This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.
Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPC block is responsible for parsing and forwarding
packets to different NIXLFs. NPC has 16 KPU engines
(Kangaroo parse engine) and one iKPU which represents
pkinds. Each physical port either CGX/LBK is assigned
a pkind and upon receiving a packet HW takes that port's
pkind and starts parsing as per the KPU engines config.
This patch adds header files which contain configuration
profile/array for each of the iKPU and 16 KPU engines.
Signed-off-by: Hao Zheng <hao.zheng@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mailbox message to reset
a NIXLF's receive and transmit HW stats.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a PF/VF driver to configure
NIX transmit scheduler queues via mbox. Since PF/VF doesn't
know the absolute HW index of the NIXLF attached to it, AF
traps the register config and overwrites with the correct
NIXLF index.
HW supports shaping, colouring and policing of packets with
these multilevel traffic scheduler queues. Instead of
introducing different mbox message formats for different
configurations and making both AF & PF/VF driver implementation
cumbersome, access to the scheduler queue's CSRs is provided
via mbox. AF checks whether the sender PF/VF has the
corresponding queue allocated or not and dumps the config
to HW. With a single mbox msg 20 registers can be configured.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a PF/VF to allocate or free NIX transmit
scheduler queues via mbox. For setting up pkt transmission
priorities between queues, the scheduler queues have to be
contiguous w.r.t their HW indices. So both contiguous and
non-contiguous allocations are supported.
Upon receiving NIX_TXSCH_FREE mbox msg all scheduler queues
allocated to sending PFFUNC (PF/VF) will be freed. Selective
free is not supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_detach_rsrcs':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:855:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:853:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_mbox_handler_ATTACH_RESOURCES':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1054:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1053:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
746ea74241 ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c: In function 'rvu_npa_init':
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c:446:20: warning:
variable 'block' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit 7a37245ef2 ("octeontx2-af: NPA block admin queue init")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all RQ/SQ/CQ
contexts of a NIX LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the RQ/SQ/CQ contexts.
So a bitmap is introduced to keep track of enabled NIX RQ/SQ/CQ
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NIX AQ
via mbox. Instructions can be to init/write/read RQ/SQ/CQ/RSS
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate bitmaps and memory for PFVF mapping info for
maintaining NIX transmit scheduler queues maintenance.
PF/VF drivers will request for alloc, free e.t.c of
Tx schedulers via mailbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Config LSO formats for TSOv4 and TSOv6 offloads.
These formats tell HW which fields in the TCP packet's
headers have to be updated while performing segmentation
offload.
Also report PF/VF drivers the LSO format indices as part
of response to NIX_LF_ALLOC mbox msg. These indices are
used in SQE extension headers while framing SQE for pkt
transmission with TSO offload.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NIX_LF_ALLOC mbox message allocate memory for
NIXLF's CQ, SQ, RQ, CINT, QINT and RSS HW contexts and configure
respective base iova HW. Enable caching of contexts into NIX NDC.
Return SQ buffer (SQB) size, this PF/VF MAC address etc info
e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NIX admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NIX LFs will submit
instructions to AQ to init/write/read RQ/SQ/CQ/RSS contexts
and in case of read, get context from result memory.
Also before configuring/using NIX block calibrate X2P bus
and check if NIX interfaces like CGX and LBK are in active
and working state.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all Aura/Pool
contexts of a NPA LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the Aura/Pool contexts.
So a bitmap is introduced to keep track of enabled NPA Aura/Pool
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NPA AQ
via mbox. Instructions can be to init/write/read Aura/Pool/Qint
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NPA_LF_ALLOC mbox message allocate memory for
NPALF's aura, pool and qint contexts and configure the same
to HW. Enable caching of contexts into NPA NDC.
Return pool related info like stack size, num pointers per
stack page e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NPA admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NPA LFs will submit
instructions to AQ to init/write/read Aura/Pool contexts
and in case of read, get context from result memory.
Added some common APIs for allocating memory for a queue
and get IOVA in return, these APIs will be used by
NIX AQ and for other purposes.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to enable or disable internal loopback mode in CGX.
New mbox IDs CGX_INTLBK_ENABLE/DISABLE added for this.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving notification from firmware the CGX event handler
in the AF driver gets the current link info such as status, speed,
duplex etc from CGX driver and sends it across to PFs who have
registered to receive such notifications.
To support above
- Mbox messaging support for sending msgs from AF to PF has been added.
- Added mbox msgs so that PFs can register/unregister for link events.
- Link notifications are sent to PF under two scenarioss.
1. When a asynchronous link change notification is received from
firmware with notification flag turned on for that PF.
2. Upon notification turn on request, the current link status is
send to the PF.
Also added a new mailbox msg using which RVU PF/VF can retrieve
their mapped CGX LMAC's current link info. Link info includes
status, speed, duplex and lmac type.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting MAC address filters in CGX
for PF interfaces. Also PF interfaces can be put in promiscuous
mode. Dataplane PFs access this functionality using mailbox
messages to the AF driver.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF driver to retrieve
it's mapped CGX LMAC Rx and Tx stats from AF via mbox.
New mailbox msg is added is added.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new mailbox msgs for RVU PF/VFs to request AF
to enable/disable their mapped CGX::LMAC Rx & Tx.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looping on a integer timeout, use time_before(jiffies),
so that maximum poll time is capped.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added driver causes a warning about a function that is
not used anywhere:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:320:12: error: 'cgx_fwi_link_change' defined but not used [-Werror=unused-function]
Remove it for now, until a user gets added. If we want to use this
function from another module, we also need a declaration in a header
file, which is currently missing, so it would have to change anyway.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c: In function 'cgx_fwi_event_handler':
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:257:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support in RVU AF driver to register for
CGX LMAC link status change events from firmware
and managing them. Processing part will be added
in followup patches.
- Introduced eventqueue for posting events from cgx lmac.
Queueing mechanism will ensure that events can be posted
and firmware can be acked immediately and hence event
reception and processing are decoupled.
- Events gets added to the queue by notification callback.
Notification callback is expected to be atomic, since it
is called from interrupt context.
- Events are dequeued and processed in a worker thread.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX LMAC initialization, link status polling etc is done
by low level secure firmware. For link management this patch
adds a interface or communication mechanism between firmware
and this kernel CGX driver.
- Firmware interface specification is defined in cgx_fw_if.h.
- Support to send/receive commands/events to/form firmware.
- events/commands implemented
* link up
* link down
* reading firmware version
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Nithya Mani <nmani@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
CGX ethernet interface driver. Just the probe.
RVU AF driver will use APIs exported by this driver
for various things like PF to physical interface mapping,
loopback mode, interface stats etc. Hence marged both
drivers into a single module.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW interprets RVU_AF_MSIXTR_BASE address as an IOVA, hence
create a IOMMU mapping for the physcial address configured by
firmware and reconfig RVU_AF_MSIXTR_BASE with IOVA.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a RVU PF/VF to request AF via mailbox
to attach or detach NPA/NIX/SSO/SSOW/TIM/CPT block LFs.
Also supports partial detachment and modifying current
LF attached count of a certian block type.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 10's of mailbox messages expected to be handled in future,
checking for message id could become a lengthy switch case. Hence
added a macro to auto generate the switch case for each msg id.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mailbox support infrastructure APIs.
Each RVU device has a dedicated 64KB mailbox region
shared with it's peer for communication. RVU AF has
a separate mailbox region shared with each of RVU PFs
and a RVU PF has a separate region shared with each of
it's VF.
These set of APIs are used by this driver (RVU AF) and
other RVU PF/VF drivers eg netdev, crypto e.t.c.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gathers NPA/NIX/SSO/SSOW/TIM/CPT RVU blocks's
HW info like number of LFs. Important register offsets
saved for later use to avoid code duplication for each block.
A bitmap is allocated for each of the blocks which later
on will be used to allocate a LF for a RVU PF/VF.
Also added RVU NIX/NPA block registers and few registers
of other blocks.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
resource virtualization unit (RVU) admin function (AF)
driver. Just the driver registration and probe.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.
The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.
This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.
The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.
Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit call to netif_carrier_off() in
mvneta_open() as this is already handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit call to netif_carrier_off() in PPv2's
open() path, as this is now handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch maps all uses of the CPU to threads. All this_cpu calls are
replaced, and all smp_processor_id() calls are wrapped into the
indirection.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the Marvell PPv2 driver to stop using directly the
CPU number to access per-thread registers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Marvell PPv2 driver the mvpp2_read_relaxed function is only used
in a single file. Make it static and remove its prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 driver has per-cpu functions. As they only are used in
the main file, make them static and remove their prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the PPv2 driver so that all CPU variables are unsigned, as it
makes no sense to have a negative CPU number. This patch is cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the probing function so that the queue mode isn't
updated while probing, as the driver would silently end up using a
configuration not wanted by the user. The patch adds an extra check to
validate the chosen queue mode instead, and the driver will fail to
probe if the configuration is invalid.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.
The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the number of s/w threads to 9, its maximum value,
instead of 8. This is not a fix as only 4 of the s/w threads were used
so far, but more could be used in the future.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the loop of mvneta_tx_done_gbe(), we call the smp_processor_id()
each time, move the call out of the loop to optimize the code a bit.
Before the patch, the loop looks like(under arm64):
ldr x1, [x29,#120]
...
ldr w24, [x1,#36]
...
bl 0 <_raw_spin_lock>
str w24, [x27,#132]
...
After the patch, the loop looks like(under arm64):
...
bl 0 <_raw_spin_lock>
str w23, [x28,#132]
...
where w23 is loaded so be ready before the loop.
>From another side, mvneta_tx_done_gbe() is called from mvneta_poll()
which is in non-preemptible context, so it's safe to call the
smp_processor_id() function once.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code and HW supports NETIF_F_RXCSUM, so let's enable it by default.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_receive() checks NETIF_F_GRO bit as well, if the bit is not
set, we will go through GRO_NORMAL in napi_skb_finish(), so fall back
to netif_receive_skb_internal(), so we don't need to check NETIF_F_GRO
ourself.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without a valid of_node in struct device we can't find the mvpp2 port
device by its DT node. Specifically, this breaks
of_find_net_device_by_node().
For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141
switch connected to the &cp1_eth2 port:
&cp1_mdio {
...
switch0: switch0@4 {
compatible = "marvell,mv88e6085";
...
ports {
...
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
};
};
};
};
Without this patch, dsa_register_switch() returns -EPROBE_DEFER because
of_find_net_device_by_node() can't find the device_node of the &cp1_eth2
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events, the driver uses
a per CPU napi structure for this case. Some SoCs such as armada 3700
have a single interrupt for Ethernet events, the driver uses a global
napi structure for this case.
Current mvneta_config_rss() always operates the per cpu napi structure.
Fix it by operating a global napi for "single interrupt" case, and per
cpu napi structure for remaining cases.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With system having a small memory (around 256MB), the state "cannot
allocate memory to refill with new buffer" is reach pretty quickly.
By this patch we changed buffer allocation method to a better handling of
this use case by avoiding memory allocation issues.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory: extract from a larger patch]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the checksum offload feature is not set, then there is no point to
check the status of the hardware.
[gregory: extract from a larger patch]
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of trying to allocate the exact amount of memory for each
descriptor use a page for each of them, it allows to simplify the
allocation management and increase the performance of the driver.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve the diagnostic in case of error, make the distinction
between refill error and skb allocation error. Also make the information
available through the ethtool state.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial values were too small leading to poor performance when using
the software buffer management.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory: extract from a larger patch]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On year ago Rob Herring wanted to remove the data pointer from the
device_node structure[1]. The mvneta driver seemed to be the only one
which used (abused ?) it. However, the proposal of Rob to remove this
pointer from the driver introduced a regression, and I tested and fixed an
alternative way, but it was never submitted as a proper patch.
Now here it is: Instead of using the device_node structure ->data
pointer, we store the BM private data as the driver data of the BM
platform_device. The core mvneta code can retrieve it by doing a lookup
on which platform_device corresponds to the BM device tree node using
of_find_device_by_node(), and get its driver data
[1]https://www.spinics.net/lists/netdev/msg445197.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is incorrect to enable TX/RX queues (call by mvneta_port_up()) for
port without link. Indeed MTU change for interface without link causes TX
queues to stuck.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory.clement: adding Fixes tags and rewording commit log]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events. Some SoCs have
a single interrupt, independent of the CPU. The driver handles this by
having a per CPU napi structure when there are per CPU interrupts, and
a global napi structure when there is a single interrupt.
When the napi core calls mvneta_poll(), it passes the napi
instance. This was not being propagated through the call chain, and
instead the per-cpu napi instance was passed to napi_gro_receive()
call. This breaks when there is a single global napi instance.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of the | operator always leads to true, which looks rather
suspect in this case.
Fix this by using & instead.
Addresses-Coverity-ID: 1471903 ("Wrong operator used")
Fixes: dba1d918da ("net: mvpp2: debugfs: add entries for classifier flows")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classification operations that are used for RSS make use of several
lookup tables. Having hit counters for these tables is really helpful
to determine what flows were matched by ingress traffic, and see the
path of packets among all the classifier tables.
This commit adds hit counters for the 3 tables used at the moment :
- The decoding table (also called lookup_id table), that links flows
identified by the Header Parser to the flow table.
There's one entry per flow, located at :
.../mvpp2/<controller>/flows/XX/dec_hits
Note that there are 21 flows in the decoding table, whereas there are
52 flows in the Header Parser. That's because there are several kind
of traffic that will match a given flow. Reading the hit counter from
one sub-flow will clear all hit counter that have the same flow_id.
This also applies to the flow_hits.
- The flow table, that contains all the different lookups to be
performed by the classifier for each packet of a given flow. The match
is done on the first entry of the flow sequence.
- The C2 engine entries, that are used to assign the default rx queue,
and enable or disable RSS for a given port.
There's one entry per flow, located at:
.../mvpp2/<controller>/flows/XX/flow_hits
There is one C2 entry per port, so the c2 hit counter is located at :
.../mvpp2/<controller>/ethX/c2_hits
All hit counter values are 16-bits clear-on-read values.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classifier configuration for RSS is quite complex, with several
lookup tables being used. This commit adds useful info in debugfs to
see how the different tables are configured :
Added 2 new entries in the per-port directory :
- .../eth0/default_rxq : The default rx queue on that port
- .../eth0/rss_enable : Indicates if RSS is enabled in the C2 entry
Added the 'flows' directory :
It contains one entry per sub-flow. a 'sub-flow' is a unique path from
Header Parser to the flow table. Multiple sub-flows can point to the
same 'flow' (each flow has an id from 8 to 29, which is its index in the
Lookup Id table) :
- .../flows/00/...
/01/...
...
/51/id : The flow id. There are 21 unique flows. There's one
flow per combination of the following parameters :
- L4 protocol (TCP, UDP, none)
- L3 protocol (IPv4, IPv6)
- L3 parameters (Fragmented or not)
- L2 parameters (Vlan tag presence or not)
.../type : The flow type. This is an even higher level flow,
that we manipulate with ethtool. It can be :
"udp4" "tcp4" "udp6" "tcp6" "ipv4" "ipv6" "other".
.../eth0/...
.../eth1/engine : The hash generation engine used for this
flow on the given port
.../hash_opts : The hash generation options indicating on
what data we base the hash (vlan tag, src
IP, src port, etc.)
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One helpful feature to help debug the Header Parser TCAM filter in PPv2
is to be able to see if the entries did match something when a packet
comes in. This can be done by using the built-in hit counter for TCAM
entries.
This commit implements reading the counter, and exposing its value on
debugfs for each filter entry.
The counter is a 16-bits clear-on-read value, located at:
.../mvpp2/<controller>/parser/XXX/hits
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: f9358e12a0 ("net: mvpp2: split ingress traffic into multiple flows")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows setting the RSS hash generation parameters from
ethtool. When setting parameters for a given flow type from ethtool
(e.g. tcp4), all the corresponding flows in the flow table are updated,
according to the supported hash parameters.
For example, when configuring TCP over IPv4 hash parameters to be
src/dst IP + src/dst port ("ethtool -N eth0 rx-flow-hash tcp4 sdfn"),
we only set the "src/dst port" hash parameters on the non-fragmented TCP
over IPv4 flows.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the classification action that can be performed is to compute a
hash of the packet header based on some header fields, and lookup a RSS
table based on this hash to determine the final RxQ.
This is done by adding one lookup entry per flow per port, so that we
can configure the hash generation parameters for each flow and each
port.
There are 2 possible engines that can be used for RSS hash generation :
- C3HA, that generates a hash based on up to 4 header-extracted fields
- C3HB, that does the same as c3HA, but also includes L4 info in the hash
There are a lot of fields that can be extracted from the header. For now,
we only use the ones that we can configure using ethtool :
- DST MAC address
- L3 info
- Source IP
- Destination IP
- Source port
- Destination port
The C3HB engine is selected when we use L4 fields (src/dst port).
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+---------+ +------------+ +--------------------------+ |
| RSS tbl |<--| Classifier |<--------| flow 0: C2 lookup | |
+---------+ +------------+ | C3 lookup port 0 | |
| | | C3 lookup port 1 | |
+-----------+ +-------------+ | ... | |
| C2 engine | | C3H engines | | flow 1: C2 lookup |<--+
+-----------+ +-------------+ | C3 lookup port 0 |
| ... |
| ... |
| flow 51 : C2 lookup |
| ... |
+--------------------------+
The C2 engine also gains the role of enabling and disabling the RSS
table lookup for this packet.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 classifier allows to perform classification operations on each
ingress packet, based on the flow the packet is assigned to.
The current code uses only 1 flow per port, and the only classification
action consists of assigning the rx queue to the packet, depending on the
port.
In preparation for adding RSS support, we have to split all incoming
traffic into different flows. Since RSS assigns a rx queue depending on
the hash of some header fields, we have to make sure that the hash is
generated in a consistent way for all packets in the same flow.
What we call a "flow" is actually a set of attributes attached to a
packet that depends on various L2/L3/L4 info.
This patch introduces 52 flows, wich are a combination of various L2, L3
and L4 attributes :
- Whether or not the packet has a VLAN tag
- Whether the packet is IPv4, IPv6 or something else
- Whether the packet is TCP, UDP or something else
- Whether or not the packet is fragmented at L3 level.
The flow is associated to a packet by the Header Parser. Each flow
corresponds to an entry in the decoding table. This entry then points to
the sequence of classification lookups to be performed by the
classifier, represented in the flow table.
For now, the only lookup we perform is a C2 lookup to set the default
rx queue.
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+------------+ +---------------------+ |
To RxQ <---| Classifier |<-------| flow 0: C2 lookup |<--------+
+------------+ | flow 1: C2 lookup |
| | ... |
+------------+ | flow 51 : C2 lookup |
| C2 engine | +---------------------+
+------------+
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 Controller has a classifier, that can perform multiple lookup
operations for each packet, using different engines.
One of these engines is the C2 engine, which performs TCAM based lookups
on data extracted from the packet header. When a packet matches an
entry, the engine sets various attributes, used to perform
classification operations.
One of these attributes is the rx queue in which the packet should be sent.
The current code uses the lookup_id table (also called decoding table)
to assign the rx queue. However, this only works if we use one entry per
port in the decoding table, which won't be the case once we add RSS
lookups.
This patch uses the C2 engine to assign the rx queue to each packet.
The C2 engine is used through the flow table, which dictates what
classification operations are done for a given flow.
Right now, we have one flow per port, which contains every ingress
packet for this port.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp22_init_rss function configures the RSS parameters for each port, so
rename it accordingly. Since this function relies on classifier
configuration, move its call right after the classifier config.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling the RSS table, we have to make sure that the rx queue is
attached to an online CPU.
This patch is not a full support for cpu_hotplug, but rather a way to
make sure that we don't break network on system booted with the maxcpus
parameter.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an extra indirection when setting the indirection table
into the RSS hardware table to improve the packets distribution across
CPUs. For example, if 2 queues are used on a multi-core system this new
indirection will choose two queues on two different CPUs instead of the
two first queues which are on the same first CPU.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RSS indirection table support, allowing to use the
ethtool -x and -X options to dump and set this table.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Maxime: Small warning fixes, use one table per port]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 Controller has 8 RSS Tables, of 32 entries each. A lookup in the
RXQ2RSS_TABLE is performed for each incoming packet, and the RSS Table
to be used is chosen according to the default rx queue that would be
used for the packet.
This default rx queue is set in the Lookup_id Table (also called
Decoding Table), and is equal to the port->first_rxq.
Since the Classifier itself isn't active at any time for the moment,
this doesn't have a direct effect, the default rx queue at the moment is
the one where all packets end-up into.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no RSS_TABLE register in PPv2 Controller. The register 0x1510
which was specified is actually named "RSS_HASH_SEL", but isn't used by
this driver at all.
Based on how this register was used, it should have been the
RXQ2RSS_TABLE register, which allows to select the RSS table that will
be used for the incoming packet.
The RSS_TABLE_POINTER is actually a field of this RXQ2RSS_TABLE
register.
Since RSS tables are actually not used by the driver for now, this
commit does not fix a runtime bug.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch fixing a typo in one of the RSS comments.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of receive queue per port is :
- MVPP2_DEFAULT_RXQ if in single queue mode
- MVPP2_DEFAULT_RXQ * num_possible_cpus if in multi queue mode
with MVPP2_DEFAULT_RXQ = 4.
However, we don't use the extra rx queues at the moment, we really only
need one per port per CPU, until some more advanced classification rules
are implemented.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a dedicated #define that indicates the number of rx queues per
port per cpu, this commit removes a harcoded use of that value
This doesn't fix any runtime bugs since the harcoded value matches the
expected value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RSS only applies when we have per-cpu rx queues, it should only
be enabled when the driver is configured to make use of multi-queue
mode.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi queue mode is needed to have RSS available, and offers some
nice advantages, being able to have one rx queue vector per CPU.
This mode has been usable through the use of a module parameter, this
commit makes it the default value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 driver defines 2 "queue_modes" :
- QDIST_SINGLE_MODE, where each port share one rx queue vector
between all CPUs
- QDIST_MULTI_MODE, where each port has one rx queue vector per CPU.
Multi queue mode isn't available on PPv2.1, make sure we fallback to
single mode when running on this revision.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the the RSS indirection tables should be defined in mvpp2.h,
so that we can use it in all files of the PPv2 driver.
This commit moves the define in mvpp2.h, and adds the missing #include
in mvpp2_cls.h.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include guards should be put before #includes. This doesn't fix any bug,
but prevent future compilation issues when adding new files in the mvpp2
driver
The Header Parser init function needs the platform_device definition,
and with the fixed include guards we need to add the missing include.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 driver uses interrupts and tasklet but does not
explicitly include linux/interrupt.h, relying on implicit includes. This
one particularly is included by chance after a long unlogical chain of
inclusions. Fix this so we do not get future build breaks.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the skb->protocol field, we have to make sure we use the
proper endianness using htons, and not swab16.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan IDs must not be swapped when creating Header Parser entries. This
has no effect on little-endian systems, but is wrong for big-endian.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2's Header Parser use some large TCAM and SRAM entries, that are
duplicated in software so that we can write them to hardware only when
we are done modifying them.
Currently, PPv2 uses a union containing arrays of u32 and u8 to represent
these entries, to facilitate byte per byte access. This representation is
broken when we want to support big endian, and this makes the code
confusing to read.
This patch drops the union, and simply stores the TCAM and SRAM entries
as u32 arrays, each entry corresponding to a 32-bit register.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller always expect descriptors to be in little endian. We
must therefore force descriptors to use that format, and convert to the
host endianness when necessary.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using s/w buffer management, buffers are allocated and DMA mapped.
When doing so on an arm64 platform, an offset correction is applied on
the DMA address, before storing it in an Rx descriptor. The issue is
this DMA address is then used later in the Rx path without removing the
offset correction. Thus the DMA address is wrong, which can led to
various issues.
This patch fixes this by removing the offset correction from the DMA
address retrieved from the Rx descriptor before using it in the Rx path.
Fixes: 8d5047cf9c ("net: mvneta: Convert to be 64 bits compatible")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: db9d7d36ee ("net: mvpp2: Split the PPv2 driver to a dedicated directory")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Header Parser sets some bits in the 'result_info' field in
each lookup iteration, to identify different packet attributes such as
DSA / VLAN tag, protocol infos, etc. This is used in further
classification stages in the controller.
It's the DSA tag detection entry that is in charge of detecting when there
is a single VLAN tag.
This commits adds the missing update of the result_info in this case.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch on the Marvell PPv2 driver is only cosmetic. Two typos are
removed as well as other cosmetic fixes, such as extra new lines or tabs
vs spaces.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent flood of RX error prints during heavy traffic with weak signal
in link by checking net_ratelimit() before using netdev_err().
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: small rework, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special stop/start handling from the set_mac_address callback.
All this special care is not needed, and can be removed. It also
simplifies the up/down status in the driver and helps avoiding possible
link status mismatch issues.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid repeating the check for free aggregated descriptors when it
already failed at the beginning of the function.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.
The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.
The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2.2 IP needs an additional clock named "MG Core clock".
This is required on Armada 7K and 8K.
This commit adds the required clock in mvpp2, making sure it's only
used on PPv2.2.
Fixes: c7e92def1e ("clk: mvebu: cp110: Fix clock tree representation")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When clk_prepare_enable fails for the axi_clk, the mg_clk isn't properly
cleaned up. Add another jump label to handle that case, and make sure we
jump to it in the later error cases.
Fixes: 4792ea04bc ("net: mvpp2: Fix clock resource by adding an optional bus clock")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.
The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.
This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.
Fixes: 10fea26ce2 ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boundary check in mvpp2_prs_init_from_hw must be done according to the
passed "tid" parameter, not the mvpp2_prs_entry index, which is not yet
initialized at the time of the check.
Fixes: 47e0e14eb1 ("net: mvpp2: Make mvpp2_prs_hw_read a parser entry init function")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current suspend/resume implementation reuses the mvneta_open() and
mvneta_close(), but it could be optimized to take only necessary
actions during suspend/resume.
One obvious problem of current implementation is: after hundreds of
system suspend/resume cycles, the resume of mvneta could fail due to
fragmented dma coherent memory. After this patch, the non-necessary
memory alloc/free is optimized out.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare the suspend/resume improvement in next patch. The
SW parts can be optimized out during resume.
As for rxq handling during suspend, we'd like to drop packets by
calling mvneta_rxq_drop_pkts() which is both SW and HW operation,
so we don't split rxq deinit.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 ethernet stops working after system resume from suspend:
[ 582.852065] sky2 0000:04:00.0: Refused to change power state, currently in D3
The current 150ms delay is not enough, change it to 200ms can solve the
issue.
BugLink: https://bugs.launchpad.net/bugs/1758507
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.
q_map must be ZERO in the beginning of this process.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The style of the rx/tx queue's *_coal member assignment is:
static void foo_coal_set(...)
{
set the coal in hw;
update queue's foo_coal member; [1]
}
In other place, we call foo_coal_set(pp, queue->foo_coal), so the above [1]
is duplicated and could be removed.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use relaxed I/O on the hot path. This achieves significant performance
improvements. On a 10G link, this makes a basic iperf TCP test go from
an average of 4.5 Gbits/sec to about 9.40 Gbits/sec.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message, cosmetic changes]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helper functions that search for given entries in the TCAM filter
on PPv2 controller make use of dynamically alloced temporary variables,
allocated with GFP_KERNEL. These functions can be called in atomic
context, and dynamic alloc is not really needed in these cases anyways.
This commit gets rid of dynamic allocs and use stack allocation in the
following functions, and where they're used :
- mvpp2_prs_flow_find
- mvpp2_prs_vlan_find
- mvpp2_prs_double_vlan_find
- mvpp2_prs_mac_da_range_find
For all these functions, instead of returning an temporary object
representing the TCAM entry, we simply return the TCAM id that matches
the requested entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_hw_read function uses the 'index' field of the struct
mvpp2_prs_entry to initialize the rest of the fields. This makes it
unclear from a caller's perspective, who needs to manipulate a struct
that is not entirely initialized.
This commit makes it an init function for prs_entry, by passing it the
index as a parameter. The function now zeroes the entry, and sets the
index field before doing all other init from HW.
The function is renamed 'mvpp2_prs_init_from_hw' to make that clear.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array mvpp2_pools is being indexed by long_log_pool, however this
looks like a cut-n-paste bug and in fact should be short_log_pool.
Detected by CoverityScan, CID#1466113 ("Copy-paste error")
Fixes: 576193f2d5 ("net: mvpp2: jumbo frames support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: effbf5f58d ("net: mvpp2: update the BM buffer free/destroy logic")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for jumbo frames in the Marvell PPv2 driver.
A third buffer pool is added with 10KB buffers, which is used if the MTU
is higher than 1518B for packets larger than 1518B. Please note only the
port 0 supports hardware checksum offload due to the Tx FIFO size
limitation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NETIF_F_IPV6_CSUM to the driver's features to enable
UDP/TCP checksum over IPv6. No extra configuration of the engine is
needed on top of the IPv4 counterpart, which already is in the features
list (NETIF_F_IP_CSUM).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the Tx FIFO data size on port 0 to 10kB. This prepares
the PPv2 driver for the Jumbo frame support addition as the hardware
will need big enough Tx FIFO buffers when dealing with frames going
through an interface with an MTU of 9000.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small reworks.]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer free routine is updated to release only given a number of
buffers, and the destroy routine now checks the actual number of buffers
in the (BPPI and BPPE) HW counters before draining the pools. This
change helps getting jumbo frames support.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures the buffer manager long pool for all ports part of
the same CP. Long pool separation between ports is redundant since there
are no performance improvement when different pools are used.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller allows for generic packet filtering. This commit
adds entries to implement VLAN filtering. The approach taken is :
- Filter entries that would match on the presence of the VLAN tag
(existing VLAN detection, DSA / EDSA detection) will set the next
lookup ID to be for the VID.
- For each VLAN existing on a given port, we add an entry that matches
this specific VID. If the incoming packet matches the VID entry, it is
set for the next lookup in the chain (LU_L2).
- A Guard entry is added for each port, that will match if the incoming
packet didn't match any of the above VID entries. This entry tags the
packet to be dropped.
Due to this design, and the fact that the total 256 filter entries are
also used for other purposes, we have a limit of 10 VLANs per port. To
accommodate the case where we would need more VLANS on one port, this
patch implements the ndo_set_features to allow for disabling of VLAN
filtering using ethtool.
The default config has VLAN filtering disabled.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements ndo_poll_controller callback which is necessary to
enable netconsole.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an alternative way of obtaining resources - via
ACPI tables provided by firmware. Enabling coexistence with the DT
support, in addition to the OF_*->device_*/fwnode_* API replacement,
required following steps to be taken:
* Add mvpp2_acpi_match table
* Omit clock configuration and obtain tclk from the property - in ACPI
world, the firmware is responsible for clock maintenance.
* Disable comphy and syscon handling as they are not available for ACPI.
* Modify way of obtaining interrupts - use newly introduced
fwnode_irq_get() routine
* Until proper MDIO bus and PHY handling with ACPI is established in the
kernel, use only link interrupts feature in the driver. For the RGMII
port it results in depending on GMAC settings done during firmware
stage.
* When booting with ACPI MVPP2_QDIST_MULTI_MODE is picked by
default, as there is no need to keep any kind of the backward
compatibility.
Moreover, a memory region used by mvmdio driver is usually placed in
the middle of the address space of the PP2 network controller.
The MDIO base address is obtained without requesting memory region
(by devm_ioremap() call) in mvmdio.c, later overlapping resources are
requested by the network driver, which is responsible for avoiding
a concurrent access.
In case the MDIO memory region is declared in the ACPI, it can
already appear as 'in-use' in the OS. Because it is overlapped by second
region of the network controller, make sure it is released, before
requesting it again. The care is taken by mvpp2 driver to avoid
concurrent access to this memory region.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF functions can be used only for the driver using DT.
As a preparation for introducing ACPI support in mvpp2
driver, use struct fwnode_handle in order to obtain
properties from the hardware description.
This patch replaces of_* function with device_*/fwnode_*
where possible in the mvpp2.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'port_count' field of the mvpp2 structure holds an overall amount
of available ports, based on DT nodes status. In order to be prepared
to support other HW description, obtain the value by incrementing it
upon each successful port initialization. This allowed for simplifying
port indexing in the controller's private array, whose size is now not
dynamically allocated, but fixed to MVPP2_MAX_PORTS.
This patch simplifies creating and filling list of enabled ports and
is a part of the preparation for adding ACPI support in the mvpp2 driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the SFF module's EEPROM via the ethtool API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PSC sync change interrupt can fire multiple times while the link is
down, which is caused by noise on the serdes lines. As this isn't
information we make use of, it's pointless having the interrupt enabled.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port configuration and release of reset to mvneta_mac_config()
along side the rest of the port mode configuration.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mvneta to use phylink, which models the MAC to PHY link in
a generic, reusable form.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove unused sync status
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare to convert mvneta to phylink by splitting the adjust_link
function into its consituent parts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev core always ensures that the rtnl lock is held while calling
the ndo_open() and ndo_stop() methods. However, the suspend/resume paths
do not hold the rtnl lock. phylink will expect the rtnl lock to be held
when the MAC driver calls it, so we end up with kernel warnings. Take
the lock to ensure that these functions are called in a consistent
manner.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2_vpd_wait is not called in an interrupt handler nor holding a spinlock.
The function mdelay in it can be replaced with msleep, to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: stable@vger.kernel.org
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and fixes tag]
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: <stable@vger.kernel.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes: 1d17db08c0 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller provides a 8-bit register to update the pending
Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be
added at once. In the current code the mvneta_txq_pend_desc_add function
assumes the caller takes care of this limit. But it is not the case. In
some situations (xmit_more flag), more than 255 descriptors are added.
When this happens, the Tx descriptor counter register is updated with a
wrong value, which breaks the whole Tx queue management.
This patch fixes the issue by allowing the mvneta_txq_pend_desc_add
function to process more than 255 Tx descriptors.
Fixes: 2a90f7e1d5 ("net: mvneta: add xmit_more support")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GOP statistics from all ports of one instance of the driver are gathered
with one work recalled in loop in a workqueue. The loop is started when
a port is up, and stopped when a port is down. This last condition is
obviously wrong.
Fix this by having a work per port. This way, starting and stoping it
when the port is up or down will be fine, while minimizing unnecessary
CPU usage.
Fixes: 118d6298f6 ("net: mvpp2: add ethtool GOP statistics")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two functions were always used to set the DMA addresses in Tx
descriptors, because this address is split into a base+offset in the
descriptors. A mask was used to come up with the base and offset
addresses and two functions were called, mvpp2_txdesc_dma_addr_set() and
mvpp2_txdesc_offset_set().
This patch moves the base+offset calculation logic to
mvpp2_txdesc_dma_addr_set(), and removes mvpp2_txdesc_offset_set() to
simplify things.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch using the MVPP2_AGGR_TXQ_SIZE everywhere instead of the
size field of aggr_txq, as the size never change and is always equal to
the MVPP2_AGGR_TXQ_SIZE define.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many TSO descriptors can be required for the default queue size,
when using small MSS values for example. Prevent this by adding a
maximum number of allowed TSO segments (300). In addition set a stop and
a wake thresholds to stop the queue when there's no room for a 1 "worst
case scenario skb". Wake up the queue when the number of descriptors is
low enough.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialize the RSS tables to evenly (depending on the packets
RSS hashes) distribute the packets across port Rx queues. This helps to
handle packets on different CPUs to improve performances, as more queues
will be used in parallel.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the Rx FIFO size was initialized. For PPv2.2 the Tx FIFO
size can be set as well. This patch initializes the Tx FIFO size for
PPv2.2 controllers to 3K.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx FIFO size was set to the same value for all ports. This patch
sets it depending on the maximum speed a given port can handle. This is
only working for PPv2.2.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham