter const
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the structures needed for computation of
watermarks of pipes and planes for SKL.
v2: Incorporated Damien's review comments and removed unused fields
in structs for future features like rotation, drrs and scaling.
The skl_wm_values struct is now made more generic across planes
and cursor planes for all pipes.
v3: implemented the plane/cursor split.
v4: Change the wm union back to a structure (Ville, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines SKL specific PLANE_WM Watermark registers. It also
defines macros to get the addresses of different LP levels within a pipe.
v2: Reworked the register definitions and associated macros to make it more
generic and be able to use for_each_pipe in values computation.
Incorporated Damien's review comments and indentation.
v3: Added default values for lines and blocks. Provided mask for blocks.
v4: Prefix intermedidate (internal-only) macros with _ (Ville)
v5: Remove the lines and block defaults value (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's some serious confusion regarding ELD valid bit that gets set and
cleared back and forth etc. Rewrite it all based on the documented audio
codec enable/disable sequences.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace cares about whether or not swizzling depends on the page
address for its direct access into bound objects. Extend the get_tiling
ioctl to report the physical swizzling value in addition to the logical
swizzling value so that userspace can accurately determine when it is
possible for manual detiling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Testcase: igt/gem_tiled_wc
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always require PIN_GLOBAL when we want a mappable offset (PIN_MAPPABLE).
This causes the pin to fixup the global binding in cases were the vma
was already bound (and due to the proceeding bug, we considered it to be
already mappable).
References: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add WARN_ON to check that PIN_MAP implies PIN_GLOBAL as
discussed on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use the obj->map_and_fenceable hint for when we already have a
valid mapping of this object in the aperture. This hint can only apply
to the GGTT and not to the aliasing-ppGTT. One user of the hint is
execbuffer relocation, which began to fail when it tried to follow the
hint and perform the relocate through the non-existent GGTT mapping.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.
v2: Explain the need for mmio_flip.work in the commit message (Paulo)
Initialize the mmio_flip work in intel_crtc_init() (Paulo)
Prevent new flips the previous flip work finishes (Paulo)
Don't acquire modeset locks for mmio flip work
Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A follow up patch will call this funcion from a work context for the
mmio flip, in which case we cannot acquire the modeset locks. That's
not a problem though, since the check is there to protect vblank and
the mode, but the code that changes that waits for pending flips
first.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that a later patch will use these functions in some other file
and drop the static. Hence the kerneldoc looks appropriate.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add comment that the functions will become non-static
shortly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An earlier commit (c8725f3dc0911d4354315a65150aecd8b7d0d74a: Do not call
retire_requests from wait_for_rendering) removed the use of the ring parameter
within wait_rendering__tail() but did not remove the parameter itself. As the
plan is to remove obj->ring which is where this parameter comes from, it is
simpler to just remove the parameter completely than to update it with a new
source.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch, the RPS sequence for runtime suspend/resume is
exactly like the sequence for S3 suspend/resume:
- flush_delayed_work(&dev_priv->rps.delayed_resume_work)
- intel_runtime_pm_disable_interrupts()
- intel_suspend_gt_powersave()
(suspended)
- intel_runtime_pm_enable_interrupts()
- intel_enable_gt_powersave()
With this, we get rid of WARNs that are currently intermittently
triggered by the system-suspend-execbuf subtest of runtime PM. Notice
that these WARNs could also be triggered in other ways that involved
doing lots of RPM suspend/resume cycles just after a system S3 resume.
Testcase: igt/pm_rpm/system-suspend-execbuf
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the message, not the fault :)
This is what I see:
[ 282.108597] [drm:i915_check_and_clear_faults] Unexpected fault
[ 282.108597] Addr: 0x00000000\n Address space: PPGTT
[ 282.108597] Source ID: 24
[ 282.108597] Type: 0
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are two leftover GTIIR writes in valleyview_irq_preinstall().
Looks like the were originally left behind by:
commit d18ea1b58a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 22:43:25 2013 +0200
drm/i915: unify PM interrupt preinstall sequence
and then the GTIIR reset was added back here:
commit f86f3fb005
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Apr 1 15:37:14 2014 -0300
drm/i915: properly clear IIR at irq_uninstall on Gen5+
so we can kill the leftovers from the vlv code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The extra VLV_IIR writes at the end of vlv_display_irq_postinstall()
serve no purpose. Remove them.
The VLV_IMR/IER/IIR setup at the start of the function also seems a bit
pointless since it doesn't unmask/enable anything. But leave it be for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split the vlv display irq postinstall code to a separate function so
that we can share it with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the vlv display irq reset code to a new functions. The aim is to
share the code with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Genralize valleyview_display_irqs_install() and
valleyview_display_irqs_uninstall() enough so that they work on chv.
The only difference to vlv here being the third pipe that chv brings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like we forgot to call gen5_gt_irq_reset() for vlv in the
uninstall phase. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the hand rolled IIR,IER,IMR disable sequences with
GEN5_IRQ_RESET().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the same ordering rules for the IIR,IER,IMR writes on vlv/chv
that we do on other gen5+ platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like a leftover POSTING_READ(GEN8_PCU_IIR) in
cherryview_irq_preinstall() from some earlier age. GEN5_IRQ_RESET()
already does the posting read so this changes nothing, so kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the hand rolled macros with gen8_gt_irq_reset() and
GEN5_IRQ_RESET() in cherryview_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some has given a name for the DPINVGTT status bitmask, so let's use it
instead of the magic number. Looks more like the chv code now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling interrupts we do the writes in this order:
IMR,IER,IIR,IIR. But when enabling interrupts we don't do use the
mirrored order, and instead do IIR,IIR,IMR,IER.
I like consistency unless there's a good reason against it, which I
can't think of here, so change the enable order to IIR,IIR,IER,IMR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will help future code if this function knows something about of the context
of the display setup object is being pinned for.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Write HWS_PGA address even in execlists mode as the global hardware status
page is still required. This address was previously uninitialized and
HWSP writes would clobber whatever buffer happened to reside at GGTT
address 0.
v2: Break out hardware status page setup into a separate function.
Issue: VIZ-2020
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function was removed in:
commit 037bde19a4
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Mar 27 08:24:19 2014 +0000
Revert "drm/i915: Disable/Enable PM Intrrupts based on the current freq."
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function was removed in:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ddi platforms we don't shut down the link when changing link
training parameters. Except when clock recovery fails too hard and we
restart with channel eq training. Which doesn't make a lot of sense
really, since just stopping/restarting the DP port at this point
violates the modeset sequence documented in the Bspec.
So let's tempt fate and try this.
This patch is motivated by a WARN_ON triggered by
commit bc76e320f2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue May 20 22:46:50 2014 +0200
drm/i915: Drop now misleading DDI comment from dp_link_down
References: https://bugs.freedesktop.org/show_bug.cgi?id=85670
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris removed the code using it in:
commit be2d599b5d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Sep 10 19:52:18 2014 +0100
drm/i915: Remove dead code, i915_gem_verify_gtt
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Paulo said when introducing the enum, having more types is really
good to document what should go where (int foo(int, int, bool, bool).
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's really part of the "push all new_* state into current state
pointers" done in that function. So let's move it there to make this
clear.
Also, with the conversion done the num_shared_dpll check the function
does in it's loop is enough, so we can drop the check for the dpll
compute callback, too.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Now that shared DPLLs configuration is staged, there's no need to track
the current ones in the new pipe_config since those are released before
making the new pipe_config effective.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no users left after the conversion to calculate clocks before
disabling crtcs during mode set.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for a mode set to fail if there aren't shared DPLLS that
match the new configuration requirement or other errors in clock
computation. If that step is executed after disabling crtcs, in the
failure case the hardware configuration is changed and needs to be
restored. Doing those things early will allow the mode set to fail
before actually touching the hardware.
Follow up patches will convert different platforms to use the new
infrastructure.
v2: Keep pll->new_config valid only during mode set (Ville)
Use kmemdup() in i915_shared_dpll_start_config() (Ville)
Restore old pll config if something fails before commit (Ville)
Don't set compute_clock hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new struct will be used in a follow up patch to allow a current and
a staged config to exist for the same shared DPLL.
v2: Rebase on by mask_to_refcount()->hweight32() change. (Damien)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be used in a follow up patch to properly release shared DPLLs
without relying on the shared_dpll field in pipe_config.
v2: Fix white space error (Ville)
Use hweight32() (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More concise. Noticed while reviewing Ander's patch which touched a
lot of the pipe_has_type checks.
v2: Use new_config in one place Ander spotted.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Just various stuff all over from a bunch of people. Shortlog gives a beter
overview, it's really all misc drm patches.
* tag 'topic/core-stuff-2014-11-05' of git://anongit.freedesktop.org/drm-intel:
drm/edid: add #defines and helpers for ELD
drm/dp: Add counters in the drm_dp_aux struct for I2C NACKs and DEFERs
drm: Remove compiler BUG_ON() test
drm: Fix DRM_FORCE_ON_DIGITAL use
drm/gma500: Don't destroy DRM properties in the driver
drm/i915: Don't destroy DRM properties in the driver
drm: Add a note to drm_property_create() about property lifetime
gpu: drm: Fix warning caused by a parameter description in drm_crtc.c
drm/dp-helper: Move the legacy helpers to gma500
drm/crtc: Remove duplicated ioctl code
drm/crtc: Fix two typos
gpu:drm: Fix typo in Documentation/DocBook/drm.xml
gpu: drm: drm_dp_mst_topology.c: Fix improper use of strncat
drm: drm_err: Remove unnecessary __func__ argument
drm: Implement O_NONBLOCK support on /dev/dri/cardN
Never trust (your interpretation of) the VBT. Regression from
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
causing div by zero if VBT minimum brightness equals maximum brightness.
Despite my attempts I've failed in my detective work to figure out what
the root cause is. This is not the real fix, but we have to do
something.
Reported-by: Mike Auty <mike.auty@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=86551
Cc: stable@vger.kernel.org (v3.17+)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During S4 freeze we don't call intel_suspend_complete(), which would
save the gunit HW state, but during S4 thaw/restore events we call
intel_resume_prepare() which restores it, thus ending up in a corrupted
HW state.
Fix this by calling intel_suspend_complete() from the corresponding
freeze_late event handler.
The issue was introduced in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Global GTT doesn't have pat_sel[2:0] so it always point to pat_sel = 000;
So the only way to avoid screen corruptions is setting PAT 0 to Uncached.
MOCS can still be used though. But if userspace is trusting PTE for
cache selection the safest thing to do is to let caches disabled.
BSpec: "For GGTT, there is NO pat_sel[2:0] from the entry,
so RTL will always use the value corresponding to pat_sel = 000"
- System agent ggtt writes (i.e. cpu gtt mmaps) already work before
this patch, i.e. the same uncached + snooping access like on gen6/7
seems to be in effect.
- So this just fixes blitter/render access. Again it looks like it's
not just uncached access, but uncached + snooping. So we can still
hold onto all our assumptions wrt cpu clflushing on LLC machines.
v2: Cleaner patch as suggested by Chris.
v3: Add Daniel's comment
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85576
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Stable@vger.kernel.org
Tested-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This shouldn't change the behavior of those functions, since they are
called after the new_config is made effective and that points to the
current config. In a follow up patch, the mode set sequence will be
changed so this is called before disabling crtcs, and in that case
those functions should work on the staged config.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Flatten if by moving the check into the WARN.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
execlists_submit_context() always returns 0, which is redundant.
And its name is inaccurate, since it actually submits (up to)
TWO contextS. So we rename it, change it to "void", and remove
the WARN_ON() testing its return value.
Change-Id: Ie225b0eca7754c6093c8b8bd15550b251b6feb82
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a ring failed to initialise for any reason then the error path would try to
clean up all rings including those that had not yet been allocated. The ring
clean up code did a check that the ring was valid before starting its work.
Unfortunately, that was after it had already dereferenced the ring to obtain a
dev_private pointer.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When looking at the bug report logs with triggered
WARN_ON, the person doing bug triaging will have to
find exact kernel source and match file/line.
Attach the condition that triggered the WARN_ON
to kernel log. In most cases the context is self
evident and this way we can save developer time.
The drawback is ~16kbytes bigger i915.ko
Signed-off-by: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we suspend we turn everything off so the pps should be idle, and we
also (or at least should) disable all power wells which will reset the
power sequencer port assignment. So when we resume all power sequencers
should be in their reset state. However it's at least theoretically
possible that the BIOS would touch the power seuqencer(s), so to be safe
we ought to read out the current port assignment like we do at driver
init time.
To do that we can simply call vlv_initial_power_sequencer_setup() from
the encoder ->reset() hook before calling intel_edp_panel_vdd_sanitize().
There's no danger or clobbering the pps delays since we now have those
stored within intel_dp and we don't change them once initialized.
This will make sure that the vdd state gets correctly tracked post-resume
in case the BIOS enabled it.
We need to shuffle things around a bit to get the locking right, and
while at it, make intel_edp_panel_vdd_sanitize() static and move it
around a bit to avoid a forward declaration.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pps timestamp initialization was accidentally lost on vlv/chv in
commit a4a5d2f8a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:20 2014 +0300
drm/i915: Track which port is using which pipe's power sequencer
Restore it so that we avoid introducing random delays into the pps operations
during/after driver init time.
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll never end up in the hooks with eld[0] unset, as that's checked by
drm_select_eld().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce functions to enable/disable the audio codec, incorporating the
ELD setup within enable. The disable is initially limited to HSW,
covering exactly what was done previously.
The only functional difference is that ELD valid is no longer set if
there is no connector with ELD, which should be the right thing to do
anyway. Otherwise the sequence remains the same, with warts and all, in
preparation for applying more sanity.
v2: add kernel doc.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The audio programming sequence states that the ELD must be written and
enabled after the pipe is ready. Indeed, this should clarify the
situation with
commit c79057922e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 16 16:56:09 2014 +0200
drm/i915: Remove vblank wait from haswell_write_eld
and Ville's review of it [1].
Moreover, we should not touch the relevant registers before we get the
audio power domain.
[1] http://mid.gmane.org/20140416155309.GK18465@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Keep the driver modifications to ELD together. This also sets the
Conn_Type for G4X DP which wasn't done before.
Clean up the debugs while at it; this is all obvious from the connector
name.
v3: add missing ~ (Rodrigo)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that the pipe-a power well has replaced the disp2d power well
on chv. At least that's the case with the current punit firmware. So
enable the pipe-a power and expand its domains to cover everything the
disp2d well ought to cover.
The other power wells (apart from the cmnlane wells) still seem awol
in the current punit firmware. So leave them disabled in the code.
This fixes a hilarious oops during resume on bsw where
intel_hdmi_get_config() would read the port register and get back
0xffffffff and thus think the port is enabled on pipe D. It would then
go and index the pipe_to_crtc_mapping[] array with PIPE_D and blow up
when intel_hdmi_get_config() tries to write to crtc->config. Someone
really ought to replace all naked pipe_to_crtc_mapping[] uses with the
appropriate function call so we could add a warning there if the pipe
doesn't actually exist...
We must also call the power seqeuencer state reset function from
the pipe-a well disable just like we do from disp2d on vlv. Otherwise
the eDP panel won't recover at resume time since the PPS has lost its
hold on the port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84903
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a programmable CSC unit on the pipe B sprites. Program the unit
appropriately for BT.601 limited range YCbCr to full range RGB color
conversion. This matches the programming we currently do for sprites
on the other pipes and on other platforms.
It seems the CSC only works when the input data is YCbCr. For RGB
pixel formats it doesn't matter what we program into the CSC registers.
Doesn't make much sense to me especially since the register names give
the impression that RGB input data would also work. But that's how
it behaves here.
In the review discussions there's been some nice math to explain the
values obtained here. First about the YCbCr->RGB matrix:
"I had the RGB->YCbCr matrix, inverted it and the values came out. But they
should match the wikipedia article. Also keep in mind that the coefficients
are in .12 in fixed point format, hence we need a 1<<12 factor. So let's
try it:
Kb=.114
Kr=.299
(1<<12) * 255/219 ~= 4769
-(1<<12) * 255/112*(1-Kb)*Kb/(1-Kb-Kr) ~= -1605
-(1<<12) * 255/112*(1-Kr)*Kr/(1-Kb-Kr) ~= -3330
(1<<12) * 255/112*(1-Kr) ~= 6537
(1<<12) * 255/112*(1-Kb) ~= 8263
"Looks like the same values to me."
And then about the limits used for clamping:
"> where did you get these min/max?
"The hardware apparently deals in 10bit values, so we need to multiply everything
by 4 when we start with the 8bit min/max values.
Y = [16:235] * 4 = [64:940]
CbCr = ([16:240] - 128) * 4 = [-112:112] * 4 = [-448:448]
"The -128 being the -0.5 bias that the hardware already applied before
the data entered the CSC unit."
Raw data is also supplied in 10bpc in the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Copypaste explanations&math from the review discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to run intel_uncore_early_sanitize() before we touch any
registers, because on BDW, when we resume, the FPGA_DBG_RM_NOCLAIM bit
is set, so we need to clear it - through intel_uncore_early_sanitize()
- before we do anything else. With the current code, we don't clear
the bit before our first register access, so we print a WARN
complaining about an unclaimed register error.
v1: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume"
v2: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume on non-VLV"
v3: This one, on top of the intel_resume_prepare() rework.
v4: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because, really, the abstraction is not working for us. It is nice for
VLV, but doesn't add anything useful on SNB/HSW/BDW. We want to change
this code due to a recently-discovered bug, but we can't seem to find
a nice solution that repects the current abstraction. So let's kill
intel_resume_prepare() and its friends, and add an equivalent
implementation to both its callers.
Also, look at the diffstat!
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV adds a bunch of new registers for primary plane size/position and
pipe blender setup. Initialize all those registers to avoid nasty
surprises. PRIMSIZE is especially important as without programming it
the outout will be garbled whenever the primary plane size would not
match what the BIOS set up.
Also program the sprite constant alpha register to disable the constant
alpha blending factor. This applies to vlv as well as chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case the cmnlane power well is down but cmnreset isn't asserted we
would currently skip the off+on toggle for the power well. That could
leave cmnreset deasserted while cmnlane is powered down which might
lead to problems with the PHY.
To avoid such issues skip the cmnlane toggle only if both cmnlane and
disp2d wells are up and cmnreset is already deasserted. In all other
cases power down the cmnlane well which will also make sure cmnreset
gets asserted correctly while cmnlane is powered down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the macros makes the code cleaner and it also checks for a NULL fb.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
take out pin_fb code so the commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Take out the pin_fb code so commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power seqeuencer kick procedure requires the DPLL to be running
in order to complete successfully. In case the DPLL isn't currently
running when we need to kick the power seqeuncer enable it
temporarily. This can happen eg. during ->detect() when the pipe is
not already active.
To avoid needlessly duplicating the DPLL programming re-use the already
existing functions by passing a temporary pipe config to them instead
of having them consult the current pipe config at crtc->config.
v2: Introduce vlv_force_pll_{on,off}() (Daniel)
v3: Rebase due to drm_crtc vs. intel_crtc changes
Fix a typo in commit msg (checkpatch)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP ports need the power seqeuncer whenever the port is active. Warn if
we accidentally steal the power sequener from an active eDP port. This
should not happen unless there's a bug somewhere else, but it's best to
scream loudly if it happens to help with debugging.
Note that this only checks for active pipes and not for enabled pipes
which are turned off with dpms. Which means we might run the risk that
the pps might get stolen and we can't reacquire one when enabling the
pipe again with dpms on. But on current platforms that's impossible
since we only support two edp ports with just two panel power
sequencers. So a more elaborate scheme which reserves the pps even
when the pipe is inactive isn't required.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Summarize my discussion with Ville about dpms on/off issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should never enable the panel power twice. That would indicate a bug
somewhere else as we would need to enable the port twice without
disabling it in between. Also print the port name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print the port name in the VDD/PPS debugs messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we fumble something and end up picking an already used power
seqeuencer in vlv_power_sequencer_pipe() at least try to steal it
gracefully. In theory this should never happen though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no power sequencer on pipe C on VLV/CHV so scream a bit if we
try to steal one from pipes other than A and B.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV gets confused if two power sequencers have the same port selected.
It would seem the port doesn't start up properly in the is case and
vlv_wait_port_ready() will fail as will the link training. Clearing the
port select in the PP_ON_DELAYS register fixes this problem.
CHV doesn't seem to need this, but it doesn't seem to hurt either so
let's just do it for both to keep the code between the platforms as
uniform as possible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If there's no power sequencer assigned to the port currently we can't
very well have vdd or panel power enabled either. If we would try to
check that from the pps registers we'd need to pick a power seqeuncer
and kick it. So let's skip the register read and the kick.
Note that there's still a bit an issue about correctly recovering pps
state from resume if the bios is nasty: With this check we'll always
assume that the pps is off. But that's better done in a follow-up
patch and it shouldn't be too harmful - at most we waste time enabling
the pps if it's on already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about resume issues Imre spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we pick a new power sequencer for the port but we're not doing a
full modeset, the power sequencer may have locked on to another port (or
no port). So kick it a bit to make sure it controls the port we want.
Again just like when we attempt to actually enable the DP port, we
must first write the port register with the approriate value except
the enable bit, and then we must enable the port to make the power
sequencer happy. In this case since we don't want the port actually
enabled we just toggle it on and immediately back off. Going forward
the power sequencer will keep working on that specific port until again
moved to another port.
v2: Refine the kick procedure
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When switching from one pipe to another, the power sequencer of the new
pipe seems to need a bit of kicking to lock into the port. Even the vdd
force bit doesn't work before the power sequencer has been sufficiently
kicked, so this must be done before any AUX transactions are attempted.
After extensive experimentation I've determined that it's sufficient
to first write the port register with the correct values except the
port must remain disabled, then we can do a second write to enable the
port, after which the power sequencer is operational and allows the port
to start up properly.
Contrary to my earlier theories we don't need to enable the port with
the idle pattern, so let's just use training pattern 1 as that's what
other platforms use here.
v2: Refine the kick procedure
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no point in checking if the data lanes came out of reset after
link training. If the data lanes aren't ready link training will fail
anyway.
Suggested-by: Todd Previte <tprevite@gmail.com>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just grab the pps_mutex once and do all the pps panel startup operations
while holding the mutex instead of grabbing the mutex separately for
each individual step.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll be needing to the call the power seqeuencer functions while
already holding pps_mutex, so split the locking out to small wrapper
functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we read the current power seqeuncer delays from the registers
(as well as looking at the vbt and spec values) we may end up
corrupting delays we already initialized when we switch to another
pipe and the power seqeuncer there has different values currently
in the registers.
So make sure we only initialize the delays once even if
intel_dp_init_panel_power_sequencer() gets called multiple times.
There was some discussion in the review about when exactly we need to
unlock the pps. Quoting Bspec:
"If this bit is not a zero, it activates the register write protect
and writes to those registers will be ignored unless the write
protect key value is set in the panel sequencing control register."
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add Bspec quote per review discussion between Imre and
Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power seqeuncer delays are fixed for a given panel, so we can keep
them around once computed.
Not that on VLV/CHV we still re-compute them every time we initialize
the power seqeuncer registers, but that will change soon enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
want_panel_vdd is a bool so it can't cope with interleaving on/off calls
from multiple threads. If we want to make that possible we'd need to
convert want_panel_vdd into a proper ref count. But an easier fix is to
remove the high level vdd on/off calls from detect/hpd code paths and
just rely on the delayed vdd off to avoid needless vdd on<->off ping
pong.
After this change only the encoder enable/disable paths use the high
level functions, which is fine since both the on and off low level edp
vdd calls from intel_dp_aux_ch() happen without dropping pps_mutex in
between and so want_panel_vdd can't change in between.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only ports B and C have the power sequencer and backlight controls,
so complain if we ever try to register an eDP connector on some other
port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because I got annoyed that I had to document what values "int
ddi_personality" is supposed to hold.
A good side-effect of this change is that now the compilers can do
some additional checks on our code, which may prevent some bugs in the
future. A bad side-effect of this change is that now the compilers do
some additional checks on our code and complain when a switch
statement doesn't check for all possible values, so we need to add
"default" cases to all those switches. Hopefully, this may help
preventing confusions against DRM_MODE_CONNECTOR_* and
DRM_MODE_ENCODER_*.
I guess that just by looking at the patch, some people will think this
change is not worth its benefits. In this case, I don't really mind
dropping the patch.
Also, there's probably still a few more places where we can
s/int/enum intel_output_type/, but we can change that later, when we
spot the places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Resolve conflict due to reordered patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will simplify things later on. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everything else can be derived from that. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most importantly, "i" need not be the universal variable used for
everything. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Const is good.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for some additional cleanup. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The fb check introduced to drm_plane_helper_check_update() just make this
check impossible to branch in.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
use_mmio_flip() makes sure we only enable MMIO flips on gen5+. So we
don't need to take into account older devices.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no point in flipping a buffer for a disabled crtc.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch includes the Gen9 batch buffer to generate
a 'golden context' for that product family.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The file drivers/gpu/drm/i915/intel_renderstate_gen8.c is
updated to the version created by IGT null_state_gen
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
libva uses chained batch buffers in a way that the command parser
can't generally handle. Fortunately, libva doesn't need to write
registers from batch buffers in the way that mesa does, so this
patch causes the driver to fall back to non-secure dispatch if
the parser detects a chained batch buffer.
Note: The 2nd hunk to munge the error code of the parser looks a bit
superflous. At least until we have the batch copy code ready and can
run the cmd parser in granting mode. But it isn't since we still need
to let existing libva buffers pass (though not with elevated privs
ofc!).
Testcase: igt/gem_exec_parse/chained-batch
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Add note - this confused me in review and Brad clarified
things (after a few mails ...).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the cursor plane to be updated the same way as primary and sprites,
and same set_property handler is used for all of these planes.
v2 (by Matt Roper): Rework to apply to latest di-nightly codebase. The
switch to split check/commit plane programming changed the code
flow enough that the original patch could no longer be applied.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these flags are on the object level it will be more difficult to allow
for multiple VMAs per object.
v2: Simplification and cleanup after code review comments (Chris Wilson).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- suspend/resume/freeze/thaw unification from Imre
- wa list improvements from Mika&Arun
- display pll precomputation from Ander Conselvan, this removed the last
->mode_set callbacks, a big step towards implementing atomic modesets
- more kerneldoc for the interrupt code
- 180 rotation for cursors (Ville&Sonika)
- ULT/ULX feature check macros cleaned up thanks to Damien
- piles and piles of fixes all over, bug team seems to work!
* tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20141024
drm/i915: add comments on what stage a given PM handler is called
drm/i915: unify switcheroo and legacy suspend/resume handlers
drm/i915: add poweroff_late handler
drm/i915: sanitize suspend/resume helper function names
drm/i915: unify S3 and S4 suspend/resume handlers
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
drm/i915: enable output polling during S4 thaw
drm/i915: check for GT faults in all resume handlers and driver load time
drm/i915: remove unused restore_gtt_mappings optimization during suspend
drm/i915: fix S4 suspend while switcheroo state is off
drm/i915: vlv: fix switcheroo/legacy suspend/resume
drm/i915: propagate error from legacy resume handler
drm/i915: unify legacy S3 suspend and S4 freeze handlers
drm/i915: factor out i915_drm_suspend_late
drm/i915: Emit even number of dwords when emitting LRIs
drm/i915: Add rotation support for cursor plane (v5)
drm/i915: Correctly reject invalid flags for wait_ioctl
drm/i915: use macros to assign mmio access functions
drm/i915: only run hsw_power_well_post_enable when really needed
...
When drm properties are created, they are added to mode_config.property_list,
which is then used in drm_mode_config_cleanup() to destroy every single
property created by the driver.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ivybridge + 30" monitor prints a drm error on every modeset, since IVB
doesn't support DP3 we should even bother trying to use it.
This regression has been introduced in
commit 06ea66b6bb
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable
devices
Reported-by: Dave Airlie <airlied@redhat.com>
Reference: http://mid.gmane.org/1414566170-9868-1-git-send-email-airlied@gmail.com
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
prevents backlight setup on Macbook 2,1. Apply quirk to ignore the VBT
check so backlight is set up properly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81438
Signed-off-by: Jens Stein Jørgensen <jens.s.stein@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ok, new attempt, this time around with full ppgtt disabled again.
drm-intel-next-2014-10-03:
- first batch of skl stage 1 enabling
- fixes from Rodrigo to the PSR, fbc and sink crc code
- kerneldoc for the frontbuffer tracking code, runtime pm code and the basic
interrupt enable/disable functions
- smaller stuff all over
drm-intel-next-2014-09-19:
- bunch more i830M fixes from Ville
- full ppgtt now again enabled by default
- more ppgtt fixes from Michel Thierry and Chris Wilson
- plane config work from Gustavo Padovan
- spinlock clarifications
- piles of smaller improvements all over, as usual
* tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel: (114 commits)
Revert "drm/i915: Enable full PPGTT on gen7"
drm/i915: Update DRIVER_DATE to 20141003
drm/i915: Remove the duplicated logic between the two shrink phases
drm/i915: kerneldoc for interrupt enable/disable functions
drm/i915: Use dev_priv instead of dev in irq setup functions
drm/i915: s/pm._irqs_disabled/pm.irqs_enabled/
drm/i915: Clear TX FIFO reset master override bits on chv
drm/i915: Make sure hardware uses the correct swing margin/deemph bits on chv
drm/i915: make sink_crc return -EIO on aux read/write failure
drm/i915: Constify send buffer for intel_dp_aux_ch
drm/i915: De-magic the PSR AUX message
drm/i915: Reinstate error level message for non-simulated gpu hangs
drm/i915: Kerneldoc for intel_runtime_pm.c
drm/i915: Call runtime_pm_disable directly
drm/i915: Move intel_display_set_init_power to intel_runtime_pm.c
drm/i915: Bikeshed rpm functions name a bit.
drm/i915: Extract intel_runtime_pm.c
drm/i915: Remove intel_modeset_suspend_hw
drm/i915: spelling fixes for frontbuffer tracking kerneldoc
drm/i915: Tighting frontbuffer tracking around flips
...
vlv_cdclk_freq is in kHz but we need MHz for the GMBUSFREQ divider.
This is a regression from:
commit f8bf63fdcb
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jun 13 13:37:54 2014 +0300
drm/i915: Kill duplicated cdclk readout code from i2c
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Turning vdd on/off can generate a long hpd pulse on eDP ports. In order
to handle hpd we would need to turn on vdd to perform aux transfers.
This would lead to an endless cycle of
"vdd off -> long hpd -> vdd on -> detect -> vdd off -> ..."
So ignore long hpd pulses on eDP ports. eDP panels should be physically
tied to the machine anyway so they should not actually disappear and
thus don't need long hpd handling. Short hpds are still needed for link
re-train and whatnot so we can't just turn off the hpd interrupt
entirely for eDP ports. Perhaps we could turn it off whenever the panel
is disabled, but just ignoring the long hpd seems sufficient.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Sometimes we seem to get utter garbage from DPCD reads. The resulting
buffer is filled with the same byte, and the operation completed without
errors. My HP ZR24w monitor seems particularly susceptible to this
problem once it's gone into a sleep mode.
The issue seems to happen only for the first AUX message that wakes the
sink up. But as the first AUX read we often do is the DPCD receiver
cap it does wreak a bit of havoc with subsequent link training etc. when
the receiver cap bw/lane/etc. information is garbage.
A sufficient workaround seems to be to perform a single byte dummy read
before reading the actual data. I suppose that just wakes up the sink
sufficiently and we can just throw away the returned data in case it's
crap. DP_DPCD_REV seems like a sufficiently safe location to read here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This will hopefully make it easier to navigate the code without the need
to consult the full PM documentation.
v2:
- add a comment that the freeze handler is also called after rebooting
- add a comment that the thaw handler is also called to recover from
errors (Ville)
- add the PM event names (PMSG_THAW etc.) for reference (Ville)
- add comments that s0ix can be handled both via system and runtime
suspend (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By now we handle switcheroo and legacy suspend/resume the same way, so
no need to keep separate functions for them.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The suspend_late handler saves some registers and powers off the device,
so it doesn't have a big overhead. Calling it at S4 poweroff_late time
makes the power off handling identical to the S3 suspend and S4 freeze
handling, so do this for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By now the S4 freeze/thaw and S3 suspend/resume events are handled the
same way, so we can rename the freeze/thaw internal helpers to
suspend/resume accordingly to make clearer what the helpers do. Also
rename i915_resume_early to i915_drm_resume_early aligning it with the
rest of the helper names.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The S3 and S4 events are now handled the same way internally, there is no
need to keep separate wrapper functions around them. Simply reuse the
suspend/resume versions everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already disable everything during S4 freeze, except the PCI device
itself. There is no reason why we couldn't disable that too and doing
so allows us to unify these handlers in the next patch with the
corresponding S3 suspend/resume handlers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid processing hotplug events we disable connector polling for the
duration of S3 suspend. We also disable it for S4 freeze, and keep it
disabled after S4 thaw. This won't prevent though hotplug processing,
since we re-enable interrupts anyway. There is also no need to prevent
it at that time, since we reinitialize everything during thaw, so the
device is in a consistent state. So to simplify things enable polling
during thaw, which will allow us to handle S4 thaw the same way as S3
resume in an upcoming patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking for GT faults is not specific in any way to S4 thaw, so do it
also during S3 resume, S4 restore and driver load time. This allows us to
unify the Sx handlers in an upcoming patch.
v2:
- move the check to intel_uncore_early_sanitize(), so we check at driver
load time too (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logic to skip restoring GTT mappings was added to speed up
suspend/resume, but not on old GENs where not restoring them caused
problems. The check for old GENs is based on the existence of OpRegion,
but this doesn't work since opregion is initialized only after
the check. So we end up always restoring the mappings.
On my BYT - which has OpRegion - skipping restoring the mappings during
suspend doesn't work, I get a GPU hang after resume. Also the logic of
when to allow the optimization during S4 is reversed: we should allow it
during S4 thaw but not during S4 restore, but atm we have it the other
way around in the code.
Since correctness wins over optimal code and since the optimization
wasn't used anyway I decided not to try to fix it at this point, but
just remove it. This allows us to unify the S3 and S4 handlers in the
following patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the device is suspended already through the switcheroo interface we
shouldn't suspend it again or resume it after suspend. We have the
corresponding check for S3 suspend already, add it for all the other
S3 and S4 handlers. Also move the check from i915_resume_early() to
i915_resume_legacy(), so that it's done in the high level handler for
all PM events.
v2:
- fix the resume path too, we don't need to special case there
DRM_SWITCH_POWER_OFF with the device being enabled (in which case we'd
have to disable the device), since that never happens (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During switcheroo/legacy suspend we don't call the suspend_late handler
but when resuming afterwards we call resume_early. This happened to work
so far, since suspend_late only disabled the PCI device. This changed in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
drm/i915: Sharing platform specific sequence between runtime and system susp
after which we also saved/restored the VLV Gunit HW state in
suspend_late/resume_early. So now since we don't save the state during
suspend a following resume will restore a corrupted state.
Fix this by calling the suspend_late handler during both switcheroo and
legacy suspend.
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_suspend() is called from the DRM legacy S3 suspend/S4 freeze paths
and the switcheroo suspend path. For switcheroo we only ever need to
perform a full suspend (PM_EVENT_SUSPEND) and for the DRM legacy path
we can handle the S4 freeze (PM_EVENT_FREEZE) the same way as S3
suspend. The only difference atm between suspend and freeze is that
during freeze we don't disable the PCI device, but there is no reason
why we can't do so. So unify the two cases to reduce complexity.
Note that for the DRM legacy case the thaw event is not handled, so
we disable the display before creating the hibernation image and it
won't get re-enabled until reboot. We could fix this leaving the
display enabled for the image creation/writing (if we care enough
about UMS), but this can be done as a follow-up.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch fixing the switcheroo/legacy suspend
paths.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The number of DWords should be even when doing ring emits as
command sequences require QWord alignment.
There was some discussion about the maximum length of the MI_LRI
command. Quoting Mika
"I did some test with bdw:
"The maximum is 128 writes, resulting the 8 bit length
field of the command being 0xff, thus following the spec.
The 128'th write went through.
"Perhaps the max command length is then less in older gens?
"Perhaps WARN_ON(x > 128) in MI_LOAD_REGISTER_IMM would be in place
but one needs minor tweak to command parser a bit also then.
#define I915_MAX_WA_REGS 16
keeps us safe for now atleast."
Ville commented that on pre-gen6 the length field seems to be
restricted to 0x3f though. So for all cases we should be ok.
v2: user LRI variant that can write multiple regs in one go (Damien).
We can simply insert one NOP at the end instead of one per register write.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add a summary of the MI_LRI length discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor plane also supports 180 degree rotation. Add a new
"cursor-rotation" property on the crtc which controls this.
Unlike sprites, the cursor has a fixed size, so if you have a small
cursor image with the rest of the bo filled by transparent pixels,
simply flipping the rotation property will cause the visible part
of the cursor to shift. This is something to keep in mind when
using cursor rotation.
v2: Fix gen4/vlv by offsetting the base address appropriately
v3: Removing cursor-rotation property and using rotation property on cursor
plane.
v4: Changing the author name back to Ville.
v5 (by Matt Roper): Slight tweaking to apply against latest di-nightly
codebase.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not having checks for this isn't good.
I've checked igt and libdrm and they all already clear flags properly.
So we're lucky and should be able to sneak this ABI clarification in.
Testcase: igt/gem_wait/invalid-flags
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85280
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is beautification prep work since vgt will add even more special
cases. With these macros it's much easier to see what's going on
really.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
[danvet: #undef the temporary macros after the function again. And
write a commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only run it after we actually enable the power well. When we're
booting the machine there are cases where we run
hsw_power_well_post_enable without really needing, and even though
this is not causing any real bugs, it is unneeded and causes confusion
to people debugging interrupts.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current chv spec teels we can only use either 16 or 32 bits as precision.
Although in the past VLV went from 16/32 to 32/64 and spec might not be updated,
these precision values brings stability and fixes some issues Wayne was facing.
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Wayne Boyer <wayne.boyer@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Sprinkle const as requested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The indirection here seems to serve no purpose. Probably leftovers
from earlier revisions. Spotted while trying to review some mst
patches.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Otherwise we will get WARNs when we read context status registers and
the machine is suspended.
Testcase: igt/pm_rpm/debugfs-read
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I managed to fumble the per spline PCS DW11 register defines in:
commit 570e2a747b
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 18 14:42:46 2014 +0300
drm/i915: Clear TX FIFO reset master override bits on chv
Fortunately the bit in DW0 that was cleared due to this didn't have
any effect as long as the bit we meant to clear was already zero.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix commit ref as pointed out by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_crt_reset() resets the ADPA register on all gen5+ platforms.
However the debug message claims it's touching the PCH ADPA register
which is clearly not what it does on VLV. Drop the PCH part from
the debug message.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some yet-undiscovered reason, when IPS gets enabled, the pipe CRC
changes. Since hsw_enable_ips() doesn't really guarantees to enable
IPS (it depends on package C-states), we can't really predict if IPS
is enabled or disabled while running our CRC tests, so let's just
completely disable IPS while pipe CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch. While this doesn't happen,
let's merge this patch, so every IGT test relying on the CRCs can
work on pipe A.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72864
Testcase: igt/kms_cursor_crc (and others)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In its current place, it just segfaults while trying to access the
CRTC structures:
[ 9132.421681] Call Trace:
[ 9132.421707] [<ffffffffa01130d8>] i915_get_crtc_scanoutpos+0x1e8/0x220 [i915]
[ 9132.421727] [<ffffffffa001da34>] drm_calc_vbltimestamp_from_scanoutpos+0x94/0x330 [drm]
[ 9132.421744] [<ffffffffa001d240>] ?vblank_disable_and_save+0x40/0x1e0 [drm]
[ 9132.421769] [<ffffffffa0114328>] i915_get_vblank_timestamp+0x68/0xb0 [i915]
[ 9132.421786] [<ffffffffa001d094>] drm_get_last_vbltimestamp+0x44/0x80 [drm]
[ 9132.421801] [<ffffffffa001d3a6>] vblank_disable_and_save+0x1a6/0x1e0 [drm]
[ 9132.421817] [<ffffffffa001eac1>] drm_vblank_cleanup+0x61/0xa0 [drm]
[ 9132.421849] [<ffffffffa0177a5e>] i915_driver_unload+0xde/0x290 [i915]
[ 9132.421867] [<ffffffffa0020264>] drm_dev_unregister+0x24/0xb0 [drm]
[ 9132.421884] [<ffffffffa002090e>] drm_put_dev+0x1e/0x70 [drm]
[ 9132.421901] [<ffffffffa00e01e0>] i915_pci_remove+0x10/0x20 [i915]
[ 9132.421910] [<ffffffff81347556>] pci_device_remove+0x36/0xb0
[ 9132.421920] [<ffffffff8140084a>] __device_release_driver+0x7a/0xf0
[ 9132.421928] [<ffffffff81400fc8>] driver_detach+0xb8/0xc0
[ 9132.421936] [<ffffffff8140054a>] bus_remove_driver+0x4a/0xb0
[ 9132.421944] [<ffffffff81401717>] driver_unregister+0x27/0x50
[ 9132.421953] [<ffffffff81346f65>] pci_unregister_driver+0x25/0x70
[ 9132.421971] [<ffffffffa00229c8>] drm_pci_exit+0x78/0xa0 [drm]
[ 9132.422000] [<ffffffffa017a6d2>] i915_exit+0x20/0x94e [i915]
[ 9132.422009] [<ffffffff810fb9dc>] SyS_delete_module+0x13c/0x1f0
[ 9132.422019] [<ffffffff8131c5fb>] ?
trace_hardirqs_on_thunk+0x3a/0x3f
[ 9132.422028] [<ffffffff816f7792>] system_call_fastpath+0x16/0x1b
This means it has to be before intel_modeset_cleanup, which cleans the
CRTC structures. But if we move it to before intel_fbdev_fini(), we
get WARNs because intel_fbdev_fini() still tries to use the vblanks,
so the only acceptable point for drm_vblank_cleanup() seems to be this
place.
Related commit:
commit cbb47d179f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Sep 23 17:33:20 2013 -0300
drm/i915: Add some missing steps to i915_driver_load error path
Testsuite: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77511
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83484
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SPT is always in the PCH override mode, and the bit MBZ. Only set
override on LPT.
v2: check for PCH version (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some machines (like MBAs) might use a tiled framebuffer but not enable
display swizzling at boot time. We want to preserve that configuration
if possible to prevent a boot time mode set. On IVB+ it shouldn't
affect performance anyway since the memory controller does internal
swizzling anyway.
For most other configs we'll be able to enable swizzling at boot time,
since the initial framebuffer won't be tiled, thus we won't see any
corruption when we enable it.
v2: preserve swizzling if BIOS had it set (Daniel)
v3: preserve swizzling only if we inherited a tiled framebuffer (Daniel)
check display swizzle setting in detect_bit_6_swizzle (Daniel)
use gen6 as cutoff point (Daniel)
v4: fixup swizzle preserve again, had wrong init order (Daniel)
Reported-by: Kristian Høgsberg <hoegsberg@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During S4 freeze we don't call intel_suspend_complete(), which would
save the gunit HW state, but during S4 thaw/restore events we call
intel_resume_prepare() which restores it, thus ending up in a corrupted
HW state.
Fix this by calling intel_suspend_complete() from the corresponding
freeze_late event handler.
The issue was introduced in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the workaround list has the value as initialization time
constant, we can do the simple checking on the go without
negleting igt.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we build the workaround list in ring initialization
and decouple it from the actual writing of values, we
gain the ability to decide where and how we want to apply
the values.
The advantage of this will become more clear when
we need to initialize workarounds on older gens where
it is not possible to write all the registers through ring
LRIs.
v2: rebase on newest bdw workarounds
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Resolve tiny conflict in comments and ocd alignments a bit.]
[danvet2: Remove bogus force_wake_get call spotted by Paulo and QA.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The whole file is only built with CONFIG_COMPAT=y.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The legacy DRM suspend logic (effective in UMS) doesn't handle any S4 thaw
events so we don't need to care about it either. Only S3 suspend and S4
freeze events are handled. Leave an assert behind to be sure.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For consistency, since that's the rule followed for internal functions.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak