The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself. Eg:
PXA270 standby: "In standby mode, all clocks are disabled except those
for the power manager and the RTC."
PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
and to all peripherals except the RTC."
PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
disabled, except the RTC."
Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming. However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.
Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3. These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Considering that generic.c is getting more and more bloated by device
information, moving that part out side will be much cleaner.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the SSP driver at arch_initcall() time, so it's available
for other drivers to use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. change SSP register definitions from absolute virtual addresses to
offsets
2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define "struct ssp_device" for SSP information, which is requested
and released by function ssp_request()/ssp_free()
2. modify the ssp_init() and ssp_exit() to use the interface
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OSCR is supposed to monotonically increment; however restoring it
to a time prior to OSMR0 may result in it being wound backwards.
Instead, if OSMR0 is within the minimum expiry time, wind OSMR0
forwards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apparantly, the generic time subsystem can accurately emulate periodic
mode via the one-shot support code, so we don't need our own periodic
emulation code anymore. Just ensure that we build support for one shot
into the generic time subsystem.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux has framebuffer backlight support infrastructure which should
be used to expose backlight attributes. Mainstone should use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the PIC is attached to UART1, it doesn't need a kernel device driver
of its own; but powering off is something that the kernel should do, so
this patch forcefully configures the UART1 for 19200 baud and sends the
character that tells the PIC to cut the power.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Orion/MV88F5182 based QNAP
TS-109/TS-209 NAS device. The driver for the S-35390A RTC
chip on this board has been submitted to LKML separately.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Oyvind Repvik <repvik@kynisk.com>
Tested-by: Tim Ellis <timtimred@foonas.org>
Tested-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
The Orion I2C controller is the same one used in the Discovery
family (MV643XX). This patch include the common platform_device
stuff according to the existing i2c_mv64xxx.c conventions.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
The D-Link DNS-323 uses a M41T80 RTC chip, so enable this driver in
the Orion defconfig.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Basic selections for Orion machines
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
With this patch USB, SATA (via sata_mv), Ethernet, RTC, LEDs and NOR Flash
work.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
add MV88F5181 support bits required by D-link DNS-323 patch
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only serial, NOR, NAND, PCI and Ethernet is activated at the moment.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
serial, NOR, PCI and Ethernet is activated at the moment.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Orion Ethernet port is the same port used in the Discovery
family (MV643XX). This patch include the common platform_device
stuff according to the existing mv643xx_eth conventions.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Orion edge sensitive GPIO IRQs.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
CC: Thomas Gleixner <tglx@linutronix.de>
This is a pre-requisite for implementing proper hardware accelerated
GPIO LED flashing, and since we want proper locking, it's sensible to provide
the orion specific orion_gpio_set_blink() implementation within
mach-orion/gpio.c. The functions orion_gpio_set_blink() and gpio_set_value()
implicitly turn off each others state.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Orion has fully programable address map. There's a separate address
map for each of the device _master_ interfaces, e.g. CPU, PCI, PCIE, USB,
Gigabit Ethernet, DMA/XOR engines, etc.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for PCI and PCI-E controllers in the
Orion, Orion-NAS and Orion2.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Marvell Orion is a family of ARM SoCs with a DDR/DDR2 memory
controller, 10/100/1000 ethernet MAC, and USB 2.0 interfaces,
and, depending on the specific model, PCI-E interface, PCI-X
interface, SATA controllers, crypto unit, SPI interface, SDIO
interface, device bus, NAND controller, DMA engine and/or XOR
engine.
This contains the basic structure and architecture register definitions.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This enables the usage of some old Feroceon cores
for which the CPU ID is equal to the ARM926 ID.
Relevant for Feroceon-1850 and old Feroceon-2850.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cache replacement policy on the Feroceon core doesn't guarantee
that reading through a linear chunk of memory flushes the entire cache.
This is however what the default method for ARMv5TE cores does.
Although the Feroceon is an ARMv5TE core, it implements the same
cache handling instructions as the ARMv5TEJ cores, and must use it for
proper cache flush.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The default ARMv4 method consisting of reading through some memory
area isn't compatible with the cache replacement policy of some
ARMv5TEJ compatible cache implementations. It is also a bit wasteful
when a dedicated instruction can do the needed work optimally.
It is hard to tell if all ARMv5TEJ cores will support the used CP15
instruction, but at least all those implementations Linux currently
knows about (ARM926 and ARM1026) do support it.
Tested on an OMAP1610 H2 target.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Tested-by: George G. Davis <gdavis@mvista.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Feroceon is a family of independent ARMv5TE compliant CPU core
implementations, supporting a variable depth pipeline and out-of-order
execution. The Feroceon is configurable with VFP support, and the
later models in the series are superscalar with up to two instructions
per clock cycle.
This patch adds the initial low-level cache/TLB handling for this core.
Signed-off-by: Assaf Hoffman <hoffman@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91CAP9A-DK Evaluation Kit board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the udc pullup is enabled by default on boot. If the device
is connected to a host at this time, the host starts the negotiation
before the udc/gadget driver is ready to handle it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add NEW_LEDs support for the following boards:
- Cogent CSB337
- Atmel AT91RM9200-DK
- Atmel AT91RM9200-EK
- Atmel AT91SAM9263-EK
Mostly based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to errata regarding the handling of SPI CS0 on the AT91RM9200, the
atmel_spi driver drives CS0 from the SPI controller and not as a GPIO
pin.
We therefore need to configure CS0 for use by the controller
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the 3 GPIO-connected buttons on the CSB300 board.
Based on wakeup testing code from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.
Patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Map the complete memory region (SZ_256M) as is done on the other AT91
processors.
The SMC_SMARTMEDIA bit should be set in the EBI controller to enable
the hardware NAND logic.
(Patch from Sascha Erlacher)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace hard-coded DMA mask (0xffffffff) with DMA_BIT_MASK(32) as
defined in dma-mapping.h.
Set "dma_mask" field for the UART platform_devices.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.
For SAM9263, register both RTT peripherals.
[From: David Brownell <dbrownell@users.sourceforge.net>]
Provide platform_resources for RTT peripherals
[From: David Brownell <dbrownell@users.sourceforge.net>]
Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
[From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.
Patch from MaLiK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for STN LCD displays on Atmel AT91SAM9261-based boards.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the at92sam9263ek board, tell the MACB driver the IRQ used
by its PHY. This patch is taken from Andrew Victor's 2.6.23-at91
patchset; it matches board schematics. (But it's currently a NOP
since the MACB driver doesn't yet use PHY irqs.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes HZ configurable on AT91, following the model used on OMAP.
It defaults to a power of two on AT91rm9200 chips, avoiding rounding
errors which come from dividing a 32 KiHz clock to generate scheduler
irqs; and uses 100 on AT91sam926x chips, using MCK/16 (multi-MHZ).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Remy Bhmer <linux@bohmer.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Slight tweaking of the default interrupt priorities (AIC) for the
integrated peripherals on the AT91RM9200, AT91SAM9260, AT91SAM9261 and
AT91SAM9263 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91RM9200 needlessly verifies machine-type numbers of
supported / known platforms and overwrites it for unknown
ones. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add STN LCD support on the Atmel AT91SAM9261-EK board.
Uses a black and white screen from Hitachi: SP06Q002.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a debug interface (if CONFIG_DEBUG_FS is selected) to
display the basic configuration and current state of the GPIO pins on
the Atmel AT91 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is required, in conjunction with the patch submitted to
linux-mtd [1], to access the flash memory device in the GLAN Tank.
Without the patches, the boot log shows
physmap platform flash device: 00080000 at f0000000
...
physmap-flash physmap-flash.0: map_probe failed
whereas with the patches, the boot log shows
physmap platform flash device: 00080000 at f0000000
Found: ST M29W400DB
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
...
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash.0 at offset 0x70000
No RedBoot partition table detected in physmap-flash.0
The change made by this patch is required because the ST M29W400DB
flash memory chip in the GLAN Tank is used in 16 bit bus mode (~BYTE
pin is high when the board is powered on).
[1] http://lists.infradead.org/pipermail/linux-mtd/2008-January/020291.html
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In early 2.6 days stack utilization instrumentation was made
configurable. Seems that arm misses the DEBUG_STACK_USAGE option.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CONFIG variable MTD_OBSOLETE_CHIPS was deleted in commit
ba7cc09c9c.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mach-integrator/pci_v3.c: no need to reference 'irq' arg, its constant
mach-omap1/pm.c: remove extra whitespace
arch/arm/mach-sa1100/ssp.c: remove braces around single C stmt
arch/arm/plat-omap/mcbsp.c:
- remove pointless casts from void*
- make longer lines more readable
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the use of the Advanced SIMD (NEON) extension on
ARMv7. The NEON technology is a 64/128-bit hybrid SIMD architecture
for accelerating the performance of multimedia and signal processing
applications. The extension shares the registers with the VFP unit and
enabling/disabling and saving/restoring follow the same rules. In
addition, there are instructions that do not have the appropriate CP
number encoded, the checks being made in the call_fpe function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the support for VFPv3 (the kernel currently supports
VFPv2). The main difference is 32 double registers (compared to 16).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the VFP support code to run correctly on CPUs
compatible with the common VFP subarchitecture specification (Appendix
B in the ARM ARM v7-A and v7-R edition). It implements support for VFP
subarchitecture 2 while being backwards compatible with
subarchitecture 1.
On VFP subarchitecture 1, the arithmetic exceptions are asynchronous
(or imprecise as described in the old ARM ARM) unless the FPSCR.IXE
bit is 1. The exceptional instructions can be read from FPINST and
FPINST2 registers. With VFP subarchitecture 2, the arithmetic
exceptions can also be synchronous and marked by the FPEXC.DEX bit
(the FPEXC.EX bit is cleared). CPUs implementing the synchronous
arithmetic exceptions don't have the FPINST and FPINST2 registers and
accessing them would trigger and undefined exception.
Note that FPEXC.EX bit has an additional meaning on subarchitecture 1
- if it isn't set, there is no additional information in FPINST and
FPINST2 that needs to be saved at context switch or when lazy-loading
the VFP state of a different thread.
The patch also removes the clearing of the cumulative exception flags in
FPSCR when additional exceptions were raised. It is up to the user
application to clear these bits.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Qualcomm MSM7200A eval board.
Common devices are defined in common.c, to avoid excessive
cut'n'pasting them into other board files.
Signed-off-by: Brian Swetland <swetland@google.com>
- core header files for arch-msm
- Kconfig and Makefiles to enable ARCH_MSM7X00A builds
- MSM7X00A specific arch_idle
- peripheral iomap and irq number definitions
Signed-off-by: Brian Swetland <swetland@google.com>
This patch adds a debug interface (if CONFIG_DEBUG_FS is selected) to
display the basic configuration and current state of the GPIO pins on
the Kendin/Micrel KS8695 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the PCI Host controller integrated in the
Kendin/Micrel KS8695 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new i2c framework to load rtc-rs5c372 for the GLAN Tank.
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* iop13xx, iop33x, iop32x: re-enable the IOP_ADMA driver by default
* iop32x: enable RS5C372 and RTC_CLASS support
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the new GPIO methods in place the old gpio_line_* methods are redundant,
so this patch finally removes the old legacy gpio_line_* wrappers.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Having a both-edge sensitive irq trigger type is required for the
generic gpio-keys input driver; alas the ep93xx does not support
both-edge gpio triggers in hardware, so this patch implements them by
switching edge polarity on each triggered interrupt. This is the same
approach as taken by the Orion SoC both-edge gpio irq support
implementation.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch renumbers the (virtual) GPIO line numbering to have all
irq-capable gpio lines <= EP93XX_GPIO_LINE_MAX_IRQ by swapping the
port f range with the port c range; This simplifies code such as
#define IRQ_EP93XX_GPIO(x) (64 + (((x) + (((x) >> 2) & 8)) & 0x1f))
or
if (line >= 0 && line < 16) {
/* Port A/B */
} else if (line >= 40 && line < 48) {
/* Port F */
}
considerably; in addition to the renumbering this patch also
introduces macro constants EP93XX_GPIO_LINE_MAX_IRQ and
EP93XX_GPIO_LINE_MAX, and replaces most magic numbers by those and
invocations of gpio_to_irq()/irq_to_gpio().
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement new GPIO API for ep93xx platform as defined in Documentation/gpio.txt
and provide transitional __deprecated wrappers for the previous gpio_line_*
functions.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/sys/power should not be a kset, that's overkill. This patch renames it
to power_kset and fixes up all usages of it in the tree.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the code a bit simpler and and gets us one step closer to
deleting the deprecated subsys_attr code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cliff Brake <cbrake@accelent.com>
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename power_subsys to power_kset to catch all users of the variable and
we properly export it so that people don't have to guess that it really
is present in the system.
The pseries code is wierd, why is it createing /sys/power if CONFIG_PM
is disabled? Oh well, stupid big boxes ignoring config options...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add keyboard support on tosa (Sharp Zaurus SL-6000x).
Largely based on patches by Dirk Opfer.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'omap-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
ARM: OMAP1: Fix compile for board-nokia770
ARM: OMAP1: Keymap fix for f-sample and p2-sample
'select' used by config symbol 'INTEL_IOATDMA' refers to undefined symbol 'DCA'
Although drivers/dma is currently the only user future drivers outside of
drivers/dma may select this option so it is better to add this to
arch/arm/Kconfig than move DCA to drivers/dma/Kconfig.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
r2 is not guaranteed to be preserved over a function call, so relying
on it to store the link register over the call to sleep_phys_sp() is
unreliable. Store the link register on the stack instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 09cadedbdc ("Combine
instrumentation menus in kernel/Kconfig.instrumentation") broke ARM
profiling support, since ARM has some extra Kconfig options and doesn't
just use the common OPROFILE/KPROBES config options.
Rather than just revert the thing outright, or add ARM-specific
knowledge to the generic Kconfig.instrumentation file (where the only
and whole point was to be generic, not too architecture-specific), this
just makes ARM not use the generic version, since it doesn't suit it.
So create an arm-specific version of Kconfig.instrumentation instead,
and use that.
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These two instructions exceptionally take a single precision register
as their operand. This means we can't use vfp_get_dm() to read the
register number - we need to use vfp_get_sm() instead. Add a flag to
indicate this exception to the general rule.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add missing i2c_board_info struct for at91rm9200
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suspend/resume on the pxa25x was fairly obviously broken in revision
711be5ccfe.
This patch fixes the damage by adding back the missing code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add proper support for CLOCK_EVT_MODE_RESUME and in the process fix
CLOCK_EVT_MODE_SHUTDOWN so that only the enable bits are toggled for both.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to ARM7TDMI Technical Reference Manual (ARM DDI 0210C) writing
to the DCC data write register coproc dest registers are 1 and 0, not 0
and 1.
ARM920T TRM (ARM DDI 0151C) agrees on that.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change printk to dev_dbg in ITE 8152 driver and remove printk in ITE 8152 ISR.
Move PCI intialization from ->scan to ->preinit method
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM __kuser_cmpxchg routine is meant to implement an atomic cmpxchg
in user space. It however can produce spurious false negative if a
processor exception occurs in the middle of the operation. Normally
this is not a problem since cmpxchg is typically called in a loop until
it succeeds to implement an atomic increment for example.
Some use cases which don't involve a loop require that the operation be
100% reliable though. This patch changes the implementation so to
reattempt the operation after an exception has occurred in the critical
section rather than abort it.
Here's a simple program to test the fix (don't use CONFIG_NO_HZ in your
kernel as this depends on a sufficiently high interrupt rate):
#include <stdio.h>
typedef int (__kernel_cmpxchg_t)(int oldval, int newval, int *ptr);
#define __kernel_cmpxchg (*(__kernel_cmpxchg_t *)0xffff0fc0)
int main()
{
int i, x = 0;
for (i = 0; i < 100000000; i++) {
int v = x;
if (__kernel_cmpxchg(v, v+1, &x))
printf("failed at %d: %d vs %d\n", i, v, x);
}
printf("done with %d vs %d\n", i, x);
return 0;
}
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The lock is acquired with spin_lock_irqsave() and released in the
not-found case with spin_unlock_irqrestore().
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The size passing to memset is wrong. And here we can replace kmalloc with
kzalloc.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AITC code did not allow to start kernel, if bootloader
manipulates with interrupt level mask. The change ensures,
that NIMASK is initialized into correct state and that
interrupts enable registers are cleared.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The incorrect GPIO pins are being initialized for the buttons on the
Atmel AT91SAM9261-EK board. This buggy configuration turns LCD screen
blue...
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91 I2C driver is currently marked as "broken" due to hardware
issues. This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.
This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).
Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The calculation for the Master clock divisor (MDIV) is different on the
SAM9 processors than on the AT91RM9200.
Orignal patch from Sascha Erlacher.
Also use the defined AT91_PMC_PRES instead of hard-coded bitmasks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CKEN_USBHOST should be used instead of CKEN_USB for usb host
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4638/1: pxa: use PXA3xx specific macros to define clks
[ARM] remove useless setting of VM_RESERVED
PXA3xx uses its own clk_pxa3xx_cken_ops, modify the code to use the
PXA3xx specific macros to define its clocks
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (i5k_amb) Convert macros to C functions
hwmon: (w83781d) Add missing curly braces
hwmon: (abituguru3) Identify ABit IP35 Pro as such
hwmon: (f75375s) pwmX_mode sysfs files writable for f75375 variant
hwmon: (f75375s) On n2100 systems, set fans to full speed on boot
hwmon: (f75375s) Allow setting up fans with platform_data
hwmon: (f75375s) Add new style bindings
hwmon: (lm70) Convert semaphore to mutex
hwmon: (applesmc) Add support for Mac Pro 2 x Quad-Core
hwmon: (abituguru3) Add support for 2 new motherboards
hwmon: (ibmpex) Change printk to dev_{info,err} macros
hwmon: (i5k_amb) New memory temperature sensor driver
hwmon: (f75375s) fix pwm mode setting
hwmon: (ibmpex.c) fix NULL dereference
hwmon: (sis5595) Split sis5595_attributes_opt
hwmon: (sis5595) Add individual alarm files
hwmon: (w83627hf) push nr+1 offset into *_REG_FAN macros and simplify
hwmon: (w83627hf) hoist nr-1 offset out of show-store-temp-X
hwmon: Add power meter spec to Documentation/hwmon/sysfs-interface
remap_pfn_range() takes care of setting the appropriate VM_*
flags itself; there's no need for callers of remap_pfn_range()
to set VM_RESERVED before it is called.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
One-shot timer mode on PXA has various bugs which prevent kernels
build with NO_HZ enabled booting. They end up spinning on a
permanently asserted timer interrupt because we don't properly
clear it down - clearing the OIER bit does not stop the pending
interrupt status. Fix this in the set_mode handler as well.
Moreover, the code which sets the next expiry point may race with
the hardware, and we might not set the match register sufficiently
in the future. If we encounter that situation, return -ETIME so
the generic time code retries.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On thecus n2100, the bootloader does not setup fans to run. In order
to protect the user from frying their gear, start up fans on boot.
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This fixes a section error on OMAP when the framebuffer is enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With commit 5984a2fc7e kobject_name() is
correctly being used to access the name field of kobj, but that function
needs a pointer to a kobject, not the kobject itself.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix assignment instead of condition
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resolve:
CC arch/arm/mach-pxa/time.o
arch/arm/mach-pxa/time.c: In function `pxa_osmr0_set_mode':
arch/arm/mach-pxa/time.c:154: warning: enumeration value `CLOCK_EVT_MODE_RESUME' not handled in switch
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jon Eibertzon writes:
> We have noticed that the I-cache is disabled while waiting for
> interrupt in cpu_arm926_do_idle in arch/arm/mm/proc-arm926.S
> and we are curious to know why, because this causes us a great
> performance hit when executing in FIQ-handlers. Is it assumed
> here that every individual FIQ-handler re-enables the I-cache?
The I-cache disable is an errata workaround, so the solution is to
disable FIQs across the section with the I-cache disabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
CC arch/arm/mach-netx/xc.o
arch/arm/mach-netx/xc.c: In function 'request_xc':
arch/arm/mach-netx/xc.c:192: error: 'struct kobject' has no member named 'name'
arch/arm/mach-netx/xc.c:196: error: 'struct kobject' has no member named 'name'
arch/arm/mach-netx/xc.c:200: error: 'struct kobject' has no member named 'name'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-omap1/built-in.o: In function `h2_init':
board-h2.c:(.init.text+0xbb4): undefined reference to `i2c_register_board_info'
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4630/1: Fix the vector stride of the double vector instruction.
[ARM] 4629/1: Fix VFP emulation code to clear all exception flags of FPEXC
[ARM] 4613/1: pxa300: MFP typo fix
arch/arm/common/dmabounce.c: In function 'dma_map_sg':
arch/arm/common/dmabounce.c:445: error: implicit declaration of function 'sg_page'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The vector stride of the double-precision vector instructions must be changed
to 1-2 from even 2-4, because the double registers numbering has been
changed to 0-15 from even 0-30 by
1356c1948d commit.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All exception flags of the FPEXC register must be cleared before
returning from exception code to user code, including FP2V and OFC.
Signed-off-by: Takashi Ohmasa <ohmasa.takashi@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a typo in MFP address map.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Quoting Randy:
"It seems sad that this patch sources Kconfig.marker, a 7-line file,
20-something times. Yes, you (we) don't want to put those 7 lines into
20-something different files, so sourcing is the right thing.
However, what you did for avr32 seems more on the right track to me: make
_one_ Instrumentation support menu that includes PROFILING, OPROFILE, KPROBES,
and MARKERS and then use (source) that in all of the arches."
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be consistent with the use of attributes in the rest of the kernel
replace all use of __attribute_pure__ with __pure and delete the definition
of __attribute_pure__.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason why the .prepare() and .finish() methods in 'struct
platform_suspend_ops' should take any arguments, since architectures don't use
these methods' argument in any practically meaningful way (ie. either the
target system sleep state is conveyed to the platform by .set_target(), or
there is only one suspend state supported and it is indicated to the PM core
by .valid(), or .prepare() and .finish() aren't defined at all). There also
is no reason why .finish() should return any result.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
Remove magic macros for screen_info structure members
[x86] remove uses of magic macros for boot_params access
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon2 and lcdcon3 register value
from the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds synchronization pulse lenght fields to
the s3c2410fb_display structure and makes use of them
in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds vertical margins values to all
s3c24xx platform.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon3 register from the
s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds margins fields to the s3c2410fb_display
structure. It also sets display type and horizontal
margins in all platform files that use the s3c2410fb
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new structure to describe and handle
more than one panel (display mode) for the s3c2410 framebuffer.
This structure is added after the pxafb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.
This change allows the entire process group to be taken down, rather
than just the one thread.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
The variable CPPFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
This patch replace use of CPPFLAGS with KBUILD_CPPFLAGS all over the
tree and enabling one to use:
make CPPFLAGS=...
to specify additional CPP commandline options.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch provides driver for ITE 8152 PCI bridge.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides core support for CM-X270 platform.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_gpio_mode() is a universal call that fiddles with the GAFR
(gpio alternate function register.) GAFR does not exist on PXA3
CPUs, but instead the alternate functions are controlled via the
MFP support code.
Platforms are expected to configure the MFP according to their
needs in their platform support code rather than drivers. We
extend this idea to the GAFR, and make the gpio_direction_*()
functions purely operate on the GPIO level.
This means platform support code is entirely responsible for
configuring the GPIOs alternate functions on all PXA CPU types.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Switch the tps65010 driver into a "new-style" I2C driver, and convert all
of its in-tree users (board support for OSK, H2, H3) accordingly.
That accounts for most of the board-specific code in this driver; the
rest of that code is now moved into board-specific initcalls.
Also remove some of the many now-superfluous #includes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Newer versions of binutils support --build-id, which adds an ELF
note section called ".note.gnu.build-id" to the output. On the ARM
kernel build, because there is no explicit mention of this section
in the shipped ld script, this section is placed at vaddr 0x00000000
(whereas the normal kernel text/data typically starts at vaddr
0xc0008000), causing the output of objcopy (Image) to produce a 3G+
file.
This patch makes objcopy strip the .note.gnu.build-id section from
the Image file along with all other note sections, which fixes the
build.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch resolves a kexec boot failure that can occur because
no ATAGs are passed in to the kexec'd kernel. Currently the
newly-kexec'd kernel may fail if it requires specific ATAGs, or
it may fail because the fixed memory location at which it expects
to find the ATAGs may contain random data instead of ATAGs.
The patch ensures that any ATAGs passed to the current kernel
at boot time are copied to a static buffer, and are copied back
when kexec copies the new kernel into place. Thus the new
kernel sees the same ATAGs from kexec and the boot loader.
The boot parameters are copied without regard to type, content,
or length -- this patch's scope is limited soley to saving and
restoring a fixed-size block of memory containing the kernel's
boot parameters. Additional functionality to examine, alter, or
replace the ATAGs (using kexec, for example) can be implemented
by manipulating the static buffer containing the preserved ATAGs.
Note: the size of the buffer (1.5KB) is selected to comfortably
hold one of each ATAG type, including a maximum-length command
line and the maximum number of ATAG_MEM structures currently
supported by the kernel. Should an ATAG list exceed that limit,
the list will be silently truncated to that limit (to do other-
wise at that point in the boot process would make a simple
problem exceedingly complicated).
[Note: this is the same patch as 4579, modified to accomodate
the ATAG changes introduced in 2.6.23]
Signed-off-by: Mike Westerhof <mwester at dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
consistent_sync() is used to handle the cache maintainence issues with
DMA operations. Since we've now removed the misuse of this function
from the two MTD drivers, rename it to prevent future mis-use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the Cirrus Logic EDB9307, an evaluation
board based on the Cirrus Logic EP9307 SoC, which features amongst
other things 64M RAM, 32M NOR flash, 3 USB host ports, audio in/out,
two serial ports and a 10/100 ethernet interface.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IRQ numbers of the CF and SDI interface on the S3C2412
and S3C2413. Add support to handle these IRQs properly and
ensure that the SDI controller platform device is correctly
renumbered.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a consequence registers are now accessed with __raw_{read,write}[bl].
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Up to now only board-a9m9750dev.c used GPIOs. It just wrote directly into the
corresponding registers. Now it properly reserves the gpio and uses the API
function to configure it.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implementation conforms to the general GPIO API
introduced in 2.6.21.
This patch was signed-of by David Brownell before I exported the functions
using EXPORT_SYMBOL.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FPGA on the a9m9750dev board interrupts the CPU via EXT2. So
to acknowledge any FPGA interrupt IRQ_EXT2 must be acknowledged.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... but the rtc-cmos is rather broken; if PNP is enabled, it assumes
that we have ACPI (!) which is quite bogus on these platforms -
which may have ISAPNP but not ACPI. Something to be solved in the
future.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a magic number before the resume code so
that a bootloader can check that there is an
image to resume to.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The cpu_architecture() function in arch/arm/kernel/setup.c only works
with cores produced by ARM Ltd. The more generic approach is to read
the ID_MMFR0 register and check for the VMSA or PMSA version
supported. With this patch, the ARM11MPCore would be reported as ARMv7
since its MMU is compatible with ARMv7.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Starting with ARMv7-A, conditional execution of undefined instructions
can trigger an exception even if the condition check fails. This patch
modifies the NWFPE support to check the condition before emulating the
instruction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"extern inline" will have different semantics with gcc 4.3.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200.
- Oneshot mode (used for NO_HZ and high res timers) uses the
alarm to emulate a real oneshot timer; the trickiest bit is
how to avoid some lowlevel races. Thanks to Remy Bohmer for
various fixes to this code.
- Tighten up periodic mode support using the PIT.
- Streamline reads of the 32KHz counter. Thanks to Marc Pignat
for some testing results: the CRTR register has *very* odd
behavior. The reread appears to work around stranger glitches
than just getting an old clock value (which would quickly
self-correct).
- Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100),
since that no longer acts correct (time increases too fast).
Note that the at91sam9 and at91x40 chips need other solutions,
since they don't have the same system timer module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by:Remy Bohmer <linux@bohmer.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes section mismatches related to DMA functions.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes section mismatches related to irq functions.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now the drivers are responsible to clear the irq in the respective
device, which seems to be the normal thing to do.
So the ack'ing of the timer irq moved to time.c.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Configuration support for the AT91x40 CPU and EB01 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Makefile build support for the Atmel AT91x40 CPU and EB01 board support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Atmel EB01 board (based on the Atmel AT91x40 CPU).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prototypes for the at91x40 CPU support functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Interrupt setup support for the Atmel AT91x40 CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the timers in the Atmel AT91x40 family of CPUs.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow for configuration of the processor ID for the simplar non-MMU
ARM parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
since both u-boot and blob support passing MACH_TYPE_LUBBOCK to the
kernel, it should be quite safe to remove this
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the generic clock support code to fiddle with the CKEN register
and mark pxa_set_cken() deprecated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using the compile-time constant CLOCK_TICK_RATE, select
the clock tick rate at run time. We organise the selection so that
PXA3 automatically falls out with the right tick rate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous implementation was relying on compile time optimizations
based on a constant clock rate. However, support for different PXA
flavors in the same kernel binary requires that the clock be selected at
run time, so here it is.
Let's move this code to a more appropriate location while at it.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Ensure nRSTOUT is not asserted during or on resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix the following (valid) section warnings:
WARNING: vmlinux.o(.text+0xf7b5c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bridge')
WARNING: vmlinux.o(.text+0xfc5f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_unmap_rom')
WARNING: vmlinux.o(.text+0xfc824): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0xfd6d8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd730): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd788): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfd7e0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'find_free_bus_resource')
WARNING: vmlinux.o(.text+0xfe024): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe0f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
WARNING: vmlinux.o(.text+0xfe17c): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'sys_pciconfig_read')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch enables to define MMC host get_ro() method through platform data.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
These were left out from the board file when merging these drivers,
add them here.
Call GPIO init from the board file as well, since the platform device init
code uses the GPIO API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Removed hwa742 init for now as it needs some clock updates.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mistral-specific:
- Add PWL-driven LCD backlight device
- Apply power to the board even when the LCD isn't configured; things
like EEPROM, temperature sensor, and wakeup switch depend on it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch syncs omap board specific files with linux-omap tree.
Patch consists mostly of driver updates done in linux-omap
tree for drivers not yet in mainline kernel.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds board file and necessary includes for Palm Tungsten|T.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add palmte board config bits for TSC2102 controlled devices. This will
enable touchscreen, audio and APM code to report battery level.
If there are other boards at some point that use a TSC2102, similar
code can be used.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed, so that disabling the SoSSI clock during idle can
be prevented.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support the camera connector on the OSK Mistral add-on board:
- define muxing for both camera controllers
- mux both of them for Mistral
- teach ov9640 glue about mistral powerup/powerdown
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch merges gpmc changes from N800 tree
and adds gpmc_get_fclk_period() to gpmc.h.
Signed-off-by: Kai Svahn <kai.svahn@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add init support for the TUSB6010 EVM board, as connected to H4.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPMC updates:
- bugfixes: wrong/missing flags, omitted write, wrong test
- don't map memory segments starting at zero
- improve debug messaging
- export gpmc_get_fclk_perio]d() since it's needed to calc timings
- expect gpmc_cs_set_timings() caller to have initialized sync vs async
Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove some conflicting declarations in omap2/memory.c so that the
file builds again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update Apollon board init to initialize NAND, USB,
and LEDs. Also configure GPMC memory for smc91x Ethernet.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use virtual addresses directly instead of physical addresses to
avoid having to recalculate the virtual address with every
register access.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The EP93XX_GPIO_LINE_F() macro is supposed to be called with a line
number between 0 and 7, but the current code causes it to get called
with an spuriously offset number range {16..23}.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The l2x0_inv_range() function doesn't handle unaligned addresses
correctly. It's necessary to clean the cache lines that are at the
start and end of the invalidate range, if the addresses are not aligned,
to prevent corruption of other data sharing the same cache line.
Signed-off-by: Rui Sousa <rui.p.m.sousa@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vfp_init() takes care of the condition when CONFIG_VFP=y but no real VFP
device exists. However, when this condition is true, a compiler might
misplace code lines in a way that will break this support. (To be more
specific - fmrx(FPSID) might be executed before vfp_testing_entry
assignment, which will end up with Oops - undefined instruction).
This patch adds a barrier() to guarantee the right execution ordering.
Signed-off-by: Assaf Hoffman
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second GIC asserts a permanent interrupt on Rev.B MPCore platforms.
Disable initialisation of this GIC to avoid unbootable systems.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pins for GPIO should be provided as plain number
build as (GPIO_PORTx + pin_number). But to setup
the output GPIO_GIUS and GPIO_DR have to be specified
in mode to route right value to the pin.
This is a fix, it should go to 2.6.23
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bugfixes for the OSK led support:
- Fix Kconfig merge glitches: Mistral handles idle and timer leds just fine
- Fix pm_suspend() runtime botch: can't sleep, so can't touch tps65010 leds
Improvements:
- Switch sense of Mistral idle led, so idle == off
Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCI driver has not been merged yet, so comment out call to
ks8695_init_pci() for now.
Also fix some incorrectly marked __init and __initdata sections.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Krzysztof Helt <krzysztof.h1@wp.pl>
This patch fixes a typo in architecture constant name.
The kernel for s3c2442 machines does not build without
this fix.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the availability of the iop-adma driver iop platforms can now use
their offload engines for md-raid5 (copy+xor) and net-dma (tcp receive
copy) offload.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused TIF_NOTIFY_RESUME flag for all processor architectures. The
flag was not used excecpt on IA-64 where the patch replaces it with
TIF_PERFMON_WORK.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the jornada720.c file :
* ifdef for CONFIG_SA1100_JORNADA720_SSP since we dont want to include anything not selected in menyconfig.
* add documentation for init for future reference
* change platform driver name from jornada720_mcu ->
jornada_ssp.
* change maintainer in file.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
make ARCH_PXA select GENERIC_CLOCKEVENTS to fix the
building issue due to merge of clockevents based PXA
timer
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
git mv include/asm-arm/arch-s3c2410/regs-ac97.h include/asm-arm/plat-s3c/regs-ac97.h
git mv include/asm-arm/arch-s3c2410/regs-adc.h include/asm-arm/plat-s3c/regs-adc.h
git mv include/asm-arm/arch-s3c2410/regs-iis.h include/asm-arm/plat-s3c24xx/regs-iis.h
git mv include/asm-arm/arch-s3c2410/regs-spi.h include/asm-arm/plat-s3c24xx/regs-spi.h
git mv include/asm-arm/arch-s3c2410/regs-udc.h include/asm-arm/plat-s3c24xx/regs-udc.h
git mv include/asm-arm/arch-s3c2410/udc.h include/asm-arm/plat-s3c24xx/udc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the static maps for the LCD and USB devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the S3C24XX configuration options for the watchdog
boot controls for moving to the arch/arm/plat-s3c moves.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_S3C2410_LOWLEVEL_UART_PORT to be
CONFIG_S3C_LOWLEVEL_UART_PORT as we move to using
plat-s3c for base of S3C operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
git mv commands:
git mv include/asm-arm/arch-s3c2410/iic.h include/asm-arm/plat-s3c/iic.h
git mv include/asm-arm/arch-s3c2410/nand.h include/asm-arm/plat-s3c/nand.h
git mv include/asm-arm/arch-s3c2410/regs-iic.h include/asm-arm/plat-s3c/regs-iic.h
git mv include/asm-arm/arch-s3c2410/regs-nand.h include/asm-arm/plat-s3c/regs-nand.h
git mv include/asm-arm/arch-s3c2410/regs-rtc.h include/asm-arm/plat-s3c/regs-rtc.h
git mv include/asm-arm/arch-s3c2410/regs-serial.h include/asm-arm/plat-s3c/regs-serial.h
git mv include/asm-arm/arch-s3c2410/regs-timer.h include/asm-arm/plat-s3c/regs-timer.h
git mv include/asm-arm/arch-s3c2410/regs-watchdog.h include/asm-arm/plat-s3c/regs-watchdog.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplements arch/arm/mach-pxa/time.c using a clock_event_device based
on OSMR0. Tested on PXA270, linux-2.6.22+arm:pxa patches.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, Linux doesn't generate correct page tables for ARMv6 and
later cores if the cache policy is different from the default one (it
may lead to strongly ordered or shared device mappings). This patch
disallows cache policies other than writeback and the
CPU_[ID]CACHE_DISABLE options only affect the CP15 system control
register rather than the page tables.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the necessary ifdef's to the proc-v7.S code and
defines the v7wbi_tlb_fns macro in pgtable-nommu.h
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The auxiliary control and the L2 auxiliary control registers are
Cortex-A8 specific. They need to be removed from the generic ARMv7
support code.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These patches add full SSP/MCU support for the HP Jornada 720
machine. Its needed to handle keyboard, touchscreen, battery
and backlight/lcd.
The main driver exports functions and the header file exports
the command values. When talking to the MCU the general procedure
is to start MCU, send command (using ssp_inout(command)), the
proper reply is always TXDUMMY. After receiving TXDUMMY you can
send the value you wish pushed (for example brightness level).
End with ssp_end() so the spinlock gets unlocked.
Drivers using this havent been implemented yet, but will shortly.
Signed-off-by: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With this patch, Kconfig only selects CPU_HAS_ASID for the MMU
case. It also corrects the typo in the v6wbi_tlb_fns definition in
pgtable-nommu.h.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __cpu_{clear|copy}_user_page functions are not defined for the
MMU-less case and therefore should not be exported.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If not MMU and not v6K, access to the TLS register has to be
emulated. MMU-less systems do not provide a high page for kuser
helpers.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The background operations of the L2x0 cache controllers are aborted if
another operation is issued on the same or different core. This patch
protects the maintenance operation issuing/polling with a spinlock.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'i' and 'zi' targets short-circuit the dependencies for
'install' and 'zinstall' targets; these are useful for
installing the kernel on platforms which have make but no
compiler installed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is to avoid a compiler warning for overriding the built-in "putc"
function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit d815461c7a in linus tree
converts the rtc-rs5c372 driver to a "new style" i2c driver.
Like commit c00593f6f8, this patch
register the rtc i2c device for the em7210 board.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
the corresponding _suspend functions, thus remove all those ugly
#ifdef .. #endif out of sleep.S
2. move the declarations of those suspend functions to pm.h
note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
operations as follows:
struct pxa_cpu_pm_fns {
int save_size;
void (*save)(unsigned long *);
void (*restore)(unsigned long *);
int (*valid)(suspend_state_t state);
void (*enter)(suspend_state_t state);
}
2. processor specific registers saving and restoring are performed
by calling the corresponding (*save) and (*restore)
3. pxa_cpu_pm_fns->save_size should be initialized to the required
size for processor specific registers saving, the allocated
memory address will be passed to (*save) and (*restore)
memory allocation happens early in pxa_pm_init(), and save_size
should be assigned prior to this (which is usually true, since
pxa_pm_init() happens in device_initcall()
4. there're some redundancies for those SLEEP_SAVE_XXX and related
macros, will be fixed later, one way possible is for the system
devices to handle the specific registers saving and restoring
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update arm to use bitwise types for its VM_FAULT_ constants.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HRM states that is must be done this way ...
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I changed the naming to be more obvious---unfortunately the HRM
doesn't specify these.
Moreover the numbering is changed to be zero indexed as this is more
natural.
Adjust all callers.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
make ns9xxx_ack_irq_functions static and add one include to get declarations
for ns9xxx_map_io and ns9xxx_init_machine.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I must have written the patch introducing support for this machine
deep in the night...
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. for common devices across all the pxa variants, the names
are changed to be:
"pxa_device_xxx"
2. for pxa25x or pxa27x specific devices, the names are
changed to be:
"pxa25x_device_xxx", or
"pxa27x_device_xxx"
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I believe that the following patch is necessary to properly configure
GPIO line configuration for IRQ's which are mapped to a GPIO line >= 8
(without this patch the wrong GPIO is configured as an input.)
Signed-off-by: Tim Harvey <tim_harvey@yahoo.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the AT91RM9200 platform-setup code to use the new atmel_spi
driver (and manually-driven chip-selects), instead of the legacy
AT91-only SPI stack.
The AT91SAM9 processors are already using the atmel_spi driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order for this driver to be shared across the iop architectures the
iop3xx and iop13xx header files are modified to present a common interface
for the iop_wdt driver.
Details:
* iop13xx supports disabling the timer while iop3xx does not. This requires
a few 'compatibility' definitions in include/asm-arm/hardware/iop3xx.h to
preclude adding #ifdef CONFIG_ARCH_IOP13XX blocks to the driver code.
* The heartbeat interval is derived from the internal bus clock rate, so this
this patch also exports the tick rate to the iop_wdt driver.
Cc: Curt Bruns <curt.e.bruns@intel.com>
Cc: Peter Milne <peter.milne@d-tacq.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the basic support for the em7210 board. It is similar to
the iq31244 board and can be found on Intel "Baxter Creek" ss4000e nas.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (44 commits)
i2c: Delete the i2c-isa pseudo bus driver
hwmon: refuse to load abituguru driver on non-Abit boards
hwmon: fix Abit Uguru3 driver detection on some motherboards
hwmon/w83627ehf: Be quiet when no chip is found
hwmon/w83627ehf: No need to initialize fan_min
hwmon/w83627ehf: Export the thermal sensor types
hwmon/w83627ehf: Enable VBAT monitoring
hwmon/w83627ehf: Add support for the VID inputs
hwmon/w83627ehf: Fix timing issues
hwmon/w83627ehf: Add error messages for two error cases
hwmon/w83627ehf: Convert to a platform driver
hwmon/w83627ehf: Update the Kconfig entry
make coretemp_device_remove() static
hwmon: Add LM93 support
hwmon: Improve the pwmN_enable documentation
hwmon/smsc47b397: Don't report missing fans as spinning at 82 RPM
hwmon: Add support for newer uGuru's
hwmon/f71805f: Add temperature-tracking fan control mode
hwmon/w83627ehf: Preserve speed reading when changing fan min
hwmon: fix detection of abituguru volt inputs
...
Manual fixup of trivial conflict in MAINTAINERS file
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per cpu data section contains two types of data. One set which is
exclusively accessed by the local cpu and the other set which is per cpu,
but also shared by remote cpus. In the current kernel, these two sets are
not clearely separated out. This can potentially cause the same data
cacheline shared between the two sets of data, which will result in
unnecessary bouncing of the cacheline between cpus.
One way to fix the problem is to cacheline align the remotely accessed per
cpu data, both at the beginning and at the end. Because of the padding at
both ends, this will likely cause some memory wastage and also the
interface to achieve this is not clean.
This patch:
Moves the remotely accessed per cpu data (which is currently marked
as ____cacheline_aligned_in_smp) into a different section, where all the data
elements are cacheline aligned. And as such, this differentiates the local
only data and remotely accessed data cleanly.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update csb337 board specific init to support "new style" rtc-ds1307 code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new i2c framework to load rtc-rs5c372 for the Thecus N2100.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Voipio Riku <Riku.Voipio@movial.fi>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'ioat-md-accel-for-linus' of git://lost.foo-projects.org/~dwillia2/git/iop: (28 commits)
ioatdma: add the unisys "i/oat" pci vendor/device id
ARM: Add drivers/dma to arch/arm/Kconfig
iop3xx: surface the iop3xx DMA and AAU units to the iop-adma driver
iop13xx: surface the iop13xx adma units to the iop-adma driver
dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines
md: remove raid5 compute_block and compute_parity5
md: handle_stripe5 - request io processing in raid5_run_ops
md: handle_stripe5 - add request/completion logic for async expand ops
md: handle_stripe5 - add request/completion logic for async read ops
md: handle_stripe5 - add request/completion logic for async check ops
md: handle_stripe5 - add request/completion logic for async compute ops
md: handle_stripe5 - add request/completion logic for async write ops
md: common infrastructure for running operations with raid5_run_ops
md: raid5_run_ops - run stripe operations outside sh->lock
raid5: replace custom debug PRINTKs with standard pr_debug
raid5: refactor handle_stripe5 and handle_stripe6 (v3)
async_tx: add the async_tx api
xor: make 'xor_blocks' a library routine for use with async_tx
dmaengine: make clients responsible for managing channels
dmaengine: refactor dmaengine around dma_async_tx_descriptor
...
Adds the platform device definitions and the architecture specific support
routines (i.e. register initialization and descriptor formats) for the
iop-adma driver.
Changelog:
* add support for > 1k zero sum buffer sizes
* added dma/aau platform devices to iq80321 and iq80332 setup
* fixed the calculation in iop_desc_is_aligned
* support xor buffer sizes larger than 16MB
* fix places where software descriptors are assumed to be contiguous, only
hardware descriptors are contiguous for up to a PAGE_SIZE buffer size
* convert to async_tx
* add interrupt support
* add platform devices for 80219 boards
* do not call platform register macros in driver code
* remove switch() statements for compatible register offsets/layouts
* change over to bitmap based capabilities
* remove unnecessary ARM assembly statement
* checkpatch.pl fixes
* gpl v2 only correction
* phys move to dma_async_tx_descriptor
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adds the platform device definitions and the architecture specific
support routines (i.e. register initialization and descriptor formats) for the
iop-adma driver.
Changelog:
* added 'descriptor pool size' to the platform data
* add base support for buffer sizes larger than 16MB (hw max)
* build error fix from Kirill A. Shutemov
* rebase for async_tx changes
* add interrupt support
* do not call platform register macros in driver code
* remove unnecessary ARM assembly statement
* checkpatch.pl fixes
* gpl v2 only correction
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the RTC management over a suspend/resume cycle. As per the
corresponding PXA patch, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows individual CPU support to determine which platform
devices should be registered. Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the RTC management over a suspend/resume cycle. Firstly,
we may not be using the internal RTC for time keeping; some
platforms have an external RTC for this inspite of the PXA having
an internal RTC. Secondly, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.
1. add pxa_init_dma() for dma initialization, the number of channels
are passed in by the argument
2. add a "prio" field to the "struct pxa_dma_channel" for the channel
priority, and is initialized in pxa_init_dma()
3. use a general priority comparison with the channels "prio" field so
to remove the processor specific pxa_for_each_dma_prio macro, this
is not lightning fast as the original one, but it is acceptable as
it happens when requesting dma, which is usually not so performance
critical
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */
1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()
2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. use GPIO_IRQ_mask[] to select those bits of interest, actually
only those "unmasked" GPIO IRQs with their corresponding bits
in GPIO_IRQ_mask[] set to "1" should be checked
2. remove #ifdef PXA_LAST_GPIO > 96 .. #endif, GPIO_IRQ_mask[]
is used to mask out the irrelevant bits, so that even though
the GEDR3 on PXA25x is reserved, it will be masked, and the
following code will never run. Another point is that GPIO85-
GPIO95 bits within GEDR2 will also be masked out on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move the GPIO IRQ initialization code to pxa_init_irq_gpio()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. move low IRQ initialization code to pxa_init_irq_low()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. define PXA_GPIO_IRQ_BASE to be right after the internal IRQs,
and define PXA_GPIO_IRQ_NUM to be 128 for all PXA2xx variants
2. make the code specific to the high IRQ numbers (32..64) to be
PXA27x specific
3. add a function pxa_init_irq_high() to initialize the internal
high IRQ chip, the invoke of this function could be moved to
PXA27x specific initialization code
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. PXA_IRQ_SKIP is defined to be 7 on PXA25x so that the first IRQ
starts from zero. This makes IRQ numbering inconsistent between
PXA25x and PXA27x. Remove this macro so that the same IRQ_XXXXX
definition has the same value on both PXA25x and PXA27x.
2. make IRQ_SSP3..IRQ_PWRI2C valid only if PXA27x is defined, this
avoids unintentional use of these macros on PXA25x
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_prepare() tried to validate the suspend method type. As
noted in previous commits:
eb9289eb209c372d06cee8c9c50269
the checking of the suspend type in the 'prepare' method is the
wrong place to do this; use the 'valid' method instead. This
means that pxa_pm_prepare() can be entirely removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the pm_ops structure into the PXA25x and PXA27x support
files. Remove the old pxa_pm_prepare() function, and rename
the both pxa_cpu_pm_prepare() functions as pxa_pm_prepare().
We'll fix that later.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pxa_pm_finish() does nothing but return zero. The core code
does nothing with this return value, and will not try to call
the finish method in the pm_ops structure if it is NULL.
Therefore, we can remove this useless function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM show_regs() tombstone only partially decodes which ARM ISA was
executing at the time a fault occurred displaying either "(T)" for the
Thumb case or nothing at all for other cases. This patch therefore
explicitly identifies which state the processor is in at the time of
a fault: ARM, Thumb, Jazelle or JazelleEE.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Examines the ATAGS pointer (r2) at boot, and interprets
a nonzero value as a reference to an ATAGS structure. A
suitable ATAGS structure replaces the kernel's command line.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current arch/arm/boot/compressed/head.S code only supports cores
to ARMv6 with the old CPU Id format. This patch adds support for the
new ARMv6 with the new CPU Id and ARMv7 cores that no longer have the
ARMv4 cache operations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
font_acorn_8x8.o was being built in drivers/video/console/ twice
during a build _in the same location_ - once for the kernel proper,
and once for the decompressor. The result is when you came to run an
install target, the kernel was always rebuilt due to this file
apparantly having been built with different compiler arguments.
Solve this by making a local copy at build time in the decompressor's
directory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Driver to control the GPIO pins on the KS8695 processor.
The driver natively supports the Generic GPIO interface.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If MACH_GTWX5715 is set in Kconfig, this code sets the mach id
automatically. Howeber, this means that any IXP4xx kernel which
is setup to support the gtwx5715 board will not successfully boot
on any other board.
If the bootloader sets the wrong mach id, it should be set correctly
by a kernel shim.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes up compiling of the gtwx5715 board setup code,
which has apparently been broken since 2.6.18 and the generic
IRQ changes. In addition it removes some unecessary extern
declarations in the gtwx5715-pci.c file.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides support for the Netgear WG302 v2 and WAG302 v2 AccessPoint series.
This patch relies on the patch "Gateway 7001 series support" minimally, as they only have UART2 connected.
Updated to stay below the 80 char limit in uncompress.h
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides support for the Gateway 7001 AccessPoint series.
Updated to stay below the 80 char limit in uncompress.h
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IXDP425 NAND support (arch specific part).
The generic platform driver that is used by ixdp425 platfrom is already
in upstream kernel in 2.6.22-rc1.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Ruslan Sushko <rsushko@ru.mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tpmi control registers can be accessed on the internal bus via an
address with PCI attributes or IOP attributes (i.e. read-only,
read-write... etc). The sas driver needs access to the iop-attribute
registers for initialization.
Changelog:
* use ARRAY_SIZE for num_resources, Russell King
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support clock event source based on i.MX general purpose
timer in free running timer mode.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for generic input output for MX1 family.
The implementation prevents allocation of one pin
by two users, but does not store pointer to the user
description permanently, because this solution
would have bigger memory overhead.
The simple way to integrate code with per BSP
pins setup and allocation is required else all GPIO
registration checking is useless. The function
imx_gpio_setup_multiple_pins() can be used for this
purpose in future.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the GPIO-connected buttons on the SAM9261-EK board as a
"gpio-keys" platform device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board-specific setup for the LCD on the Atmel AT91SAM9261-EK and
AT91SAM9263-EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the partition layout on the revision B
modules which have large page NAND fitted.
The new partition table accounts for the use of the
128KiB block parts, which means the second partition
on the device is moved to the new boundary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add resources for the AX88796 on the Simtec BAST.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the partition layour used on the
revision B modules which ship with large page NAND
flash as default.
The differnce between the old and new layouts is that
the large page devices use 128KiB blocks, so the
initial loader partition now ends at 128KiB boundary
pushing the begining of partition 1 up. The rest of
the partitions are in the same place as the small page
NAND devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add resources for the SM501 present on the
Simtec Anubis board, including the framebuffer
and the I2C for DDC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the resources necessary for the
AX88796 driver to attach to the AX88796 network
controller fitted on the Simtec Anubis board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support pin multiplexing configurations driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support GPIO driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarino@ru.mvista.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support clock control driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The saved_state member of 'struct dev_pm_info' that's going to be removed
is used in arch/arm/common/locomo.c, arch/arm/common/sa1111.c and
arch/arm/mach-sa1100/neponset.c. Change the code in there to use local
variables for saving the state of devices during suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI syscalls are built on every architecture except X86, but only
a few have ever hooked them up. Use a new Kconfig symbol to save a
couple of kB on the architectures that have never used the syscalls.
Tested on x86 and ia64 only.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't make this dependent on CONFIG_DEBUG_KERNEL - if we hit a WARN_ON
we need the stack trace to work out how we got to that point.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91SAM9260 stopped booting with the recent changes to MM
initialisation - it was asking for a non-aligned virtual address
which caused loops to be non-terminal. Fix this by rounding
virtual addresses down, but remember to include the offset in
the length, and round the length up to the following page.
This means that asking for a mapping of 4K starting at 2K into
a page maps two pages as one would expect.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM Versatile PCI config reads of one byte width have the lowest two
bits of the address cleared and result in reading from a wrong place
in the config space. This change is to use word size accesses like it is done for halfword reads.
Byte reads are used for retrieving the IRQ number of a PCI device and the problem was not exposed until 2.6.20 because the value read was discarded in drivers/pci/setup-irq.c (recently fixed).
Signed-off-by: Andrzej Zaborowski <andrew@openedhand.com>
Acked-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 52ade9b3b9 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues. Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.
at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices. However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose. Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.
This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls. It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all the world is an i386. Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer. Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.
Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely. In fact, ARM already had that, but called it
sys_arm_sync_file_range. Move it to fs/sync.c and rename it, then implement
the needed compatibility routine. And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.
Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the arch/arm/boot/compressed/head.S file, the contents of the
literal pool accumulated during the relocatable code must be dumped
before reloc_end.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the kernel release and version information to the output of
show_regs/oops. Add the CPU PSR register. Avoid using printk
to output partial lines; always output a complete line.
Re-combine the "Control" and "Table + DAC" lines after nommu
separated them; we don't want to waste vertical screen space
needlessly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add calls to oops_enter() and oops_exit() to __die(), so that
things like lockdep know when an oops occurs.
Add suffixes to the oops report to indicate whether the running
kernel has been built with preempt or smp support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the ANUBIS register definitions inline with the
specs and ensure they are registered correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure the CPLD 8bit settings are preserved over a suspend/resume
cycle as the CPU sends a hard-reset at resume time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the watchdog timer to the list of devices
the Osiris registers at startup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the CPLD register definitions to correctly mirror the
documentation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a real section mismatch issue; the test code is thrown away after
initialisation, but if we do not detect the VFP hardware, it is left
hooked into the exception handler. Any VFP instructions which are
subsequently executed risk calling the discarded exception handler.
Introduce a new "null" handler which returns to the "unrecognised
fault" return address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
BUG: using smp_processor_id() in preemptible [00000001] code: opcontrol/427
Resolve this bug by ensuring that we're not using smp_processor_id() in
a preemptable context (by disabling preemption.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When suspending to slow-clock mode, at91_pm_verify_clocks() is called to
ensure that all the clocks are disabled or in the correct state.
This patch replaces the "#warning TODO" messages for the SAM9 processors
with the correct code.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The number of programmable clocks available on the AT91 processors can
differ, therefore do not always display the contents of the PMC_PCKR(0)
.. PMC_PCKR(3) registers (ie, assume there are 4 clocks).
If CONFIG_AT91_PROGRAMMABLE_CLOCKS is enabled, the programmable clocks
will be registered like the other system/peripheral clocks, and the
state of the programmable clocks will be displayed like with the other
clocks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv7 support code requires a valid stack for saving/restoring
registers as the whole D-cache flushing function is more complex. This
patch ensures that the SP register is not corrupted.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are currently using the ARMv6 operations but need to duplicate some
of the code because of the introduction of the new CPU barrier
instructions in ARMv7.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes apparently unnecessary extern declarations in
coyote-pci.c and ixdpg425-pci.c within arch/arm/mach-ixp4xx and
has been compile-tested without producing warnings or errors.
Kernel coding style forbids the use of extern declarations within .c
files.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the undeclared symbols sparse is warning about.
arch/arm/nwfpe/softfloat.c:1727:7: warning: symbol 'float64_to_uint32' was not declared. Should it be static?
arch/arm/nwfpe/softfloat.c:1753:7: warning: symbol 'float64_to_uint32_round_to_zero' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The map_io function does not need to be exported
from this file, and therefore should be declared
static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in the arch/arm/mach-s3c2443/clock.c,
including an bug in initialising the cf clock initialiser
where two values are being set for the ctrlbit.
arch/arm/mach-s3c2443/clock.c:397:12: warning: symbol 'clk_usb_bus_host' was not declared. Should it be static?
arch/arm/mach-s3c2443/clock.c:760:4: error: Initializer entry defined twice
arch/arm/mach-s3c2443/clock.c:761:4: also defined here
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 has an reset-errata where the clock
may cause a glitch switching back to EXTCLK. We
force a switch to EXTCLK before writing the
reset register to force use of the CLKCON sync
logic to properly switch.
Fix problem reported by Matthieu Castet.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix lockdep warnings, caused by 'set_affinity' being called without
the correct locks taken and local interrupts disabled:
=================================
[ INFO: inconsistent lock state ]
2.6.22-rc2 #1
---------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
swapper/1 [HC0[0]:SC0[0]:HE1:SE1] takes:
(irq_controller_lock){++..}, at: [<c002be50>] gic_set_cpu+0x60/0xa0
{in-hardirq-W} state was registered at:
[<c005d9a8>] lock_acquire+0x58/0x6c
[<c0233068>] _spin_lock+0x40/0x50
[<c002c020>] gic_mask_irq+0x2c/0x6c
[<c0069c64>] handle_level_irq+0x11c/0x14c
[<c0020060>] asm_do_IRQ+0x60/0x84
[<c0020d2c>] __irq_svc+0x4c/0xc0
[<c000ed84>] __alloc_bootmem_nopanic+0x74/0x88
[<c000edb0>] __alloc_bootmem+0x18/0x3c
[<c000fa00>] alloc_large_system_hash+0x16c/0x200
[<c00108dc>] inode_init_early+0x5c/0xa4
[<c00106dc>] vfs_caches_init_early+0x24/0xa0
[<c0008e54>] start_kernel+0x220/0x2fc
[<00008078>] 0x8078
irq event stamp: 88438
hardirqs last enabled at (88438): [<c0020dc0>] preempt_return+0x20/0x2c
hardirqs last disabled at (88436): [<c00417bc>] __do_softirq+0xb0/0x138
softirqs last enabled at (88437): [<c0041810>] __do_softirq+0x104/0x138
softirqs last disabled at (88428): [<c0041d9c>] irq_exit+0x68/0x7c
other info that might help us debug this:
no locks held by swapper/1.
stack backtrace:
[<c0025ecc>] (dump_stack+0x0/0x14) from [<c005b1e4>] (print_usage_bug+0x138/0x168)
[<c005b0ac>] (print_usage_bug+0x0/0x168) from [<c005be80>] (mark_lock+0x484/0x6a0)
[<c005b9fc>] (mark_lock+0x0/0x6a0) from [<c005cc48>] (__lock_acquire+0x3c0/0x10c8)
[<c005c888>] (__lock_acquire+0x0/0x10c8) from [<c005d9a8>] (lock_acquire+0x58/0x6c)
[<c005d950>] (lock_acquire+0x0/0x6c) from [<c0233068>] (_spin_lock+0x40/0x50)
[<c0233028>] (_spin_lock+0x0/0x50) from [<c002be50>] (gic_set_cpu+0x60/0xa0)
[<c002bdf0>] (gic_set_cpu+0x0/0xa0) from [<c01b04cc>] (em_route_irq+0x38/0x40)
[<c01b0494>] (em_route_irq+0x0/0x40) from [<c01b04ec>] (em_setup+0x18/0xa4)
[<c01b04d4>] (em_setup+0x0/0xa4) from [<c001570c>] (oprofile_arch_init+0x24/0xe8)
[<c00156e8>] (oprofile_arch_init+0x0/0xe8) from [<c0015640>] (oprofile_init+0x1c/0x64)
[<c0015624>] (oprofile_init+0x0/0x64) from [<c0008a20>] (kernel_init+0x154/0x368)
[<c00088cc>] (kernel_init+0x0/0x368) from [<c003ef34>] (do_exit+0x0/0x904)
oprofile: using arm/mpcore
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an oops in the stacktrace code, caused by improper range checking.
We subtract 12 off 'fp' before testing to see if it's below the low
bound. However, if 'fp' were zero before, it becomes a very large
positive number, causing this test to succeed where it should fail.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the newly introduced __used attribute in place of the deprecated
__attribute_used__. Functionally the same.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This trivial patch updates the nslu2 and nas-100d headers to
remove pointless GPIO defines, and updates nslu2-setup.c
accordingly. In addition minor style cleanups to some comments
are included.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is required as the frequency fixup in nslu2_init does not
run sufficiently early in the boot sequence to take effect. In addition
the dsmg600 setup code behaviour has been improved such that a
'fixup' routine is avoided.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avila and IXDP4xx support were separated in 2.6.21 so this comment
isn't correct any more.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fix:
mm/slab: fix section mismatch warning
mm: fix section mismatch warnings
init/main: use __init_refok to fix section mismatch
kbuild: introduce __init_refok/__initdata_refok to supress section mismatch warnings
all-archs: consolidate .data section definition in asm-generic
all-archs: consolidate .text section definition in asm-generic
kbuild: add "Section mismatch" warning whitelist for powerpc
kbuild: make better section mismatch reports on i386, arm and mips
kbuild: make modpost section warnings clearer
kconfig: search harder for curses library in check-lxdialog.sh
kbuild: include limits.h in sumversion.c for PATH_MAX
powerpc: Fix the MODALIAS generation in modpost for of devices
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add definition for high-speed MMC/SD device and add to SMDK2443
device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reduce the Twrph0 timing slightly to fit on an SMDK2443. This
should still produce valid timings for the NAND devices as it
is still over the smallest device fitted to these boards.
Signed-off-by: Ben Dooks <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King