Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the Silk board support to include U14 which is an I2C based EEPROM
hooked up to the I2C1 bus.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the on-board voltage regulator hooked up to GPIO3_20
on r8a7779 Marzen. The board schematics describes the regulator as U4
TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20
while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the
pull-ups for the data pins of SDHI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Stout base board support making use of 1 GiB of memory,
the Renesas H2 r8a7790 SoC with the SCIFA0 serial port
and CA15 with ARM architected timer.
Furthermore, this device tree contains entries for:
- 4x LEDs
- SDHI SD/MMC controller
- Display unit with HDMI output
- SH fast ethernet controller
- QSPI controller with S25FL512S attached to it
- I2C controller with DA9210 and DA 9063 PMICs
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
cec-clock is a fixed clock generator that is not controlled by i2c-12
and thus should not be a child of the i2c-12 bus node. Rather, it should
be a child of the root node of the DT.
Fixes: c5aa879776 ("ARM: dts: lager: Add CEC clock for HDMI transmitter")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DTC now warns about missing #sound-dai-cells:
/sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in
node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle
(referred from sound-dai[0])
Pass the required '#sound-dai-cells' property to fix it.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the standard 'stdout-path' property to fix the following DTC warnings:
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dtb: Warning
(chosen_node_stdout_path): /chosen:linux,stdout-path: Use
'stdout-path' instead
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now gives the following warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/stih407-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/stih410-b2260.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add i.MX 6SoloLiteLite (i.MX6SLL) SoC support on top of the existing
i.MX6SL platform code.
- Improve the SoC revision mapping by utilizing the MAJOR field of
ANATOP DIGPROG register.
- Add CPUIDLE_FLAG_TIMER_STOP flag for cpuidle ARM power off state,
so that we can use ARM generic timer for some i.MX6 SoC.
- Set low-power interrupt mask for i.MX25 to support STOP mode.
- Drop EPIT driver as there is no user of it.
- Simplify the error path of imx6_pm_get_base() a bit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaqidWAAoJEFBXWFqHsHzO5OgIALasN3eUJ8TmVJOChBBC4lCc
20e9B0dqrnKfh3rXfPKl2LiG7SWid288V1T9X4K54PScgSaWFvV8zAwabchXP1Ev
cl2yUzOT7YZlcRFw8EYJufEPS41KgTrF84Vkm6hDYeEErKDu9tw/L8qyhMPm6421
jkHvfU4kVVtJ+k9szwId7ua7nw021l9KtI1G1qdQZ3e/Kkagg3/MemVKiAERsou3
J11hUc5rG5+1/5pgU7HTwN2q3Q6JbBvhF2MHfVEuAP0GUVBk2hFAD4mxczcvSOjW
KyQJQaQ4qEbpiJqdaHhBjA2XDSASo8S/y/92AdMRs+4+U9g0BbB+LaPyD4DVt6Y=
=YDxX
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Pull "i.MX SoC changes for 4.17" from Shawn Guo:
- Add i.MX 6SoloLiteLite (i.MX6SLL) SoC support on top of the existing
i.MX6SL platform code.
- Improve the SoC revision mapping by utilizing the MAJOR field of
ANATOP DIGPROG register.
- Add CPUIDLE_FLAG_TIMER_STOP flag for cpuidle ARM power off state,
so that we can use ARM generic timer for some i.MX6 SoC.
- Set low-power interrupt mask for i.MX25 to support STOP mode.
- Drop EPIT driver as there is no user of it.
- Simplify the error path of imx6_pm_get_base() a bit.
* tag 'imx-soc-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Add basic msl support for imx6sll
ARM: imx: pm-imx6: Return the error directly
ARM: imx: avic: set low-power interrupt mask for imx25
ARM: imx: Improve the soc revision calculation flow
ARM: imx: add timer stop flag to ARM power off state
ARM: imx: Remove epit support
This patchs adds the minimal defconfig for the OXNAS ARMv6 SoCs
including the OX820 SoC and needed minimal configurations.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Updates to OpenPower BMC systems:
A number of updates to use recently merged drivers, including moving to
upstreamed IPMI BT nodes, a temp sensor for Romulus, and adding
simple-reset for UARTs.
This includes more of Palmetto's device tree, so that it's ever so
close to booting the host with an upstream kernel.
New machines:
Add Qualcomm Centriq ARM64 server reference platform, which will run
OpenBMC on an AST2500.
-----BEGIN PGP SIGNATURE-----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=7HDC
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.17-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "ASPEED device tree updates for 4.17" from Joel Stanley:
Updates to OpenPower BMC systems:
A number of updates to use recently merged drivers, including moving to
upstreamed IPMI BT nodes, a temp sensor for Romulus, and adding
simple-reset for UARTs.
This includes more of Palmetto's device tree, so that it's ever so
close to booting the host with an upstream kernel.
New machines:
Add Qualcomm Centriq ARM64 server reference platform, which will run
OpenBMC on an AST2500.
* tag 'aspeed-4.17-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add Qualcomm Centriq 2400 REP BMC
ARM: dts: aspeed: romulus: Add w83773g temp sensor
ARM: dts: aspeed: romulus: hog GPIOS7
ARM: dts: romulus: Remove MAX31785 device
ARM: dts: palmetto: Request mux as per strapping configuration
ARM: dts: palmetto: Enable rear UART
ARM: dts: aspeed: Add LPC reset controller node
ARM: dts: aspeed: Add Palmetto GPIO hogs
ARM: dts: palmetto: Add LEDs and GPIO keys
ARM: dts: aspeed: Add LPC clock phandles
ARM: dts: aspeed-g5: Update LPC node
ARM: dts: aspeed: Enable IPMI BT node on OpenPower machines
ARM: dts: aspeed: Add IPMI BT node
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier AIO audio system needs I2S data in/out lines
and clock signal pins to connect external codec chip.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The compatible string was mistakenly pulled from the downstream tree and the
startup delay property is needed to prevent io errors on initial page select.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The #sound-dai-cells property may be required to reference the CPU DAI
properly. This change is required for Snow HDMI audio.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As serial interface is already specified into stdout-path property,
"console=ttyASN,115200" from bootargs can be removed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update serial aliases from "ttyASN" to more common "serialN".
Since dtc v1.4.6-9-gaadd0b65c987, aliases property name must
be lowercase only. This allows to fix following dtc warnings:
arch/arm/boot/dts/stih418-b2199.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih407-b2120.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih410-b2260.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih410-b2120.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VCHIQ firmware communication channel operates in parallel with our
other mailbox-based channel. This is the communication channel that
exposes the firmware's media decode/encode and ISP interfaces.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com> (v2)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Booting a crash kernel while in an interrupt handler is likely
to leave the Active Priority Registers with some state that
is not relevant to the new kernel, and is likely to lead
to erratic behaviours such as interrupts not firing as their
priority is already active.
As a sanity measure, wipe the APRs clean on startup. We make
sure to wipe both group 0 and 1 registers in order to avoid
any surprise.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we removed the inclusion of skeleton.dtsi from the device trees, we
broke booting for systems with bootloaders that aren't device tre aware.
This can be seen, for example, when appending the device tree blob to
the kernel image.
The reason booting broke was that the kernel lacked the device_type
label in the memory node. Add in a default memory node wth the
device_type. It can contain the memory address as the location is fixed
for each SoC generation, but the size needs to be added by the
bootloader or the board specific dts.
Fixes: 73102d6fdc ("ARM: dts: aspeed: Remove skeleton.dtsi")
Cc: <stable@vger.kernel.org>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Qualcomm Centriq 2400 REP (Reference Evaluation Platform) is
an aarch64 Armv8 server platform with an ast2520 BMC.
Signed-off-by: Ken Chen <chen.kenyy@inventec.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIOS7 shall be pulled low for CPLD to continue the power up sequence.
With this hogged as pull-low, the CPLD workaround can be removed in
OpenBMC.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Romulus uses ASPEED's fan tach instead of max31785:
* Pass1's max31785 is always reset by CPLD
* Pass2's max31785 is not connected
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
ARM-based SoC for 4.17, please pull the following:
- Tuomas enables the BCM2835 AUX driver which is necessary to provide
console on the Raspberry Pi 3
- Stefan turns on support for the BCM43438 Bluetooth adapter connected
via UART on the Raspberry Pi Zero Wireless and he also turns on
support for the thermal driver on the Pi 2 and 3.
-----BEGIN PGP SIGNATURE-----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=3aYj
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.17/defconfig' of https://github.com/Broadcom/stblinux into next/soc
Pull "Broadcom defconfig changes for 4.17" from Florian Fainelli:
This pull request contains multi_v7_defconfig changes for Broadcom
ARM-based SoC for 4.17, please pull the following:
- Tuomas enables the BCM2835 AUX driver which is necessary to provide
console on the Raspberry Pi 3
- Stefan turns on support for the BCM43438 Bluetooth adapter connected
via UART on the Raspberry Pi Zero Wireless and he also turns on
support for the thermal driver on the Pi 2 and 3.
* tag 'arm-soc/for-4.17/defconfig' of https://github.com/Broadcom/stblinux:
ARM: multi_v7_defconfig: Enable thermal driver for RPi 2/3
ARM: bcm2385_defconfig: Enable BT support for BCM43438
ARM: multi_v7_defconfig: Enable serial console on RPi 3
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJaqCvCAAoJEIfQlpxEBwcE7MIP/iMbvwen6G+JAk2yeeuOgZVi
+B2GLuOEcyi+MEQQgghpggjMehTPGTklXCNhNIziGYvpreGyzvGAmq/up+hFFVJ7
TNU0nslf8hBURdexx23/rkJBJFx8jv/R8au1PUZhEHLONQs38UBOe1umWbKDvpxn
qp+KvBF3EUdqVfnBcdagImr0MfVKlLpGjTuyfPfHhfs1R8egzY/fY/PUMBw4GFHB
alMrENKR3mFYl+cTk7Ox4yP9WYY4eZnrwuu43J0JHk6+r1De387MyWy+irNHKfKz
alux92DUDXMYxG57cEREfd9YzI0BOiU3orMBIkRACDpnI7bYWebviDKPda20dDli
4VgILTj1Vbi2/Qn+0PAWpqBZCVugnFNX44hfSZ1oVHjPlUVoDLojxcAG5AskmNVV
InMtROagSwgujK7PZD7knc4O73ihdoaLqp1dN0KLn+xx8x17wiVQUAWq2l5XpGD4
o+rarZRjAmIVe+xzvZfgmMRTaJRwmRNHgcWDWMKSACV63xmRxa9F9BM+Dep4zMq5
BON6Hvu9SMfgycgHWpU3GGKfAljRm8aRWzKRspIi+whqUuIhxCZcSyMlonrocv5b
O1AGm5f8Exdm9/4TTSzF7leVne0CXhIyfwEmtp42+y403OGONIaRqspe1on6nr7P
Yvdn0jO5CauPr7iM6Z10
=SKgx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs devicetree changes
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
* tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Switch to port 8 for CPU port
ARM: bcm2835: Add the DPI hardware to the device tree.
ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode
ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave
ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups
ARM: dts: bcm2837-rpi-3-b: add GPIO expander
ARM: dts: bcm2835: make the firmware node into a bus
ARM: dts: bcm283x: Fix probing of bcm2835-i2s
dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s
ARM: dts: bcm283x: Fix pin function of JTAG pins
This patch adds watchdog support by installing shmobile_boot_vector_gen2
to ICRAM1 when enough memory is available, in which case we also keep a
copy of MPIDR to complete the reset vector logic.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car Gen2 and RZ/G1 platforms, we use the SBAR registers to make non
boot CPUs run a routine designed to bring up SMP and deal with hot plug.
The value contained in the SBAR registers is not initialized by a WDT
triggered reset, which means that after a WDT triggered reset we jump
to the SMP bring up routine, preventing the system from executing the
bootrom code.
The purpose of this patch is to jump to the bootrom code in case of a
WDT triggered reset, and keep the SMP functionality untouched.
In order to tell if the code had been called due to the WDT overflowing
we are testing WOVF from register RWTCSRA.
The new function shmobile_boot_vector_gen2 isn't replacing
shmobile_boot_vector for backward compatibility reasons. The kernel
will install the best option (either shmobile_boot_vector or
shmobile_boot_vector_gen2) to ICRAM1 after parsing the device tree,
according to the amount of memory available.
Since shmobile_boot_vector has become bigger, "reg" property of nodes
compatible with "renesas,smp-sram" now need to be set to a value
greater or equal to "<0 0x60>".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: dropped #ifdef from common.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that we have added support for pre-pended Broadcom tags with commit
1160603960 ("net: dsa: b53: Support prepended Broadcom tags") we can
switch all the Northstar Plus reference boards to use port 8 for the CPU
port. This allows us to prepare room for supporting the Flow Accelerator
2 NAPT offload, and frees up port 5 to be made fully configurable for
the modes that it supports: internal, SGMII, RGMII etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's currently marked disabled, as it's not useful without a panel
associated with it and the GPIO pins routed to ALT2.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
"debounce-inteval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqj2kgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgaqOB/9y1t3gsyrUh2A6BwxS5MuHgO34YNsqm2n+
s8RDLit9Y/oAWU2G0CksTW6ksT8BboHV0xO12kC9HlUG/ia0ISm9XPXtbCc2KOae
wxc4tJ5BH2fz7NT1cfPEnVTkO3dA+0c3N9R9puOzrh796PVfRsjxYHtPWb2Qe3FT
Uz1JCA0/I9gSxFU/Mqte2ShtygSY6XznyWgqsRIzDgFbR9AWqyG+6fIdkcabE++O
uL1ucGaL3eLN8zgmZ6w20ZPAimkev6KbzA5VYtXgotSfXFcWJGEJzzeDpR2QAd0B
0Cua9ty/PiJLg121MO53iyGppRblB0yZAEnuBK9gQNGhT3u3o7t5
=sCTW
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix for a new dtc warning.
* tag 'v4.16-rockchip-dts32fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add missing #sound-dai-cells on rk3288
pins on OMAP-L138 Hawkboard.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/zSM
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "DaVinci fixes for v4.16" from Sekhar Nori:
A patch fixing GPIO look-up for MMC/SD card detect and write-protect
pins on OMAP-L138 Hawkboard.
* tag 'davinci-fixes-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix the GPIO lookup for omapl138-hawk
- Fix a copy-paste error in imx7d-sdb device tree, which results in two
usb-otg regulators are both named "regulator-usb-otg1-vbus" and
override each other.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaoiVxAAoJEFBXWFqHsHzOnu4H/Rx0n2o4jwFXeoQmwdGJoOkj
oo3LTjtAossU3ePuzgLhPooSaXXaCRDuTTIyiURFj8CmO2tkYuyjmwd0VI4QNPhC
I+dHUfpYgNpvpFd0gZDkGnYnptXf5sQ+lMdNhneqyOxwF8xQTwnMhwYvfkb1CIu/
3Q3vOTDes/K07+L9rTPihO0h8A3738WyR6PmTPP00sQTzYU+29pVKMYoS4u01c1A
PFcyfbY3Sggbd/NRexGpWyMPD6QQa7WUx3lwoTdOinT0XqQ9tG2TqZzQ5yhDrh24
sHzJVD0dWqJL717+IY7cEp4ma78JFGmO62C6nwWGfh4uJ/g4qmP7aAaDA5bfsDU=
=pBTN
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.16-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.16, 2nd round" from Shawn Guo:
- Fix a copy-paste error in imx7d-sdb device tree, which results in two
usb-otg regulators are both named "regulator-usb-otg1-vbus" and
override each other.
* tag 'imx-fixes-4.16-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-sdb: Fix regulator-usb-otg2-vbus node name
Now that all the grouping is done with RB trees, we no longer need
group_entry and can replace the whole thing with sibling_list.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Dmitri Prokhorov <Dmitry.Prohorov@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valery Cherepennikov <valery.cherepennikov@intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
-----BEGIN PGP SIGNATURE-----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=/vgG
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux into next/soc
Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
ARM: pxa: cm-x300: remove inline directive
ARM: pxa: fix static checker warning in pxa3xx-ulpi
MAINTAINERS: remove entry for deleted pxa3xx_nand driver
arm: dts: pxa: use reworked NAND controller driver
dt-bindings: mtd: remove pxa3xx NAND controller documentation
mtd: nand: remove useless fields from pxa3xx NAND platform data
mtd: nand: remove deprecated pxa3xx_nand driver
mtd: nand: use Marvell reworked NAND controller driver with all platforms
- Rename Atmel to Microhip in MAINTAINERS, Documentation and Kconfig
-----BEGIN PGP SIGNATURE-----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=oLw9
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.17-soc' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/soc
Pull "AT91 SoC for 4.17: from Alexandre Belloni:
- Rename Atmel to Microhip in MAINTAINERS, Documentation and Kconfig
* tag 'at91-ab-4.17-soc' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: Kconfig: Update company to Microchip
Documentation: at91: Update Microchip SoC documentation
MAINTAINERS: ARM: at91: update entry for ARM/Microchip
Add emif node for keystone2 devices, which is used for ECC support.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
[t-kristo@ti.com: made emif enabled by default for all keystone2 devices]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a watchdog node for keystone-k2g, with the corresponding clock and
power domain handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use 'atmel' as at24 manufacturer
- device addition and fixes for axentia boards
- fix sama5d4 pinctrl compatible
-----BEGIN PGP SIGNATURE-----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=8iJ8
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.17-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Pull "AT91 DT for 4.17" from Alexandre Belloni:
Not much this cycle, mainly changes on the Axentia boards from Peter and
a cleanup from Bartosz:
- use 'atmel' as at24 manufacturer
- device addition and fixes for axentia boards
- fix sama5d4 pinctrl compatible
* tag 'at91-ab-4.17-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9263ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91-sama5d2_ptc_ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9g20ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9260ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for sama5d34ek
ARM: dts: at91: sama5d4: fix pinctrl compatible string
ARM: dts: at91: tse850: make the sound dai cell count explicit
ARM: dts: at91: nattis: add lvds-encoder
ARM: dts: at91: nattis: use up-to-date mtd partitions
ARM: dts: at91: tse850: use the correct compatible for the eeprom
ARM: dts: at91: nattis: use the correct compatible for the eeprom
ARM: dts: at91: sam9rl: Properly assign copyright
Most of them are small fixes or cleanup.
Only the change on the clearfog will have a noticeable effect allowing
to use the i2c at an higher frequency.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWqK/8QAKCRALBhiOFHI7
1RRAAKCHV/9lXDrSQJlnmrQg0QkY8wZeggCeO7falJ3+WpWl03xKxcaqUQVNFIc=
=jSYw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.17-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.17 (part 1)" from Gregory CLEMENT:
Most of them are small fixes or cleanup.
Only the change on the clearfog will have a noticeable effect allowing
to use the i2c at an higher frequency.
* tag 'mvebu-dt-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: increase speed of i2c0 to 400kHz
arm: dts: kirkwood: fix error in #sound-dai-cells size
ARM: dts: kirkwood: Fix "debounce-interval" property misspelling
ARM: dts: armada: netgear-rn*: fix rtc node name
This adds information, that the battery is charged by the charger.
The Linux kernel uses this information to refresh battery information
when the power-supply changes.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org
Fixes: f4ff257cd1 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The A23/A33 reference tablet design has a DC barrel tied to the ACIN
of the PMIC. And being a tablet, it has a Li-Po battery.
Enable both power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A33-OLinuXino routes the SoC's headphone output to a headphone jack,
and the microphone input to a microphone jack. Power to the microphone
is provided by MBIAS.
This patch enables the various parts of the codec, and adds widgets and
routes for simple-card.
HBIAS is connected to the microphone jack as well, but in a manner that
is confusing and likely does not provide power. This part is left out
of this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A33-OLinuXino has a DC jack wired to the onboard PMIC's ACIN pins.
There is also a battery connector, wired to the PMIC's battery charger.
Enable the power supplies for both these components.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
None of the common regulators defined in sunxi-common-regulators.dtsi
are used for the A33-OLinuXino.
Drop the include.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Normal GPIO usage does not need an additional pinmix setting. Exclusive
usage of the pin will be guaranteed by the driver.
Drop the extra pinmux settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the i.MX25 reference manuals, each SSI has four FIFOs. All
of those FIFOs can store up to 15 entries.
The fsl_ssi driver's internal default for the FIFO depth in 8. Set our
non-default FIFO depth explicitly in the Device Tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98091" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can be also supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98090" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98095" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds missing clocks, clock-names properties so the CODEC can
properly handle its master clock. Without this change sound on exynos5250-snow
doesn't work.
Missing #sound-dai-cells property is also added so it is possible to specify
the DAI links properly for HDMI audio support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently the audio subsystem clocks are not configured properly on Snow
and sound is not working. The MAX98095 CODEC is not getting its master clock
on the MCLK pin connected to the SOC's CLKOUT GPIO. This patch adds CLKOUT
and other clocks configuration so HDMI audio can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This property is required for specifying link between the HDMI IP block
and the SoC's audio subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The multi-cluster SMP code maps the address spaces of several hardware
control blocks. The device nodes for them are SoC-specific. To help with
supporting other SoCs to re-use this code, these bits should be split
out to a separate function tied to the enable-method string.
This patch splits out and groups the device node lookup sequence, and
adds new data structures to have the newly created function tied to
the enable method string. This structure can also be used to encode
other differences between the SoCs.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Instead of having an early init function check the machine compatible
and installing multi-cluster SMP support for the A80 if it matches,
use a new cpu enable-method string. This makes the platform support
future proof in case anyone manages to add PSCI support.
The original init code for the SMP support is changed into the
.prepare_cpus callback in the smp_operations structure. Instead of
panicing when resources are missing like on some platforms, our code
merely guards against engaging SMP or CPU hotplug and returns an error.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The sunxi_mc_smp_lookback function is modeled after the mcpm_loopback
function in the MCPM framework. "lookback" was a typo introduced when
the new function was added.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Using the enable-method property for SMP support would allow future PSCI
implementations to override any in-OS support. This is better than just
matching against the machine compatible, and then having to determine
whether other methods are available or not.
This adds enable-method properties to all CPU nodes.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Buffalo WZR-900DHP has 8 LEDs, but there is not LED definitions in the
dts and cannot configure these LEDs.
I Added missing LED definitions for WZR-900DHP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The GPIO chip is called davinci_gpio.0 in legacy mode. Fix it, so that
mmc can correctly lookup the wp and cp gpios.
Note that it is the gpio-davinci driver that sets the gpiochip label to
davinci_gpio.0.
Fixes: c69f43fb4f ("ARM: davinci: hawk: use gpio descriptor for mmc pins")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a note on where the chip label is set]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add basic MSL support for i.MX6SLL.
The i.MX 6SoloLiteLite application processors are NXP's latest
additions to a growing family of multimedia-focused products
offering high-performance processing optimized for lowest power
consumption. The i.MX 6SoloLiteLite processors feature NXP's advanced
implementation of the ARM Cortex-A9 core, which can be interfaced
with LPDDR3 and LPDDR2 DRAM memory devices.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the PM8921 XOADC node to the PM8921 PMIC node,
defines the channels and further also define an IIO HWMON
node for the channels that are used for housekeeping of
voltages and die temperature for the PMIC chip die.
Tested on the Nexus 7 tablet:
lsiio
Device 000: PM8921-XOADC
cd /sys/bus/iio/devices/iio:device0
cat in_voltage10_input
616461 (0.625V reference voltage)
cat in_voltage11_input
(1.25V reference voltage)
cat temp1_input
35852 (die temperature)
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This DTS has support for the Samsung Galaxy S5 (codenamed klte).
Initial version have support just for serial console.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Daniele Debernardi <drebrez@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the copyright period and get rid of some spurious newlines.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Apalis TK1 module uses some dedicated GPIOs as I210 gigabit Ethernet
controller reset and to control RESET_MOCI aka reset module output
carrier input on MXM3 pin 26. The Apalis Evaluation Board furthermore
uses Apalis GPIO7 on MXM3 pin 15 as reset signal for its PLX PEX 8605
PCIe Switch.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module
explicitly configure it to high-impedance as well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Activate PWM pin muxing for Apalis PWM3. Note that the same PWM3 is
already active on pu6 being Apalis BKL1_PWM as well. Therefore exporting
that one for raw sysfs access will fail and one has to revert to using
the PWM backlight.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set "critical" trip temperatures for cpu, gpu, mem and pllx thermal
zones. These trips can trigger shut down or reset.
Similar to commit 40823f8e26 ("arm: tegra: set critical trips for
Tegra124").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt there is
no 'reg' property under stmpe_touchscreen, so remove it to fix the
following build warning with W=1:
arch/arm/boot/dts/tegra30-apalis-eval.dtb:
Warning (unit_address_vs_reg): Node
/i2c@7000d000/stmpe811@41/stmpe_touchscreen has a reg or ranges
property, but no unit name
Similar to commit 89277e8e26 ("ARM: dts: imx6qdl-apalis: Remove
unneeded reg property").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared to a
st,m41t00 this RTC has also an oscillator fail bit which allows to
detect when the RTC lost track of time.
Similar to commit c53bec16b1 ("ARM: dts: colibri/apalis: use correct
compatible for RTC") covering our NXP i.MX and Vybrid based modules.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a faster speed of 400 kbit/s for regular I2C busses.
Use a slower speed of 10 kbit/s for DDC/EDID to improve reliability.
Use a slower speed of 100 kbit/s for power I2C to be within specs of
the LM95245 temperature sensor.
While at it further annotate I2C pin usage.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove invalid uses of rsvd1 from Beaver device tree. Replace by actual
function names of pinmux option 1.
Taken from https://github.com/NVIDIA/tegra-pinmux-scripts commit
b0aceda108c0 ("remove invalid uses of rsvd1 from beaver config").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This switches a few interrupt definitions that were using either
GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW as IRQ type, which is invalid.
This is mostly a cosmetic change, that doesn't affect any driver.
Analogous to Paul's commit 38333641b6 ("ARM: tegra: nyan: Use proper
IRQ type definitions").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit f8f8f1d044 ("clk: Don't touch hardware when reparenting
during registration") ULPI has been broken on Tegra20 leading to the
following error message during boot:
[ 1.974698] ulpi_phy_power_on: ulpi write failed
[ 1.979384] tegra-ehci c5004000.usb: Failed to power on the phy
[ 1.985434] tegra-ehci: probe of c5004000.usb failed with error -110
Debugging through the changes and finally also consulting the TRM
revealed that rather than the CDEV2 clock off OSC requiring such pin
muxing actually the PLL_P_OUT4 clock is in use. It looks like so far it
just worked by chance of that one having been enabled which Stephen's
commit now changed when reparenting sclk away from pll_p_out4 leaving
that one disabled. Fix this by properly assigning the PLL_P_OUT4 clock
as the ULPI PHY clock.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the missing unit address for the VDE IRAM area node in accordance
with the mmio-sram device tree binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for the Video Decoder Engine found on Tegra30 SoC's.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
IRAM is a static RAM that consists of four contiguous 64 KiB blocks,
it is currently used to store CPU resume code, utilized by the video
decoder engine and could be used as a general-purpose fast memory.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the vf610m4 based boards include the real memory size in their
dts files, so remove the the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the vf500 based boards include the real memory size in their
dts files, so remove the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include memory node unit name in order to fix the following W=1
warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently CONFIG_SND_SOC_WM8962 is selected via SND_SOC_IMX_WM8962
machine driver option.
SND_SOC_IMX_WM8962 will be removed in the next kernel cycle, so
select the codec driver directly so that it can still be used
by default via the generic fsl-asoc-card machine driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two usb-otg regulators for imx7d-sdb are both called
"regulator-usb-otg1-vbus" and they effectively override each other.
This is most likely a copy-paste error.
Fixes: b877039aa1 ("ARM: dts: imx7d-sdb: Adjust the regulator nodes")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This add a DTS for the Digilent Zybo Z7 board.
This board is the successor board of Zybo, these are almost the same except
for ps-clk-frequency specifications.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu@cybertrust.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, 2x i2c, nor flash, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, i2c, nand uart, spi and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
and sd. But board is not supporting booting from sd card.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is fixing issue reported by dtc:
arch/arm/boot/dts/zynq-microzed.dtb: Warning (unit_address_vs_reg): Node
/memory has a reg or ranges property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prevents the error:
aspeed-smc 1e630000.spi: Error applying setting, reverse things back
The pinmux driver is only capable of modifying selected strapping bits
that make sense to change at runtime. The SPI strapping is not
currently defined modifiable, so "request" the mux as per how the board
is physically strapped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Palmetto BMC has a UART connected to a RS-232 transceiver designed
to be used as a serial console for the host processor. It appears as a
D-sub connector on the back of the chassis.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The NanoPi-M1-Plus have a 8GB eMMC, add a node for it.
This eMMC is always powered with 3.3V.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fixed "mmc2_8bits_pins" label typo; added subject prefixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the I2C clocks so the I2C busses can be used. The clock input is not
device specific (the AO I2C bus uses clk81 as input, while the two I2C
busses in CBUS have a separate "CLKID_I2C" gate, provided by the clock
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit 2b05f6ae1e ("ARM: ux500: remove PMU IRQ bouncer")
deleted some code to bounce and work around the weird PMU
IRQs in the DB8500 ASIC, but did a semantic mistake:
since the auxdata was now unused, the call to
of_platform_populate() was removed, but this does not
work: the default platform population will only kick in
if .init_machine() is assigned NULL, and since the U8540
was still using the callback that was not the case.
Fix this by reinstating the call to of_platform_populate(),
but pass NULL as auxdata.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: 2b05f6ae1e ("ARM: ux500: remove PMU IRQ bouncer")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
-----BEGIN PGP SIGNATURE-----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=WjCX
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.17" from Krzysztof Kozłowski:
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
* tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: exynos: Fix IOMMU support for GScaler devices on Exynos5250
ARM: dts: exynos: Remove unused bypass-smu property from Xyref5260
ARM: dts: exynos: Add missing interrupts property to PMIC on Trats board
ARM: dts: exynos: Fix unit addresses of PDMA nodes in Exynos5410
ARM: dts: exynos: Fix address of PPMU ACP on Exynos4210
ARM: dts: exynos: Cleanup power domain nodes in exynos3250.dtsi
ARM: dts: exynos: Add touchscreen node to Exynos4412 N710x
ARM: dts: exynos: Add Samsung's Exynos4412-based Midas boards
ARM: dts: exynos: Split Trats2 DTS in preparation for Midas boards
ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
dt-bindings: samsung: Document bindings for Midas family boards
ARM: dts: exynos: Add soc node to exynos4412
ARM: dts: exynos: Add soc node to exynos4210
ARM: dts: exynos: Add soc node to exynos4
ARM: dts: exynos: Add soc node to exynos5440
ARM: dts: exynos: Use pmu label in exynos4412
ARM: dts: exynos: Remove duplicated inclusion of syscon restart nodes on Exynos5410
ARM: dts: exynos: Use label instead of full path in exynos4412-itop-elite
ARM: dts: exynos: Use labels instead of full paths in exynos4412-trats2
ARM: dts: exynos: Use label instead of full path in exynos4412-odroid-common
...
As of commit 7f60830ab1 ("serial: sirf: Use generic
uart-has-rtscts DT property property"), the SiRF UART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "sirf,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=osrs
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.17, round 1" from Alexandre Torgue:
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
* tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: Fix sdio2 rcc hard coded value
dt-bindings: mfd: Add STM32F7 SDMMC2 rcc entry
ARM: dts: stm32: Enable sdio1 for stm32f769-disco
ARM: dts: stm32: Enable sdio1 for stm32f746-eval
ARM: dts: stm32: Enable sdio1 for stm32f746-disco
ARM: dts: stm32: Add sdio pins definition for stm32f7
ARM: dts: stm32: add SPI support on STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32h743i-eval
ARM: dts: stm32: add RTC support on STM32H743
ARM: dts: stm32: enable USB OTG HS on stm32h743i-eval
ARM: dts: stm32: add USB OTG HS and FS support for STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32f769-disco
ARM: dts: stm32: enable USB HS on stm32f769-disco
ARM: dts: stm32: select otg mode for usbotg_hs on stm32746g_eval
ARM: dts: stm32: add gadget fifo sizes to usbotg_hs on stm32f746
ARM: dts: stm32: Add push button to stm32f769 Discovery board
ARM: dts: stm32: Add push button to stm32f469 Discovery board
ARM: dts: stm32: Add leds support to stm32f769 Discovery board
ARM: dts: stm32: Add leds support to stm32f469 Discovery board
ARM: dts: stm32: Fix HSE clock frequency for stm32h743i-disco board
...
1. Add few remaining SPDX license identifiers.
2. Add cpuidle support to all Midas-based boards (including new
GT-I9300/GT-I9305/GT-N7100/GT-N7105).
-----BEGIN PGP SIGNATURE-----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=sUWr
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Pull "Samsung mach/soc changes for v4.17" from Krzysztof Kozłowski:
1. Add few remaining SPDX license identifiers.
2. Add cpuidle support to all Midas-based boards (including new
GT-I9300/GT-I9305/GT-N7100/GT-N7105).
* tag 'samsung-soc-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Extend cpuidle support to Midas boards
ARM: EXYNOS: Add SPDX license identifiers
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
-----BEGIN PGP SIGNATURE-----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=/hJY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Driver changes for ti-sysc for v4.17" from Tony Lindgren:
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
* tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable ti-sysc to use device tree data for smartreflex
PM / AVS: SmartReflex: Prepare to use device tree based probing
ARM: OMAP2+: Try to parse earlycon from parent too
ARM: OMAP2+: Add checks for device tree based sysconfig data
ARM: OMAP2+: Add functions to allocate module data from device tree
bus: ti-sysc: Handle some devices in omap_device compatible way
bus: ti-sysc: Add support for platform data callbacks
bus: ti-sysc: Remove unnecessary debugging statements
bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init
bus: ti-sysc: Handle stdout-path for debug console
bus: ti-sysc: Add suspend and resume handling
bus: ti-sysc: Add fck clock alias for children with notifier_block
ARM: OMAP2+: Prepare to pass auxdata for smartreflex
This series of changes from Dave Gerlach adds the PM related
code to allow low-power suspend states. The code consists of
the SoC specific assembly code and a related PM driver.
-----BEGIN PGP SIGNATURE-----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=hBzh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/am-pm-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Add am335x and am437x PM code for v4.17" from Tony Lindgren:
This series of changes from Dave Gerlach adds the PM related
code to allow low-power suspend states. The code consists of
the SoC specific assembly code and a related PM driver.
* tag 'omap-for-v4.17/am-pm-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: Add pm33xx driver for basic suspend support
ARM: OMAP2+: pm33xx-core: Add platform code needed for PM
ARM: OMAP2+: Introduce low-level suspend code for AM43XX
ARM: OMAP2+: Introduce low-level suspend code for AM33XX
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlqdd1IRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXNziQ/+OywQPRLgeYodIl5AXJCMaZhyFJPN1BP3
OXsDllCnqJOpH4yjIPz4WoEI3ciVRJw+iBOl28pDtomdyejyE9qx/FmIhL081Wgm
T7TgJTieungliRfZu3UWRJdinpEyEzvTtEWlSVWa++lH5Bsub7lIPJsZ3A2bYVMh
9n6uE9bzU/ECdq/1hP9fhM2rssf8mu5l1IKlYmPWuxoFm/YSYoiyneU+rOILnJQ6
dsbc71p3+VdsZBDI+nMGcLE923LGXKEmxlHoR9+9EY12MOIwbTt/jxcI8j+Iugfk
vetncsXbpKnbutTP1iXr64IXa5QFOZKtMNlfNqLo4aihWMJ6tV4570w/pxk/qMgq
+qCidWm9RgVUm1N4t8kMm8aWm1BC1L8g9fw2/l0JFBHcuIlOYewa6cZ6gcUI6XxN
BqcET9iyxG9HgqgB6yekHRI3niywgGcpw420RS0DLmxIzpnpeQHGkXrva0tVcVS7
4SZ9UWgLQVCKgm/8mSDv4PkIzuPXyu4fqjxzMihQdNUHAG1xeqODfU8SLsItW43a
sGojvPPNWhCyvL2hpWuyWsRSOTc8MyAteeowYN1PzoSCO0cI3MTL0TUpxRTBV/9/
y1l5DYmdc1HUARXxJWreBSl3uToADguqzYUv3rHe/B20+LA19F9GRzoc9uOhqTGn
ePjiA5EC64o=
=2B8N
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Move omap timer to drivers for 4.17" from Tony Lindgren:
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
* tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
clocksource: timer-ti-dm: Check prescaler value
clocksource: timer-ti-dm: Consolidate set source
clocksource: timer-ti-dm: Make unexported functions static
ARM: OMAP: pdata-quirks: Remove unused timer pdata
pwm: pwm-omap-dmtimer: Adapt driver to utilize dmtimer pdata ops
clocksource: timer-ti-dm: Hook device platform data if not already assigned
clocksource: timer-ti-dm: Populate the timer ops to the pdata
clocksource: timer-ti-dm: Add timer ops to the platform data structure
ARM: OMAP: Move dmtimer driver out of plat-omap to drivers under clocksource
clocksource: timer-ti-dm: Replace architecture
ARM: OMAP: Move dmtimer.h out of plat-omap
ARM: OMAP: timer: Wrap the inline functions under OMAP2PLUS define
ARM: OMAP: dmtimer: Remove all the exports
ARM: OMAP: Fix dmtimer init for omap1
This series is mostly a series from Suman Anna to remove now unused
platform data that is now coming from device tree. This also make it
a bit simpler to move the timer code to live under drivers in a
separate series of patches. There are also few minor clean-ups for
omap4 PM code.
-----BEGIN PGP SIGNATURE-----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=ivau
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/soc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "SoC changes for omaps for v4.17" from Tony Lindgren:
This series is mostly a series from Suman Anna to remove now unused
platform data that is now coming from device tree. This also make it
a bit simpler to move the timer code to live under drivers in a
separate series of patches. There are also few minor clean-ups for
omap4 PM code.
* tag 'omap-for-v4.17/soc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix typo for wakeup_ns_pa_addr
ARM: OMAP2+: Use v7_invalidate_l1 in omap4_finish_suspend
ARM: OMAP2+: Remove unused gpio header file references
ARM: OMAP: Move plat/i2c.h into mach-omap1 folder
ARM: OMAP2+: Cleanup omap_mcbsp_dev_attr and other legacy data
ARM: OMAP2+: Cleanup omap2_spi_dev_attr and other legacy data
ARM: OMAP2+: Cleanup omap_timer_capability_dev_attr usage
ARM: OMAP2+: Cleanup omap_i2c_dev_attr usage
ARM: OMAP2+: Cleanup omap_gpio_dev_attr usage
ARM: OMAP2+: Include types.h directly for hwmod data
Highlights:
----------
-Add STM32F769 MCU support
-Add STM32MP157 MPU support
-Add AMBA PL180 MMCI support for F4 and F7 MCUs
-Move STM32 documentation to rst format
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HDCw
-----END PGP SIGNATURE-----
Merge tag 'stm32-soc-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/soc
Pull "STM32 SOC updates for v4.17, round 1." from Alexandre Torgue:
Highlights:
----------
-Add STM32F769 MCU support
-Add STM32MP157 MPU support
-Add AMBA PL180 MMCI support for F4 and F7 MCUs
-Move STM32 documentation to rst format
* tag 'stm32-soc-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: stm32: restore reboot capabilities
ARM: stm32: Add AMBA support for STM32F4 and STM32F7 SoCs
ARM: stm32: add initial support for STM32MP157
ARM: stm32: prepare stm32 family to welcome armv7 architecture
Documentation: arm: stm32: move to rst format
ARM: stm32: Fix copyright
ARM: stm32: add new STM32F769 MCU
ARM: stm32: Kconfig: introduce MACH_STM32F769 flag
As SoCFPGA uses the standard suspend_valid_only_mem() for its
platform_suspend_ops.valid() callback, its platform_suspend_ops.enter()
callback will never be called with state equal to PM_SUSPEND_STANDBY.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
nspire_map_io() just calls debug_ll_io_init().
If machine_desc.map_io is not set, devicemaps_init() in the
common ARM code will call debug_ll_io_init(), so nspire_map_io() and the
initialization of .map_io can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
-----BEGIN PGP SIGNATURE-----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=UfHC
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for dra7 sdhci for v4.17" from Tony Lindgren:
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
* tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Correct evm_sd regulator max voltage
ARM: dts: dra76-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: am57xx-idk: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Remove mmc specific pinmux
ARM: dts: am57xx-beagle-x15: Add "vqmmc-supply" property for mmc2
ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes
ARM: dts: dra76-evm: Shift to using common IOdelay data
ARM: dts: dra76x: Create a common file with MMC/SD IOdelay data
ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
Reorder the mach-* inclusions so the comment about them being ordered
alphabetically ends up being true.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable SYSCON_REBOOT_MODE needed for Lego EV3 and build the DaVinci
watchdog driver in so reboot works even when modules are not loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+lpS
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.17/defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Pull "DaVinci defconfig updates for v4.17" from Sekhar Nori:
Enable SYSCON_REBOOT_MODE needed for Lego EV3 and build the DaVinci
watchdog driver in so reboot works even when modules are not loaded.
* tag 'davinci-for-v4.17/defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: set CONFIG_DAVINCI_WATCHDOG=y
ARM: davinci_all_defconfig: enable SYSCON_REBOOT_MODE
* rationalization of con_id names for phy clocks to make DT conversion easy
* A patch to move away from syscon as platform device. This is needed for
common clock framework conversion as well as helps get rid of
syscon_regmap_lookup_by_pdevname() by removing the last known user.
* convert mach-davinci to use reset support available in watchdog driver
* a non-critical warning fix. It has been around since beginning so not sending
as a standalone fix for -rc cycle.
* moving mach-davinci clock init to .init_time() for legacy boot. This is
again in preparation for CCF conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2MBq
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.17/soc' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Pull "Miscellaneous DaVinci SoC support improvements for v4.17" from Sekhar Nori:
* rationalization of con_id names for phy clocks to make DT conversion easy
* A patch to move away from syscon as platform device. This is needed for
common clock framework conversion as well as helps get rid of
syscon_regmap_lookup_by_pdevname() by removing the last known user.
* convert mach-davinci to use reset support available in watchdog driver
* a non-critical warning fix. It has been around since beginning so not sending
as a standalone fix for -rc cycle.
* moving mach-davinci clock init to .init_time() for legacy boot. This is
again in preparation for CCF conversion.
* tag 'davinci-for-v4.17/soc' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: move davinci_clk_init() to init_time
ARM: davinci: board-da830-evm: fix unused const variable warning
ARM: davinci: remove watchdog reset
ARM: da8xx: use platform data for CFGCHIP syscon regmap
phy: da8xx-usb: rename clock con_ids
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FCaw
-----END PGP SIGNATURE-----
Merge tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Pull "ARM: Keystone DTS for 4.17" from Santosh Shilimkar:
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
* tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g: Fix unit-address formatting for serial nodes
dt-bindings: memory: ti-emif: add edac support under emif
ARM: dts: keystone-k2e-clocks: Fix missing unit address separator
ARM: dts: keystone-k2g: Move usb-phy nodes out of soc0
ARM: dts: keystone-k2g: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2g: Move keystone_irq to under device-state-control
ARM: dts: keystone-k2hk: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2l: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2e: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone: Move reset-controller to under device-state-control
ARM: dts: keystone: Move keystone_irq to under device-state-control
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
-----BEGIN PGP SIGNATURE-----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=SDoJ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omap variants for v4.17" from Tony Lindgren:
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
* tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap4-droid4: add soundcard
ARM: dts: motorola-cpcap-mapphone: add audio-codec
ARM: dts: omap3: Add missing #sound-dai-cells
ARM: dts: am43xx: add emif interrupt info
ARM: dts: am33xx: add emif interrupt info
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD SOM-LV
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD torpedo
ARM: dts: am4372: Mark omap_l3_noc with ti,no-idle
ARM: dts: am4372: Mark emif with ti,no-idle
ARM: dts: am33xx: Mark emif with ti,no-idle
ARM: dts: am4372: Add soc node
ARM: dts: am33xx: Add pm-sram phandle to soc node
ARM: dts: am4372: Update emif node
ARM: dts: am33xx: Update emif node
ARM: dts: am4372: Reserve pm code and data regions in ocmcram sram node
ARM: dts: am33xx: Reserve pm code and data regions in ocmcram sram node
ARM: dts: omap: Remove "cooling-{min|max}-level" for CPU nodes
ARM: dts: omap4-droid4: update touchscreen
ARM: dts: am33xx: add PDU001 board
ARM: dts: use 'atmel' as at24 manufacturer in am335x-boneblue
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix all DT dtc warnings when building with W=1
For most of implicated node, the addition of a fake reg property
fixes these warnings.
For others nodes, their location in device tree
have been updated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJak8PtAAoJEMrHeC97M/+mKkAQAIojX6u67lNj5lEW8MHbpzWa
q/61ofRqB36vuVRT8hL1rGyinubtzPxkwnyYbCdp5C5mu4qnpvXfW2AXqrGZTsdu
E91klWLigKArvKLTo8fC1bej1qz9ftHzB8xlyJKxokBcuqGO+QqeUgkImHjWHqJl
UST+vbCmY4VTlKnstoEfQDvrJELSgRDznzgqoAsDx/N6dh2jXrsIzEg/yPVQccgK
0v0mB+FdHjtvPX8hGh/YO+G5oaYQQEQkQB2+Q/5WJBivrRboNPM6tKKj8eJjbXAN
g/ssE0Wug+11dl2fNuuI98XCCzZng+Pj7RDGO+H54aR7o+i0HruMpEnZOZwClm1R
3rg8RrqBd9oD0tsLKve7TFKmG9ZvIDZZI6rIgZ+RIfcjrRRrY+N0/wmZnkCJPPJH
oTatUTBh5crgh22qcySIxz75oO3UJa6Ch12zx2kJjJKaMeV29UUwu4i11XXbowVK
bO3e296/BK3oExpFvmR73UtseeAb0CmQKvwiotNAr3jYE4YZH2taDLrcqnpTZXoP
0s+ao5kyT0iq1bJDZW7eds4KUOmDLhBY/sDfHVd+7qJHsfXpU4UOkyWz6qqw2GJ3
MkxLx3SJ+NFRTRL8oSPoab4cM1F+9qeC3SGqXjfjnQNb9DwXp+syvR18VcdHYQhx
/Dp3TWELf5nXZiTkLgVm
=raOr
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.17-round1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/dt
Pull "STi dts update" from Patrice Chotard:
Fix all DT dtc warnings when building with W=1
For most of implicated node, the addition of a fake reg property
fixes these warnings.
For others nodes, their location in device tree
have been updated.
* tag 'sti-dt-for-v4.17-round1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STi: Remove unused clk_ext2f_a9 clock
ARM: dts: STi: Update clocks node location
ARM: dts: STi: Update sound related nodes location
ARM: dts: STi: Add fake reg property for usb2_picophyX nodes
ARM: dts: STi: Add fake reg for restart, powerdown and picophy/softreset
ARM: dts: STi: Add fake reg property for remote processors
ARM: dts: STi: Add fake reg property for irq-syscfg
ARM: dts: STi: Add fake reg property for miphy28lp_phy
ARM: dts: STi: Add fake reg property for sti-display-subsystem
ARM: dts: STi: Move leds node outside soc node
ARM: dts: STi: Fix bindings notation
Instead of using PROPERTY_ENTRY_INTEGER() with explicitly supplied type,
use PROPERTY_ENTRY_U32() dedicated macro.
It will help modify internals of built-in device properties API.
No functional change intended.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Both cm-x300 and pxa3xx-ulpi use the plain clk_{en,dis}able() API.
With the new clocking framework this results in warnings of type:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:714 clk_core_enable+0x90/0x9c
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc5-cm-x300+ #15
Hardware name: CM-X300 module
[<c001007c>] (unwind_backtrace) from [<c000df94>] (show_stack+0x10/0x14)
[<c000df94>] (show_stack) from [<c00199a8>] (__warn+0xd8/0x100)
[<c00199a8>] (__warn) from [<c0019a0c>] (warn_slowpath_null+0x3c/0x48)
[<c0019a0c>] (warn_slowpath_null) from [<c024e8c0>] (clk_core_enable+0x90/0x9c)
[<c024e8c0>] (clk_core_enable) from [<c024ea54>] (clk_core_enable_lock+0x18/0x2c)
[<c024ea54>] (clk_core_enable_lock) from [<c0016994>] (cm_x300_u2d_init+0x4c/0xe8)
[<c0016994>] (cm_x300_u2d_init) from [<c00163e0>] (pxa3xx_u2d_probe+0xe0/0x244)
[<c00163e0>] (pxa3xx_u2d_probe) from [<c0283de0>] (platform_drv_probe+0x38/0x88)
...
------------[ cut here ]------------
and alike...
And finally, it results in:
------------[ cut here ]------------
pxa310_ulpi_poll: ULPI access timed out!
OTG transceiver init failed
------------[ cut here ]------------
It might be that disabling the warning in kernel config would also do
the job, but IMO a better solution would be to switch to
clk_prepare_enable() and clk_disable_unprepare() APIs.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
cm_x300_u2d_init() function is only used through its function pointer
that is passed through platform_data structure to the driver.
Therefore it can never be inlined.
Remove the inline directive.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Static checker reports the following warning:
arch/arm/mach-pxa/pxa3xx-ulpi.c:336 pxa3xx_u2d_probe()
warn: did you mean to pass the address of 'u2d'
Fix it by passing the correct pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
We can support USB OTG with MUSB driver on many ARM SoCs. Let's
enable all the SoCs with MUSB as loadable modules. And let's enable
their related DMA hardware.
And as MUSB is an USB OTG controller, let's enable OTG support too.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had 8250_OMAP working for few years now, so let's start enabling
it by default. We provide users an option to warn by default with
SERIAL_8250_OMAP_TTYO_FIXUP by default. That option updates the serial
console to point to 8250 driver and warns about it.
Users with ttyO[0123] in their /etc/inittab should update inittab
to use ttyS[0123] instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are needed to enable low-power suspend mode as described
by Dave.
Note that these depend on the am335x-pm-firmware.elf.
Cc: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have LIRC selected as a loadable module but it must now be
built-in. Let's update that and add few interesting new options
for blinking IR LEDs.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a common device tree for all Nuvoton NPCM750 BMCs and a board
specific device tree for the NPCM750 (Poleg) evaluation board.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Avi Fishman <avifishman70@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove 0x prefix from clkctrl unit address.
This silences the following dtc warning:
Warning (unit_address_format):
Node /clkctrl@0xf8000000 unit name should not have leading "0x"
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There has never been an artpec6 devboard produced
with less than 1 GiB RAM.
Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.
Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
The unit addresses on couple of serial nodes have a leading 0 resulting
in couple of warning messages around simple-bus unit address format
errors when compiled with W=1. Fix the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Commit 95d8b41c76 ("ARM: dts: keystone-k2e-clocks: Add missing unit
name to clock nodes that have regs") fixed the unit names on various
clock nodes but missed out adding the unit address separator on the
clkhyperlink0 clock node. Fix the same.
Fixes: 95d8b41c76 ("ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The two usb-phy nodes are not memory-mapped devices on the
SoC but rather dummy phys for SoCs with transparent autonomous
NOP phys. Move these to outside soc0 to their own node like
done elsewhere.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes warnings about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
gpio,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
The keystone_irq node describes a device that is a member of the device
state control module address space. As such, it should not be a member
of soc0 bus but instead a sub-node of device-state-control.
This move also fixes a warning about not having a reg property. Now
that this is a sub-node of device-state-control, a syscon type node,
we add this reg property but relative to the syscon base, this way
when the dt-binding/driver are updated we can drop the non-standard
ti,syscon-dev property completely and simply use get_resource() in
the driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Pull networking fixes from David Miller:
1) Use an appropriate TSQ pacing shift in mac80211, from Toke
Høiland-Jørgensen.
2) Just like ipv4's ip_route_me_harder(), we have to use skb_to_full_sk
in ip6_route_me_harder, from Eric Dumazet.
3) Fix several shutdown races and similar other problems in l2tp, from
James Chapman.
4) Handle missing XDP flush properly in tuntap, for real this time.
From Jason Wang.
5) Out-of-bounds access in powerpc ebpf tailcalls, from Daniel
Borkmann.
6) Fix phy_resume() locking, from Andrew Lunn.
7) IFLA_MTU values are ignored on newlink for some tunnel types, fix
from Xin Long.
8) Revert F-RTO middle box workarounds, they only handle one dimension
of the problem. From Yuchung Cheng.
9) Fix socket refcounting in RDS, from Ka-Cheong Poon.
10) Don't allow ppp unit registration to an unregistered channel, from
Guillaume Nault.
11) Various hv_netvsc fixes from Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (98 commits)
hv_netvsc: propagate rx filters to VF
hv_netvsc: filter multicast/broadcast
hv_netvsc: defer queue selection to VF
hv_netvsc: use napi_schedule_irqoff
hv_netvsc: fix race in napi poll when rescheduling
hv_netvsc: cancel subchannel setup before halting device
hv_netvsc: fix error unwind handling if vmbus_open fails
hv_netvsc: only wake transmit queue if link is up
hv_netvsc: avoid retry on send during shutdown
virtio-net: re enable XDP_REDIRECT for mergeable buffer
ppp: prevent unregistered channels from connecting to PPP units
tc-testing: skbmod: fix match value of ethertype
mlxsw: spectrum_switchdev: Check success of FDB add operation
net: make skb_gso_*_seglen functions private
net: xfrm: use skb_gso_validate_network_len() to check gso sizes
net: sched: tbf: handle GSO_BY_FRAGS case in enqueue
net: rename skb_gso_validate_mtu -> skb_gso_validate_network_len
rds: Incorrect reference counting in TCP socket creation
net: ethtool: don't ignore return from driver get_fecparam method
vrf: check forwarding on the original netdevice when generating ICMP dest unreachable
...
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 6cbfdd73a9 ("ARM: dts: add sysmmu nodes for exynos5250")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bypass-smu property is neither used nor documented in bindings.
Remove it from Xyref5260 board DTS.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
All the devices on I2C0 support fast mode, so increase the bus speed
to match. The Armada 388 is known to have a timing issue when in
standard mode, which we believe causes the ficticious device at 0x64
to appear.
[gregory.clement@bootlin.com: Note that since the commit fbffee7498
("ARM: dts: Fix I2C repeated start issue on Armada-38x") in 4.14, the
timing issue is managed for the Armada 38x SoCs.]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
dtc now gives the following warning:
arch/arm/boot/dts/rk3288-tinker.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /hdmi@ff980000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dtc now gives the following warning:
arch/arm/boot/dts/kirkwood-t5325.dtb: Warning (sound_dai_property): /sound/simple-audio-card,cpu:sound-dai: property size (4) too small for cell size 1
The binding documentation gives no indication what the cell size should
be (which should be fixed too), so just assume 0 is fine as that is what
the consumer has.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
To be able to reboot the platform we need to use armv7m_restart for STM32
SoCs using ARMv7 cores.
Fixes: e0644101bd2f ("ARM: mach-stm32: prepare stm32 family to welcome armv7 architecture)
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
As both STM32F4 and STM32F7 SoCs embeds an AMBA PL180 mmci IP,
we need to enable AMBA support in mach-stm32.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds initial support of STM32MP157 microprocessor (MPU)
based on Arm Cortex-A7. New Cortex-A infrastructure (gic, timer,...)
are selected if ARCH_MULTI_V7 is defined.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch prepares the STM32 machine for the integration of Cortex-A
based microprocessor (MPU), on top of the existing Cortex-M
microcontroller family (MCU). Since both MCUs and MPUs are sharing
common hardware blocks we can keep using ARCH_STM32 flag for most of
them. If a hardware block is specific to one family we can use either
ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch introduces the MACH_STM32F769 to make possible to only select
STM32F769 pinctrl driver.
By default, all the MACH_STM32Fxxx flags will be set with STM32 defconfig.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Replace sdio2 rcc hard coded clock value by its macro.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f769-disco board.
broken-cd property is needed as it misses a pullup on board
(resistor R76 is missing).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f746-eval board.
broken-cd property is needed as card detect signal is
connected to a GPIO expander which is not yet supported
in kernel linux.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
CONFIG_EXPERT exposes too many config options that do not matter for
development. E.g. it prohibits using the default values for the various
SH_SCI options. However, CONFIG_EMBEDDED selects CONFIG_EXPERT, so it
cannot be disabled.
Hence disable CONFIG_EMBEDDED, and compensate for the loss of
CONFIG_DEBUG_KERNEL by enabling the latter.
Actual impact, all harmless:
- CONFIG_NAMESPACES=y (plus a few related CONFIG_*_NS options),
- CONFIG_SYSCTL_SYSCALL=n,
- CONFIG_SERIAL_SH_SCI_NR_UARTS changed from 20 to 18,
- Some HID support became enabled,
- CONFIG_DEBUG_MEMORY_INIT=y,
Refresh the result.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the new bindings of the reworked Marvell NAND controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add sound support to Motorola Droid 4 using simple-soundcard
and CPCAP's audio codec. This does not yet correctly represent
the whole audio routing, since McBSP3 is also connected to
Bluetooth and MDM6600 modem (and probably also 4G modem).
These extra DAI links are not yet supported and have not been
tested.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for audio-codec to its DT file.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "enable arbiter" bit is available only for pxa3xx based platforms
but it was experimentally shown that even if this bit is reserved,
some Marvell platforms (64-bit) actually need it to be set. The driver
always set this bit regardless of this property, which is harmless.
Then this property is not needed.
The "num_cs" field is always 1 and for a good reason, the old driver
(pxa3xx_nand.c) could only handle one. The new driver that replaces it
(marvell_nand.c) can handle more, but better use device tree for such
description. As there is only one available chip select, there is no
need for an array of partitions neither an array of partition numbers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Magnus Damm