Tegra186 has a total of nine I2C controllers that are compatible with
the I2C controllers introduced in Tegra114. Two of these controllers
share pads with two DPAUX controllers (for AUX transactions).
Signed-off-by: Thierry Reding <treding@nvidia.com>
The initial patch only added UARTA, but there's no reason we shouldn't
be adding all of them. While at it, also specify the missing clocks and
resets for UARTA.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has six CPUs: two CPUs are second generation Denver CPUs that
support ARMv8 and four CPUs are Cortex-A57 CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the initial support of Tegra186 SoC. It provides enough to
enable the serial console and boot from an initial ramdisk.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[treding@nvidia.com: remove leading 0 from unit-addresses]
[treding@nvidia.com: remove unused nvidia,bpmp property]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This changes SDHI0 pin names for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI2 for H3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI2 for M3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SDHI0 on M3ULCB board SD card slot
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports watchdog timer for M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO keys on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO leds on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7796 SoC based M3ULCB low cost
board (R-Car Starter Kit Pro)
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This updates H3ULCB device tree header with official board name
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device trees,
with some tweaks to OMAP mach files to deal with CPU feature print
misformatting, potential NULL ptr dereference and one setup issue
with UARTs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jSKg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Again a set of smaller fixes across several platforms (OMAP, Marvell,
Allwinner, i.MX, etc).
A handful of typo fixes and smaller missing contents from device
trees, with some tweaks to OMAP mach files to deal with CPU feature
print misformatting, potential NULL ptr dereference and one setup
issue with UARTs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
arm64: dts: marvell: add unique identifiers for Armada A8k SPI controllers
arm64: dts: marvell: fix clocksource for CP110 slave SPI0
arm64: dts: marvell: Fix typo in label name on Armada 37xx
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
ARM: dts: imx53-qsb: Fix regulator constraints
ARM: dts: sun8i: fix the pinmux for UART1
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j/xt
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Topic branch with DT arm64 changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for interrupt properties in exynos7
arm64: dts: exynos: Fix invalid GIC interrupt flags in exynos7
Signed-off-by: Olof Johansson <olof@lixom.net>
Adding the new "community" board for Armada 3700
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlguJU8jHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9VNGQCfRB3BbnBCIgpu0n9wWumR7LsDmJYAoIafat62MwuH
gRsYSdrm1VVhMHwQ
=LnOL
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.10-1' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.10 (part 1)
Adding the new "community" board for Armada 3700
* tag 'mvebu-dt64-4.10-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: Add definition for the Globalscale Marvell ESPRESSOBin Board
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for the Allwinner A64, their first armv8 SoC.
-----BEGIN PGP SIGNATURE-----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=JkJ+
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt64
Allwinner arm64 DT changes for 4.10
Support for the Allwinner A64, their first armv8 SoC.
* tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: dts: add Pine64 support
Documentation: devicetree: add vendor prefix for Pine64
arm64: dts: add Allwinner A64 SoC .dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
- Correct the hardware pin number of the usb node on the Hip06
- Add the Hisilicon Hip07 D05 board dts binding
- Add the initial dts for the Hip07 D05 board
- Fix the warning for the node without reg propery on the Hip06
- Fix the sas am max transmissions quirk property on the Hip06
- Disable the sas0 and sas2 on D03 board
- Add refclk node for SAS on the Hip06
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MVHS
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-4.10' of git://github.com/hisilicon/linux-hisi into next/dt64
ARM64: DT: Hisilicon SoC DT updates for 4.10
- Correct the hardware pin number of the usb node on the Hip06
- Add the Hisilicon Hip07 D05 board dts binding
- Add the initial dts for the Hip07 D05 board
- Fix the warning for the node without reg propery on the Hip06
- Fix the sas am max transmissions quirk property on the Hip06
- Disable the sas0 and sas2 on D03 board
- Add refclk node for SAS on the Hip06
* tag 'hisi-arm64-dt-4.10' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisi: add refclk node to hip06 dts files for SAS
arm64: dts: hisi: disable sas0 and sas2 for d03
arm64: dts: hisi: fix hip06 sas am-max-trans quirk
arm64: dts: hip06: Fix no reg property warning
arm64: dts: hisilicon: Add initial dts for Hip07 D05 board
Documentation: arm64: Add Hisilicon Hip07 D05 dts binding
arm64: dts: hip06: Correct hardware pin number of usb node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKrk2AAoJEFBXWFqHsHzOQlwH+wQXK2WABTOjRVchLOzup/cD
UtB7mbmXJrBSePa3OTvF8xMk4VFfjm9oljmLnUEnzWEfjsS2aURT2GJBWv/ddhqw
Mg/fYcZ1LgzJq8VOnenLpF1L2jc/I2hivCkBNmmkMK0HQvURKEAsdqNDc7Zg0meY
64qokll9Uz4DM2yeHkrUs9Q13UPs9/88ikYbE+CVDFaI0TCJjZUTImmjYkt8pJyk
poDtW6yE8ibMNk2DK4e4tthPRcYnhkFOtSJF6Qy6jouV/J9+aaKG5+rj4MBeF8Aj
T2+RFSQ4s2BuI5cH3qQq8Fv7lvF0Ay4wNWZl420R7shjbPWQNdIcbAbKL+51De0=
=jiir
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Freescale arm64 device tree updates for 4.10:
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
* tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add TMU device tree support for LS2080A
arm64: dts: ls1043a: Add TMU device tree support for LS1043A
arm64: dts: add LS1046A-QDS board support
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-RDB board support
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
arm64: dts: add QorIQ LS1046A SoC support
dt-bindings: ahci-fsl-qoriq: updated for SoC ls1046a
dt-bindings: qoriq-clock: add LS1043A/LS1046A/LS2080A compatible for clockgen
dt-bindings: i2c: adds two more nxp devices
dt-bindings: fsl: add LS1043A/LS1046A/LS2080A compatible for SCFG and DCFG
dt-bindings: fsl: Add LS1043A/LS1046A/LS2080A SoC compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
-----BEGIN PGP SIGNATURE-----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=qXyV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add #pinctrl-cells for pinctrl-single using dts files. This allows
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
* tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add #pinctrl-cells for pinctrl-single instances
Signed-off-by: Olof Johansson <olof@lixom.net>
Since, arm64 can support all offset within a double word limit. Therefore,
now support other lengths within that range as well.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Arm64 hardware does not always report a watchpoint hit address that
matches one of the watchpoints set. It can also report an address
"near" the watchpoint if a single instruction access both watched and
unwatched addresses. There is no straight-forward way, short of
disassembling the offending instruction, to map that address back to
the watchpoint.
Previously, when the hardware reported a watchpoint hit on an address
that did not match our watchpoint (this happens in case of instructions
which access large chunks of memory such as "stp") the process would
enter a loop where we would be continually resuming it (because we did
not recognise that watchpoint hit) and it would keep hitting the
watchpoint again and again. The tracing process would never get
notified of the watchpoint hit.
This commit fixes the problem by looking at the watchpoints near the
address reported by the hardware. If the address does not exactly match
one of the watchpoints we have set, it attributes the hit to the
nearest watchpoint we have. This heuristic is a bit dodgy, but I don't
think we can do much more, given the hardware limitations.
Signed-off-by: Pavel Labath <labath@google.com>
[panand: reworked to rebase on his patches]
Signed-off-by: Pratyush Anand <panand@redhat.com>
[will: use __ffs instead of ffs - 1]
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 hardware supports watchpoint at any double word aligned address.
However, it can select any consecutive bytes from offset 0 to 7 from that
base address. For example, if base address is programmed as 0x420030 and
byte select is 0x1C, then access of 0x420032,0x420033 and 0x420034 will
generate a watchpoint exception.
Currently, we do not have such modularity. We can only program byte,
halfword, word and double word access exception from any base address.
This patch adds support to overcome above limitations.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
This patch adds device nodes for MFC video codec device to Exynos5433 SoC
dtsi and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for JPEG codec device to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for GScaler devices to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UART3 device is not really needed for enabling audio block on TM2.
Enabling it made it working by enabling some common parent clocks,
what is now handled by improved exynos5433 clocks driver. Thus the UART3
device node can be safely disabled. The assigned-clocks entries are
however still needed, so move them under the respective CMU node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Without this patch the clkout clock is orphaned and sound doesn't
work properly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move initial FSYS CMU (related to USB 3.0 devices) clocks configuration
from generic exynos5433.dtsi file to exynos5433-tm2.dts, as this is
a board specific item.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Audio PLL and oscillator clocks are proper parent clocks for AUD CMU.
They are not visible as such on first glance on Exynos5433 SoC docs,
but they are needed for this CMU to operate properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch corrects FSYS CMU parent clocks specified in clock controller
node to let improved Exynos5433 clocks driver to control proper clocks
on FSYS<->TOP CMU boundary.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts. The
GIC requires shared interrupts to be edge rising or level high. Platform
declares support for both. Set all interrupts type to level high, as this
works fine - tested on Exynos5433-based TM2 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
KVM calls kvm_pmu_set_counter_event_type() when PMCCFILTR is configured.
But this function can't deals with PMCCFILTR correctly because the evtCount
bits of PMCCFILTR, which is reserved 0, conflits with the SW_INCR event
type of other PMXEVTYPER<n> registers. To fix it, when eventsel == 0, this
function shouldn't return immediately; instead it needs to check further
if select_idx is ARMV8_PMU_CYCLE_IDX.
Another issue is that KVM shouldn't copy the eventsel bits of PMCCFILTER
blindly to attr.config. Instead it ought to convert the request to the
"cpu cycle" event type (i.e. 0x11).
To support this patch and to prevent duplicated definitions, a limited
set of ARMv8 perf event types were relocated from perf_event.c to
asm/perf_event.h.
Cc: stable@vger.kernel.org # 4.6+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're missing the handling code for the cycle counter accessed
from a 32bit guest, leading to unexpected results.
Cc: stable@vger.kernel.org # 4.6+
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wFjD
-----END PGP SIGNATURE-----
Merge tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
- Add bindings for mtk-scpsys for mt2701
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
* tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt2701: Use real clock for UARTs
arm: dts: mt2701: Add clock controller device nodes
arm64: dts: mt8173: Fix auxadc node
soc: mediatek: Add MT2701 power dt-bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzRqEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYE8HAgA
hFPUM6OmYsP81xJ8B8NscxZXi0r5ZTp14ouF5cREPF5mwXghrE5ZEGC/+xQJ/X4p
WSSGglNEJV5Ofs869wYDU3yZwNRzwkK7bGY+Mzq8eySYzkfZR2VZUf5ZStsLfUS1
j6Gr7jr2gwFtpjlwLmaUj8O4i/I3FfTiDLobqdpXoeoRcisLXS4/xDxEC1143TDR
ctylpGFEW/LXC1L4kTyLUZ6688654IC5qZBp4yHLIgb+qfd8k+CEjEyxtCzGpAQJ
sLQnsjjer4C3MqgOSDAjyguKpePCz0VIoE8wct136sQh20isbgWuhQjQ9+QzAaE+
/N+j0d87kaHUdPa097wQkg==
=LC5U
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
64bit devicetree changes including the px5 evaluation board
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
* tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
arm64: dts: rockchip: add cpu-id nvmem cell node for rk3399
arm64: dts: rockchip: add sdmmc support for px5-evb
arm64: dts: rockchip: Add more properties for emmc on px5-evb
arm64: dts: rockchip: Add PX5 Evaluation board
arm64: dts: rockchip: add powerdomain for typec on rk3399
arm64: dts: rockchip: fix i2c resource error of rk3368
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zbqq
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Finally, I am really pleased to announce adding support for Exynos5433 ARMv8
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
* tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add dts file for Exynos5433-based TM2E board
arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board
arm64: dts: exynos: Add dtsi files for Samsung Exynos5433 64bit SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
- Switch CPU enable-method from spin-table to PSCI
- Add OPP tables to support generic cpufreq driver
- Misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=K2GC
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt64-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt64
UniPhier ARM64 SoC DT updates for v4.10
- Switch CPU enable-method from spin-table to PSCI
- Add OPP tables to support generic cpufreq driver
- Misc fixes
* tag 'uniphier-dt64-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: make compatible of syscon nodes SoC-specific
arm64: dts: uniphier: add CPU clocks and OPP tables for LD20 SoC
arm64: dts: uniphier: add CPU clock and OPP table for LD11 SoC
arm64: dts: uniphier: increase register region size of sysctrl node
arm64: dts: uniphier: switch over to PSCI enable method
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt64
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
All of them are fixes for arm64 device tree
- 2 for the SPI node on the Armada 7K/8K
- 1 for the clock node on the Armada 37xx
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlgk6sUjHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9VwEgCdGuixX9TYgWna2/PdhtVs5JXdW98Amwb054ygu7dw
2ONd6XGynL1PpVhQ
=qm28
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.9-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.9 (part 1)
All of them are fixes for arm64 device tree
- 2 for the SPI node on the Armada 7K/8K
- 1 for the clock node on the Armada 37xx
* tag 'mvebu-fixes-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add unique identifiers for Armada A8k SPI controllers
arm64: dts: marvell: fix clocksource for CP110 slave SPI0
arm64: dts: marvell: Fix typo in label name on Armada 37xx
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable additional options necessary to boot rk3399-based boards to
boot from either emmc or usb devices, like the arasan sdhci and its phy
as well as the usb2 phy and general rockchip power-domain support.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Many rockchip based arm64 boards use RK808 as PMIC, so
enabe it here let the board bootup normally.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[added rk808-rtc as module and rk808-clk output built in]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C and MMC are very basic modules for a board to bootup, as I2C always
used to configure PMIC and MMC devices often used to store filesytem.
So enable them here to let the rockchip based arm64 boards can bootup.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
No need to duplicate the same define everywhere. Since
the only user is stop-machine and the only provider is
s390, we can use a default implementation of cpu_relax_yield()
in sched.h.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvm@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-s390 <linux-s390@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1479298985-191589-1-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are incorrectly defining the pwr LED, attaching it to a gpio line
that is wired to the Wi-Fi SDIO module (which fails due to this).
The actual power LED is connected to the GPIO expander, which we don't
expose currently.
Fixes: 9d56c22a78 ("ARM: bcm2835: Add devicetree for the Raspberry Pi 3.")
Thanks-to: Eric Anholt <eric@anholt.net> [for clarifying we can't control the LED]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the USB PHY driver was introduced the reset framework did not
have support for triggering a reset pulse for shared resets. On GXBB
however there is only one reset line for both PHYs (meaning we have a
shared reset line). With the latest changes to the reset framework and
the corresponding updates to the phy-meson8b-usb2 driver we can now pass
the reset to the second PHY as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The arm64 kernel assumes that FP/ASIMD units are always present
and accesses the FP/ASIMD specific registers unconditionally. This
could cause problems when they are absent. This patch adds the
support for kernel handling systems without FP/ASIMD by skipping the
register access within the kernel. For kvm, we trap the accesses
to FP/ASIMD and inject an undefined instruction exception to the VM.
The callers of the exported kernel_neon_begin_partial() should
make sure that the FP/ASIMD is supported.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: add comment on the ARM64_HAS_NO_FPSIMD conflict and the new location]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The hypervisor may not have full access to the kernel data structures
and hence cannot safely use cpus_have_cap() helper for checking the
system capability. Add a safe helper for hypervisors to check a constant
system capability, which *doesn't* fall back to checking the bitmap
maintained by the kernel. With this, make the cpus_have_cap() only
check the bitmask and force constant cap checks to use the new API
for quicker checks.
Cc: Robert Ritcher <rritcher@cavium.com>
Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As there are no users left, we can remove cpu_relax_lowlatency()
implementations from every architecture.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Cc: <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1477386195-32736-6-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For spinning loops people do often use barrier() or cpu_relax().
For most architectures cpu_relax and barrier are the same, but on
some architectures cpu_relax can add some latency.
For example on power,sparc64 and arc, cpu_relax can shift the CPU
towards other hardware threads in an SMT environment.
On s390 cpu_relax does even more, it uses an hypercall to the
hypervisor to give up the timeslice.
In contrast to the SMT yielding this can result in larger latencies.
In some places this latency is unwanted, so another variant
"cpu_relax_lowlatency" was introduced. Before this is used in more
and more places, lets revert the logic and provide a cpu_relax_yield
that can be called in places where yielding is more important than
latency. By default this is the same as cpu_relax on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-2-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All boards from the Tronsmart Vega S95 series are sharing similar MMC
based hardware.
sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported
by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is
generated by PWM_E.
sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO
regulator, meaning it only supports 3.3V (which seems to be hard-wired).
The eMMC chip is connected to sd_emmc_c and is implemented similar to
the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators
are used).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable Ethernet on the p23x board, pinctrl attribute is only added for
the p230 board since the p231 only uses the Internal PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add Ethernet node with Internal PHY selection for the Amlogic GXL SoCs
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
meson-gx.dtsi was directly derived from meson-gxbb.dtsi, so keep the
copyrights in chronological order to not give a wrong impression.
Fixes: c328666d58 ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infraread Receiver on the p23x board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add SD/SDIO/MMC nodes and PWM 32768Hz clock configuration to provide
storage and WiFi functionality on the p23x boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add clock node for Amlogic Meson GXL.
The GXBB compatible is retained since the GXBB clock tree is used for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl nodes and pin definitions for Amlogic Meson GXL.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: use GXBB include until GXL pinctrl support merged]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds ARM Performance Monitor Unit dt node for exynos7.
PMU provides various statistics on the operation of the CPU and
memory system at runtime, which are very useful when debugging or
profiling code. This enables the same.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed with "Add level for cpu dt node for exynos7"]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add otg-port nodes for both u2phy0 and u2phy1. The otg-port can
be used for USB2.0 part of USB3.0 OTG controller.
Signed-off-by: William Wu <wulf@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We will only maintain 1 dts for D03 and there are 50MHz
and 66MHz versions of D03: so we expect UEFI to update
refclk rate in the fdt at boot time.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The SAS nodes sas0 and sas2 are not available on d03, so
disable them.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The string for the am max transmissions quirk property
is not correct -> fix it.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Warning (unit_address_vs_reg): Node /soc/ethernet@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/ethernet@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/ethernet@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/ethernet@1 has a unit name, but no reg property
Fix warning when build with W=1.
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Adding initial dt file for Hip07 D05 board, it is with dual socket
and each socket has two SCCLs(supper cpu cluster), one SCCL contains
four clusters and each cluster has quard Cortex-A72.
Since each SCCL has their own DDR controller, it could be treated as
a separate numa node. Thus, there are four numa nodes(one node with
sixteen core) on Hip07 SoC.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
With no coherency to worry about, just plug'em straight in.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add the sd power-domain, its qos area and assign it to the
sdmmc device node.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Control power domain for eMMC via genpd to reduce power consumption.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add backlight node for evb board, perpare for panel device node.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fixes that sometimes hang at start-up time of the system.
As the below log:
...
[ 11.136543] calling pm_genpd_debug_init+0x0/0x60 @ 1
[ 11.141602] initcall pm_genpd_debug_init+0x0/0x60 returned 0 after 11 usecs
[ 11.148558] calling genpd_poweroff_unused+0x0/0x84 @ 1
<hang>
In some cases, the rk3399 should turn off the gmac power domain to save
power if some boards didn't register the gmac device node for rk3399.
Then, rk3399 need to make sure the gmac's pclk enabled if we need
operate the gmac power domain. (Due to the NOC had enabled always)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
wait for next week.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYJvAXFBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
ztUH/3DZVYkVYUea+Sk1mBnLaK5cbEJMGtxV/NsAqwz8rYB981cB5Iqw0+f2HX2G
LWLc0cf/kyUH+6TrFxQFyXLsBvV7xku2YwJdoiRutpR50767qPFPaPUBHcxCYPYR
MI4VSXb1hW0c4rd8409HesKv5qc5BiYjdWKPMu+f1LUF2CED+Xq4SWHVg+CwSE8i
UInvFUlj/ejQlSdxN2piv87SRcMuO+4nzP+JbtyN7onvtLIah6JfvHhlOO6em+0c
KX1G3qQ6fth6jewTdOPUB1Tx8CoEAZ+YLieRQA19vGHVI4eIhofDgtSaPZJmu9G7
0kjbrlqAuViTEsRl7Dx8zT8OpBM=
=N6w9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM fixes. There are a couple pending x86 patches but they'll have to
wait for next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Kick VCPUs when queueing already pending IRQs
KVM: arm/arm64: vgic: Prevent access to invalid SPIs
arm/arm64: KVM: Perform local TLB invalidation when multiplexing vcpus on a single CPU
We already have a macro to invoke boot services which on x86 adapts
automatically to the bitness of the EFI firmware: efi_call_early().
The macro allows sharing of functions across arches and bitness variants
as long as those functions only call boot services. However in practice
functions in the EFI stub contain a mix of boot services calls and
protocol calls.
Add an efi_call_proto() macro for bitness-agnostic protocol calls to
allow sharing more code across arches as well as deduplicating 32 bit
and 64 bit code paths.
On x86, implement it using a new efi_table_attr() macro for bitness-
agnostic table lookups. Refactor efi_call_early() to make use of the
same macro. (The resulting object code remains identical.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-8-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While debugging a kernel image size issue, I discovered that if all
non ARCH_QCOM configs in the ARM64 defconfig are disabled, the QCOM
pinctrl drivers will not be built.
The QCOM pinctrl drivers have a dependency on GPIOLIB which was being
selected when other ARCH configs were enabled, but ARCH_QCOM doesn't
select GPIOLIB directly. Let's select GPIOLIB here to ensure the pinctrl
drivers are built for QCOM platforms.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial device tree support for Qualcomm MSM8994 SoC and
Huawei Angler / Google Nexus 6P support.
The device tree is based on the Google 3.10 kernel tree.
The device can be booted into the initrd with only one CPU running.
Signed-off-by: Bastian Köcher <mail@kchr.de>
[jeremymc@redhat.com: removed Kconfig, defconfig, move from Huawei to qcom dir]
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Tested-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial device tree support for Qualcomm MSM8992 SoC and
LG Bullhead / Google Nexus 5X support.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add support to Analog audio both Playback and Capture via
msm8916 WCD muti codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Given the mimimal hardware support for msm899(2/4) currently.
A few config options are needed to allow for continued
development and booting.
The following are needed for continued development and
booting:
-8994 pinctrl for serial support
-Enable Global Glock Controller (gcc)
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5c2j
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
This patch moves arm64's struct thread_info from the task stack into
task_struct. This protects thread_info from corruption in the case of
stack overflows, and makes its address harder to determine if stack
addresses are leaked, making a number of attacks more difficult. Precise
detection and handling of overflow is left for subsequent patches.
Largely, this involves changing code to store the task_struct in sp_el0,
and acquire the thread_info from the task struct. Core code now
implements current_thread_info(), and as noted in <linux/sched.h> this
relies on offsetof(task_struct, thread_info) == 0, enforced by core
code.
This change means that the 'tsk' register used in entry.S now points to
a task_struct, rather than a thread_info as it used to. To make this
clear, the TI_* field offsets are renamed to TSK_TI_*, with asm-offsets
appropriately updated to account for the structural change.
Userspace clobbers sp_el0, and we can no longer restore this from the
stack. Instead, the current task is cached in a per-cpu variable that we
can safely access from early assembly as interrupts are disabled (and we
are thus not preemptible).
Both secondary entry and idle are updated to stash the sp and task
pointer separately.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Shortly we will want to load a percpu variable in the return from
userspace path. We can save an instruction by folding the addition of
the percpu offset into the load instruction, and this patch adds a new
helper to do so.
At the same time, we clean up this_cpu_ptr for consistency. As with
{adr,ldr,str}_l, we change the template to take the destination register
first, and name this dst. Secondly, we rename the macro to adr_this_cpu,
following the scheme of adr_l, and matching the newly added
ldr_this_cpu.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In the absence of CONFIG_THREAD_INFO_IN_TASK, core code maintains
thread_info::cpu, and low-level architecture code can access this to
build raw_smp_processor_id(). With CONFIG_THREAD_INFO_IN_TASK, core code
maintains task_struct::cpu, which for reasons of hte header soup is not
accessible to low-level arch code.
Instead, we can maintain a percpu variable containing the cpu number.
For both the old and new implementation of raw_smp_processor_id(), we
read a syreg into a GPR, add an offset, and load the result. As the
offset is now larger, it may not be folded into the load, but otherwise
the assembly shouldn't change much.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Subsequent patches will make smp_processor_id() use a percpu variable.
This will make smp_processor_id() dependent on the percpu offset, and
thus we cannot use smp_processor_id() to figure out what to initialise
the offset to.
Prepare for this by initialising the percpu offset based on
current::cpu, which will work regardless of how smp_processor_id() is
implemented. Also, make this relationship obvious by placing this code
together at the start of secondary_start_kernel().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When returning from idle, we rely on the fact that thread_info lives at
the end of the kernel stack, and restore this by masking the saved stack
pointer. Subsequent patches will sever the relationship between the
stack and thread_info, and to cater for this we must save/restore sp_el0
explicitly, storing it in cpu_suspend_ctx.
As cpu_suspend_ctx must be doubleword aligned, this leaves us with an
extra slot in cpu_suspend_ctx. We can use this to save/restore tpidr_el1
in the same way, which simplifies the code, avoiding pointer chasing on
the restore path (as we no longer need to load thread_info::cpu followed
by the relevant slot in __per_cpu_offset based on this).
This patch stashes both registers in cpu_suspend_ctx.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_THREAD_INFO_IN_TASK is selected, task stacks may be freed
before a task is destroyed. To account for this, the stacks are
refcounted, and when manipulating the stack of another task, it is
necessary to get/put the stack to ensure it isn't freed and/or re-used
while we do so.
This patch reworks the arm64 stack walking code to account for this.
When CONFIG_THREAD_INFO_IN_TASK is not selected these perform no
refcounting, and this should only be a structural change that does not
affect behaviour.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The walk_stackframe functions is architecture-specific, with a varying
prototype, and common code should not use it directly. None of its
current users can be built as modules. With THREAD_INFO_IN_TASK, users
will also need to hold a stack reference before calling it.
There's no reason for it to be exported, and it's very easy to misuse,
so unexport it for now.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In arm64's die and __die routines we pass around a thread_info, and
subsequently use this to determine the relevant task_struct, and the end
of the thread's stack. Subsequent patches will decouple thread_info from
the stack, and this approach will no longer work.
To figure out the end of the stack, we can use the new generic
end_of_stack() helper. As we only call __die() from die(), and die()
always deals with the current task, we can remove the parameter and have
both acquire current directly, which also makes it clear that __die
can't be called for arbitrary tasks.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We define current_stack_pointer in <asm/thread_info.h>, though other
files and header relying upon it do not have this necessary include, and
are thus fragile to changes in the header soup.
Subsequent patches will affect the header soup such that directly
including <asm/thread_info.h> may result in a circular header include in
some of these cases, so we can't simply include <asm/thread_info.h>.
Instead, factor current_thread_info into its own header, and have all
existing users include this explicitly.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Subsequent patches will move the thread_info::{task,cpu} fields, and the
current TI_{TASK,CPU} offset definitions are not used anywhere.
This patch removes the redundant definitions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We have a comment claiming __switch_to() cares about where cpu_context
is located relative to cpu_domain in thread_info. However arm64 has
never had a thread_info::cpu_domain field, and neither __switch_to nor
cpu_switch_to care where the cpu_context field is relative to others.
Additionally, the init_thread_info alias is never used anywhere in the
kernel, and will shortly become problematic when thread_info is moved
into task_struct.
This patch removes both.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the node for the thermal sensor of the bcm2837-soc
to the device tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the thermal driver for bcm2837 to list of compiled modules
in the default config.
Changelog:
V7 -> V8: rebased
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
- Kick the vcpu when a pending interrupt becomes pending again
- Prevent access to invalid interrupt registers
- Invalid TLBs when two vcpus from the same VM share a CPU
-----BEGIN PGP SIGNATURE-----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=vj/s
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for v4.9-rc4
- Kick the vcpu when a pending interrupt becomes pending again
- Prevent access to invalid interrupt registers
- Invalid TLBs when two vcpus from the same VM share a CPU
pm8994 has 22 gpios, so add the missing interrupts entry for one
of the gpios
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On the APQ8016 SBC, the LDO2 PM8916 regulator feeds 1.2V to the following:
- VDDA_1P2_MIPI_DSI and VDDA_MIPI_CSI pins on APQ8016.
- VCCCAD pins on the LPDDR3 chip.
- VDDPX_1 pins on APQ8016.
The LDO6 regulator feeds 1.8V to:
- VDAA_MIPI_DSI0_PLL pin on APQ8016.
- QFPROM_BLOW_VDD pin on PM8916.
- The AVDD, A2VDD and DVDD pins on ADV7533 bridge.
The LDO17 regulator feeds 3.3V to:
- The V3P3 pin on ADV7533 bridge.
Currently, the regulator min/max voltages for all the LDOs are set to the
range of what the PMIC supports. Set the ranges for L2, L6 and L17 to what
we need, i.e. 1.2V, 1.8V and 3.3V respectively.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
pm_rst, aclk_rst and pclk_rst should be controlled by driver, so we
need to add these three resets for PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
For several reasons it is preferable to use {READ,WRITE}_ONCE() rather than
ACCESS_ONCE(). For example, these handle aggregate types, result in shorter
source code, and better document the intended access (which may be useful for
instrumentation features such as the upcoming KTSAN).
Over a number of patches, most uses of ACCESS_ONCE() in arch/arm64 have been
migrated to {READ,WRITE}_ONCE(). For consistency, and the above reasons, this
patch migrates the final remaining uses.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The libhugetlbfs meets several failures since the following functions
do not use the correct address:
huge_ptep_get_and_clear()
huge_ptep_set_access_flags()
huge_ptep_set_wrprotect()
huge_ptep_clear_flush()
This patch fixes the wrong address for them.
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The find_num_contig() will return 1 when the pmd is not present.
It will cause a kernel dead loop in the following scenaro:
1.) pmd entry is not present.
2.) the page fault occurs:
... hugetlb_fault() --> hugetlb_no_page() --> set_huge_pte_at()
3.) set_huge_pte_at() will only set the first PMD entry, since the
find_num_contig just return 1 in this case. So the PMD entries
are all empty except the first one.
4.) when kernel accesses the address mapped by the second PMD entry,
a new page fault occurs:
... hugetlb_fault() --> huge_ptep_set_access_flags()
The second PMD entry is still empty now.
5.) When the kernel returns, the access will cause a page fault again.
The kernel will run like the "4)" above.
We will see a dead loop since here.
The dead loop is caught in the 32M hugetlb page (2M PMD + Contiguous bit).
This patch removes wrong pmd check, and fixes this dead loop.
This patch also removes the redundant checks for PGD/PUD in
the find_num_contig().
Acked-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The default hugepage size when 64K pages are enabled is set to 2MB using
the contiguous PTE bit. The add_default_hugepagesz(), however, uses
CONT_PMD_SHIFT instead of CONT_PTE_SHIFT. There is no functional change
since the values are the same.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In drivers/mmc/core/host.c, there is "max-freqeuncy" property.
It should be same behavior, So Use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enabling SPI controllers, which are attached to different busses
inside an SoC, may result in overlapping enumeration and cause
sysfs registration failure. Example log after enabling two
controllers on Armada 8040 SoC with same identifiers:
[ 3.740415] sysfs: cannot create duplicate filename
'/class/spi_master/spi0'
[ 3.747510] ------------[ cut here ]------------
[ 3.752145] WARNING: at fs/sysfs/dir.c:31
[...]
[ 4.002299] orion_spi: probe of f4700600.spi failed with error -17
spi-orion driver offers dedicated DT property ('cell-index'), that
allow setting unique identifiers. Recently added support for CP110-slave
HW block introduced two new SPI controllers' nodes with same ID as
ones from CP110-master.
This commit fixes the issue by assigning different 'cell-index' values
for CP110-slave SPI controllers.
Fixes: 4eef78a009 ("arm64: dts: marvell: add description for the slave
CP110 in Armada 8K")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
I2C and SPI interfaces share common clock trees within the CP110 HW block.
It occurred that SPI0 interface has wrong clock assignment in the device
tree, which is fixed in this commit to a proper value.
Fixes: c749b8d9de32 ("arm64: dts: marvell: add description for the ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The label names of the peripheral clocks have a typo. Fix it before it is
more widely used.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
* Enable R-Car DU and related drivers as modules in defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ztt2
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/arm64
Renesas ARM64 Based SoC Defconfig Updates for v4.10
* Enable R-Car DU and related drivers as modules in defconfig
* tag 'renesas-arm64-defconfig-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: Enable DRM DU and V4L2 FCP + VSP modules
Signed-off-by: Olof Johansson <olof@lixom.net>
When CONFIG_KPROBE is disabled but CONFIG_UPROBE_EVENT is enabled, we get
following compilation error:
In file included from
.../arch/arm64/kernel/probes/decode-insn.c:20:0:
.../arch/arm64/include/asm/kprobes.h:52:5: error:
conflicting types for 'kprobe_fault_handler'
int kprobe_fault_handler(struct pt_regs *regs, unsigned int fsr);
^~~~~~~~~~~~~~~~~~~~
In file included from
.../arch/arm64/kernel/probes/decode-insn.c:17:0:
.../include/linux/kprobes.h:398:90: note:
previous definition of 'kprobe_fault_handler' was here
static inline int kprobe_fault_handler(struct pt_regs *regs, int trapnr)
^
.../scripts/Makefile.build:290: recipe for target
'arch/arm64/kernel/probes/decode-insn.o' failed
<asm/kprobes.h> is already included from <linux/kprobes.h> under #ifdef
CONFIG_KPROBE. So, this patch fixes the error by removing it from
decode-insn.c.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds support for uprobe on ARM64 architecture.
Unit tests for following have been done so far and they have been found
working
1. Step-able instructions, like sub, ldr, add etc.
2. Simulation-able like ret, cbnz, cbz etc.
3. uretprobe
4. Reject-able instructions like sev, wfe etc.
5. trapped and abort xol path
6. probe at unaligned user address.
7. longjump test cases
Currently it does not support aarch32 instruction probing.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We need to decide in some cases like uprobe instruction analysis that
whether the current mm context belongs to a 32 bit task or 64 bit.
This patch has introduced an unsigned flag variable in mm_context_t.
Currently, we set and clear TIF_32BIT depending on the condition that
whether an elf binary load sets personality for 32 bit or 64 bit
respectively.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
uprobe is registered at break_hook with a unique ESR code. So, when a
TRAP_BRKPT occurs, call_break_hook checks if it was for uprobe. If not,
then send a SIGTRAP to user.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
uprobe registers a handler at step_hook. So, single_step_handler now
checks for user mode as well if there is a valid hook.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64 step exception does not have any syndrome information. So, it is
responsibility of exception handler to take care that they handle it
only if exception was raised for them.
Since kgdb_step_brk_fn() always returns 0, therefore we might have problem
when we will have other step handler registered as well.
This patch fixes kgdb_step_brk_fn() to return error in case of step handler
was not meant for kgdb.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
decode-insn code has to be reused by arm64 uprobe implementation as well.
Therefore, this patch protects some portion of kprobe code and renames few
other, so that decode-insn functionality can be reused by uprobe even when
CONFIG_KPROBES is not defined.
kprobe_opcode_t and struct arch_specific_insn are also defined by
linux/kprobes.h, when CONFIG_KPROBES is not defined. So, protect these
definitions in asm/probes.h.
linux/kprobes.h already includes asm/kprobes.h. Therefore, remove inclusion
of asm/kprobes.h from decode-insn.c.
There are some definitions like kprobe_insn and kprobes_handler_t etc can
be re-used by uprobe. So, it would be better to remove 'k' from their
names.
struct arch_specific_insn is specific to kprobe. Therefore, introduce a new
struct arch_probe_insn which will be common for both kprobe and uprobe, so
that decode-insn code can be shared. Modify kprobe code accordingly.
Function arm_probe_decode_insn() will be needed by uprobe as well. So make
it global.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Page mappings with full RWX permissions are a security risk. x86
has an option to walk the page tables and dump any bad pages.
(See e1a58320a3 ("x86/mm: Warn on W^X mappings")). Add a similar
implementation for arm64.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[catalin.marinas@arm.com: folded fix for KASan out of bounds from Mark Rutland]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
max_addr was added as part of struct ptdump_info but has never actually
been used. Remove it.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The page table dumping code always assumes it will be dumping to a
seq_file to userspace. Future code will be taking advantage of
the page table dumping code but will not need the seq_file. Make
the seq_file optional for these cases.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ptdump_register currently initializes a set of page table information and
registers debugfs. There are uses for the ptdump option without wanting the
debugfs options. Split this out to make it a separate option.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we no longer allow live kernel PMDs to be split, it is safe to
start using the contiguous bit for kernel mappings. So set the contiguous
bit in the kernel page mappings for regions whose size and alignment are
suitable for this.
This enables the following contiguous range sizes for the virtual mapping
of the kernel image, and for the linear mapping:
granule size | cont PTE | cont PMD |
-------------+------------+------------+
4 KB | 64 KB | 32 MB |
16 KB | 2 MB | 1 GB* |
64 KB | 2 MB | 16 GB* |
* Only when built for 3 or more levels of translation. This is due to the
fact that a 2 level configuration only consists of PGDs and PTEs, and the
added complexity of dealing with folded PMDs is not justified considering
that 16 GB contiguous ranges are likely to be ignored by the hardware (and
16k/2 levels is a niche configuration)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation of adding support for contiguous PTE and PMD mappings,
let's replace 'block_mappings_allowed' with 'page_mappings_only', which
will be a more accurate description of the nature of the setting once we
add such contiguous mappings into the mix.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we take care not manipulate the live kernel page tables in a
way that may lead to TLB conflicts, the case where a table mapping is
replaced by a block mapping can no longer occur. So remove the handling
of this at the PUD and PMD levels, and instead, BUG() on any occurrence
of live kernel page table manipulations that modify anything other than
the permission bits.
Since mark_rodata_ro() is the only caller where the kernel mappings that
are being manipulated are actually live, drop the various conditional
flush_tlb_all() invocations, and add a single call to mark_rodata_ro()
instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We expect arch_teardown_dma_ops() to be called very late in a device's
life, after it has been removed from its bus, and thus after the IOMMU
bus notifier has run. As such, even if this funny little check did make
sense, it's unlikely to achieve what it thinks it's trying to do anyway.
It's a residual trace of an earlier implementation which didn't belong
here from the start; belatedly snuff it out.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Kprobes does not need its own homebrewed (and frankly inscrutable) sign
extension macro; just use the standard kernel functions instead. Since
the compiler actually recognises the sign-extension idiom of the latter,
we also get the small bonus of some nicer codegen, as each displacement
calculation helper then compiles to a single optimal SBFX instruction.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a sysfs cpu_capacity attribute with which it is possible to read and
write (thus over-writing default values) CPUs capacity. This might be
useful in situations where values needs changing after boot.
The new attribute shows up as:
/sys/devices/system/cpu/cpu*/cpu_capacity
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the introduction of cpu capacity-dmips-mhz bindings, CPU capacities
can now be calculated from values extracted from DT and information
coming from cpufreq. Add parsing of DT information at boot time, and
complement it with cpufreq information. Also, store such information
using per CPU variables, as we do for arm.
Caveat: the information provided by this patch will start to be used in
the future. We need to #define arch_scale_cpu_capacity to something
provided in arch, so that scheduler's default implementation (which gets
used if arch_scale_cpu_capacity is not defined) is overwritten.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit efd9e03fac ("arm64: Use static keys for CPU features")
introduced support for static keys in asm/cpufeature.h, including
linux/jump_label.h. When CC_HAVE_ASM_GOTO is not defined, this causes a
circular dependency via linux/atomic.h, asm/lse.h and asm/cpufeature.h.
This patch moves the capability macros out out of asm/cpufeature.h into
a separate asm/cpucaps.h and modifies some of the #includes accordingly.
Fixes: efd9e03fac ("arm64: Use static keys for CPU features")
Reported-by: Artem Savkov <asavkov@redhat.com>
Tested-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a CPU clock to every CPU node and CPU OPP tables to use the
generic cpufreq driver. All the CPUs in each cluster share the
same OPP table.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At the first system bring-up, I chose to use spin-table because ARM
Trusted Firmware was not ready for this platform at that moment.
Actually, these SoCs are equipped with EL3 and able to provide PSCI.
Now I finished porting the ATF BL31 for the UniPhier platform, so it
is ready to migrate to PSCI enable method.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Architecturally, TLBs are private to the (physical) CPU they're
associated with. But when multiple vcpus from the same VM are
being multiplexed on the same CPU, the TLBs are not private
to the vcpus (and are actually shared across the VMID).
Let's consider the following scenario:
- vcpu-0 maps PA to VA
- vcpu-1 maps PA' to VA
If run on the same physical CPU, vcpu-1 can hit TLB entries generated
by vcpu-0 accesses, and access the wrong physical page.
The solution to this is to keep a per-VM map of which vcpu ran last
on each given physical CPU, and invalidate local TLBs when switching
to a different vcpu from the same VM.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2E
board. TM2E board is very similar to the TM2 board so the
exynos5433-tm2e.dts includes the TM2 DTS and overrides the differences.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for on board SPI EEPROM by setting
CONFIG_EEPROM_AT25=m
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There is a 'cpu-id' field in efuse, export it for other drivers
reference.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
No need for it - we only use struct bio_vec in prototypes and already have
forward declarations for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The devicetree node for mt8173-auxadc lacks the clock and
io-channel-cells property. This leads to a non-working driver.
mt6577-auxadc 11001000.auxadc: failed to get auxadc clock
mt6577-auxadc: probe of 11001000.auxadc failed with error -2
Fix these fields to get the device up and running.
Fixes: 748c7d4de4 ("ARM64: dts: mt8173: Add thermal/auxadc device
nodes")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
1. Addition of SMMU(MMU-401) device nodes mainly to assist other
developments and testing
2. Addition of CPU dmips/capacity information on all the Juno boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PFTb
-----END PGP SIGNATURE-----
Merge tag 'juno-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64
ARMv8 Vexpress/Juno DT updates for v4.10
1. Addition of SMMU(MMU-401) device nodes mainly to assist other
developments and testing
2. Addition of CPU dmips/capacity information on all the Juno boards
* tag 'juno-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: add cpu capacity-dmips-mhz information to R2 boards
arm64: dts: juno: add cpu capacity-dmips-mhz information to R1 boards
arm64: dts: juno: add cpu capacity-dmips-mhz information to R0 boards
arm64: dts: juno: Add SMMUs device nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYExViEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGwZggA
tK2vjkNsdbFGHscpOxzzMX3ck1tcTgHdFZY/0kgBW6yRm1/FnqP1JW20P2QIthI3
ax1U4m7xDzoS089UndkyHQnHd0ZaUV2htCrocih91QST6Og24atCiyvPSIR58Qbs
EpMNJhbXFVctJarUxdrsCMF0jl2AxxD9euPDhjkYiXLZ0tmdIWZXQUmafmGKviWs
EytssiPPs4fUOOymqKv3kMw2OoTmrTlSNMXpWWDguTPn5p2mDlHOwbJKlgyz8c4x
HAYM56Ad4S0bJyOtraVcPrwfB6gQ321Qs+JfPBR3YJgt1EIjzgeG+W5TYLezXYDu
h1/FnJqU6yrlos+NSIptxQ==
=KA/s
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Hfed
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYDhQ/AAoJEFBXWFqHsHzOjK8H/0BpUb5J1q+ULcJr5boRoErh
LIILJA3q0voOXjONRhOcUx8d3yVccR4AFDsMxP3fzfzDvHrNJcK0ldqMg2I/TvL9
0hUt/IDxSoQ4dCtuuMpWMATeAiUGzCebxKfg12stB+wXUALD7upBrLNP509/Vifw
O8xhPW5w5nWJ5g72QHpDQIqG0Le0Lf4lhuvPsS/hYOeL6mkGVfDTRMOduM3n3KLd
YSMj9NuG1IH9f4xKxGVcs/2ZPdNk+t0PfP/NuPIY3S0qtWwkJRQSPV314WEsxDff
pSCD/KhtkWf8VsHbOgiZUKXPQEsUuKLpqnjjkuF2Sm9KmYCgvaXfLfyX2eyyMN8=
=Xh9e
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
Thierry Reding