Y41x formats is a 4:4:4 format, so it can be addressed with pixel level accuracy.
Meanwhile it seems that while rotating YUYV 4:2:2 formats need a multiple of 2
for width and height, otherwise corruption occurs.
For YUV 4:2:2, the spec says that w/h should always be even, but we get
away with odd height while unrotated. When rotating it seems corruption
occurs with an odd x/y, and w/h should always be even.
Just to be completely paranoid, reject odd x/y w/h when rotating 90/270.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322135954.20434-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The intent was to expose these as part of the means to perform full
context recovery (though not the SINGLE_TIMELINE, that is for later and
just sucked as collateral damage). As that requires a couple more
patches to complete the series, roll back the earlier chunks of ABI for
an intervening PR. We keep all the internals intact and under selftests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327105814.14694-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This is to disable semaphore usage when on vGPU for now. Unfortunately
GVT-g hasn't fully enabled semaphore usage yet, so current guest with
semaphore use would cause vGPU failure.
Although current semaphore failure with vGPU can be simply resolved by
allowing cmd parser to accept MI_SEMAPHORE_WAIT command with address
audit, we're checking general usage of semaphore and how we should
handle it properly for virtualization in consider of function and
security concern. So we decide to request to disable it for now in
guest driver. Once GVT could support it, we would add new compat bit
to turn it on.
Fixes: e886196469 ("drm/i915: Use HW semaphores for inter-engine synchronisation on gen8+") #vgpu
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190327090636.3547-1-zhenyuw@linux.intel.com
Update the DP MSA MISC bits for fastsets. This is needed
when we change between limited and full range RGB output.
On HSW+ changing limited_range does not currently result in a
full modeset since we have don't have the readout code for it
(for DP we could, and probably should, readout from TRANS_MSA_MISC
itself, for HDMI we would have to rely on the infoframe). So
the PIPE_CONF_CHECK() is only performed for pre-HSW platforms.
That means any change in the value will result in a fastset
instead. Fortunately there is no prohibition to changing
TRANS_MSA_MISC dynamically, so it looks like we can legally do
fastsets for this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-5-ville.syrjala@linux.intel.com
Allow DP MST to output any color depth. This means deep color as
well as falling back to 6bpc if we would otherwise require too
much bandwidth.
TODO: We should probably extend bw_contstrained scheme to force
all streams on the link to 6bpc if we can't fit the new stream(s)
otherwise.
v2: Use a proper for-loop (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190326142556.21176-3-ville.syrjala@linux.intel.com
Looks like EDID_QUIRK_FIRST_DETAILED_PREFERRED never did anything.
Its counterpart in f86EdidModes.c is properly hooked up but somehow
that functionality was lost when it was copied into the kernel.
The concensus seems to be that this quirk is a bit misguided
anyway so let's nuke the leftovers.
For posterity here are some links to known cases:
* Proview AY765C
https://bugs.freedesktop.org/show_bug.cgi?id=15160
* Unknown Acer
https://bugzilla.redhat.com/show_bug.cgi?id=284231 (got the
reference from xf86EdidModes.c)
* Peacock Ergovision 19 (only in xf86EdidModes.c)
https://bugzilla.redhat.com/show_bug.cgi?id=492359
* Philips 107p5 CRT
"Reported on xorg@ with pastebin", didn't find the mail(s)
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322174244.23945-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
drm_display_info.name is only ever set by a few panel drivers but
never actually used anywhere except in i915 debugfs code. Trash it.
v2: Fix typo in commit msg (Sam Ravnborg)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326173401.7329-3-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should not result in any changes.
v2: Rebase
v3: Don't forget to remove the info->par assignment (Noralf)
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Emil Lundmark <lndmrk@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-19-daniel.vetter@ffwll.ch
This should not result in any changes.
v2: Rebase over vbox changes - vbox gained it's own line to fill
fix.id.
v3: Rebase
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-20-daniel.vetter@ffwll.ch
Another driver that didn't set fbinfo->fix.id before.
v2: Fix subject and rebase
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-18-daniel.vetter@ffwll.ch
This changes the fb name from "nouveaufb" to "nouveaudrmfb".
Aside: I wonder whether the in_interrupt() check is good enough for
the nouveau acceleration. Cargo-cult says drm_can_sleep() is needed,
which isn't actually working if you pick a .config without PREEMPT.
For the generic fbdev defio support we've gone with offloading
everything to a worker. For the non-accel callbacks (set_par, blank
and friends) checking for oops_in_progress is good enough to catch all
the evil calling contexts.
v2: Rebase
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-14-daniel.vetter@ffwll.ch
Only changes the name of the fb from "mgadrmfb" to "mga200drmfb".
v2: Rebase
v3: Note the name change (Noralf)
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-12-daniel.vetter@ffwll.ch
This changes the fb name from "inteldrmfb" to "i915drmfb".
v2: Rebase
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-11-daniel.vetter@ffwll.ch
Should not result in any changes.
v2: Rebase
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Ajit Negi <ajitn.linux@gmail.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: John Garry <john.garry@huawei.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-10-daniel.vetter@ffwll.ch
This will change the fb name from "psbdrmfb" to "gma500drmfb".
v2: Rebase
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-9-daniel.vetter@ffwll.ch
Should not result in any changes.
v2: Rebase
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-6-daniel.vetter@ffwll.ch
Only changes the name of the fb from "armada-drmfb" to armadadrmfb.
v2: Rebase
v3: Fix commit message (Noralf)
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-5-daniel.vetter@ffwll.ch
Should not cause any changes.
v2: Rebase
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Shirish S <shirish.s@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-4-daniel.vetter@ffwll.ch
The fbdev emulation helpers pretty much assume that this is set.
Let's do it for everyone.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-3-daniel.vetter@ffwll.ch
Looking at the oldest/most popular drivers ${driver}drmfb seems to be
the standard, except i915.ko went with "inteldrmfb". I guess renaming
that for consistency won't hurt, it definitely confused me when I
started with kms 10 years ago.
I hope this never became uapi ... worst case drivers can overwrite it
after having called fill_info().
Since subsequent patches change this for some drivers later on in the
series, here's the exhaustive list of where all fix.id is used:
- /proc/fb which prints the minor number and fix.id name.
- per-fb sysfs name file
- getfix ioctl, which is used by fbset only to print out the name when
dumping information
- lots and lots of places in dmesg, anytime anything happens with an
fbdev really
I think minimal to 0 chances that changing this will screw up a config
script or something, since outside of informational message it's not
used by anything to identify which fbdev maps to which minor. After
all the last fbset release is from 1999, and that predates even devfs
I think.
v2: Rebase and amend commit message, thanks to Ilia for pointing out
that this needs to be spelled out.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-2-daniel.vetter@ffwll.ch
The fbdev split between fix and var information is kinda
pointless for drm drivers since everything is fixed: The fbdev
emulation doesn't support changing modes at all.
Create a new simplified helper and use it in the generic fbdev
helper code. Follow-up patches will beef it up more and roll
it out to all drivers.
v2: We need to keep sizes, since they might not match the fb dimensions
(Noralf)
v3: Fix typo in commit message and remove extraneous line in kerneldoc (Noralf)
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326132008.11781-1-daniel.vetter@ffwll.ch
When building with ARCH=i386, readq and writeq are not defined,
resulting in:
intel_uncore.h: In function ‘__raw_uncore_read64’:
intel_uncore.h:257:9: error: implicit declaration of function ‘readq’;
did you mean ‘readl’? [-Werror=implicit-function-declaration]
return read##s__(uncore->regs + i915_mmio_reg_offset(reg)); \
^
and:
intel_uncore.h: In function ‘__raw_uncore_write64’:
intel_uncore.h:264:2: error: implicit declaration of function ‘writeq’;
did you mean ‘writel’? [-Werror=implicit-function-declaration]
write##s__(val, uncore->regs + i915_mmio_reg_offset(reg)); \
^
Add the io-64-nonatomic-lo-hi include to have readq and writeq available
for all builds. This header internally includes linux/io.h, so the
native readq and writeq definitions will be used when available.
Fixes: 6cc5ca7688 ("drm/i915: rename raw reg access functions")
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326233817.5417-1-daniele.ceraolospurio@intel.com
Tvrtko spotted that I left off the trailing ';'. It went unnoticed by CI
because despite adding the macro, we didn't add a user, so include one as
well (a simple debug print).
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 97ee6e9255 ("drm/i915: stop storing the media fuse")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326180007.11722-1-chris@chris-wilson.co.uk
Since GEM_CREATE is trying to outsmart the user by rounding up unaligned
objects, we used to update the size returned to userspace.
This update seems to have been lost throughout the history.
v2: Use round_up(), reorder locals (Chris)
References: ff72145bad ("drm: dumb scanout create/mmap for intel/radeon (v3)")
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Janusz Krzysztofik <janusz.krzysztofik@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326170218.13255-1-michal.winiarski@intel.com
A few advantages:
- Prepares us for the planned split of display uncore from GT uncore
- Improves our engine-centric view of the world in the engine code
and allows us to avoid jumping back to dev_priv.
- Allows us to wrap accesses to engine register in nice macros that
automatically pick the right mmio base.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-10-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of register access, so
subclass the function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-9-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of register access, so
subclass the function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-8-daniele.ceraolospurio@intel.com
The intel_uncore structure is the owner of FW, so subclass the
function to it.
While at it, use a local uncore var and switch to the new read/write
functions where it makes sense.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-7-daniele.ceraolospurio@intel.com
The full read/write ops can now work on the intel_uncore struct.
Introduce intel_uncore_read/write functions working on intel_uncore
and switch the I915_READ/WRITE macro to internally call those.
v2: no change
v3: add intel_uncore_read/write functions (Chris), update commit msg
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-6-daniele.ceraolospurio@intel.com
Save the HW capabilities to avoid having to jump back to dev_priv
every time.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-4-daniele.ceraolospurio@intel.com
We have several cases where we don't have forcewake (older gens, GVT and
planned display-only uncore), so, instead of checking every time against
the various condition, save the info in a flag and use that.
Note that this patch also change the behavior for gen5 with vpgu
enabled, but this is not an issue since we don't support vgpu on gen5.
v2: split out from previous path, fix check for missing case (Paulo)
v3: Inline helper for clarity in testing flags
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-3-daniele.ceraolospurio@intel.com
They now work on uncore, so use raw_uncore_ prefix. Also move them to
uncore.h
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325214940.23632-2-daniele.ceraolospurio@intel.com
By the time icl_ddi_clock_get() is called we've just got the hw state
from the pll registers. We don't need to read them again: we can rather
reuse what was cached in the dpll_hw_state.
While at it, s/refclk/ref_clock/ just to be consistent with the name
used in code nearby.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-5-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
By the time cnl_ddi_clock_get() is called we've just got the hw state
from the pll registers. We don't need to read them again: we can rather
reuse what was cached in the dpll_hw_state.
This also affects the code for ICL since it partially reuses the CNL
code. However the more intricate part on ICL is left for another patch.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-4-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rename state to pll_state and use it as the argument to
bxt_calc_pll_link(), similar to how it's done in the skl variant.
The WARN_ON(!crtc_state->shared_dpll) is not very useful, so remove it
as well.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-3-lucas.demarchi@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
By the time skl_ddi_clock_get() is called - and thus
skl_calc_wrpll_link() - we've just got the hw state from the pll
registers. We don't need to read them again: we can rather reuse what
was cached in the dpll_hw_state.
v2: rename state variable to pll_state, make argument const in
skl_calc_wrpll_link() and remove not useful warning (from Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322223751.22089-2-lucas.demarchi@intel.com
KMS drivers really should all be able to restore their display state
on resume without fbcon helping out. So make this the default.
Since I'm not entirely foolish, make it only a default, which drivers
can still override. That way when the inevitable regression report
happens I can fix things up with a one-liner plus FIXME comment that
someone should fix up the suspend/resume code in that driver.
But at least all new drivers won't be broken by accident as soon as
you turn off fbcon because "suspend/resume worked when I tested it".
v2: Keep this for radeon because of
commit 18c437caa5
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Tue Nov 14 17:19:29 2017 -0500
Revert "drm/radeon: dont switch vt on suspend"
Thanks to Michel Dänzer for pointing this one out.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: "Michel Dänzer" <michel.daenzer@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Junwei Zhang <Jerry.Zhang@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Shirish S <shirish.s@amd.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Samuel Li <samuel.li@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127173424.301-1-daniel.vetter@ffwll.ch
The live_context() function returns error pointers. It never returns
NULL.
Fixes: 9c1477e83e ("drm/i915/selftests: Exercise adding requests to a full GGTT")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326050843.GA20038@kadam
We're already updating the engine_mask to reflect what's in the HW, so
we can just get the info from there. A couple of macros have been added
to facilitate this.
v2: Appease checkpatch
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322002431.9585-1-daniele.ceraolospurio@intel.com
Iterate over child devices instead of ports in parse_ddi_ports() to
initialize ddi_port_info. We'll eventually need to decide some stuff
based on the child device order, which may be different from the port
order.
As a bonus, this allows better abstractions for e.g. dvo port mapping.
There's a subtle change in the DDC pin and AUX channel sanitization as
we change the order. Otherwise, this should not change behaviour.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322121008.4456-1-jani.nikula@intel.com
UAPI Changes:
- Add Colorspace connector property (Uma)
- fourcc: Several new YUV formats from ARM (Brian & Ayan)
- fourcc: Fix merge conflicts between new formats above and Swati's that
went in via topic/hdr-formats-2019-03-07 branch (Maarten)
Cross-subsystem Changes:
- Typed component support via topic/component-typed-2019-02-11 (Maxime/Daniel)
Core Changes:
- Improve component helper documentation (Daniel)
- Avoid calling drm_dev_unregister() twice on unplugged devices (Noralf)
- Add device managed (devm) drm_device init function (Noralf)
- Graduate TINYDRM_MODE to DRM_SIMPLE_MODE in core (Noralf)
- Move MIPI/DSI rate control params computation into core from i915 (David)
- Add support for shmem backed gem objects (Noralf)
Driver Changes:
- various: Use of_node_name_eq for node name comparisons (Rob Herring)
- sun4i: Add DSI burst mode support (Konstantin)
- panel: Add Ronbo RB070D30 MIPI/DSI panel support (Konstantin)
- virtio: A few prime improvements (Gerd)
- tinydrm: Remove tinydrm_device (Noralf)
- vc4: Add load tracker to driver to detect underflow in atomic check (Boris)
- vboxvideo: Move it out of staging \o/ (Hans)
- v3d: Add support for V3D v4.2 (Eric)
Cc: Konstantin Sudakov <k.sudakov@integrasources.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Ayan Kumar Halder <ayan.halder@arm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlyTxEYACgkQlvcN/ahK
Bwpfhgf9HTwlxHKPwRL70o5Ilp7JVjeLjM5IgDgz+o7F+UZn2OdWocmSDAbJ+lwe
V+LXImc5tykGNRzgn4lXljGv3jqxOgVOxEBo53hVjXeYE/jIdbGDF1cx+1tSke67
lbO61dD9RM5GG9eLuzZ9S72qv5mfBYKHJZuULqOei/Ohnubkg0kDQ3zQEFDah1mh
kqHJkd+x1PwcwBnAjbWdIaCMiwrVmxj7yXLQS8bJzSFKc0/r7HlG8qNWmiBllH0D
aRMO2phHkXCVZY+GWWCEOZwz7ve23sibYm9tzBS69nbWJL12CAomB/8LrRPM2K5v
tVBNrX0eNHMKtOa0En0oF37BXUXizQ==
=DVKQ
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-03-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.2:
UAPI Changes:
- Add Colorspace connector property (Uma)
- fourcc: Several new YUV formats from ARM (Brian & Ayan)
- fourcc: Fix merge conflicts between new formats above and Swati's that
went in via topic/hdr-formats-2019-03-07 branch (Maarten)
Cross-subsystem Changes:
- Typed component support via topic/component-typed-2019-02-11 (Maxime/Daniel)
Core Changes:
- Improve component helper documentation (Daniel)
- Avoid calling drm_dev_unregister() twice on unplugged devices (Noralf)
- Add device managed (devm) drm_device init function (Noralf)
- Graduate TINYDRM_MODE to DRM_SIMPLE_MODE in core (Noralf)
- Move MIPI/DSI rate control params computation into core from i915 (David)
- Add support for shmem backed gem objects (Noralf)
Driver Changes:
- various: Use of_node_name_eq for node name comparisons (Rob Herring)
- sun4i: Add DSI burst mode support (Konstantin)
- panel: Add Ronbo RB070D30 MIPI/DSI panel support (Konstantin)
- virtio: A few prime improvements (Gerd)
- tinydrm: Remove tinydrm_device (Noralf)
- vc4: Add load tracker to driver to detect underflow in atomic check (Boris)
- vboxvideo: Move it out of staging \o/ (Hans)
- v3d: Add support for V3D v4.2 (Eric)
Cc: Konstantin Sudakov <k.sudakov@integrasources.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Ayan Kumar Halder <ayan.halder@arm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321170805.GA50145@art_vandelay
Fixup the errno as we adjusted the error path to receive the errno and
not compute it itself from ERR_PTR(ctx) anymore.
drivers/gpu/drm/i915/i915_gem_context.c:793 i915_gem_context_open() warn: passing a valid pointer to 'PTR_ERR'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3aa9945a52 ("drm/i915: Separate GEM context construction and registration to userspace")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325090413.19906-2-chris@chris-wilson.co.uk
This is the default for atomic drivers.
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221155857.19773-1-daniel.vetter@ffwll.ch
The AGPBUSY thing doesn't work on i945gm anymore. This means
the gmch is incapable of waking the CPU from C3 when an interrupt
is generated. The interrupts just get postponed indefinitely until
something wakes up the CPU. This is rather annoying for vblank
interrupts as we are unable to maintain a steady framerate
unless the machine is sufficiently loaded to stay out of C3.
To combat this let's use pm_qos to prevent C3 whenever vblank
interrupts are enabled. To maintain reasonable amount of powersaving
we will attempt to limit this to C3 only while leaving C1 and C2
enabled.
v2: Use READ_ONCE() (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30364
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322180804.3300-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
If I'm reading the spec right AML 0x87CA is a Y SKU, so it
should be marked as ULX in our old style terminology.
Cc: stable@vger.kernel.org
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: c0c46ca461 ("drm/i915/aml: Add new Amber Lake PCI ID")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322204944.23613-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
- Implement drm_bridge and drm_panel support for omapdrm
- Drop omapdrm's panel-dpi, tfp410 and connector-dvi drivers
- New DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags
- Improvements to tfp410 driver
- OSD070T1718-19TS panel support to simple-panel
- panel-tpo-td028ttec1 backlight support
-----BEGIN PGP SIGNATURE-----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=hS+k
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for 5.2
- Implement drm_bridge and drm_panel support for omapdrm
- Drop omapdrm's panel-dpi, tfp410 and connector-dvi drivers
- New DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags
- Improvements to tfp410 driver
- OSD070T1718-19TS panel support to simple-panel
- panel-tpo-td028ttec1 backlight support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/670dc1ce-feaf-b88e-780f-b99251b88a82@ti.com
Since commit b7137e0cf1 ("drm/i915: Defer enabling rc6 til after we
submit the first batch/context"), intel_suspend_gt_powersave() has been
a no-op. As we still do not need to do anything explicitly on suspend
(we do everything required on idling), remove the defunct function.
References: b7137e0cf1 ("drm/i915: Defer enabling rc6 til after we submit the first batch/context")
Suggested-by: "Hiatt, Don" <don.hiatt@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190323214009.23294-1-chris@chris-wilson.co.uk
GuC may send notification messages with payload larger than
single u32. Prepare driver to accept longer messages.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321120004.53012-1-michal.wajdeczko@intel.com
Initially found issue with closed context debug check when pin
hw_id for GVT context, looks we should always pin hw_id for that
as GVT context is fixed for each vGPU life cycle, and we'd also
like to get pinned hw_id e.g for perf reason, etc.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190311023747.1426-1-zhenyuw@linux.intel.com
EHL uses the same firmware as ICL.
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-6-rodrigo.vivi@intel.com
EHL has a different number of subslices.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-5-rodrigo.vivi@intel.com
Configure the correct set of outputs for EHL. EHL has three DDI's
plus DSI.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-4-rodrigo.vivi@intel.com
Elkhart Lake has a different set of PLLs as compared to Ice Lake,
although programming them is very similar.
v2: Rebase on top of s/icl_pll_funcs/combo_pll_funcs
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-3-rodrigo.vivi@intel.com
Add ElkhartLake as a unique platform as there are some differences
between it and Icelake.
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-2-rodrigo.vivi@intel.com
Add known EHL PCI IDs.
v2 (Rodrigo): Removed x86 early quirk. To be sent in a separated
patch cc'ing the appropriated list and maintainers for
proper ack.
v3: (Rodrigo): - Removed .num_pipes = 3 that is coming since GEN&_FEATURES.
- Added ppgtt type and size after rework from Bob and Chris
v4: (Rodrigo): - remove ppgtt type added on v3. Jose pointed it is not
needed.
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322175847.25707-1-rodrigo.vivi@intel.com
Rename intel_find_panel_downclock() to intel_panel_edid_downclock_mode()
to make it clear it's looking for the downclock mode in the EDID.
And while at it polish the implementation a bit as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Some monitors apparently forget to mark any mode as preferred in the
EDID. In this particular case we have a very generic looking ID
"PNP Model 0 Serial Number 4" / "LVDS 800x600" so a specific quirk
doesn't seem particularly wise. Also the quirk we have
(EDID_QUIRK_FIRST_DETAILED_PREFERRED) is actually defunct so we'd
have to fix it first.
When there is no preferred mode we currently fall back to the VBT.
That approach fails us here as the VBT mode is 1024x768 whereas
the panel resolution is 800x600. So instead of falling back to the
VBT when there is no preferred mode let's just pick the first
probed mode. Only if the EDID provided no modes we fall back to
the VBT.
For this machine the VBIOS would appear to select the 800x600
60Hz EST mode rather than the first detailed mode (which is
the new fallback will pick). The two modes differ only by
having opposite sync polarities, which does not seem to matter
to the panel in question.
v2: Make sure the probed_modes list is not empty
Cc: Adam Jackson <ajax@redhat.com>
Cc: Roberto Viola <cagnulein@gmail.com>
Tested-by: Roberto Viola <cagnulein@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109780
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-2-ville.syrjala@linux.intel.com
Reviewed-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Both LVDS and eDP have the same code to look up the preferred mode
from the connector probed_modes list. Move the code to a common
location.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321132446.22394-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
I added the loop but neglected to actually pass the level to the
function. So we were just looping 8 times calculating the exact
same thing every time.
Fixes: df331de3f8 ("drm/i915: Allocate enough DDB for the cursor")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321175128.32178-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Previously, our view has been always to run the engines independently
within a context. (Multiple engines happened before we had contexts and
timelines, so they always operated independently and that behaviour
persisted into contexts.) However, at the user level the context often
represents a single timeline (e.g. GL contexts) and userspace must
ensure that the individual engines are serialised to present that
ordering to the client (or forgot about this detail entirely and hope no
one notices - a fair ploy if the client can only directly control one
engine themselves ;)
In the next patch, we will want to construct a set of engines that
operate as one, that have a single timeline interwoven between them, to
present a single virtual engine to the user. (They submit to the virtual
engine, then we decide which engine to execute on based.)
To that end, we want to be able to create contexts which have a single
timeline (fence context) shared between all engines, rather than multiple
timelines.
v2: Move the specialised timeline ordering to its own function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-4-chris@chris-wilson.co.uk
It can be useful to have a single ioctl to create a context with all
the initial parameters instead of a series of create + setparam + setparam
ioctls. This extension to create context allows any of the parameters
to be passed in as a linked list to be applied to the newly constructed
context.
v2: Make a local copy of user setparam (Tvrtko)
v3: Use flags to detect availability of extension interface
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-3-chris@chris-wilson.co.uk
In preparation to making the ppGTT binding for a context explicit (to
facilitate reusing the same ppGTT between different contexts), allow the
user to create and destroy named ppGTT.
v2: Replace global barrier for swapping over the ppgtt and tlbs with a
local context barrier (Tvrtko)
v3: serialise with struct_mutex; it's lazy but required dammit
v4: Rewrite igt_ctx_shared_exec to be more different (aimed to be more
similarly, turned out different!)
v5: Fix up test unwind for aliasing-ppgtt (snb)
v6: Tighten language for uapi struct drm_i915_gem_vm_control.
v7: Patch the context image for runtime ppgtt switching!
Testcase: igt/gem_vm_create
Testcase: igt/gem_ctx_param/vm
Testcase: igt/gem_ctx_clone/vm
Testcase: igt/gem_ctx_shared
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-2-chris@chris-wilson.co.uk
An idea for extending uABI inspired by Vulkan's extension chains.
Instead of expanding the data struct for each ioctl every time we need
to add a new feature, define an extension chain instead. As we add
optional interfaces to control the ioctl, we define a new extension
struct that can be linked into the ioctl data only when required by the
user. The key advantage being able to ignore large control structs for
optional interfaces/extensions, while being able to process them in a
consistent manner.
In comparison to other extensible ioctls, the key difference is the
use of a linked chain of extension structs vs an array of tagged
pointers. For example,
struct drm_amdgpu_cs_chunk {
__u32 chunk_id;
__u32 length_dw;
__u64 chunk_data;
};
struct drm_amdgpu_cs_in {
__u32 ctx_id;
__u32 bo_list_handle;
__u32 num_chunks;
__u32 _pad;
__u64 chunks;
};
allows userspace to pass in array of pointers to extension structs, but
must therefore keep constructing that array along side the command stream.
In dynamic situations like that, a linked list is preferred and does not
similar from extra cache line misses as the extension structs themselves
must still be loaded separate to the chunks array.
v2: Apply the tail call optimisation directly to nip the worry of stack
overflow in the bud.
v3: Defend against recursion.
v4: Fixup local types to match new uabi
Opens:
- do we include the result as an out-field in each chain?
struct i915_user_extension {
__u64 next_extension;
__u64 name;
__s32 result;
__u32 mbz; /* reserved for future use */
};
* Undecided, so provision some room for future expansion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322092325.5883-1-chris@chris-wilson.co.uk
Adding a call to intel_uc_suspend in i915_gem_suspend, which
is a common point for the suspend/resume and hibernate paths.
This fixes an unbalanced call that causes issues with the CTB
register/deregister.
v2: Making the call unconditional (Daniele)
Moving the call to after the GEM_BUG_ON (Chris)
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321203804.6845-1-sujaritha.sundaresan@intel.com
32 is too many for the likes of kbl, and in order to insert that many
requests into the ring requires us to declare the first few hung --
understandably a slow and unexpected process. Instead, measure the size
of a singe requests and use that to estimate the upper bound on the
chain length we can use for our test, remembering to flush the previous
chain between tests for safety.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: "Yokoyama, Caz" <caz.yokoyama@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321194031.20240-1-chris@chris-wilson.co.uk
plus a fix off-by-one in our hang report and a protection;
and a fix for eDP panels on Gen9 platforms on VBT absence.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJckpgDAAoJEPpiX2QO6xPKDDgH/i9AQQLbJCX/nXzJUhnKSvu5
xFIFbXt/kd5hkeRVZ/qLW831okdJdVq8GW/C4AAfEMNbnhhhAI1/PRuO7lrHKuU6
QAOKvJrNKkdRxNrkHArIKXTdfjr4UnXOgQFSgFQNRLFmOi9/czoeWG0/kGkvp+WT
6HV7o1Zgghqs9SUOtmA9TZ/znq1neLlwJRuePep1TY4vbJoWnZ0ekn/MqUPDWpg2
W5stfS7AyuMX1CWJnr91G6NEqaU8Bm9aC1WmBqvdPPkVYWIJNDGWLjOEDpqzdoi4
D17RntvZ685mer+GM6fMICY09lC9vuYomT3gdRy4ZLz24VmMSyZJ7juJoYYGa7Y=
=gHfL
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2019-03-20' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
A protection on our mmap against attempts to map past the end of the object;
plus a fix off-by-one in our hang report and a protection;
and a fix for eDP panels on Gen9 platforms on VBT absence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320201451.GA7993@intel.com
Empty chunk do not have a bo associated with them so no need to pin/unpin
on suspend/resume.
This fix suspend/resume on 5.1rc1 when NOUVEAU_SVM is enabled.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Tested-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
pm_runtime_get_sync returns negative on failure.
Fixes: eaeb9010bb ("drm/nouveau/debugfs: Wake up GPU before doing any reclocking")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The hmm_devmem_add() function doesn't return NULL, it returns error
pointers.
Fixes: 5be73b6908 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/nouveau/nouveau_dmem.c: In function 'nouveau_dmem_free':
drivers/gpu/drm/nouveau/nouveau_dmem.c:103:22: warning:
variable 'drm' set but not used [-Wunused-but-set-variable]
struct nouveau_drm *drm;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We already unlocked a few lines earlier so this code unlocks twice on
the success path.
Fixes: 289921b03f ("drm/amd/powerplay: implement sysfs of pp_table for smu11 (v2)")
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The > should be >= so that we don't read one element beyond the end of
the vega20_message_map[] array.
Fixes: 78031c2c4d ("drm/amd/powerplay: implement smu vega20_message_map for vega20")
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "size" variable is unsigned. We never pass invalid sizes to this
function and we already used it as an array offset earlier so it's
too late to check here.
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leads to an undefined symbol otherwise.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9b638f9751.
Adding this to the mapping is complete nonsense and the whole
implementation looks racy. This patch wasn't thoughtfully reviewed
and should be reverted for now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Liu, Shaoyun <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And remove the existing code when it is unused.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And remove the existing code when it is unused.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate out all functions for SDMA and CPU based page table
updates into separate backends.
This way we can keep most of the complexity of those from the
core VM code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allocating 16KB was way to much, just use 2KB as a start for now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the update parameter into the VM header and rename them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean that up a bit and allow to always have the DMA addresses around.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not needed any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we are already in the desired write domain of a set-domain ioctl,
then there is nothing for us to do and we can quickly return back to
userspace, avoiding any lock contention. By recognising that the
write_domain is always a subset of the read_domains, and excluding the
no-op case of requiring 0 read_domains in the ioctl, we can infer if the
current write_domain matches the target read_domains, there is nothing
for us to do.
Secondary aspect of this is that we undo the arbitrary fetching and
potential flushing of all pages for a set-domain(.write=CPU) call on a
fresh object -- which was introduced simply because we do the get-pages
before taking the struct_mutex.
References: 40e62d5d6b ("drm/i915: Acquire the backing storage outside of struct_mutex in set-domain")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321161908.8007-2-chris@chris-wilson.co.uk
When we return pages to the system, we ensure that they are marked as
being in the CPU domain since any external access is uncontrolled and we
must assume the worst. This means that we need to always flush the pages
on acquisition if we need to use them on the GPU, and from the beginning
have used set-domain. Set-domain is overkill for the purpose as it is a
general synchronisation barrier, but our intent is to only flush the
pages being swapped in. If we move that flush into the pages acquisition
phase, we know then that when we have obj->mm.pages, they are coherent
with the GPU and need only maintain that status without resorting to
heavy handed use of set-domain.
The principle knock-on effect for userspace is through mmap-gtt
pagefaulting. Our uAPI has always implied that the GTT mmap was async
(especially as when any pagefault occurs is unpredicatable to userspace)
and so userspace had to apply explicit domain control itself
(set-domain). However, swapping is transparent to the kernel, and so on
first fault we need to acquire the pages and make them coherent for
access through the GTT. Our use of set-domain here leaks into the uABI
that the first pagefault was synchronous. This is unintentional and
baring a few igt should be unoticed, nevertheless we bump the uABI
version for mmap-gtt to reflect the change in behaviour.
Another implication of the change is that gem_create() is presumed to
create an object that is coherent with the CPU and is in the CPU write
domain, so a set-domain(CPU) following a gem_create() would be a minor
operation that merely checked whether we could allocate all pages for
the object. On applying this change, a set-domain(CPU) causes a clflush
as we acquire the pages. This will have a small impact on mesa as we move
the clflush here on !llc from execbuf time to create, but that should
have minimal performance impact as the same clflush exists but is now
done early and because of the clflush issue, userspace recycles bo and
so should resist allocating fresh objects.
Internally, the presumption that objects are created in the CPU
write-domain and remain so through writes to obj->mm.mapping is more
prevalent than I expected; but easy enough to catch and apply a manual
flush.
For the future, we should push the page flush from the central
set_pages() into the callers so that we can more finely control when it
is applied, but for now doing it one location is easier to validate, at
the cost of sometimes flushing when there is no need.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321161908.8007-1-chris@chris-wilson.co.uk
The timeline->name is only used for convenience in pretty printing the
i915_request.fence->ops->get_timeline_name() and it is just as
convenient to pull it from the gem_context directly. The few instances
of its use inside GEM_TRACE() has proven more of a nuisance than
helpful, so not worth saving imo.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321140711.11190-4-chris@chris-wilson.co.uk
Define a mutex for the exclusive use of interacting with the per-file
context-idr, that was previously guarded by struct_mutex. This allows us
to reduce the coverage of struct_mutex, with a view to removing the last
bits coordinating GEM context later. (In the short term, we avoid taking
struct_mutex while using the extended constructor functions, preventing
some nasty recursion.)
v2: s/context_lock/context_idr_lock/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321140711.11190-2-chris@chris-wilson.co.uk
In later patches, it became apparent that userspace can see a partially
constructed GEM context and begin using it before it was ready, to much
hilarity. Close this window of opportunity by lifting the registration of
the context with userspace (the insertion of the context into the filp's
idr) to the very end of the CONTEXT_CREATE ioctl.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321140711.11190-1-chris@chris-wilson.co.uk
The mock_context() function returns NULL on error, it doesn't return
error pointers.
Fixes: 85fddf0b00 ("drm/i915: Introduce a context barrier callback")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321092451.GK2202@kadam
D71 consists of a number of Register Blocks, every Block controls a
specific HW function, every block has a common block_header to represent
its type and pipeline information.
GCU (Global Control Unit) is the first Block which describe the global
information of D71 HW, Like number of block contained and the number of
pipeline supported.
So the d71_enum_resources parsed GCU and create pipeline according
the GCU configuration, and then iterate and detect the blocks that
indicated by the GCU and block_header.
And this change also added two struct d71_dev/d71_pipeline to extend
komeda_dev/komeda_pipeline to add some d71 only members.
v2:
- Return the specific errno not -1.
- Use DRM_DEBUG as default debug msg printer.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
gcc-4.8 and older dislike the use of __builtin_constant_p() within a
constant expression context, and so we must use the magical
__is_constexpr() instead.
For example, with gcc-4.8.5:
../drivers/gpu/drm/i915/i915_reg.h:167:27: error: first argument to ‘__builtin_choose_expr’ not a constant
../include/linux/build_bug.h:16:45: error: bit-field ‘<anonymous>’ width not an integer constant
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Uma Shankar <uma.shankar@intel.com>
Fixes: baa09e7d2f ("drm/i915: use REG_FIELD_PREP() to define register bitfield values")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320154021.5244-1-chris@chris-wilson.co.uk
There has unfortunately been a conflict with the following 3 commits:
commit e9961ab95a
Author: Ayan Kumar Halder <ayan.halder@arm.com>
Date: Fri Nov 9 17:21:12 2018 +0000
drm: Added a new format DRM_FORMAT_XVYU2101010
commit 7ba0fee247
Author: Brian Starkey <brian.starkey@arm.com>
Date: Fri Oct 5 10:27:00 2018 +0100
drm/fourcc: Add AFBC yuv fourccs for Mali
and
commit 50bf5d7d59
Author: Swati Sharma <swati2.sharma@intel.com>
Date: Mon Mar 4 17:26:33 2019 +0530
drm: Add Y2xx and Y4xx (xx:10/12/16) format definitions and fourcc
Unfortunately gcc didn't warn about the redefinitions, because the
double defines were the set to same value, and gcc apparently no longer
warns about that.
Fix this by using new XYVU for i915, without alpha, and making the
Y41x definitions match msdn, with alpha.
Fortunately we caught it early, and the conflict hasn't even landed in
drm-next yet.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Ayan Kumar Halder <ayan.halder@arm.com>
Cc: malidp@foss.arm.com
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319121702.6814-1-maarten.lankhorst@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com> #irc
Acked-by: Sean Paul <sean@poorly.run>
Reviewed-by: Ayan Kumar halder <ayan.halder@arm.com>
RLC #53815 ucode has the noise issue on 4k playback while gfxoff enabled.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables gfxoff and stutter mode again, since we take more testing on
raven series. For raven2 and picasso, we can enable it directly. And for raven,
we need check the RLC/SMC ucode version cannot be less than #531/0x1e45.
v2: add smc version checking for raven.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Tested-by: Likun Gao <Likun.Gao@amd.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in pr_warn message; fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/gpu/drm/amd/amdgpu/../powerplay/vega20_ppt.c:456:2: warning:
variable 'num_of_levels' is used uninitialized whenever '?:' condition
is false [-Wsometimes-uninitialized]
smu_read_smc_arg(smu, &num_of_levels);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../powerplay/inc/amdgpu_smu.h:608:3: note:
expanded from macro 'smu_read_smc_arg'
((smu)->funcs->read_smc_arg? (smu)->funcs->read_smc_arg((smu), (arg)) : 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../powerplay/vega20_ppt.c:457:7: note:
uninitialized use occurs here
if (!num_of_levels) {
^~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../powerplay/vega20_ppt.c:456:2: note: remove
the '?:' if its condition is always true
smu_read_smc_arg(smu, &num_of_levels);
^
drivers/gpu/drm/amd/amdgpu/../powerplay/inc/amdgpu_smu.h:608:3: note:
expanded from macro 'smu_read_smc_arg'
((smu)->funcs->read_smc_arg? (smu)->funcs->read_smc_arg((smu), (arg)) : 0)
^
drivers/gpu/drm/amd/amdgpu/../powerplay/vega20_ppt.c:446:27: note:
initialize the variable 'num_of_levels' to silence this warning
uint32_t i, num_of_levels, clk;
^
= 0
1 warning generated.
The if statement it mentions as potentially problematic is currently
always true because the read_smc_arg callback is assigned at the
bottom of this file but Clang can't tell that. If the callback were
ever to disappear, num_of_levels would never be initialized. Just
zero initialize it to ensure that the intent behind this code
remains the same.
Link: https://github.com/ClangBuiltLinux/linux/issues/425
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_move_vram_ram':
drivers/gpu/drm/radeon/radeon_ttm.c:254:24: warning:
variable 'rdev' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_move_ram_vram':
drivers/gpu/drm/radeon/radeon_ttm.c:301:24: warning:
variable 'rdev' set but not used [-Wunused-but-set-variable]
It's not used since a987fcaa80 ("ttm: Make parts of a struct ttm_bo_device
global.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want DRM planes to be initialized in the following order:
- primary planes
- overlay planes
- cursor planes
to support existing userspace expectations for plane z-ordering. This
means that we also need to register CRTCs after all planes have been
initialized since overlay planes can be placed on any CRTC.
So the only reason why we have the mode_info->planes list is to
remember the primary planes for use later when we need to register
the CRTC.
Overlay planes have no purpose being in this list. DRM will cleanup
any planes that we've registered for us, so the only planes that need to
be explicitly cleaned up are the ones that have failed to register.
By dropping the explicit free on every plane in the mode_info->planes
list this patch also fixes a double-free in the case where we fail to
initialize only some of the planes.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need arbitrary read/write over DP AUX DPCD
for debugging
[How]
Three debugfs entries
Set the target address by writing to
"aux_dpcd_address"
(The first four bytes written are used)
Set the transaction size in bytes by writing to
"aux_dpcd_size"
(The first four bytes written are used)
Start a transaction by reading/writing
"aux_dpcd_data"
Do note: there is no concerrency protection at all
Accessing these entries in quick succession can lead
to strange behaviour
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add sdp_message debugfs entry in amdgpu.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add a DM accessible SDP interface for custom data.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are issues removing surfaces/streams when odm is active.
This is a step to fix that
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of places opp programming was missing for odm second pipe.
This change fixes the oversight.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We fail to reset the second odm combine pipe. This change fixes
odm pointer management.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Releasing planes should not release the 2nd odm pipe right away,
this change leaves us with 2 pipes with null planes and same stream
when planes are released during odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refactor setting bit fields. Correcting the offset of MD0.
Initializing the InfoPacket header fields. Defining the field offsets
and masks.
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain cases we do link training when we don't have a backend.
[How]
In dc_link_set_preferred_link_settings(), store preferred link settings
first and then verify that the link is DP and the link stream's backend is
enabled. If either is false, then we will not do any link retraining.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add these interfacese for future use
setup_global_lock()
lock_global()
pipe_control_lock_global()
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we are missing a few checks to see if HDR10 is allowed.
In particular we never check for the extended colorimetry bit (whether its
present or set to 1). Further we don't read in the dpcd block in DC that
would provide these bits.
[How]
- Added in DC code to read in the block containing the extended colorimetry
bit.
Signed-off-by: Harmanprit Tatla <Harmanprit.Tatla@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Somewhere in the atomic check reshuffle ABM got lost.
ABM is a crtc property (copied from a connector property).
It can change without a modeset, just like underscan.
[How]
In the skip_modeset branch of atomic check crtc updates,
copy over the abm property.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HDMI plugfest, MTK report our EMP with VRR_EN bit = 0.
VRR_EN bit is EMP-MD0-bit 0. Currently driver set 1 to bit 3.
[How]
Programming correct VRR_EN bit in EMP-MD0-bit0.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There exist displays with EDIDs > 512 bytes, existing code
will cause us to ignore all extension blocks.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Audio was unmuted for HDMI only, need to do so for DP as well.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering is observed on some displays when the number of inserted BTR
frames changes frequently.
[How]
Add in a margin of drift to prevent the inserted number of frames from
jumping around too frequently.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
when programming VID_TIMING, we were using the original VESA timing for DP_VIDM/N.
for YCbCr420 or compressed YCbCr422, using half rate as YCbCr444.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to set VID_N_MUL for 4:2:0 cases
[How]
Move setting to enc1_stream_encoder_dp_unblank and
ensure it is also set for non-4:2:0 cases.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move out of header to dc_helper.c, in preparation for future
implementations.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help prevent plane state not being set to the correct default
value if any new properties are added in the future.
[How]
Use the drm helper - which seems to be the common solution among other
DRM drivers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we were only checking the return value in one place, thus changing
generic_reg_wait from int to void and reading the register instead of
getting it from generic_reg_wait, when we need the return value.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To aid recoverable page faults.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the first paging queue to handle page faults.
v2: handle any number of SDMA instances gracefully
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have re-reoute faults to the other IH
ring we can enable retries again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect hardcoded assumptions are made regarding luma and chroma
alignment. The actual values set for the DRM framebuffer should be used
when programming the address.
[How]
Respect the given pitch for both luma and chroma planes - it's not like
we can force the alignment to anything else at this point anyway.
Use the FB offset for the chroma planes directly. DRM already
provides this to us so there's no need to calculate it manually.
While we don't actually use the chroma surface size parameters on Raven,
these should have technically been fb->width / 2 and fb->height / 2
since the chroma plane is half size of the luma plane for NV12.
Leave a TODO indicating that those should be set based on the actual
surface format instead since this is only correct for YUV420 formats.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When page table are updated by the CPU, synchronize with the
allocation and initialization of newly allocated page tables.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If using old kernel config file, CONFIG_ZONE_DEVICE is not selected,
so CONFIG_HMM and CONFIG_HMM_MIRROR is not enabled, the current driver
error message "Failed to register MMU notifier" is not clear. Inform
user with more descriptive message on how to fix the missing kernel
config option.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109808
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This allows us to ditch i915 in some more places.
v2: use local var in check_vgpu (Paulo)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-9-daniele.ceraolospurio@intel.com
This will allow futher simplifications in the uncore handling.
v2: move register access setup under uncore (Chris)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-8-daniele.ceraolospurio@intel.com
Move the init, fini, prune, suspend, resume function to work on
intel_uncore instead of dev_priv.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-5-daniele.ceraolospurio@intel.com
Now that the internal code all works on intel_uncore, flip the
external-facing interface.
v2: fix GVT.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-4-daniele.ceraolospurio@intel.com
Get/put functions used outside of uncore.c are updated in the next
patch for a nicer split.
v2: use dev_priv where we still have it (Paulo)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319183543.13679-3-daniele.ceraolospurio@intel.com
Upper bits are reserved on gen6, so no issue if we write them. Note that
we're already doing this in the non-MT case of IVB, which uses the same
register.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320122732.14512-1-chris@chris-wilson.co.uk
This patch fixes the PORT_SYNC_MODE_MASTER_SELECT macro
to correctly do the left shifting to set the port sync
master select correctly.
I have tested this fix on ICL.
Fixes: 49edbd4978 ("drm/i915/icl: Define TRANS_DDI_FUNC_CTL DSI registers")
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319221847.21311-1-manasi.d.navare@intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190304092908.57382-2-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190304092908.57382-1-andriy.shevchenko@linux.intel.com
skl_update_pipe_wm() is quite pointless now. Just inline it into
skl_compute_wm().
v2: s/skl_build_pipe_wm/skl_update_pipe_wm/ in the commit message (Matt)
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-10-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Clean up skl_allocate_pipe_ddb() a bit by moving the 'wm' variable
to tighter scope. We'll also consitify it where appropriate.
Also initialize plane_alloc/uv_plane_alloc when decrlaring them
rather than later.
v2: Update commit message (Matt)
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-8-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Currently we disable all the watermarks above the selected max
level for every plane. That would mean that the cursor's watermarks
may also get modified when another plane causes the selected
max watermark level to change. That is not so great as we would
like to keep the cursor as indepenedent as possible to avoid
having to throttle it in resposne to other plane activity.
To avoid that let's keep the watermarks enabled even for levels
above the max selected watermark level, iff the plane has enough
ddb for that particular level. This way the cursor's enabled
watermarks only depend on the cursor itself. This is safe because
the hardware will never choose to use a watermark level unless
all enabled planes have also enabled that level.
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-7-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
We use a fixed ddb allocation for the cursor. Now the calculation
actually makes sure we have enough ddb space, but let's double check
anyway.
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Currently we just assume that 32 or 8 blocks of ddb is sufficient
for the cursor. The 32 might be, but the 8 is certainly not. The
minimum we need is at least what level 0 watermarks need, but that
is a bit restrictive, so instead let's calculate what level 7
would need for a 256x256 cursor. We'll use that to determine the
fixed ddb allocation for the cursor. This way the cursor will never
be responsible for missing out on deeper power saving states.
v2: Loop to make sure this works even if some wm levels are
totally disabled (latency==0)
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190319160311.23529-1-ville.syrjala@linux.intel.com
Extract the meat of skl_compute_plane_wm_params() into a lower
level helper that doesn't depend on the plane state. We'll
reuse this for the cursor ddb allocation calculations.
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-4-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
skl_compute_plane_wm() doesn't actually need the plane state. While
it would make logically sense to pass it, we shall need to reuse
skl_compute_plane_wm() to compute the minimum ddb allocation for
the cursor before the cursor may be enabled. Thus we can't rely
on the plane state. The alternative would be to duplicate a lot of
the wm calculations for the cursor ddb allocation case, which doens't
appeal to me.
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
If the minimum required ddb space for all the planes equals the
total ddb space available we are allowed to use the relevant
watermark level.
Cc: Neel Desai <neel.desai@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205844.6339-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
To allow unsetting .is_mobile for the desktop variant
of PNV fix up the cdclk code to select the mobile HPLLVCO register
for both PNV variants.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318165633.28924-5-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We want to allow the desktop PNV to not have .is_mobile set. To
that end let's add a small helper to determine if the platform
has the ASLE interrupt (or equivalent). Supposdely both PNV
variants have it.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318165633.28924-4-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Add a small helper to determine if we have the panel power
sequencer or not. We'll make PNV an exceptional case so
that we can unset .is_mobile for the desktop variant.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318165633.28924-3-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Make the code self-documenting by introducing i9xx_has_pfit().
Also make PNV an exceptional case so that we can unset
.is_mobile for the desktop variant.
v2: s/gen4/gen>=4/ (Tvrtko)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190319142329.22881-1-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
g33/i964g/g45 are the exceptional cases when it comes to
the swizzle detection. Let's reorder the code to handle
them first and let everything else be handled by the
else branch. This allows us to unset .is_mobile for the
desktop PNV variant (which supposedly must follow the
"mobile" path here).
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318165633.28924-1-ville.syrjala@linux.intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Exercise acquiring and releasing forcewake around register reads. In
order to read a register behind a GT powerwell, we need to instruct that
powerwell to wake up using a forcewake. When we no longer require the GT
powerwell, we tell the GT to release our forcewake. Inside the
forcewake, the register read should work but outside it should just
return garbage, 0 being the most common garbage. Thus we can detect when
we are inside and outside of the forcewake with just a simple register
read, and so can verify that the GT powerwell is released when we say
so.
v2: Picking the right forcewaked register to return 0 outside of
forcewake is an art.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320080052.27273-1-chris@chris-wilson.co.uk
Now that the DMC register range is no longer in the bindings, remove any
mention towards it and exclusively use the meson-canvas module.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190311105144.7276-3-mjourdan@baylibre.com
When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.
Cc: <stable@vger.kernel.org>
Fixes: a278724aa2 ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.
v2: Test for id != -ENOMEM instead of id == -ENOSPC.
Cc: <stable@vger.kernel.org>
Fixes: 4eb085e42f ("drm/vmwgfx: Convert to new IDA API")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Comet Lake is a Intel Processor containing Gen9
Intel HD Graphics. This patch adds the initial set of
PCI IDs. Comet Lake comes off of Coffee Lake - adding
the IDs to Coffee Lake ID list.
More support and features will be in the patches that follow.
v2: Split IDs according to GT. (Rodrigo)
v3: Update IDs.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318200133.9666-1-anusha.srivatsa@intel.com
userptr may cross two VMAs if the forked child process (not call exec
after fork) malloc buffer, then free it, and then malloc larger size
buf, kerenl will create new VMA adjacent to old VMA which was cloned
from parent process, some pages of userptr are in the first VMA, the
rest pages are in the second VMA.
HMM expects range only have one VMA, loop over all VMAs in the address
range, create multiple ranges to handle this case. See
is_mergeable_anon_vma in mm/mmap.c for details.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Userptr restore may have concurrent userptr invalidation after
hmm_vma_fault adds the range to the hmm->ranges list, needs call
hmm_vma_range_done to remove the range from hmm->ranges list first,
then reschedule the restore worker. Otherwise hmm_vma_fault will add
same range to the list, this will cause loop in the list because
range->next point to range itself.
Add function untrack_invalid_user_pages to reduce code duplication.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we won't be able to cleanly handle page faults.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that not only the entities are flush, but that
we also wait for the HW to finish all processing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's a bug having a dead pointer in the IDR, silently returning
is the worst we can do.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the chash implementation for now since it isn't used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Further testing showed that the idea with the chash doesn't work as expected.
Especially we can't predict when we can remove the entries from the hash again.
So replace the chash with a ring buffer/hash mix where entries in the container
age automatically based on their timestamp.
v2: use ring buffer / hash mix
v3: check the timeout to make sure all entries age
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only process a maximum of 32 IVs before writing back the RPTR. This improves
hw handling when we get close to an overflow in the ring buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That doesn't seem to have any negative effects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The doorbells should already be reserved, just enable them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable overflow and enable full drain. This makes fault handling on ring 1
much more reliable since we don't generate back pressure any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The buffers should be cleared when possible but we also don't want
buffer creation to fail in the rare case where the ring isn't ready
during the call. This could happen during some suspend/resume sequences.
Cc: Christian König <ckoenig.leichtzumerken@gmail.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dumb_create API isn't intended for high performance rendering
and it's more useful for userspace (ie. IGT) to have them precleared.
The bonus here is that we also won't needlessly leak whatever was
previously in VRAM, but it also probably wasn't sensitive if it was
going through this API.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add ras post init function.
Do some initialization after all IP have finished their late init.
Add new member flags which will control the ras work flow.
For now, vbios enable ras for us on boot. That might change in the
future.
So there should be a flag from vbios to tell us if ras is enabled or not
on boot. Looks like there is no such info now.
Other bits of the flags are reserved to control other parts of ras.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add drm info output if ras initialized successfully.
add ras atomfirmware sanity check.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
lockdep need a static key.
Previously we set ignore bit to avoid the warning.
Now call sysfs_attr_init to initialize the static key.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-and-Tested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unzero char is accepted by sscanf, so when data is structure but
unexpectedly return error invalid;
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, it is not clear how ras is supported. Both software and
hardware can set the supported. That is confusing.
Fix it by adding new member hw_supported.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set ignore bit to satisfy locpdep.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ta is optional, so check if ta firmware is loaded or not.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The descriptions of modinfo wrongly show two parameters
for each feature(see below). This patch can fix this
incorrect outputs.
parm: amdgpu_ras_enable:Enable RAS features on the GPU (0 = disable, 1 = enable, -1 = auto (default))
parm: ras_enable:int
parm: amdgpu_ras_mask:Mask of RAS features to enable (default 0xffffffff), only valid when ras_enable == 1
parm: ras_mask:uint
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sram ecc capability could be get from firmware_capability field in firmwareinfo table
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ecc default status (enabled or disabled) could be get from umc_config field in umc_info table
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new umc_info structures and new firmware_capability defines
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Suspend will put irq, so resume need get irq back.
And in the same time, skip other ras initialization.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RAS ECC event will combine with GPU reset event, due to
ECC interrupts are caused by uncorrectable error that triggers
GPU reset.
v2: Fix misleading-indentation warning
v3: fix build with CONFIG_HSA_AMD disabled
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is to collaborate with HSA_CAPABILITY in libhsakmt.
v2: squash in NULL pointer check
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, the debugfs control node can't parse bash-like commands.
Now add such support for any tester that uses scripts.
v2: squash in fixes for input validation
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gpu reset is not stable on vega20 A1.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a query for userspace to check which RAS features
are enabled.
v2: squash in warning fix
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add AMDGPU_CTX_QUERY2_FLAGS_RAS_CE/UE which indicate if any error happened
between previous query and this query.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Register ecc interrupts and ecc interrupt handler on gfx9.
Add ras support on gfx9
v2: squash in warning fix
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
register IH, enable ras features on sdma.
create sysfs debugfs file for sdma.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark vram pages with errors as bad and prevent the driver
from using them.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add obj management.
add feature control.
add debugfs infrastructure.
add sysfs infrastructure.
add IH infrastructure.
add recovery infrastructure.
It is a framework. Other IPs need call amdgpu_ras_xxx function instead of
psp_ras_xxx functions.
v2: squash in warning fixes
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add trigger_error and cure_posion.
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Define the driver side interface for ras ta.
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Output the ta fw, aka xgmi/ras, via debugfs.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add ras fw part, xgmi and ras fw are combined together in ta binary.
Reading the data from the info is not implemented yet.
v2: squash in "drm/amdgpu: fix NULL pointer when ta is missing"
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
each asic may be has different smc if version,
so move its to asic file to implement.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
simplify macro of MSG_MAP for sw-smu
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use function parameter mc as the second parameter of amdgpu_gmc_vram_location,
so codes look more consistent.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For new DC planes the correct plane address fields are filled based
on whether the plane had a graphics or video format.
However, when we perform stream and plane updates using DC we only ever
fill in the graphics format fields. This causing corruption and hangs
when using video surface formats like NV12 for planes.
[How]
Use the same logic everywhere we update dc_plane_address - always
fill in the correct fields based on the surface format type.
There are 3 places this is done:
- Atomic check, during DC plane creation
- Atomic commit, during plane prepare_fb
- Atomic commit tail, during amdgpu_dm_commit_planes
We use the fill_plane_tiling_attributes in all 3 locations and it
already needs the address to update DCC attributes, so the surface
address update logic can be moved into this helper.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
Using SDMA for TLB invalidation in certain ASICs exposed a problem
of IB pool not being ready while SDMA already up on Init and already
shutt down while SDMA still running on Fini. This caused
IB allocation failure. Temproary fix was commited into a
bringup branch but this is the generic fix.
Fix:
Init IB pool rigth after GMC is ready but before SDMA is ready.
Do th opposite for Fini.
v2: Remove restriction on SDMA early init and move amdgpu_ib_pool_fini
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor updates must acquire the pipe control lock to
prevent vupdate from triggering in the middle of cursor
programming. On DCN1 the pipe control lock prevents
pageflips from occurring. This means that a cursor update
right before vupdate can delay a pending pageflip
[How]
If the time until the next vupdate is less than a
conservative estimate of the cursor programming time,
wait until the vupdate has passed before locking.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We will not retry when EDID read failure using i2c over aux
[how]
treat i2c over aux failure the same as defer
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
"reference clock" is a very overloaded variable in DC and causes confusion
as there are multiple sources of reference clock, which may be different values
incorrect input values to DML will cause DCHUB to be programmed improperly
and lead to hard to debug underflow issues
[how]
instead of using ref clock everywhere, specify WHICH ref clock:
- xtalin
- dccg refclk
- dchub refclk
these are all distinct values which may not be equal
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DRM overlay planes DM exposes support RGBA formats but are currently
forced as fully opaque over whatever they overlay.
[How]
Expose DRM blending mode and alpha properties to userspace.
The overlays exposed support per-pixel pre-multiplied alpha along with
global plane opacity.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maarten Lankhorst