There are 5 chip selects per SPI0 and SPI2 and 3 per SPI1. SPI2 needs
to be pinned out to use and by default they are disabled. So keep the
state disabled to reflect default.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add Keystone IRQ controller IP node which allows ARM
CorePac core to receive signals from DSP cores.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add the sdcc nodes to support the SD card controller using pl180
mmci driver. We also add a temporary fixed regulator until the
regulator driver is mainlined.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the sdcc nodes to support the SD card controller using pl180
mmci driver. We also add a temporary fixed regulator until the
regulator driver is mainlined.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch moves Exynos PM domain code to use the new generic PM domain
look-up framework introduced in previous patches, thus also allowing
the new code to be compiled with CONFIG_ARCH_EXYNOS.
This patch was originally submitted by Tomasz Figa when he was employed
by Samsung.
Link: http://marc.info/?l=linux-pm&m=139955336002083&w=2
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add sama5d4 to sama5_defconfig to build kernel booting on both sama5d3 and
samad4.
Note that earlyprintk can only be working for one or the other.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On Rockchip RK3188 SoCs the platform driver emac_rockchip is used. This variant driver
enables this regulator when the device driver is loaded. The phy no longer needs
to be always on.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SoC identification code, kernel uncompress and low level
debugging routines update.
On SAMA5D4, DBGU is at another address AT91_BASE_DBGU2 so another
round of detection is needed. We also had to differentiate with
SAMA5D3 SoC family and rename some variables.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM fixes from Russell King:
"Fixes for ARM, the most notable being the fix from Nathan Lynch to fix
the state of various registers during execve, to ensure that data
can't be leaked between two executables.
Fixes from Victor Kamensky for get_user() on big endian platforms,
since the addition of 8-byte get_user() support broke these fairly
badly.
A fix from Sudeep Holla for affinity setting when hotplugging CPU 0.
A fix from Stephen Boyd for a perf-induced sleep attempt while atomic.
Lastly, a correctness fix for emulation of the SWP instruction on
ARMv7+, and a fix for wrong carry handling when updating the
translation table base address on LPAE platforms"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8149/1: perf: Don't sleep while atomic when enabling per-cpu interrupts
ARM: 8148/1: flush TLS and thumbee register state during exec
ARM: 8151/1: add missing exports for asm functions required by get_user macro
ARM: 8137/1: fix get_user BE behavior for target variable with size of 8 bytes
ARM: 8135/1: Fix in-correct barrier usage in SWP{B} emulation
ARM: 8133/1: use irq_set_affinity with force=false when migrating irqs
ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET
Add the DMA controller node and DMA bindings to the supported devices.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds mipi_phy device node to reset, disable and enable
DSIM and CSIS PHY.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In order to make the number of interrupts configurable, use the new
fancy device management API to add KVM_DEV_ARM_VGIC_GRP_NR_IRQS as
a VGIC configurable attribute.
Userspace can now specify the exact size of the GIC (by increments
of 32 interrupts).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It is now quite easy to delay the allocation of the vgic tables
until we actually require it to be up and running (when the first
vcpu is kicking around, or someones tries to access the GIC registers).
This allow us to allocate memory for the exact number of CPUs we
have. As nobody configures the number of interrupts just yet,
use a fallback to VGIC_NR_IRQS_LEGACY.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far, all the VGIC data structures are statically defined by the
*maximum* number of vcpus and interrupts it supports. It means that
we always have to oversize it to cater for the worse case.
Start by changing the data structures to be dynamically sizeable,
and allocate them at runtime.
The sizes are still very static though.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, devices for SSP ports 1, 2 and 3 are registered as compatible
devices to pxa27x-ssp. While the actual IP core is comparable, there are
some subtle differences which users of the SSP ports address by looking at
the 'type' field.
By registering devices of type 'pxa27x-ssp', this 'type' field is
incorrectly set to PXA27x_SSP which confuses the users.
To fix this, provide specific ssp port plaform devices which use
'pxa3xx-ssp' as driver name, an instantiate them from pxa3xx.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Provide an explicit match string for PXA3xx SSP ports.
Without this match string, SSP0/SSP1/SSP2 in PXA3xxx will be consided as
PXA27x SSP Port.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The vendor prefix was renamed from "mrvl" to "marvell". Follow this
change in the dts file.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
The vendor prefix was renamed from "mrvl" to "marvell". Follow this
change in the dts file.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
DRA74x and DRA72x family of processors vary slightly in the number
of CPUs. So, add different instances of PMU for each of these processor
groups. Further, since the interrupts bypass crossbar and are directly
connected to GIC, mark the dts nodes with relevant information.
Tested with perf utility.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lucas Weaver <l-weaver@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the more common pr_warn.
Other miscellanea:
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We're moving to the dmaengine API, so let's remove the unused
pieces of the omap legacy DMA code to make sure we don't get
any new users for these:
omap_set_dma_color_mode
omap_set_dma_src_index
omap_set_dma_dest_index
omap_dma_unlink_lch
omap_clear_dma
omap_dma_running
omap_dma_set_prio_lch
omap_set_dma_dst_endian_type
omap_set_dma_src_endian_type
omap_get_dma_index
omap_dma_disable_irq
omap_request_dma_chain
omap_free_dma_chain
omap_dma_chain_a_transfer
omap_start_dma_chain_transfers
omap_stop_dma_chain_transfers
omap_get_dma_chain_index
omap_get_dma_chain_dst_pos
omap_get_dma_chain_src_pos
omap_modify_dma_chain_params
omap_dma_chain_status
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to handle errata I688, a page of sram was reserved by doing a
static iotable map. Now that we use gen_pool to manage sram, we can
completely remove all of these static mappings and use gen_pool_alloc()
to get the one page of sram space needed to implement errata I688.
omap_bus_sync will be NOP until SRAM initialization happens.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use drivers/misc/sram.c driver to manage SRAM on all DT only
OMAP platforms (am33xx, am43xx, omap4 and omap5) instead of
the existing private plat-omap/sram.c
Address and size related data is removed from mach-omap2/sram.c
and now passed to drivers/misc/sram.c from DT.
Users can hence use general purpose allocator apis instead of
OMAP private ones to manage and use SRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have panel support for DT based booting,
let's make it usable and enable most things as modules.
Note that omap3 boards need also the ads7847 module for
the panel that we're now changing to a loadable module.
And n900 seems to require setting the brightness via
sysfs for acx565akm/brightness after modprobe of
panel_sony_acx565akm and omapfb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since many omaps run on battery, we should have the battery
drivers enabled. Let's also enable the reset driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some distros are now using systemd, so let's enable most of
what's recommended at:
http://cgit.freedesktop.org/systemd/systemd/tree/README
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add rtc node to both the at91sam9g45 SoC family and the at91sam9m10g45ek board.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DSS related pinmux and display data nodes required to support HDMI
and DVI video out on CM-T54.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the IO chain reconfigure fixed, we can now enable the PMIC
scripts for LDP.
Note that at least on my es3.0 based LDP, the UART seems to be
flakey after wake-up events from off-idle and hangs but eventually
continues.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we have support for this in board-rx51-peripherals.c, let's
add it to the .dts files too.
Note that the reset GPIO will eventually go to the driver.
For now let's just pull it down and skip any further reset
in case the bootloader has configured the MAC address so
NFSroot works.
Also note that after 3430-sdp are using proper GPMC timings
we can remove the tests for smsc,lan91c94 in gpmc.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are external pulls on these lines and enabling the
internal pulls can cause issue. This is because the internal
pulls are parallel with the external pulls. So let's clear
the internal I2C pulls.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.
Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Compared to legacy booting, we don't have wake-up events enabled
for device tree based booting. This means that if deeper idle
states are enabled, the device won't wake up to UART events and
seems like it has hung.
Let's fix that by adding the wake-up interrupt. Note that we
don't need to set the PIN_OFF_WAKEUPENABLE any longer, that's
handled by the wake-up interrupt when the serial driver does
request_irq on it.
Tested with the following on omap3-overo-summit that has the
ES2.1 omap:
#!/bin/bash
uarts=$(find /sys/class/tty/ttyO*/device/power/ -type d)
for uart in $uarts; do
echo 3000 > $uart/autosuspend_delay_ms
done
uarts=$(find /sys/class/tty/ttyO*/power/ -type d)
for uart in $uarts; do
echo enabled > $uart/wakeup
echo auto > $uart/control
done
echo 1 > /sys/kernel/debug/pm_debug/enable_off_mode
# grep -i uart /proc/interrupts
90: 1085 INTC 74 OMAP UART2
338: 5 pinctrl 366 OMAP UART2
# grep ^core_pwrdm /sys/kernel/debug/pm_debug/count
core_pwrdm (ON),OFF:1654,RET:131,INA:39,ON:1825...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.
And also let's enable thermal as explained by Nishant Menon:
Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.
[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.
Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cc824534d4 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.
As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This switches the SAMA5D3 to use the new atmel,sama5d3-pinctrl id that was
added with the drive strength options patch.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: second compatible string kept as at91sam9x5]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The atmel_nand driver is now able to handle the nfc clock, add it to sama5d3.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Declare the SCKC (Slow Clock Configuration) block and its clks.
Make use of the clk32k clk instead of slow_osc where appropriate.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Otherwise the clock for can0 will never get enabled.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: stable@vger.kernel.org # v3.14
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9g20 support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the SSC integrate in at91sam9rl support frame sync length
extension, so switch compatible string to support this feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We set the DMA configuration on USARTs in the SoC DT in (ARM: at91: sama5d3:
add usart dma configurations). As the audio must work with DMA channels, we
reserve some dma channels for audio, or else audio won't work.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: move to the sama5d3xmb.dtsi to cover all board variants]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
do_unexp_fiq() has never been called by any code in the last 10 years,
it's about time it was removed!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces a new default FIQ handler that is structured in a
similar way to the existing ARM exception handler and result in the FIQ
being handled by C code running on the SVC stack (despite this code run
in the FIQ handler is subject to severe limitations with respect to
locking making normal interaction with the kernel impossible).
This default handler allows concepts that on x86 would be handled using
NMIs to be realized on ARM.
Credit:
This patch is a near complete re-write of a patch originally
provided by Anton Vorontsov. Today only a couple of small fragments
survive, however without Anton's work to build from this patch would
not exist. Thanks also to Russell King for spoonfeeding me a variety
of fixes during the review cycle.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds i2c pinctrl DT node for IFC6410 board. It also adds
necessary DT support for i2c eeprom which is present on IFC6410.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds sdcc4 node to enable wlan support on IFC6410
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add support for i2c controller on the DB8074 board. It also adds necessary
DT support for i2c eeprom which is present on DB8074 board.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add a very minimalistic BCM63138 Device Tree include file which
describes the BCM63138 SoC with only the basic set of required
peripherals:
- Cortex A9 CPUs
- ARM GIC
- ARM SCU
- PL310 Level-2 cache controller
- ARM TWD & Global timers
- ARM TWD watchdog
- legacy MIPS bus (UBUS)
- BCM6345-style UARTs (disabled by default)
Since the PL310 L2 cache controller does not come out of reset with
correct default values, we need to override the 'cache-sets' and
'cache-size' properties to get its geometry right.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom BCM63xx DSL SoCs have a different UART implementation for which
we need specially crafted low-level debug assembly code to support. Add
support for this using the standard definitions provided in
include/linux/serial_bcm63xx.h (shared with their MIPS counterparts).
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds basic support for the Broadcom BCM63138 DSL SoC which is
using a dual-core Cortex A9 system. Add the very minimum required code
boot Linux on this SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable both PCIe ports, one of which is connected to an onboard ethernet
chip, whereas the other goes to a miniPCIe slot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, fixed PCIe supply property names in DT]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the PCIe controller device tree node and hook up the PCIe PHY from
the XUSB pad controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a Q8 format 7 inch tablet with an Allwinner A13 SoC.
It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera,
RTL8188-based WiFi, and micro SD slot for external storage.
It is likely made by a subsidiary of Hanns.G (Hannstar).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most if not all boards we've seen have a fixed 5V regulator, which is
the main power supply and/or fixed output of the PMIC.
Add this one to the common regulators DTSI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Recent bootloader versions from Marvell that have DT support and
various other new features remap the internal registers at
0xf1000000. We have already done this change for most of the
development boards from Marvell, and this commit does this change for
the Marvell Armada 370 RD board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1410961539-10388-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The corresponding bug in pm-sh7372.c was fixed in commit
70fe7b2467 ("ARM: shmobile: Do not access sh7372 A4S domain
internals directly").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We are getting "PRM: I/O chain clock line assertion timed out" errors
on early omaps for device tree based booting. This is because we are
unconditionally calling reconfigure_io_chain while legacy booting
has omap3_has_io_chain_ctrl() checks in place in omap_hwmod.c.
For device tree based booting, we are calling reconfigure_io_chain
unconditionally from pinctrl framework. So we need to add a check for
omap3_has_io_chain_ctrl() to avoid the errors for trying to access
a register that does not exist.
For es3.0, the documentation in "4.11.2 Device Off-Mode Configuration"
just mentions PM_WKEN_WKUP[8] bit. For es3.1, there's a new chapter in
documentation for "4.11.2.2 I/O Wake-Up Mechanism" that describes the
PM_WKEN_WKUP[16] ST_IO_CHAIN bit. So PM_WKEN_WKUP[16] bit did not get
added until in es3.1 probaly to fix issues with flakey wake-up events.
We are doing proper checks for ST_IO_CHAIN already in id.c and with
omap3_has_io_chain_ctrl(). For more information, see also commit
b02b917211 ("ARM: OMAP3: PM: fix I/O wakeup and I/O chain clock
control detection").
Let's fix the issue by selecting the right function during init for
reconfigure_io_chain depending on the omap revision. For es3.0 and
earlier we need to just toggle EN_IO. By doing this, we can move the
check for omap3_has_io_chain_ctrl() from omap_hwmod.c to the init code
in prm_3xxx.c. And then we can unconditionally call reconfigure_io_chain.
Thanks to Paul Walmsley and Nishanth Menon for help with debugging the
issue.
Fixes: 30a69ef785 ("ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap")
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just move the code over as it has no dependencies
on arch/arm/ anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP INTC irqchip driver will be moved under
drivers/irqchip/ soon but we still have a dependency
with mach-omap2 when it comes to idle functions.
In order to make it easy to share those function
prototypes with OMAP PM code, we introduce this new
header.
To avoid modifying several board-files and some of
the PM-related code, we just include the new header
from common.h which was already included by all
users of IRQ-related PM code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By moving i2c devices to DT we can clean up
i2c_board_info and fix a problem with moving
INTC to irq domain where IRQs can be renumbered
on each boot.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a copy'n'paste error making the rk3188 emmc pinctrl nodes reference
the pcfg_pull_default setting that is not available on rk3188.
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The host and otg regulator pinctrl settings got swapped, making the host
reference the otg pinctrl and the other way round. The actual pins are
correct (gpio0-3 for host and gpio2-31 for otg).
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
remove all the board files soon, we can remove this one without problem.
If you use this board, please use a DT-enabled at91sam9g20 kernel with
at91-foxg20.dts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>
This defconfig already enables DEBUG_LL and by default DEBUG_LL_UART_NONE
will be selected (but due to some back compability magic I'd like to
remove is not actually honoured). DEBUG_LL_UART_PL01X is a much saner
default.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defconfig already enables DEBUG_LL and by default DEBUG_LL_UART_NONE
will be selected (but due to some back compability magic I'd like to
remove is not actually honoured). DEBUG_LL_UART_PL01X is a much saner
default.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Clark reports a sleeping while atomic bug when using perf.
BUG: sleeping function called from invalid context at ../kernel/locking/mutex.c:583
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
------------[ cut here ]------------
WARNING: CPU: 2 PID: 4828 at ../kernel/locking/mutex.c:479 mutex_lock_nested+0x3a0/0x3e8()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 2 PID: 4828 Comm: Xorg.bin Tainted: G W 3.17.0-rc3-00234-gd535c45-dirty #819
[<c0216690>] (unwind_backtrace) from [<c0212174>] (show_stack+0x10/0x14)
[<c0212174>] (show_stack) from [<c0867cc0>] (dump_stack+0x98/0xb8)
[<c0867cc0>] (dump_stack) from [<c02492a4>] (warn_slowpath_common+0x70/0x8c)
[<c02492a4>] (warn_slowpath_common) from [<c02492f0>] (warn_slowpath_fmt+0x30/0x40)
[<c02492f0>] (warn_slowpath_fmt) from [<c086a3f8>] (mutex_lock_nested+0x3a0/0x3e8)
[<c086a3f8>] (mutex_lock_nested) from [<c0294d08>] (irq_find_host+0x20/0x9c)
[<c0294d08>] (irq_find_host) from [<c0769d50>] (of_irq_get+0x28/0x48)
[<c0769d50>] (of_irq_get) from [<c057d104>] (platform_get_irq+0x1c/0x8c)
[<c057d104>] (platform_get_irq) from [<c021a06c>] (cpu_pmu_enable_percpu_irq+0x14/0x38)
[<c021a06c>] (cpu_pmu_enable_percpu_irq) from [<c02b1634>] (flush_smp_call_function_queue+0x88/0x178)
[<c02b1634>] (flush_smp_call_function_queue) from [<c0214dc0>] (handle_IPI+0x88/0x160)
[<c0214dc0>] (handle_IPI) from [<c0208930>] (gic_handle_irq+0x64/0x68)
[<c0208930>] (gic_handle_irq) from [<c0212d04>] (__irq_svc+0x44/0x5c)
Exception stack(0xe63ddea0 to 0xe63ddee8)
dea0: 00000001 00000001 00000000 c2f3b200 c16db380 c032d4a0 e63ddf40 60010013
dec0: 00000000 001fbfd4 00000100 00000000 00000001 e63ddee8 c0284770 c02a2e30
dee0: 20010013 ffffffff
[<c0212d04>] (__irq_svc) from [<c02a2e30>] (ktime_get_ts64+0x1c8/0x200)
[<c02a2e30>] (ktime_get_ts64) from [<c032d4a0>] (poll_select_set_timeout+0x60/0xa8)
[<c032d4a0>] (poll_select_set_timeout) from [<c032df64>] (SyS_select+0xa8/0x118)
[<c032df64>] (SyS_select) from [<c020e8e0>] (ret_fast_syscall+0x0/0x48)
---[ end trace 0bb583b46342da6f ]---
INFO: lockdep is turned off.
We don't really need to get the platform irq again when we're
enabling or disabling the per-cpu irq. Furthermore, we don't
really need to set and clear bits in the active_irqs bitmask
because that's only used in the non-percpu irq case to figure out
when the last CPU PMU has been disabled. Just pass the irq
directly to the enable/disable functions to clean all this up.
This should be slightly more efficient and also fix the
scheduling while atomic bug.
Fixes: bbd6455937 "ARM: perf: support percpu irqs for the CPU PMU"
Reported-by: Rob Clark <robdclark@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked. TPIDRURO in
particular needs careful treatment. Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.
Similarly, TEEHBR needs to be cleared during exec as well. Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs. Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previous commits that dealt with get_user for 64bit type missed to
export proper functions, so if get_user macro with particular target/value
types are used by kernel module modpost would produce 'undefined!' error.
Solution is to export all required functions.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AUX setting has no effect that's why remove it.
Warning log:
L2C: platform provided aux values match the hardware, so
have no effect. Please remove them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Match the naming pattern of all other SMP ops and rename
zynq_platform_cpu_die --> zynq_cpu_die.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The hotplug code contains only a single function, which is an SMP
function. Move that to platsmp.c where all other SMP runctions reside.
That allows removing hotplug.c and declaring the cpu_die function
static.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avoid races and add synchronisation between the arch specific
kill and die routines.
The same synchronisation issue was fixed on IMX platform
by this commit:
"ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill"
(sha1: 2f3edfd7e2)
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As there is no Power management unit on this board, it is not possible to power
down a core, just WFI is allowed. There is no point to invalidate the cache and
exit coherency.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DDR controller can detect idle periods and leverage low power
features clock stop. When new requests occur, the DDRC resumes
normal operation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the DDR controller to the Zynq devicetree.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is an ISL9305 regulator on the Parallella board, add it to the DT
along with descriptions of all the supplies.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Other R-Car Gen2 SoCs such as r8a7790 and r8a7791 reserve
the top 256 MiB of memory for use with CMA. Adjust the
board-less r8a7794 code to do the same.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Original gpt per clk parent is from ipg_per clk which
may be scaled when system enter low bus mode, as ipg
clk will be lower in low bus mode, to keep system clk
NOT drift, select gpt per clk parent from OSC which
is at fixed freq always.
On i.mx6qdl, add a osc_per clk source for i.mx6q
TO > 1.0 and all i.MX6dl SoC.
On i.mx6sx, just make gpt per clk from OSC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The GW52xx baseboard supports CANbus so we enable it, configure its pinmux
and CAN_STBY gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Follow the conventions for pinctrl:
- grouping pinctrl in logical alphabatized groups
- remove any pinctrl not being used by a driver or needed by user
- move iomuxc to bottom of file for readability
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Follow the convention of configuring padconf for all pins and not leaving
any 0x80000000 to leave them un-configured.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use the gpio contants defined in bindings for active high/low
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Remove aliases that are either not used by bootloader or are provided via
included dtsi files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The general device-tree rule is to not include nodes that do not have a driver
or bindings in a dts/dtsi. Remove the place-holder nodes from the Gateworks
Ventana boards until a time that a driver with proper bindings exists.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This alias is used by U-Boot to enable/disable the regulator depending
on baseboard type.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The spi-mxs driver does not allow full duplex SPI transfers. The
spi-gpio driver may be used as an alternative if this is required.
Make the choice between those drivers easier for the end user by
providing settings for both drivers.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The labels on the spidev nodes are not used and not required, so
remove them. The TX28 supports 3 chipselects on the SPI
interface. Make all those chipselects available to the user.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Passing '0x80000000' to the pin configuration means that kernel will skip the
IOMUXC_SW_PAD_CTL configuration and will use whathever values come from the
bootloader.
Instead of relying on the bootloader setup, let's configure it in the kernel to
have predictable settings.
'0x1b0b0' is the default POR value for all these pins and has also been verified
that the pins are using this value by manually inspecting the IOMUXC_SW_PAD_CTL
registers, so no functional change has been made.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the wa
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@02220000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
imx6sx has the same LCDIF controller IP as in mx28, so add the proper
compatible strings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the i.MX1 APF9328 from Armadeus.
This change is intended to further remove non-DT support for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add the IOMUX setting for the IR input, rather than relying on the
boot loader.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
HummingBoard after rev 2.0 and the production one starting rev 3.0 uses
gpio 3,5 (EIM_DA5 pad) as the gpio infra red receiver input.
Since the original Carrier1 board is obsolete and we are retiring it,
update the DT file for this. This will mean IR reception will not
work on Carrier1 with this DT file.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Initial patch from Rabeeh, but with the electrical properties added.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The i.MX53 has a Cortex-A8 Performance Monitor Unit.
Add it to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds the battery backed real time clock connected to I2C1
to the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the Freescale (Motorola) i.MX1 ADS board.
This change is intended to further remove non-DT support for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add USB support for Freescale Vybrid tower. The USB hosts over-current
protection signal is not connected to the PHY's over- current
protection, hence we need to disable it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add USB support for Colibri VF61 modules. The Colibri standard pinout
defines a pin for USB over-current. However, due to lack of pinmux
options, the USB hosts over-current protection signal of the Colibri
standard could not be connected to the PHY's over-current protection.
Hence we need to disable the over-current functionality of the USB
controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add device tree node for usbmisc which controls the non-core USB
registers. This is required to use the property to disable the over-
current detection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This adds USB PHY and USB controller nodes. Vybrid SoCs have two
independent USB cores which each supports DR (dual role). However,
real OTG is not supported since the OTG ID pin is not available.
The PHYs are located within the anadig register range, hence we need
to change the length of the anadig registers.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ukl: rebase from ancient kernel version]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The preloaded script addresses on imx25 and imx35 are different, so
imx25 is not compatible with imx35-sdma unless a custom firmware is
loaded.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds basic devicetree template for i.MX1 based SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Everything in the PCI specification assumes devices to be
enumerable on startup. This is only possible if they have
power available.
A future improvement may allow this regulator to be switched
off for D3hot and D3cold power states, but there is a lot
of work to do the pcie host controller side for this to work.
To keep things simple always enable the regulator for now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The Colibri VF61 is a module which needs a carrier board to actually
run. Different carrier board have different hardware support, hence
we should reflect this in the device tree files. This patch adds the
Colibri Evaluation Board, which supports almost all peripherals
defined in the Colibri standard.
Also align the compatible naming, file splitting and file naming with
the scheme which was choosen for the Tegra based modules.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rtc isl1208 driver is used by mx6 nitrogen board, so let's enable it by
default.
The fsl sai driver is used by the vf610-twr board, so let's enable it by
default.
simple-audio-card driver is used by the vf610-twr board, so let's enable it by
default.
Generated this patch by doing:
- make imx_v6_v7_defconfig
- make menuconfig and manually select options
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v6_v7_defconfig
,which results in some additional cleanups.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx weim driver is used by some mx27/mx1 boards, so let's enable it by
default.
Generated this patch by doing:
- make imx_v4_v5_defconfig
- make menuconfig and manually select CONFIG_IMX_WEIM
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v4_v5_defconfig
,which results in some additional cleanups.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On i.MX6Q TO > 1.0, i.MX6DL and i.MX6SX, gpt per clock
can be from OSC instead of ipg_per, as ipg_per's rate
may be scaled when system enter low bus mode, to keep
system timer NOT drift, better to make gpt per clock
at fixed rate, here add support for gpt per clock to
be from OSC which is at fixed rate always.
There are some difference on this implementation of
gpt per clock source, see below for details:
i.MX6Q TO > 1.0: GPT_CR_CLKSRC, b'101 selects fix clock
of OSC / 8 for gpt per clk;
i.MX6DL and i.MX6SX: GPT_CR_CLKSRC, b'101 selects OSC
for gpt per clk, and we must enable GPT_CR_24MEM to
enable OSC clk source for gpt per, GPT_PR_PRESCALER24M
is for pre-scaling of this OSC clk, here set it to 8
to make gpt per clk is 3MHz;
i.MX6SL: ipg_per can be from OSC directly, so no need to
implement this new clk source for gpt per.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add gpt_3m clock for i.mx6qdl, as gpt can source clock
from OSC, some i.MX6 series SOCs has fixed divider of
8 for gpt clock, so here add a fix clk of gpt_3m.
i.MX6Q TO1.0 has no gpt_3m option, so force it to be
from ipg_per.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There is a copy&paste error on register offset of pll7_usb_host gate
clock introduced by i.MX6 PLL bypass support patches. The error breaks
the ENET function, because it overwrites the pll6_enet gate bit.
Correct the offset for all i.MX6 clock drivers.
Thanks to Fugang Duan <B38611@freescale.com> for spotting the error.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Each SSI has "ssi", "ssi_ipg" clocks, and they share same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since ENABLE and BYPASS bits of PLLs are now implemented as separate
gate and mux clocks by clock drivers, the code handling these two bits
can be removed from clk-pllv3 driver.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is the same change for imx6sx clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sx.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is the same change for imx6sl clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6q clock driver currently hard-codes all PLL clocks to source
from OSC24M without BYPASS support. The patch adds the missing lvds_in
clock which is mutually exclusive with lvds_gate, and implements BYPASS
and BYPASS_CLK_SRC selection for PLL clocks as per Figure 10-3. Primary
Clock Generation in IMX6DQRM, i.e. both BYPASS_CLK_SRC and BYPASS bits
are implemented as mux clocks, and ENABLE bit of PLL clocks is
implemented as a gate clock after BYPASS mux.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There are a couple of gate clocks are mutually exclusive on i.MX6, i.e.
LVDSCLK1_IBEN and LVDSCLK1_OBEN. They cannot be enabled simultaneously.
This patches adds an exclusive gate clock type specifically for such
case. The clock driver will need to call imx_clk_gate_exclusive() to
register a gate clock with parameter exclusive_mask indicating the mask
of gate bits which are mutually exclusive to this gate clock.
Right now, it only handles the exclusive gate clocks which are defined
in a single hardware register, which is the case we're running into
today. But it can be extended to handle exclusive gate clocks defined
in different registers later if needed.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Each SSI has "ssi", "ssi_ipg" clocks, and they share same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
ASRC has "asrc", "asrc_ipg", "asrc_mem" clocks, and they share
the same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The parent clocks of IMX6SL_CLK_PXP_AXI_SEL and IMX6SL_CLK_EPDC_AXI_SEL
clocks are not the same. So split the epdc_pxp_sels into two different
clock selections 'pxp_axi_sels' and 'epdc_axi_sels'.
Signed-off-by: Fancy Fang <chen.fang@freescale.com>
Signed-off-by: Robby Cai <R63905@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There are three clock for ESAI, esai_extal, esai_ipg, esai_mem. Rename
'esai' to 'esai_extal', 'esai_ahb' to 'esai_mem', and add 'esai_ipg'.
Make the clock for ESAI more clear and align them with imx6sx.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
PLL5 is well suited for being the parent of IMX6SL_CLK_LCDIF_PIX_SEL and
PLL2_PFD for IMX6SL_CLK_LCDIF_AXI_SEL.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Currently csi_lcdif_sels[] is a shared array for the providing the possible
clock parents for csi and lcdif blocks.
This is not correct, as csi and lcdif do not share the same clock parents.
Introduce csi_sels[] for the csi and lcdif_axi_sels[] for the lcdif clocks in
order to describe the parents correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This commit adds PLL7 which is required for USBPHY1. It also adds
the USB PHY and USB Controller clocks and the gates to enable them.
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add cpufreq support for i.MX6SX, using common
i.MX6Q cpufreq driver.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
At the end of the boot process, the clock framework might disable
required main PLL's. So far, this was no issue since drivers
requested clocks, which are descended of the main PLL's (e.g.
pll1_pfd1, which provides the system clock).
To archive the full 500MHz system clock, DDR clock need to be a
descendant of PLL2 rather than PLL1 (DDRC_CLK_SEL set to 0). The
bootloader sets up the clocks accordingly before making use of
DDR at all. However, in Linux, there is no driver using PLL2,
which lead to PLL2 being disabled by the clock framework.
With this patch, we make sure that the main system clock and the
DDR clock are initially enabled and are kept enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds basic devicetree support for i.MX1 based SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add more revision support for the new i.MX6DQ tape-out (TO1.5). This
TO1.5 is the Rev 1.3 as documented in i.MX6DQ data sheet, because TO1.3
and TO1.4 are never revealed.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The interrupt controller used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we don't depend on anyting in the mach-at91 directory, we can just
move the driver to where it belongs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
arch/arm/mach-at91/Kconfig
arch/arm/mach-at91/Makefile
This allows to remove the dependency of the timer driver on mach/hardware.h and
having an hardcoded interrupt number in the driver itself.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In preparation for DT support where panel timings will be described by a
DRM-agnostic video mode, replace the struct drm_mode_modeinfo instance
in the panel platform data with a struct videomode.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
Fixes: 92beaccd8b ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Cc: <stable@vger.kernel.org> #v3.14+
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/1410339341-3372-1-git-send-email-klightspeed@killerwolves.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
drivers/usb/phy/phy-samsung-usb2 driver got replaced by
drivers/phy/phy-samsung-usb2 one. Remove the leftover
USB2 PHY node (EHCI/OHCI USB nodes are using the new one
already) from Exynos5250 dtsi file.
Cc: Mark Brown <broonie@linaro.org>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT nodes for panel-simple "auo,b133htn01" panel.
Add backlight enable pin and backlight power supply for pwm-backlight.
Also, add panel phandle needed by dp to enable display on peach_pi.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since one of the platforms (Armada 370 RD) is now using the gpio-fan
driver, it makes sense to enable it in mvebu_v7_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1410429419-29820-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
For some reason, while all other features are configured built-in, the
LED class support was configured as a module in
mvebu_v7_defconfig. This commit makes it consistent with the other
options, by making this feature built-in.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1410429419-29820-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 RD has a GPIO controlled LED connected on MPP32, so
this commit adds the relevant hardware description to Armada 370 RD
Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1410429419-29820-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 RD platform has a GPIO-controlled fan on MPP8, so this
commit adds the relevant hardware description to Armada 370 RD Device
Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1410429419-29820-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the conversion of boards to use DT to instantiate Distributed
Switch Architecture, nobody volunteered to test. As to be expected,
the conversion was flawed. Testers and access to hardware has now
become available, and this patch hopefully fixes the problems.
dsa,mii-bus must be a phandle to the top level mdio node, not the port
specific subnode of the mdio device.
dsa,ethernet must be a phandle to the port subnode within the ethernet
DT node, not the ethernet node.
Don't pinctrl hog the card detect gpio for mvsdio.
Rename the .dts files to make it clearer which file is for the Z0
stepping and which for the A0 or later stepping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: seugene@marvell.com
Tested-by: Eugene Sanivsky <seugene@marvell.com>
Fixes: e2eaa339af44: ("ARM: Kirkwood: convert rd88f6281-setup.c to DT.")
Fixes: e7c8f3808be8: ("ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DT")
Cc: <stable@vger.kernel.org> #v3.15+
Link: https://lkml.kernel.org/r/1409592941-22244-1-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 356649ab6d ("ARM: dts: rockchip: unuse the slot-node and deprecate
the supports-highspeed for dw-mmc") removed the slots but not the #xx-cells
properties describing the subnodes. Do this now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the controller node, pinctrl settings for the customizable pins
and sort the controllers like on rk3288 as emmc, sdmmc, sdio for
handling convenience.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables both the otg and host port and adds the vbus regulators
on the Radxa Rock board. As we don't have phy support yet, the vbus
regulators are added in always-on mode.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is a remnant from the first i2c driver iteration that seems to have
been forgotten and thus made its way into the dtsi. Remove it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The restart-handler series from Guenter Roeck got accepted recently and
implements among other things also the restart handler in the samsung
watchdog driver and where applicable in the clock drivers. So there is
no need for having the restart callbacks in s3c24xx boards anymore.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit b3205dea8f ("ARM: EXYNOS: Map SYSRAM through generic DT
bindings") introduced local variable boot_reg where boot address from
cpu_boot_reg() call is stored. Re-use it instead calling cpu_boot_reg()
again.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT nodes for ps8622 bridge chip and panel.
Add backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on peach_pit.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT nodes for ptn3460 bridge chip and panel.
Add backlight enable pin and backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on snow.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM irq work IPI support depends on SMP support. That information is
partly known at early boottime. Lets implement
arch_irq_work_has_interrupt() accordingly.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
The Peach Pi board has an Atmel maXTouch trackpad device.
Add the needed Device Tree nodes to support it.
This Device Tree change is based on the Chrome OS 3.8 tree
but adapted to use the mainline Atmel maXTouch DT binding.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Peach Pit board has an Atmel maXTouch trackpad device.
Add the needed Device Tree nodes to support it.
This Device Tree change is based on the Chrome OS 3.8 tree
but adapted to use the mainline Atmel maXTouch DT binding.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The downstream ChromeOS 3.8 kernel sets the clock frequency
for the I2C bus 7 at 400kHz. Do the same change in mainline.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5420 based Peach Pit and the Exynos5800 based Peach Pi
machines have an i2c ISL29018 light sensor. This patch adds the
device nodes needed to support this device.
These DTS snippets were taken from the downstream Chrome OS 3.8
kernel Device Tree for Peach Pit and Pi boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch creates a thermistor fragment carrying the NTC
Thermistor nodes as children of the IIO based ADC.
This fragment is included in exynos5420-peach-pit.dts and
exynos5800-peach-pi.dts.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding regulators for hdmi for peach-pit board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding regulators for HDMI for Peach-pi board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 based Peach Pit and Exynos5800 based Peach Pi boards
uses a Maxim 77802 power management IC to drive regulators and
its Real Time Clock. This patch adds support for this chip.
These are the device nodes and pinctrl configuration that
are present on the Peach pit DeviceTree source file in the
the Chrome OS kernel 3.8 tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWAc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen ARM bugfix from Stefano Stabellini:
"The patches fix the "xen_add_mach_to_phys_entry: cannot add" bug that
has been affecting xen on arm and arm64 guests since 3.16. They
require a few hypervisor side changes that just went in xen-unstable.
A couple of days ago David sent out a pull request with a few other
Xen fixes (it is already in master). Sorry we didn't synchronized
better among us"
* tag 'stable/for-linus-3.17-b-rc4-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: remove mach_to_phys rbtree
xen/arm: reimplement xen_dma_unmap_page & friends
xen/arm: introduce XENFEAT_grant_map_identity
The Brahma-B15's ISAR0 correcty advertises UDIV/SDIV support in both ARM
and Thumb2 modes (CPUID_EXT_ISAR0=02101110), so we don't need to
manually apply this hwcap.
The code in question actually predates the following commit, which made
our hwcaps unnecessary:
commit 8164f7af88
Author: Stephen Boyd <sboyd@codeaurora.org>
Date: Mon Mar 18 19:44:15 2013 +0100
ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the Atmel Micro ASIC platform device and selects it
by default for h3100 and h3600.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
e38361d 'ARM: 8091/2: add get_user() support for 8 byte types' commit
broke V7 BE get_user call when target var size is 64 bit, but '*ptr' size
is 32 bit or smaller. e38361d changed type of __r2 from 'register
unsigned long' to 'register typeof(x) __r2 asm("r2")' i.e before the change
even when target variable size was 64 bit, __r2 was still 32 bit.
But after e38361d commit, for target var of 64 bit size, __r2 became 64
bit and now it should occupy 2 registers r2, and r3. The issue in BE case
that r3 register is least significant word of __r2 and r2 register is most
significant word of __r2. But __get_user_4 still copies result into r2 (most
significant word of __r2). Subsequent code copies from __r2 into x, but
for situation described it will pick up only garbage from r3 register.
Special __get_user_64t_(124) functions are introduced. They are similar to
corresponding __get_user_(124) function but result stored in r3 register
(lsw in case of 64 bit __r2 in BE image). Those function are used by
get_user macro in case of BE and target var size is 64bit.
Also changed __get_user_lo8 name into __get_user_32t_8 to get consistent
naming accross all cases.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the ARM ARMv7, explicit barriers are necessary when using
synchronisation primitives such as SWP{B}. The use of these
instructions does not automatically imply a barrier and any ordering
requirements by the software must be explicitly expressed with the use
of suitable barriers.
Based on this, remove the barriers from SWP{B} emulation.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Minor fixes for amba-clcd and video DT bindings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u5mP
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
"Minor fixes for amba-clcd and video DT bindings"
* tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: ARM CLCD: Fix color model capabilities for DT platforms
video: fix composite video connector compatible string
now that we don't need to support legacy board-files,
we can completely switch over to a linear irq domain
and make use of irq_alloc_domain_generic_chips() to
allocate all generic irq chips for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we don't need the ifdef if we have omap_nr_pending
telling us how many pending registers we have
on current platform. This solves a possible
problem where we could try to handle bogus
interrupts on OMAP2 and OMAP3 if using single
zImage kernel, because we would end up reading
the following pending FIQ register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that variable will tell us how many INTC_PENDING_IRQn
registers we have. It'll be used on a following patch
to cleanup omap_intc_handle_irq() a bit.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we can set our global omap_nr_irqs early on
and drop the extra argument to omap_init_irq().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that was just a no-op wrapper around omap_intc_handle_irq
anyway.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we're calling set_handle_irq() from
init_irq(), we can safely drop all callers to
omap3_intc_handle_irq() and its definition.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
the idea is that board-files won't need to set
.handle_irq on their machine_descs, which lets
us drop a little more pointless code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want .init_irq to call set_irq_handle() for
legacy platforms. Note that this code will also
be dropped once omap2/3 devices are completely
moved to DT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we are now infering number of IRQ lines based
on correct compatible flag, which renders this
binding completely useless.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we don't need that anymore since specific
devices are passing correct compatible flags.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
that way, our intc driver can figure out how
many IRQ lines INTC has.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
so far, only am33xx has 128 lines, all other devices
have only 96.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
with this, we can use a compatible flag to figure
out how many irq lines are wired up, no need for
our TI-specific ti,intc-size binding.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
now we can safely drop those fields from our machine_desc.
While at that, also drop the now unused omap_intc_of_init()
definition.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IRQCHIP_DECLARE macro is used to declare the same
of_device_id structure for irqchips, it's just
a helper. No functional changes.
Note that we're temporarily including irqchip.h
with its full path, until we move this driver
to drivers/irqchip/.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this will let us drop .handle_irq and .init_irq fields
from our generic machine_descs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
nobody uses that function outside of this file,
so we don't need to expose it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove ifdef around omap3 INTC support. This
will make it easier to reuse code for PM.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_intc_handle_irq now had an unnecessary
base_addr argument. Let's remove it and fix
all callers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
an almost blind conversion from readl_relaxed
to our newly introduced intc_readl().
While at that, also remove some hardcoded
register addresses.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this will cache number of irqs. Also in preparation
for removal of irq_banks array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a single bank in that array, this patch
is in preparation to remove that array. It just
shifts everything to a new set of functions
for register IO while also removing old ones.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is in preparation for removing the pointless
irq_banks array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The definition
static const char *omap3_boards_compat[] __initconst = {
defines a changable array of constant strings. That is you must not do:
*omap3_boards_compat[0] = 'f';
but
omap3_boards_compat[0] = "another string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the restart code has been merged in the watchdog driver, we don't need
the restart code in the mach-sunxi directory anymore.
Remove it entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The sub-mailbox devices are added to the Mailbox DT nodes on
OMAP2420, OMAP2430, OMAP3, AM33xx, AM43xx, OMAP4 and OMAP5
family of SoCs. This data represents the same mailboxes that
used to be represented in hwmod attribute data previously.
The node name is chosen based on the .name field of
omap_mbox_dev_info structure used in the hwmod data.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the rbtree used to keep track of machine to physical mappings:
the frontend can grant the same page multiple times, leading to errors
inserting or removing entries from the mach_to_phys tree.
Linux only needed to know the physical address corresponding to a given
machine address in swiotlb-xen. Now that swiotlb-xen can call the
xen_dma_* functions passing the machine address directly, we can remove
it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Denis Schneider <v1ne2go@gmail.com>
xen_dma_unmap_page, xen_dma_sync_single_for_cpu and
xen_dma_sync_single_for_device are currently implemented by calling into
the corresponding generic ARM implementation of these functions. In
order to do this, firstly the dma_addr_t handle, that on Xen is a
machine address, needs to be translated into a physical address. The
operation is expensive and inaccurate, given that a single machine
address can correspond to multiple physical addresses in one domain,
because the same page can be granted multiple times by the frontend.
To avoid this problem, we introduce a Xen specific implementation of
xen_dma_unmap_page, xen_dma_sync_single_for_cpu and
xen_dma_sync_single_for_device, that can operate on machine addresses
directly.
The new implementation relies on the fact that the hypervisor creates a
second p2m mapping of any grant pages at physical address == machine
address of the page for dom0. Therefore we can access memory at physical
address == dma_addr_r handle and perform the cache flushing there. Some
cache maintenance operations require a virtual address. Instead of using
ioremap_cache, that is not safe in interrupt context, we allocate a
per-cpu PAGE_KERNEL scratch page and we manually update the pte for it.
arm64 doesn't need cache maintenance operations on unmap for now.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Denis Schneider <v1ne2go@gmail.com>
The flag tells us that the hypervisor maps a grant page to guest
physical address == machine address of the page in addition to the
normal grant mapping address. It is needed to properly issue cache
maintenance operation at the completion of a DMA operation involving a
foreign grant.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Denis Schneider <v1ne2go@gmail.com>
This patch adds dma support in both sdcc1 and sdcc3 device node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds support to SD card controller using generic pl180 mmci driver.
This patch also adds temporary fixed regulator to get it going till the actual
regulator is mainlined.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the mmcc node so that we can probe and use the multimedia
clocks on apq8064.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds DT support to configure GPIO_78 as function ps_hold
on apq8064.
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds device tree nodes to support pinctrl for apq8064 SOC
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds the TLMM node for the APQ8084 platform.
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add basic support for the IFC6540 single-board computer boards, that are
based on the APQ8084 SoC. This patch adds the initial device tree and the
neccessary nodes required for enabling the serial port and eMMC.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the PMIC and the sub-devices that are currently supported in
the kernel to the DT.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the PMIC and the sub-devices that are currently supported in
the kernel to the DT.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The ISS encoding for an exception from a Data Abort has a WnR
bit[6] that indicates whether the Data Abort was caused by a
read or a write instruction. While there are several fields
in the encoding that are only valid if the ISV bit[24] is set,
WnR is not one of them, so we can read it unconditionally.
Instead of fixing both implementations of kvm_is_write_fault()
in place, reimplement it just once using kvm_vcpu_dabt_iswrite(),
which already does the right thing with respect to the WnR bit.
Also fix up the callers to pass 'vcpu'
Acked-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
using LVDS channel 1 on an i.MX53 leads to following error:
imx-ldb 53fa8008.ldb: unable to set di0 parent clock to ldb_di1
This comes from imx_ldb_set_clock with mux = 0. Mux parameter must be "1" for
reparenting di1 clock to ldb_di1. The value of the mux param comes from device
tree port settings.
On i.MX5, the internal two-input-multiplexer is used. Due to hardware limitations,
only one port (port@[0,1]) can be used for each channel (lvds-channel@[0,1],
respectively)
Documentation update suggested by Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Fixes: e05c8c9a79 ("ARM: dts: imx53: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We should be able to talk to the PMIC at 400kHz. No need to talk at
the slow 100kHz.
As measured by ftrace (with a bunch of extra patches, since cpufreq
for rk808 hasn't landed yet):
before this change: cpu0_set_target() => ~500us
after this change: cpu0_set_target() => ~300us
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by Addy Ke <addy.ke@rock-chips.com>
Tested-by Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
* Make domain_devices[] static __initdata
* Add and use rmobile_add_devices_to_domain
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5GhR
-----END PGP SIGNATURE-----
Merge tag 'renesas-pm-cleanups-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Pull "Renesas ARM Based SoC PM Cleanups for v3.18" from Simon Horman:
* Make domain_devices[] static __initdata
* Add and use rmobile_add_devices_to_domain
Signed-off-by: Arnd Bergmann <ardn@arndb.de>
* tag 'renesas-pm-cleanups-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva legacy: Use rmobile_add_devices_to_domains()
ARM: shmobile: r8a7740: Clean up pm domain table
ARM: shmobile: r8a7740: Use rmobile_add_devices_to_domains()
ARM: shmobile: sh7372: Make domain_devices[] static __initdata
ARM: shmobile: mackerel: Make domain_devices[] static __initdata
The r8a7794 support is always compiled using ARCH_MULTIPLATFORM which
selects USE_OF. So #ifdef CONFIG_USE_OF is unnecessary.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Support for the r8a7794 was recently added.
Enable it in the shmobile_defconfig to increase build coverage.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
LDO8 regulator is used for act led and serial cosole power supply.
Its DT status is declared as "disabled", however the serial console was
functional until Commit 318dbb02b ("regulator: palmas: Fix SMPS
enable/disable/is_enabled") wich properly turns off LDO8 on boot.
Fix serial cosole power supply (and act led) on boot by turning LDO8 on.
Fixes: 318dbb02b ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The nand timings were scaled down by 2 to account for
the 2x rate returned by clk_get_rate(gpmc_fclk).
As the clock data got fixed by [1], revert back to actual
timings (i.e. scale them up by 2).
Without this NAND doesn't work on dra7-evm.
[1] - commit dd94324b98
ARM: dts: dra7xx-clocks: Fix the l3 and l4 clock rates
Fixes: ff66a3c86e ("ARM: dts: dra7: add support for parallel NAND flash")
Cc: <stable@vger.kernel.org> [3.16]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the recent change to the reset function API (commit
7b6d864b48), the mode argument changed from a
char to an enum. lpc23xx_restart() only handles REBOOT_SOFT and REBOOT_HARD,
but the new kernel code emits REBOOT_COLD (0) on reboots now which leads to
lpc32xx simply not rebooting (but halting).
This patch fixes this by just resetting unconditionally as on other platforms
(e.g. mach-bcm2835).
Pulling lpc32xx_watchdog_reset() into lpc23xx_restart() since the while() in
lpc23xx_restart() is part of the procedure anyway and lpc32xx_watchdog_reset()
isn't used anywhere else anymore.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Pull "ARM: LPC32xx: Device tree updates" from Roland Stigge:
This enables ubifs in the lpc32xx defconfig.
* 'lpc32xx/defconfig' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: defconfig update
All the current support of mach-mxt_td60 board can be converted to devicetree.
Remove the board file.
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
OMAP4, OMAP5 and DRA7 share a lot of common logic and data structures.
These have been enabled in the previous patches, however, this also
means that OMAP5 or DRA7 only builds also need to build OMAP4 logic.
Update to reuse OMAP4 logic.
This fixes the 'undefined reference to 'omap4_pm_init_early'' in
OMAP5 or DRA7 only builds.
Fixes: 6af16a1dac ("ARM: DRA7: Add hook in SoC initcalls to enable pm initialization")
Fixes: 628ed47170 ("ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables EMAC Rockchip support on radxa rock boards.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for EMAC Rockchip driver on RK3188 SoCs.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the ARM variant for 314beb9bca ("x86: bpf_jit_comp: secure bpf
jit against spraying attacks").
It is now possible to implement it due to commits 75374ad47c ("ARM: mm:
Define set_memory_* functions for ARM") and dca9aa92fc ("ARM: add
DEBUG_SET_MODULE_RONX option to Kconfig") which added infrastructure for
this facility.
Thus, this patch makes sure the BPF generated JIT code is marked RO, as
other kernel text sections, and also lets the generated JIT code start
at a pseudo random offset instead on a page boundary. The holes are filled
with illegal instructions.
JIT tested on armv7hl with BPF test suite.
Reference: http://mainisusuallyafunction.blogspot.com/2012/11/attacking-hardened-linux-systems-with.html
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a wild mixture of isl, isil, and intersil
compatibles in the kernel. At this point, changing the vendor
symbol to the most often used variant, which is equal to the
NASDAQ symbol, isil, should not hurt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lkml.kernel.org/r/1410167960-554-4-git-send-email-p.zabel@pengutronix.de
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Karicheri Muralidharan