Bits used only on HDMI mode now have HDMI_ prefix instead of SDVO_.
The COLOR_FORMAT bits now have prefixes (and the 12bpc bit is for HDMI
only).
Notice that this patch uncovers a bug on the SDVO code: the
COLOR_RANGE_16_235 bit can only be used if the port is in TMDS mode,
not SDVO mode. This will have to be fixed in a later patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since they're all the same register, leave all the #defines at the
same place, organized by Gen and also specify which bits are used by
only a specific port or encoding.
Also remove a few unused duplicates and adjust indentation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some HDMI registers can be used for SDVO, so saying "HDMIB" should be
the same as saying "SDVOB" for a given HW generation. This was not
true and led to confusions and even a regression.
Previously we had:
- SDVO{B,C} defined as the Gen3+ registers
- HDMI{B,C,D} and PCH_SDVOB defined as the PCH registers
But now:
- SDVO{B,C} became GEN3_SDVO{B,C} on SDVO code
- SDVO{B,C} became GEN4_HDMI{B,C} on HDMI code
- HDMI{B,C,D} became PCH_HDMI{B,C,D}
- PCH_SDVOB is still the same thing
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commented out and unneeded.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Actually use num_pages (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On G45 some low res modes (800x600 and 1024x768) produce a blank
screen when the display plane is enabled with with cursor plane
off.
Experiments showed that this issue occurred when the following
conditions were met:
a. a previous mode had the cursor plane enabled (Xserver).
b. this mode or the previous one was using self refresh. (Thus
the problem was only seen with low res modes).
The screens lit up as soon as the cursor plane got enabled.
Therefore the blank screen occurred only in console mode, not
when running an Xserver.
It also seemed to be necessary to disable self refresh while briefly
enabling the cursor plane.
Signed-off-by: Egbert Eich <eich@suse.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=61457
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: drop spurious whitespace change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes issue where i2c subdev never gets destroyed due to its subobjects
holding references. This will mean the i2c subdev refcount goes
negative during its destruction, but this isn't an issue in practice.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes script-based modesetting on some LVDS panels.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Kill the HSW check from the single thread force wake code. HSW
uses MT force wake exclusively these days.
The commit that removed HSW single thread forcewake support:
commit 36ec8f8774
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 18 14:44:35 2012 +0200
drm/i915: unconditionally use mt forcewake on hsw/ivb
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the number '1' instead of FORCEWAKE_KERNEL when requesting single
thread force wake since there is only one bit in the register. Using
the FORCEWAKE_KERNEL name might give someone the wrong impression.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The MT forcewake ACK register also has a corresponding bit to each of
the bits in the MT forcewake register. Use the define we have for the
bit we care about instead of a hardcoded number.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code is totally obvious so these comments serve no purpose. What's
worse, one of them was wrong. Just remove them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The load detection code has moved around at some point, but it left
a comment behind. The code now looks to be different enough to make
the comment stale as well. Just remove it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The proper use of find_pll() isn't always so easy to determine from the
code itself. Some documentation should help.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The second digit was off by one, which meant we accidentally treated
GT(n) as GT(n-1). This also meant no support for GT1 at all.
Cc: stable@kernel.org
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Restore crtc->fb to the old framebuffer if queue_flip fails.
While at it, kill the pointless intel_fb temp variable.
v2: Update crtc->fb before queue_flip and restore it back
after a failure.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
to_user_ptr() simply casts a pointer passed as u64 from user space
to void __user * correctly. Using this lets us get rid of all the
tiresome casts.
The idea came from Chris Wilson <chris@chris-wilson.co.uk>.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So ditch that if clause from the i8xx pll update code.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So use msecs_to_jiffies(10) to make the timeout the same as in the
"!has_aux_irq" case.
This patch was initially written by Daniel Vetter and posted on
pastebin a few weeks ago. I'm just bringing it to the mailing list.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While old platforms had 3 transcoders and 3 pipes (1:1), HSW has
4 transcoders and 3 pipes.
These regs were being used only by HDMI code where pipe is always the same
thing as cpu_transcoder.
This patch allow us to use them for DP, specially for TRANSCODER_EDP.
v2: Adding HSW_TVIDEO_DIP_VSC_DATA to transmit vsc to eDP.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to initialize the variable wait to false.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
idr_destroy() can destroy idr by itself and idr_remove_all() is being
deprecated. Drop its usage.
* drm_ctxbitmap_cleanup() was calling idr_remove_all() but forgetting
idr_destroy() thus leaking all buffered free idr_layers. Replace it
with idr_destroy().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
[airlied: hack for now until we fix cma helpers on other OF platforms]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Thierry writes:
"Remove a duplicate implementation of the CEA VIC lookup and move the CEA
and other mode tables to drm_edid.c to make it more difficult to create
duplicates of the tables.
Add some helpers to pack CEA-861/HDMI AVI, audio and SPD infoframes into
binary buffers that can easily be written into hardware registers. A new
helper function makes it easy construct an AVI infoframe from a DRM
display mode.
Convert the Tegra and Radeon drivers to use the new HDMI helpers."
* 'drm/hdmi-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
This reverts
commit 8ec22b214d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri May 11 18:01:34 2012 +0100
drm/i915/hdmi: Query the live connector status bit for G4x
and
commit b0ea7d37a8
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Thu Dec 13 16:09:00 2012 +0000
drm/i915/hdmi: Read the HPD status before trying to read the EDID
They reliably cause HDMI to not be detected on some systems (like my
ivb or the bug reporters gm45). To fix up the very slow unplug issues
we might want to fire up a 2nd detect cycle a few hundred ms after
each hotplug. But for now at least make displays work again.
I somewhat suspect that this is confined to HDMI connectors, since all
the machines I have with DP+ outputs work correctly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org.kernel.org # for 8ec22b21
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This list is most useful to inspect whether framebuffer reference
counting works as expected. The code is loosely based on the i915
implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
bpp stores the number of bytes per pixel, but color expansion needs to
be enabled for less than 24 bits per pixel.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The Tegra TRM says that the ACT_REQ and UPDATE fields cannot be
programmed at the same time so they are updated in two consecutive
writes instead.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All the necessary support bits like .mode_set_base() and VBLANK are now
available, so page-flipping case easily be implemented on top.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Implement support for the VBLANK IOCTL. Note that Tegra is somewhat
special in this case because it doesn't use the generic IRQ support
provided by the DRM core (DRIVER_HAVE_IRQ) but rather registers one
interrupt handler for each display controller.
While at it, clean up the way that interrupts are enabled to ensure
that the VBLANK interrupt only gets enabled when required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The sequence for replacing the scanout buffer is much shorter than a
full mode change operation so implementing this callback considerably
speeds up cases where only a new framebuffer is to be scanned out.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for the B and C planes which support RGB and YUV pixel
formats and can be used as overlays or hardware cursor. Currently 32-bit
XRGB as well as UYVY, YUV420 and YUV422 pixel formats are advertised.
Other formats should be easy to add but these are the most common ones
and should cover the majority of use-cases.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tegra uses the CMA FB helpers so framebuffers passed to the driver need
to use the corresponding functions to access the underlying GEM objects.
This used to work because struct tegra_framebuffer was sufficiently
similar to struct drm_fb_cma but that isn't guaranteed to stay that way.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Driver implementations of the drm_crtc's .page_flip() function are
required to update the crtc->fb field on success to reflect that the new
framebuffer is now in use. This is important to keep reference counting
on the framebuffers balanced.
While at it, document this requirement to keep others from falling into
the same trap.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the generic HDMI infoframe helpers to get rid of the duplicate
implementation in the radeon driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Use the generic HDMI infoframe helpers to get rid of the NVIDIA Tegra
reimplementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Add a generic helper to fill in an HDMI AVI infoframe with data
extracted from a DRM display mode.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The modes are only used from within drm_edid.c so we move them there to
avoid creating duplicates by multiple inclusion of drm_edid_modes.h. As
a side-effect we can also get rid of a few variables that keep track of
the number of entries in the tables and use ARRAY_SIZE() instead.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The same function had already been merged with a different name. Remove
the duplicate one but reuse some of its kerneldoc fragments for the
existing implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
The summary:
. Add display mode check operaion to mixer driver
- Mixer IP also can put certain restrictions on the proposed
display modes and these restrictions need to be considered
during mode negotiation, which happens immediately after
edid parsing.
. Set correct mode for range of resolutions
- With this patch, the mixer driver could find the correct mode
for the range of resolutions upto 1080 vertical lines.
. Support extra resolution for hdmi
- This patch programs the core and timing generator registers
using the timing data provided in drm_display_mode without
hard-coded configurations. So this patch adds additional PHY
configs to allow us to support more permissible resolutions
and refresh rates.
. Add device tree support for g2d
- This patch adds just the compatible string for exynos5250 SoC
so that with device tree enabling, this driver can be probed.
. And bug fixes and code cleanups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Add device tree based discovery support for G2D
drm/exynos: hdmi: support extra resolutions using drm_display_mode timings
drm/exynos: mixer: set correct mode for range of resolutions
drm/exynos: implement display-mode-check callback in mixer driver
drm/exynos: add display-mode-check operation to exynos_mixer_ops struct
drm/exynos: release resources properly when fb creation is failed.
drm/exynos: fix wrong pointer access at vm close.
drm/exynos: Add missing braces around sizeof
drm/exynos: consider exception case to fb handle creation
drm/exynos: fix iommu address allocation order
The values of n, m1 and m2 needs to be subtracted by 2 before writing them to
the FP register. The dot clock calculation already thinks of these values in
register form so we must also specify them as such.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
Fixes regression from commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Caching the PIPESTAT enable bits has been deemed pointless. Just
read them from the register itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch programs the core and timing generator registers using the
timing data provided in drm_display_mode and not using hard-coded
configurations.
Additional PHY configs has been added. This allows us to support more
permissible resolutions and refresh rates.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Akshay Saraswat <Akshay.s@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With this patch, mixer driver find the correct resolution mode for
the range of resolutions, upto 1080 vertical lines. Resolution will
be categorized to NTSC SD, PAL SD or HD and the correct mode is
set to the mixer configuration register.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds the implementation of check_timing callback in the mixer
driver. Based on the mixer version, correct set of restrictions will be
exposed by the mixer driver. A resolution will be acceptable only if passes
the criteria set by mixer and hdmi IPs.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds the display mode check operation to exynos_mixer_ops
in drm-common-hdmi. In Exynos SoCs, mixer IP can put certain restrictions
on the proposed display modes. These restriction needs to be considered
during mode negotiation, which happens immediately after edid parsing.
Both, mixer check-mode and hdmi check-timing callbacks are called one after
another and ANDed result is returned back.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch releases allocated resources properly when
exynos_user_fb_create() is failed.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes wrong pointer access issue to filp->f_op and
filp->private_data.
The exynos_drm_gem_mmap_ioctl() changes filp->f_op and
filp->private_data temporarily and restore them to use
original ones in exynos_drm_gem_mmap_buffer() but there
was no lock between the changing and the restoring so
wrong pointer access to filp->f_op and filp->private_data
was induced by vm close callback.
So this patch uses mutex lock properly to resolve this issue.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes the following checkpatch warning:
WARNING: sizeof *sgt should be sizeof(*sgt)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
GETFB ioctl request creates a new handle to only one gem object
so it should check if the given fb has one gem object.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch modifies iommu address allocation order from 64k
to 4k. 64k order causes waste of the io space and this was
our mistakes.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
More drm-next bits for radeon. Just bug fixes.
* 'drm-next-3.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: properly validate the atpx interface
drm/radeon: switch get_gpu_clock() to a callback (v2)
drm/radeon: add a asic callback to get the xclk
drm/radeon: Avoid NULL pointer dereference from atom_index_iio() allocation failure
drm/radeon: remove overzealous warning in hdmi handling
drm/radeon: fix multi-head power profile stability on BTC+ asics
restore debugfs vbios, fix multiple actions with supervisor intrs
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: restore debugfs/vbios.rom support
drm/nv50-/kms: remove UPDATE methods after each encoder disconnect
drm/nvd0/disp: handle multiple actions from one set of supervisor intrs
drm/nv50/disp: handle multiple actions from one set of supervisor intrs
The indentation is getting way too deep. Pull the vblank interupt
handling out to separate functions.
v2: Keep flip_mask handling in the main irq handler and
flatten {i8xx,i915}_handle_vblank() even further.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the gen3 logic for handling page flip interrupts on gen4.
Unfortuantely this kills the stall_check since that looks like it can
easily trigger too early. With the current logic the stall check would
kick in on the first vblank after the flip has been submitted to the
ring. If the CS takes longer than that to process the commands in the
ring, the stall check will cause the page flip to be complete too
early. That doesn't sound like a very good idea. Something better
should be deviced if we still need the stall check. For now, mark
i915_pageflip_stall_check() as unused.
v2: Fix irq enable_mask and add __always_unused (Chris Wilson)
References: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/1116587
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the interrupt handler were to process a previous vblank interrupt and
the following flip pending interrupt at the same time, the page flip
would be completed too soon.
To eliminate this race, check the live pending flip status from the ISR
register before finishing the page flip.
v2: Added a comment explaining the logic (by Chris Wilson)
v3: Fix a typo in the comment
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to get the reference clock used
by the gfx engine for things like timestamps. Fixes
support for GL extensions the use timestamps on
certain boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Smatch anlysis:
drivers/gpu/drm/radeon/atom.c:1242 atom_index_iio() error: potential null
dereference 'ctx->iio'. (kzalloc returns null)
Also cleaned up some checks before calls to kfree(). kfree(NULL) is OK.
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nothing terribly exciting in here probably:
- reworked thermal stuff from mupuf/I, has a chance of possibly working
well enough when we get to being able to reclock..
- driver will report mmio access faults on chipsets where it's supported
- will now sleep waiting on fences on nv84+ rather than polling
- some cleanup of the internal fencing, looking towards sli/dmabuf sync
- initial support for anx9805 dp/tmds encoder
- nv50+ display fixes related to the above, and also might fix a few
other issues
- nicer error reporting (will log process names with channel errors)
- various other random fixes
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (87 commits)
nouveau: ACPI support depends on X86 and X86_PLATFORM_DEVICES
drm/nouveau/i2c: add support for ddc/aux, and dp link training on anx9805
drm/nv50: initial kms support for off-chip TMDS/DP encoders
drm/nv50-/disp: initial supervisor support for off-chip encoders
drm/nv50-/disp: initial work towards supporting external encoders
drm/nv50-/kms: remove unnecessary wait-for-completion points
drm/nv50-/disp: move DP link training to core and train from supervisor
drm/nv50-/disp: handle supervisor tasks from workqueue
drm/nouveau/i2c: create proper chipset-specific class implementations
drm/nv50-/disp: 0x0000 is a valid udisp config value
drm/nv50/devinit: reverse the logic for running encoder init scripts
drm/nouveau/bios: store a type/mask hash in parsed dcb data
drm/nouveau/i2c: extend type to 16-bits, add lookup-by-type function
drm/nouveau/i2c: aux channels not necessarily on nvio
drm/nouveau/i2c: fix a bit of a thinko in nv_wri2cr helper functions
drm/nouveau/bios: parse external transmitter type if off-chip
drm/nouveau: store i2c port pointer directly in nouveau_encoder
drm/nouveau/i2c: handle i2c/aux mux outside of port lookup function
drm/nv50/graph: avoid touching 400724, it doesn't exist
drm/nouveau: Fix DPMS 1 on G4 Snowball, from snow white to coal black.
...
If I build nouveau on ia64, Kconfig warns:
warning: (DRM_NOUVEAU) selects ACPI_WMI which has unmet direct dependencies (X86 && X86_PLATFORM_DEVICES && ACPI)
warning: (DRM_NOUVEAU) selects MXM_WMI which has unmet direct dependencies (X86 && X86_PLATFORM_DEVICES && ACPI_WMI)
Make all the ACPI support depend on X86 and select
X86_PLATFORM_DEVICES.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to be able to do link training for PIOR-connected ANX9805 from
the third supervisor handler (due to script ordering in the bios, can't
have the "user" call train because some settings are overwritten from
the modesetting bios scripts).
This moves link training for SOR-connected DP encoders to the second
supervisor interrupt, *before* we call the modesetting scripts (yes,
different ordering from PIOR is necessary). This is useful since we
should now be able to remove some hacks to workaround races between
the supervisor and link training paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A single U encoder table can match multiple DCB entries, whereas the
reverse is not true and can lead to us not matching a DCB entry at
all, and fail to initialise some encoders.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For off-chip transmitters we won't necessarily have an i2c table entry
to lookup, but we can do it instead by encoding the type to include
the extdev type and looking that up instead.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is about to become somewhat more complicated to determine in a
number of cases, so store the "common" case (DDC/AUX) directly inside
the encoder structure.
Pre-nv50 code not touched except to fill the pointer, don't care.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not quite how I want it yet, but, I'll fix that at some point. For
right now, it's needed because find() won't necessarily be used right
before a transaction anymore.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=40275.
Signed-off-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
"data" is a void pointer and "args" is "data" after we have casted it to
a struct. We care about the size of the struct here. Btw,
sizeof(*data) is 1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Now can be used to operate on any buffer mapped into the GPU virtual
address and not just the main inter-channel sync buffer.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allows most of the code to be shared between nv84/nvc0 implementations,
and paves the way for doing emit/sync on non-VRAM buffers (multi-gpu,
dma-buf).
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Generated if you try and use fifo method 0x20 on any subchannel, appears
that it can be safely masked off without stalling the whole GPU.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This removes the nastiness with the interactions between display and
software engines when handling vblank semaphore release interrupts.
Now, all the semantics are handled in one place (sw) \o/.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Logs extra info for interrupts that have a sub-status register, and
handles the "special" ack from INTR bit 31.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
orderly_poweroff cannot be called from atomic context.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Current uninitialized sensor detection does not work for me on nv4b and
sensor returns crazy values (>190°C). It stabilises later, but it's too
late - therm code shutdowns the machine...
Let's just reset it on init.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
+ the same for shutdown threshold - seems impossible, but shutdown can fail.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes "BUG: spinlock bad magic" on module load for nva3+ cards.
Introduced in commit "drm/nouveau/therm: implement support for temperature
alarms".
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
the variable chan is dereferenced in line 190, so it is no reason to check
null again in line 198.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's safe to call kfree(NULL).
Found by smatch.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
fan->get returns int, but we write it to unsigned variable, and then check
whether it's >= 0 (it always is)
Found by smatch:
drivers/gpu/drm/nouveau/core/subdev/therm/fan.c:61 nouveau_fan_update() warn: always true condition '(duty >= 0) => (0-u32max >= 0)'
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
COPY_ZM_REG: destination and source addresses were swapped
RAM_RESTRICT_ZM_REG_GROUP: missing 0x prefix for register address
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We already rely on them having the same fields and layout.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This fixes a bug where, when temperature is outside of the linear range, fan
pwm would be outside of the allowed range ([0, 100]) and could get negative in
some cases.
It seems like a regression that happened when we re-worked the fan management
logic before merging.
Tested-by: Ozan Çağlayan <ozancag@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- record channel owner process name
- add some helpers for accessing this information
- let nouveau_enum hold additional value (will be needed in the next patch)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Paulo Zanoni