This behaves exactly in similar manner to basic fixed-factor-clock, but
adds a few properties on top for handling clock hardware autoidling.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for TI divider clock binding, which simply uses
the basic clock divider to provide the features needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
ti_dt_clk_init_provider() can now be used to initialize the contents of
a single clock IP block. This parses all the clocks under the IP block
and calls the corresponding init function for them.
This patch also introduces a helper function for the TI clock drivers
to get register info from DT and append the master IP info to this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some devices require their clocks to be available with a specific
dev-id con-id mapping. With DT, the clocks can be found by default
only with their name, or alternatively through the device node of
the consumer. With drivers, that don't support DT fully yet, add
mechanism to register specific clock names.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM8660
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the multimedia clock controller found on MSM
8960 based platforms. This should allow multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for the global clock controller found on MSM8960
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Reset controllers and clock controllers are combined into one IP
block on Qualcomm chipsets. Usually a reset signal is associated
with each clock branch but sometimes a reset signal is associated
with a handful of clocks. Either way the register interface is
the same; set a bit to assert a reset and clear a bit to deassert
a reset. Add support for these types of resets signals.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for Qualcomm's PLLs (phase locked loops). This is
sufficient enough to be able to determine the rate the PLL is
running at. We can add rate setting support later when it's
needed.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of Qualcomm's clocks can change their parent and rate at the
same time with a single register write. Add support for this
hardware to the common clock framework by adding a new
set_rate_and_parent() op. When the clock framework determines
that both the parent and the rate are going to change during
clk_set_rate() it will call the .set_rate_and_parent() op if
available and fall back to calling .set_parent() followed by
.set_rate() otherwise.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
sirfprima2 and sirfatlas6 are two different SoCs in CSR SiRF series. for
prima2 and atlas6, there are many shared clocks but there are still
some different register layout and hardware clocks, then result in
different clock table.
here we re-arch the driver to
1. clk-common.c provides common clocks for prima2 and atlas6,
2. clk-prima2.h describles registers of prima2 and clk-prima2.c provides
prima2 specific clocks and clock table.
3. clk-atlas6.h describles registers of atlas6 and clk-atlas6.c provides
atlas6 specific clocks and clock table.
4. clk.h and clk.c expose external interfaces and provide uniform entry
for both prima2 and atlas6.
so both prima2 and atlas6 will get support by drivers/clk/sirf.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The composite clock's .determine_rate implementation can call the
underyling .determine_rate callback corresponding to rate_hw or the
underlying .determine_rate callback corresponding to mux_hw. In both
cases we pass in rate_hw, which is wrong. Fixed by passing mux_hw into
the correct callback.
Reported-by: Lemon Dai <dailemon.gl@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSzV2DAAoJEAf03oE53VmQLl0H/2KFQx+lwcg1XWd6Sq05yW7h
PtVKT6bCNZxDXGiUZ1mvZLBkDlVoQn7p35gX+NM05rsad8t9ibdmEutpe4ynPohc
Es5UpQ20txhpzGoDiIIW+pWng+fajtMV1dV8xEC4pf/d4K7HSH8k/tUwZ4GrtaJb
4eUyohznKBHdroavXao1aIuvM+MJvIu2qvxCZZPYDp0LBzTxlHR+ogcCcqO80YSL
dHG2WzbGLr+XMkxpl0bJMF9bxYarg0NsHk+GPqmnOI479rNevptSncbLQRchvwGD
auEAN8I77IwQGUpTuupssKgUrSbOU9JHTwiC2pv8zkaKdoYaIBQVPXCvmyV6kAk=
=KYgN
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
Second cleanup pull-request for 3.14:
- a tiny fix for the recent AT91 CCF implementation
- the switch of one platform to DT with board file removal
* tag 'at91-cleanup2' of git://github.com/at91linux/linux-at91:
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The clks member of the clk_onecell_data structure should
point to a valid clk array (no NULL entries allowed),
and the clk_num should be equal to the number
of elements in the clks array.
The MSTP driver fails to satisfy the above conditions.
The clks array may contain NULL entries if not all
clock-indices are initialized in the device tree.
Thus, if the clock indices are interleaved we end up
with NULL pointers in-between.
The other problem is the driver uses maximum clock index
as the number of clocks, which is incorrect (less than
the actual number of clocks by 1).
Fix the first issue by pre-setting the whole clks array
with ERR_PTR(-ENOENT) pointers instead of zeros; and
use maximum clkidx + 1 as the number of clocks to fix
the other one.
This should make of_clk_src_onecell_get() return the following:
* valid clk pointers for all clocks registered;
* ERR_PTR(-EINVAL) if (idx >= clk_data->clk_num);
* ERR_PTR(-ENOENT) if the clock at the selected index was not
initialized in the device tree (and was not registered).
Changes in V2:
* removed brackets from the one-line for loop
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use clkidx when registering MSTP clocks instead of loop counter
since the value is then used to access the specific clock index bit
in the mstp register.
The issue was introduced by the following commit:
f94859c215 "clk: shmobile: Add MSTP clock support"
Changes in V2:
* none
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If max77686 chip is instantiated from device tree, it is desirable to
have an OF clock provider to allow device tree based look-up of clocks.
This patch adds OF clock provider registration to the clk-max77686
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a prerequisite for further patch adding OF clock provider support to
the driver, this patch changes the driver to store an array of struct
clk * as driver data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch fixes invalid kfree() and adds missing call to clk_unregister()
in error and remove paths in max77686_clk_probe(). While at it, error
handling is also cleaned up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As a preparation for further patches, this patch modifies the clock
registration helper function to return a pointer to the newly registered
clock. No functional change is done to the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The function can simply return 0, without jumping to a separate label,
which does exactly the same. This patch does not introduce any
functional change, just a clean-up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is usually nice to know frequency of a clock, so this patch adds a
.recalc_rate() callback returning rates of provided clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Changing status of clock gates in max77686 requires i2c transfers, which
can sleep, so this is done in prepare and unprepare callbacks. Due to
this, checking whether whether the clock is ungated must be done
in is_prepared() callback as well, for consistency.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The AudioSS block on Exynos 5420 has an additional clock gate for the
ADMA bus clock.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
There is no gate for the PCM clock input to the AudioSS block, so
the parent of sclk_pcm is div_pcm0. Add a clock ID for it so that
we can reference it in device trees.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This allows the input clocks to the Exynos AudioSS block to be
specified via device-tree bindings. Default names will be used
when an input clock is not given.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The Exynos AudioSS clock controller will later be modified to allow
input clocks to be specified via device-tree in order to support
multiple Exynos SoCs. This will introduce a dependency on the core
SoC clock controller being initialized first so that the AudioSS driver
can look up its input clocks, but the order in which clock providers
are probed in of_clk_init() is not guaranteed. Since deferred probing
is not supported in of_clk_init() and the AudioSS block is not the core
controller, we can initialize it later as a platform device.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The patch replaces private enum clock IDs in the driver with macros provided
by the DT header.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Register the APLL rate table so that we can set the APLL rate from
the cpufreq driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Commit 6d9252bd9a (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0B0x
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJSxyvwAAoJEEEQszewGV1zObQQAI7bN0/vmtZkoBbIeoXTAolZ
KTEqf+Gdtlny4AvW4PUeutDRr4zvFHKYo5uBbr9bQFl4S89ke29nLXhyrvJbAWJs
tujyX0mWb38fosEGeVo3YGbDIw9+O3CMRM+zaHyt/yzcHANnPeecpt3dFNheaTKs
W7Axw5YFszpfxs5xQYMrrudbXd6TbsZWSn1pJpNlPvoo8b0HV72ARZNDAM2NO2rY
rOSUzl8MKb0tAW7Nj4D8vLqAtYkjA7lX6sdXQBbqpUyTINR5/35ifW/K74q1miMS
3T5ECbwrW9CHSW2jrTt28knafasAsJKCMdJ9SXu7uzOZogglTuBSw52MIhP2QvHS
mxOXBHkCazCMum4WndLe1ygSigQZR2SAufmjzESsE82RBF2UmkgqR34aaxag9x/X
avxUM/3Opgosa12AD8buSP5NfYqMjvqXzwdNs6YbC1UPqRYIgn9FcJ6cFzkVXoKi
GWgz6Ko6MiR9HVDBqw8uHrIBKuaa3oZ5+jt0x54ZuI3tOxV1wUxR3AcgWQsF2tSN
nPg8GTvZNiEfo6fWSIx7V2H/txFfAj1Z3JG6tFQTfLtE5G7MssxyNitoxZsIeWuB
x1+tnsOQRpBlkUb92LS37ndLJoFfknbCgFUAIgMozntfCRQi/6REWAKGDo0fTOmG
+uN+Q6JMFj62jZ6dgumd
=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
Register both VCO clocks, give per-logical module unique names
to the clocks so we can have several IM-PD1's connected (in
theory). Implement all the fixed-factor clocks as children of
VCO2.
Tested by using the UARTs and the PL181 MMC block on the IM-PD1,
works flawlessly.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we have more than one of these clocks in a system (such as
on the IM-PD1) we need a mechanism to pass a name for the clock.
Refactor to add this as an argument.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add CLK_SET_RATE_PARENT flag to mout_apll clock. This will let us set the
clock rate in the cpufreq driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mout_aclk333_sub mux clock and updates gate clocks from
MFC domain to have it as their parent as specified in SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
According to SoC documentation, input 5 of mout_audio muxes is connected
to xxti (named fin_pll in the driver). This patch corrects defined
parent arrays to match SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch updates mux parent arrays with unpopulated mux inputs, as all
inputs need to be specified in parent arrays passed to
clk_register_mux(), otherwise clk_set_parent() can generate out of bound
accesses to the array.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mux_aclk_200_disp1_sub mux clock, which according to SoC
documentation is the correct parent of DISP1 gate clocks.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch adds mout_aclk266_gscl_sub mux clock and adjusts definitions
of GSCL domain gate clocks to use it as their parent, as specified in
SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch renames all mux clocks to start with mout_ prefix and all div
clocks to start with div_ prefix for consistency with other clocks
already defined this way.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch reorders clock definitions, so they are sorted by register
addresses and bitfield shifts. When at it, blank lines are added to
separate definitions of clocks from different registers.
Overall this should make the driver more readable and reduce the number
of potential conflicts when adding new entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Move reg_save[] into CONFIG_PM_SLEEP dependency block as it is used only
by suspend and resume functions.
This fixes the warning on CONFIG_PM_SLEEP=n:
drivers/clk/samsung/clk-exynos-audss.c:29:22: warning: ‘reg_save’ defined but not used [-Wunused-variable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The sysreg (system register) generates control signals for various blocks
like disp1blk, i2c, mipi, usb etc. However, it gets disabled as an unused
clock at boot-up. This can lead to failures in operation of above blocks,
because they can not be configured properly if this clock is disabled.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Adds gate clock for MDMA0 on Exynos5250 SoC. This is needed to ensure
that the clock is enabled when MDMA0 is used on systems on which
firmware gates the clockby default.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The CLK_GATE_IP_ACP register offset is incorrectly listed making
definition of g2d clock incorrect, which may lead to system failures
when trying to use G2D on systems on which firmware gates this clock
by default. Fix this and the register ordering as well.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The gate clocks for the MFC sysmmus appear to be flipped, i.e.
GATE_IP_MFC[2] gates sysmmu_mfcl and GATE_IP_MFC[1] gates sysmmu_mfcr.
Fix this so that the MFC will start up.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The SRC_MFC register offset was incorrect, which could cause have caused
wrong calculation of rate of sclk_mfc clock, that could in turn lead to
incorrect operation of MFC. This patch corrects it.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Allwinner sunXi SoCs clock changes
This contains the clk driver parts of the "[PATCH v3 00/13] clk: sunxi:
add PLL5 and PLL6 support" series. It adds support for PLL4/5/6 and
mod0 clocks on most sunxi platforms. Additionally, it contains "[PATCH
1/4] clk: sunxi: Allwinner A20 output clock support" (v2) from Chen-Yu
Tsai, which adds support for output clocks present on A20.
This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
The DT nodes should look like
abc_clk: clk@deadbeef {
...
clock-output-names = "abc";
}
But our old DT nodes look like
abc: abc@deadbeef {
...
}
So, let's support both formats, until we can transition everything
to the new, correct one.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
We will be needing this to register a factor clock as parent with leaf
divisors on a single call.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
This was pointed out during the review of the factor patches. Let's
indicate what does that magic 5 mean.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit reworks factors clock registration to be done behind a
composite clock. This allows us to additionally add a gate, mux or
divisors, as it will be needed by some future PLLs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Populate ${DEBUGS_MOUNT_POINT}/clk if CONFIG_DEBUG_FS is set. This
eliminates the extra (annoying) step of enabling the config option
manually.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'break' after 'goto' is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YqMd
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
ARM: dts: Disable I2C controllers by default on Exynos5250
ARM: dts: Leave Exynos5250 SPI controller disabled by default
ARM: dts: Add CODEC MCLK for SMDK5250
ARM: dts: Add device nodes for TMU blocks for exynos5420
ARM: dts: Fix status property of mmc nodes for snow board
ARM: dts: Fix missing spaces after labels for exynos
ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
ARM: dts: Move MCT node to exynos4x12.dtsi
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
Documentation: devicetree: Update Exynos MCT bindings description
ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
ARM: dts: Add SPI nodes to the exynos5420 device tree file
ARM: dts: Add DMA controller node info on Exynos5420
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
ARM: dts: Fix exynos5250-snow's search key to be L_META
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock accuracy is expressed in ppb (parts per billion) and represents
the possible clock drift.
Say you have a clock (e.g. an oscillator) which provides a fixed clock of
20MHz with an accuracy of +- 20Hz. This accuracy expressed in ppb is
20Hz/20MHz = 1000 ppb (or 1 ppm).
Clock users may need the clock accuracy information in order to choose
the best clock (the one with the best accuracy) across several available
clocks.
This patch adds clk accuracy retrieval support for common clk framework by
means of a new function called clk_get_accuracy.
This function returns the given clock accuracy expressed in ppb.
In order to get the clock accuracy, this implementation adds one callback
called recalc_accuracy to the clk_ops structure.
This callback is given the parent clock accuracy (if the clock is not a
root clock) and should recalculate the given clock accuracy.
This callback is optional and may be implemented if the clock is not
a perfect clock (accuracy != 0 ppb).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'clk_si570_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for using emev2 SMU clocks with DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NhhY
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into clk-next-shmobile2
Renesas ARM based SoC Clock updates for v3.14
Add support for using emev2 SMU clocks with DT
The clock was missing CLK_SET_RATE_PARENT flag, which caused rate
setting failures due to inability of reconfiguration of second
divider behind it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extra semicolon is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'vtwm_pll_ops' is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'of_cpu_clk_setup' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_sp810_timerclken_of_get is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
tegra_clk_periph_nodiv_ops is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_frac_ops is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix pmc_clk_ids data type attribute (__initdata -> __initconst).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix building of s2mps11 regulator and clock drivers after renaming
regmap field in struct sec_pmic_dev in commit:
- "mfd/rtc: s5m: Fix register updating by adding regmap for RTC"
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This AT91 specific Kconfig option removed the code that dealt with
programmable clocks. Each AT91 SoC embeds programmable clocks and
there is little gain to remove this code in case that such a clock
is not used.
If this option is not selected, it causes certain drivers to fail
to build. We simply remove this option instead of adding code just
to build a workaround.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The "pcie_xclk" clock is not actually a clock at all, but rather a reset
domain. Now that the custom Tegra module reset API has been removed, we
can remove the definition of any "clocks" that existed solely to support
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
The Tegra CAR module implements both a clock and reset controller. So
far, the driver exposes the clock feature via the common clock API and
the reset feature using a custom API. This patch adds an implementation
of the common reset framework API (include/linux/reset*.h). The legacy
reset implementation will be removed once all drivers have been
converted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch fixes Keystone gate control clock driver initialization path:
1) clk_register_psc() returns error code and not a pure pointer, hence
its return value need to be checked using IS_ERR(clk) macro.
2) Mapped IO memory isn't unmapped in case of errors, hence fix it.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.
Also update the Documentation of bindings to reflect the same.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Fixes cpll control and lock register offset values for Exynos5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_unregister() is currently not implemented and it is required when
a clock provider module needs to be unloaded.
Normally the clock supplier module is prevented to be unloaded by
taking reference on the module in clk_get().
For cases when the clock supplier module deinitializes despite the
consumers of its clocks holding a reference on the module, e.g. when
the driver is unbound through "unbind" sysfs attribute, there are
empty clock ops added. These ops are assigned temporarily to struct
clk and used until all consumers release the clock, to avoid invoking
callbacks from the module which just got removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds common __clk_get(), __clk_put() clkdev helpers that
replace their platform specific counterparts when the common clock
API is used.
The owner module pointer field is added to struct clk so a reference
to the clock supplier module can be taken by the clock consumers.
The owner module is assigned while the clock is being registered,
in functions _clk_register() and __clk_register().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is currently a race condition in the device tree part of clk_get()
function, since the pointer returned from of_clk_get_by_name() may become
invalid before __clk_get() call. E.g. due to the clock provider driver
remove() callback being called in between of_clk_get_by_name() and
__clk_get().
Fix this by doing both the look up and __clk_get() operations with the
clock providers list mutex held. This ensures that the clock pointer
returned from __of_clk_get_from_provider() call and passed to __clk_get()
is valid, as long as the clock supplier module first removes its clock
provider instance and then does clk_unregister() on the corresponding
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add helper functions for the of_clk_providers list locking and
an unlocked variant of of_clk_get_from_provider().
These functions are intended to be used in the clkdev to avoid
race condition in the device tree based clock look up in clk_get().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch adds at91 smd (Soft Modem) clock implementation using common clk
framework.
Not used by any driver right now.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 usb clock implementation using common clk framework.
This clock is used to clock usb ports (ohci, ehci and udc).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds new at91 utmi clock implementation using common clk framework.
This clock is a pll with a fixed factor (x40).
It is used as a source for usb clock.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 programmable clocks implementation using common clk
framework.
A programmable clock is a clock which can be exported on a given pin to clock
external devices.
Each programmable clock is given an id (from 0 to 8).
The number of available programmable clocks depends on the SoC you're using.
Programmable clock driver only implements the clock setting (clock rate and
parent setting). It must be chained to a system clock in order to
enable/disable the generated clock.
The PCKX pins used to output the clock signals must be assigned to the
appropriate peripheral (see atmel's datasheets).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 peripheral clock implementation using common clk
framework.
Almost all peripherals provided by at91 SoCs need a clock to work properly.
This clock is enabled/disabled using PCER/PCDR resgisters.
Each peripheral is given an id (see atmel's datasheets) which is used to
define and reference peripheral clocks.
Some new SoCs (at91sam9x5 and sama5d3) provide a new register (PCR) where you
can configure the peripheral clock as a division of the master clock.
This will help reducing the peripherals power comsumption.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 system clock implementation using common clk
framework.
Some peripherals need to enable a "system" clock in order to work properly.
Each system clock is given an id based on the bit position in SCER/SCDR
registers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 master clock implementation using common clk
framework.
The master clock layout describe the MCKR register layout.
There are 2 master clock layouts:
- at91rm9200
- at91sam9x5
Master clocks are given characteristics:
- min/max clock output rate
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 pll clock implementation using common clk framework.
The pll clock layout describe the PLLX register layout.
There are four pll clock layouts:
- at91rm9200
- at91sam9g20
- at91sam9g45
- sama5d3
PLL clocks are given characteristics:
- min/max clock source rate
- ranges of valid clock output rates
- values to set in out and icpll fields for each supported output range
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 main oscillator clock implementation using common
clk framework.
If rate is not provided during clock registration it is calculated using
the slow clock (main clk parent in this case) rate and MCFR register.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds at91 PMC (Power Management Controller) base support.
All at91 clocks managed by the PMC unit will use this framework.
This framework provides the following fonctionalities:
- define a new struct at91_pmc to hide PMC internals (lock, PMC memory
mapping, irq domain, ...)
- read/write helper functions (pmc_read/write) to access PMC registers
- lock/unlock helper functions (pmc_lock/unlock) to lock/unlock access to
pmc registers
- a new irq domain and its associated irq chip to request PMC specific
interrupts (useful for clk prepare callbacks)
The PMC unit is declared as a dt clk provider (CLK_OF_DECLARE), and every
clk using this framework will declare a table of of_at91_clk_init_cb_t
and add it to the pmc_clk_ids table.
When the pmc dt clock setup function is called (by of_clk_init function),
it triggers the registration of every supported child clk (those matching
the definitions in pmc_clk_ids).
This patch copies at91_pmc_base (memory mapping) and at91sam9_idle
(function) from arch/arm/mach-at91/clock.c (which is not compiled if
COMMON_CLK_AT91 is enabled).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sWyX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-3.13' of https://github.com/mripard/linux into clk-next-sunxi-rebase
Allwinner sunXi SoCs clock changes
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
Conflicts:
drivers/clk/sunxi/clk-sunxi.c
In case of error, the function __clk_lookup() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
clk_round_rate() can be used by drivers to determine whether or not a
frequency is supported by the clock. The current Tegra clock driver
outputs an error message and a stacktrace when the requested rate isn't
supported. That's fine for clk_set_rate(), but it's confusing when all
the driver does is query whether or not a frequency is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function socfpga_clk_init() can support clocks that do not have a divider
register, but a fixed-divider that can be read from DTS. Therefore, the "reg"
property is not a failing condition for socfpga_clk_init().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[Maybe the third time will be the charm. -Alex]
If CONFIG_COMMON_CLK_DEBUG is defined, clk_debug_create_one() is
called to populate a debugfs directory with a few entries that are
common for all clock types.
If an error happens after creating the first one debugfs_remove() is
called on the clock's directory. The problem with this is that no
cleanup is done on the debugfs files already created in that
directory, so the directory never actually gets removed. This
problem is silently ignored.
Fix this by calling debugfs_remove_recursive() instead. Reset the
clk->dentry field to null afterward, to ensure it can't be mistaken
as a valid pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The clock for the PWM controller is slightly different from other
peripheral clocks on Tegra30. The clock source mux field start at
bit position 28 rather than 30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two GPUs on Tegra30 and each of them uses a separate clock, so
the secondary clock needs to be initialized in order for the gr3d module
to work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add disp1 and disp2 clocks to the clock initialization table. These
clocks are required for display and HDMI support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Hook the functions for CPU hotplug support. After the CPU is hot
unplugged, the flow controller will handle to clock gate the CPU clock.
But still need to implement an empty function to avoid warning message.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tegra124 introduces a number of new peripheral clocks. This patch adds those
to the common peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 introduces a number of a new clocks. Introduce the corresponding
the IDs for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra124 has a clock which consists of a mux and a fractional divider.
Add support for this.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has periph clocks which share the hw register. Hence locking is
required.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has an extra bank of peripheral clock registers. Add it to the
generic peripheral clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a common function which performs super clock initialization for
Tegra114 and beyond.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce new files for fixed and PMC clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduce a new file for peripheral clocks common between several Tegra
SoCs and move Tegra114 to this new infrastructure. Also PLLP and the PLLP_OUT
clocks will be initialized here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move audio clocks and PLLA initialization to a common file so it can be used by
multiple Tegra SoCs. Also a new array tegra114_clks is introduced for Tegra114
which specifies which common clocks are available on Tegra114 and what their
DT IDs are.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Add a common infra for registering clkdev. This allows decoupling clk
registration from clkdev registration.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Many clocks are common between several Tegra SoCs. Define an enum to list
them so we can move them to separate files which can be shared between
SoCs. Each SoC specific file will provide an array with the common clocks
which are present on the SoC and their DT binding ID.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Move some fields related to the PLL HW description to the tegra_clk_pll_params.
This allows some PLL code to be moved to common files later.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Use pll_ref instead of pll_re_vco as the pll_e parent on Tegra114. Also
add a 12Mhz pll_ref table entry for pll_e for Tegra114. This prevents
the system from crashing at bootup because of an unsupported pll_re_vco
rate.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
VCO min clipping, dynamic ramp setup and IDDQ init can be done in the
respective PLL clk_register functions if the parent is already registered.
This is done for other some PLLs already.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This flag indicates the peripheral clock does not have a divider. It will
simplify the initialization tables and avoids some very similar code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch makes periph_clk_enb_refcnt a global array, dynamically allocated
at boottime. It simplifies the macros somewhat and allows clocks common to
several Tegra SoCs to be defined in a separate files. Also the clks array
becomes global and dynamically allocated which allows the DT registration to
be moved to a generic funcion.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This patch determines the register bank for clock enable/disable and reset
based on the clock ID instead of hardcoding it in the tables describing the
clocks. This results in less data to be maintained in the tables, making the
code easier to understand. The full benefit of the change will be realized once
also other clocktypes will be table based.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The PLL output frequency is multiplied during the P-divider computation,
so it needs to be divided by the P-divider again before returning.
This fixes an issue where clk_round_rate() would return the multiplied
frequency instead of the real one after the P-divider.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The power-on default parent for this clock is pll_m, which turns out to
be wrong. Previously, bootloader reparented this clock. We'll do it in
the kernel as well, so that there's one less thing that we depend on
bootloader to initialize.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Perform upwards rounding when calculating dividers for periph clks on Tegra30
and Tegra114.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
pll_m will be the parent of gr2d/gr3d if we don't do this.
And because pll_m runs at a high rate so gr2d/gr3d will be
unstable. So change the parent of them to pll_c2.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
In Tegra114, vde/gr_2d/gr_3d have 3 bits for clock source selection.
So change the clock init macro for these clocks from
"TEGRA_INIT_DATA_INT" to "TEGRA_INIT_DATA_INT8".
Besides, no one uses "TEGRA_INIT_DATA_INT" after this change, so
remove this macro.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Tegra114 sbc1-sbc6 have more possible parent clocks than Tegra30.
So correct the parents and mux width for them.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
As the clock IDs are now specified in a header file, we can use those
definitions instead of maintaining an internal enum.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This commit introduces a new group of clocks present in Armada 370/XP
SoCs (called "Core Divider" clocks) and add a provider for them.
The only clock supported for now is the NAND clock (ndclk), but the
infrastructure to add the rest is already set.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since the old DMA driver got removed, these aliases are no longer
necessary.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds clkdev aliases for clocks used by PL08x DMA driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This symbol is used only in this file. The patch fix the following
sparse warning:
warning: symbol 'of_cpu_clk_setup' was not declared. Should it be static?
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
bug fixes along with updates to existing clock drivers and the
additional of new clock drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wBeW
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.13' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Mike Turquette:
"The clock changes for 3.13 are an even mix of framework improvements &
bug fixes along with updates to existing clock drivers and the
additional of new clock drivers"
* tag 'clk-for-linus-3.13' of git://git.linaro.org/people/mturquette/linux:
clk: new driver for efm32 SoC
clk: of: helper for determining number of parent clocks
clk/zynq: Fix possible memory leak
clk: keystone: Build Keystone clock drivers
clk: keystone: Add gate control clock driver
clk: keystone: add Keystone PLL clock driver
Documentation: Add documentation for APM X-Gene clock binding
clk: arm64: Add DTS clock entry for APM X-Gene Storm SoC
clk: Add APM X-Gene SoC clock driver
clk: wm831x: get rid of the implementation of remove function
clk: Correct lookup logic in clk_fetch_parent_index()
clk: Use kcalloc() to allocate arrays
clk: Add error handling to clk_fetch_parent_index()
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
Fix a possible memory leak in sun4i_osc_clk_setup().
Moved clock-frequency check to save superfluous allocation.
Signed-off-by: Victor N. Ramos Mello <victornrm@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some important clocks may get disabled as a side effect of another clock
being disabled, because they have no consumers. This patch implements a
mechanism so those clocks can be claimed by the driver and therefore
remain enabled at all times.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Random bits may get into our factors if we don't clear n, k, m and p.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code would generate one bit too long masks, and was
needlessly complicated. This patch replaces it by simpler code that can
generate the masks correctly.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds .determine_rate support to the composite clock. It will
use the .determine_rate callback from the rate component if available,
and fall back on the mux component otherwise. This allows composite
clocks to enjoy the benefits of automatic clock reparenting.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the clocks provided by the Clock Management
Unit of Energy Micro's efm32 Giant Gecko SoCs including device tree
bindings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
and adding SSP/SPI devices to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=p/3j
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.
* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: register all SSP and SPI blocks
ARM: ux500: fix I2C4 clock bit
ARM: ux500: fix clock for GPIO blocks 6 and 7
clk: ux500: fix erroneous bit assignment
ARM: ux500: fix clock for GPIO block 8
Signed-off-by: Olof Johansson <olof@lixom.net>
Due to a typo or similar, the peripheral group 2 clock 11
gate was set to bit 1 instead of bit 11. We need to fix this
to be able to set the correct enable bit in the device tree:
when trying to correct the bit assignment in the device tree,
the system would hang.
Cc: Mike Turquette <mturquette@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The order of arguments in the call to vco_set() for the ICST clocks appears to
have been switched in error, which results in the VCO not being initialised
correctly. This in turn stops the integrated LCD on things like Integrator/CP
from working correctly.
This patch fixes the order and restores the expected functionality.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@vger.kernel.org
The zynq_clk_register_fclk function can leak memory (fclk_lock) when unable
to alloc memory for fclk_gate_lock
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The SD/MMC clock is named "sdmmc_clk", and NOT "mmc_clk". Because of this,
the SD driver was getting the incorrect clock value. This prevented the
SD driver from initializing correctly.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Olof Johansson <olof@lixom.net>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Now build the keystone common clock drivers. The build is made
conditional based on COMMON_CLK_KEYSTONE
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add the driver for the clock gate control which uses PSC (Power Sleep
Controller) IP on Keystone 2 based SOCs. It is responsible for enabling and
disabling of the clocks for different IPs present in the SoC.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add the driver for the PLL IPs found on Keystone 2 devices. The PLL
IP typically has a multiplier, a divider and a post-divider. The PLL IPs like
ARMPLL, DDRPLL and PAPLL are controlled by the memory mapped register where
as the Main PLL is controlled by a PLL controller and memory map registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
nomadik_src_init references __initconst sections but lacks an __init
itself. Add __init to fix the section mismatch.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
clk: Add APM X-Gene SoC clock driver for reference, PLL, and device clocks.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Vinayak Kale <vkale@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch fixes the tclk frequency array for the Armada-370 SoC.
This bug has been introduced by commit 6b72333d
("clk: mvebu: add Armada 370 SoC-centric clock init").
A wrong tclk frequency affects the following drivers: mvsdio, mvneta,
i2c-mv64xxx and mvebu-devbus. This list may be incomplete.
About the mvneta Ethernet driver, note that the tclk frequency is used
to compute the Rx time coalescence. Then, this bug harms the coalescence
configuration and also degrades the networking performances with the
default values.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Turquette <mturquette@deferred.io>
The remove function implemented for platform driver's remove callback
just return 0 as part of its implementation.
Remove this APIs and do not pass the valid .remove for platform driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This fixes a regression for the Nomadik on the main system
timers.
The Nomadik seemed a bit slow and its heartbeat wasn't looking
healthy. And it was not strange, because it has been connected
to the 32768 Hz clock at boot, while being told by the clock driver
that it was 2.4MHz. Actually connect the TIMCLK to 2.4MHz by
default as this is what we want for nice scheduling, clocksource
and clock event.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This function is supposed to iterate over all parents of given child
clock to find the index of given parent clock in its parent list,
using parent cache if possible and falling back to string compare
otherwise. However currently the logic falls back to string compare in
every iteration in which clock cache entry does not match given parent,
due to wrong check conditions.
This patch corrects the logic to continue the loop if parent cache entry
is present and does not match requested parent clock. In addition,
redundant checks for parent cache array presence are removed, because it
is always allocated in the beginning of the function.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Instead of calculating sizes of arrays manually, kcalloc() can be used
to allocate arrays of elements with defined size. This is just a cleanup
patch without any functional changes.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There are at least two different error cases that can happen in
clk_fetch_parent_index() function:
- allocation failure,
- parent clock lookup failure,
however it returns only an u8, which is supposed to contain parent clock
index.
This patch modified the function to return full int instead allowing
positive clock indices and negative error codes to be returned. All
users of this function are adjusted as well to handle the return value
correctly.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=FQfo
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
This is a huge device tree and ATAG removal series for ux500:
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
* tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (92 commits)
ARM: ux500: delete devices-common remnants
clk: ux500: Provide a look-up for the ARMSS clock
ARM: ux500: Enable CPUFreq on Snowball
ARM: ux500: Provide a Device Tree node for CPUFreq in the DBx500
ARM: ux500: Provide a clock lookup for the Hash driver
ARM: ux500: Provide a clock lookup for the Crypto driver
ARM: ux500: Fix trivial white-space error in the DBX500 DTSI file
ARM: ux500: Remove ATAG booting support for Snowball
ARM: ux500: Remove ATAG booting support for HREF
ARM: ux500: Remove ATAG booting support for U8520
ARM: ux500: Remove ATAG booting support for MOP500
ARM: ux500: Purge UIB framework when booting with ATAGs
ARM: ux500: Take out STUIB support when not booting with Device Tree
ARM: ux500: Remove BU21013 ROHM TS support when booting with only ATAGs
ARM: ux500: Don't register the STMPE/SKE when booting with ATAG support
ARM: ux500: Delete U8500 UIB support when booting with ATAGs
ARM: ux500: Don't register Synaptics RMI4 TS when booting with ATAGs
ARM: ux500: Purge DB8500 PRCMU registration when not booting with DT
ARM: ux500: Stop requesting the SoC device to play 'parent' role
ARM: ux500: Remove UART support when booting without Device Tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch converts clk-imx2[38] clocksource_of_init compatible init
associated with fsl,imx2[38]-clkctrl. With arch/arm calling
of_clk_init(NULL) from time_init(), we can now also remove custom
.init_time hooks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks. Highbank clock provider need a reference
to system registers, as a workaround current clk driver maps those
independent of arch code now.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks. Also remove call to of_clk_init from
clk-bcm2835 with core fixed_clock match, as this has already been
registered now.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Current vt8500 board init calls of_clk_init() from vtwm_clk_init. To allow
consolidation of DT driven .time_init, move of_clock_init() to a temporary
.time_init callback that will be removed when arch-wide callback is available.
With previous pmc_base parsing helper for vt8500 clock providers, we can also
safely remove the call to vtwm_clk_init() and get rid of some includes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Mike Turquette <mturquette@linaro.org>
Currently, clock providers for vt8500 depend on machine_init providing
pmc_base address before calling of_clk_init. With upcoming arch-wide
.time_init calling of_clk_init, we should make clock providers independent
of mach code. This adds a pmc_base parsing helper to current clock provider
that gets called if there is no pmc_base set, yet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Mike Turquette <mturquette@linaro.org>
Common clock framework allows to register clock providers to get called
on of_clk_init() by using CLK_OF_DECLARE. This converts sunxi clock
providers to make use of it and get rid of the mach specific clk init
call. As sunxi has a bunch of independent clk provider nodes, we hook
current clock init to board compatible to make it called once.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Common clock framework allows to register clock providers to get called
on of_clk_init() by using CLK_OF_DECLARE. This converts prima2 clock
provider to make use of it and get rid of the mach specific clk init
call.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Common clock framework allows to register clock providers to get called
on of_clk_init() by using CLK_OF_DECLARE. This converts nomadik clock
provider to make use of it and get rid of the mach specific clk init
call. As clocks require system reset controller base address to be
initialized each clock driver checks src_base and calls new
nomadik_src_init if required.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
nomadik_clk_init currently also maps system reset controller base address
used by clocks and registers a reboot notifier. To allow further cleanup of
nomadik clk setup, this moves system reset controller setup from
nomadik_clk_init to its own function.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
The ARMSS clock is used by the newly DT enabled CPUFreq driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables the TWD fixed factor clock to be specified from
Device Tree via phandles to the "smp-twd-clock" node.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables the RTC fixed frequency clock to be specified from
Device Tree via phandles to the "rtc32k-clock" node.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables clocks to be specified from Device Tree via phandles
to the "prcc-kernel-clock" node.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables clocks to be specified from Device Tree via phandles
to the "prcc-periph-clock" node.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables clocks to be specified from Device Tree via phandles
to the "prcmu-clock" node.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PRCC (peripheral and kernel) clocks are specified using a property tuple
<&phandle base bit>, where 'base' is the peripheral (1, 2, 3, 5 or 6),
and bit is read-in value into that peripheral stipulated by the hardware
specification.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The functional components will be added on a per-clock basis.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here we're using the old clock initialisation function as a template.
It's necessary to remove all of the clk_register_clkdev() calls as
they don't make sense when booting with Device Tree.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no mention of the PRCMU_BML8580CLK in any of the Design
Specifications for the chips supported in Mainline. In fact, where it
is incorrectly used in the u8540 clock definition driver it would
have the side effect of using the incorrect clock management address
([PRCM_BML8580CLK_MGT] 0x108 instead of the correct value 0x04C).
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a regression for the Nomadik on the main system
timers.
The Nomadik seemed a bit slow and its heartbeat wasn't looking
healthy. And it was not strange, because it has been connected
to the 32768 Hz clock at boot, while being told by the clock driver
that it was 2.4MHz. Actually connect the TIMCLK to 2.4MHz by
default as this is what we want for nice scheduling, clocksource
and clock event.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch migrates the s3c64xx platform to use the new clock driver
using Common Clock Framework.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
In __clk_init(), after a clock is mostly initialized, a scan is done
of the orphan clocks to see if the clock being registered is the
parent of any of them.
This code assumes that any clock that provides a get_parent method
actually has at least one parent, and that's not a valid assumption.
As a result, an orphan clock with no parent can return *something*
as the parent index, and that value is blindly used to dereference
the orphan's parent_names[] array (which will be ZERO_SIZE_PTR or
NULL).
Fix this by ensuring get_parent is only called for orphans with at
least one parent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since the _get_rate() helper has been modified to use __clk_lookup()
internally, checking of PLL input rates can be done using it and so the
registration code can be simplified.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds rate tables for PLLs that can be reconfigured at runtime
for Exynos4x12 SoCs. Provided tables contain PLL coefficients for
input clock of 24 MHz and so are registered only in this case. MPLL does
not need runtime reconfiguration and so table for it is not provided.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds rate tables for PLLs that can be reconfigured at runtime
for Exynos4210 SoCs. Provided tables contain PLL coefficients for
input clock of 24 MHz and so are registered only in this case. MPLL does
not need runtime reconfiguration and so table for it is not provided.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since PLL input frequency must be known before PLL registration,
mout_vpllsrc clock which is a reference clock of VPLL must be registered
before VPLL.
This patch reorders clock registration to register mout_vpllsrc before
VPLL.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch implements round_rate and set_rate callbacks of PLL46xx
driver to allow reconfiguration of PLL at runtime.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch modifies PLL46xx support code and its users to use the
recently introduced common PLL registration helper.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch implements round_rate and set_rate callbacks of PLL45xx
driver to allow reconfiguration of PLL at runtime.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch modifies PLL45xx support code and its users to use the
recently introduced common PLL registration helper.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This array defines PLLs specific to Exynos 4x12 SoCs and not for all
Exynos 4 SoCs, so the name should represent that.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Exynos 4 supports only DT based bootup, so non-DT cases does not need to
be handled anymore.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since Exynos does not support legacy non-DT boot anymore, most of clock
lookups happen using device tree, so most of static clkdev aliases are no
longer necessary. This patch removes them.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no need to use clkdev inside the clock driver to retrieve the
clocks for internal use. Instead __clk_lookup() helper can be used to
look up clocks by their platform name.
This patch modifies the behavior of _get_rate() helper to look up clocks
by platform name and adjusts all users of it to pass platform names
instead of clkdev aliases.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Exynos cpufreq driver is the only remaining piece of code that needs
static clkdev aliases for operation, because it can not do device tree
based clock lookups yet.
This patch moves clock alias definitions for those clocks to separate
arrays that can be used with samsung_clk_register_alias() helper.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
The __clk_get_flags() symbol is exported immediately following the
clk_unprepare_unused_subtree() function. This is unusual, since a symbol
export typically follows body of the function that it exports.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit 71472c0 (clk: add support for clock reparent on set_rate) added a
dereference of the new_parent pointer in clk_reparent(), but as detected
by smatch clk_reparent() later checks whether new_parent is NULL.
The dereference was in order to clear the new parent's new_child pointer
to avoid duplicate POST_RATE_CHANGE notifications, so clearly isn't
necessary if the new parent is NULL, so move it inside the "if
(new_parent)" block.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Otherwise any attempt to interact with the hardware will crash. This is
what happens when drivers get written blind.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
dout_pixel is a new ID allocated for pixel clock divider. It is
queried in the driver to pass as the parent to hdmi clock while
switching between parents.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
hdmi driver needs to change the parent of hdmi clock
to pixel clock or hdmiphy clock, based on the stability
of hdmiphy. This patch is exposing the mux for changing
the parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Listing sclk_hdmiphy at 0th position in the list of parents is
causing wrong configuration in reg SRC_DISP10.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adding sysmmu clock for mixer for exynos5420.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add sclk_hdmiphy to the list of exposed clocks. This is required
by hdmi driver to change the parent of hdmi clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since the driver was written an is_prepared() operation has been made
possible. Since the driver uses I2C I/O only prepare operations are
provided so move the is_enabled() operation over to is_prepared().
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
parent of hdmi and mixer block is mentioned as aclk200 which is
not correct. It is clocked by the ouput of aclk200_disp1. Hence
parent for mixer and hdmi clocks is changed to aclk200_disp1.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The lock bit on PLL_U does not seem to be working correctly and
sometimes never gets set when waiting for the PLL to come up.
Remove the TEGRA_PLL_USE_LOCK flag to use a constant delay.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: refreshed patch based on sunxi changes]
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
While at it also make 'u300_clk_lookup' static as it is used only
in this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
These patches mostly do some cleanup to introduce the basic gated clocks for
the Allwinner A10s, A20 and A31 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=q+yI
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-3.12' of https://github.com/mripard/linux into clk-next-sunxi
Allwinner clock changes for 3.12
These patches mostly do some cleanup to introduce the basic gated clocks for
the Allwinner A10s, A20 and A31 SoCs.
Conflicts:
drivers/clk/sunxi/clk-sunxi.c
the common clock drivers were motivated/initiated by ARM development
and apparently assume little endian peripherals
wrap register/peripherals access in the common code (div, gate, mux)
in preparation of adding COMMON_CLK support for other platforms
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently of_clk_init() finds a matching device node while holding
the device tree spinlock. When a matching device node is found, the
lock is dropped and then re-acquired in order to get a reference
to the matching device id structure.
Acquiring the spinlock twice is unnecessary (and it opens a
vulnerable window that could conceivably lead to errors).
There already exists an interface for both finding and taking a
reference to a device id under lock, so use it.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
With the recent move towards CLK_OF_DECLARE(...), the driver stopped
initializing osc32k, which is compatible "fixed-clock". This is because
we never called of_clk_init(NULL). Fix this by moving the only other
simple clock (osc24M) to use CLK_OF_DECLARE(...) and call of_clk_init(NULL)
to initialize both of them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch modifies PLL6552 and PLL6553 clock drivers to use recently
added common Samsung PLL registration method.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Allwinner A20 is almost identical to the earlier A10 SoC from
Allwinner on many aspects, including the clocks tree. However, since the
A20 has some additionnal IPs compared to the A10, the clock tree isn't
exactly the same, especially when it comes to the gated clocks
available. We thus need to register different clock gates for the A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The A31 has a mostly different clock set compared to the other older
SoCs currently supported in the Allwinner clock driver.
Add support for the basic useful clocks. The other ones will come in
eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The divider width used to be hardcoded. Some A31 dividers are no longer
with the hardcoded width, so we need to make it specific to each divider
and set it in the dividers data.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Rename all the generic-named structure to sun4i to avoid confusion when
we will introduce the sun6i (A31) clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
With the recent move towards CLK_OF_DECLARE(...), the driver stopped
initializing osc32k, which is compatible "fixed-clock". This is because
we never called of_clk_init(NULL). Fix this by moving the only other
simple clock (osc24M) to use CLK_OF_DECLARE(...) and call of_clk_init(NULL)
to initialize both of them.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
The Allwinner A10s has a slightly different gates set than the A10 and
A13, so add these gates to the clk driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
At some point changes to clk_set_rate and clk_set_parent introduced a
bug whereby NULL struct clk pointers were treated as an error. This is
in violation of the API in include/linux/clk.h. Reintroduce graceful
handling of NULL clk's by bailing from clk_set_rate and clk_set_parent
with return codes of zero.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Just small two changes where the first fixes
documentation and the second improves
code readability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlITEOUACgkQykllyylKDCF/NACeL44IBsj0MLhdhJmPCZKbt6Iq
wIMAn1jLwzIUnKug6TuT3GzsNnrrNaCi
=1u+P
-----END PGP SIGNATURE-----
Merge tag 'zynq-clk-for-3.12' of git://git.xilinx.com/linux-xlnx into clk-next
arm: Xilinx Zynq clock changes for v3.12
Just small two changes where the first fixes
documentation and the second improves
code readability.
Use more descriptive #defines for the minimum and maximum PLL
feedback divider.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement clk-mux remuxing if the CLK_SET_RATE_NO_REPARENT flag isn't
set. This implements determine_rate for clk-mux to propagate to each
parent and to choose the best one (like clk-divider this chooses the
parent which provides the fastest rate <= the requested rate).
The determine_rate op is implemented as a core helper function so that
it can be easily used by more complex clocks which incorporate muxes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a CLK_SET_RATE_NO_REPARENT clock flag, which will prevent muxes
being reparented during clk_set_rate.
To avoid breaking existing platforms, all callers of clk_register_mux()
are adjusted to pass the new flag. Platform maintainers are encouraged
to remove the flag if they wish to allow mux reparenting on set_rate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Chao Xie <xiechao.mail@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spear-devel@list.st.com
Cc: linux-tegra@vger.kernel.org
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com> [tegra]
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [sunxi]
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com> [Zynq]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add core support to allow clock implementations to select the best
parent clock when rounding a rate, e.g. the one which can provide the
closest clock rate to that requested. This is by way of adding a new
clock op, determine_rate(), which is like round_rate() but has an extra
parameter to allow the clock implementation to optionally select a
different parent clock. The core then takes care of reparenting the
clock when setting the rate.
The parent change takes place with the help of some new private data
members. struct clk::new_parent specifies a clock's new parent (NULL
indicates no change), and struct clk::new_child specifies a clock's new
child (whose new_parent member points back to it). The purpose of these
are to allow correct walking of the future tree for notifications prior
to actually reparenting any clocks, specifically to skip child clocks
who are being reparented to another clock (they will be notified via the
new parent), and to include any new child clock. These pointers are set
by clk_calc_subtree(), and the new_child pointer gets cleared when a
child is actually reparented to avoid duplicate POST_RATE_CHANGE
notifications.
Each place where round_rate() is called, determine_rate() is checked
first and called in preference. This restructures a few of the call
sites to simplify the logic into if/else blocks.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Move some parent related functions up in clk.c so they can be used by
the modifications in the following patch which enables clock reparenting
during set_rate. No other changes are made so this patch makes no
functional difference in isolation. This is separate from the following
patch primarily to ease readability of that patch.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Abstract access to the clock parent cache by defining
clk_get_parent_by_index(clk, index). This allows access to parent
clocks from clock drivers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_register_divider() needs to be exported so that it could be used
in a module driver, otherwise we get the following error:
ERROR: "clk_register_divider" [sound/soc/mxs/snd-soc-mxs.ko] undefined!
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: also export clk_register_divider_table]
Export this symbol so that modules can register fixed rate
clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The ISP clock registers belong to the ISP power domain and may change
their values if this power domain is switched off/on. Add
CLK_GET_RATE_NOCACHE flags to ensure we do not rely on invalid cached
data when setting or getting frequency of those clocks.
Without this fix the FIMC-IS Cortex-A5 core and AXI bus clocks have
incorrect frequencies, which breaks the ISP operation and starting the
video pipeline fails with timeouts reported by the FIMC-IS firmware.
See related commit 722a860ecb "[media]
exynos4-is: Fix FIMC-IS clocks initialization" for more details.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Zynq's Ethernet clocks are created by the following hierarchy:
mux0 ---> div0 ---> div1 ---> mux1 ---> gate
Rate change requests on the gate have to propagate all the way up to
div0 to properly leverage all dividers. Mux1 was missing the
CLK_SET_RATE_PARENT flag, which is required to achieve this.
This does not fix a specific regression but the clock driver was merged
for 3.11-rc1, so best to fix the known bugs before the release.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: added to changelog]
The clk_mux for the system watchdog timer reused the register lock
dedicated to the Ethernet module - for no apparent reason.
Add a lock dedicated to the SWDT's clock register to remove this
wrong dependency.
This does not fix a specific regression but the clock driver was merged
for 3.11-rc1, so best to fix the known bugs before the release.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: added to changelog]
When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support to register three(AP/CP/BT) buffered 32.768 KHz
outputs of mfd-s2mps11 with common clock framework.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'exynos5420_plls' is used only in this file. Make is static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
exynos5250_plls is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'exynos4_plls' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix the following sparse warning:
drivers/clk/mxs/clk-imx23.c:102:12: warning: symbol 'mx23_clocks_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_register_composite() and clk_register_factors() return ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds new, Common Clock Framework-based clock driver for Samsung
S3C64xx SoCs. The driver is just added, without actually letting the
platforms use it yet, since this requires more intermediate steps.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for PLL6552 and PLL6553 PLLs present on Samsung
S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some platforms have read-only clock muxes that are preconfigured at
reset and cannot be changed at runtime. This patch extends mux clock
driver to allow handling such read-only muxes by adding new
CLK_MUX_READ_ONLY mux flag.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
While trying to get rate of "mout_vpllsrc" MUX (parent) for registering the
"fout_vpll" (child), we found get rate was failing.
So this patch moves the mout_vpllsrc MUX out of the existing common list
and registers the mout_vpllsrc MUX before the PLL registrations.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds set_rate and round_rate clk_ops for PLL36xx
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch add set_rate() and round_rate() for PLL35xx
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch defines a common rate_table which will contain recommended p, m, s,
k values for supported rates that needs to be changed for changing
corresponding PLL's rate.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch removes samsung_clk_register_pll35xx() and
samsung_clk_register_pll36xx() registaration functions as users migrated to
new samsung_clk_register_pll().
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch migrates exynos5420 pll registeration to use common
samsung_clk_register_pll() by intialising table of PLLs and adding PLLs to
unique id list of clocks.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch migrates exynos4 pll registeration to use common
samsung_clk_register_pll() by intialising table of PLLs.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch migrates exynos5250 pll registeration to use common
samsung_clk_register_pll() by intialising table of PLLs and adding PLLs to
unique id list of clocks.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch defines a common samsung_clk_register_pll()
Since pll2550 & pll35xx and pll2650 & pll36xx have exactly same clk ops
implementation, added pll2550 and pll2650 also.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch unifies clk strutures used for PLL35xx & PLL36xx and
adding an extra member lock_reg, so that common code can be factored out.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Added clock entries for thermal management unit (TMU) for
Exynos4 SoCs.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
hdmi driver needs hdmiphy clock which is one of the parent
for hdmi mux clock. This is required while changing the parent
of mux clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
hdmi driver needs to change the parent of hdmi clock
frequently between pixel clock and hdmiphy clock. hdmiphy is
not stable after power on and for a short interval while changing
the phy configuration. For this duration pixel clock is used to
clock hdmi.
This patch is exposing the mux for changing parent.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adds gate clock for G2D IP for Exynos5250 SoC.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
exynos_audss_clk_init() is used only in this file. Make it
static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Subsequent to the cleanup in commit 3c70348c7c ("ARM: EXYNOS:
Remove legacy timer initialization code"), this function has no more
users. Hence remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Symbols referenced only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adding suspend/resume function for tegra_cpu_car_ops. We only save and
restore the setting of the clock of CoreSight. Other clocks still need
to be taken care by clock driver.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
across several different platforms and architectures, fixes to existing
drivers, a MAINTAINERS file fix and improvements to the basic clock
types that allow them to be of use to more platforms than before. Only a
few fixes to the core framework are included with most all of the
changes landing in the various clock drivers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwMB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux
Pull clock framework updates from Mike Turquette:
"The common clock framework changes for 3.11 include new clock drivers
across several different platforms and architectures, fixes to
existing drivers, a MAINTAINERS file fix and improvements to the basic
clock types that allow them to be of use to more platforms than before.
Only a few fixes to the core framework are included with most all of
the changes landing in the various clock drivers themselves."
* tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux: (55 commits)
clk: tegra: fix ifdef for tegra_periph_reset_assert inline
clk: tegra: provide tegra_periph_reset_assert alternative
clk: exynos4: Fix clock aliases for cpufreq related clocks
clk: samsung: Add MUX_FA macro to pass flag and alias
clk: add support for Rockchip gate clocks
clk: vexpress: Make the clock drivers directly available for arm64
clk: vexpress: Use full node name to identify individual clocks
clk: tegra: T114: add DFLL DVCO reset control
clk: tegra: T114: add DFLL source clocks
clk: tegra: T114: add FCPU clock shaper programming, needed by the DFLL
clk: gate: add CLK_GATE_HIWORD_MASK
clk: divider: add CLK_DIVIDER_HIWORD_MASK flag
clk: mux: add CLK_MUX_HIWORD_MASK
clk: Always notify whole subtree when reparenting
MAINTAINERS: make drivers/clk entry match subdirs
clk: honor CLK_GET_RATE_NOCACHE in clk_set_rate
clk: use clk_get_rate() for debugfs
clk: tegra: Use override bits when needed
clk: tegra: override bits for Tegra30 PLLM
clk: tegra: override bits for Tegra114 PLLM
...
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
cpufreq driver for EXYNOS4 based SoCs are not platform drivers, hence
we cannot currently pass the clock names through a device tree node.
Instead, we need to make them available through a global alias.
Clock alias modifications for EXYNOS4 specific clocks are as below.
Alias for clock 'arm_clk' is 'armclk'.
Alias for clock 'mout_apll' is 'mout_apll'.
Alias for clock 'mout_core' is 'moutcore'.
For EXYNOS4210, alias for clock 'sclk_mpll' is 'mout_mpll'.
For EXYNOS4412, alias for clock 'mout_mpll_user_c' is 'mout_mpll'.
Some of the clock aliases are newly defined and some are fixed up.
While at it, also modify the debug messages to print the clock
values appropriately.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cpufreq driver for some Samsung platforms have not yet been designed as
a platform driver, thereby they can only access clocks with an alias
name.
For EXYNOS4210, one such clock also requires a flag to be set, hence
there is a need to create another macro that can handle both flag and
alias.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds basic support for gate-clocks on Rockchip SoCs.
There are 16 gates in each register and use the HIWORD_MASK
mechanism for changing gate settings.
The gate registers form a continuos block which makes the dt node
structure a matter of taste, as either all 160 gates can be put into
one gate clock spanning all registers or they can be divided into
the 10 individual gates containing 16 clocks each.
The code supports both approaches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- Lee Jones' pinctrl compat ontology patches
- A real clock driver for the Nomadik, 100% DT-based
- Device tree changes for the Nomadik clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=0yyI
-----END PGP SIGNATURE-----
Merge tag 'nomadik-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik DT and clock work:
- Lee Jones' pinctrl compat ontology patches
- A real clock driver for the Nomadik, 100% DT-based
- Device tree changes for the Nomadik clocks
* tag 'nomadik-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
pinctrl/nomadik: Standardise Pinctrl compat string for Nomadik based platforms
ARM: nomadik: Standardise Nomadik STN8815 based Pinctrl compat string in the DTS
Conflicts:
arch/arm/boot/dts/ste-nomadik-s8815.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Nomadik clock implementation was a stub just using
fixed clocks.
This implements the clocks properly instead of relying
on them all being on at boot and leaving them all on.
The PLLs are on the top locking to the main chrystal
oscillator, then the HCLK for the peripherals are
below PLL2.
The gated clocks are implemented with zero cells and
given the clock ID as a property of each node, so every
gate need to have its own node in the device tree.
This is because the gate registers contain both HCLK
gates and PCLK gates, where the latter has HCLK as
parent. As can be seen from the register layout, this
is a complete mixup, which means all these gates need
their own node to properly model parent/child relations
for PCLKs apart from the HCLKs.
This driver also adds a helpful debugfs file to inspect
the hardware state of the clock gates.
This is the end result in <debugfs>/clk/clk_summary
after applying a proper device tree:
ulpiclk 0 0 60000000
mxtal 3 3 19200000
pll2 1 1 864000000
clk48 3 3 48000000
rngcclk 1 1 48000000
usbmclk 0 0 48000000
mshcclk 0 0 48000000
mspclk3 0 0 48000000
x3dclk 0 0 48000000
skeclk 0 0 48000000
owmclk 0 0 48000000
mspclk2 0 0 48000000
mspclk1 0 0 48000000
uart2clk 0 0 48000000
ipbmcclk 0 0 48000000
ipi2cclk 0 0 48000000
usbclk 0 0 48000000
mspclk0 0 0 48000000
uart1clk 1 2 48000000
i2c1clk 0 0 48000000
i2c0clk 0 0 48000000
sdiclk 1 1 48000000
uart0clk 0 0 48000000
sspiclk 0 0 48000000
irdaclk 0 0 48000000
clk72 0 0 72000000
difclk 0 0 72000000
clcdclk 0 0 72000000
clk216 0 0 216000000
hsiclkrx 0 0 216000000
clk108 0 0 108000000
hsiclktx 0 0 108000000
clk27 0 0 27000000
pll1 1 1 264000000
hclk 3 3 264000000
hclkrng 1 1 264000000
hclkusbm 0 0 264000000
hclkcryp 0 0 264000000
hclkhash 0 0 264000000
hclk3d 0 0 264000000
hclkhpi 0 0 264000000
hclksva 0 0 264000000
hclksaa 0 0 264000000
hclkdif 0 0 264000000
hclkusb 0 0 264000000
hclkclcd 0 0 264000000
hclkdma1 0 0 264000000
hclksdram 0 0 264000000
hclksmc 1 1 264000000
hclkdma0 0 0 264000000
pclk 7 9 264000000
pclkmsp3 0 0 264000000
pclkmshc 0 0 264000000
pclkhsem 0 0 264000000
pclkske 0 0 264000000
pclkowm 0 0 264000000
pclkmsp2 0 0 264000000
pclkmsp1 0 0 264000000
pclkuart2 0 0 264000000
pclkxti 0 0 264000000
pclkhsi 0 0 264000000
pclkmsp0 0 0 264000000
pclkuart1 1 1 264000000
pclki2c1 0 0 264000000
pclki2c0 0 0 264000000
pclksdi 1 1 264000000
pclkuart0 1 1 264000000
pclkssp 0 0 264000000
pclkirda 0 0 264000000
timclk 1 1 2400000
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new arm64 architecture has no idea of platform or machine, so
it doesn't have to define ARCH_VEXPRESS configuration option at
all. To allow user to select the drivers at all, make it depend
on ARM64 as well.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Previously all the clocks were reported as "osc". Now it will be
something like "/dcc/osc@0".
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlG+ysgACgkQykllyylKDCENewCgk3LUwpMxepV1JOaNBmUJ0A09
jtMAnA395sve+FBxYjfM+nSAmbnl5RYl
=KBrZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx into next/dt
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Intel BayTrail has almost the same Low Power Subsystem than Lynxpoint with
few differences. Peripherals are clocked with different speeds (typically
lower) and the clock is not always gated. To support this we add
possibility to share a common fixed rate clock and make clock gating
optional.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EXYNOS5420 clocks are statically listed and registered using
the Samsung specific common clock helper functions.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DFLL DVCO reset line control functions to the CAR IP block driver.
The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block. This reset line is asserted upon SoC
reset. Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.
Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add the input clocks needed by the DFLL IP blocks. Initialize them to
51MHz (as required by the DFLL GFD) and to use the PLL_P clock source.
This patch is a collaboration with Peter De Schrijver
<pdeschrijver@nvidia.com>.
Thanks to Laxman Dewangan <ldewangan@nvidia.com> for identifying the
requirement to keep the DFLL clocks enabled to resolve PWR_I2C timeout
issues.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds enum entries for div_i2s1 and div_i2s2 which are
required for i2s1 and i2s2 controllers.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Audio subsystem is introduced in s5pv210 and exynos platforms.
This has seperate clock controller which can control i2s0 and
pcm0 clocks. This patch registers the audio subsystem clocks
with the common clock framework on Exynos family.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock functions to initialize, enable, and disable the FCPU clock
shapers, based on the FCPU voltage rail state. These will be used by
the DFLL clocksource driver code.
This version of the patch contains a fix for a problem noticed by Andrew
Chew <achew@nvidia.com>, where some of the FINETRIM_R bitfields were
incorrectly defined.
Based on code originally written by Aleksandr Frid <afrid@nvidia.com>.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Andrew Chew <achew@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Cc: Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the last of the U300 clocks to being probed from
the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the slow, fast, AHB bridge and "rest" clocks on
the U300 system controller over to registration from the
device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the fixed and fixed-factor clocks in the U300
platform to register themselves from the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Registering pciex as peripheral clock instead of fixed clock
as tegra_perih_reset_assert(deassert) api of this clock api
gives warning and ultimately does not succeed to assert(deassert)
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In Rockchip Cortex-A9 based chips, they don't use paradigm of
reading-changing-writing the register contents. Instead they
use a hiword mask to indicate the changed bits.
When b1 should be set as gate, it also needs to indicate the change
by setting hiword mask (b1 << 16).
The patch adds gate flag for this usage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In both Hisilicon & Rockchip Cortex-A9 based chips, they don't use the
paradigm of reading-changing-writing the register contents.
Instead they use a hiword mask to indicate the changed bits.
When b01 should be set as setting divider, it also needs to indicate
the change by setting hiword mask (b11 << 16).
The patch adds divider flag for this usage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In both Hisilicon & Rockchip Cortex-A9 based chips, they don't use the
paradigm of reading-changing-writing the register contents.
Instead they use a hiword mask to indicate the changed bits.
When b01 should be set as switching mux, it also needs to indicate
the change by setting hiword mask (b11 << 16).
The patch adds mux flag for this usage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
A clock's notifier count only reflects notifiers which are registered
directly for that clock. A reparent operation though affects the whole
subtree because of a potential rate change.
When issuing the pre rate change notifications only the notifier count
for the clock to be changed is considered and notifiers for subclocks
may never be called. Resulting in clocks in the subtree which have
registered notifiers, may receive a POST_- or ABORT_RATE_CHANGE
notification, without a PRE_RATE_CHANGE_NOTIFICATION.
Therefore always traverse the whole subtree when issueing pre rate
change notifications during a reparent operation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This branch contains fixes and enhancement for core Tegra Soc support:
* CPU hotplug support for Tegra114.
* Some preliminary work on Tegra114 CPU sleep modes.
* Minor fix for EMC table DT parsing.
This branch is based on v3.10-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=osxB
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: core SoC support enhancements
This branch contains fixes and enhancement for core Tegra Soc support:
* CPU hotplug support for Tegra114.
* Some preliminary work on Tegra114 CPU sleep modes.
* Minor fix for EMC table DT parsing.
* tag 'tegra-for-3.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: don't pass CPU ID to tegra_{set,clear}_cpu_in_lp2
ARM: tegra: cpuidle: using IS_ENABLED for multi SoCs management in init func
ARM: tegra: hook tegra_tear_down_cpu function in the PM suspend init function
ARM: tegra: cpuidle: move the init function behind the suspend init function
ARM: tegra: remove ifdef in the tegra_resume
ARM: tegra: add cpu_disable for hotplug
ARM: tegra114: add CPU hotplug support
clk: tegra114: implement wait_for_reset and disable_clock for tegra_cpu_car_ops
ARM: tegra114: add power up sequence for warm boot CPU
ARM: tegra: make tegra_resume can work for Tegra114
ARM: tegra: skip SCU and PL310 code when CPU is not Cortex-A9
ARM: tegra: add an assembly marco to check Tegra SoC ID
ARM: tegra: emc: correction of ram-code parsing from dt
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently 'pmu' clock is not handled by any of the drivers.
Also before the introduction of CCF, this clock was not defined,
hence was left enabled always.
When this clock is disabled, software reset register becomes
inaccessible and system reboot doesn't work.
Upon restoring the default behaviour, system reboot starts working.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_set_rate() uses clk->rate directly. This causes problems if the clock
is marked as CLK_GET_RATE_NOCACHE. Hence call clk_get_rate() to get the
current rate.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
debugfs uses the rate field directly. However this ignores the
CLK_GET_RATE_NOCACHE flag. Call clk_get_rate() instead.
Tested-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
PLLM has override bits in the PMC. Use those when PLLM_OVERRIDE_ENABLE
is set.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Define override bits for Tegra30 PLLM.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Define override bits for Tegra114 PLLM.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed up trivial merge conflict]
PLLM can have override bits in the PMC. Describe those in the PLL parameters.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use the correct parents for sclk according to the TRM.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The PLLRE flags weren't set correctly. Fixed in this patch.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The m,n,p fields don't have the same bit offset and width across all PLLs.
This patch allows SoC specific files to indicate the offset and width.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The pllp_out2 should be integer only, the fractional bit should always be 0.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support to gate the clocks that directly feed peripherals. For clocks
with multiple parents, add the ability to determine the correct parent,
and also set parents. Also add support to calculate and set the clocks'
rate.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Mike Turquette <mturquette@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Olof Johansson <olof@lixom.net>
Cc: Pavel Machek <pavel@denx.de>
CC: <linux@arm.linux.org.uk>
v4:
- Add Acked-by: Mike Turquette
v3:
- Addressed comments from Pavel
v2:
- Fix space/indent errors
- Add streq for strcmp == 0
Signed-off-by: Olof Johansson <olof@lixom.net>
The pllc and pllxc code weren't always using the correct pdiv_map to
map between the post divider value and the hw p field. This could result
in illegal values being programmed in the hw.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is required to be able to disable spear320 support
after the spear320_clk_init() prototype changed for the real
function but not for the dummy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add G2D clocks for Exynos4x12 SoC and sclk_fimg2d required by G2D
IP.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The KDIV value is often listed as unsigned but it needs to be treated
as a 16-bit signed value when using it in calculations. Fix our rate
recalculation to do this correctly.
Before doing this, I tried setting EPLL on exynos5250 to:
rate, m, p, s, k = 80000000, 107, 2, 4, 43691
This rate is exactly from the table in the exynos5250 user manual.
I read this back as 80750003 with:
cat /sys/kernel/debug/clk/fin_pll/fout_epll/clk_rate
After this patch, it reads back as 80000003
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If the current rate of parent clock is sufficient to provide child a
requested rate with a proper divider setting, the rate change request
should not be propagated. Instead, changing the divider setting is good
enough to get child clock run at the requested rate.
On an imx6q clock configuration illustrated below,
ahb --> ipg --> ipg_per
132M 66M 66M
calling clk_set_rate(ipg_per, 22M) with the current
clk_divider_bestdiv() implementation will result in the rate change up
to ahb level like the following, because of the unnecessary/incorrect
rate change propagation.
ahb --> ipg --> ipg_per
66M 22M 22M
Fix the problem by trying to see if the requested rate can be achieved
by simply changing the divider value, and in that case return the
divider immediately from function clk_divider_bestdiv() as the best
one, so that all those unnecessary rate change propagation can be saved.
Reported-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'mout_mpll' is added the list of parent clocks for 'mout_cpu'.
'mout_mpll' is an alias to the clock 'sclk_mpll'. Hence 'sclk_mpll'
should be added to the list of parent clocks.
This results in an error when cpufreq driver for EXYNOS5250 tries to
set 'mout_mpll' as a parent for 'mout_cpu'.
clk_set_parent: clk sclk_mpll can not be parent of clk mout_cpu
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cpufreq driver for EXYNOS5250 is not a platform driver, hence we cannot
currently pass the clock names through a device tree node. Instead, we
need to make them available through a global alias.
cpufreq driver for EXYNOS5250 requires four clocks - 'armclk',
'mout_cpu', 'mout_mpll' and 'mout_apll'.
'armclk' has already been defined with an alias, 'mout_cpu', 'mout_mpll'
and 'mout_apll' are now defined with an alias.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Tero Kristo