Merge mt76x0_dev data structure in mt76x02_dev one and remove
duplicated code. Remove unused definition in mt76x0.h.
Moreover merge mt76x0_caldata and mt76x02_rx_freq_cal data structures.
This is a preliminary patch for rxwi unification.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_dev in mt76x02_util.h and rename it in mt76x02_dev
in order to be shared between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove hw_atomic_mutex mutex in mt76x0_dev data structure
since mt76x0_phy_set_channel is already protected by mt76_dev
mutex while mt76x0_chip_onoff is used just at device probe or
cleanup
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove no longer used mac_lock spinlock and data array
in mt76x0_dev data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use shared mt76x02 utility routines for rssi tracking.
Moreover remove no longer used con_mon_lock spinlock
and following variable:
- ap_bssid
- bcn_freq_off
- bcn_phy_mode
- avg_rssi
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_rx_get_sta and mt76x02_rx_get_sta_wcid utility routines in
mt76x02-lib module since it will be used by mt76x0 driver in order to
unify rxwi parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_get_min_avg_rssi in mt76x02-lib module since
it will be used by mt76x0 driver in order to unify rxwi parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02u_tx_prepare_skb routine to fill txwi in mt76x2u and
mt76x0u driver and remove duplicated code. Moreover add static
qualifier to mt76x02_mac_tx_rate_val and mt76x02_mac_fill_txwi
routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_write_txwi in mt76x02_mac.c since it is shared between
mt76x0 and mt76x2 drivers. This is a preliminary patch to unify txwi
configuration between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add get_tx_txpwr_adj function pointer to mt76_driver_ops data structure
as a preliminary patch to unify txwi configuration between mt76x0 and
mt76x2 drivers since tpc is currently supported just by mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx_get_max_txpwr_adj routine in mt76x02-lib module
since now both mt76x0 and mt76x2 drivers read rate tx power gain from
rate_power data structure. Moreover remove get_max_txpwr_adj function
pointer from mt76_driver_ops data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stop mac and calibration work stopping the hw even if the
device has been removed
Fixes: b11e19694d ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76u_alloc_queues need to be called before mt76u_mcu_init_rx
since it initializes rx_page_lock spinlock used in mt76u_buf_alloc
routine.
Fixes: b11e19694d ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is correct fix for c12128ce44 ("mt76: use a per rx queue page
fragment cache"). We use wrong length when we allocate segments for
MCU transmissions, which require bigger segment size than e->buf_size.
Commit 481bb04324 ("mt76: usb: make rx page_frag_cache access atomic")
partially solved the problem or actually mask it by changing
mt76u_mcu_init_rx() and mt76u_alloc_queues() sequence, so e->buf_size
become non zero any longer, but still not big enough to handle MCU data.
Patch fixes memory corruption which can manifest itself as random,
not easy to reproduce crashes, during mt76 driver load or unload.
Fixes: c12128ce44 ("mt76: use a per rx queue page fragment cache")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The header guards that are #defined are different from those being
checked. Fix this by #defining them to the correct name.
Fixes clang warnings:
drivers/net/wireless/mediatek/mt76/mt76x02_mcu.h:17:9:
warning: '__MT76x02_MCU_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]
drivers/net/wireless/mediatek/mt76/mt76x02_usb.h:17:9:
warning: '__MT76x02_USB_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]
Fixes: 905db74701 ("mt76: usb: move mt76x02 mcu code in mt76x02-usb module")
Fixes: edaa580bc8 ("mt76: move shared mcu_calibrate routine in mt76x02-lib module")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2 and mt76x2u drivers to mt76x2 subfolder and
leave just shared code in mt76 root folder
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0e_cleanup routine to tidy up the device
during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command responses and events from the firmware are copied twice in
control path: at first in shm core (qtnf_shm_handle_new_data) and
then in pcie bus drivers (qtnf_pcie_control_rx_callback). There
is no need to copy this data twice, it can be done only once
in rx callbacks.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Notify firmware to flush cache before scanning when needed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several members of pwr-MAC structure are re-initialized several times
together with per-VIF initialization. Fix that and simplify the code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
variable 'wl' set but not used [-Wunused-but-set-variable]
After commit 644aa4d620 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* tx power configuration fix for 76x2
* more progress on mt76x0e support
* support for getting firmware version via ethtool
* fix for rx buffer allocation regression on usb
* fix for handling powersave responses
* fix for mt76x2 beacon transmission
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAluyBLsACgkQ130UHQKnbvVy7wCeN1zcfGDCAZulOwND9+wO6P7d
/ZEAoKPedreI+0u+DJ5w6H8cZR6THGxb
=MYwe
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-10-01' of https://github.com/nbd168/wireless
mt76 patches for 4.20
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* tx power configuration fix for 76x2
* more progress on mt76x0e support
* support for getting firmware version via ethtool
* fix for rx buffer allocation regression on usb
* fix for handling powersave responses
* fix for mt76x2 beacon transmission
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbsgclAAoJEG4XJFUm622bAJ0H/A53eluDpiA6cT2tbThQn/jC
+t9DH6EMR4WpYaBEFZtfbZxgrow2bdbllrfrcq22U8Z9BTg875MunJAureEG8Rkn
mBowkuu/RESOO00JXTuqvGcTP+1oaaETEdyABzQFI3uCDyEF9vGCJwNODtyQ5Rch
JYFVDJhWYm1K84jTCDX1x9izEKxf1PaQobh8JqZnvNG0QOIDpT6y/T5RGhUL9nTr
aRuGDa9ap4RFocq1t0eVqx/NliXOHuEbO58E6rMm9DiSujmf1Wa/tndNXGxGWk/N
X8KCz619Syr3v/lF6gXWwmsHt5TBh+peKajUsVY9wJUYkBFTOzVjy0ucYCr67yA=
=HZJ3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.19
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes: d9c52fd17c ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_hw_diag_fast_download() generally has good boundary checking, but
it misses verifying that the next metadata header actually fits in the
remaining buffer space. Add such a check.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FFT max index retrieval was not retrieved correctly for HT20/HT40 FFT
frames. Fixing the retrieval allows us to remove the fixup function as
well. While at it, split the spectral_max_index function into versions
for ht20 and ht40 to simplify the code.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the loop break like this, there are false "FFT report truncated"
messages because the iterator is not advanced as the check expects.
Instead, just return, for a single frame there is nothing left to be
done anyways.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful to see whether spectral samples get discarded.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlutzKgACgkQoUecoho8
xfpv7g//fhLx4xvYl2i5sVhk+FcYCEUcyYiVO4wrXdmdNafobuJRaMuxuUuagExE
J+wsQmSt3LribOGQB06aa/Lf+d5FyKpD8Qcs3ZY2WX5OlLRN1EczNoiTXKfE0E1D
d0a80IjD2EeqhhU9D/7DTBsN7zCpJEW5otJ4S9WY0Y/MKHSFyiDcoqnx4H1ZAv5N
WH8cvTjGf4tPjkjuuEPLlVhz65hqNsM1A+VaZCU21SOlc8ihSXSAt1h8AMnWLPLz
MHxzMbnjWPN8qjgKacEy7ETP14iCjTryRsXBWt48A+XZYyUQFNcnjFVME5KyOB6V
YkHb8EQSkjHOWg4eutOJijNPBHLxQDFHY6LdOZ3JEmqtOKPt+A82JwXmBq6Ez4O4
DobrAEvDwnBMFhNoboNA9C0/B57j9+FPkgd0a8Y98Rr28SBYbnmK8wlZVRWU0S/9
WRg0pafzmCh1hcYedLWfGFkNio9ZZqfhLOWdVpaobJkE47gDLx3aoyXx7UK4VSfG
kIigRccQsOYfOUNvQM8f/J2/uzy1TfkM7E4PaU6Q6lIhfjDuWPzGY7SpuwpSd1hf
qu1EB4EwRiOdvwc/EiLJpsrMSNe9m1EWIopfas0x1dallOSC1bNIRTh2o4oN3a3V
vcvtTIwST5C5IvMeZOFR2xmqArypWlEjvE2ieuq8RtMZnMaq1Rk=
=5Y2V
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-09-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches for 4.20
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that wifi device is of supported variant by checking it's CHIP ID
before completing a probe sequence.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Waiting for "completion" to be set in FW load thread can not be used
in case PCIe remove is called before FW load work was scheduled.
Just wait for work completion instead to avoid problems.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extract platform-independent PCIe driver code into a separate file, and
use it from platform-specific modules.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A few include directives were missing in bus.h resulting in dependency
of include order in other modules. Add missing includes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename several functions to indicate that they are platform specific.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move platform-independent PCIe data structure to a separate header file
so it can be reused by different devices.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
tx_lock name will later be reused when common pcie code is extracted to
separate files.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to extract common PCIe driver state, indicate
PEARL-specific structures by their name and move them to pearl-specific
source file.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to extract common pcie driver state into a separate
structure, rename Pearl-specific state to qtnf_pcie_pearl_state and move
it directly to pearl-specific PCIe source file.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to extract common qtnfmac PCIe driver sources into a
separate file, move existing Pearl-specific pcie driver sources to pcie/
directory.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name is only needed at probe stage, no point in keeping it in
driver state structure.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement custom rt2800mmio flush routine and change txstatus
routine to read TX_STA_FIFO also in the tasklet.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use different tx status timeouts for normal operation and when flushing.
This increase timeout to 2s for normal operation as when there are bad
radio conditions and frames are reposted many times device can not provide
the status for quite long. With new timeout we can still get valid status
on such bad conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not check for tx status timeout everytime we perform txstatus tasklet.
Perform check once per half a second.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use usb txdone/txstatus routines (now in rt2800libc) for mmio devices.
Note this also change how we handle INT_SOURCE_CSR_TX_FIFO_STATUS
interrupt. Now it is disabled since IRQ routine till end of the txstatus
tasklet (the same behaviour like others interrupts). Reason to do not
disable this interrupt was not to miss any tx status from 16 entries
FIFO register. Now, since we check for tx status timeout, we can
allow to miss some tx statuses. However this will be improved in further
patch where I also implement read status FIFO register in the tasklet.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to reuse usb txdone/txstatus routines for mmio, move them
to common rt2800lib.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_PCI;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_USB;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN;
~ ^~~~~~~~~~~~~~~~
3 warnings generated.
Use the values from the correct enumerated type, wifionly_chip_interface.
BTC_INTF_UNKNOWN = WIFIONLY_INTF_UNKNOWN = 0
BTC_INTF_PCI = WIFIONLY_INTF_PCI = 1
BTC_INTF_USB = WIFIONLY_INTF_USB = 2
Link: https://github.com/ClangBuiltLinux/linux/issues/135
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/wireless/ath/ath5k/debug.c:1031:14: warning: address of
array 'ah->sbands' will always evaluate to 'true'
[-Wpointer-bool-conversion]
BUG_ON(!ah->sbands);
~~~~~^~~~~~
./include/asm-generic/bug.h:61:45: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~
./include/linux/compiler.h:77:42: note: expanded from macro 'unlikely'
# define unlikely(x) __builtin_expect(!!(x), 0)
^
1 warning generated.
Given that this condition is always false because of the logical not,
just remove it.
Link: https://github.com/ClangBuiltLinux/linux/issues/130
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/net/wireless/rsi/rsi_91x_mac80211.c:927:50: warning: address of
array 'key->key' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (vif->type == NL80211_IFTYPE_STATION && key->key &&
~~ ~~~~~^~~
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/136
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: remove
extraneous parentheses around the comparison to silence this warning
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~ ^ ~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: use '=' to
turn this equality comparison into an assignment
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/134
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/pm.c: In function 'wil_suspend_keep_radio_on':
drivers/net/wireless/ath/wil6210/pm.c:193:16: warning:
variable 'start' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'fops_dump_nfcal' is not used since commit 4447d815fd ("ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let user can reset station airtime status by debugfs, it will
reset all airtime deficit to ATH_AIRTIME_QUANTUM and reset rx/tx
airtime accumulate to 0.
Signed-off-by: Louie Lu <git@louie.lu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE buffers are cleaned up prior to napi disable and this is causing
NULL pointer dereference due to "use after free".
Disable napi before resource cleanup to avoid "use after free".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is unbalanced napi_{enable,disable}() behavior as they
are being called from hif_snoc_{power_up/stop).
The fix is to call napi_enable() from ath10k_snoc_hif_start()
so that it matches with napi_disable() being called from
ath10k_snoc_hif_stop().
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the latest firmware design, the beacon interval should be
greater than 100 to bring the multiple vaps.
Set beacon_int_min_gcd to 100, when the wmi service
WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT is enabled
in the firmware. If not, beacon_int_min_gcd will be set
to the default value 1.
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00015
Tested in QCA9888 with firmware ver 10.4-3.5.1-0005
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.
Chipsets Tested : QCA988X, QCA9887, QCA9984
FW Tested : 10.2.4-1.0-41, 10.4-3.6.104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw_params value will only be used if it was explicitly set in the
global hw_params array.
This makes it possible to have the num_peers member unset.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 9d5804662c ("ath10k: retrieve MAC address from system
firmware if provided"), we support pulling our MAC address from system
firmware. Along with this, we should admit that it's possible for system
firmware to be screwed up as well, omitting the MAC address there.
Provide a fallback, such that we choose a randomly-generated MAC
address, with the local assignment bit set.
This is not a preferred mode of operation and really should only serve
the purpose of keeping the system chugging along while someone figures
out what's wrong with the system. Grepping through other wireless
drivers shows very similar fallback logic though, so why not?
git grep eth_random_addr drivers/net/wireless/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx_status for management frames is being filled
incorrectly in the flags of skb_cb. This incorrect
flag setting causes the upper layers to consider that
the particular frame was not transmitted properly,
leading to improper behavior.
Set the IEEE80211_TX_STAT_ACK flag in the info flags
of skb_cb, to indicate the successful transmission of
the management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: dc405152bb
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the first virtual interface is a station (or an AP with beacons
temporarily disabled), the beacon of the second interface needs to
occupy hardware beacon slot 0.
For some reason the beacon index was incorrectly masked with the
virtual interface beacon mask, which prevents the secondary
interface from sending beacons unless the first one also does.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ps-poll response frames can be sent via drv_tx. Store the frame sequence number
for such frames, in case a BlockAckReq needs to be sent
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware station lookup for pspoll frames can fail, which makes the driver
ignore ps-poll frames. Fix the resulting powersave issues by looking up
the station for pspoll frames in software
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x0u_tx_prepare_skb routine in usb module in
order to remove leftover usb dependency from generic code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Read eeprom data from mtd memory by default and fall-back
to efuse if it fails
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76x0e_start and mt76x0e_stop mac80211
callbacks to start/stop device mac opening/closing
the netdevice
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add ieee80211_ops ops pointer to mt76x0_alloc_device routine signature
in order to specify mac80211 callbacks and remove usb dependency from
mt76x0 generic code.
Move mt76x0_ops callbacks in usb module in order to remove leftover
usb dependency in mt76x0 generic code.
Introduce mt76x0e_ops mac80211 callbacks for pci code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in
mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers.
Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data
structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x0_ant_select routine in __mt76x0_phy_set_channel in order to
configure antenna parameters according to the current wireless channel
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0e_register_device routine in pci.c
to initialize the device during hw probe.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move usb initialization code in mt76x0-usb module in
order to remove usb dependency from generic init code
(not completed yet). Moreover fix a memory leak in usb probe
if mt76x02_wait_for_mac fails
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76x02_mac_start since the mac start code is shared between
mt76x0e and mt76x2 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize rxfilter mask at bootstrap an not at mac start.
This is a preliminary patch to share mt76x2_mac_start routine
between mt76x2e and mt76x0e drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove MT_PBF_SYS_CTRL configuration in mt76x0_reset_csr_bbp since
it is already initialized in mt76x0_init_mac_registers routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove MT_HEADER_TRANS_CTRL_REG/MT_TSO_CTRL configuration
since they are already initialized in mt76x0_init_mac_registers
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_wait_for_wpdma and mt76x02_wait_for_txrx_idle
utility routines in mt76x0_init_hardware and mt76x0_mac_start
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move usb mcu code in a dedicated source file in order to remove
usb dependency from generic source files and improve code
maintainability
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move pci mcu code in a dedicated source file in order to
improve maintainability and facilitate new device support
development
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mac/rf/dcoc initial values to latest version of vendor driver.
Improve code readability
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_wait_for_bbp utility routine in mt76x02_util.h
in order to be resued by mt76x0 driver. Morover rename it in
mt76x02_wait_for_txrx_idle
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mmio implementation of mt76_mmio_rd_rp and
mt76_mmio_wr_rp and remove mt76x2 duplicated code.
mt76_mmio_{wr,rd}_rp allows to reuse mt76x0 init code
adding mt76x0e support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_beacon_offset utility routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 driver and remove
duplicated code. Moreover move beacon_offset data structure in
mt76x02-lib module since it is shared between mt76x0 and mt76x2
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_dma_init, mt76x02_init_rx_queue and mt76x02_init_tx_queue
routines in mt76x02-lib module in order to be reused by mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_set_irq_mask, mt76x02_irq_enable and mt76x02_irq_disable
in mt76x02-lib module in order to be reused by mt76x0 driver.
Moreover move irq_lock and irqmask in mt76_mmio data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76x02_dma_enable and mt76x02_dma_disable utility routines
in order to be reused in mt76x0 mac configuration and remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move wait_for_wpdma utility routine in mt76x02_dma.h
in order to be reused by mt76x0 driver. Moreover add
the possibility to specify the timeout value in
wait_for_wpdma signature
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_poll utility routine in mt76x0_set_wlan_state to check
if the PLL/XTAL is ready
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the WLAN core is still active during initialization, it might cause
the MCU or DMA to hang. This can happen during soft reboot, so disable
the core + clock early to avoid this issue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-LINK Archer T1U do not support 2.4GHz band despite EEPROM
reports that. Add quirk to mask out 2.4GHz support.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 uses __skb_pad() with free_on_error set to true, this is the same
as calling skb_pad().
This patch does not change any functionality, but it makes it easier to
backport this driver in backports, because skb_pad() is also available
in older kernel versions.
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
print fw_ver and build_ver members of struct mt76x02_fw_header, similarly
to what appears in the output of 'dmesg' when the MCU firmware is loaded.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 shared debugfs implementation and remove duplicated code
in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0_extra_power_over_mac and mt76x0_phy_set_tx_power routines
since they are not actually used and tx power handling will be unified
with mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_rate_power_val and mt76x2_sign_extend_optional utility
routines in mt76x02_eeprom.h in order to reuse them in mt76x0 eeprom
parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move rate_txpower handler in mt76 debugfs in order to be reused
in mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_phy_set_txpower utility routine in mt76x02_phy.c
in order to be reused in mt76x0 tx power management code.
Moreover move following routines in mt76x02-lib module:
- mt76x02_tx_power_mask
- mt76x02_get_max_rate_power
- mt76x02_limit_rate_power
- mt76x02_add_rate_power_offset
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_rate_power data structure from mt76x2_dev to mt76_dev in order
to share it with mt76x0 driver. Moreover move txpower_conf and
txpower_cur in mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We need to return bool value in mt76x02_wait_for_mac.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 2735a6dd7d ("mt76: unify wait_for_mac")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove not useful WARN_ON macros in mt76u_get_rx_entry_len routine
since corrupted frames should just be silently discarded
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_tssi_enabled and mt76x02_temp_tx_alc_enabled in
mt76x02_eeprom.h in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify parse hw capabilities with mt76x2 driver using
mt76x02_eeprom_parse_hw_cap utility routine available
in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_eeprom_parse_hw_cap utility routine in mt76x02-lib
module in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify frequency offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify temperature offset parsing with mt76x2 driver using
eeprom utility routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify rssi_offset parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify lna gain parsing with mt76x2 driver using eeprom utility
routines available in mt76x02-lib module
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_get_rx_gain and mt76x02_get_lna_gain utility routines
for rx gain parsing. mt76x02_get_rx_gain and mt76x02_get_lna_gain
will be reused for eeprom parsing in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0_set_country_reg routine for the moment
since it is partial and it is not actually used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_ext_pa_enabled utility routine in mt76x02_eeprom.c
and remove duplicated code. This is a preliminary patch to
unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_efuse_read and mt76x2_get_efuse_data in mt76x02_eeprom.c
in order to be reused in mt76x0 driver for eeprom parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_setaddr utility routine in mt76x02-lib
module and remove duplicated code. This is a preliminary patch
to unify eeprom code between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_eeprom_get utility routine in mt76x02_eeprom.h since
it will be used to parse mt76x0 eeprom in order to unify eeprom
support between mt76x2 and mt76x0 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move shared eeprom utility routines in mt76x02_eeprom.h and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2 and mt76x0 common definitions in mt76x02_eeprom.h
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add stbc tx power eeprom parsing support for mt76x2 driver.
When writing power entries, make a distinction between rates that are
read from the same EEPROM value, but have separate register entries.
No effect on runtime behavior, but preparation for unification with mt76x0
and for placing restrictions on individual rate power limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move seq_put_array utility routine in mt76-core module
in order to be reused in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7650 PCI id found on ASUS rt-51ac to pci_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix tx power configuration for VHT 1SS/STBC mcs 9 since
in MT_TX_PWR_CFG_{8,9} mcs 8,9 bits are GENMASK(21,16) and
GENMASK(29,24) while GENMASK(15,6) are marked as reserved
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The capability bit was added to the driver and had been negotiated
with the firmware, but then got forgotten in the firmware and later
reused for a different capability. Now the firmware added it in a
new bit.
Fixes: 2eabc84d2f ("iwlwifi: mvm: only send LEDS_CMD when the FW supports it")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As a temporary stage in the 22560 devices bring up, we disabled
power save, to avoid bugs related to that domain.
Now we would like to use power save so enable the balanced mode,
and allow configuring the mode via module parameter.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices we will have more than one debug buffer.
Prepare the infrastructure for allocation and release of
multiple debug buffers by grouping the variables in an array
of structures and moving it to trans section, where they will
be visible to opmode and FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to be able to build A-MSDUs in higher layers, e.g. by
xmit_more, so support transmitting SKBs with fraglist to use
it for such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer want to consider the RSSI if the beacon / probe
has been heard on an adjacent channel.
This was based on a firmware capability that is now
unavailable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating as a soft ap with wep security, the key was not
configured to the fw for the stations, based on the fact that the
key will be specified in the tx command.
However, in the new tx api the tx command does not include the key,
which resulted in all data frames going out un-encrypted.
Fix it by configuring the key for all the stations as they are added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RB size can be configured by user to be greater than 4K.
That's needed for monitor to capture big AMSDUs.
The firmware now enables different RB sizes configuration
via context info.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since AMSDUs are not de-aggregated by HW in monitor mode,
we still need the option for setting large RBs (up to 12K).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today, the length of a debug message in iwl_trans_pcie_reclaim
may pass the MAX_MSG_LEN, which is 110.
An example for this kind of message is:
'iwl_trans_pcie_reclaim: Read index for DMA queue txq id (2),
last_to_free 65535 is out of range [0-65536] 2 2.'
Cut the message a bit so it will fit the allowed MAX_MSG_LEN.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow us to reuse the function later for adding fraglist
SKBs to the TFD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When anything fails, we unmap the whole TFD in three different
places scattered throughout the code. Unify this to a single
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the skb fragment loop into a helper routine to be able
to reuse it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The non-shared antenna was wrong for 22000 device series.
Fix it to ANT_B for correct antenna preference by coex in MVM driver.
Fixes: e34d975e40 ("iwlwifi: Add a000 HW family support")
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.
When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.
We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.
To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.
Fixes: 04fd2c2822 ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Check the actual bit (mask) in Rx notification rate_n_flags.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no value in having an anonymous struct for holding
a few fields, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The SP length in the ADD_STA command is an actual number of
frames, and not the SP len as it appears in the WME IE.
Fix that comment. The actual code is fine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
.max_tfd_queue_size was ommited for 1000 card serries leading to oops in
swiotlb.
Fixes: 7b3e42ea2e ("iwlwifi: support multiple tfd queue max sizes for different devices")
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The allocation of hwsim radio identifiers uses a post-increment from 0,
so the first radio has idx 0. This idx is explicitly excluded from
multicast announcements ever since, but it is unclear why.
Drop that idx check and announce the first radio as well. This makes
userspace happy if it relies on these events.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The asynchronous destruction from a work-queue of radios tagged with
destroy-on-close may race with the owning namespace about to exit,
resulting in potential use-after-free of that namespace.
Instead of using a work-queue, move radios about to destroy to a
temporary list, which can be worked on synchronously after releasing
the lock. This should be safe to do from the netlink socket notifier,
as the namespace is guaranteed to not get released.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cleanup of radios during namespace exit has recently been reworked
to directly delete a radio while temporarily releasing the spinlock,
fixing a race condition between the work-queue execution and namespace
exits. However, the temporary unlock allows unsafe modifications on the
iterated list, resulting in a potential crash when continuing the
iteration of additional radios.
Move radios about to destroy to a temporary list, and clean that up
after releasing the spinlock once iteration is complete.
Fixes: 8cfd36a0b5 ("mac80211_hwsim: fix use-after-free bug in hwsim_exit_net")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey':
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 66cffd6daa ("b43: fix transmit failure when VT is switched"),
a condition is noted where the network controller needs to be reset. Note
that this situation happens when running the open-source firmware
(http://netweb.ing.unibs.it/~openfwwf/), plus a number of other special
conditions.
for a different card model, it is reported that this change breaks
operation running the proprietary firmware
(https://marc.info/?l=linux-wireless&m=153504546924558&w=2). Rather
than reverting the previous patch, the code is tweaked to avoid the
reset unless the open-source firmware is being used.
Fixes: 66cffd6daa ("b43: fix transmit failure when VT is switched")
Cc: Stable <stable@vger.kernel.org> # 4.18+
Cc: Taketo Kabe <kabe@sra-tohoku.co.jp>
Reported-and-tested-by: D. Prabhu <d.praabhu@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mt76_fw dependency from mt76x0u_upload_firmware routine since
it does not define firmware layout properly. Moreover use mt76_poll_msec
utility routine to check if the fw is properly running
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused usb header file and move mt76x0 firmware definition
in usb.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mcu.c source file since it contains just 'one-line' function
that is shared between PCI and USB code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Firmware loading is usb specific, move it to usb.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragments.
This can happen if the driver grabs one or two fragments for rx ring
refill, while other drivers use (and free up) the remaining fragments.
The 32 KiB higher-order page can only be freed once all users have freed
their fragments.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_phy_tssi_compensate routine in mt76x2-common module
since it is shared between mt76x2 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu_calibrate routine in mt76x02-lib module since it is
shared between USB and PCI code. Moreover remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi