Commit Graph

775 Commits

Author SHA1 Message Date
Sripathy, Vishwanath 8640425b26 OMAP3: PM: Removing redundant and potentially dangerous PRCM configration
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.

Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:16:04 -08:00
Tero Kristo a087cad92c OMAP3: Fixed ARM aux ctrl register save/restore
Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:16:03 -08:00
Tero Kristo afbcf6197d OMAP3: CPUidle: Fixed timer resolution
Previously used u32 as temporary data storage that wraps around at 4.294s.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:16:02 -08:00
Sanjeev Premi a174e609b5 OMAP3: PM: Remove duplicate code blocks
This patch removes code blocks that are repeated
in function prcm_setup_regs().

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:16:01 -08:00
Tero Kristo f18cc2ff5e OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:16:00 -08:00
Tero Kristo b296c8118b OMAP3: PM: Enable system control module autoidle
Enable the auto-idle feature of the SCM block to save some additional
power.

Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:15:59 -08:00
Tero Kristo 2bbe3af3f1 OMAP3: PM: Ack pending interrupts before entering suspend
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20 18:15:58 -08:00
Olof Johansson 1daa8c1d75 omap: Enable GPMC clock in gpmc_init
Don't assume that gpmc_l3_clk is on, enable it before touching
configuration registers.

Note that the current code assumes that this clock is always
enabled. We are already setting smart idle and L3 autogating
for GPMC clock in gpmc_init.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-20 17:25:31 -08:00
Rajendra Nayak ecbb065947 OMAP4: clocks: Fix the clksel_rate struct DPLL divs
For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-20 13:35:28 -07:00
Rajendra Nayak 0324f59fc9 OMAP4: PRCM: Fix the base address for CHIRONSS reg defines
The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-20 13:35:27 -07:00
Tony Lindgren e9acb9b64d omap3: Fix cpu detection
We need to set the omap_chip.oc carefully for the clocks to work.

To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.

Also add handling for 34xx es3.1.2 as es3.1 for now.

Fixes booting on at least overo board.

Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19 18:17:36 -08:00
Tony Lindgren d4bb72e50a omap: Fix functions for dynamic remuxing of pins
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.

In some cases we want to change the signals dynamically,
mostly for power management.

Note that we cannot use the signal names as they are set
__init to save memory.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19 18:17:35 -08:00
Tony Lindgren 2cb0c54f3a omap: Fix cmdline muxing
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.

Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().

Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-19 18:17:07 -08:00
Russell King 6468e3b187 OMAP3: clock: Remove unnecessarily .init initializers from OMAP3 clocks
The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk.  Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.

Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-19 17:30:52 -07:00
Thara Gopinath 883edfdd58 OMAP3: hwmod: Adding flag to prevent caching of sysconfig register.
In the current implementation the sysconfig value is read into
 _sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.

        a. The module sets the sysconfig register through omap_device_enable.
           Here _sysc_cache is updated with the value written to the sysconfig
           register and left.
        b. The power domain containig the module enters off mode and the
           module context is lost.
        c. The module in use becomes active and calls omap_device_enable to
           enable itself. Here a read of sysconfig register does not happen
           as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
           to the sysconfig register will be same as the one written in step a.
           Since _sysc_cache reflects the previous written value an update
           of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.

This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.

This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.

Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-19 17:30:51 -07:00
Tony Lindgren 27dba4bcf8 Merge branch 'for_2.6.33rc_c' of git://git.pwsan.com/linux-2.6 into omap-fixes-for-linus 2010-01-08 14:27:56 -08:00
Paul Walmsley cdf1a91556 OMAP2 clock: dynamically allocate CPUFreq frequency table
Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time.  This also reduces the size
of the CPUFreq frequency table.

Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-08 15:23:17 -07:00
Paul Walmsley ca6eccb31e OMAP2xxx OPP: clean up comments in OPP data
Revise some of the comments in the OMAP2xxx OPP data for clarity.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
2010-01-08 15:23:15 -07:00
Felipe Balbi 19fe458310 OMAP2xxx clock: clk2xxx.c doesn't compile if CPUFREQ is enabled
if we enable CPUFREQ we can't build omap2 for two reasons,
one of them is fixed by the patch below.

It's failing because the __must_be_array() check in
ARRAY_SIZE() is failing and printing the following message:

arch/arm/mach-omap2/clock2xxx.c:453: error: negative width in bit-field '<anonymous>'

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
[paul@pwsan.com: commit message updated; changed rate variable name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-08 15:23:15 -07:00
Tuukka Toivonen 3e3ee1560d OMAP3 clock: Add capability to change rate of dpll4_m5_ck
Add necessary definitions to clock framework to allow changing
dpll4_m5_ck rate.  This is used by the camera code.

Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-08 15:23:08 -07:00
Paul Walmsley 073463ca40 OMAP3 clock: McBSP 2, 3, 4 functional clock parent is PER_96M_FCLK, not CORE_96M_FCLK
The correct parent of the McBSP 2, 3, and 4 functional clocks is
PER_96M_FCLK, not CORE_96M_FCLK.  Fix this in the OMAP clock tree.
Reported by Nicole Chalhoub <n-chalhoub@ti.com>.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
2010-01-08 15:23:07 -07:00
Kevin Hilman 9b5bc5fa4b OMAP3: clock: add clockdomains for UART1 & 2
UART1 & 2 were missing clockdomains resulting in broken omap_hwmod
init for these devices.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-08 15:23:06 -07:00
Paul Walmsley 7adb998717 OMAP2xxx IO mapping: mark DSP mappings as being 2420-only
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420.  The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-08 15:23:05 -07:00
Abhijit Pagare 98bb155130 ARM: OMAP3: PM: Fix the Invalid CM_CLKSTCTRL reg access.
In OMAP2/3 some of the clock-domains which did not have control
facility were being falsely written to and read using the CM_CLKSTCTRL
register though it did not exist for them. One check is added to remove
this flaw.

Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
2010-01-08 15:23:04 -07:00
Huang Weiyi 48bca0e9c7 OMAP2: remove duplicated #include
Remove duplicated #include('s) in
  arch/arm/mach-omap2/clock34xx.c
  arch/arm/mach-omap2/io.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-01-08 15:23:03 -07:00
Vaibhav Hiremath 342aa2c172 omap3: EVM: Choose OMAP_PACKAGE_CBB
Without this the kernel doesn't boot, it craches in
omap_mux_package_fixup(), since the package_subset becomes NULL.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08 10:29:08 -08:00
Tony Lindgren d04eb60066 omap3: Fix booting if package is uninitialized
Otherwise bringing up new boards can be harder:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.33-rc2-00015-g0bc9c93-dirty #37)
PC is at omap_mux_init+0xa4/0x3d8
LR is at omap_mux_init+0x3c/0x3d8
...

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08 10:29:08 -08:00
Roel Kluin 1b6e821f23 omap3: add missing parentheses
`!' has a higher precedence than `&' so parentheses are required.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08 10:29:07 -08:00
Vimal Singh 6b06ebdfbd omap2/3: ZOOM: Correcting key mapping for few keys
Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.

Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08 10:29:07 -08:00
Alexander Shishkin 9230372aee omap2/3: make serial_in_override() address the right uart port
Commit f62349ee97 makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.

Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-08 10:29:06 -08:00
Mika Westerberg f2eeeae06a OMAP3: serial - fix bug introduced in
Commit f62349ee97 had side effect that
causes kernel to oops when we are suspending to ram:

	# echo mem > /sys/power/state

	WARNING: at kernel/irq/manage.c:858 __free_irq+0x90/0x174()
	Trying to free already-free IRQ 72
	Modules linked in:
	Backtrace:
	[<c00328d0>] (dump_backtrace+0x0/0x110) from [<c0347298>] (dump_stack+0x18/0x1c)
	 r7:dfd4be08 r6:c009505c r5:c03fbfd1 r4:0000035a
	[<c0347280>] (dump_stack+0x0/0x1c) from [<c005a408>] (warn_slowpath_common+0x50/0x68)
	[<c005a3b8>] (warn_slowpath_common+0x0/0x68) from [<c005a46c>] (warn_slowpath_fmt+0x30)
	 r7:c0474afc r6:00000048 r5:00000000 r4:c0474ac0
	[<c005a43c>] (warn_slowpath_fmt+0x0/0x38) from [<c009505c>] (__free_irq+0x90/0x174)
	 r3:00000048 r2:c03fc0ef
	[<c0094fcc>] (__free_irq+0x0/0x174) from [<c0095184>] (free_irq+0x44/0x64)
	[<c0095140>] (free_irq+0x0/0x64) from [<c0038100>] (omap_uart_enable_irqs+0x4c/0x90)
	 r7:c034d58c r6:00000003 r5:00000000 r4:c0463028
	[<c00380b4>] (omap_uart_enable_irqs+0x0/0x90) from [<c003d8f8>] (omap3_pm_begin+0x1c/0)
	 r5:00000003 r4:00000000
	[<c003d8dc>] (omap3_pm_begin+0x0/0x28) from [<c008d008>] (suspend_devices_and_enter+0x)
	[<c008cfd8>] (suspend_devices_and_enter+0x0/0x1dc) from [<c008d29c>] (enter_state+0xe8)
	 r5:c03f7f46 r4:00000000
	[<c008d1b4>] (enter_state+0x0/0x140) from [<c008c8e0>] (state_store+0x9c/0xc4)
	 r7:c034d58c r6:00000003 r5:00000003 r4:c03f7f46
	[<c008c844>] (state_store+0x0/0xc4) from [<c01cb2dc>] (kobj_attr_store+0x20/0x24)
	[<c01cb2bc>] (kobj_attr_store+0x0/0x24) from [<c0119420>] (sysfs_write_file+0x114/0x14)
	[<c011930c>] (sysfs_write_file+0x0/0x148) from [<c00cb298>] (vfs_write+0xb8/0x164)
	[<c00cb1e0>] (vfs_write+0x0/0x164) from [<c00cb408>] (sys_write+0x44/0x70)
	 r8:4001f000 r7:00000004 r6:df81bd00 r5:00000000 r4:00000000
	[<c00cb3c4>] (sys_write+0x0/0x70) from [<c002f040>] (ret_fast_syscall+0x0/0x38)
	 r8:c002f204 r7:00000004 r6:401fa5e8 r5:4001f000 r4:00000004

This is due the fact that uart_list list was populated in
omap_serial_early_init() and omap_uart_enable_irqs() went through this
list even when serial idle wasn't enabled for all uarts.

This patch moves the code that populates the uart_list and enables uart
clocks into omap_serial_init_port().

Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-16 12:44:04 -08:00
Balaji T K ebeb53e1e1 mfd: twl: fix twl4030 rename for remaining driver, board files
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.

This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.

Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-16 12:44:04 -08:00
Olof Johansson 35358281bb omap3: Allow EHCI to be built on OMAP3
OMAP34XX has EHCI, so select USB_ARCH_HAS_EHCI.

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-15 10:34:12 -08:00
Santosh Shilimkar b07682b605 mfd: Rename twl4030* driver files to enable re-use
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.

This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 20:05:51 +01:00
Amit Kucheria 3c684e84d1 mfd: Optimised twl4030-power power scripts for the rx51
The power scripts optimisation was mainly done by:
Tero Kristo <tero.kristo@nokia.com> and
Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>

I'm only refactoring and testing it against the mainline kernel.

Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: linux-omap@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 19:21:29 +01:00
vikram pandita ce13d4716a omap: serial: fix non-empty uart fifo read abort
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.

OMAP3xxx:
	UART IP revision >= 0x52 have this issue
	MVR register format is:
	Bits  Field Name  Description  				Type  Reset
	31:8   RESERVED 					RO  	0x0
	7:4    MAJOR  	Major revision number of the module.  	RO  	0x--
	3:0    MINOR  	Minor revision number of the module.  	RO  	0x--

OMAP4xxx:
	All revisions have this issue
	Revision id check is not used as the format of MVR resigster has changed
	For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
	Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
	Bits  Field Name  Description  				Type  Reset
	31:30 SCHEME  	Scheme revision number of module  	RO  	0x1
	29:28 RESERVED   					RO  	0x1
	27:16 FUNC  	Function revision number of module  	RO  	0x041
	15:11 RTL  		Rtl revision number of module  	RO  	0x00
	10:8  MAJOR 	Major revision number of the module.  	RO  	0x6
	7:6   CUSTOM  	Custom revision number of the module.  	RO  	0x0
	5:0   MINOR  	Minor revision number of the module.  	RO  	0x02

Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty

tested on zoom3(3630) board

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:37 -08:00
Madhusudhan Chikkature ed32350dc5 omap3: Zoom2/3: Update hsmmc board config params
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable

Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:37 -08:00
Sergey Lapin 0712fb39d7 omap3: id code detection 3525 vs 3515
The runtime detection of OMAP3515 and OMAP3525
was reversed.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:37 -08:00
Kalle Valo 860fc97632 omap3: rx51: Use wl1251 in SPI mode 3
Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:37 -08:00
Anand Gadiyar aed79bce77 omap3: zoom2/3: make MMC slot work again
omap3: zoom2/3: make MMC slot work again

Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:36 -08:00
Mika Westerberg f62349ee97 OMAP3: serial - allow platforms specify which UARTs to initialize
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.

Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:35 -08:00
Mike Rapoport edc961a2fa omap3: cm-t35: add mux initialization
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:35 -08:00
Santosh Shilimkar b2f5c9413c OMAP4: Remove the secondary wait loop
The secondary cores wakes up in time so the wait loop is not
necessary anymore.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:35 -08:00
Santosh Shilimkar 942e2c9e52 OMAP4: AuxCoreBoot registers only accessible in secure mode
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:35 -08:00
Santosh Shilimkar b570e0ec25 OMAP4: Fix cpu detection
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.

Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:34 -08:00
Grazvydas Ignotas 8d88f7f70c omap3: pandora: board file updates for .33
Pandora board file updates:
- change keycodes of game buttons
  it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
  this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
  the older DSS driver was never functional on l-o or mainline
  kernels due to missing panel driver, so remove unneeded
  pandora_lcd platform_device. This also removes last OMAP_TAG
  from the board file.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:34 -08:00
Gregoire Gentil 7a079cab46 omap3: Board file of Always Innovating OMAP3-based Touch Book
Board file of Always Innovating OMAP3-based Touch Book

Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:34 -08:00
Ladislav Michl 3bc4801478 omap: use smc91x_platdata to setup smc91x
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:33 -08:00
Tony Lindgren 662c8b55d2 omap: mux: Add 36xx CBP package support
Add 36xx CBP package support

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:33 -08:00
Tony Lindgren 15f45e6f27 omap: mux: Remove old mux code for 34xx
Remove old mux code for 34xx

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:33 -08:00
Tony Lindgren 4896e3940a omap: mux: Replace omap_cfg_reg() with new style signal or gpio functions
Replace omap_cfg_reg() with new style signal or gpio functions

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Tony Lindgren b63128e812 omap: Split i2c platform init for mach-omap1 and mach-omap2
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.

Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.

Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Tony Lindgren 4b715efccf omap: mux: Add debugfs support for new mux code
Add debugfs support for new mux code

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Tony Lindgren ca5742bdb5 omap: mux: Add new style init functions to omap3 board-*.c files
Add new style mux init functions to omap3 board-*.c files

So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Tony Lindgren ddaa912a21 omap: mux: Add new style pin multiplexing data for 34xx
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.

Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.

Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Tony Lindgren 15ac7afe51 omap: mux: Add new style pin multiplexing code for omap3
Initially only for 34xx. This code allows us to:

- Make the code more generic as the omap internal signal
  names can stay the same across omap generations for some
  devices

- Map mux registers to GPIO registers that is needed for
  dynamic muxing of pins during off-idle

- Override bootloader mux values via kernel cmdline using
  omap_mux=some.signa1=0x1234,some.signal2=0x1234

- View and set the mux registers via debugfs if
  CONFIG_DEBUG_FS is enabled

Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:32 -08:00
Mike Rapoport 92c9f50189 omap2: mux: intoduce omap_mux_{read,write}
intoduce omap_mux_{read,write}

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-12-11 16:16:31 -08:00
Rajendra Nayak 911bd7395c ARM: OMAP4: PM: Add init api for DPLL nodes
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:47 -07:00
Rajendra Nayak 16975a79c8 ARM: OMAP4: PM: Add support for OMAP4 dpll api's
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:46 -07:00
Rajendra Nayak a1391d2768 ARM: OMAP4: PM: Move DPLL control apis to dpll.c
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:46 -07:00
Rajendra Nayak d79b126724 ARM: OMAP4: PM: Add dummy hooks for OMAP4 dpll api's
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:46 -07:00
Rajendra Nayak 972c542746 ARM: OMAP4: PM: OMAP4 clock tree and clkdev registration
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak dd7084138f ARM: OMAP4: PM: Adds CM1/2 register field masks
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak 234f0c4c66 ARM: OMAP4: PM: Adds PRM register shift and mask bits
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak c1294045d2 ARM: OMAP4: PM: Adds PRM register defs for OMAP4
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak 9b47267f3e ARM: OMAP4: PM: Adds CM1/2 register defs for OMAP4
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak 77772d5f7d ARM: OMAP4: PM: PRM/CM module offsets for OMAP4
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:45 -07:00
Rajendra Nayak 9ef89150ea ARM: OMAP4: PM: Fix the PRM and CM base addresses
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
2009-12-11 17:00:44 -07:00
Kevin Hilman 81d7c6ffcc OMAP: hwmod: warn on missing clockdomain
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 17:00:44 -07:00
Paul Walmsley a16b1f7f86 OMAP3 hwmod: drop most of the OCP_SYSCONFIG.CLOCKACTIVITY code
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates.  This was a misapprehension.  The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request.  This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.

In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled.  We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa).  In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.

This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Sebastien Sabatier <s-sabatier1@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
2009-12-11 17:00:43 -07:00
Paul Walmsley 718bfd7693 OMAP hwmod: add names to module MPU IRQ lines
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info.  Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.

Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2009-12-11 17:00:43 -07:00
Paul Walmsley 726072e5dd OMAP3 hwmod: Add automatic OCP_SYSCONFIG AUTOIDLE handling
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.

After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable.  If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable.  Upon module disable, AUTOIDLE will be set to
1.

Enabling module autoidle should save some power.  The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.

Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-12-11 17:00:43 -07:00
Paul Walmsley b835d01421 OMAP3 hwmod: reprogram OCP_SYSCONFIG register after setting SOFTRESET
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1).  This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.

Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-12-11 17:00:43 -07:00
Paul Walmsley 6f8b7ff5b0 OMAP clock/hwmod: fix off-by-one errors
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.

This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>.  A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
2009-12-11 17:00:43 -07:00
Thara Gopinath 3863c74b51 OMAP3: PM: Fix for MPU power domain MEM BANK position
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position

Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 17:00:42 -07:00
Paul Walmsley 18862cbe47 OMAP3: SDRC: Place SDRC AC timing and MR changes in CORE DVFS SRAM code behind Kconfig
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers.  This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state.  This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on.  Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM.  At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders.  Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.

This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.

Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Christophe Sucur <c-sucur@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Olof Johansson <olof@lixom.net>
2009-12-11 17:00:42 -07:00
Roel Kluin 1fda39e6fd OMAP2/3 powerdomain: return errors rather than returning the output of IS_ERR()
IS_ERR returns only 1 or 0, and the functions return a negative error
in other cases anyways.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 17:00:41 -07:00
Paul Walmsley 2354eb5a94 OMAP powerdomain/PM: use symbolic constants for the max number of power states
Replace some bare constants with power states.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2009-12-11 17:00:41 -07:00
Paul Walmsley 6a06fa6863 OMAP clockdomain/powerdomain: optimize out sleepdep code on OMAP24xx
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 17:00:41 -07:00
Paul Walmsley 33903eb55a OMAP clockdomain/powerdomain: remove CONFIG_OMAP_DEBUG_{CLOCK,POWER}DOMAIN
Avoid cluttering the Kconfig space with debug options that are rarely
used.  These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.

Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs.  Convert most
of them to use tabs.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
2009-12-11 17:00:40 -07:00
Paul Walmsley 42d75e7df3 OMAP2/3 PRCM: don't export prm_*(), cm_*() functions
Device drivers and loadable modules should not be calling these
prm_* and cm_* functions, so stop exporting them.  Only core code
and device driver integration code (in arch/arm/*omap*) should
call these functions.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 17:00:40 -07:00
Paul Walmsley d8a944582d OMAP2 clock: convert clock24xx.h to clock2xxx_data.c, opp2xxx*
The OMAP2 clock code currently #includes a large .h file full of static
data structures.  Instead, define the data in a .c file.

Russell King <linux@arm.linux.org.uk> proposed this new arrangement:

    http://marc.info/?l=linux-omap&m=125967425908895&w=2

This patch also deals with most of the flagrant checkpatch violations.

While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device.  This should save some memory.  In the long run,
these prcm_config tables should be replaced with OPP code.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
2009-12-11 16:16:00 -07:00
Paul Walmsley 82e9bd5885 OMAP3 clock: convert clock34xx.h to clock34xx_data.c
The OMAP3 clock code currently #includes a large .h file full of static
data structures.  Instead, define the data in a .c file.

Russell King <linux@arm.linux.org.uk> proposed this new arrangement:

    http://marc.info/?l=linux-omap&m=125967425908895&w=2

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
2009-12-11 16:12:15 -07:00
Paul Walmsley 75d4334011 OMAP2xxx clock: remove implicit dependency between rate CPU flag and clkdev_omap CPU flag
cpu_mask is reused in the OMAP2xxx clock code to match against both the
CPU-specific rate flags (e.g., RATE_IN_2420) and the OMAP clkdev integration
code CPU flags (e.g., CK_242X).  This means that any patch that renumbers the
CK_* macros, as the next patch does, will probably break.  This patch
separates the clkdev_omap and clksel_rate CPU type detection flags so
the CK_* macros can be renumbered freely.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 16:12:11 -07:00
Paul Walmsley 55d8a65308 OMAP2/3: move SDRC macros to mach-omap2/sdrc.h
clock34xx.c contains some macros which probably belong in mach-omap2/sdrc.h.
Move those macros to mach-omap2/sdrc.h.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 16:12:11 -07:00
Paul Walmsley 06b16939a3 OMAP2 clock: APLL code shouldn't rely on static clocks in its local namespace
Similar to the previous patch, the APLL code relied on the presence of the
static struct clks in its own namespace.  The APLL code didn't use them for
validation, however - it adjusted its own internal state depending on
the struct clk * that called it.  Now that static struct clks are
leaving the clock24xx.c namespace, use a more durable method: split the
omap2_clk_fixed_enable() function into omap2_clk_apll96_enable() and
omap2_clk_apll54_enable().  They still share a disable function.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 16:12:11 -07:00
Paul Walmsley ebd893ded2 OMAP1/2/3 clock: remove paranoid checks in preparation for clock{,2xxx,3xxx}_data.c
Some parts of the clock code took advantage of the fact that the statically
allocated clock tree was in clock{,24xx,34xx}.c's local namespace to do some
extra argument checks.  These are overzealous and are more difficult to
maintain when the clock tree is in a separate namespace, so, remove them.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2009-12-11 16:12:07 -07:00
Tomi Valkeinen d9056ce2af OMAP: SDP: Enable DSS2 for OMAP3 SDP board
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2009-12-09 18:29:38 +02:00
Tomi Valkeinen afedec183e OMAP: Add VRAM manager
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:

- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations

The upcoming DSS2 uses VRAM manager.

VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
2009-12-09 12:04:33 +02:00
Tomi Valkeinen dadd2bb931 OMAP: OMAPFB: add omapdss device
The upcoming new display subsystem driver is divided to two devices,
omapdss and omapfb, of which omapdss handles the actual hardware.

This patch adds a dummy omapdss platform device for the current omapfb
driver, which is then used to get the clocks. This will make it possible
for the current and the new display drivers to co-exist.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2009-12-09 12:04:32 +02:00
Tomi Valkeinen 91773a00f8 OMAP: OMAPFB: split omapfb.h
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:

include/linux/omapfb.h - ioctls etc for userspace and some kernel
                         stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use

This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2009-12-09 12:04:06 +02:00
Tomi Valkeinen b90f8e7296 OMAP2: Add funcs for writing SMS_ROT_* registers
SMS_ROT_* registers are used by VRFB rotation engine.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
2009-12-09 11:44:32 +02:00
Linus Torvalds 1c496784a0 Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits)
  arm: omap: Add omap3_defconfig
  AM35xx: Defconfig for AM3517 EVM board
  AM35xx: Add support for AM3517 EVM board
  omap: 3630sdp: defconfig creation
  omap: 3630sdp: introduce 3630 sdp board support
  omap3: Add defconfig for IGEP v2 board
  omap3: Add minimal IGEP v2 support
  omap3: Add CompuLab CM-T35 defconfig
  omap3: Add CompuLab CM-T35 board support
  omap3: rx51: Add wl1251 wlan driver support
  omap3: rx51: Add SDRAM init
  omap1: Add default kernel configuration for Herald
  omap1: Add board support and LCD for HTC Herald
  omap: zoom2: update defconfig for LL_DEBUG_NONE
  omap: zoom3: defconfig creation
  omap3: zoom: Introduce zoom3 board support
  omap3: zoom: Drop i2c-1 speed to 2400
  omap3: zoom: rename zoom2 name to generic zoom
  omap3: zoom: split board file for software reuse
  omap3evm: MIgrate to smsc911x ethernet driver
  ...

Fix trivial conflict (two unrelated config options added next to each
other) in arch/arm/mach-omap2/Makefile
2009-12-08 08:15:29 -08:00
Linus Torvalds 79c9601c2e Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (272 commits)
  Fix soc_common PCMCIA configuration
  ARM: 5827/1: SA1100: h3100/h3600: emit messages on failed gpio_request
  ARM: 5826/1: SA1100: h3100/h3600: always build htc-egpio driver
  ARM: 5825/1: SA1100: h3600: update defconfig
  ARM: 5824/1: SA1100: reuse h3600 PCMCIA driver on h3100
  ARM: 5823/1: SA1100: h3100/h3600: add support for gpio-keys
  ARM: 5822/1: SA1100: h3100/h3600: clean up #includes
  ARM: 5821/1: SA1100: h3100/h3600: revise copyright boilerplates
  ARM: 5820/1: SA1100: h3100/h3600: split h3600.c
  ARM: 5819/1: SA1100: h3100/h3600: merge h3600.h and h3600_gpio.h into h3xxx.h
  ARM: 5818/1: SA1100: h3100/h3600: drop old GPIO definitions
  ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs
  ARM: 5816/1: SA1100: h3600: remove IRQ_GPIO_* definitions
  ARM: 5815/1: SA1100: h3100/h3600: remove now unused assign_h3600_egpio handlers
  ARM: 5814/1: SA1100: h3100/h3600: convert all users of assign_h3600_egpio to gpiolib
  ARM: 5813/1: SA1100: h3100/h3600: add htc-egpio driver
  ARM: 5812/1: SA1100: h3100/h3600: separate machine-specific LCD helpers
  ARM: 5811/2: pcmcia: convert sa1100_h3600 driver to gpiolib
  ARM: 5799/1: SA1100: h3600: stop setting direction for LCD pins
  ARM: 5798/1: SA1100: h3600: remove unused cruft from h3600.h
  ...
2009-12-08 08:12:43 -08:00
Takashi Iwai baf9226667 Merge branch 'topic/asoc' into for-linus 2009-12-04 16:22:41 +01:00
Alexander Shishkin 183bd50f4f ARM: 5843/1: OMAP3: add AMBA devices for ETM and ETB
This enables on-chip tracing components found in omap3xxx.

Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-12-02 10:25:23 +00:00
Ranjith Lohithakshan c625327e2f AM35xx: Add support for AM3517 EVM board
This patch creates a minimal AM3517 EVM board support.

Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25 14:21:01 -08:00
vikram pandita 34c9ac2376 omap: 3630sdp: introduce 3630 sdp board support
Add 3630SDP board support

The board shares the same peripherals as a zoom2 main.
So reuse the peripheral file of zoom platform.

Peripheral    zoom2    zoom3  sdp3630
---------------------------------------
Ethernet	smsc	smsc	smc
NOR		n/a     n/a	B
Onenand	  	n/a     n/a	B
HDMI		A	A	B (persent on different i2c)
NAND		A	A	A (same nand)
SDRAM		A	A	A (same sdram)
Keypad		A	A	A (same twl)
Camera		A	A	A (same sensor can be mounted)
LCD Display	A	A	A (same wvga display)
OPPs		A	A	A (same chip feature)
Audio		A	A	A (same audio via twl5030)

OMAP3630 details can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25 14:21:01 -08:00
Enric Balletbo i Serra 58e111621d omap3: Add minimal IGEP v2 support
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25 14:21:00 -08:00
Mike Rapoport 2886d128d8 omap3: Add CompuLab CM-T35 board support
This patch adds basic support for CompuLab CM-T35 module.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-11-25 14:21:00 -08:00