This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).
A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.
Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.
v2: use pipe_config for storing pfit values (Daniel)
add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
lvds pairs (which makes sense, since it only supports 8bpc pipe
outpu configurations).
- hsw doesn't support lvds.
v2: Remove redudant dither setting.
v3: Completly drop reliance on dev_priv->lvds_dither.
v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.
v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.
v6: Actually git add.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation of adding locking to backlight, make max backlight value
(the modulation frequency the PWM duty cycle value must not exceed)
internal to intel_panel.c.
Have intel_panel_set_backlight() accept a caller defined range for level,
and scale input to max backlight value internally.
Clean up intel_panel_get_max_backlight() and usage internally.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows unifying a bunch of the PLL calculations and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Valleyview voltage swing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric. Update
vlv_update_pll, i9xx_crtc_enable, and intel_enable_pll with the
appropriate programming.
We need to make sure that the tx lane reset occurs in both the full mode
set and DPMS paths, so factor things out to allow that.
v2: use different DPIO_DIVISOR values for VGA and DisplayPort
v3: Fix update pll logic to use same DPIO_DIVISOR & DPIO_REFSFR values
for all display interfaces
v4: collapse with various updates
v5: squash with crtc enable/pll enable bits
v6: split out DP code (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
remove unneeded check in 9xx pll div update (Jani)
wrap VLV pll update call in IS_VALLEYVIEW (Jani)
move port enable back to end of crtc enable (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
v7: fix up conflicts against latest drm-intel-next-queued
v8: use DPIO reg names, fix pipes (Jani)
from mPhy_registers_VLV2_ww20p5 doc
v9: update to latest info from driver enabling notes doc
driver_vbios_notes_9
v10: fixup a bit of pipe/port confusion to allow eDP and HDMI to work
simultaneously (Jesse)
v11: use pll/port callbacks for DPIO port activity (Daniel)
use separate VLV CRTC enable function (Daniel)
move around port ready checks (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop pfit changes and add a little comment explaining that
vlv has a different enable sequence and so needs it's own crtc_enable
callback. Also apply a fixup patch from Wu Fengguang to shut up some
compiler warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program few Tx buffer Swing control settings through DPIO.
v2: fix up codingstyle (Daniel)
call from set_signal_levels (Ville, Daniel)
use proper port numbers (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2 changes)
[danvet: Reorder if-ladder to avoid two IS_VLV checks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock computations and handling are highly encoder specific, both in
the optimal clock selection and also in which clocks to use and when
sharing of clocks is possible.
So the best place to do this is somewhere in the encoders, with a
generic fallback for those encoders without special needs. To facility
this, add a pipe_config->clocks_set boolean.
This patch here is only prep work, it simply sets the computed clock
values in pipe_config->dpll, and uses that data in the hw clock
setting functions.
Haswell code isn't touched, simply because Haswell clocks work much
different and need their own infrastructure (with probably a
Haswell-specific config->ddi_clock substruct).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse Barnes noticed in his review of my DP cleanup series that
intel_edp_target_clock is now unused. Checking related code I've
noticed that also intel_edp_link_config is long unused.
Kill them both.
Wrt leaky eDP functions used in the common crtc code, the only thing
still left is intel_encoder_is_pch_edp. That one is just due to the
massive confusion between eDP vs. DP and port A vs. port D. Crtc code
should at most concern itself with the later, never with the former.
But that's material for another patch series.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need it in the fdi m_n computation, which nicely kills almost
all ugly special cases in there.
It looks like we also need this to handle 12bpc hdmi correctly.
Eventually it might be better to switch things around and put the
target clock into adjusted_mode->clock and create a new pipe_config
parameter for the port link clock.
v2: Add a massive comment in the code to explain this mess.
v3: s/dp_target_clock/pixel_target_clock in anticipation of the hdmi
use-case.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a flag to designate dp encoders and the dp link m_n parameters
in the pipe config for that. And now that the pipe bpp computations
have been moved up and stored in the pipe config, too, we can do this
without losing our sanity.
v2: Rebased on top of Takashi Iwai's fix to (again) fix the target
clock handling for eDP. Luckily the new code is sane enough and just
does the right thing!
v3: Move ->has_dp_encoder to this patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a rather decent confusion going on around transcoder m_n
values. So let's clarify:
- All dp encoders need this, either on the pch transcoder if it's a
pch port, or on the cpu transcoder/pipe if it's a cpu port.
- fdi links need to have the right m_n values for the fdi link set in
the cpu transcoder.
To handle the pch vs transcoder stuff a bit better, extract transcoder
set_m_n helpers. To make them simpler, set intel_crtc->cpu_transcoder
als in ironlake_crtc_mode_set, so that gen5+ (where the cpu m_n
registers are all at the same offset) can use it.
Haswell modeset is decently confused about dp vs. edp vs. fdi. dp vs.
edp works exactly the same as dp (since there's no pch dp any more),
so use that as a check. And only set up the fdi m_n values if we
really have a pch encoder present (which means we have a VGA encoder).
On ilk+ we've called ironlake_set_m_n both for cpu_edp and for pch
encoders. Now that dp_set_m_n handles all dp links (thanks to the
pch encoder check), we can ditch the cpu_edp stuff from the
fdi_set_m_n function.
Since the dp_m_n values are not readily available, we need to
carefully coax the edp values out of the encoder. Hence we can't (yet)
kill this superflous complexity.
v2: Rebase on top of the ivb fdi B/C check patch - we need to properly
clear intel_crtc->fdi_lane, otherwise those checks will misfire.
v3: Rebased on top of a s/IS_HASWELL/HAS_DDI/ patch from Paulo Zanoni.
v4: Drop the addition of has_dp_encoder, it's in the wrong patch (Jesse).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Thomas Gleixner spotted, it's rather horrible racy:
- We can miss almost a full tick, so need to compensate by 1 jiffy.
- We need to re-check the condition when having timed-out, since a
the last check could have been before the timeout expired. E.g. when
we've been preempted or a long irq happened.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Jack Winter <jbh@alchemy.lu>
Cc: Jack Winter <jbh@alchemy.lu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit bcf9dcc1e6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jul 15 09:42:38 2012 +0100
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
and
commit 0cc2764cc4
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Sat Sep 1 22:59:48 2012 -0700
drm/i915: use cpu_relax() in wait_for_atomic
these two macros are essentially the same, so unify them. We keep the
_us version since it's a nice documentation for smaller timeouts.
v2: Fixup time unit conversion, _wait_for takes ms (Ville).
Cc: Jack Winter <jbh@alchemy.lu>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old code only handled either 6bpc or 8bpc. Since it's easy to do,
reorganize the code to be a bit more generic so that it can also handle
10bpc and 12bpc. Note that we still start with 8bpc, so there's no
functional change.
Also, since we no don't need to compute the 6BPC flag in the mode_valid
callback, we can consolidate things a bit. That requires though that
the link bw computation is moved up in the compute_config callback.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have a useful struct for this, let's use it. Some neat
pointer-chasing required, but it's all there already.
v2: Rebased on top of the added Haswell limited color range support.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used way too often in the enable/disable paths. And will
be even more useful in the future.
Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.
v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.
v3: Rebased on top of the hdmi/dp ddi encoder merging.
v4: Fixup stupid rebase error which lead to a NULL vfunc deref.
v5: On haswell the VGA port is on the PCH!
v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.
v7: Don't forget to git add ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Used by SDVO (and hopefully, eventually HDMI, if we ever get around
to fixing up the low dotclock CEA modes ...).
This required adding a new encoder->mode_set callback to be able to
pass around the intel_crtc_config.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only used by the lvds encoder. Note that we shouldn't do the same
simple conversion with the FORCE_6BPC flag, since that's much better
handled by moving all the pipe_bpc computation around.
This requires that we pass the pipe config around to encoders, so
that they can set special attributes and set constraints. To do so
introduce a new ->compute_config encoder callback, which is called in
stead of the drm crtc helper's ->mode_fixup.
To avoid massive churn all over the codebase we don't want to convert
all existing ->mode_fixup functions. Instead I've opted to convert
them on an as-needed basis (mostly to cut down on rebase conflicts and
to have more freedom to experiment around while developing the
patches).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently only containing the requested and the adjusted mode. And
only crtc callbacks are converted somewhat to it, encoders will be
done on a as-needed basis (simply too much churn in one patch
otherwise).
Future patches will add tons more useful stuff to this struct,
starting with the very simple.
v2: Store the pipe_config in the intel_crtc, so that the ->mode-set,
->enable and also ->disable have easy access to it.
v3: Store the pipe config in the right crtc ...
v4: Rebased.
v5: Fixup an OOPS when trying to kfree an ERR_PTR.
v6: Used drm_moode_copy and some other small cleanups as suggested
by Ville Syrjälä.
v7: drm_mode_copy preserves the mode id of the destination, so no need
to clear it again (Ville).
v8: Break a long line spotted by Paulo.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To clean up hotplug support we add a new enum to intel_encoder:
enum hpd_pin. It allows the encoder to request a hpd line but leave
the details which IRQ is responsible on which chipset generation
to i915_irq.c.
This way requesting hotplug support will become really simple on
the encoder/connector level.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be used to restore sprite state on resume.
v2: move sprite tracking bits up so we don't track modified sprite state
v3: use src_x/y in sprite suspend/resume code (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.
However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.
Fixes regression from commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's my promised pile of fixes for 3.9. I've dropped the core prep
patches for vt-switchless suspend/resume as discussed on irc. Highlights:
- Fix dmar on g4x. Not really gfx related, but I'm fed up with getting
blamed for dmar crapouts.
- Disable wc ptes updates on ilk when dmar is enabled (Chris). So again,
dmar, but this time gfx related :(
- Reduced range support for hsw, using the pipe CSC (Ville).
- Fixup pll limits for gen3/4 (Patrick Jakobsson). The sdvo patch is
already confirmed to fix 2 bug reports, so added cc: stable on that one.
- Regression fix for 8bit fb console (Ville).
- Preserve lane reversal bits on DDI/FDI ports (Damien).
- Page flip vs. gpu hang fixes (Ville). Unfortuntely not quite all of
them, need to decide what to do with the currently still in-flight ones.
- Panel fitter regression fix from Mika Kuoppala (was accidentally left on
on some pipes with the new modset code since 3.7). This also improves
the modeset sequence and might help a few other unrelated issues with
lvds.
- Write backlight regs even harder ... another installement in our eternal
fight against the BIOS and backlights.
- Fixup lid notifier vs. suspend/resume races (Zhang Rui). Prep work for
new ACPI stuff, but closing the race itself seems worthwile on its own.
- A few other small fixes and tiny cleanups all over.
Lots of the patches are cc: stable since I've stalled on a few
not-so-important fixes for 3.8 due to the grumpy noise Linus made.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (33 commits)
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
drm/i915: Implement pipe CSC based limited range RGB output
drm/i915: inverted brightness quirk for Acer Aspire 4736Z
drm/i915: Print the hw context status is debugfs
drm/i915: Use HAS_L3_GPU_CACHE in i915_gem_l3_remap
drm/i915: Fix PIPE_CONTROL DW/QW write through global GTT on IVB+
drm/i915: Set i9xx sdvo clock limits according to specifications
drm/i915: Set i9xx lvds clock limits according to specifications
drm/i915: Preserve the DDI link reversal configuration
drm/i915: Preserve the FDI line reversal override bit on CPT
drm/i915: add missing \n to UTS_RELEASE in the error_state
drm: Use C8 instead of RGB332 when determining the format from depth/bpp
drm: Fill depth/bits_per_pixel for C8 format
drm/i915: don't clflush gem objects in stolen memory
drm/i915: Don't wait for page flips if there was GPU reset
drm/i915: Kill obj->pending_flip
drm/i915: Fix a typo in a intel_modeset_stage_output_state() comment
drm/i915: remove bogus mutex_unlock from error-path
drm/i915: Print the pipe control page GTT address
...
Some (but not all) of the HDMI registers can be used to control sDVO,
so those registers have two names. IMHO, when we're talking about
HDMI, we really should call the HDMI control register "hdmi_reg"
instead of "sdvox_reg", otherwise we'll just confuse people reading
our code (we now have platforms with HDMI but without SDVO). So now
"struct intel_hdmi" has a member called "hdmi_reg" instead of
"sdvox_reg".
Also, don't worry: "struct intel_sdvo" still has a member called
"sdvo_reg".
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can remove some duplicated code and avoid more mistakes
and regressions with these registers in the future.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GPU reset will drop all flips that are still in the ring. So after the
reset, call update_plane() for all CRTCs to make sure the primary
planes are scanning out from the correct buffer.
Also finish all pending flips. That means user space will get its
page flip events and won't get stuck waiting for them.
v2: Explicitly finish page flips instead of relying on FLIP_DONE
interrupt being generated by the base address update.
v3: Make two loops over crtcs to avoid deadlocks with the crtc mutex
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup long line complaint from checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to:
commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Dec 11 15:18:28 2012 +0000
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a GPU reset occurs while a page flip has been submitted to the ring,
the flip will never complete once the ring has been reset.
The GPU reset can be detected by sampling the reset_counter before the
flip is submitted, and then while waiting for the flip, the sampled
counter is compared with the current reset_counter value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Move the reset_counter assignment to an earlier place in
common code as discussed on the mailing list.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60140
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the driver is in control of whether it needs to disable
everything at take-over or not, we can rip this all out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding the fb idle detection to mark-inactive, it was forgotten
that userspace can drive the processing of retire-requests. We assumed
that it would be principally driven by the retire requests worker,
running once every second whilst active and so we would get the deferred
timer for free. Instead we spend too many CPU cycles reclocking the LVDS
preventing real work from being done.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alexander Lam <lambchop468@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58843
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our suspend code touches a lot of registers all over the place, so we
need to enable the power well before suspending.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup compilation by stealing the header decl from the
dynamic power wells patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was wrong in many different ways, so this is a full
rewrite. We don't have "different power wells for different parts of
the GPU", we have a single power well, but we have multiple registers
that can be used to request enabling/disabling the power well. So
let's be a good citizen and only use the register we're suppose to
use, except when we're loading the driver, where we clear the request
made by the BIOS.
If any of the registers is requesting the power well to be enabled, it
will be enabled. If none of the registers is requesting the power well
to be enabled, it will be disabled.
For now we're just forcing the power well to be enabled, but in the
next commits we'll change this.
V2:
- Remove debug messages that could be misleading due to possible
race conditions with KVMr, Debug and BIOS.
- Don't wait on disabling: after a conversaion with a hardware
engineer we discovered that the "restriction" on bit 31 is just
for the "enable" case, and we don't even need to wait on the
"disable" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ELD info should be updated dynamically according to hot plug event.
For haswell chip, clear/set the eld valid bit and output enable bit
from callback intel_disable/eanble_ddi().
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The AVI infoframe is able to inform the display whether the source is
sending full or limited range RGB data.
As per CEA-861 [1] we must first check whether the display reports the
quantization range as selectable, and if so we can set the approriate
bits in the AVI inforframe.
[1] CEA-861-E - 6.4 Format of Version 2 AVI InfoFrame
v2: Give the Q bits better names, add spec chapter information
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new "Automatic" mode to the "Broadcast RGB" range property.
When selected the driver automagically selects between full range and
limited range output.
Based on CEA-861 [1] guidelines, limited range output is selected if the
mode is a CEA mode, except 640x480. Otherwise full range output is used.
Additionally DVI monitors should most likely default to full range
always.
As per DP1.2a [2] DisplayPort should always use full range for 18bpp, and
otherwise will follow CEA-861 rules.
NOTE: The default value for the property will now be "Automatic"
so some people may be affected in case they're relying on the
current full range default.
[1] CEA-861-E - 5.1 Default Encoding Parameters
[2] VESA DisplayPort Ver.1.2a - 5.1.1.1 Video Colorimetry
v2: Use has_hdmi_sink to check if a HDMI monitor is present
v3: Add information about relevant spec chapters
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The RGB color range select bit on the DP/SDVO/HDMI registers
disappeared when PCH was introduced, and instead a new PIPECONF bit
was added that performs the same function.
Add a new INTEL_MODE_LIMITED_COLOR_RANGE private mode flag, and set
it in the encoder mode_fixup if limited color range is requested.
Set the the PIPECONF bit 13 based on the flag.
Experimentation showed that simply toggling the bit while the pipe is
active doesn't work. We need to restart the pipe, which luckily already
happens.
The DP/SDVO/HDMI bit 8 is marked MBZ in the docs, so avoid setting it,
although it doesn't seem to do any harm in practice.
TODO:
- the PIPECONF bit too seems to have disappeared from HSW. Need a
volunteer to test if it's just a documentation issue or if it's really
gone. If the bit is gone and no easy replacement is found, then I suppose
we may need to use the pipe CSC unit to perform the range compression.
v2: Use mode private_flags instead of intel_encoder virtual functions
v3: Moved the intel_dp color_range handling after bpc check to help
later patches
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Note: This patch also adds a little helper intel_crtc_restore_mode for
the common case where we do a full modeset but with the same
parameters, e.g. to undo bios damage or update a property.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Added note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If you unplug the hdmi connector slowly enough, the hotplug interrupt
fires but then the kernel code tries to read the EDID and succeeds
(because the connector is still half connected, the HPD pin is shorter
than the others, and DDC works). Since EDID succeeds it thinks the
monitor is still connected.
To prevent that, read the live HPD status in the hotplug handler before
trying to read the EDID.
v2: Rename the function to ibx_ (Chris Wilson)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55372
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For GMCH platforms we set up the hpd irq registers in the irq
postinstall hook. But since we only enable the irq sources we actually
need in PORT_HOTPLUG_EN/STATUS, taking dev_priv->hotplug_supported_mask
into account, no hpd interrupt sources is enabled since
commit 52d7ecedac
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Dec 1 21:03:22 2012 +0100
drm/i915: reorder setup sequence to have irqs for output setup
Wrongly set-up interrupts also lead to broken hw-based load-detection
on at least GM45, resulting in ghost VGA/TV-out outputs.
To fix this, delay the hotplug register setup until after all outputs
are set up, by moving it into a new dev_priv->display.hpd_irq_callback.
We might also move the PCH_SPLIT platforms to such a setup eventually.
Another funny part is that we need to delay the fbdev initial config
probing until after the hpd regs are setup, for otherwise it'll detect
ghost outputs. But we can only enable the hpd interrupt handling
itself (and the output polling) _after_ that initial scan, due to
massive locking brain-damage in the fbdev setup code. Add a big
comment to explain this cute little dragon lair.
v2: Encapsulate all the fbdev handling by wrapping the move call into
intel_fbdev_initial_config in intel_fb.c. Requested by Chris Wilson.
v3: Applied bikeshed from Jesse Barnes.
v4: Imre Deak noticed that we also need to call intel_hpd_init after
the drm_irqinstall calls in the gpu reset and resume paths - otherwise
hotplug will be broken. Also improve the comment a bit about why
hpd_init needs to be called before we set up the initial fbdev config.
Bugzilla: Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54943
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More specifically, the LPT FDI RX only supports 8bpc and a maximum of
2 lanes, so anything above that won't work and should be rejected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a prep patch to make this a property of intel_lvds. Makes more
sense, removes clutter from intel_display.c and eventually I want to
move all the encoder special cases wrt clock handling to encoders
anyway.
v2: Add an intel_ prefixe to is_dual_link_lvds since it's non-static
now.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we have two encoder specific bits in the common mode_set
functions:
- lvds pin pair enabling
- dp m/n setting and computation
Now the lvds stuff needs to happen before the pll is enabled. Since
that is done in the crtc_mode_set functions, we need to add a new
callback to be able to move them to the encoder code (where they
belong). The dp m/n stuff is a giant mess anyway (since it also
confuses itself with the fdi link m/n handling), so that needs to be
handled separately.
I think that we can move the pll enabling down quite a bit, which
might allow us to eventually merge encoder->pre_enable with this new
pre_pll_enable callback. But for now this will allow us to clean
things up a bit.
Note that vlv doesn't support lvds, hence we don't need to change
anything in there.
v2: Fixup commit message, both suggested from Paulo Zanoni.
- dp m/n doesn't need to happen before pll enabling
- lvds doesn't exist on vlv, hence no changes required in the vlv pll
function.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we accumulate unpin tasks because we are pageflipping faster than the
system can schedule its workers, we can effectively create a
pin-leak. The solution taken here is to limit the number of unpin tasks
we have per-crtc and to flush those outstanding tasks if we accumulate
too many. This should prevent any jitter in the normal case, and also
prevent the hang if we should run too fast.
Note: It is important that we switch from the system workqueue to our
own dev_priv->wq since all work items on that queue are guaranteed to
only need the dev->struct_mutex and not any modeset resources. For
otherwise if we have a work item ahead in the queue which needs the
modeset lock (like the output detect work used by both polling or
hpd), this work and so the unpin work will never execute since the
pageflip code already holds that lock. Unfortunately there's no
lockdep support for this scenario in the workqueue code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46991
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about workqueu deadlock.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56337
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This covers the "Disable FDI" section from the CRT mode set sequence.
This disables the FDI receiver and also the FDI pll.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now intel_ddi_init is just like intel_hdmi_init and intel_dp_init: it
inits the encoder and then calls the proper init_connector functions.
Notice that for non-eDP ports we call both HDMI and DP connector init,
so we have 2 connectors attached to each DDI encoder.
After this change, intel_hdmi_init and intel_dp_init are only called
by Ivy Bridge and earlier, while hardware containing DDI outputs
should call intel_ddi_init.
Also added/removed quite a few "static" keywords due to the fact that
some function pointers were moved from intel_dp.c and intel_hdmi.c to
intel_ddi.c.
DP finally works on Haswell now! \o/
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this since now on DDI we will have 2 connectors on each
encoder.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both "intel_dp" and "intel_hdmi" structs had a "port" field, which
always had the same value. It makes more sense to move this to
intel_digital_port, so we can know the port independently of the
connector type.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to have one single encoder capable of controlling both DP
and HDMI outputs. This patch just adds the initial infrastructure, no
functional changes.
Previously, both intel_dp and intel_hdmi were intel_encoders. Now,
these 2 structs do not have intel_encoder as members anymore. The new
struct intel_digital_port has intel_encoder as a member, and it also
includes intel_dp and intel_hdmi as members. In other words: see the
changes inside intel_drv.h: it's the most important change, everything
else is only to make it compile and work.
For now, each intel_digital_port is still only able to control one of
HDMI or DP, but not both together.
In the future we should also try to merge the common fields from
intel_dp and intel_hdmi (e.g., port).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add the missing ' ' spotted by Damien Lespiau.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like in:
commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
but this time, for the sprite planes. This ensures that the
sprite offset are always inside the supported hardware limits since it
becomes the offset into a page and we adjust the base address to a page
boundary.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for supporting scaling mode configuration also in eDP.
Includes a drive-by-removal of an outdated comment about fitting mode.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an important step :)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cdclk frequency is not always the same, so the value here should
be adjusted to match it.
Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.
Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.
V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).
For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.
For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.
V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.
We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.
In other words:
Imagine the following case:
xrandr --output eDP1 --auto --crtc 0
xrandr --output eDP1 --off
xrandr --output eDP1 --auto --crtc 2
After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.
So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Identical #define is now available in include/drm/drm_dp_helper.h, nuke the
dupe.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.
Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.
Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell does not have a scaler in the sprite pipeline anymore, so let's
ensure:
1/ We bail out of update_plate() when someone is trying to ask to
display a scaled framebuffer,
2/ We never write to the nonexistent SPR_SCALE register
v2: Smash in the fixup from Damien in the disable_plane function.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (for v1)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the cached EDID from intel_dp and intel_lvds_connector to
intel_connector. Unify cached EDID handling for LVDS and eDP, in
preparation for adding more generic EDID caching later.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pave the way for sharing some logic between eDP and LVDS.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create a generic struct intel_panel for sharing a data structure and code
between eDP and LVDS panels. Add the new struct to intel_connector so that
later on we can have generic EDID and mode reading functions with EDID
caching that transparently fallback to fixed mode when EDID is not
available.
Add intel_panel as a dummy first, and move data (such as the mentioned
fixed mode) to it in later patches.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup tiny conflict in intel_dp_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of saved int_lvds_connector and int_edp_connector in
drm_i915_private.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previous patch "drm/i915: add basic Haswell DP link train bits"
implemented the basic structure to set the voltage levels and training
patterns. This patch adds the higher-level bits that are part of the
mode set sequence and hot plug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Problems with the previous code:
- HDMI just uses WRPLL1 for everything, so dual head cases might not
work sometimes.
- At encoder->mode_set we just write the PLL register without doing
any kind of check (e.g., check if the PLL is already being used).
- There is no way to fail and return error codes at
encoder->mode_set.
- We write to PORT_CLK_SEL at mode_set and we never disable it.
- Machines hang due to wrong clock enable/disable sequence.
So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
- Check PLL availability at ironlake_crtc_mode_set.
- Try to use both WRPLLs.
- Check if PLLs are used before actually trying to use them, and
properly fail with error messages.
- Enable/disable PORT_CLK_SEL at the right place.
- Add some WARNs to check for bugs.
The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we were enabling it at mode_set but never disabling. Let's
follow the mode set sequence.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.
This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Bigger -fixes pile, mostly because I've included Ajax' DP dongle stuff,
as discussed on irc. Otherwise just small things:
- regression fix to finally make 6bpc auto-dither on dp work (Jani)
- reinstate an snb ctx w/a that accidentally got lost in a rework (Chris)
- fixup the DP train sequence, logic-goof-up uncovered by Coverty (Chris)
- fix set_caching locking (Ben)
- fix spurious segfault on con-current gtt mmap faulting (Dimitry and Mika)
- some pageflip correctness fixes (still hunting down some issues, but
these are the worst offenders of confused code that we've tracked down
thus far) from Chris and me
- fixup swizzling settings on vlv (Jesse)
- gt_mode w/a from Ben added, fixes snb gt1 rc6+hw ctx hangs.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix GT_MODE default value
drm/i915: don't frob the vblank ts in finish_page_flip
drm/i915: call drm_handle_vblank before finish_page_flip
drm/i915: print warning if vmi915_gem_fault error is not handled
drm/i915: EBUSY status handling added to i915_gem_fault().
drm/i915: Try harder to complete DP training pattern 1
drm/i915: set swizzling to none on VLV
drm/dp: Make sink count DP 1.2 aware
drm/dp: Document DP spec versions for various DPCD registers
drm/i915/dp: Be smarter about connection sense for branch devices
drm/i915/dp: Fetch downstream port info if needed during DPCD fetch
drm/dp: Update DPCD defines
drm: Export drm_probe_ddc()
drm/i915: Flush the pending flips on the CRTC before modification
drm/i915: Actually invalidate the TLB for the SandyBridge HW contexts w/a
drm/i915: Fix set_caching locking
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
v2: Fix parenthesis mismatch, spotted by Jani Nikula
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup merge conflict and MAX_DOWNSTREAM #define as spotted by
Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fix parenthesis mismatch, spotted by Jani Nikula
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fixup merge conflict and MAX_DOWNSTREAM #define as spotted by
Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cpu eDP encoder has some horrible hacks to set up the DP pll at
the right time. To be able to move them to the right place, add some
more encoder callbacks so that this can happen at the right time.
LVDS has some similar funky hacks, but that would require more work
(we need to move around the pll setup a bit). Hence for now only
wire these new callbacks up for ilk+ - we only have cpu eDP on these
platforms.
v2: Bikeshed the vtable ordering, requested by Chris Wilson.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a quick reference I'll detail the motivation and design of the new code a
bit here (mostly stitched together from patchbomb announcements and commits
introducing the new concepts).
The crtc helper code has the fundamental assumption that encoders and crtcs can
be enabled/disabled in any order, as long as we take care of depencies (which
means that enabled encoders need an enabled crtc to feed them data,
essentially).
Our hw works differently. We already have tons of ugly cases where crtc code
enables encoder hw (or encoder->mode_set enables stuff that should only be
enabled in enocder->commit) to work around these issues. But on the disable
side we can't pull off similar tricks - there we actually need to rework the
modeset sequence that controls all this. And this is also the real motivation
why I've finally undertaken this rewrite: eDP on my shiny new Ivybridge
Ultrabook is broken, and it's broken due to the wrong disable sequence ...
The new code introduces a few interfaces and concepts:
- Add new encoder->enable/disable functions which are directly called from the
crtc->enable/disable function. This ensures that the encoder's can be
enabled/disabled at a very specific in the modeset sequence, controlled by our
platform specific code (instead of the crtc helper code calling them at a time
it deems convenient).
- Rework the dpms code - our code has mostly 1:1 connector:encoder mappings and
does support cloning on only a few encoders, so we can simplify things quite a
bit.
- Also only ever disable/enable the entire output pipeline. This ensures that
we obey the right sequence of enabling/disabling things, trying to be clever
here mostly just complicates the code and results in bugs. For cloneable
encoders this requires a bit of special handling to ensure that outputs can
still be disabled individually, but it simplifies the common case.
- Add infrastructure to read out the current hw state. No amount of careful
ordering will help us if we brick the hw on the initial modeset setup. Which
could happen if we just randomly disable things, oblivious to the state set up
by the bios. Hence we need to be able to read that out. As a benefit, we grow a
few generic functions useful to cross-check our modeset code with actual hw
state.
With all this in place, we can copy&paste the crtc helper code into the
drm/i915 driver and start to rework it:
- As detailed above, the new code only disables/enables an entire output pipe.
As a preparation for global mode-changes (e.g. reassigning shared resources) it
keeps track of which pipes need to be touched by a set of bitmasks.
- To ensure that we correctly disable the current display pipes, we need to
know the currently active connector/encoder/crtc linking. The old crtc helper
simply overwrote these links with the new setup, the new code stages the new
links in ->new_* pointers. Those get commited to the real linking pointers once
the old output configuration has been torn down, before the ->mode_set
callbacks are called.
- Finally the code adds tons of self-consistency checks by employing the new hw
state readout functions to cross-check the actual hw state with what the
datastructure think it should be. These checks are done both after every
modeset and after the hw state has been read out and sanitized at boot/resume
time. All these checks greatly helped in tracking down regressions and bugs in
the new code.
With this new basis, a lot of cleanups and improvements to the code are now
possible (besides the DP fixes that ultimately made me write this), but not yet
done:
- I think we should create struct intel_mode and use it as the adjusted mode
everywhere to store little pieces like needs_tvclock, pipe dithering values or
dp link parameters. That would still be a layering violation, but at least we
wouldn't need to recompute these kinds of things in intel_display.c. Especially
the port bpc computation needed for selecting the pipe bpc and dithering
settings in intel_display.c is rather gross.
- In a related rework we could implement ->mode_valid in terms of ->mode_fixup
in a generic way - I've hunted down too many bugs where ->mode_valid did the
right thing, but ->mode_fixup didn't. Or vice versa, resulting in funny bugs
for user-supplied modes.
- Ditch the idea to rework the hdp handling in the common crtc helper code and
just move things to i915.ko. Which would rid us of the ->detect crtc helper
dependencies.
- LVDS wire pair and pll enabling is all done in the crtc->mode_set function
currently. We should be able to move this to the crtc_enable callbacks (or in
the case of the LVDS wire pair enabling, into some encoder callback).
Last, but not least, this new code should also help in enabling a few neat
features: The hw state readout code prepares (but there are still big pieces
missing) for fastboot, i.e. avoiding the inital modeset at boot-up and just
taking over the configuration left behind by the bios. We also should be able
to extend the configuration checks in the beginning of the modeset sequence and
make better decisions about shared resources (which is the entire point behind
the atomic/global modeset ioctl).
Tested-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Acked-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have solid modeset state tracking and checking code in
place, we can do the Full Monty also after dpms calls.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this to avoid confusing the hw state readout code with the cpt
pch plls at resume time: We'd read the new pipe state (which is
disabled), but still believe that we have a life pll connected to that
pipe (from before the suspend). Hence properly disable pipes to clear
out all the residual state.
This has the neat side-effect that we don't enable ports prematurely
by restoring bogus state from the saved register values.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this change we can (finally!) rip out a few of the temporary hacks
and clean up a few other things:
- Kill intel_crtc_prepare_encoders, now unused.
- Kill the hacks in the crtc_disable/enable functions to always call the
encoder callbacks, we now always call the crtc functions with the right
encoder -> crtc links.
- Also push down the crtc->enable, encoder and connector dpms state
updates. Unfortunately we can't add a WARN in the crtc_disable
callbacks to ensure that the crtc is always still enabled when
disabling an output pipe - the crtc sanitizer of the hw readout path
can hit this when it needs to disable an active pipe without any
enabled outputs.
- Only call crtc->disable if the pipe is already enabled - again avoids
running afoul of the new WARN.
v2: Copy&paste our own version of crtc_in_use, too.
v3: We need to update the dpms an encoder->connectors_active states,
too.
v4: I've forgotten to kill the unconditional encoder->disable calls in
the crtc_disable functions.
v5: Rip out leftover debug printk.
v6: Properly clear intel_encoder->connectors_active. This wasn't
properly cleared when disabling an encoder because it was no longer on
the new connector list, but the crtc was still enabled (i.e. switching
the encoder of an active crtc). Reported by Jani Nikula.
v7: Don't clobber the encoder->connectors_active state of untouched
encoders. Since X likes to first disable all outputs with dpms off
before setting a new framebuffer, this hit a few warnings. Reported by
Paulo Zanoni.
v8: Kill the now stale comment warning that intel_crtc->active is not
always updated at the right times.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because that's what it is. Unfortunately we can't rip this out because
the fb helper has an incetious relationship with the crtc helper - it
likes to call disable_unused_functions, among other things.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The "is this encoder cloned" check will be reused by the lvds encoder,
hence exract it.
v2: Be a bit more careful about that we need to check the new, staged
ouput configuration in the check_non_cloned helper ...
v3: Kill the double negation with s/!non_cloned/is_cloned/, suggested
by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing in the old fb, having overwritten the current fb, leads to
some neatly convoluted code. It's much simpler if we defer the
crtc->fb update to the place that updates the hw, in pipe_set_base.
This way we also don't need to restore anything in case something
fails - we only update crtc->fb once things have succeeded.
The real reason for this change is that now we keep the old fb
assigned to crtc->fb, which allows us to finally move the crtc disable
case into the common low-level set_mode function in the next patch.
Also don't clobber crtc->x and crtc->y, we neatly pass these down the
callchain already. Unfortunately we can't do the same with crtc->mode,
because that one is being used in the mode_set callbacks.
v2: Don't restore the drm_crtc object any more on failed modesets,
since we've lose an fb reference otherwise. Also (and this is the
reason this has been found), this totally confused the modeset state
tracking, since it clobbers crtc->enabled. Issue reported by Paulo
Zanoni.
v3: Rip out the entire crtc saving into struct intel_set_config, not
just the restoring part.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the core of the new modeset logic.
The current code which is based upon the crtc helper code first
updates all the link of the new display pipeline and then calls the
lower-level set_mode function to execute the required callbacks to get
there. The issue with this approach is that for disabling we need to
know the _current_ display pipe state, not the new one.
Hence we need to stage the new state of the display pipe and only
update it once we have disabled the current configuration and before we
start to update the hw registers with the new configuration.
This patch here just prepares the ground by switching the new output
state computation to these staging pointers. To make it clearer,
rename the old update_output_state function to stage_output_state.
A few peculiarities:
- We're also calling the set_mode function at various places to update
properties. Hence after a successfule modeset we need to stage the
current configuration (for otherwise we might fall back again). This
happens automatically because as part of the (successful) modeset we
need to copy the staged state to the real one. But for the hw
readout code we need to make sure that this happens, too.
- Teach the new staged output state computation code the required
smarts to handle the disabling of outputs. The current code handles
this in a special case, but to better handle global modeset changes
covering more than one crtc, we want to do this all in the same
low-level modeset code.
- The actual modeset code is still a bit ugly and wants to know the new
crtc->enabled state a bit early. Follow-on patches will clean that
up, for now we have to apply the staged output configuration early,
outside of the set_mode functions.
- Improve/add comments in stage_output_state.
Essentially all that is left to do now is move the disabling code into
set_mode and then move the staged state update code also into
set_mode, at the right place between disabling things and calling the
mode_set callbacks for the new configuration.
v2: Disabling a crtc works by passing in a NULL mode or fb, userspace
doesn't hand in the list of connectors. We therefore need to detect
this case manually and tear down all the output links.
v3: Properly update the output staging pointers after having read out
the hw state.
v4: Simplify the code, add more DRM_DEBUG_KMS output and check a few
assumptions with WARN_ON. Essentially all things that I've noticed
while debugging issues in other places of the code.
v4: Correctly disable the old set of connectors when enabling an
already enabled crtc on a new set of crtc. Reported by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We actually only touch the connector -> encoder and encoder -> crtc
linking. So it's enough to just save/restore that.
While at it, also switch to kcalloc to allocate these arrays (omission
in the commit message spotted by Jesse Barnes).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This computes what exactly changed in the modeset configuration, i.e.
whether a full modeset is required or only an update of the
framebuffer base address or no change at all.
In the future we might add more checks for e.g. when only the output
mode changed, so that we could do a minimal modeset for outputs that
support this. Like the lvds/eDP panels where we only need to update
the panel fitter.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_crtc_set_config is an unwidly beast and is in serious need of
some function extraction. To facilitate that, introduce a struct to
keep track of all the state involved. Atm it doesn't do much more than
keep track of all the allocated memory.
v2: Apply some bikeshed to intel_set_config_free, as suggested by
Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now track the connector state in encoder->connectors_active, and
because the DP output can't be cloned, that is sufficient to track the
link state. Hence use this instead of adding yet another modeset state
variable with dubious semantics at driver load and resume time.
Also, connectors_active should only ever be set when the encoder is
linked to a crtc, hence convert that crtc test into a WARN.
v2: Rebase on top of struct intel_dp moving.
v3: The rebase accidentally killed the newly-introduced intel_dp->port
Noticed by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Afaict this has been used for two things:
- To prevent the crtc enable code from being run twice. We have now
intel_crtc->active to track this in a more precise way.
- To ensure the code copes correctly with the unknown hw state after
boot and resume. Thanks to the hw state readout and sanitize code we
have now a better way to handle this.
The only thing it still does is complicate our modeset state space.
Having outlived its usefullness, let it just die.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we can only check the connector state after a dpms call - while
doing modeset with the copy&pasted crtc helper code things are too
ill-defined for proper checking. But the idea is very much to call
this check from the modeset code, too.
v2: Fix dpms check and don't presume that if the hw isn't on that it
must not be linked up with an encoder (it could simply be switched off
with the dpms state).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is all glorious if we try really hard to only enable/disable an
entire display pipe to ensure that everyting happens in the right
order. But if we don't know the output configuration when the driver
takes over, this will all be for vain because we'll make the hw angry
right on the first modeset - we don't know what outputs/ports are
enabled and hence have to disable everything in a rather ad-hoc way.
Hence we need to be able to read out the current hw state, so that we
can properly tear down the current hw state on the first modeset.
Obviously this is also a nice preparation for the fastboot work, where
we try to avoid the modeset on driver load if it matches what the hw
is currently using.
Furthermore we'll be using these functions to cross-check the actual
hw state with what we think it should be, to ensure that the modeset
state machine actually works as advertised.
This patch only contains the interface definitions and a little helper
for the simple case where we have a 1:1 encoder to connector mapping.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the first tiny step towards cross-checking the entire modeset
state machine with WARNs. A crtc can only be enabled when it's
actually in use, i.e. crtc->active imlies crtc->enabled.
Unfortunately we can't (yet) check this when disabling the crtc,
because the crtc helpers are a bit slopy with updating state and
unconditionally update crtc->enabled before changing the hw state.
Fixing that requires quite some more work.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new infrastructure we're doing this when enabling/disabling
the entire display pipe.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Together with the static helper functions drm_crtc_prepare_encoders
and drm_encoder_disable (which will be simplified in the next patch,
but for now are 1:1 copies). Again, no changes beside new names for
these functions.
Also call our new set_mode instead of the crtc helper one now in all
the places we've done so far.
v2: Call the function just intel_set_mode to better differentia it
from intel_crtc_mode_set which really only does the ->mode_set step of
the entire modeset sequence on one crtc. Whereas this function does
the global change.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We no longer need them. And now that all encoders are converted, we
can finally move the cpt modeset check to the right place - at the end
of the crtc_enable function.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yeah, big patch but I couldn't come up with a neat idea of how to
split it up further, that wouldn't break dpms on cloned configs
somehow. But the changes in dvo/sdvo/crt are all pretty much
orthonogal, so it's not too bad a patch.
These are the only encoders that support cloning, which requires a few
special changes compared to the previous patches.
- Compute the desired state of the display pipe by walking all
connected encoders and checking whether any has active connectors.
To make this clearer, drop the old mode parameter to the crtc dpms
function and rename it to intel_crtc_update_dpms.
- There's the curious case of intel_crtc->dpms_mode. With the previous
patches to remove the overlay pipe A code and to rework the load
detect pipe code, the big users are gone. We still keep it to avoid
enabling the pipe twice, but we duplicate this logic with
crtc->active, too. Still, leave this for now and just push a fake
dpms mode into it that reflects the state of the display pipe.
Changes in the encoder dpms functions:
- We clamp the dpms state to the supported range right away. This is
escpecially important for the VGA outputs, where only older hw
supports the intermediate states. This (and the crt->adpa_reg patch)
allows us to unify the crt dpms code again between all variants
(gmch, vlv and pch).
- We only enable/disable the output for dvo/sdvo and leave the encoder
running. The encoder will be disabled/enabled when we switch the
state of the entire output pipeline (which will happen right away
for non-cloned setups). This way the duplication is reduced and
strange interaction when disabling output ports at the wrong time
avoided.
The dpms code for all three types of connectors contains a bit of
duplicated logic, but I think keeping these special cases separate is
simpler: CRT is the only one that hanldes intermediate dpms state
(which requires extra logic to enable/disable things in the right
order), and introducing some abstraction just to share the code
between dvo and sdvo smells like overkill. We can do that once someone
bothers to implement cloning for the more modern outputs. But I doubt
that this will ever happen.
v2: s/crtc/crt/_set_dpms, noticed by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've picked hdmi as the first encoder to convert because it's rather
simple:
- no cloning possible
- no differences between prepare/commit and dpms off/on switching.
A few changes are required to do so:
- Split up the dpms code into an enable/disable function and wire it
up with the intel encoder.
- Noop out the existing encoder prepare/commit functions used by the
crtc helper - our crtc enable/disable code now calls back into the
encoder enable/disable code at the right spot.
- Create new helper functions to handle dpms changes.
- Add intel_encoder->connectors_active to better track dpms state. Atm
this is unused, but it will be useful to correctly disable the
entire display pipe for cloned configurations. Also note that for
now this is only useful in the dpms code - thanks to the crtc
helper's dpms confusion across a modeset operation we can't (yet)
rely on this having a sensible value in all circumstances.
- Rip out the encoder helper dpms callback, if this is still getting
called somewhere we have a bug. The slight issue with that is that
the crtc helper abuses dpms off to disable unused functions. Hence
we also need to implement a default encoder disable function to do
just that with the new encoder->disable callback.
- Note that we drop the cpt modeset verification in the commit
callback, too. The right place to do this would be in the crtc's
enable function, _after_ all the encoders are set up. But because
not all encoders are converted yet, we can't do that. Hence disable
this check temporarily as a minor concession to bisectability.
v2: Squash the dpms mode to only the supported values -
connector->dpms is for internal tracking only, we can hence avoid
needless state-changes a bit whithout causing harm.
v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just prep work, not yet put to some use.
Note that because we're still using the crtc helper to switch modes
(and their complicated way to do partial modesets), we need to call
the encoder's disable function unconditionally.
But once this is cleaned up we shouldn't call the encoder's disable
function unconditionally any more, because then we know that we'll
only call it if the encoder is actually enabled. Also note that we
then need to be careful about which crtc we're filtering the encoder
list on: We want to filter on the crtc of the _current_ mode, not the
one we're about to set up.
For the enabling side we need to do the same trick. And again, we
should be able to simplify this quite a bit when things have settled
into place.
Also note that this simply does not take cloning into account, so dpms
needs to be handled specially for the few outputs where we even bother
with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As part of the advice given to us from the hardware designers regarding
the maximum wait time on the forcewake handshake we need to move from us
granularity to ms granularity. In earlier patches to do this, Jani
noticed that wait_for_us was properly converted to use cpu_relax(), but
wait_for was not.
The issue has existed since the introduction of the macro:
commit 913d8d1100
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Aug 7 11:01:35 2010 +0100
drm/i915: Ensure that while(INREG()) are bounded (v2)
CC: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
"New stuff for -next. Highlights:
- prep patches for the modeset rework. Note that one of those patches
touches the fb helper in the common drm code.
- hasw hdmi audio support (Wang Xingchao)
- improved instdone dumping for gen7 (Ben)
- unbound tracking and a few follow-up patches from Chris
- dma_buf->begin/end_cpu_access plus fix for drm/udl (Dave)
- improve mmio error reporting for hsw
- prep patch for WQ_NON_REENTRANT removal (Tejun Heo)
"
* 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (41 commits)
drm/i915: Remove __GFP_NO_KSWAPD
drm/i915: disable rc6 on ilk when vt-d is enabled
drm/i915: Avoid unbinding due to an interrupted pin_and_fence during execbuffer
drm/i915: Use new INSTDONE registers (Gen7+)
drm/i915: Add new INSTDONE registers
drm/i915: Extract reading INSTDONE
drm/i915: Use a non-blocking wait for set-to-domain ioctl
drm/i915: Juggle code order to ease flow of the next patch
drm/i915: Use cpu relocations if the object is in the GTT but not mappable
drm/i915: Extract general object init routine
drm/i915: Protect private gem objects from truncate (such as imported dmabuf)
drm/i915: Only pwrite through the GTT if there is space in the aperture
i915: use alloc_ordered_workqueue() instead of explicit UNBOUND w/ max_active = 1
drm/i915: Find unclaimed MMIO writes.
drm/i915: Add ERR_INT to gen7 error state
drm/i915: Cantiga+ cannot handle a hsync front porch of 0
drm/i915: fix reassignment of variable "intel_dp->DP"
drm/i915: Try harder to allocate an mmap_offset
drm/i915: Show pin count in debugfs
drm/i915: Show (count, size) of purgeable objects in i915_gem_objects
...
There was some merge conflicts in -next and they weren't so pretty, so
backmerge now to avoid them.
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_modes.c
Since it's redundant - we can get the attached encoder in the
functions themselves.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the connector update part of intel_ddc_get_modes() into a separate
intel_connector_update_modes() function for reuse. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45881
Tested-by: Alex Ferrando <alferpal@gmail.com>
Cc: stable@vger.kernel.org (for 3.4+3.5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQLWtvAAoJEHm+PkMAQRiG/DYH+wd0FqfEuYkYk4KPyAPuhKpX
zX7HYfLvyJE/ZYIdrhjq1E6Xm2KNr7gtX7/Rdzi2W38M9sjbYzwG1UGIw51qnxWy
yZJH9BGkfyQgQPeuDGohfB6DkDy2JWr2eqMDvakjOwgBsIzji0PQD/f3UvndhtUa
c+tTj/kjavHE1Yr2Wy6OnRZz3Uc0hIMn/Q0JqtbCs3LUgEV1KA4OEAe56XNz4Ku4
WE+FFaGFPvtriQsQON+ohPS5IC8jzQGK/0vbrJ4lWjFnZy4gvZXnborTOwD0WSQG
fbsNuxp1AaM2/pqfMwXm1w0ADvwOITHNiwwXf9id6DoK81QwTFpUdvKpn6yB6gQ=
=rurr
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc2' into drm-intel-next
Backmerge Linux 3.6-rc2 to resolve a few funny conflicts before we put
even more madness on top:
- drivers/gpu/drm/i915/i915_irq.c: Just a spurious WARN removed in
-fixes, that has been changed in a variable-rename in -next, too.
- drivers/gpu/drm/i915/intel_ringbuffer.c: -next remove scratch_addr
(since all their users have been extracted in another fucntion),
-fixes added another user for a hw workaroudn.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reasons that are not apparent to anybody, 990bbdadab (drm/i915:
Group the GT routines together in both code and vtable) breaks the use
of the BitStream Decoder ring on SandyBridge. The active ingredient of
that patch is the conversion from a udelay(10) to a udelay(1) in the
busy-wait loop of waiting for the forcewake acknowledge. If we restore
that udelay(10) or insert another udelay(1) afterwards (or any wait
longer than 250ns) everything works again. An alternative is also to
remove any delay from the busy-wait loop.
Given that in the atomic sections we want to complete the wait as quick
as possible to avoid blocking the CPU for too long, it makes sense to
remove the delay altogether and simply spin on the exit condition until
it completes. So we replace the udelay(1) with cpu_relax().
Papers over regression from
commit 990bbdadab
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jul 2 11:51:02 2012 -0300
drm/i915: Group the GT routines together in both code and vtable
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function isn't used outside of intel_panel.c, so make it static.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.
Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As suggested by Daniel, rip out the independent timers for device and
crtc busyness and integrate the manual powermanagement of the display
engine into the GEM core and its request tracking. The benefits are that
the code is a lot smaller, fewer moving parts and should fit more neatly
into the overall activity tracking of the driver.
v2: Complete overhaul and removal of the racy timers and workers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for Haswell, but already has its uses here.
This patch started as a small patch written patch by Shobhit Kumar,
but it has changed so much that none of its original lines remain.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of having a giant if cascade to figure this out according to
the passed-in register. We could do quite a bit more cleaning up and
all by using the port at more places, but I think this should be part
of a bigger rework to introduce a struct intel_digital_port which
would keep track of all these things. I guess this will be part of
some haswell-DP-induced refactoring.
For now this rips out the big cascade, which is what annoyed me so
much.
v2: Add port variable name back for the func decl (I've tried to trick
myself below the 80 char limit).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).
Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
gen3+, so no problem. Note that the old code had a bug and didn't
allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
work, but the only reason I've found is that you can't use the
panel-fitter (used for lvds upscaling) with anything else. But we
don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
a) rather confusing b) mostly as a guideline to implementors (i.e.
explicitly stating what is already implicit from the spec, without
always going into the details of why). So I think we can ignore this
- worst case we'll get a bug report from a user with with sdvo-lvds
and sdvo-tmds and have to add that special case back in.
Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.
Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.
v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the DP structure to shared location so that it can be used from
within the ddi module.
Changes from Paulo:
- Move less code to intel_drv.h
- Remove #include statement
- Replace a tab with a space in train_set
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have way too much lying hardware to rely on a simple "does someone
answer on the ddc i2c address?" check. And now it's unused, so just
kill it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid recomputing the display framebuffer offset on gen2/3
pageflips. This is also prep work to do similar trickery on gen4+
Also:
- kill "Start", such upper-case remnants from the ddx must surely die.
- rename "Offset" to linear_offset, to make it clearer that on gen4+
this is only used by the hw for linear buffers, for tiled buffers it
uses the TILEOFF register.
- call DSAPADDR DSPLINOFF on gen4+ for the same reason (and because
the documentation really renamed the register).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While creating the new enable/disable_gt_powersave functions in
commit 8090c6b9da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 24 16:42:32 2012 +0200
drm/i915: wrap up gt powersave enabling functions
I've botched up the handling of ironlake_disable_rc6. Fix this up by
calling it at the right place. Note though that ironlake_disable_rc6
does a bit more than just disabling rc6 - it also tears down all the
allocated context objects.
Hence we need to move intel_teardown_rc6 out and directly call it from
intel_modeset_cleanup.
Also properly mark ironlake_enable_rc6 as static and kill the un-used
declaration in i915_drv.h.
Note: In review a question popped out why disable_rc6 also tears down
the backing object and why we should move that out - it's simply for
consistency with gen6+ rps code, which does it that way.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit moves force wake support routines into intel_pm modules, and
exports the gen6_gt_check_fifodbg routine (used in I915_READ).
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of calling each one for each generation indiviudally.
Notice that we've already managed to be inconsistent, the resume path
is missing an IS_VLV check. As a nice benefit we can mark all the
platform specific enable/disable functions as static and hide them in
intel_pm.c
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we switch on/off the primary plane if it is completely obscured by an
overlapping video sprite, we also nee to make sure that we update the
FBC configuration at the same time.
v2: Not all crtcs are intel_crtcs, as spotted by Daniel.
v3: Boot testing rules.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50238
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4+ we have a bitfield to specify from which pipe the backlight
controller should take it's clock. For PCH split platforms we've
already set these up, but only at initialization time. And without
taking into account the 3rd pipe added with ivb.
For gen4, we've completely ignored these. Although we do restrict lvds
to the 2nd pipe, so this is only a problem on machines where we boot
up with the lvds on the first pipe.
So restructure the code to enable the backlight on the right pipe at
modeset time.
v2: For odd reasons panel_enable_backlight gets called twice in a
modeset, so we can't WARN_ON in there if the backlight controller is
switched on already.
v3: backlight enable can also be called through dpms on, so the check
in there is legit. Update the comment to reflect that.
Tested-By: Kamal Mostafa <kamal@canonical.com>
Bugzilla: https://bugs.launchpad.net/bugs/954661
Cc: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.
After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.
Also mark the mode argument of pch_panel_fitting const.
v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.
The next patch will stop us from modifying mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a function that is able to fully 'set' the state of the DIP
registers to a known state.
Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.
This patch only adds the infrastructure keeping the code behavior the
same as before.
v2: add static keywords
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least the worst offenders:
- SDVO specifies that the encoder should compute the ecc. Testing also
shows that we must not send the ecc field, so copy the dip_infoframe
struct to a temporay place and avoid the ecc field. This way the avi
infoframe is exactly 17 bytes long, which agrees with what the spec
mandates as a minimal storage capacity (with the ecc field it would
be 18 bytes).
- Only 17 when sending the avi infoframe. The SDVO spec explicitly
says that sending more data than what the device announces results
in undefined behaviour.
- Add __attribute__((packed)) to the avi and spd infoframes, for
otherwise they're wrongly aligned. Noticed because the avi infoframe
ended up being 18 bytes large instead of 17. We haven't noticed this
yet because we don't use the uint16_t fields yet (which are the only
ones that would be wrongly aligned).
This regression has been introduce by
3c17fe4b8f is the first bad commit
commit 3c17fe4b8f
Author: David Härdeman <david@hardeman.nu>
Date: Fri Sep 24 21:44:32 2010 +0200
i915: enable AVI infoframe for intel_hdmi.c [v4]
Patch tested on my g33 with a sdvo hdmi adaptor.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25732
Tested-by: Peter Ross <pross@xvid.org> (G35 SDVO-HDMI)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.
Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.
This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_hdmi data structure and support functions to a shared location,
to allow their usage from intel_ddi module.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.
Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.
So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.
Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.
v2: simplify Haswell handling logic
v3: use generic function for handling digital outputs.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.
v2: improve comment as per Chris Wilson suggestion
v3: incorporate latest changes in specs.
v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Haswell, DDI ports can work in FDI mode to support
connectivity with the outputs located on the PCH.
This commit adds support for such connections in the intel_ddi module, and
provides Haswell-specific functionality to make it work.
v2: simplify the commit as per Daniel Vetter suggestion.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.
Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge of drm-next to resolve a few ugly conflicts and to get a few
fixes from 3.4-rc6 (which drm-next has already merged). Note that this
merge also restricts the stencil cache lra evict policy workaround to
snb (as it should) - I had to frob the code anyway because the
CM0_MASK_SHIFT define died in the masked bit cleanups.
We need the backmerge to get Paulo Zanoni's infoframe regression fix
for gm45 - further bugfixes from him touch the same area and would
needlessly conflict.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every time we use the device after a period of idleness, check that the
power management setup is still sane. This is to workaround a bug
whereby it seems that we begin suppressing power management interrupts,
preventing SandyBridge+ from going into turbo mode.
This patch does have a side-effect. It removes the mark-busy for just
moving the cursor - we don't want to increase the render clock just for
the sprite, though we may want to bump the display frequency. I'd argue
that we do not, and certainly don't want to take the struct_mutex here
due to the large latencies that introduces.
References: https://bugs.freedesktop.org/show_bug.cgi?id=44006
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They require an AVI InfoFrame with a proper Pixel Repetition field.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To keep the consistency with the other fields.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're now in intel_pm.c, so group them a bit better.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have a nice home for power management code, so let's use it!
v2: Resolve conflict agains "Only enable IPS polling for gen5"
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PCH PLLs aren't required for outputs on the CPU, so we shouldn't just
treat them as part of the pipe.
So split the code out and manage PCH PLLs separately, allocating them
when needed or trying to re-use existing PCH PLL setups when the timings
match.
v2: add num_pch_pll field to dev_priv (Daniel)
don't NULL the pch_pll pointer in disable or DPMS will fail (Jesse)
put register offsets in pll struct (Chris)
v3: Decouple enable/disable of PLLs from get/put.
v4: Track temporary PLL disabling during modeset
v5: Tidy PLL initialisation by only checking for num_pch_pll == 0 (Eugeni)
v6: Avoid mishandling allocation failure by embedding the small array of
PLLs into the device struct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44309
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (up to v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3+)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds intel_pm routine for generic power-related infrastructure
initialization.
v2: now that all the platform-specific stuff is initialized in one place, we
can also add back the static definitions to platform-specific functions which
we abstract now.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moves the clock gating-related functions into intel_pm module.
Also, please note that we do change the function type from static to
non-static in this patch for the move, to prevent breaking bisecting with
non-working intermediate commit. Those are returned back to static form in
the following patch which setups a generic PM initialization function,
which was split into a different one to simplify review.
v2: rebase on top of latest drm-intel-next-queued to incorporate all the
changes that went there meanwhile.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moves DRPS, RPS and RC6-related functionality into intel_pm module.
It also removes the linux/cpufreq.h include from intel_display, as its
only user was the GPU turbo-related functionality in Gen6+ code path.
v2: rebase on top of latest drm-intel-next-queued adding the bits that
shifted around since the last patch.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit moves Frame Buffer Compression-related operations and support
functions into the new intel_pm module.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than export every single architecture specific update_wm, just
export the wrapper around the display vtable.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This regression has been introduced in
commit ca9bfa7eed
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
Looking at hibernate overwriting I though it looked like a cursor,
so I tracked down this missing piece to stop the cursor blink
timer. I've no idea if this is sufficient to fix the hibernate
problems people are seeing, but please test it.
Both radeon and nouveau have done this for a long time.
I've run this personally all night hib/resume cycles with no fails.
Reviewed-by: Keith Packard <keithp@keithp.com>
Reported-by: Petr Tesarik <kernel@tesarici.cz>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reported-by: Lots of misc segfaults after hibernate across the world.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=37142
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Bojan Smojver <bojan@rexursive.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus. Add simple indirect register access
routines to get to those registers.
v2: move new wait_for macro to intel_drv.h (Ben)
fix DPIO_PKT double write (Ben)
add debugfs file
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With valleyview we'll have these at yet another address, so keeping
track of this with an ever-growing list of registers will get ugly.
This way intel_sdvo.c is fully independent of the base address of the
output ports display register blocks.
While at it, do 2 closely related cleanups:
- use SDVO_NAME some more
- change the sdvo_reg variables to uint32_t like other registers.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to correctly account for reserving space in the GTT and fences
for a batch buffer, we need to independently track whether the fence is
pinned due to a fenced GPU access in the batch or whether the buffer is
pinned in the aperture. Currently we count the fenced as pinned if the
buffer has already been seen in the execbuffer. This leads to a false
accounting of available fence registers, causing frequent mass evictions.
Worse, if coupled with the change to make i915_gem_object_get_fence()
report EDADLK upon fence starvation, the batchbuffer can fail with only
one fence required...
Fixes intel-gpu-tools/tests/gem_fenced_exec_thrash
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Paul Neumann <paul104x@yahoo.de>
[danvet: Resolve the functional conflict with Jesse Barnes sprite
patches, acked by Chris Wilson on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we have a few places where the drm drivers would like to sleep to
be nice to the system, mainly in the modesetting paths, but we also
have two cases were atomic modesetting must take place, panic writing
and kernel debugger. So provide a central inline to determine if a
sleep or delay should be used and use this in the intel and radeon drivers.
v2: drop intel_drv.h MSLEEP macro, nobody uses it.
Based on patch from Michel Dänzer <michel.daenzer@amd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43941
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add new ioctls for getting and setting the current destination color
key. This allows for simple overlay display control by matching a color
key value in the primary plane before blending the overlay on top.
v2: remove unnecessary mutex acquire/release around reg accesses
v3: add support for full color key management
v4: fix copy & paste bug in snb_get_colorkey
don't bother checking min/max values against docs as the docs are likely
wrong (how could we handle 10bpc surface formats?)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
To save power when the sprite is full screen, we can disable the primary
plane on the same pipe. Track the sprite status and enable/disable the
primary opportunistically.
v2: remove primary plane enable/disable hooks; they're identical
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The video sprites support various video surface formats natively and can
handle scaling as well. So add support for them using the new DRM core
sprite support functions.
v2: use drm specific fourcc header and defines
v3: address Daniel's comments:
- don't take struct mutex around register access (only needed for
regs in the GT power well)
- don't hold struct mutex across vblank waits
- fix up update_plane API (pass obj instead of GTT offset)
- add interlaced defines for sprite regs
- drop unnecessary 'reg' variables
- comment double buffered reg flushing
Also fix w/h confusion when writing the scaling reg.
v4: more fixes, address more comments from Daniel, and include Hai's fix
- prevent divide by zero in scaling calculation (Hai Lan)
- update to Ville's new DRM_FORMAT_* types
- fix sprite watermark handling (calc based on CRTC size, separate
from normal display wm)
- remove private refcounts now that the fb cleanups handles things
v5: add linear surface support
v6: remove color key clearing & setting from update_plane
For this version, I tested DPMS since it came up in the last review;
DPMS off/on works ok when a video player is working under X, but for
power saving we'll probably want to do something smarter. I'll leave
that for a separate patch on top. Likewise with the refcounting/fb
layer handling, which are really separate cleanups.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
Some active adaptors (VGA usually) only have two lanes at 2.7GHz.
That's a maximum pixel clock of 144MHz at 8bpc, but 192MHz at 6bpc.
Fixes Asus UX31 panel being black at startup due to no valid modes since
dc22ee6fc1.
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
To properly support the various plane formats supported by different
hardware, the kernel must know the pixel format of a framebuffer object.
So add a new ioctl taking a format argument corresponding to a fourcc
name from the new drm_fourcc.h header file. Implement the fb creation
hooks in terms of the new mode_fb_cmd2 using helpers where the old
bpp/depth values are needed.
v2: create DRM specific fourcc header file for sharing with libdrm etc
v3: fix rebase failure and use DRM fourcc codes in intel_display.c and
update commit message
v4: make fb_cmd2 handle field into an array for multi-object formats
pull in Ville's fix for the memcpy in drm_plane_init
apply Ville's cleanup to zero out fb_cmd2 arg in drm_mode_addfb
v5: add 'flags' field for interlaced support (from Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
SPD frames are actually type 0x83, not just 0x3.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
At the point where we check, we can't do much about the failure, but it
can aid debugging. Note that the auto-train override bit will be reset
as part of normal mode setting with this patch if a pipe ever does get
stuck, but that's consistent with the workaround for CPT provided by the
hardware team. This patch helped catch the fact that the pipe wasn't
running in the !composite sync FDI case on my IVB SDV, so has already
shown to be useful.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add two new fields to the intel_crtc struct for 3 pipe support: no_pll
and use_pll_a. The no_pll field is only set on the 3rd pipe to indicate
that it doesn't have a PLL of its own and so shouldn't try to write the
main PLL regs. The use_pll_a field controls which PLL pipe 3 will
share, A or B. The core code will try to share PLLs with whichever pipe
has the same timings, rejecting the mode set if none is found. This
means that pipe 3 must always be set after one of the other pipes has
been configured with real PLL settings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
I was seeing a nasty 5 frame glitch every 10 seconds, caused by the
poll for connection on DVI attached by SDVO.
As my SDVO DVI supports hotplug detect interrupts, the fix is to
enable them, and hook them in to the various bits of driver
infrastructure so that they work reliably.
Note that this is only tested on single-function DVI-D SDVOs, on two
platforms (965GME and 945GSE), and has not been checked against a
specification document.
With lots of help from Adam Jackson <ajax@redhat.com> on IRC.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add ELD support for Intel Eaglelake, IbexPeak/Ironlake,
SandyBridge/CougarPoint and IvyBridge/PantherPoint chips.
ELD (EDID-Like Data) describes to the HDMI/DP audio driver the audio
capabilities of the plugged monitor. It's built and passed to audio
driver in 2 steps:
(1) at get_modes time, parse EDID and save ELD to drm_connector.eld[]
(2) at mode_set time, write drm_connector.eld[] to the Transcoder's hw
ELD buffer and set the ELD_valid bit to inform HDMI/DP audio driver
This patch is tested OK on G45/HDMI, IbexPeak/HDMI and IvyBridge/HDMI+DP.
Test scheme: plug in the HDMI/DP monitor, and run
cat /proc/asound/card0/eld*
to check if the monitor name, HDMI/DP type, etc. show up correctly.
Minor imperfection: the GEN5_AUD_CNTL_ST/DIP_Port_Select field always
reads 0 (reserved). Without knowing the port number, I worked it around
by setting the ELD_valid bit for ALL the three ports. It's tested to not
be a problem, because the audio driver will find invalid ELD data and
hence rightfully abort, even when it sees the ELD_valid indicator.
Thanks to Zhenyu and Pierre-Louis for a lot of valuable help and testing.
CC: Zhao Yakui <yakui.zhao@intel.com>
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
CC: Jeremy Bush <contractfrombelow@gmail.com>
CC: Christopher White <c.white@pulseforce.com>
CC: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
CC: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Tested-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes it easier to add support for other infoframes (e.g. SPD,
vendor specific).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
In order to accommodate the requirements of re-enabling FBC after
page-flipping, but to avoid doing so and incurring the cost of a wait
for vblank in the middle of a page-flip sequence, we defer the actual
enablement by 50ms. If any request to disable FBC arrive within that
interval, the enablement is cancelled and we are saved from blocking on
the wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Figuring out which pipe bpp to use is a bit painful. It depends on both
the encoder and display configuration attached to a pipe. For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering. But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.
So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.
Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ring frequency scaling table tells the PCU to treat certain GPU
frequencies as if they were a given CPU frequency for purposes of
scaling the ring frequency. Normally the PCU will scale the ring
frequency based on the CPU P-state, but with the table present, it will
also take the GPU frequency into account.
The main downside of keeping the ring frequency high while the CPU is
at a low frequency (or asleep altogether) is increased power
consumption. But then if you're keeping your GPU busy, you probably
want the extra performance.
v2:
- add units to debug table header (from Eric)
- use tsc_khz as a fallback if the cpufreq driver doesn't give us a freq
(from Chris)
v3:
- fix comments & debug output
- remove unneeded force wake get/put
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Make the audio property creation routine common and share the single
property between the connectors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Ibex Peak and CougarPoint already require a different setting (added
here), and future chips will likely follow that precedent.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We need to ensure that we feed valid memory into the display plane
attached to the pipe when switching the pipe on. Otherwise, the display
engine may read through an invalid PTE and so throw an PGTBL_ER
exception.
As we need to perform load detection before even the first object is
allocated for the fbdev, there is no pre-existing object large enough
for us to borrow to use as the framebuffer. So we need to create one
and cleanup afterwards. At other times, the current fbcon may be large
enough for us to borrow it for duration of load detection.
Found by assert_fb_bound_for_plane().
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
i915 calls the panic handler function on last close to reset the modes,
however this is a really bad idea for multi-gpu machines, esp shareable
gpus machines. So add a new entry point for the driver to just restore
its own fbcon mode.
v2: move code into fb helper, fix panic code to block mode change on
powered off GPUs.
[airlied: this hits drm core and I wrote it and it was reviewed on intel-gfx
so really I signed it off twice ;-).]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
During modesetting, we need to wait for the hardware to report
readiness by polling the registers. Normally, we call msleep() between
reads, because some state changes may take a whole vblank or more
to complete. However during a panic, we are in an atomic context and
cannot sleep. Instead, busy spin polling the termination condition.
References: https://bugzilla.kernel.org/show_bug.cgi?id=31772
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In order to prevent "crushed blacks" on TVs, the range of the RGB output
may be limited to 16-235. This used to be available through Xorg under
the "Broadcast RGB" option, so reintroduce support for KMS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34543
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The code paths for modesetting are growing in complexity as we may need
to move the buffers around in order to fit the scanout in the aperture.
Therefore we face a choice as to whether to thread the interruptible status
through the entire pinning and unbinding code paths or to add a flag to
the device when we may not be interrupted by a signal. This does the
latter and so fixes a few instances of modesetting failures under stress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
Share the lid detection code for the all panels for consistent behaviour
and a single place to add the eventual quirks for crap hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The automatic powersaving feature is once again causing havoc, with 100%
reliable hangs on boot and resume on affected machines.
Reported-by: Francesco Allertsen <fallertsen@gmail.com>
Reported-by: Gui Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Add an interrupt handler for switching graphics frequencies and handling
PM interrupts. This should allow for increased performance when busy
and lower power consumption when idle.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... otherwise the panel-fitter may be left enabled with random settings
and cause unintended filtering (i.e. blurring of native modes on external
panels).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31942
Reported-and-tested-by: Ben Kohler <bkohler@gmail.com>
Tested-by: Ciprian Docan <docan@eden.rutgers.edu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes issue where i915_gfx_val was reporting values several
orders of magnitude higher than physically possible (without
leaving scorch marks on my thighs at least.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we set the output type of PCH attached eDP panels to
INTEL_OUTPUT_eDP this function would never return true when it should.
It's been replaced by working functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display code needs to distinguish between CPU and PCH attached eDP
panels, so add some helpers to handle that.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ensures that we do wait upon the flushes to complete if necessary
and avoid the visual tears, whilst enabling pipelined page-flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When separating out the prepare/commit into its own separate functions
we overlooked that the intel_crtc->dpms_mode was being used elsewhere to
check on the actual status of the pipe.
Track that bit of logic separately from the actual dpms mode, so there
is no confusion should we be able to handle multiple dpms modes, nor
any semantic conflict between prepare/commit and dpms.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This closes a couple of corner cases where we introduced and forgot
about a couple of routines that need to be called when disabling the
crtc and then re-enabling it. The code needs to be moved again so that
the common bits are shared across generations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 77d07fd9d7 introduced a regression
where by not waiting for the panel to be turned off, left the panel and
PLL registers locked across the modeset. Thus the panel remaining blank.
As pointed out by Daniel Vetter, when testing LVDS it helps to open the
laptop and look at the actual panel you are purporting to test.
A second issue with the patch was that in order to modify the panel
fitter before gen5, the pipe and the panel must have be completely
powered down. So we wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid a potentially long busy-wait if we not in the process of
atomically switching to the kdb console.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently we have a exact mapping of a connector onto an encoder for its
whole lifetime. Make this an explicit property of the structure and so
simplify the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Why iterate all the crtcs to find the pipe, when we already know which
crtc is attached to which pipe?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.
Fixes:
Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
https://bugs.freedesktop.org/show_bug.cgi?id=29716
And a bug on one of my PineView boxes which overflowed the backlight
value.
Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
During DPMS we currently do not want the overlay code to be
interruptible, so pass that information down and only take the
uninterrruptible paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can program the h/w to first wait on the flip and then switch off
without relying on s/w intervention. This removes the need for a double
step switch off, bringing much rejoicing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scoping of the validity of the mapping is thus clarified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
wait_for() uses msleep() to yield the cpu whilst spinning waiting for a
register to change. kdb asserts that mode changes are atomic and so
prohibits msleep. The alternative would be to use mdelay or to simply
probe the register more often instead of busy waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Jesse's feedback from using the wait_for() macro was that the msleep
argument was that it was superfluous and made the macro more difficult
to use and to read. As the actually amount of time to sleep is not
critical, the crucial part is to sleep and let the processor schedule
something else whilst we wait for the event, replace the argument with a
hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).
This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead. Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The i845 and i865 have a peculiarlity in that CURBASE is not the trigger
for the vsync update of the cursor registers but instead the
modification of that register is prohibited whilst the cursor is
enabled. Reorder the write sequence for CURPOS, CURCNTR and CURBASE on
i845 to i865 to match.
v2: Remove the checks for i845/i865 from within i9xx_cursor_update()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a new macro, wait_for, to simplify the act of waiting on a register
to change state. wait_for() takes three arguments, the condition to
inspect on every loop, the maximum amount of time to wait and whether to
yield the cpu for a length of time after each check.
v2: Upgrade failure messages to DRM_ERROR on the suggestion of
Eric Anholt. We do not expect to hit these conditions as they reflect
programming errors, so if we do we want to be notified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
v2: Hook in DP paths to keep FULLSCREEN panel fitting on eDP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The comments have long desired that we should switch off the cursor
along with the display plane, make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make the code that tiny bit clearer by reducing the pointer dance.
2 files changed, 130 insertions(+), 147 deletions(-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Subclass intel_encoder to reduce the pointer dance through
intel_encoder->dev_priv.
10 files changed, 896 insertions(+), 997 deletions(-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The docs warn that to position the cursor such that no part of it is
visible on the pipe is an undefined operation. Avoid such circumstances
upon changing the mode, or at any other time, by unsetting the cursor if
it moves out of bounds.
"For normal high resolution display modes, the cursor must have at least a
single pixel positioned over the active screen.” (p143, p148 of the hardware
registers docs).
Fixes:
Bug 24748 - [965G] Graphics crashes when resolution is changed with KMS
enabled
https://bugs.freedesktop.org/show_bug.cgi?id=24748
v2: Only update the cursor registers if they change.
v3: Fix the unsigned comparision of x,y against width,height.
v4: Always set CUR.BASE or else the cursor may become corrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Christian Eggers <ceggers@gmx.de>
Cc: Christopher James Halse Rogers <chalserogers@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
This makes them sort to the front in X, which makes them likely to be
the primary outputs if you haven't specified a preference in your DE,
which is likely to be what you want.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This one adds support for eDP that connected on PCH DP-D port
instead of CPU DP-A port, and only DP-D port could be used for eDP.
https://bugs.freedesktop.org/show_bug.cgi?id=27220
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Templar <templar@rshc.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.
v2: Add Sandybridge support, fix obvious math error.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As all display drivers have been converted, remove the left reference
for connector object in old structure.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.
It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Jesse Barnes