The SyncTimer in AM43x is clocked using the following two sources:
1) An inaccuarte 32k clock (CLK_32KHZ) derived from PER DPLL, causing system
time to go slowly (~10% deviation).
2) external 32KHz RTC clock, which may not always be available on board like
in the case of ePOS EVM
Use gptimer as clocksource instead, as is done in the case of AM335x
(which does not have a SyncTimer). With this, system time keeping works
accurately.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine AM43x device features by reusing AM335x helper as feature
register layout is similar.
And also exporting AM43xx family name.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.
sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.
Add quirks code to handle proper reset pulse signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_noncore_dpll_set_rate forces a reparent to the same clk_ref
for every call that takes place. This is an can be done only if a change
is detected.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Printing with unsigned long rates with %ld gives wrong result if the
rate is high enough. Fix this by using %lu.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has a spinlock module which is identical to the
one present on AM33xx. Register the spinlock ocp_if link
so that the spinlock hwmod and associated omap_device can
be instantiated, and the runtime pm API could be used by
the OMAP hwspinlock driver.
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since commit 65aa94b204 (ARM: OMAP4: clockdomain/CM code: Update supported
transition modes), on OMAP4, all CLKDMs support HW_AUTO so this is used
instead of SW_SLEEP for the idling of clockdomains. However, additional
SoCs now leverage the OMAP4 clockdomain code so update it to use SW_SLEEP
if the clockdomain data specifies that the CLKDM has the
CLKDM_CAN_FORCE_SLEEP flag set rather than using HW_AUTO for both cases.
Without this patch, clockdomain handling is broken on AM43xx and no
clockdomains are actually being put into idle on this platform. Any
attempt to idle them results in the HW_AUTO value (0x3) being written
to them with no apparent effect.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: added extra explanatory text from patch set intro]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add restart hook so that AM4372 builds can restart the platform.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTBT1nAAoJEMhvYp4jgsXikI0IAIv2GmBCgbg0XhHZBSheSNOh
Th1bv4KeEci/3uezwVTAA3AtJIvDNMAQjRYjNSyOnCCC7s5czex1w/Mk/6IzgX8C
eCauM5kiOV3ZKPMbPI6gxg0bmFe+YzWREbm7fpAqxpc3IXwzYlShnq/kKISq25Qj
mRZtv97AB2xqAy9zTyy18y+c+F/1mAgd+NeiDbjBimHbTK4urjiD7PpcWvmbYZld
H9Qw4d9JwVTRpRHw9PRR9glnvFYiFpp+s9ehSjcyYi8wjZKO1+67c56fS+ScsoV7
qM4J2qtS2kpzvyFvOI7wY6E2M5Es7zOeuJAmh0jEkbDtRa0a4YFYL0DAp5k9Xiw=
=NEez
-----END PGP SIGNATURE-----
Merge tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/cleanup
Merge "kconfig clean-up and mach-virt removal for 3.15" from Rob Herring
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
* tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: virt: select ARM_AMBA
ARM: virt: make mach-virt just a kconfig option
ARM: vt8500: enable V6K instead of plain V6
ARM: cns3xxx: enable V6K instead of plain V6
ARM: bcm2835: enable V6K instead of plain V6
ARM: Select V6K instead of V6 by default for multi-platform
ARM: select MIGHT_HAVE_CACHE_L2X0 for V6 and V7 multi-platform
ARM: select HAVE_SMP for V7 multi-platform
ARM: centralize common multi-platform kconfig options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=2y5d
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes from Tony Lindgren:
Fixes for omaps mostly to fix the 3430 display regression,
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
* tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix pinctrl interrupts for core2
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omapdss driver no longer uses get_context_loss_count call, so we can
remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
After splitting padconf core into two parts to avoid exposing
unaccessable registers, the new padconf core2 domain was left
without a wake-up interrupt.
Fix the issue by passing the shared wake-up interrupt in
platform data like we do for padconf core and wkup domains
already.
Fixes: 3d49538364 (ARM: dts: Split omap3 pinmux core device)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Delete ARM's asm/system.h. It's the last holdout and should be got rid of.
This builds for defconfig, lpc32xx_defconfig, exynos_defconfig + XEN, the
previous changed to a Gemini system and an omap3 config with TI_DAVINCI_EMAC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The camera sensor will soon require regulators and clocks. Register
fixed regulators for its VAA and VDD power supplies and a fixed rate
clock for its master clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
for non SMP build, NR_CPUS is 1 and hence the code complains with below
warnings.
arch/arm/mach-omap2/cpuidle44xx.c:207:8: warning: array subscript is above array bounds [-Warray-bounds]
arch/arm/mach-omap2/cpuidle44xx.c:212:11: warning: array subscript is above array bounds [-Warray-bounds]
Kill it by making array size fixed.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
reboot fix in there, plus a clock fix for rate computations involving
x2 multipliers.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/
Note that most full-chip PM is broken since the v3.14 merge; it's
not caused by this series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aMQk
-----END PGP SIGNATURE-----
Merge tag 'for-v3.14-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.14/fixes
Several OMAP clock/PM/device data fixes for v3.14-rc. There's an OMAP5
reboot fix in there, plus a clock fix for rate computations involving
x2 multipliers.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.14-rc/20140219131753/
Note that most full-chip PM is broken since the v3.14 merge; it's
not caused by this series.
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling
clk_set_rate() on the clock "skips" the x2 multiplier as there are no
set_rate and round_rate functions defined for the clkoutx2.
This results in getting double the requested clock rates, breaking the
display on omap3430 based devices. This got broken when
d0f58bd3bb and related patches were merged
for v3.14, as omapdss driver now relies more on the clk-framework and
CLK_SET_RATE_PARENT.
This patch implements set_rate and round_rate for clkoutx2.
Tested on OMAP3430, OMAP3630, OMAP4460.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 313a76e (ARM: OMAP2+: hwmod: Fix SOFTRESET logic) introduced
softreset bit cleaning right after set one. It is caused L3 error for
OMAP4 ISS because ISS register write occurs when ISS reset process is in
progress. Avoid this situation by cleaning softreset bit later, when reset
process is successfully finished.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The spinlock module's SYSCONFIG register on DRA7xx does not
support smart wakeup, and also does not have the CLKACTIVITY
field. The sysc data for spinlock module has been appropriately
fixed up to reflect the same.
Cc: Ambresh K <ambresh@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the correct register offset for issuing the
reset command in OMAP5. Since dev_inst is set dynamically
OMAP4 should not be affected by this change.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@gmail.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were just
removed. Selecting them is a nop. The select statements for these
symbols can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 97411608fd ("ARM: OMAP2+: Remove legacy support for zoom
platforms") removed the Kconfig symbols MACH_OMAP_ZOOM2 and
MACH_OMAP_ZOOM3. Remove the last usage of the related macros too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The last caller of machine_is_nokia_n800() was removed in commit
5a87cde490 ("ARM: OMAP2+: Remove legacy booting support for n8x0").
That means that the Kconfig symbol MACH_NOKIA_N800 is now unused. It can
safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit 75d3625e0e
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).
Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: commit bc6b1e7b86
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).
Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.
This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m
CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wakeup gen mask/unmask callback uses the irq element of the
irq_data to setup. The irq is the linux virtual irq number and
is same as the hardware irq number only when the parent irqchip
is setup as a legacy domain. When it is used as a linear domain,
the virtual irqs are allocated dynamically and wakeup gen code
cannot rely on these numbers to access the irq registers. Instead
use the hwirq element of the irq_data which represent the physical
irq number.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The selection of HAVE_ARM_TWD for OMAP and shmobile depend on LOCAL_TIMER
which no longer exists. They should depend on SMP instead.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases coverage
of the multiplatform defconfig and some DTS changes that plumbs up some
of the devices that now have bindings and driver support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ymAC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a set of patches for (hopefully) -rc1. Some of them are fixes,
but a good number of them also do things such as enable new drivers in
the defconfigs for platforms that have such devices, increases
coverage of the multiplatform defconfig and some DTS changes that
plumbs up some of the devices that now have bindings and driver
support.
The commit dates are recent; we've mostly collected these fixes in the
last few days but I also had to rebuild the branch yesterday to sort
out some internal conflicts which reset the timestamps. The changes
should have been tested by each platform maintainer already (and few
of them have cross-platform impact) so I'm personally not too
concerned by it at this time"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
ARM: multi_v7_defconfig: add mvebu drivers
clocksource: kona: Add basic use of external clock
drivers: bus: fix CCI driver kcalloc call parameters swap
ARM: dts: bcm28155-ap: Fix Card Detection GPIO
ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
ARM: dts: zynq: Add SDHCI nodes
ARM: hisi: don't select SMP
ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
ARM: multi_v7: copy most options from tegra_defconfig
ARM: iop32x: fix power off handling for the EM7210 board
ARM: integrator: restore static map on the CP
ARM: msm_defconfig: Enable MSM clock drivers
ARM: dts: msm: Add clock controller nodes and hook into uart
ARM: OMAP4+: move errata initialization to omap4_pm_init_early
ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
...
Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The same workaround as ff999b8a09
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more
Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for Samsung
chips. Additionally there are other smaller clock driver changes and
several last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRJD
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
This branch is reducing in size for every release since most board-related
changes have started happening in devicetrees now. Still, we have some things
going on here.
* Renesas platforms are still adding a bit more legacy device support, something
that should trail off shortly as they move to full DT.
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a handful of old
code is being removed here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wLdE
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch is reducing in size for every release since most
board-related changes have started happening in devicetrees now.
Still, we have some things going on here.
* Renesas platforms are still adding a bit more legacy device
support, something that should trail off shortly as they move to
full DT
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a
handful of old code is being removed here"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: bcm2835: bcm2835_defconfig updates
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: exynos_defconfig: Enable S2MPS11 voltage regulator
ARM: tegra: Enable DRM panel support
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
...
Conflicts:
arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they came in
quite late and we decided to keep them deferred until the first -stable
release to get more coverage instead of squeezing them into 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QhN9
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
Pull ARM updates from Russell King:
"In this set, we have:
- Refactoring of some of the old StrongARM-1100 GPIO code to make
things simpler by Dmitry Eremin-Solenikov
- Read-only and non-executable support for modules on ARM from Laura
Abbot
- Removal of unnecessary set_drvdata() calls in AMBA code
- Some non-executable support for kernel lowmem mappings at the 1MB
section granularity, and dumping of kernel page tables via debugfs
- Some improvements for the timer/clock code on Footbridge platforms,
and cleanup some of the LED code there
- Fix fls/ffs() signatures to match x86 to prevent build warnings,
particularly where these are used with min/max() macros
- Avoid using the bootmem allocator on ARM (patches from Santosh
Shilimkar)
- Various asid/unaligned access updates from Will Deacon"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (51 commits)
ARM: SMP implementations are not supposed to return from smp_ops.cpu_die()
ARM: ignore memory below PHYS_OFFSET
Fix select-induced Kconfig warning for ZBOOT_ROM
ARM: fix ffs/fls implementations to match x86
ARM: 7935/1: sa1100: collie: add gpio-keys configuration
ARM: 7932/1: bcm: Add DEBUG_LL console support
ARM: 7929/1: Remove duplicate SCHED_HRTICK config option
ARM: 7928/1: kconfig: select HAVE_EFFICIENT_UNALIGNED_ACCESS for CPUv6+ && MMU
ARM: 7927/1: dcache: select DCACHE_WORD_ACCESS for big-endian CPUs
ARM: 7926/1: mm: flesh out and fix the comments in the ASID allocator
ARM: 7925/1: mm: keep track of last ASID allocation to improve bitmap searching
ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE
ARM: PCI: add legacy IDE IRQ implementation
ARM: footbridge: cleanup LEDs code
ARM: pgd allocation: retry on failure
ARM: footbridge: add one-shot mode for DC21285 timer
ARM: footbridge: add sched_clock implementation
ARM: 7922/1: l2x0: add Marvell Tauros3 support
ARM: 7877/1: use built-in byte swap function
ARM: 7921/1: mcpm: remove redundant dsb instructions prior to sev
...
the padconf area are not accessible and used for other devices.
Also fix the interrupt number for omap2 RNG, and add basic support
for sbc-3xxx with cm-t3730.
Note that the minor merge conflicts for omap_hwmod_2xxx_ipblock_data.c
can be solved by just dropping the legacy hwmod data for interrupts
for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=sPMZ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
Split omap3 core padconf area into two as some of the registers in
the padconf area are not accessible and used for other devices.
Also fix the interrupt number for omap2 RNG, and add basic support
for sbc-3xxx with cm-t3730.
Note that the minor merge conflicts for omap_hwmod_2xxx_ipblock_data.c
can be solved by just dropping the legacy hwmod data for interrupts
for v3.14.
* tag 'omap-for-v3.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: dts: Add support for sbc-3xxx with cm-t3730
Signed-off-by: Olof Johansson <olof@lixom.net>
Switch to memblock interfaces for early memory allocator instead of
bootmem allocator. No functional change in beahvior than what it is in
current code from bootmem users points of view.
Archs already converted to NO_BOOTMEM now directly use memblock
interfaces instead of bootmem wrappers build on top of memblock. And
the archs which still uses bootmem, these new apis just fallback to
exiting bootmem APIs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP3 platforms support both DT and non-DT boot at the moment, make
the clock init work according to the used setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
AM33xx clocks have now been moved to DT, thus remove the old data file
and use the new init code under OMAP clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Initializes clock data from device tree.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Initializes clock data from device tree.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP4 clocks have now been moved to DT, thus remove the old data file
and use the new init code under drivers/clk/omap/clk-44xx.c.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_init is now separated to a common function which gets called for all
SoC:s, which initializes the DT clocks and calls the SoC specific clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch provides top level functionality for the DT clock initialization.
Clock tree is initialized hierarchically starting from IP modules (CM/PRM/PRCM)
going down towards individual clock nodes, and finally initializing
clockdomains once all the clocks are ready.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DT clocks are mostly missing clkdm info now, and this causes an issue with
counter32k which makes its slave idlemode wrong and prevents core idle.
Fixed by initializing the hwmod clkdm pointers for omap3 also which makes
sure the clkdm flag matching logic works properly.
This patch also changes the return value for _init_clkdm to 0 for
incorrect clkdm_name, as this a warning, not a fatal error.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If the main clock for a hwmod is of basic clock type, it is illegal to type
cast this to clk_hw_omap and will result in bogus data. Fixed by checking
the clock flags before attempting the type cast.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clock nodes shall use the services provided by underlying drivers to access
the hardware registers instead of direct memory read/write. Thus, change
all the code to use the new omap2_clk_readl / omap2_clk_writel APIs for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Using indexed memmaps is required for isolating the actual memory access
from the clock code. Now, the driver providing the support for the clock IP
block provides the low level routines for reading/writing clock registers
also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-54xx.c now contains the clock init functionality for omap5, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-44xx.c now contains the clock init functionality for omap4, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a multipurpose clock node, which contains support for multiple
sub-clocks. Uses basic composite clock type to implement the actual
functionality, and TI specific gate, mux and divider clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
TI clk driver now routes some of the basic clocks through own
registration routine to allow autoidle support. This routine just
checks a couple of device node properties and adds autoidle support
if required, and just passes the registration forward to basic clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The OMAP clock driver now supports DPLL clock type. This patch also
adds support for DT DPLL nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
SOC_DRA7XX was under wrong menu within Kconfig file, which prevented
DRA7XX only build. Fixed the kconfig options for this SoC as we are
there. voltage.c needs to be added to the DRA7XX build also, otherwise
DRA7XX only build will fail.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DRA7XX and AM43XX were missing common clock code from the Makefile, which
causes build breakage in DRA7XX / AM43XX only builds once clock support
for these SoCs is added. Add the missing entries to the Makefile as
preparation of this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull ARM fixes from Russell King:
"Another few fixes for ARM, nothing major here"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
ARM: 7939/1: traps: fix opcode endianness when read from user memory
ARM: 7937/1: perf_event: Silence sparse warning
ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match
Revert "ARM: 7908/1: mm: Fix the arm_dma_limit calculation"
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After the introduction of gpmc_set_legacy(), move the GPMC width setting
to be done inside it. Currently, in the DT probed case, this is (wrongly)
done twice: first at gpmc_read_settings_dt(), and then based in the
NAND width setting.
Fix this and use only the value obtained from the DT.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce a helper function to complete the setting of some GPMC
parameters, only used when the gpmc is probed from a board file.
As such, it will go away once the DT conversion is completed.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit moves a bunch of initialization previously enclosed
under a 'if (gpmc_t)' check, to be outside such condition.
These initializations are not related to gpmc_t (timings) in any way
so it's nonsense to enclose them under such check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have standardized SoC definitions, update the
compatibility strings in board machine descriptors. Eventually, we
should just have SoC compatiblity here and all board specific stuff
should disappear.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next/boards
Need a newer base version to get a regulator fix for Samsung platforms that
they enable building in a defconfig.
Linux 3.13-rc5
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=kOrX
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Fixes: 7dedd34694 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Uwe Kleine-König:
* efm32/soc: (1003 commits)
ARM: device trees for Energy Micro's EFM32 Cortex-M3 SoCs
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
+Linux 3.13-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
While <mach/timex.h> isn't used for multi-platform builds since long it
still is for "normal" builds. As the previous patches fix all sites to
not make use of this per-platform file, it can go now for good also for
platforms that are not (yet) converted to multi-platform.
While at it there are no users of CLOCK_TICK_RATE any more, so also drop
the dummy #define.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This adds support for CompuLab SBC-T3530, also known as cm-t3730:
http://compulab.co.il/products/sbcs/sbc-t3530/
It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:
http://compulab.co.il/products/sbcs/sbc-t3517/http://compulab.co.il/products/sbcs/sbc-t3730/
So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.
I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.
Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.
Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit e30b06f4d5 (ARM: OMAP2+: Remove
legacy mux code for display.c) removed non-DT DSI and HDMI pinmuxing.
However, DSI pinmuxing is still needed, and removing that caused DSI
displays not to work.
This reverts the DSI parts of the commit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the cross dependencies between hwmod for automanaged device
information for OMAP and dts node definitions, we can run into scenarios
where the dts node is defined, however it's hwmod entry is yet to be
added. In these cases:
a) omap_device does not register a pm_domain (since it cannot find
hwmod entry).
b) driver does not know about (a), does a pm_runtime_get_sync which
never fails
c) It then tries to do some operation on the device (such as read the
revision register (as part of probe) without clock or adequate OMAP
generic PM operation performed for enabling the module.
This causes a crash such as that reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=66441
When 'ti,hwmod' is provided in dt node, it is expected that the device
will not function without the OMAP's power automanagement. Hence, when
we hit a fail condition (due to hwmod entries not present or other
similar scenario), fail at pm_domain level due to lack of data, provide
enough information for it to be fixed, however, it allows for the driver
to take appropriate measures to prevent crash.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_a_v3.13-rc/20131209030611/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=mDB2
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
ARM: OMAP2+: hwmod code/data: fixes for v3.13-rc
Fix a few hwmod code problems involving recovery with bad data and bad
IP block OCP reset handling. Also, fix the hwmod data to enable IP
block OCP reset for the OMAP USBHOST devices on OMAP3+.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_a_v3.13-rc/20131209030611/
* tag 'for-v3.13-rc/hwmod-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
Signed-off-by: Kevin Hilman <khilman@linaro.org>
commit dc75925d(OMAP: hwmod: Fix the missing braces) introduced
missing braces, however, we just set return result if clk_get fail
and we populate the error pointer in clk pointer and pass it along to
clk_prepare. This is wrong. The intent seems to be retry remaining
clocks if they are available and warn the ones we cant find clks for.
With the current logic, we see the following crash:
omap_hwmod: l3_main: cannot clk_get interface_clk emac_ick
Unable to handle kernel NULL pointer dereference at virtual address 00000032
pgd = c0004000
[00000032] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc1-00044-gcc9fd5a-dirty #19
task: ce0c3440 ti: ce0c4000 task.ti: ce0c4000
PC is at __clk_prepare+0x10/0x74
LR is at clk_prepare+0x14/0x24
<snip>
[<c044d59c>] (__clk_prepare+0x10/0x74) from [<c044d9b0>] (clk_prepare+0x14/0x24)
[<c044d9b0>] (clk_prepare+0x14/0x24) from [<c077d8c4>] (_init+0x24c/0x3bc)
[<c077d8c4>] (_init+0x24c/0x3bc) from [<c0027328>] (omap_hwmod_for_each+0x34/0x5c)
[<c0027328>] (omap_hwmod_for_each+0x34/0x5c) from [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40)
[<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) from [<c0008928>] (do_one_initcall+0x38/0x168)
[<c0008928>] (do_one_initcall+0x38/0x168) from [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc)
[<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) from [<c0521064>] (kernel_init+0x8/0x110)
[<c0521064>] (kernel_init+0x8/0x110) from [<c000e568>] (ret_from_fork+0x14/0x2c)
Code: e92d4038 e2504000 01a05004 0a000005 (e5943034)
So, just warn and continue instead of proceeding and crashing, with
missing clock nodes/bad data, we will eventually fail, however we
should now have enough information to identify the culprit.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In _ocp_softreset(), after _set_softreset() + write_sysconfig(),
the hwmod's sysc_cache will always contain SOFTRESET bit set
so all further writes to sysconfig using this cache will initiate
a repeated SOFTRESET e.g. enable_sysc(). This is true for OMAP3 like
platforms that have RESET_DONE status in the SYSSTATUS register and
so the the SOFTRESET bit in SYSCONFIG is not automatically cleared.
It is not a problem for OMAP4 like platforms that indicate RESET
completion by clearing the SOFTRESET bit in the SYSCONFIG register.
This repeated SOFTRESET is undesired and was the root cause of
USB host issues on OMAP3 platforms when hwmod was allowed to do the
SOFTRESET for the USB Host module.
To fix this we clear the SOFTRESET bit and update the sysconfig
register + sysc_cache using write_sysconfig().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
[paul@pwsan.com: renamed _clr_softreset() to _clear_softreset()]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this, the USB devices are sometimes not detected on OMAP4 Panda
with u-boot v2013.10.
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Fixes: af88fa9aa7 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As the emac uses the system control module registers for
reset and interrupts, we need to pass those in the platform
data until we have a separate system control module driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As we currently need to support a mix of legacy platform data and
device tree intialized data, let's make sure things keep working
for the TWL GPIOs.
Mostly the issue is caused by the fact that DSS does not yet have
device tree bindings, so we need to rely on the TWL GPIO callback
for setting up things like LCD backlight for some boards.
As of_platform_populate() for the TWL GPIO is called by twl-core
after the I2C bus has been initialized, we cannot pass the auxdata
table from the board init code to twl-core like we used to with
just legacy platform data.
So let's use the omap_device bus hook to patch in the platform
data for TWL GPIO until we have sorted out the issues with the
TWL GPIOs and device tree bindings.
The other option was be to initialize twl core using legacy
platform data, which seems like a step backwards as we're moving
to device tree only initialization. And we really don't want to
add custom configuration functions to the TWL GPIO driver either
for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have some device tree properties where the ti,hwmod have multiple
values:
am33xx.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
am4372.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
dra7.dtsi: ti,hwmods = "l3_main_1", "l3_main_2";
omap3.dtsi: ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
omap3.dtsi: ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
omap4.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
omap5.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
That's not correct way of doing things in this case because these are
separate devices with their own address space, interrupts, SYSCONFIG
registers and can set their PM states independently.
So they should all be fixed up to be separate devices in the .dts files.
We also have the related data removed for at least omap4 in commit
3b9b10151c (ARM: OMAP4: hwmod data: Clean up the data file), so
that data is wrongly initialized as null data.
So we need to fix two bugs:
1. We are only checking the first entry of the ti,hwmods property
This means that we're only initializing the first hwmods entry
instead of the ones listed in the ti,hwmods property.
2. We are only checking the child nodes, not the nodes themselves
This means that anything listed at OCP level is currently just
ignored and unitialized and at least the omap4 case, with the
legacy data missing from the hwmod.
Fix both of the issues by using an index to the ti,hwmods property
and changing the hwmod lookup function to also check the current node
for ti,hwmods property instead of just the children.
While at it, let's also add some warnings for the bad data so it's
easier to fix.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Stephen Boyd:
* soc/sched_clock:
ARM: versatile: Switch to sched_clock_register()
ARM: orion: Switch to sched_clock_register()
ARM: OMAP: Switch to sched_clock_register()
ARM: iop: Switch to sched_clock_register()
ARM: u300: Switch to sched_clock_register()
ARM: sa1100: Switch to sched_clock_register()
ARM: pxa: Switch to sched_clock_register()
ARM: OMAP2+: Switch to sched_clock_register()
ARM: OMAP1: Switch to sched_clock_register()
ARM: msm: Switch to sched_clock_register()
ARM: mmp: Switch to sched_clock_register()
ARM: IXP4xx: Switch to sched_clock_register()
ARM: integrator: Switch to sched_clock_register()
ARM: imx: Switch to sched_clock_register()
ARM: davinci: Switch to sched_clock_register()
ARM: clps711x: Switch to sched_clock_register()
ARM: timer-sp: Switch to sched_clock_register()
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These now come from device tree except for DSS and DMA that
still uses hwmod to initialize. That will get fixed when we
DSS gets device tree bindings and we move completely to the
dmaengine API.
Cc: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to add trailing commas to structs]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now boot with device tree and appended DTB
with basic devices working. If people are still using
this board, patches are welcome to add more complete
support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The old 2420 based H4 is probably not used at all as 2420
was Nokia specific SoC. I have one, but I'm not using it because
of it's large size, and I doubt anybody else is using it either.
We do have minimal omap2420-h4.dts in place, so if anybody wants
more support on H4, patches are welcome.
So let's just remove it as that helps us making mach-omap2 to
be device tree only.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we can boot n8x with the appended device tree with:
$ ARCH=arm CROSS_COMPILE=/usr/bin/arm-linux-gnueabi- make omap2420-n800.dtb
$ cat arch/arm/boot/zImage arch/arm/boot/dts/omap2420-n800.dtb > /tmp/zImage
Note that you need at least the following enabled:
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_SINGLE=y
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to keep things working when booted with
device tree. Note that we still need to initialize most
things with platform data as the drivers are lacking
support for device tree.
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize some devices using a late_initcall and test for
the device tree based booting for some devices.
This way we can keep things working for legacy platform
devices when booted with device tree.
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to initialize the legacy devices when booted
with device tree.
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like some boards need to fill in the auxdata before
we call of_platform_populate(). Let's add support for
auxdata quirks like we already have for pdata quirks for
legacy drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Santosh Shilimkar<santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
If CONFIG_SOC_HAS_REALTIME_COUNTER is not selected for omap5
or dra7xx, we can get the following error:
arch/arm/mach-omap2/built-in.o: In function `omap4_secondary_init':
:(.text+0x7ab0): undefined reference to `set_cntfreq'
Fix the issue by not trying to initalize the realtime counter
unles CONFIG_SOC_HAS_REALTIME_COUNTER is selected.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 26273e02a0 (ARM: OMAP2+: Fix build for dra7xx without
omap4 and 5) attempted to fix randconfig found errors for
redefinition of omap44xx_prm_reconfigure_io_chain, but was
not enough.
We need to check for AM43XX without any omap4 or 5 related
SoCs as well. And looks like we have prm44xx.o built always
anyways with omap-4-5-prcm-common because of the calls to
omap4_prm_vp_clear_txdone, so we can remove the duplicate
entries in the Makefile.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJShxvaAAoJEIwa5zzehBx3rz0P/R5I3+gENxHKXQaeRrgNRtE0
wcrPNkNoVoIWZ8FzRg3l0qzCeF2WvFXnjS9uM4oT5IbYdCdfu6JNvVvvj6CjccE0
9JBF+cMUqhDhjlYYPb8u4NFDmiBAjE0kr0bDX7yg1ogDn/FKbr1Zxsu1I2cYkKpF
JKk2jzf1dnjnngJznVkX0GJy7INsloul9jBQxiHLFHy2dB9qRovW2uIfCdkJ0QjL
2h0hwKjSdbRX8Q4jQs0mCCTNblbYFVSHgYP+FpE0BJFfNwPIItTTKGDYRu0I+pBG
gzLMS8UWVQO4vykpXwUkkD+YfgK/1woMGpAay1rI86GIvYOEXITSsoWsNhbmJ9gp
I4zvWETz11C9HpVQACuXIc3+5mgiHfKQdy4gp52vMUjoTOGLKSZNHWQICgxOEe0U
qN/kXVlhA1eYkdViXfVQyCpmr3TbIgjeYmXLIlptEYyFN1W7s8L0qOSRZeBkIo66
U+PlqjABySZZ24532eF6Dp8DLmB4jp3r0I1U17nYj5N9vTgeoyQk0x63zza5vt+Q
n+7talaazQbFGe151g7pKFrUezPeWYZYNd5CC/wUce/VSH+XgcSlzGFkw/DPuARM
QFtTAFTaFODt7zofQcd6L2lMIIRlRoU1aUgrb7c9YZlLl59b4BkEhD1dcc02X7pm
Ie7rtjvHT8isVRcIWZ16
=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Commit f2bf0e72d0 (ARM: OMAP2+: Add minimal 8250 support
for GPMC) added support for using bootloader timings for some
devices. Turns out we can do the same by looking at the compatible
flags of the child without adding a new function as smc91x has
a similar issue as 8250 with the bootloader timings.
And let's fix the 8250 naming, we should use the device type as
the name like uart instead of 8250 for zoom dts file.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get errors like:
arch/arm/mach-omap2/prm44xx.c:274: error: redefinition of ‘omap44xx_prm_reconfigure_io_chain’
arch/arm/mach-omap2/built-in.o: In function `default_finish_suspend':
arch/arm/mach-omap2/omap-mpuss-lowpower.c:95: undefined reference to `omap_do_wfi'
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP device hooks around suspend|resume_noirq ensures that hwmod
devices are forced to idle using omap_device_idle/enable as part of
the last stage of suspend activity.
For a device such as i2c who uses autosuspend, it is possible to enter
the suspend path with dev->power.runtime_status = RPM_ACTIVE.
As part of the suspend flow, the generic runtime logic would increment
it's dev->power.disable_depth to 1. This should prevent further
pm_runtime_get_sync from succeeding once the runtime_status has been
set to RPM_SUSPENDED.
Now, as part of the suspend_noirq handler in omap_device, we force the
following: if the device status is !suspended, we force the device
to idle using omap_device_idle (clocks are cut etc..). This ensures
that from a hardware perspective, the device is "suspended". However,
runtime_status is left to be active.
*if* an operation is attempted after this point to
pm_runtime_get_sync, runtime framework depends on runtime_status to
indicate accurately the device status, and since it sees it to be
ACTIVE, it assumes the module is functional and returns a non-error
value. As a result the user will see pm_runtime_get succeed, however a
register access will crash due to the lack of clocks.
To prevent this from happening, we should ensure that runtime_status
exactly indicates the device status. As a result of this change
any further calls to pm_runtime_get* would return -EACCES (since
disable_depth is 1). On resume, we restore the clocks and runtime
status exactly as we suspended with. These operations are not expected
to fail as we update the states after the core runtime framework has
suspended itself and restore before the core runtime framework has
resumed.
Cc: stable@vger.kernel.org # v3.4+
Reported-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function get_cpu_device() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function platform_device_register_resndata()
returns ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull LED subsystem changes from Bryan Wu:
"LED subsystem updates for 3.13 are basically cleanup and also add a
new driver for PCA9685"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp55xx: handle enable pin in driver
leds-gpio: of: led should not be created if its status is disabled
of: introduce of_get_available_child_count
leds: Added driver for the NXP PCA9685 I2C chip
leds: pwm: Remove redundant of_match_ptr
leds: Include linux/of.h header
leds: dac124s085: Remove redundant spi_set_drvdata
leds: lp55xx: enable setting default trigger
leds: blinkm: Remove redundant break
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Board-related updates. This branch is getting smaller and smaller, which is
the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates for OMAP
and a bit of new board support for Rockchip boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZYOa
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board-related updates. This branch is getting smaller and smaller,
which is the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates
for OMAP and a bit of new board support for Rockchip boards"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
ARM: tegra: defconfig updates
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
ARM: shmobile: marzen: enable INTC IRQ
ARM: shmobile: bockw: add SMSC support on reference
ARM: shmobile: Use SMP on Koelsch
ARM: shmobile: Remove KZM9D reference DTS
ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
ARM: shmobile: Remove non-multiplatform KZM9D reference support
ARM: shmobile: Use KZM9D without reference for multiplatform
ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBqdAAoJEIwa5zzehBx3cIEP/0L8ayPZV/fFpF3VheP7nyq9
nanUc74GVHu71rhiACsfqsP9QGQT6Ye+RNvD8gVcmmqW+7TjWG19nwgjO+GbJmIF
Sr5jNaSLy2yeMHd6aEOTYtpQ/kUdFePvEVMVJG4nx8vVa0sxk7YCIsHFNQTV4Wgv
FOnJ2jx3RvM6ing5SfmglB3ai7dwYxKKCZvzLqzn2vs0W+Fw0jXv/OEjbdd+WAfK
K94lFIqQXcxyDeF2NTVtlFT/F+LKbiRP88kM2ZkJkz5RHcSXgJNmJmVDCHwGxH08
ri9QOX6stHT6gNFl/B5ckpzg5PbuzkEnlg1GXWn7fnx7OoBKekx8SKoP0+sjkpxF
kX5pfERdBHUju1mfHDkxfdPAQ4RFDVcYDwNoTC1zBhDSfMuFsTGGNdeR0dhGQnmA
Vzc8RfIRzFhGEuXDktz7cZIpOuq7OI62jt6qDLqWSWSOa9ZfqsOMdCcA3QTV3rTi
nHiOQBTM0Bl78SrXzE0PmcD4obCnBvJqthSF5Z09N/POBtz8i4GsF7k4S1rr/rvX
HA/wp9Lzt4hvCoj1gwEGLqUnSiey1b7a3rqn03mNQvX7NW9StIg1VCauQZBR1KwP
Xtxgt48QgjQ7wzh4RGs2FdAgW4cw9nEbUTVRBLkQ7jxW+zh5CRJlS5dprBMR7Ier
7necO/DWPLnhaSAj4eXB
=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
A set of fixes for various platforms that weren't considered bad enough
to include in 3.12 (nor -stable). Mostly simple typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=70+h
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"A set of fixes for various platforms that weren't considered bad
enough to include in 3.12 (nor -stable). Mostly simple typo fixes,
etc"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: irq, AM33XX add missing register check
ARM: OMAP2+: wakeupgen: AM43x adaptation
ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
ARM: rockchip: remove obsolete rockchip,config properties
ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
ARM: OMAP1: fix incorrect placement of __initdata tag
ARM: OMAP: remove deprecated IRQF_DISABLED
ARM: OMAP2+: throw the die id into the entropy pool
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves the handling of the chip's enable pin from the board
code into the driver. It also updates all board-code files using the
driver to incorporate this change.
This is needed for device tree support of the enable pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSZRSSAAoJEIaOsuA1yqRE6EAP/AuF0dWV3wNSuv5h3ZPOybu8
uULX0E/VA2aGs8/55FeuQIJAn499zdt0KH5l8P3CGrKBPk8BN/rD55a6uwYEfWO8
wwTJpVeRyRQS8jes22vPqA22TXgl88SJO0RrsCarrzOcMNloVtOA4zyorITuGZQB
jEKmf9BdjIUlzZkH9t33v3O8kB5pJ1YvBQGRWXbBZvxSzohPC2LYerZKMPN99hDB
2YnJXVKZqZzKbcQQmJklWqRo0RTprWz0Mqcu2r8Lnnn2ZqnT3RBmCBsYXefsp4nF
egRJy51DiypEYt3/OEBf21BySjZHjO6+9jfzOmuOGoEiqw6XCRFMydVpqJJHC8WX
MoCs31VnGwwwBpSOz9ECS9QYXne9jx/bJ6iKoS736sgA20ZA6wBbEDhJlTckcZtm
TEC+UTKevNACAP8cjhGEquqwt5H/rMaYFMXEYQj+gvO2jDsNUGWb74l5VDaBiIm7
GzdUmgmYym8HKT80tgEcgvsUoUphDeNE84OW/jo1nFUDvCniLfQBAYZooEnTHY2H
AW+DqimJzNnKcHo4w/HUQhRgK9147aRbskmVIbepIIW7WQdFQBOPVy7BbfnVD2vA
j01JPshgtnjb+MZb6VqnbcaWKPnJr3KTnOpTTMyk5pKnBOf6PHb1S1Tq5uqtW2Ki
gqi/SXZJ1bYDVaaspNWr
=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
dpll4_m3_ck and dpll4_m4_ck have divider bit fields which are 6 bits
wide. However, only values from 1 to 32 are allowed. This means we have
to add a divider tables and list the dividers explicitly.
I believe the same issue is there for other dpll4_mx_ck clocks, but as
I'm not familiar with them, I didn't touch them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss1_alwon_fck_3430es2,
dss1_alwon_fck_3430es1 and dpll4_m4x2_ck so that the DSS's fclk can be
configured without the need to get the parent's parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss_dss_clk so that the DSS's fclk can
be configured without the need to get the parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With OMAP3+ and AM33xx supported SoC having defined CPU device tree
entries with operating-points and clock nodes defined, we can now use
the SoC generic cpufreq-cpu0 driver by registering appropriate device.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x, AM43xx, OMAP5 and DRA7 have missing late init hook. Introduce
SoC specific hook with a call to OMAP2+ generic lateinit hook. This
allows the generic late initializations such as cpufreq hooks to be
active.
Based on out-of-tree patches that need to be introduced in
mainline, this introduction allows us to provide the foundation for
further SoC specific features as they are developed.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3+ supports both device tree and non-device tree boot.
Device tree bindings for OMAP3+ is supposed to be added via dts following:
Documentation/devicetree/bindings/power/opp.txt
Since we now have device tree entries for OMAP3+ cpu OPPs,
The current code wrongly adds duplicate OPPs. So, dont register OPPs
when booting using device tree.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am33xx has a INTC_PENDING_IRQ3 register that is not checked for pending
interrupts. This patch adds AM33XX to the ifdef of SOCs that have to
check this register.
Cc: stable@vger.kernel.org
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43x has 224 interrupts and 7 banks, make it as maximum values. Keep
default values as earlier, if am43x is detected, update interrupts and
banks accordingly.
Also AM43x has only one cpu, ensure that clearing bitmask at wakeupgen
is done only for the single existing cpu, existing code assumes that
there are two cpu's.
If bitmask is cleared in wakeupgen for the nonexistent second cpu,
an imprecise abort happens as soon as Kernel switches to user space.
It was rootcaused by Sekhar Nori <nsekhar@ti.com>.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP3 PM code for off-mode currently saves the scratchpad contents for CM
registers within OMAP control module driver. However, as we are separating
CM code into its own driver, this must be moved also. This patch adds a
new API for saving the CM scratchpad contents and uses this from the high
level scratchpad save function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McBSP driver require special hacks to enable/disable the autoidle feature
for its interface clock for the proper function of the sidetone hardware.
Currently the driver just writes CM registers directly, which should be
avoided. Thus, changed the driver to use the new deny/allow_autoidle
clock API calls.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some drivers require direct access to the autoidle functionality of the
interface clocks. Added clock APIs for these, so that the drivers do not
need to access CM registers directly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Users of the CM funtionality should not access the CM registers directly
by themselves. Thus, added new CM driver APIs for the OMAP2 specific
functionalities which support the existing direct register accesses, and
changed the platform code to use these. This is done in preparation
for moving the CM code into its own individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Device Tree support for IGEP boards in mainline is almost
finished. The only remaining bits are support for the
Marvell SD8686 wifi + BT and TFP410 DVI chips.
Adding support for these should be straightforward so let's
not block OMAP3 moving to Device Tree only boot and remove
the board file for IGEP boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now have pretty decent device tree based support for
zoom platforms. It's not complete, but basics work for
me so adding more features should be quite trivial.
Looks like also 3630 sdp is zoom based, and looking
at it's board file should also be trivial to support
with the device tree based booting.
Patches are welcome if people are still using these.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now have pretty decent support with the device tree
based booting. Patches to add more features are welcome.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Delete board file for Nokia RM-680/RM-696 (N950/N9). DT-based booting
should be used for further development on this HW.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will be the last new set of hwmod data for any SoC
as future SoCs will use a driver and device tree based
approach. But before that can be dealt with, we need to
first sort out the pending driver/clk issues.
Queued by Paul Walmsley <paul@pwsan.com>:
Add hwmod and PRCM data for the TI AM43xx family of SoCs.
Under normal circumstances, these patches would not be merged.
The hwmod and PRCM data should be moved out either to DT data or
to drivers/. Also, the current implementation trades off lines
of diff by dynamically rewriting static data at runtime, which is
a bad practice - it causes future maintenance headaches.
However, after speaking with my upstream, it sounds like it's
better to merge these patches in their current state, due to long
term considerations.
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/am43xx_support_v3.13/20131015213706/
Due to the lack of an AM43xx board and any available public
documentation, it's impossible for me to review or test that
platform in any meaningful way. But at least the tests above
verify that the patches don't affect existing platforms -
particularly AM33xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=amRz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/am43xx-hwmod-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Changes needed for am43xx for the hwmod data.
This will be the last new set of hwmod data for any SoC
as future SoCs will use a driver and device tree based
approach. But before that can be dealt with, we need to
first sort out the pending driver/clk issues.
Queued by Paul Walmsley <paul@pwsan.com>:
Add hwmod and PRCM data for the TI AM43xx family of SoCs.
Under normal circumstances, these patches would not be merged.
The hwmod and PRCM data should be moved out either to DT data or
to drivers/. Also, the current implementation trades off lines
of diff by dynamically rewriting static data at runtime, which is
a bad practice - it causes future maintenance headaches.
However, after speaking with my upstream, it sounds like it's
better to merge these patches in their current state, due to long
term considerations.
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/am43xx_support_v3.13/20131015213706/
Due to the lack of an AM43xx board and any available public
documentation, it's impossible for me to review or test that
platform in any meaningful way. But at least the tests above
verify that the patches don't affect existing platforms -
particularly AM33xx.
* tag 'omap-for-v3.13/am43xx-hwmod-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: hwmod: Add qspi data for am437x.
ARM: OMAP2+: hwmod: Add USB hwmod data for AM437x.
ARM: OMAP2+: AM43x PRCM init
ARM: OMAP2+: AM43x: PRCM kbuild
ARM: OMAP2+: hwmod: AM43x operations
ARM: OMAP2+: hwmod: AM43x support
ARM: OMAP2+: CM: AM43x clockdomain data
ARM: OMAP2+: PM: AM43x powerdomain data
ARM: OMAP2+: PRCM: AM43x definitions
ARM: OMAP2+: hwmod: AM335x: remove static register offs
ARM: OMAP2+: hwmod: AM335x: runtime register update
ARM: OMAP2+: hwmod: AM335x/AM43x: move common data
ARM: OMAP2+: CM: cm_inst offset s16->u16
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Under normal circumstances, these patches would not be merged.
The hwmod and PRCM data should be moved out either to DT data or
to drivers/. Also, the current implementation trades off lines
of diff by dynamically rewriting static data at runtime, which is
a bad practice - it causes future maintenance headaches.
However, after speaking with my upstream, it sounds like it's
better to merge these patches in their current state, due to long
term considerations.
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/am43xx_support_v3.13/20131015213706/
Due to the lack of an AM43xx board and any available public
documentation, it's impossible for me to review or test that
platform in any meaningful way. But at least the tests above
verify that the patches don't affect existing platforms -
particularly AM33xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=PrDf
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13/am43xx-support' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.13/hwmod
Add hwmod and PRCM data for the TI AM43xx family of SoCs.
Under normal circumstances, these patches would not be merged.
The hwmod and PRCM data should be moved out either to DT data or
to drivers/. Also, the current implementation trades off lines
of diff by dynamically rewriting static data at runtime, which is
a bad practice - it causes future maintenance headaches.
However, after speaking with my upstream, it sounds like it's
better to merge these patches in their current state, due to long
term considerations.
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/am43xx_support_v3.13/20131015213706/
Due to the lack of an AM43xx board and any available public
documentation, it's impossible for me to review or test that
platform in any meaningful way. But at least the tests above
verify that the patches don't affect existing platforms -
particularly AM33xx.
counter on newer omaps, and to fail early for omap5 es1.0
SoCs that don't have any support merged for them in the
mainline tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSWJfdAAoJEBvUPslcq6VzViYQAIz0P4wVnmEexEAFfT6VDuX5
eJP1gvtjjjiSpFt6PIUhTzvUThZpx53Jir707cZ0nOKxvVjTpoVljQmw0b2JGuZX
Kgl6D044jU9aH0W9CQWif+SxiNLPD03pQ3hk1sPBGusIFpTp7mzqGvw8Q8WH/xAb
Hn3pEK8/FMsP0pD837BuvRR/JLqC06USz/1xVN5BJ845Eba1FOA1WSPKGW8AqRSc
d77U9CNdWGd/TskJ6tTOkxXhp4qQcyB8O4HP4QG0p/g5/1y8yEwK3wW5S8HQi4ae
v6nIwPiKl3MEj1GLAUp2pUiNYi2WguMLClZjNHTwRY2TU8BgoMpGwPx+7Uyv/WZQ
dD3VqdUYjPycdYy8/tQthndtAKjbaX5dlNjL8tRyM5Kv9EOoQdUSs3qg7PHtaqkP
V6/qPKaoBX8YkNNrCYZNB67TE6TAlZ753r2rp1WMW1GzeGXnQqqUbnPLfvAxxDku
FSxBppOqlk3WbM7ecoqDTm9CsaB0XQ/Ab2mI0slNKOgSrZfkqJ/UDTAtMwnspqxY
9HvQOnOrutuWdZFUz0noaElZe7Zjjg5v1dmUcIKKC3k9/ACFFOMMlRxyRw33s4tG
i7dkAn098X6n/RGyfzE985NLMW7mgj1u666XTTPg2+P5LU+5QU98qBPnojxw5mRn
6IW9qDLh/mghe+lmWQja
=GhHB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/soc-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
SoC related changes for omaps to support the realtime
counter on newer omaps, and to fail early for omap5 es1.0
SoCs that don't have any support merged for them in the
mainline tree.
* tag 'omap-for-v3.13/soc-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build error for realtime counter init if not enabled
ARM: OMAP5/DRA7: realtime_counter: Configure CNTFRQ register
ARM: OMAP5: id: Remove ES1.0 support
ARM: OMAP2+: DRA7: realtime_counter: Add ratio registers for 20MHZ sys-clk frequency
Signed-off-by: Kevin Hilman <khilman@linaro.org>
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
Add hwmod for USBSS and the OCP2SCP for AM437x.
AM437x has got 2 instances of USBSS.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Build AM43x power domain, clock domain and hwmod data.
Many of AM43x IP's and interconnects are similar as that in AM335x,
hence AM335x hwmod data is being reused with necessary changes.
Earlier the plan was to reuse AM335x specific PRCM code, but as AM43x
PRCM register layout is much similar to OMAP4/5, AM335x PRCM is
divorced and instead married with OMAP4/5 PRCM for AM43x.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reuse OMAP4 operations on AM43x.
Context related ops are not used on AM43x, as this would not add value
when using DT and AM43x is DT only boot. This additionally helps not to
add context register offset for each hwmod.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support for IP's that are present in AM43x, but not in AM335x.
AM43x additional ones added here are,
1. synctimer
2. timer8-11
3. ehrpwm3-5
4. spi2-4
5. gpio4-5
AM43x pruss interconnect which is different as compared to AM335x, has
been taken care.
And register offsets for same hwmod's shared with AM335x is different,
AM43x register offsets are updated appropriately.
ocp clock of those in l4_wkup is fed from "sys_clkin_ck" instead of
"dpll_core_m4_div2_ck", so "ocpif" for those in AM43x l4_wkup has been
added seperately.
hwmod's has been added for those that have main clock (wkup_m3, control,
gpio0) and clock domain (l4_hs) different from AM335x. debugss and
adc_tsc that have different clocks and clockdomains repectively has not
been added due to the reasons mentioned below.
AM43x also has IP's like qspi, hdq1w, vpfe, des, rng, usb, dss, debugss,
adc_tsc. These are not handled here due to both/either of following
reasons,
1. To avoid churn; most of them don't have DT bindings, which would
necessitate adding address space in hwmod, which any way would have
to be removed once DT bindings happen with driver support.
2. patches would come in from sources other than the author
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe clock domains in AM43x SoC.
OMAP4 clockdomain operations is being reused here.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all power domains in AM43x SoC.
OMAP4 powerdomain operations is being reused here.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hwmod common to AM43x and AM335x has register offsets different. It is
now updated based on SoC detection at run time, hence remove statically
initialized ones.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most of IP's in AM335x is present on AM43x and so in those cases both
will use same hwmod database (except for a few cases where clock related
details differ), but there is difference w.r.t register offset between
these. Update register offsets at runtime based on the SoC detected to
help in sharing otherwise same hwmod.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM335x and AM43x have most of the IP's and interconnect's similar.
Instead of adding redundant hwmod data, move interconnects and hwmod
similar between AM335x and AM43x to a common location. This helps in
reuse on AM43x.
AM335x interconnects that has difference and not present in AM43x are
not moved. ocp clock of those in l4_wkup is fed from a different source
for AM43x. Also pruss interconnect is different.
AM335x hwmod's that has difference other than prcm register offsets
(difference is in clocks of wkup_m3, control, gpio0, debugss and clock
domain of l4_hs, adc_tsc as compared to AM43x) and those that are not
present in AM43x are not moved.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most of the AM43x CM reg address offsets are with MSB bit '1' (on
16-bit value) leading to arithmetic miscalculations while calculating
CLOCK ENABLE register's address because cm_inst field was a type of
"const s16", so make it "const u16".
Also modify relevant functions so as to take care of the above.
[afzal@ti.com: fixup and cleanup]
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Otherwise we can get an error with some configs:
arch/arm/mach-omap2/timer.c:73: undefined reference to `omap_smc1'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add this hwmod data to allow USB3 to work in OMAP5 boards.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated to apply against Paul's changes]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just initialize things using the bootloader timings like
we've been doing for the legacy booting too. It should be
possible to patch in the GPMC timings for the based on the
TL16CP743C/TL16C754C manual at:
http://www.ti.com/lit/ds/slls644g/slls644g.pdf
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the wl12xx bindings are still pending, this way we can
get things working for omap3 evm and zoom platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For few things we're still going to be needing platform
data for device tree based drivers. Let's set up auxdata
handling and do it in pdata-quirks.c so we have all the
legacy calls in one place.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The realtime counter called master counter, produces the count
used by the private timer peripherals in the MPU_CLUSTER. The
CNTFRQ per cpu register is used to denote the frequency of the counter.
Currently the frequency value is passed from the
DT file, but this is not scalable when we have other non-DT guest
OS. This register must be set to the right value by the
secure rom code. Setting this register helps in propagating the right
frequency value across OSes.
More discussions and the reason for adding this in a non-DT
way can be seen from below.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg93832.html
So configuring this secure register for all the cpus here.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that display information and setup is made from dss-common
there is no need to have this code in the board file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEPv2 board has both an DVI and TFP410 video interfaces but
DSS support for DeviceTree has not yet landed in mainline so
is necessary to init the displays using legacy platform code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have DT bindings to specify which devices should not
be reset and idled during init, make hwmod extract the information
(and store them in internal flags) from Device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For modules/IPs/hwmods which do not have
-1- sys->class->reset()
and
-2- hardreset lines
and
-3- No way to do an ocp reset (no sysc control)
the flag 'HWMOD_INIT_NO_RESET' is not much useful.
Cleanup all such instances across various hwmod data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the missing sysc configuration to the AM335 spinlock hwmod
data. This ensures that smart-idle is enabled whenever the module
is enabled by the driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak