This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since for ULP1 PM mode of SAMA5D2 the wakeup sources are limited and
well known add a method to check if these wakeup sources are defined by
user (either via DT or filesystem). In case there are no wakeup sources
defined for ULP1 the PM suspend will fail, otherwise these will be
configured in fast startup registers of PMC. Since wakeup sources of
ULP1 need also to be configured in SHDWC registers the code was a bit
changed to map the SHDWC also in case ULP1 is requested by user (this
was done in the initialization phase). In case the ULP1 initialization
fails the ULP0 mode is used (this mode was also used in case backup mode
initialization failed).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In the ULP1 mode, in order to achieve the lowest power consumption
with the system in retention mode and be able to resume on the wake
up events, all the clocks are shut off, inclusive the embedded 12MHz
RC oscillator, and the number of wake up sources is limited as well.
When the wake up event is asserted, the embedded 12MHz RC oscillator
restarts automatically.
The ULP1 (Ultra Low-power mode 1) is introduced by SAMA5D2.
The previous size of pm_suspend.o was 2148 bytes. With the addition of
ULP1 mode the new size of pm_suspend.o raised at 2456 bytes.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: aligned with 4.18-rc1]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch to use ULP0 naming instead of slow clock naming for power modes, to
be as closed as possible to datasheet. This commit does the necessary
renaming and macro addition to be as close as possible to the namings
from [1].
[1] https://lore.kernel.org/lkml/1470650705-31418-3-git-send-email-wenyou.yang@atmel.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.
This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]
https://octavosystems.com/octavo_products/osd3358-sm-red/
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like I made a nasty typo in the original patch which resulted
in missing watchdog device. Fix it.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pwm node should not be under gpio6 node in the device tree.
This fixes detection of the pwm on Droid 4.
Fixes: 6d7bdd328d ("ARM: dts: omap4-droid4: update touchscreen")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This display configuration isn't working as-is as it depends on the
tfp410 LCD to HDMI bridge. This will need to be updated later once
the DRM MXSFB driver will be the default.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6sl soc has gpu_2d and gpu_vg, no 3d support:
etnaviv-gpu 2200000.gpu: model: GC320, revision: 5007
etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
The IP blocks seem to be already supported.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the the DRM driver for MXSFB LCD controller (used in i.MX23/
i.MX28/i.MX6SX or i.MX7). Remove CONFIG_FB_MXS which will soon be
removed.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the the DRM driver for MXSFB LCD controller (used in i.MX23/
i.MX28/i.MX6SX or i.MX7). Remove CONFIG_FB_MXS which will soon be
removed.
Note that this does not remove CONFIG_FB. CONFIG_FB gets selected
implicity by CONFIG_DRM/CONFIG_DRM_KMS_FB_HELPER.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-rdu1 has an external watchdog in the environment
microcontroller, so disable the internal one.
This aligns with what was done in commit 7055f71403 ("ARM: dts:
imx6: RDU2: disable internal watchdog") for imx6 rdu2 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Relying on an unchecked of_iomap() which can return NULL is problematic
here, an explicit check seems mandatory. Also the call to
of_find_compatible_node() returns a device node with refcount incremented
therefor an explicit of_node_put() is needed here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit 22bae42904 ("ARM: hi3xxx: add hotplug support")
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
of_find_compatible_node() returns a device node with refcount incremented
and thus needs an explicit of_node_put(). Further relying on an unchecked
of_iomap() which can return NULL is problematic here, after all ctrl_base
is critical enough for hix5hd2_set_cpu() to call BUG() if not available
so a check seems mandated here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
0002 Fixes: commit 06cc5c1d4d ("ARM: hisi: enable hix5hd2 SoC")
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
of_iomap() can return NULL which seems critical here and thus should be
explicitly flagged so that the cause of system halting can be understood.
As of_find_compatible_node() is returning a device node with refcount
incremented it must be explicitly decremented here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit 7fda91e731 ("ARM: hisi: enable smp for HiP01")
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Normally, we didn't release this kind of baord to user. This specific
board exists only in the early stage of development inside MediaTek -
and that may confuse peoples.
Hence this patch removes related files accordingly.
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved memory for the VGA frame buffer is at the wrong address
for this system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is an eval board, it makes sense to enable many
functions by default. This changes the device-tree to
set port A to be a USB device and leave port B as a
host, along with a little comment explaining how to
change it.
(the vhub device can only exist on port A on this SoC)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
This also adds the missing pinmux definition for it
(the kernel driver already knows about it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the (disabled by default) device node for the
Aspeed virtual hub,a long with clocks and pinmux.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCIs so boards don't have to do
it an document why it is not set for UHCI.
Remove the properties from the AST2500 EVB board which are
now redundant
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the default pinmux for EHCI so boards don't have to do
it, and document why it is not set for UHCI.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pio-leds (near GPIO-Header) are swapped and LOW-active.
This patch restores the expected behaviour.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Instead of setting the DMA ops pointer to NULL, set the correct,
non-IOMMU ops depending on the device's coherency setting.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- A fix for OMAP5 and DRA7 to make the branch predictor hardening
settings take proper effect on secondary cores
- Disable USB OTG on am3517 since current driver isn't working
- Fix thermal sensor register settings on Armada 38x
- Fix suspend/resume IRQs on pxa3xx
-----BEGIN PGP SIGNATURE-----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=lmky
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- A fix for OMAP5 and DRA7 to make the branch predictor hardening
settings take proper effect on secondary cores
- Disable USB OTG on am3517 since current driver isn't working
- Fix thermal sensor register settings on Armada 38x
- Fix suspend/resume IRQs on pxa3xx
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
ARM: dts: armada-38x: use the new thermal binding
- Add Vitesse switch chips
- Add a new DT for a reference design
-----BEGIN PGP SIGNATURE-----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=3RrW
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.19:
- Add Vitesse switch chips
- Add a new DT for a reference design
* tag 'gemini-dts-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add devicetree for Storlink/Storm SL93512R
ARM: dts: Add Vitesse G5e switch to the Gemini SQ201
ARM: dts: Add WAN ethernet port to the SQ201
Signed-off-by: Olof Johansson <olof@lixom.net>
The Storlink Gemini324 EV-Board also known as Storm
Semiconductor SL93512R_BRD is ground zero for the Gemini
devices. We add a device tree so we can support it, it
turns out to be pretty trivial.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Vitesse G5e ethernet switch to the Square
One Itian SQ201 router device tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This sets up the ethernet interface and PHY for the
WAN ethernet port which uses a Marvell PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
-----BEGIN PGP SIGNATURE-----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=Wci4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0eB8QAKCRALBhiOFHI7
1a0PAKCRyt0vXcjr9HHBzhagibfgT4XrXgCfXG43C32Qjg5U1Ga39IIY3fcFMrY=
=2Pjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.18 (part 1)
Use the new thermal binding on Armada 38x allowing to use a driver fix
which is already part of the kernel.
* tag 'mvebu-fixes-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: use the new thermal binding
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a fix for suspending all pxa3xx platforms, where high
number interrupts are not reenabled.
-----BEGIN PGP SIGNATURE-----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=nVSa
-----END PGP SIGNATURE-----
Merge tag 'pxa-fixes-4.18' of https://github.com/rjarzmik/linux into fixes
This is the fixes set for v4.18 cycle.
This is a fix for suspending all pxa3xx platforms, where high
number interrupts are not reenabled.
* tag 'pxa-fixes-4.18' of https://github.com/rjarzmik/linux:
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCisQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfrxCACbf7LkN/oH1MekD7CTaGHwlyvyneVWT/Dl
wM0YdKJ4fpZ6FMWxGV4F32qdkSEyPxCVTe1mnueOVnDgZX/ywPGC/hpbofPbmZuq
Z2/YFfCNzsBcijlhwI5bZrzChl/AKKOZNqGBxpKz+lXe/6dIl8bTG8Fmi3tvA+oy
hhvy0Sl6JeNqI5NghEukrQOuEYPHdniElTBYP8DP0J8yypbuIVFOzqpRtoOKeSCP
669aN5G5tCRYoJlx0pC2FyqTI0bdCPtPLPZx9eQwMqyFGN4EUx7NGB3w4gH4GubT
vfG4K4cK3CSWr7+LfwqkA2cX2gzPpGpUyaCpROHkGxtxqcMFdIrV
=ZfMG
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Fix for a new warning from dtc in graph node unit addresses.
* tag 'v4.18-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix graph node unit address error from dtc
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a single fix for the Trusted Foundations firmware
implementation, used on some Tegra20 and Tegra30 platforms.
-----BEGIN PGP SIGNATURE-----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=SJEE
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.19-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
firmware: tegra: Changes for v4.19-rc1
This contains a single fix for the Trusted Foundations firmware
implementation, used on some Tegra20 and Tegra30 platforms.
* tag 'tegra-for-4.19-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: trusted_foundations: do not use naked function
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes are mostly PM related changes for am335x and
am437x to support RTC only suspend mode. Some of the clock
and driver related chances are still pending so it's not
yet fully functional.
Also included is a change for PM debug sysfs entry to use
DEFINE_SHOW_ATTRIBUTE.
-----BEGIN PGP SIGNATURE-----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=Px9o
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC updates for omaps for v4.19 merge window
These changes are mostly PM related changes for am335x and
am437x to support RTC only suspend mode. Some of the clock
and driver related chances are still pending so it's not
yet fully functional.
Also included is a change for PM debug sysfs entry to use
DEFINE_SHOW_ATTRIBUTE.
* tag 'omap-for-v4.19/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: sleep33/43xx: Add RTC-Mode support
ARM: OMAP2+: sleep33/43xx: Make sleep actions configurable
ARM: OMAP2+: reuse DEFINE_SHOW_ATTRIBUTE() macro
ARM: hwmod: RTC: Don't assume lock/unlock will be called with irq enabled
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly a series by Janusz Krzysztofik to clean up the
GPIO and input handling for ams-delta. Because of the
platform data changes, we decided that it's best to
merge the related input changes also via the arm-soc
tree so Dmitry Torokhov has acked the input changes.
Also included is a change to constify gpio_leds from
Arvind Yadav.
-----BEGIN PGP SIGNATURE-----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=0NZG
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/omap1-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC updates for omap1 for v4.19 merge window
Mostly a series by Janusz Krzysztofik to clean up the
GPIO and input handling for ams-delta. Because of the
platform data changes, we decided that it's best to
merge the related input changes also via the arm-soc
tree so Dmitry Torokhov has acked the input changes.
Also included is a change to constify gpio_leds from
Arvind Yadav.
* tag 'omap-for-v4.19/omap1-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: ams-delta: move late devices back to init_machine
Input: ams_delta_serio: Get FIQ buffer from platform_data
Input: ams_delta_serio: use IRQ resource
ARM: OMAP1: Get rid of <mach/ams-delta-fiq.h>
ARM: OMAP1: ams-delta FIQ: Keep serio input GPIOs requested
ARM: OMAP1: ams-delta FIQ: don't use static GPIO numbers
ARM: OMAP1: ams-delta: Hog "keybrd_dataout" GPIO pin
Input: ams_delta_serio: Replace power GPIO with regulator
Input: ams_delta_serio: use private structure
Input: ams_delta_serio: convert to platform driver
ARM: OMAP1: ams-delta: drop GPIO lookup table for serio device
ARM: OMAP1: ams-delta: assign LED GPIO numbers from descriptors
ARM: OMAP1: ams-delta: refactor late_init()
ARM: OMAP1: constify gpio_led
Signed-off-by: Olof Johansson <olof@lixom.net>
After the work done by Thomas Petazzoni, the NAND chip timings
can be read out from the chip instead of open coded in the
device tree, so let's just remove the timing information.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable options needed for booting full system on S5Pv210-based Samsung
Galaxy S mobile phones.
-----BEGIN PGP SIGNATURE-----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=vPjN
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Samsung defconfig changes for v4.19
Enable options needed for booting full system on S5Pv210-based Samsung
Galaxy S mobile phones.
* tag 'samsung-defconfig-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro
ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones
ARM: s5pv210_defconfig: Run make savedefconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
-----------------------------------
* Enable support for PWM backight and bluetooth
* Remove some vestiges of mach-davinci private clock implementation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbRL5wAAoJEGFBu2jqvgRNncQQAI7d4Qw5HjfWMS/4vj0EM4o+
7KcbpR4dxFqRSPiZzXDTwCHHLZTgVLeclGmGbH4Ev3yI15u+00QcHdIIiHKhNSQc
N9Kuov41h+i+jfCaRe2U6P/l+/S51wd2AnLBsCE5FIZLGurnrFTOuoRSzu7gHSyJ
49ImFEM2bYVShvvgzOhoRXI+RdolRPpZ406Rm6sVchqM2joTTlbPwSUzBP5XJJsk
5/Gk2KDPuKbhdnDys7orqeAIp66zG8mX681P7x5nxJQINUzos03d575w+v2EdYYu
b5ovJD8KD+7o5UBIV+M/5EkZyI4XUs190xW9kviFnu1nE/iODD9inJN3mEoXHILJ
ogSMSa9SvP/oY5XxX+BtQhGLzB3AIK8jPIUuiFy2Hd1yNa3olqND6mTK/Xkz065K
u6vJKgtTED3s+BV8FktGigOo7L3mrbhFaYVUFYBjJuemUwqrCAO6KAQfdci5vIeN
9z/1GtgTLJwd9IazlcvTNFbNq4VgUOfZLgBuJLoDDViBmFfR4aSvpvcr2lQmTTcQ
4ySUvImOKmLdcfUAu7FjdOjL6Ey996C8KdyDwPJBtsPbDS6vRJXh7oLUMiBjTwI/
6i/ERcHPJ9rZTVyOiU8xGiYiJ8LcCXos6Ylj5FGEszoEkVwzaDqyw+Jz97Ukuin+
0MaDJXmYREjUeUztoZOn
=y4ms
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.19/defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/defconfig
DaVinci defconfig updates for v4.19
-----------------------------------
* Enable support for PWM backight and bluetooth
* Remove some vestiges of mach-davinci private clock implementation.
* tag 'davinci-for-v4.19/defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: Enable Bluetooth
ARM: davinci_all_defconfig: remove CONFIG_DAVINCI_RESET_CLOCKS
ARM: davinci_all_defconfig: set CONFIG_BACKLIGHT_PWM=m
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Tc+I
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.19, round 1
Highlights:
----------
-MCU platforms update:
-Update RTC syscfg bindings on stm32f746 and stm32f429
-Update IWDG node with LSI clock name on stm32f429
-MPU STM32MP157 platform update:
-Add HASH support
-Add m_can support and enable it on EV1 board
-Add RTC suppoort and enable it on ED1 board
-Add USB OTG HS support and enable it on EV1 board
-Enable USB Host EHCI on EV1 board
-Add DFSDM support
-Add SPI support
-Add ETH support and enable it on EV1 board
-Add IWDG support and enable it on ED1 board
-Fix useless GPIO aliases and reorder nodes
* tag 'stm32-dt-for-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (22 commits)
ARM: dts: stm32: update iwdg with lsi clock name for stm32f429
ARM: dts: stm32: add iwdg2 support for stm32mp157c-ed1
ARM: dts: stm32: add iwdg2 support for stm32mp157c
ARM: dts: stm32: Reorder nodes in stm32mp157c-ed1
ARM: dts: stm32: remove gpio aliases for stm32mp157c
ARM: dts: stm32: add support of ethernet on stm32mp157c-ev1
ARM: dts: stm32: Add ethernet dwmac on stm32mp1
ARM: dts: stm32: Add syscfg on stm32mp1
ARM: dts: stm32: add SPI1 support on stm32mp157c-ev1
ARM: dts: stm32: add SPI support on stm32mp157c
ARM: dts: stm32: Add DFSDM support to stm32mp157c
ARM: dts: stm32: Add ADC support to stm32mp157c
ARM: dts: stm32: enable USB OTG HS on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG HS support for stm32mp157c SoC
ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp157c-ev1
ARM: dts: stm32: enable RTC on stm32mp157c-ed1
ARM: dts: stm32: add RTC support to stm32mp157c
ARM: dts: stm32: m_can activation on stm32mp157c-ev1
ARM: dts: stm32: m_can support to stm32mp157c
ARM: dts: stm32: Add HASH support on stm32mp157c
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW0hvzAAKCRALBhiOFHI7
1eiZAJ4khxwKduQLyzz0nqyaX7jefrb7ywCfY8WXMc0ay/qwZytGcUUqpWMeY3Y=
=OVdR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.19 (part 1)
- Add a new Armada 388 based board: helios4
- Enable SPI flash by default on SolidRun Armada 38x Microsom
* tag 'mvebu-dt-4.19-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: drop future changes disclaimer
ARM: dts: armada388-clearfog: enable spi flash
ARM: dts: armada388-helios4
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
-----BEGIN PGP SIGNATURE-----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=afvE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.19
1. Add two new S5Pv210 boards: Samsung Galaxy S and Samsung Galaxy S 4G
mobile phones. Both are from family codenamed Aries. The Samsung
Galaxy S was released on the market in 2010 with Android operating
system. At that time, it was the Samsung's flagship model.
This brings support for storage (SD card and internal memory), PMIC,
RTC, fuel-gauge, keys, USB (in peripherial mode) and WiFi.
2. Add missing secondary CPU properties.
3. Cleanup from old files and properties.
* tag 'samsung-dt-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document bindings for SGH-T959P board
dt-bindings: samsung: Document bindings for Samsung aries boards
ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone
ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone
ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones
ARM: dts: s5pv210: Add missing interrupt-controller property to gph2
ARM: dts: exynos: remove no longer needed samsung thermal properties
dt-bindings: arm: Remove obsolete insignal-boards.txt
ARM: dts: exynos: Add missing CPU clocks to secondary CPUs on Exynos542x
arm: dts: exynos: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
-----BEGIN PGP SIGNATURE-----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=+IHO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.19-rc1
This set of changes adds support for the memory client resets on Tegra20
and Tegra30, fixes a couple of issues on Cardhu and Tegra30 Apalis as
well as adds a unit-address to the memory node to avoid warnings from
DTC. To round things of, the NAND flash controller is enabled on the
Tegra20 Colibri.
* tag 'tegra-for-4.19-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra: enable NAND flash on Colibri T20
ARM: dts: tegra: add Tegra20 NAND flash controller node
ARM: tegra: Work safely with 256 MB Colibri-T20 modules
ARM: tegra: Fix unit_address_vs_reg and avoid_unnecessary_addr_size DTC warnings
ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory
ARM: tegra: Remove usage of deprecated skeleton.dtsi
ARM: tegra: Fix can2 on Tegra30 Apalis
ARM: tegra: Fix Tegra30 Cardhu PCA954x reset
ARM: dts: tegra30: Add Memory Client reset to VDE
ARM: dts: tegra20: Add Memory Client reset to VDE
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAltGAUURHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXO1eA//fbUztpM4DFjzFqqsesdkkzyEdgYtcMj/
FtP/pntzzSyP7hqGPTLUhK7qrDUbsxXvBu7AfGer57XjU3IzcrHTmMF5gKTo5Dju
bM+qZL7xYgTnFVkNvVxjY0dLz14PUPEPIYJEzrZ3njc17jlMvCXyfOVnEe3pZfFz
lH2oGmUOJjf05pZCOYqOIxjQM9ggJapHorQ4uM5FHkZSD9T8apoAtmlLlYVTdgkh
bEQIpO+37iuL0Ds06tkJ84SRO/l5P5/Q/jCl72lx8H20Yx56ZdN5ca+jCPwzjjJ3
ZuCyTec/8QPRnFS/jOLCtjM+zam37npxkHcuNujV5SghHntifbg7bN1jYBWIttkc
+q3dRT/eJYCdjQrR2qp54o1megIJpE4RgbvSCfn2/jBAGZKOeNe799HIao9tCm+W
nc62bHUvObHWpMSeyLX8Hi5ywW3UXX7/gCex8oalzL4t+680pTm9/TGZf3WMdwL6
GU+zcvG3uf97dR0eRgTRZX3PBfQyTmU0ACCDNhV0GCUh+p0D/G8U64HiU6ORX6Dy
u9DnSGudOZZTKi99PboN+75A9r3wlzxdq0ko5DPMXYgbgzrj4KzONAaMI2PKaktK
A7pAqtE8/Dos/e/yonBa0H94Ft1pjccKHR/Z8cRKPb50TbOIViMWWwL/CI2ZkwV0
hcT+iy+MrE0=
=v277
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for mcan for omaps for v4.19 merge window
These changes configure the mcan clock, interconnect target
module and mcan device. These changes depend on the ti-sysc
related driver changes and are based on those.
Notably this is the first new driver that probes with ti-sysc
driver with no legacy hwmod platform data for the interconnect
target module.
* tag 'omap-for-v4.19/dt-mcan-v2-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: Add MCAN node
ARM: dts: Add generic interconnect target module node for MCAN
ARM: dts: dra762: Add MCAN clock support
bus: ti-sysc: Add support for software reset
bus: ti-sysc: Add support for using ti-sysc for MCAN on dra76x
clk: ti: dra7: Add clkctrl clock data for the mcan clocks
bus: ti-sysc: Use 2-factor allocator arguments
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
-----BEGIN PGP SIGNATURE-----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=kbfH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
dts changes for omaps for v4.19 merge window
Mostly updates to configure and improve the devices
found on various SoCs and boards:
- several patches to update support for am3517-evm
to replace bogus fixed regulators with proper
regulators and configure various devices such
as wlan, bluetooth and usb1
- add missing cooling devices for omap5 and dra7
- configure dual role for usb ports for am57xx
and dra7
- PM updates for omap4 devices to allow retention
idle for minimal configurations
- am335x-sl50 updates for various devices
- update d-can alias names to not use undescore
- configure pandaboard gpio button
- a non-urgent change to fix dcan node address that
i forgot to send a pull request for earlier
* tag 'omap-for-v4.19/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: pandaboard: add gpio user button
ARM: dts: am3517-evm: Add 'vdd_io_reg' regulator references
ARM: dts: am3517-evm: Enable USB1 Host
ARM: dts: am33xx: Fix syntax of alias names
ARM: dts: am3517-som: Add builtin Bluetooth
ARM: dts: am3517-som: Add WL127x Wifi
ARM: dts: am335x-sl50: enable tsadc on SL50 board
ARM: dts: am335x-sl50: fix label names for all LEDs
ARM: dts: am335x-sl50: use audio-graph-card for sound
ARM: dts: am335x-sl50: add support for DS1339 Real Time Clock
ARM: dts: am335x-sl50: set dr_mode to otg
ARM: dts: am335x-sl50: add a node for the LCD controller
ARM: dts: am335x-sl50: use phy-phandle declarations
ARM: dts: am335x-sl50: update backlight nodes
ARM: dts: omap4-droid4: Use software debounce for gpio-keys
ARM: dts: Configure duovero for to allow core retention during idle
ARM: dts: Improve omap l4per idling with wlcore edge sensitive interrupt
ARM: dts: dra76-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra71-evm: Add VBUS GPIO to USB1/USB2 extcon
ARM: dts: dra7-evm: Add extcon to USB2 port
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6E7c
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci Device-Tree updates for v4.19
-------------------------------------
* DA850 now uses clocks from device-tree
* DA850 EVM gains LCD (with backlight) and SATA support
* Lego Mindstorms gains bluetooth support
* DSP reset control support on DA850
* tag 'davinci-for-v4.19/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Add power-domains to CPPI 4.1 node
ARM: davinci: dts: add a reset control to the dsp node
ARM: davinci: dts: make psc0 a reset provider
ARM: dts: da850-lego-ev3: Add Bluetooth nodes
ARM: dts: da850: Add power-domains to PWM nodes
ARM: dts: da850: Add clocks
dt-bindings: timer: new bindings for TI DaVinci timer
ARM: dts: da850-evm: Enable LCD and backlight
ARM: dts: da850-evm: Enable SATA port
Signed-off-by: Olof Johansson <olof@lixom.net>
-----------------------------
* mach-davinci updates needed to finally move over to common clock framework
* update to use the aemif driver from drivers/memory rather than the
private implementation available in mach-davinci
For the later item, I have included a branch from David Lechner which
should also get merged through the clk tree. The clk dependencies are
needed for aemif conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pwCF
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.19/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
DaVinci SoC updates for v4.19
-----------------------------
* mach-davinci updates needed to finally move over to common clock framework
* update to use the aemif driver from drivers/memory rather than the
private implementation available in mach-davinci
For the later item, I have included a branch from David Lechner which
should also get merged through the clk tree. The clk dependencies are
needed for aemif conversion.
* tag 'davinci-for-v4.19/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (34 commits)
ARM: davinci: unduplicate aemif support
ARM: davinci: mityomapl138: use aemif platform driver
ARM: davinci: dm646x-evm: use aemif platform driver
ARM: davinci: da830-evm: use aemif platform driver
ARM: davinci: dm644x-evm: use aemif platform driver
ARM: davinci: dm365-evm: use the ti-aemif soc driver
ARM: davinci: da850-evm: use aemif platform driver in legacy mode
ARM: davinci: omapl138-hawk: add aemif & nand support
clk: davinci: psc-da830: add a lookup entry for aemif clock
clk: davinci: psc-dm646x: use two lookup entries for the aemif clock
clk: davinci: psc-dm644x: use two lookup entries for the aemif clock
clk: davinci: psc-dm365: use two lookup entries for the aemif clock
clk: davinci: psc-da850: remove the 'davinci_nand.0" lookup
ARM: davinci: da8xx-dt: switch to device tree clocks
ARM: davinci: add device tree support to timer
ARM: davinci: remove legacy clocks
ARM: davinci: da8xx: Remove legacy USB and SATA clock init
ARM: davinci: dm646x: Remove legacy clock init
ARM: davinci: dm644x: Remove legacy clock init
ARM: davinci: dm365: Remove legacy clock init
...
Signed-off-by: Olof Johansson <olof@lixom.net>
4.19, please pull the following:
- Clement re-orders the UART debug entries to be in ascending order and
he also adds the iProc UART3 debug address since that is a common
location for iProc based designs.
-----BEGIN PGP SIGNATURE-----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=dvUl
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/soc' of https://github.com/Broadcom/stblinux into next/soc
This pull request contains Broadcom ARM-based SoCs platform changes for
4.19, please pull the following:
- Clement re-orders the UART debug entries to be in ascending order and
he also adds the iProc UART3 debug address since that is a common
location for iProc based designs.
* tag 'arm-soc/for-4.19/soc' of https://github.com/Broadcom/stblinux:
ARM: debug: fix BCM2836 order entry
ARM: debug: Add iProc UART3 debug addresses
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
-----BEGIN PGP SIGNATURE-----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=lRBW
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.19, please pull the following:
- Clement adds ethernet aliases to the Cygnus DTS include file such that
a DT aware bootloader such as u-boot can properly insert MAC addresses
- Mohamed adds a Device Tree node for the HWRNG found on Cygnus SoCs
- Vivek migrates all the BCM5301x (Northstar) Device Tree sources to use
the proper USB 3.0 PHY representation using its parent MDIO bus.
Vivek also completes the Linksys EA9500 Device Tree by adding support
for LEDs, internal and external switches.
- Rafal adds the ARM architected timer to the BCM53573 Device Tree
include file.
- Eric adds the Performance Monitoring Unit to the BCM2837 DTS include
file since it was absent before
- Boris adds the BCM283x transposer block to the Device Tree
- Stefan adds the Raspberry Pi Compute Module (CM1) Device Tree include
and sources.
* tag 'arm-soc/for-4.19/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Add support for Linksys EA9500
ARM: dts: BCM53573: Add architected timer
ARM: dts: BCM5301X: Make USB 3.0 PHY use MDIO PHY driver
ARM: dts: cygnus: enable iproc-hwrng
ARM: dts: cygnus: add ethernet0 alias
ARM: dts: bcm283x: Add Transposer block
ARM: dts: bcm283x: Add the PMU to the devicetree.
ARM: dts: add Raspberry Pi Compute Module and IO board
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.19, please pull the following:
- Stefan enables the Raspberry Pi voltage sensor driver (HWMON) in both
multi_v7_defconfig and bcm2835_defconfig
-----BEGIN PGP SIGNATURE-----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=C2uA
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/defconfig' of https://github.com/Broadcom/stblinux into next/defconfig
This pull request contains Broadcom ARM-based SoCs defconfig updates
for 4.19, please pull the following:
- Stefan enables the Raspberry Pi voltage sensor driver (HWMON) in both
multi_v7_defconfig and bcm2835_defconfig
* tag 'arm-soc/for-4.19/defconfig' of https://github.com/Broadcom/stblinux:
ARM: multi_v7_defconfig: Enable RPi voltage sensor
ARM: bcm2835_defconfig: Enable RPi voltage sensor
Signed-off-by: Olof Johansson <olof@lixom.net>
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltGCwUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVk2CACbnXTVeS+u/fwgDHA1imCfAjQEGt25yFmV
Yv9GYkFLwvE0dg54Law3u1yYosXuO64Eu3fLZSrOYpI9CadWgMCq+H0rdg3f2Z2Y
mbdW7Ey26U7zGvZkQaEKS7OrUmf5ZQ6TEO70+miQ8Az2G4iEs5fDVRwRN3mJPzV8
Sf5c/dZSQUDD1brKvpTAWpZ4zo4Gx44yBu9DOF6ro9v7h9NNg6Oi6Uuc748Kd8+0
GZLXotcuxPRo2nPpwZYEVgdxHCVkfXezngC0/jc58aYJWbSnqyibrg228siVBDZe
e3p5LyRsn+ALdL5ol1CwRzhShlDIj1GIwZ+jAR87U0hHBT0R6Wdh
=de2o
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
SPDX conversion for existing Rockchip devicetree files as well
as conversion of rk3288 to OPPv2 to facilitate the addition of
missing cpu-cooling-device properties.
* tag 'v4.19-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk3288
ARM: dts: rockchip: convert rk3288 to operating-points-v2
ARM: dts: rockchip: Add missing cooling device properties for CPUs on rk322x
ARM: dts: rockchip: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
Ensure that the stubbed out tcm_init() is marked static, so we don't
end up emitting the stub each time the header is included.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM fixes from Russell King:
"A couple of small fixes this time around from Steven for an
interaction between ftrace and kernel read-only protection, and
Vladimir for nommu"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
ARM: 8775/1: NOMMU: Use instr_sync instead of plain isb in common code
Improve the 64-bit store implementation from:
ldr r6, [fp, #-8]
str r8, [r6]
ldr r6, [fp, #-8]
mov r7, #4
add r7, r6, r7
str r9, [r7]
to:
ldr r6, [fp, #-8]
str r8, [r6]
str r9, [r6, #4]
We leave the store as two separate STR instructions rather than using
STRD as the store may not be aligned, and STR can handle misalignment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rather than writing each 32-bit half of the 64-bit immediate value
separately when the register is on the stack:
movw r6, #45056 ; 0xb000
movt r6, #60979 ; 0xee33
str r6, [fp, #-44] ; 0xffffffd4
mov r6, #0
str r6, [fp, #-40] ; 0xffffffd8
arrange to use the double-word store when available instead:
movw r6, #45056 ; 0xb000
movt r6, #60979 ; 0xee33
mov r7, #0
strd r6, [fp, #-44] ; 0xffffffd4
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Enable the STM32 Real Time Clock (RTC) driver, implemented on STM32MP1 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
MAC is connected to a PHY in RGMII mode.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add Ethernet support (Synopsys MAC IP 4.20a) on stm32mp1 SOC.
Enable feature supported by the stmmac driver, such as TSO.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
System configuration controller is mainly used to manage
the compensation cell and other IOs and system related
settings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SPI1 support on stm32mp157c-ev1 board.
SPI1 is available on GPIO expansion connector but kept disabled
so these pins can be used as GPIOs by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
stm32mp157c has an ADC block with two physical ADCs.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS on STM32MP157C SoC.
USB OTG HS controller is based on DWC2 controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use double-word load and stores where support for this instruction is
supported by the CPU architecture.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Always use an odd/even register pair for our 64-bit registers, so that
we're able to use the double-word load/store instructions in the future.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rearranging the order of the initial tail call code a little allows is
to avoid reloading the 'array' pointer.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Avoid reloading 'index' after we have validated it - it remains in
tmp2[1] up to the point that we begin the code to index the pointer
array, so with a little rearrangement of the registers, we can use
the already loaded value.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rather than pre-shifting the rm register for the ldr in the tail call,
shift it in the load instruction. This eliminates one unnecessary
instruction.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rather than moving constants to a register and then using them in a
subsequent instruction, use them directly in the desired instruction
cutting out the "middle" register. This removes two instructions from
the tail call code path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Provide a version of the imm8m() function that the compiler can optimise
when used with a constant expression.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Access the eBPF scratch space using the frame pointer rather than our
stack pointer, as the offsets from the ARM frame pointer are constant
across all eBPF programs.
Since we no longer reference the scratch space registers from the stack
pointer, this simplifies emit_push_r64() as it no longer needs to know
how many words are pushed onto the stack.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Provide a couple of 64-bit register accessors, and use them where
appropriate
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Many of the code paths need to have knowledge about whether a register
is stacked or in a CPU register. Move this decision making to a pair
of helper functions instead of having it scattered throughout the
code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The decision about whether a BPF register is on the stack or in a CPU
register is detected at the top BPF insn processing level, and then
percolated throughout the remainder of the code. Since we now use
negative register values to represent stacked registers, we can detect
where a BPF register is stored without restoring to carrying this
additional metadata through all code paths.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use negative numbers for eBPF registers that live on the stack.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Provide a set of load/store opcode generators that work with negative
immediates as well as positive ones.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Enumerate the contents of the JIT scratch stack layout used for storing
some of the JITs 64-bit registers, tail call counter and AX register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL1 GPIO is set to output 0
or 1.1V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On i.MX51/i.MX53 it is necessary to set the DBGEN bit in
ARM_GPC register in order to turn on the debug clocks.
The DBGEN bit of ARM_GPC register has the following description
in the i.MX53 Reference Manual:
"This allows the user to manually activate clocks within the debug
system. This register bit directly controls the platform's dbgen_out
output signal which connects to the DAP_SYS to enable all debug clocks.
Once enabled, the clocks cannot be disabled except by asserting the
disable_trace input of the DAP_SYS."
Based on a previous patch from Sebastian Reichel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a label for the PMU node so that the board dts may be able to
pass the 'secure-reg-access' property like this:
&pmu {
secure-reg-access;
};
This also makes it consistent with the PMU node in imx6qdl.dtsi
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX53 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure the M4IF registers as per the vendor bootloader
to avoid visual artifacts during video playback.
This way we don't need to rely on the bootloader configuration for
optimal IPU/VPU bus priorities.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sergey Lapin <sergey.lapin@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual the M4IF register region
starts at 0x83fd8000 and has a 4kB address range.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sergey Lapin <sergey.lapin@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Dynamic ftrace requires modifying the code segments that are usually
set to read-only. To do this, a per arch function is called both before
and after the ftrace modifications are performed. The "before" function
will set kernel code text to read-write to allow for ftrace to make the
modifications, and the "after" function will set the kernel code text
back to "read-only" to keep the kernel code text protected.
The issue happens when dynamic ftrace is tested at boot up. The test is
done before the kernel code text has been set to read-only. But the
"before" and "after" calls are still performed. The "after" call will
change the kernel code text to read-only prematurely, and other boot
code that expects this code to be read-write will fail.
The solution is to add a variable that is set when the kernel code text
is expected to be converted to read-only, and make the ftrace "before"
and "after" calls do nothing if that variable is not yet set. This is
similar to the x86 solution from commit 1623963097 ("ftrace, x86:
make kernel text writable only for conversions").
Link: http://lkml.kernel.org/r/20180620212906.24b7b66e@vmware.local.home
Reported-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
With old bindings imx_gpc_onecell_data always sets num_domains to 2 so
the DISPMIX domain can't actually be referenced. The pd is still defined
and pm core shuts it down as "unused" so display can't work.
Fix this by converting to new gpc bindings by adding pgc nodes and
referencing the newly-defined &pu_disp domain from &lcdif.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, enable it as another mmio sram.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6sl platform has two different cpuidle implementations,
and fails to link if we only want one of the two:
arch/arm/mach-imx/mach-imx6sl.o: In function `imx6sl_init_late':
mach-imx6sl.c:(.init.text+0x12): undefined reference to `imx6sx_cpuidle_init'
This makes the call into reference conditional on the configuration.
Fixes: e7fa1fb39b ("ARM: imx: add cpu idle support for i.MX6SLL")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6SLL cpuidle support reuses the i.MX6SX implementation, but
the Makefile accidentally enables the i.MX6SL one as well, which
then fails with a link error unless the kernel also enables the
the i.MX6SL clock driver:
arch/arm/mach-imx/cpuidle-imx6sl.o: In function `imx6sl_enter_wait':
cpuidle-imx6sl.c:(.text+0x24): undefined reference to `imx6sl_set_wait_clk'
This changes the two lines that were just modified again, hopefully
getting every case right this time.
Fixes: e7fa1fb39b ("ARM: imx: add cpu idle support for i.MX6SLL")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100/200MHz states for USDHC3 are not required since the SoC
does not support modes faster than DDR52 for the on board eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VDDD is connected to VGEN4 of the PF0100. This rail should only
run at 1.8V since there are multiple consumer and they all
expect the rail to be at 1.8V.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fixed 1.8V regulator is not used, and there is in fact no
fixed 1.8V regulator on the module. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the disable-wp to indicate that Apalis and Colibri iMX6 do not
make use of the native write-protect signal available on the i.MX 6
SoCs. This prevents warnings:
mmc0: host does not support reading read-only switch, assuming write-enable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use no-1-8-v device tree property to indicate that the board does
not support 1.8V signaling. The property voltage-ranges seems not
appropriate in our case since we do not have level shifters in
place.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 3.3V main supply on the carrier board. Currently as a fixed
supply since not all consumer are modeled yet. This gets also rid of
some missing supply warnings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_set_aips is assuming that the address returned from of_iomap is
valid which it probably is in the normal case - as the call site
is void error propagation is not possible but never the less at least
a WARN_ON() seems warranted here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit e57e4ab5fc ("ARM: i.MX: allow disabling supervisor protect via DT")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As documented in GCC naked functions should only use basic ASM
syntax. The extended ASM or mixture of basic ASM and "C" code is
not guaranteed. Currently this works because it was hard coded
to follow and check GCC behavior for arguments and register
placement.
Furthermore with clang using parameters in Extended asm in a
naked function is not supported:
arch/arm/firmware/trusted_foundations.c:47:10: error: parameter
references not allowed in naked functions
: "r" (type), "r" (arg1), "r" (arg2)
^
Use a regular function to be more portable. This aligns also with
the other SMC call implementations e.g. in qcom_scm-32.c and
bcm_kona_smc.c.
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit 654f2b937b ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX31 powered boards with OF support Security Random Number
Generator Accelerator RNGA controller is initialized from device tree,
its registration as a platform device is redundant and actually it is
broken due to missing clock information:
mxc_rnga mxc_rnga: Could not get rng_clk!
mxc_rnga: probe of mxc_rnga failed with error -2
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the recent syntax extension, Kconfig is now able to evaluate the
compiler / toolchain capability.
However, accumulating flags to 'LD' is not compatible with the way
it works; 'LD' must be passed to Kconfig to call $(ld-option,...)
from Kconfig files. If you tweak 'LD' in arch Makefile depending on
CONFIG_CPU_BIG_ENDIAN, this would end up with circular dependency
between Makefile and Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Exception return implies context synchronization, so we can hook up the
SYNC_CORE option to sys_membarrier() simply by selecting the Kconfig option,
just like we've done for arm64 already.
Cc: Orion Hodson <oth@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Greg reported that commit 3c24121039 ("ARM: 8756/1: NOMMU: Postpone
MPU activation till __after_proc_init") is causing breakage for the
old Versatile platform in no-MMU mode (with out-of-tree patches):
AS arch/arm/kernel/head-nommu.o
arch/arm/kernel/head-nommu.S: Assembler messages:
arch/arm/kernel/head-nommu.S:180: Error: selected processor does not support `isb' in ARM mode
scripts/Makefile.build:417: recipe for target 'arch/arm/kernel/head-nommu.o' failed
make[2]: *** [arch/arm/kernel/head-nommu.o] Error 1
Makefile:1034: recipe for target 'arch/arm/kernel' failed
make[1]: *** [arch/arm/kernel] Error 2
Since the code is common for all NOMMU builds usage of the isb was a
bad idea (please, note that isb also used in MPU related code which is
fine because MPU has dependency on CPU_V7/CPU_V7M), instead use more
robust instr_sync assembler macro.
Fixes: 3c24121039 ("ARM: 8756/1: NOMMU: Postpone MPU activation till __after_proc_init")
Reported-by: Greg Ungerer <gerg@kernel.org>
Tested-by: Greg Ungerer <gerg@kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This adds a SRAM controller node for the H3, with support for the C1
SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the compatible and commit prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a SRAM controller node for the A23 and A33, with support for
the C1 SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the prefix and the compatibles]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A20 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for sun5i-based platforms. The region is shared
between the Video Engine and the CPU.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size to take the C2 and C3 SRAM into account]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun7i-a20 dtsi to use the most qualified compatibles
for the system-control block (previously named SRAM controller) as well
as the SRAM blocks. The sun4i-a10 compatibles are kept since these
hardware blocks are backward-compatible.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun5i dtsi to use the most qualified compatibles for
the system-control block (previously named SRAM controller) as well as
the SRAM blocks.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Removed the A10 compatible for the driver]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun4i-a10 dtsi to use the new compatible for the
system-control block (previously named SRAM controller) instead of
the deprecated one.
The node name is also updated to reflect the fact that the controller
described is really about system control rather than SRAM control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Amended the commit message]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 has 4 TCONs, but only 2 of them can receive some kind of output at
the same time. Let's disable them by default, so only those which are
really connected on board can be enabled in board dts file.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Current R40 is missing some graph connections between TCON TOP and
TCONs.
Add them.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T and R40 TCON TV are very similar. However, R40 TCON TV is wired
differently, which makes it incompatible with A83T TCON TV.
Because of that, remove fallback A83T TCON TV compatible.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
sun4i-drm DT binding, second paragraph of the first section says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index.
Add mixer ids in R40 DT as mandated by DT binding.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The armpmu uses get_event_idx callback to allocate an event
counter for a given event, which marks the selected counter
as "used". Now, when we delete the counter, the arm_pmu goes
ahead and clears the "used" bit and then invokes the "clear_event_idx"
call back, which kind of splits the job between the core code
and the backend. To keep things tidy, mandate the implementation
of clear_event_idx() and add it for exisiting backends.
This will be useful for adding the chained event support, where
we leave the event idx maintenance to the backend.
Also, when an event is removed from the PMU, reset the hw.idx
to indicate that a counter is not allocated for this event,
to help the backends do better checks. This will be also used
for the chain counter support.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the {read/write}_counter APIs to handle 64bit values
to enable supporting chained event counters. The backends still
use 32bit values and we pass them 32bit values only. So in effect
there are no functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Each PMU defines their max_period of the counter as the maximum
value that can be counted. Since all the PMU backends support
32bit counters by default, let us remove the redundant field.
No functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for the MCAN peripheral which supports both classic
CAN messages along with the new CAN-FD message.
Add MCAN node to evm and enable it with a maximum datarate of 5 mbps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti-sysc driver provides support for manipulating the idle modes
and interconnect level resets.
Add the generic interconnect target module node for MCAN to support
the same.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MCAN is clocked by H14 divider of DPLL_GMAC. Unlike other
DPLL dividers this DPLL_GMAC H14 divider is controlled by
control module. Adding support for these clocks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All users now register platform devices using the ti-aemif driver.
Remove the handcrafted aemif API.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in mityomapl138.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in dm646x-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in da830-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in dm644x-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in dm365-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support board files in the aemif driver. Register a platform
device instead of using the handcrafted API in da850-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now have support for aemif & nand from board files. As an example
add support for nand to da850-hawk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the power-domains property to CPPI 4.1 node.
The CPPI 4.1 DMA driver uses pm_runtime to manage the clocks,
so it needs this property in order to find and enable the clock
properly.
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for RTC mode to low level suspend code. This includes
providing the rtc base address for the assembly code to configuring the
PMIC_PWR_EN line late in suspend to enter RTC+DDR mode.
Note: This patch also fold in left out space parameter for
am33xx_emif_sram_table and am43xx_emif_sram_table
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an argument to the sleep33xx and sleep43xx code to allow us to set
flags to determine which portions of the code get called in order to use
the same code for multiple power saving modes. This patch allows us to
decide whether or not we flush and disable caches, save EMIF context,
put the memory into self refresh and disable the EMIF, and/or invoke
the wkup_m3 when entering into WFI.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reuse DEFINE_SHOW_ATTRIBUTE() macro instead of open coding file
operations followed by custom ->open() callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The asm/module.h header file can not be included standalone, which
breaks the module signing code after a recent change:
In file included from kernel/module-internal.h:13,
from kernel/module_signing.c:17:
arch/arm/include/asm/module.h:37:27: error: 'struct module' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
u32 get_module_plt(struct module *mod, unsigned long loc, Elf32_Addr val);
This adds a forward declaration of struct module to make it all work.
Fixes: f314dfea16 ("modsign: log module name in the event of an error")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
This enables the on-module ONFI conformant NAND flash.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic controller device tree node to be extended by
individual boards. Use the assigned-clocks mechanism to set
NDFLASH clock to a sensible default rate of 150MHz.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Colibri-T20 can come in 256 MB RAM (with 512 MB NAND) or 512 MB RAM
(with 1024 MB NAND) flavors. Both of them will use the same DTSI
expecting the bootloader to do the fixup of /memory node. However in
case it does not happen, let's stay on safe side by limiting the memory
to 256 MB for both versions of Colibri-T20.
Rename to remove the unnecessary memory size from the device tree file
name. While at it, also follow the typical Toradex SoC, module, carrier
board hierarchy.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove unneeded address/size cells properties and unit addresses to fix
DTC warnings like:
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (unit_address_vs_reg):
/i2c@7000d000/stmpe811@41/stmpe_touchscreen@0: node has a unit name, but no reg property
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (avoid_unnecessary_addr_size):
/i2c@7000d000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the usage of skeleton.dtsi because it was deprecated since commit
9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated").
It also allows later to fix DTC warnings for missing unit name in
/memory nodes.
Compiled DTBs are the same as before this commit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This pull request brings in a board DT for the Raspberry Pi Compute
Module and its I/O board, the Pi3's PMU node, and the display's
transposer block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's a standard ARM architected timer that was simply missed when
initially adding this .dtsi file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently, the USB 3.0 PHY in bcm5301x.dtsi uses platform driver which
requires register range "ccb-mii" <0x18003000 0x1000>. This range
overlaps with MDIO cmd and param registers (<0x18003000 0x8>).
Essentially, the platform driver partly acts like a MDIO bus driver,
hence to use of this register range.
In some Northstar devices like Linksys EA9500, secondary switch is
connected via external MDIO. The only way to access and configure the
external switch is via MDIO bus. When we enable the MDIO bus in it's
current state, the MDIO bus and any child buses fail to register because
of the register range overlap.
On Northstar, the USB 3.0 PHY is connected at address 0x10 on the
internal MDIO bus. This change moves the usb3_phy node and makes it a
child node of internal MDIO bus.
Thanks to Rafał Miłecki's commit af850e14a7 ("phy: bcm-ns-usb3: add
MDIO driver using proper bus layer") the same USB 3.0 platform driver
can now act as USB 3.0 PHY MDIO driver.
Tested on Linksys Panamera (EA9500)
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The transposer block is allowing one to write the result of the VC4
composition back to memory instead of displaying it on a screen.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This only probes on arm64 so far, but hopefully that driver will be
generalized soon.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
CAN2 currently fails on probe as follows:
mcp251x spi1.1: Probe failed, err=19
Fix this by enabling input on pin mux of resp. SPI4 pins.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.
Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.
Fixes: 40431d16ff ("ARM: tegra: enable PCA9546 on Cardhu")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unbinding and rebinding the ARM PMU driver via sysfs leads to a
warning followed by more errors:
WARNING: CPU: 0 PID: 217 at kernel/irq/chip.c:1034 irq_modify_status+0x150/0x16c
..
genirq: Flags mismatch irq 19. 00010c04 (arm-pmu) vs. 00010c04 (arm-pmu)
hw perfevents: unable to request IRQ19 for ARM PMU counters
hw perfevents: /pmu: failed to register PMU devices!
armv7-pmu: probe of pmu failed with error -16
The driver is clearly not designed to be removed. Disable bind/
unbind for this driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The PandaBoard has a user button connected to GPIO. On the ES this is connected
to GPIO 113, on all the other Panda editons this is GPIO 121.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are a few peripherals that generate some extra noise when they
don't have a regulator assigned to them. This patch assigns them to
their actual tps65023 regulator 'vdd_io_reg' (VDCDC2).
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Trapping blocking WFE is extremely beneficial in situations where
the system is oversubscribed, as it allows another thread to run
while being blocked. In a non-oversubscribed environment, this is
the complete opposite, and trapping WFE is just unnecessary overhead.
Let's only enable WFE trapping if the CPU has more than a single task
to run (that is, more than just the vcpu thread).
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The {pmd,pud,pgd}_populate accessors usage have always been a bit weird
in KVM. We don't have a struct mm to pass (and neither does the kernel
most of the time, but still...), and the 32bit code has all kind of
cache maintenance that doesn't make sense on ARMv7+ when MP extensions
are mandatory (which is the case when the VEs are present).
Let's bite the bullet and provide our own implementations. The only bit
of architectural code left has to do with building the table entry
itself (arm64 having up to 52bit PA, arm lacking PUD level).
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The arm and arm64 KVM page tables accessors are pointlessly different
between the two architectures, and likely both wrong one way or another:
arm64 lacks a dsb(), and arm doesn't use WRITE_ONCE.
Let's unify them.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A small collection of fixes, sort of the usual at this point, all for
i.MX or OMAP:
- Enable ULPI drivers on i.MX to avoid a hang
- Pinctrl fix for touchscreen on i.MX51 ZII RDU1
- Fixes for ethernet clock references on am3517
- mmc0 write protect detection fix for am335x
- kzalloc->kcalloc conversion in an OMAP driver
- USB metastability fix for USB on dra7
- Fix touchscreen wakeup on am437x
-----BEGIN PGP SIGNATURE-----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=N/ik
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small collection of fixes, sort of the usual at this point, all for
i.MX or OMAP:
- Enable ULPI drivers on i.MX to avoid a hang
- Pinctrl fix for touchscreen on i.MX51 ZII RDU1
- Fixes for ethernet clock references on am3517
- mmc0 write protect detection fix for am335x
- kzalloc->kcalloc conversion in an OMAP driver
- USB metastability fix for USB on dra7
- Fix touchscreen wakeup on am437x"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Pull crypto fixes from Herbert Xu:
- add missing RETs in x86 aegis/morus
- fix build error in arm speck
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86 - Add missing RETs
crypto: arm/speck - fix building in Thumb2 mode
Some ahash algorithms set .cra_type = &crypto_ahash_type. But this is
redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the .cra_type automatically.
Apparently the useless assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many ahash algorithms set .cra_flags = CRYPTO_ALG_TYPE_AHASH. But this
is redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many shash algorithms set .cra_flags = CRYPTO_ALG_TYPE_SHASH. But this
is redundant with the C structure type ('struct shash_alg'), and
crypto_register_shash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the shash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
arch/arm/plat-samsung/adc.c needs to #include <linux/mod_devicetable.h>
explicitly since that header file was removed from
<linux/platform_device.h> (it wasn't needed there).
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PXA3xx platforms have 56 interrupts that are stored in two ICMR
registers. The code in pxa_irq_suspend() and pxa_irq_resume() however
does a simple division by 32 which only leads to one register being
saved at suspend and restored at resume time. The NAND interrupt
setting, for instance, is lost.
Fix this by using DIV_ROUND_UP() instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g. It belongs to Samsung
Aries devices family.
Initial version have support for:
- sdcard
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Galaxy S phone, also known as
i9000. It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- internal memory
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable few options which are required to boot typical Linux distro. It
was tested by booting ArchLinux ARM from sdcard.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable config options required for Samsung Aries based phones.
ARM_APPENDED_DTB is also needed, because stock bootloader does not
support loading DTB files.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cleanup the config with savedefconfig.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Adds missing interrupt-controller property to gph2 block,
to silence following warnings during build:
/soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
It's reguired by Samsung Aries boards, an S5PV210 based
Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This driver is a simple muxing driver that controls the
I2S's clock input by using syscon/regmap to change the parent.
The available inputs can be peripheral clock and generated clock.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[sboyd@kernel.org: Fix SPDX tag comment style]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
-----BEGIN PGP SIGNATURE-----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=H1MU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap for v4.18-rc cycle
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
* tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Signed-off-by: Olof Johansson <olof@lixom.net>
Some code cares about the SPSR_ELx format for exceptions taken from
AArch32 to inspect or manipulate the SPSR_ELx value, which is already in
the SPSR_ELx format, and not in the AArch32 PSR format.
To separate these from cases where we care about the AArch32 PSR format,
migrate these cases to use the PSR_AA32_* definitions rather than
COMPAT_PSR_*.
There should be no functional change as a result of this patch.
Note that arm64 KVM does not support a compat KVM API, and always uses
the SPSR_ELx format, even for AArch32 guests.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The enabling of the EMAC was reverted as there was an issue on how
to handle the integrated PHY and it was getting close to the release
window (fe45174b72 ("arm: dts: sunxi: Revert EMAC changes")).
When a solution was found, then the changes were restored in
4b236a0fe5 ("arm: dts: sunxi: h3/h5: Restore EMAC changes") and
4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)").
Unfortunately enabling for the Beelink X2 was missed.
This reverts partially commit 6b0e06df5c (Revert "ARM: dts:
sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The ARM trusted foundations code is currently broken in linux-next when
CONFIG_KCOV_INSTRUMENT_ALL is set:
/tmp/ccHdQsCI.s: Assembler messages:
/tmp/ccHdQsCI.s:37: Error: .err encountered
/tmp/ccHdQsCI.s:38: Error: .err encountered
/tmp/ccHdQsCI.s:39: Error: .err encountered
scripts/Makefile.build:311: recipe for target 'arch/arm/firmware/trusted_foundations.o' failed
I could not find a function attribute that lets me disable
-fsanitize-coverage=trace-pc for just one function, so this turns it off
for the entire file instead.
Link: http://lkml.kernel.org/r/20180529103636.1535457-1-arnd@arndb.de
Fixes: 758517202b ("arm: port KCOV to arm")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cros-ec I2C and SPI transport drivers have been moved from MFD
subsystem to platform/chrome, at the same time, the config symbol has
been renamed and lost the MFD_ prefix, so update all configs to the new
config symbol name.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO3x0AAoJEFBXWFqHsHzODGkIAIIJFPOWBYHyxAVLAtqpNTt7
+Yggu9LGe7rhspT+Hi2DocKIEj1Z11x49KJCqxwrEHg+7xyax6d78b1iclCHLRlr
S9jxulipzkBs/neebrhh6cyF8sxA7TPUgXtEMdRJwYygUoZhe9hngTO3jv+xoDky
l1l9zH9gAlAQA1cxN6Z4ZWYDkNS0mYK3e1VzaeyCXsq5GJ1Vm5Qw1ooTE5DL3K1g
5B2Hw057DJvcSwOhIVir/MQR8sAWj1sKYdsCouxrO/ThEyofEAtfn22romcPaGPW
WBOuTNrOrMy6O/+ndMBNJBXeGt1tONL2cjLbrpffaXJYq6m/56efsee9u1u18Vg=
=4Agh
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18, round 2:
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
* tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Select CONFIG_USB_CHIPIDEA_ULPI and CONFIG_USB_ULPI_BUS so that
USB ULPI can be functional on some boards like that use ULPI
interface.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Select CONFIG_USB_CHIPIDEA_ULPI and CONFIG_USB_ULPI_BUS so that
USB ULPI can be functional on some boards like imx51-babbge.
This fixes a kernel hang in 4.18-rc1 on i.mx51-babbage, caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.
To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous patch removed OMAP clock aliases that were perceived
to be unnecessary. Unfortunately, it broke the ethernet on the
am3517-evm. This patch enables the MDIO clock and EMAC clock.
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Cc: stable@vger.kernel.org #4.16+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-evm has a single USB Host port connected to hsusb1.
This patch enables that USB port.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT specifications do not allow the underscore character in alias names.
Replace all underscores in alias names by dashes.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the Bluetooth on the wl1271 available in some models
of the AM3517-SOM from Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Certain models of the AM3517 SOM from Logic PD come with an
integrated WL1271 WiFi. This patch enables the WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cortex M4 part can be started from a boot loader or over
Linux remoteproc framework.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The tsadc is used to read various voltages on the board, so enable it
to be able to read these voltages from userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the label for all LEDs, we made a mistake setting the label names on
all LEDs, where says green should say red, and viceversa, where says red
should be green.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
audio-graph-card is recommended for audio bindings. Let's change to it and
improve the support by adding the Amplifier configuration and the clock
enable control.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Production hardware will go with the DS1339 RTC chip, so replace the old
for the new one and also add the nIRQ pin to be able to properly wakeup
the system from suspend.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board can be either a host, or a peripheral, so set the controller as
OTG mode to reflect this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the pins used by the LCD controller, the panel-info and display-timings
information for the MIDAS displays connected to the board. There are
two displays in the board, and these, are connected to the LCD controller
through a FPGA, so the timings and the resolution is what expects the FPGA,
not the MIDAS displays.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device. The new
method also allows you to specify a reset gpio which is required for
this board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the backlight nodes to improve the support and describe
better how hardware is done. The changes done were:
* Use PWM_POLARITY_INVERTED instead of the hardcoded number.
* Add pinctrl configuration.
* Add the enable gpio definition.
* Add the power supply definition.
* Add more brightness levels.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX6SLL has HW bus auto clock gating function, enable
it by default to save VDD_SOC_IN power, about 5% ~ 20%
saved depends on different use cases.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The default value of 5ms will use GPIO hardware based debounce clocks
that will keep L4PER from idling consuming about extra 30mW.
Use a value of 10ms that is above the hardware debounce maximum of
7.95ms forcing software based debouncing.
This allows droid4 to enter PER retention during idle as long as UARTs
are idled and USB modules unloaded or unbound.
Note that there seems to be a pending issue with having droid 4 enter core
retention during idle where GPIO bank 1 needs to be reset late after init
for some reason to not block core retention. In addition to that, we are
also missing GPIO related PM runtime calls for omap4 that will be posted
separately.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Walleij