Extend the hip04_eth driver to support HI13X1_GMAC.
Enable it with CONFIG_HI13X1_GMAC option.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Biao Huang says:
====================
stmmac: fix out-of-boundary issue and add taller hash table support
Fix mac address out-of-boundary issue in net-next tree.
and resend the patch which was discussed in
https://lore.kernel.org/patchwork/patch/1082117
but with no further progress.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1. get hash table size in hw feature reigster, and add support
for taller hash table(128/256) in dwmac4.
2. only clear GMAC_PACKET_FILTER bits used in this function,
to avoid side effect to functions of other bits.
stmmac selftests output log with flow control on:
ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address array size is GMAC_MAX_PERFECT_ADDRESSES,
so the 'reg' should be less than it, or will affect other registers.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates says:
====================
tc-testing: Add plugin for simple traffic generation
This series supersedes the previous submission that included a patch for test
case verification using JSON output. It adds a new tdc plugin, scapyPlugin, as
a way to send traffic to test tc filters and actions.
The first patch makes a change to the TdcPlugin module that will allow tdc
plugins to examine the test case currently being executed, so plugins can
play a more active role in testing by accepting information or commands from
the test case. This is required for scapyPlugin to work.
The second patch adds scapyPlugin itself, and an example test case file to
demonstrate how the scapy block works in the test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The scapyPlugin allows for simple traffic generation in tdc to
test various tc features. It was tested with scapy v2.4.2, but
should work with any successive version.
In order to use the plugin's functionality, scapy must be
installed. This can be done with:
pip3 install scapy
or to install 2.4.2:
pip3 install scapy==2.4.2
If the plugin is unable to import the scapy module, it will
terminate the tdc run.
The plugin makes use of a new key in the test case data, 'scapy'.
This block contains three other elements: 'iface', 'count', and
'packet':
"scapy": {
"iface": "$DEV0",
"count": 1,
"packet": "Ether(type=0x800)/IP(src='16.61.16.61')/ICMP()"
},
* iface is the name of the device on the host machine from which
the packet(s) will be sent. Values contained within tdc_config.py's
NAMES dict can be used here - this is useful if paired with
nsPlugin
* count is the number of copies of this packet to be sent
* packet is a string detailing the different layers of the packet
to be sent. If a property isn't explicitly set, scapy will set
default values for you.
Layers in the packet info are separated by slashes. For info about
common TCP and IP properties, see:
https://blogs.sans.org/pen-testing/files/2016/04/ScapyCheatSheet_v0.2.pdf
Caution is advised when running tests using the scapy functionality,
since the plugin blindly sends the packet as defined in the test case
data.
See creating-testcases/scapy-example.json for sample test cases;
the first test is intended to pass while the second is intended to
fail.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of only passing the test case name and ID, pass the
entire current test case down to the plugins. This change
allows plugins to start accepting commands and directives
from the test cases themselves, for greater flexibility
in testing.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The restructuring of the driver got the dependencies wrong: without
CONFIG_NET_DSA we get this build failure:
WARNING: unmet direct dependencies detected for NET_DSA_VITESSE_VSC73XX
Depends on [n]: NETDEVICES [=y] && HAVE_NET_DSA [=y] && OF [=y] && NET_DSA [=n]
Selected by [m]:
- NET_DSA_VITESSE_VSC73XX_PLATFORM [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && HAS_IOMEM [=y]
ERROR: "dsa_unregister_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_switch_alloc" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_register_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
Add the appropriate dependencies.
Fixes: 95711cd5f0 ("net: dsa: vsc73xx: Split vsc73xx driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josua Mayer says:
====================
Fix hang of Armada 8040 SoC in orion-mdio
With a modular kernel as configured by Debian a hang was observed with
the Armada 8040 SoC in the Clearfog GT and Macchiatobin boards.
The 8040 SoC actually requires four clocks to be enabled for the mdio
interface to function. All 4 clocks are already specified in
armada-cp110.dtsi. It has however been missed that the orion-mdio driver
only supports enabling up to three clocks.
This patch-set allows the orion-mdio driver to handle four clocks and
adds a warning when more clocks are specified to prevent this particular
oversight in the future.
Changes since v1:
- fixed condition for priting the warning (Andrew Lunn)
- rephrased commit description for deferred probing (Andrew Lunn)
- fixed compiler warnings (kbuild test robot)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a warning when device tree specifies more than the maximum of four
clocks supported by orion-mdio. Because reading from mdio can lock up
the Armada 8k when a required clock is not initialized, it is important
to notify the user when a specified clock is ignored.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to four clocks to be specified and enabled for the orion-mdio
interface, which are required by the Armada 8k and defined in
armada-cp110.dtsi.
Fixes a hang in probing the mvmdio driver that was encountered on the
Clearfog GT 8K with all drivers built as modules, but also affects other
boards such as the MacchiatoBIN.
Cc: stable@vger.kernel.org
Fixes: 96cb434238 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 8040 needs four clocks to be enabled for MDIO accesses to work.
Update the binding to allow the extra clock to be specified.
Cc: stable@vger.kernel.org
Fixes: 6d6a331f44 ("dt-bindings: allow up to three clocks for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver starts using page_pool buffers before calling
xdp_rxq_info_reg_mem_model(). Start using the buffers after the
registration succeeded, so we won't have to call
page_pool_request_shutdown() in case of failure
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Some improvements and a fix
Some performace improvements (01/03 and 03/03) and a fix (02/03), all for -next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mapping and unmapping DMA region is an high bottleneck in stmmac driver,
specially in the RX path.
This commit introduces support for Page Pool API and uses it in all RX
queues. With this change, we get more stable troughput and some increase
of banwidth with iperf:
- MAC1000 - 950 Mbps
- XGMAC: 9.22 Gbps
Changes from v3:
- Use page_pool_destroy() (Ilias)
Changes from v2:
- Uncoditionally call page_pool_free() (Jesper)
Changes from v1:
- Use page_pool_get_dma_addr() (Jesper)
- Add a comment (Jesper)
- Add page_pool_free() call (Jesper)
- Reintroduce sync_single_for_device (Arnd / Ilias)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a993db88d1 ("net: stmmac: Enable support for > 32 Bits
addressing in XGMAC"), introduced support for > 32 bits addressing in
XGMAC but the conversion of descriptors to dma_addr_t was left out.
As some devices assing coherent memory in regions > 32 bits we need to
set lower and upper value of descriptors address when initializing DMA
channels.
Luckly, this was working for me because I was assigning CMA to < 4GB
address space for performance reasons.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for coalescing RX path by specifying number of frames which
don't need to have interrupt on completion bit set.
This is only available when RX Watchdog is enabled.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_destroy() in bnxt_free_rx_rings() during normal RX ring
cleanup, as Ilias has informed us that the following commit has been
merged:
1da4bbeffe ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy")
The special error handling code to call page_pool_free() can now be
removed. bnxt_free_rx_rings() will always be called during normal
shutdown or any error paths.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey says:
====================
net/sched: Introduce tc connection tracking
This patch series add connection tracking capabilities in tc sw datapath.
It does so via a new tc action, called act_ct, and new tc flower classifier matching
on conntrack state, mark and label.
Usage is as follows:
$ tc qdisc add dev ens1f0_0 ingress
$ tc qdisc add dev ens1f0_1 ingress
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 0 proto ip \
flower ip_proto tcp ct_state -trk \
action ct zone 2 pipe \
action goto chain 2
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower ct_state +trk+new \
action ct zone 2 commit mark 0xbb nat src addr 5.5.5.7 pipe \
action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
action ct nat pipe \
action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_1 ingress \
prio 1 chain 0 proto ip \
flower ip_proto tcp ct_state -trk \
action ct zone 2 pipe \
action goto chain 1
$ tc filter add dev ens1f0_1 ingress \
prio 1 chain 1 proto ip \
flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
action ct nat pipe \
action mirred egress redirect dev ens1f0_0
The pattern used in the design here closely resembles OvS, as the plan is to also offload
OvS conntrack rules to tc. OvS datapath rules uses it's recirculation mechanism to send
specific packets to conntrack, and return with the new conntrack state (ct_state) on some other recirc_id
to be matched again (we use goto chain for this).
This results in the following OvS datapath rules:
recirc_id(0),in_port(ens1f0_0),ct_state(-trk),... actions:ct(zone=2),recirc(2)
recirc_id(2),in_port(ens1f0_0),ct_state(+new+trk),ct_mark(0xbb),... actions:ct(commit,zone=2,nat(src=5.5.5.7),mark=0xbb),ens1f0_1
recirc_id(2),in_port(ens1f0_0),ct_state(+est+trk),ct_mark(0xbb),... actions:ct(zone=2,nat),ens1f0_1
recirc_id(1),in_port(ens1f0_1),ct_state(-trk),... actions:ct(zone=2),recirc(1)
recirc_id(1),in_port(ens1f0_1),ct_state(+est+trk),... actions:ct(zone=2,nat),ens1f0_0
Changelog:
See individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 13 tests ensuring the command line is doing what is supposed to do.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New matches for conntrack mark, label, zone, and state.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreives connection tracking zone, mark, label, and state from
a SKB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow sending a packet to conntrack module for connection tracking.
The packet will be marked with conntrack connection's state, and
any metadata such as conntrack mark and label. This state metadata
can later be matched against with tc classifers, for example with the
flower classifier as below.
In addition to committing new connections the user can optionally
specific a zone to track within, set a mark/label and configure nat
with an address range and port range.
Usage is as follows:
$ tc qdisc add dev ens1f0_0 ingress
$ tc qdisc add dev ens1f0_1 ingress
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 0 proto ip \
flower ip_proto tcp ct_state -trk \
action ct zone 2 pipe \
action goto chain 2
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower ct_state +trk+new \
action ct zone 2 commit mark 0xbb nat src addr 5.5.5.7 pipe \
action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
action ct nat pipe \
action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_1 ingress \
prio 1 chain 0 proto ip \
flower ip_proto tcp ct_state -trk \
action ct zone 2 pipe \
action goto chain 1
$ tc filter add dev ens1f0_1 ingress \
prio 1 chain 1 proto ip \
flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
action ct nat pipe \
action mirred egress redirect dev ens1f0_0
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Changelog:
V5->V6:
Added CONFIG_NF_DEFRAG_IPV6 in handle fragments ipv6 case
V4->V5:
Reordered nf_conntrack_put() in tcf_ct_skb_nfct_cached()
V3->V4:
Added strict_start_type for act_ct policy
V2->V3:
Fixed david's comments: Removed extra newline after rcu in tcf_ct_params , and indent of break in act_ct.c
V1->V2:
Fixed parsing of ranges TCA_CT_NAT_IPV6_MAX as 'else' case overwritten ipv4 max
Refactored NAT_PORT_MIN_MAX range handling as well
Added ipv4/ipv6 defragmentation
Removed extra skb pull push of nw offset in exectute nat
Refactored tcf_ct_skb_network_trim after pull
Removed TCA_ACT_CT define
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit says:
====================
devlink: Introduce PCI PF, VF ports and attributes
This patchset carry forwards the work initiated in [1] and discussion
futher concluded at [2].
To improve visibility of representor netdevice, its association with
PF or VF, physical port, two new devlink port flavours are added as
PCI PF and PCI VF ports.
A sample eswitch view can be seen below, which will be futher extended to
mdev subdevices of a PCI function in future.
Patch-1 moves physical port's attribute to new structure
Patch-2 enhances netlink response to consider port flavour
Patch-3,4 extends devlink port attributes and port flavour
Patch-5 extends mlx5 driver to register devlink ports for PF, VF and
physical link.
+---+ +---+
vf| | | | pf
+-+-+ +-+-+
physical link <---------+ | |
| | |
| | |
+-+-+ +-+-+ +-+-+
| 1 | | 2 | | 3 |
+--+---+-----+---+------+---+--+
| physical vf pf |
| port port port |
| |
| eswitch |
| |
+------------------------------+
[1] https://www.spinics.net/lists/netdev/msg555797.html
[2] https://marc.info/?l=linux-netdev&m=155354609408485&w=2
Changelog:
v5->v6:
- Fixed port flavour check order for PCI PF vs other flavours in
netlink response.
- Changed 'physical' to 'phys'.
v4->v5:
- Split first patch to two patches to handle netlink response in
separate patch.
- Corrected typo 'otwerwise' to 'otherwise' in patches 3 and 4.
v3->v4:
- Addressed comments from Jiri.
- Split first patch to two patches.
- Renamed phys_port to physical to be consistent with pci_pf.
- Removed port_number from __devlink_port_attrs_set and moved
assignment to caller function.
- Used capital letter while moving old comment to new structure.
- Removed helper function is_devlink_phy_port_num_supported().
v2->v3:
- Made port_number and split_port_number applicable only to
physical port flavours.
v1->v2:
- Updated new APIs and mlx5 driver to drop port_number for PF, VF
attributes
- Updated port_number comment for its usage
- Limited putting port_number to physical ports
====================
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register devlink port of physical port, PCI PF and PCI VF flavour
for each PF, VF when a given devlink instance is in switchdev mode.
Implement ndo_get_devlink_port callback API to make use of registered
devlink ports.
This eliminates ndo_get_phys_port_name() and ndo_get_port_parent_id()
callbacks. Hence, remove them.
An example output with 2 VFs, without a PF and single uplink port is
below.
$devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0 flavour physical
pci/0000:05:00.0/1: type eth netdev eth1 flavour pcivf pfnum 0 vfnum 0
pci/0000:05:00.0/2: type eth netdev eth2 flavour pcivf pfnum 0 vfnum 1
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI VF may have port which is normally represented using
a representor netdevice.
To have better visibility of eswitch port, its association with VF,
and its representor netdevice, introduce a PCI VF port flavour.
When devlink port flavour is PCI VF, fill up PCI VF attributes of
the port.
Extend port name creation using PCI PF and VF number scheme on best
effort basis, so that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
pci/0000:05:00.0/1: type eth netdev eth1 flavour pcivf pfnum 0 vfnum 0
pci/0000:05:00.0/2: type eth netdev eth2 flavour pcivf pfnum 0 vfnum 1
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI PF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with
PF and a representor netdevice, introduce a PCI PF port
flavour and port attriute.
When devlink port flavour is PCI PF, fill up PCI PF attributes of the
port.
Extend port name creation using PCI PF number on best effort basis.
So that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical port number and split group fields are applicable only to
physical port flavours such as PHYSICAL, CPU and DSA.
Hence limit returning those values in netlink response to such port
flavours.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support additional devlink port flavours and to support few common
and few different port attributes, move physical port attributes to a
different structure.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: tls: fixes for initial TLS support
This series brings various fixes to nfp tls offload recently added
to net-next.
First 4 patches revolve around device mailbox communication, trying
to make it more reliable. Next patch fixes statistical counter.
Patch 6 improves the TX resync if device communication failed.
Patch 7 makes sure we remove keys from memory after talking to FW.
Patch 8 adds missing tls context initialization, we fill in the
context information from various places based on the configuration
and looks like we missed the init in the case of where TX is
offloaded, but RX wasn't initialized yet. Patches 9 and 10 make
the nfp driver undo TLS state changes if we need to drop the
frame (e.g. due to DMA mapping error).
Last but not least TLS fallback should not adjust socket memory
after skb_orphan_partial(). This code will go away once we forbid
orphaning of skbs in need of crypto, but that's "real" -next
material, so lets do a quick fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netem runs skb_orphan_partial() which "disconnects" the skb
from normal TCP write memory accounting. We should not adjust
sk->sk_wmem_alloc on the fallback path for such skbs.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver has to drop the TLS frame it needs to undo the TCP
sequence tracking changes, otherwise device will receive
segments out of order and drop them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the #ifdef CONFIG_TLS_DEVICE a little so we can eliminate
the other one.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out TLS_TX in HW offload mode does not initialize tls_prot_info.
Since commit 9cd81988cc ("net/tls: use version from prot") we actually
use this field on the datapath. Luckily we always compare it to TLS 1.3,
and assume 1.2 otherwise. So since zero is not equal to 1.3, everything
worked fine.
Fixes: 9cd81988cc ("net/tls: use version from prot")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the contents of the skb which carried key material
to the FW is cleared.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a return code for the tls_dev_resync callback.
When the driver TX resync fails, kernel can retry the resync again
until it succeeds. This prevents drivers from attempting to offload
TLS packets if the connection is known to be out of sync.
We don't worry about the RX resync since they will be retried naturally
as more encrypted records get received.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of successfully submitted TLS segments,
not skbs. This will make it easier to compare the TLS
encryption count against other counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the batch limit to consume small message bursts more
effectively. Practically, the effect on the 'add' messages is not
significant since the mailbox is sized such that the 'add' messages are
still limited to the same order of magnitude that it was originally set
for.
Furthermore, increase the queue size limit to 1024 entries. This further
improves the handling of bursts of small control messages.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connection 4 tuple reuse is slightly problematic - TLS socket
and context do not get destroyed until all the associated skbs
left the system and all references are released. This leads
to stale connection entry in the device preventing addition
of new one if the 4 tuple is reused quickly enough.
Instead of using read 4 tuple as the key use a unique ID.
Set the protocol to TCP and port to 0 to ensure no collisions
with real connections.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long lines are ugly. No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to do our best not to drop delete commands, otherwise
we will have stale entries in the connection table. Ignore
the control message queue limits for delete commands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_bind_addr_state() is called either in packet rcv path or
by sctp_copy_local_addr_list(), which are under rcu_read_lock.
So there's no need to call it again in sctp_bind_addr_state().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: tidy up some ep and asoc feature flags
This patchset is to remove some unnecessary feature flags from
sctp_assocation and move some others to the right places.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other endpoint features, strm_interleave should be moved to
sctp_endpoint and renamed to intl_enable.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep consistent with other asoc features, we move intl_enable
to peer.intl_capable in asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like reconf_enable, prsctp_enable should also be removed from asoc,
as asoc->peer.prsctp_capable has taken its job.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
asoc's reconf support is actually decided by the 4-shakehand negotiation,
not something that users can set by sockopt. asoc->peer.reconf_capable is
working for this. So remove it from asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley says:
====================
Add MPLS actions to TC
This patchset introduces a new TC action module that allows the
manipulation of the MPLS headers of packets. The code impliments
functionality including push, pop, and modify.
Also included are tests for the new funtionality. Note that these will
require iproute2 changes to be submitted soon.
NOTE: these patches are applied to net-next along with the patch:
[PATCH net 1/1] net: openvswitch: fix csum updates for MPLS actions
This patch has been accepted into net but, at time of posting, is not yet
in net-next.
v6-v7:
- add extra tests for setting max/min and exceeding range of fields -
patch 5 (Roman Mashak)
v5-v6:
- add CONFIG_NET_ACT_MPLS to tc-testing config file - patch 5
(Davide Caratti)
v4-v5:
- move mpls_hdr() call to after skb_ensure_writable - patch 3
(Willem de Bruijn)
- move mpls_dec_ttl to helper - patch 4 (Willem de Bruijn)
- add iproute2 usage example to commit msg - patch 4 (David Ahern)
- align label validation with mpls core code - patch 4 (David Ahern)
- improve extack message for no proto in mpls pop - patch 4 (David Ahern)
v3-v4:
- refactor and reuse OvS code (Cong Wang)
- use csum API rather than skb_post*rscum to update skb->csum (Cong Wang)
- remove unnecessary warning (Cong Wang)
- add comments to uapi attributes (David Ahern)
- set strict type policy check for TCA_MPLS_UNSPEC (David Ahern)
- expand/improve extack messages (David Ahern)
- add option to manually set BOS
v2-v3:
- remove a few unnecessary line breaks (Jiri Pirko)
- retract hw offload patch from set (resubmit with driver changes) (Jiri)
v1->v2:
- ensure TCA_ID_MPLS does not conflict with TCA_ID_CTINFO (Davide Caratti)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiangfeng Xiao