This driver allows to provide DT clocks for clock gates found on
Marvell Dove and Kirkwood SoCs. The clock gates are referenced by
the phandle index of the corresponding bit in the clock gating control
register to ease lookup in the datasheet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add Armada 370/XP specific CPU clocks
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds Device Nodes for SATA and SATA PHY device.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
[kgene.kim@samsung.com: removed address definitions as per comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.
v2 patch mods
--------
- Remove l2x0_of_init call as there were problems with the code.
A separate patch will be submitted with cache init code
- Rename capri files and refs to bcm281xx-based names
- Add bcm281xx binding doc
- various misc cleanups
v3 patch mods
-------------
- Remove extra #include lines
- Remove remaining references to capri
- dt uart chipset string added
- cleaned up chip # references
v4 patch mods
-------------
- swap order of compatible definitions for uart
- fix typo
v5 patch mods
-------------
- Rename bcm281xx to bcm11351 in dts+code,
leaving references to bcm281xx only in help+comments.
v6 patch mods
-------------
- fix typo in uart 'compatible' string
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/FbB
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
These changes add DT boot support to DaVinci DA850
SoC.
* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: generate dtbs for da850 boards
ARM: davinci: add support for am1808 based EnBW CMC board
ARM: davinci: da850 evm: add DT data
ARM: davinci: da850: add SoC DT data
ARM: davinci: da850: add DT boot support
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting through a device tree, the kernel cpu logical id map can be
initialized using device tree data passed by FW or through an embedded blob.
This patch adds a function that parses device tree "cpu" nodes and
retrieves the corresponding CPUs hardware identifiers (MPIDR).
It sets the possible cpus and the cpu logical map values according to
the number of CPUs defined in the device tree and respective properties.
The device tree HW identifiers are considered valid if all CPU nodes contain
a "reg" property, there are no duplicate "reg" entries and the DT defines a
CPU node whose "reg" property matches the MPIDR[23:0] of the boot CPU.
The primary CPU is assigned cpu logical number 0 to keep the current convention
valid.
Current bindings documentation is included in the patch:
Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.
The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds device tree support for charging algorithm driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for ab8500-charger driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for battery-temperature-monitor driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- This patch adds device tree support for fuelgauge driver
- optimize bm devices platform_data usage and of_probe(...)
Note: of_probe() routine for battery managed devices is made
common across all bm drivers.
- test status:
- interrupt numbers assigned differs between legacy and FDT mode.
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch extends the driver with any necessary SoC-specific
definitions to support EXYNOS4X12 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Based on AT91 PIT DT patch from Jean-Christophe PLAGNIOL-VILLARD.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
SPEAr platform provides a provision to control chipselects of ARM PL022
Prime Cell spi controller through its system registers, which otherwise
remains under PL022 control which some protocols do not want.
This commit intends to provide the spi chipselect control in software over
gpiolib interface. spi chip drivers can use the exported gpiolib interface to
define their chipselect through DT or platform data.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This hooks the Integrator/CP into the SoC bus when booting from
device tree, by mapping the CP controller registers first,
then registering the SoC device, and then populating the device
tree with the SoC device as parent.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra RTC maintains seconds and milliseconds counters, and five alarm
registers. The alarms and other interrupts may wake the system from
low-power state.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra timer provides a number of 29-bit timer channels, a single
32-bit free running counter, and in the Tegra30 variant, 5 watchdog modules.
The first two channels may also trigger a legacy watchdog reset.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use a better name for the USB PHY clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There are also a few imx6 improvement patches in there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQpeRkAAoJEFBXWFqHsHzOHMoH/3pxLWMHlaFFN70gm33GIEpj
6/P0afKhjEseQDfbvLPfRPwHTQIkw/xQ2rfSrZGUnhgAGN2SfOcxiREFpdChgqyb
b5kO+3oQpnQTFce6tuqCI8j4LAqr63AHhJPWZuDEBaR52Vs0i9gYr2Zwv7i+iUh7
fuLu+NDQLKOkEW7W97FRFVWKRGmSMhJYvhNn+kgleFUhvzUKpJ6n7kFsT05BSl97
EiJHtVxOv+RtlFvx7jrTr18NM2i4Kb4IzEfLzgYOowK9cwfNuhnaxsQvAUiGSa+z
EuvXdKN2btW0PtqHVBPdz5T0OzTyJheaCETKTqz0XM32/SVz5Ma3gZEEDagGLiw=
=zBAI
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch. Most of them are dts changes.
There are also a few imx6 improvement patches in there.
* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: select ARM and PL310 errata
ARM: imx6q: print silicon version on boot
ARM i.MX dts: Consistently add labels to devicenodes
ARM: dts: imx6q-sabresd: add volume up/down gpio keys
ARM: dts: imx53: pinctl update
ARM: imx: enable cpufreq for imx6q
ARM: dts: imx6q: enable snvs lp rtc
ARM: dts: imx6q-sabreauto: Add basic support
ARM: imx6q: let users input debug uart port number
ARM: dts: imx53-qsb: Make DA9053 regulator functional
ARM: dts: imx53-qsb: Use pinctrl for gpio-led
ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CFfP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for 3.8
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
Add device tree file for the armadeus apf27
ARM i.MX: Add Ka-Ro TX25 devicetree
ARM i.MX25: Add devicetree
ARM i.MX25: Add devicetree support
ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
based on imx-multiplatform branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=P3UZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX SoC updates
based on imx-multiplatform branch.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX51 babbage: Add display support
ARM i.MX6: Add IPU support
ARM i.MX51: Add IPU support
ARM i.MX53: Add IPU support
ARM i.MX5: switch IPU clk support to devicetree bindings
ARM i.MX6: fix ldb_di_sel mux
ARM i.MX51: setup MIPI during startup
mx2_camera: Fix regression caused by clock conversion
ARM: clk-imx27: Add missing clock for mx2-camera
ARM i.MX27: Fix low reference clock path
ARM: dts: imx27-3ds: Remove local watchdog inclusion
watchdog: Support imx watchdog on SOC_IMX53
ARM: mach-imx: Support for DryIce RTC in i.MX53
ARM : i.MX27 : split code for allocation of ressources of camera and eMMA
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested on an at91sam9260 board (evk-pro3)
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch contains a new network driver for the network unit of the
ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B
processor, a Marvell-developed ARM core that implements the ARMv7
instruction set.
Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery),
the network unit in Armada 370 and Armada XP is highly different. This
is the reason why this new 'mvneta' driver is needed, while the older
ARM Marvell SoCs use the 'mv643xx_eth' driver.
Here is an overview of the most important hardware changes that
require a new, specific, driver for the network unit of Armada 370/XP:
- The new network unit has a completely different design and layout
for the RX and TX descriptors. They are now organized as a simple
array (each RX and TX queue has base address and size of this
array) rather than a linked list as in the old SoCs.
- The new network unit has a different RXQ and TXQ management: this
management is done using special read/write counter registers,
while in the Old SocS, it was done using the Ownership bit in RX
and TX descriptors.
- The new network unit has different interrupt registers
- The new network unit way of cleaning of interrupts is not done by
writing to the cause register, but by updating per-queue counters
- The new network unit has different GMAC registers (link, speed,
duplex configuration) and different WRR registers.
- The new network unit has lots of new units like PnC (Parser and
Classifier), PMT, BM (Memory Buffer Management), xPON, and more.
The driver proposed in the current patch only handles the basic
features. Additional hardware features will progressively be supported
as needed.
This code has originally been written by Rami Rosen
<rosenr@marvell.com>, and then reviewed and cleaned up by Thomas
Petazzoni <thomas.petazzoni@free-electrons.com>.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers. There are two reasons to have a separate
driver rather than including it inside the MAC driver itself:
*) The MDIO interface is shared by all Ethernet ports, so a driver
must guarantee non-concurrent accesses to this MDIO interface. The
most logical way is to have a separate driver that handles this
single MDIO interface, used by all Ethernet ports.
*) The MDIO interface is the same between the existing mv643xx_eth
driver and the new mvneta driver. Even though it is for now only
used by the mvneta driver, it will in the future be used by the
mv643xx_eth driver as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
linux,mtd-name allow to specify the mtd name for retro capability with
physmap-flash drivers as boot loader pass the mtd partition via the old
device name physmap-flash.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
[wsa: fixed some whitespace]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
convert at91sam9g20ek with wm8731 to device tree support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.
SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This driver supports GRCAN and CRHCAN CAN controllers available in the GRLIB
VHDL IP core library.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enhance the driver to support partition subnodes inside the nand
device bindings to describe partions on the nand device.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
various .dts files, and timer related changes to allow
configuring the timer via device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=59qq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:
Device tree related changes for omaps updating the
various .dts files, and timer related changes to allow
configuring the timer via device tree.
* tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (48 commits)
usb: musb: dsps: dt binding - add resources, example
ARM: dts: omap4-sdp: Add pinmux configuration for HDMI
ARM: dts: omap4-panda: Add pinmux configuration for HDMI
ARM: dts: Makefile: Add the am335x-evmsk target in dtbs list
ARM: dts: AM33XX: Add usbss node
ARM: dts: AM33XX: Add push-buttons device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-keys to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-leds to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-bone
ARM: dts: AM33XX: Add pinmux configuration for user-leds to BONE
ARM: dts: AM33XX: Add volume-keys device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for volume-keys to EVM
ARM: dts: AM33XX: Add matrix keypad device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for matrix keypad to EVM
ARM: dts: omap5-evm: LPDDR2 memory device details for EVM
ARM: dts: omap5: EMIF device tree data for OMAP5 boards
ARM: dts: omap5-evm: Fix size of memory defined for EVM
ARM: OMAP2+: Add device-tree support for 32kHz counter
ARM: OMAP: Add DT support for timer driver
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This driver is based on the thermal management framework in thermal_sys.c. A
thermal zone device is created with the trip points to which cooling devices
can be bound, the current cooling device is cpufreq, e.g. CPU frequency is
clipped down to cool the CPU, and other cooling devices can be added and bound
to the trip points dynamically. The platform specific PRCMU interrupts are
used to active thermal update when trip points are reached.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Instead of having a host of different register offsets in the device tree,
this patch simplifies the CPSW code by letting the driver set the proper
register offsets automatically, based on the CPSW version.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide simplified models for the necessary clocks on the zynq-7000
platform. Currently, the PLLs, the CPU clock network, and the basic
peripheral clock networks (for SDIO, SMC, SPI, QSPI, UART) are modelled.
OF bindings are also provided and documented.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
A selection of voltage or current values (AKA states) should always
be specified when using a GPIO regulator. If there are no switchable
states then the fixed regulators should be used instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
0384e90b8 ("spi/mcspi: allow configuration of pin directions") did what
it claimed to do the wrong way around. D0/D1 is configured as output by
*clearing* the bits in the conf registers, hence also breaking the
former default behaviour.
Fix this before that change is merged to mainline.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
NVIDIA's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add the spi driver for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Wrong description in binding document.
Doc use "gpio-enable", but code use "enable-gpio"
In drivers/regulator/gpio-regulator.c
config->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0);
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Patches from Roland Stigge <stigge@antcom.de>:
Platform topic branch for lpc32xx
* 'lpc32xx/core' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add the motor PWM clock
ARM: LPC32xx: Cleanup irq.c
ARM: LPC32xx: Relocate calls to irq_set_chained_handler()
ARM: LPC32xx: Remove superfluous irq_alloc_descs()
Includes an update to v3.7-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a i.MX25 dtsi file along with the i.MX25 clock tree
documentation. The devicetree should be fairly complete for:
- uart
- fec
- i2c
- spi
- pwm
- nand
- gpio
- wdog
- esdhc
- flexcan
The more exotic devices currently miss clock bindings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tr2i
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB musb merge from Felipe:
"usb: musb: patches for v3.8 merge window
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read."
Here we add the required documentation for the STMPE Multi-Functional
Device (MFD) Device Tree bindings. It describes all of the bindings
currently supported by the driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
pinctrl subsystem needs gpio chip base to prepare set of gpio
pin ranges, which a given pinctrl driver can handle. This is
important to handle pinctrl gpio request calls in order to
program a given pin properly for gpio operation.
As gpio base is allocated dynamically during gpiochip
registration, presently there exists no clean way to pass this
information to the pinctrl subsystem.
After few discussions from [1], it was concluded that may be
gpio controller reporting the pin range it supports, is a
better way than pinctrl subsystem directly registering it.
[1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
[Edited documentation a bit]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The used vendor prefix corresponds to the stock symbol (ONNN) for ON
Semiconductor Corp.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
remove linux specific references, enumerates all supported
regulators
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DT bindings normally use '-' (hyphens) instead of '_' (underscore),
driver has it the proper way, but binding documentation does not
reflect it, fix it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQlr0MAAoJEHm+PkMAQRiGLVQH/171fUorGn+u2k7dNhSWJXHB
pPy6MbZhuBWepgRZGS0ffiC5tBvQaf9iK9Fh/9aqrDDw2aELk0CLPqQcfAUF/Jzf
USPdBSIMNikgZtlWhabxuj/zKdaw8UuiJpCf3rMyIRmjQgmZyw/53TEqF54xTv0I
Y4Y21vTSVXilQwvwYvcsCEBFrTZqXjLWQ60Hk+QRS9GV7a9m2LFcdiPOtRv17gbd
CBDuiMHN9R04l2bB+5WHHsu+TNNf5uy3wAgEskDTftneXWjW44R4UR8O0rQh1ezQ
Pa5WpCyJRRG8UOtPKTS6LEbljBwLLIoVI2JRoJrWoy3OkT63wyowFXyLGWCCrHY=
=qAGi
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc4' into next to sync up Wacom bits
Linux 3.7-rc4
OMAP2+ family of devices are now obtaining resources via DT, earlier
it was obtained from hwmod. Update binding document accrodingly, while
at it add example.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add atmel-ssc for device tree support
Match "atmel,at91rm9200-ssc" for using pdc for data transfer
Match "atmel,at91sam9g45-ssc" for using dma for data transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
From Lee Jones:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500: (31 commits)
ARM: ux500: Convert DT_MACHINE_START to use SMP operations
ARM: ux500: CONFIG: Enable GPIO Regulators
ARM: ux500: Change the type of interrupt to something compatible
ARM: ux500: Add node for the MMC GPIO regulator
ARM: ux500: List DT compatibility using platform names rather than by board
ARM: ux500: Remove duplicate DT_MACHINE_START - make u8500 for generic
ARM: ux500: Rename references to the ccu9540 dev board accordingly
ARM: ux500: Enable all MMC devices on the u9540 when booting with DT
ARM: ux500: Enable SDI4 port on the u9540 when booting with Device Tree
ARM: ux500: Add UART support to the u9540 Device Tree
ARM: ux500: Add support for ST-Ericsson's u9540 SoC
ARM: ux500: Add skeleton DTS file for the u9540
ARM: ux500: Remove unused board compatible string
ARM: ux500: Supply the STMPE keypad Device Tree node to the STUIB DT
ARM: ux500: Apply a Device Tree node for the STMPE MFD
ARM: ux500: Stop informing the regulator subsystem that we have full constraints
ARM: ux500: Add all bu21013 touch screen components to supported Device Trees
ARM: ux500: Stop calling the UIB init function when using Device Tree
ARM: ux500: Create a new Device Tree include file for boards supporting STUIBs
Documentation: Detail permitted DT properties for the BU21013 Touch Screen
...
The way the VE motherboard Device Trees were constructed
enforced naming and structure of daughterboard files. This
patch makes it possible to simply include the motherboard
description anywhere in the main Device Tree and retires
the "arm,v2m-timer" alias - any of the motherboard SP804
timers will be used instead.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This is a platform driver for Versatile Express' "system
register" block. It's a random collection of registers providing
the following functionality:
- low level platform functions like board ID access; in order to
use those, the driver must be initialized early, either statically
or based on the DT
- config bus bridge via "system control" interface; as the response
from the controller does not generate interrupt (yet), the status
register is periodically polled using a timer
- pseudo GPIO lines providing MMC card status and Flash WP#
signal control
- LED interface for a set of 8 LEDs on the motherboard, with
"heartbeat", "mmc0" and "cpu0" to "cpu5" as default triggers
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Versatile Express platform has an elaborated configuration system,
consisting of microcontrollers residing on the mother- and
daughterboards known as Motherboard/Daughterboard Configuration
Controller (MCC and DCC). The controllers are responsible for
the platform initialization (reset generation, flash programming,
FPGA bitfiles loading etc.) but also control clock generators,
voltage regulators, gather environmental data like temperature,
power consumption etc. Even the video output switch (FPGA) is
controlled that way.
Those devices are _not_ visible in the main address space and
the usual communication channel uses some kind of a bridge in
the peripheral block sending commands (requests) to the
controllers and receiving responses. It can take up to
500 microseconds for a transaction to be completed, therefore
it is important to provide a non-blocking interface to it.
This patch adds an abstraction of this infrastructure. Bridge
drivers can register themselves with the framework. Then,
a driver of a device can request an abstract "function" - the
request will be redirected to a bridge referred by thedd
"arm,vexpress,config-bridge" property of the device tree node.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
A very simple binding, the only property is the phandle to the PWM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the cpsw driver to operate correctly with both the
dm814x and the am335x versions of the switch hardware.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates pwm-vt8500.c to support devicetree probing and
make use of the common clock subsystem.
A binding document describing the PWM controller found on
arch-vt8500 is also included.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Here we apply required documentation for the Rohm BU21013 Touch
Screen driver which describe available properties and how to use
them.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Separate out common dts pieces from highbank dts and add support for
Calxeda ECX-2000 (Midway) SOC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQjYaSAAoJEHm+PkMAQRiGIlYH+wbwj7i5CcUG46VRFT5WlG7W
iYaojL68FKKIUCBh4GOvZxE2D907KgqHQI6rePE/xDhK493d0Nyi4PGQJ1JoTE+l
JQq++C3CoX9mm/zCRW5JyOcemE4t2t1/poi2ege9Kf9E9N5Cw0P4r8Cz1urCFKL6
EO2/gA5d6cBQpg+gVq9T88SnYgiJGs7d8AYjFeC7SrqIwDvG6tfg+YF4IRxC4QAc
0zbBgej/kbuiLbGl2ltU0I9HTOwlTgp53tdYe810cs3CdzNC2ykdF391Q24tloeo
uxmCSQrA2upHA9aILqY+T5f+cMOpVS4T8Ica3N9OzVEIPXSh2K9d4tESGPikMEE=
=yiDr
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc3' into next to sync up with recent USB and MFD changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQjYaSAAoJEHm+PkMAQRiGIlYH+wbwj7i5CcUG46VRFT5WlG7W
iYaojL68FKKIUCBh4GOvZxE2D907KgqHQI6rePE/xDhK493d0Nyi4PGQJ1JoTE+l
JQq++C3CoX9mm/zCRW5JyOcemE4t2t1/poi2ege9Kf9E9N5Cw0P4r8Cz1urCFKL6
EO2/gA5d6cBQpg+gVq9T88SnYgiJGs7d8AYjFeC7SrqIwDvG6tfg+YF4IRxC4QAc
0zbBgej/kbuiLbGl2ltU0I9HTOwlTgp53tdYe810cs3CdzNC2ykdF391Q24tloeo
uxmCSQrA2upHA9aILqY+T5f+cMOpVS4T8Ica3N9OzVEIPXSh2K9d4tESGPikMEE=
=yiDr
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc3' into for-linus to sync up with recent USB changes
Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.
Add documentation for timer properties specific to OMAP.
Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.
V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
HWMOD.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Update i2c trivial-devices list by adding the description for
ti,tmp275 temperature sensor and taos,tsl2550 ambient light
sensor.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
This patch adds support for device tree based discovery for exynos5
hdmi ddc.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
hdmiphy.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
mixer. Mixer node is also renamed with "exynos5-mixer".
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree based discovery for exynos5
hdmi. Hdmi node is also renamed with "exynos5-hdmi".
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This board supports:
- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support
This patch adds the basic DTS file enabling the serial ports.
Other features will be added in due course of time.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
[nsekhar@ti.com: modified after dtsi refactoring and added binding
documentation]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for booting DA850 using flattened device
tree to describe the hardware. At this time only the
very basic bootup using a serial console is supported.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
The list of attributes above details the use of the 'filter-ranges'
property, but the example improperly used 'filter-latency'. Make these
consistent by fixing up the example.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Implement the machine restart hook using the SoC's watchdog timer module.
To support this, define a DT binding for the watchdog module, and add it
to the device tree.
The downstream rpi-split branch contains a full watchdog timer driver
implementation, which also implements the restart hook. However, the
restart function is largely separate from the watchdog driver, so for
simplicity, the restart hook is implemented here directly in the main
machine source file.
Overall structure (separate setup/restart) functions derived from the
picoxcell ARM support.
Watchdog register IO sequence taken from code by Simon Arlott. Note that
the watchdog module is not documented in BCM2835-ARM-Peripherals.pdf.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The irq_to_gpio() is old, most platforms use GENERIC_GPIO framework
and don't support this API anymore.
The i.MX6q sabrelite platform equips an egalax touchscreen controller,
and this platform already transfered to GENERIC_GPIO framework, to
support this driver, we use a more generic way to get gpio.
Add a return value checking for waking up the controller in the probe
function, this guarantee only a workable device can pass init.
[dmitry.torokhov@gmail.com: Make driver depend on CONFIG_OF as it is
now required.]
Acked-by Zhang Jiejing <jiejing.zhang@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds device tree entry for MFC v6 in the Exynos5
SoC. Makes the required changes in the clock files and adds
MFC to the DT device list.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[kgene.kim@samsung.com: fixed section mismatches Seung-Woo Kim reported]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Here we provide the GPIO Regulator driver with Device Tree capability, so
that when a platform is booting with DT instead of platform data we can
still make full use of it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow D0 to be an input and D1 to be an output, configurable via
platform data and a new DT property.
Based on a patch from Matus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
The CS4271 has a feature to sync its analog mute flags, so one mute
circuitry can be used for both channels.
Give users access to this feature with a new DT property and a flag in
the platform data.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.
This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On the at91sam9x5 SoC series, GPIO banks B and D only have 19 and 22
pins. So add a property to set this parameter.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQcpeWAAoJEGwxgFQ9KSmkpi4P/2etDDz5aEkEHNa1l4xEmFcm
ymiGTgjaalqpUAVbM/gYx9G59EFMEbzUl1BHAqE5La4wO/v9lNPb+VrdUo+B+NZ7
WSxIPWcNqdinSuoSqyYPjoPMVnhs3EMtNOqmf4jm1JOvdqA+4rO29xQVAqK/5Gfu
LpMOyPiRi5ODnbQ1BOIWwpKICioY/mLwGJudK3z0i/fYVA7gLub20f+w+sOjKIA4
wmwQAMTjAR798Cg/tVy4fQmf4SLw+c2nIgGe/PD+2gVlGXLNKBrJfMonHPTbmwKu
lmJO/EtnijNOnpbn6up7ryUQ9cSoZAUZOfdIOgmAeQgQ/LWR0f+zf2IQehSPwrul
g6hqOnQI2DNN7ugT3cYVbYnsh56TjyhnxhhxZgkapqh706QkqHGyKJNMRetzuXmP
1O//MnZJrFQWd6sOKLlTL2ZzRvnxEJcNVGaE6bbwZTfQMtPeo9l1842uIq1dLUtG
VxZb/svKUkMXv4is1dwUYUkpDsKxsgMEmabmuovceGf2N7jj/irkXgqxf6LWkaY1
JQ7ZFWUJyDzEMXRaFfzdGO15T532CfB84wvFX5xoPMwMste2AA7QuybFBVstXhKu
AtKNDgRJFUTlnLIxydpPBWdWH3UJdEaFwwsSfuNKI8OmmGKhWC/aP83k4hzueu9H
KYLvY/0ObMSMqiwh/ndQ
=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
[wsa: rebased to 3.6-rc7]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
clk_{un}prepare is mandatory for platforms using common clock framework.
Since this driver is used by SPEAr platform, which supports common clock
framework, add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds simple DT bindings for SDHCI SPEAr controller. It uses cd-gpios
from common mmc bindings.
This also fixes spear300-evb.dts with correct name for card detect binding.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The compatible value shouldn't include ".txt", which was probably cut
and paste from the filename.
Reported-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQblIiAAoJEIwa5zzehBx3J1EP/1pxMqjVKQDXxak+A6g8a7r0
hUTjqfiA9nZ4st+nk3PKJL9DNkoTEoZZqXghYRA+N6ej4hAaFJX1izgQDtjtjfRE
s2izZuxGka8Oiic6FpCUoQnMORg10tSLgyvlHNW4hXy3qpe2C4u1D2GJwA/GPeLQ
lHREekcJ3RKWutpG2hMtCT+9Bm4AwnnMY5uO39gxoXeMn6RoaACNIyYxz0NeL5bV
GDuawi7Pc4KJTXX+D/VU0o7VtksiUO8YBczFEra/9khSL/RI2PFalIX3DKiioqvA
yUA11d9proqojIdfdjVRPBHnIMl49H8ohBwbQfKnkNz9msl1BKN5PbakKls97mQ+
vaJpoACnc/3x4P/izEpwry5XqeIl5S5mwz4R4+fojpWpp4JPcly/cAKMAsXf5WRi
NF50E4D/8ysHE8WuBU5YHFgEEbn3nXkRbNMgdYtUwzixdmNJNaU8+33BJo34c4j0
DNktiEdKUBoiiEdsC1MgH86olD/sFNUxvXBub30hhOywoapgQE61fGQGxG38DV/K
kspTHz9SKUrmgbYEyMNOhz4paRrheYxx9cAgKP7Hp7m4Gu8d6ZqRqLqN9hbAbLuW
TbH2FpqcjSw4KnYYCepTixJ3dhGiICiILWHfsW3qCj5Le3YVwedCpBCL1/I+RqEP
kYTToVhur/T1yamHAmBi
=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
The second cell in the PWM specifier denotes the period in nanoseconds,
not the duty cycle. The latter can be freely configured at runtime and
a PWM with a fixed duty cycle would be rather pointless.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau@advansee.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions).
PV console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQbJELAAoJEFjIrFwIi8fJSI4H/32qrQKyF5IIkFKHTN9FYDC1
OxEGc4y47DIQpGUd/PgZ/i6h9Iyhj+I6pb4lCevykwgd0j83noepluZlCIcJnTfL
HVXNiRIQKqFhqKdjTANxVM4APup+7Lqrvqj6OZfUuoxaZ3tSTLhabJ/7UXf2+9xy
g2RfZtbSdQ1sukQ/A2MeGQNT79rh7v7PrYQUYSrqytjSjSLPTqRf75HWQ+eapIAH
X3aVz8Tn6nTixZWvZOK7rAaD4awsFxGP6E46oFekB02f4x9nWHJiCZiXwb35lORb
tz9F9td99f6N4fPJ9LgcYTaCPwzVnceZKqE9hGfip4uT+0WrEqDxq8QmBqI5YtI=
=gxJD
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull ADM Xen support from Konrad Rzeszutek Wilk:
Features:
* Allow a Linux guest to boot as initial domain and as normal guests
on Xen on ARM (specifically ARMv7 with virtualized extensions). PV
console, block and network frontend/backends are working.
Bug-fixes:
* Fix compile linux-next fallout.
* Fix PVHVM bootup crashing.
The Xen-unstable hypervisor (so will be 4.3 in a ~6 months), supports
ARMv7 platforms.
The goal in implementing this architecture is to exploit the hardware
as much as possible. That means use as little as possible of PV
operations (so no PV MMU) - and use existing PV drivers for I/Os
(network, block, console, etc). This is similar to how PVHVM guests
operate in X86 platform nowadays - except that on ARM there is no need
for QEMU. The end result is that we share a lot of the generic Xen
drivers and infrastructure.
Details on how to compile/boot/etc are available at this Wiki:
http://wiki.xen.org/wiki/Xen_ARMv7_with_Virtualization_Extensions
and this blog has links to a technical discussion/presentations on the
overall architecture:
http://blog.xen.org/index.php/2012/09/21/xensummit-sessions-new-pvh-virtualisation-mode-for-arm-cortex-a15arm-servers-and-x86/
* tag 'stable/for-linus-3.7-arm-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (21 commits)
xen/xen_initial_domain: check that xen_start_info is initialized
xen: mark xen_init_IRQ __init
xen/Makefile: fix dom-y build
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
...
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
- Import of latest upstream device tree compiler (dtc)
- New function of_get_child_by_name
- Support for #size-cells of 0 and #addr-cells of >2
- Couple of DT binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQbF9eAAoJEMhvYp4jgsXiMVAH/3AsqH/ksWFO48L2342WhPzv
JLP2YJQ+X2E3fi4sIXWDOAHXgSsKcKYiUqRJNpebdAzfK+/HCdtV594GXP9MfUdq
05ByUBa728wNPHiQitbtwLu+MN0ot1icXeHB+Gx8LuVrJnW/iJv/FHa6QU+cc9ct
jxnDu8Lfp4ja4rFWq56c5vda6ecP5nVIyAPZ40z9Q6QioL0BxJ4axQ8mW6lxG0SH
BxOzCppxxShU3O52typ29UORfTDfFPFmskLuJPxGThI4HWaIfpBc55wKKw8P2SR0
2/uK+TJw/UTsDwB/IIzbane4AIScj7ZdRjN1T132DcX9e/aDaZhDMNoG3TSE6kQ=
=CZiW
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.7' of git://sources.calxeda.com/kernel/linux
Pull devicetree updates from Rob Herring:
- Import of latest upstream device tree compiler (dtc)
- New function of_get_child_by_name
- Support for #size-cells of 0 and #addr-cells of >2
- Couple of DT binding documentation updates
Fix up trivial conflicts due to of_get_child_by_name() having been added
next to the new of_get_next_available_child().
* tag 'dt-for-3.7' of git://sources.calxeda.com/kernel/linux:
MAINTAINERS: add scripts/dtc under Devicetree maintainers
dtc: import latest upstream dtc
dt: Document general interrupt controller bindings
dt/s3c64xx/spi: Use of_get_child_by_name to get a named child
dt: introduce of_get_child_by_name to get child node by name
of: i2c: add support for wakeup-source property
of/address: Handle #address-cells > 2 specially
DT: export of_irq_to_resource_table()
devicetree: serial: Add documentation for imx serial
devicetree: pwm: mxs-pwm.txt: Fix reg field annotation
of: Allow busses with #size-cells=0
Add device tree based discovery support for Samsung's sdhci controller.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung Exynos SoC's extend the dw-mshc controller for additional clock
and bus control. Add support for these extensions and include provide
device tree based discovery suppory as well.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add device tree based discovery support.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
1) Apply -- and then revert -- the FUA feature. Caused
disk corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=i3EH
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
No framework work here, only a bunch of driver updates of varying sizes:
- Factoring out of the core hardware support from the MXS MMC driver by
Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ld23
-----END PGP SIGNATURE-----
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Pull input updates from Dmitry Torokhov:
"A few drivers were updated with device tree bindings and others got a
few small cleanups and fixes."
Fix trivial conflict in drivers/input/keyboard/omap-keypad.c due to
changes clashing with a whitespace cleanup.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: wacom - mark Intuos5 pad as in-prox when touching buttons
Input: synaptics - adjust threshold for treating position values as negative
Input: hgpk - use %*ph to dump small buffer
Input: gpio_keys_polled - fix dt pdata->nbuttons
Input: Add KD[GS]KBDIACRUC ioctls to the compatible list
Input: omap-keypad - fixed formatting
Input: tegra - move platform data header
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: s3c2410_ts - make s3c_ts_pmops const
Input: samsung-keypad - use of_get_child_count() helper
Input: samsung-keypad - use of_match_ptr()
Input: uinput - fix formatting
Input: uinput - specify exact bit sizes on userspace APIs
Input: uinput - mark failed submission requests as free
Input: uinput - fix race that can block nonblocking read
Input: uinput - return -EINVAL when read buffer size is too small
Input: uinput - take event lock when fetching events from buffer
Input: get rid of MATCH_BIT() macro
Input: rotary-encoder - add DT bindings
Input: rotary-encoder - constify platform data pointers
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by
Lee Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=jbUM
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"So this is the LW GPIO patch stack for v3.7:
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by Lee
Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing."
* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
gpio: pcf857x: select IRQ_DOMAIN
gpio: Document device_node's det_debounce
gpio-lpc32xx: Add GPI_28
gpio: adnp: dt: Reference generic interrupt binding
gpio: Add Avionic Design N-bit GPIO expander support
gpio: pxa: using for_each_set_bit to simplify the code
gpio_msm: using for_each_set_bit to simplify the code
gpio: Enable the tc3298x GPIO expander driver for Device Tree
gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
gpio: pcf857x: fixup smatch WARNING
gpio: 74x164: Add support for the daisy-chaining
gpio: 74x164: dts: Add documentation for the dt binding
dt: Fix incorrect reference in gpio-led documentation
gpio: 74x164: Add device tree support
gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
gpio: 74x164: Use devm_kzalloc
gpio: 74x164: Use module_spi_driver boiler plate function
gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
...
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Some highbank DMA masters can support coherent (ACP) or non-coherent DMA.
This sets up dma_map_ops for masters which are configured for coherent DMA.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaiKNAAoJEIwa5zzehBx329AP/1TwJk1dTHaAA7vDxyz2mq1E
F0MBL9p32R1SczrFGjbmb9ouVW5tTjbK1zted5zBrGBXDIX9Kdz3Dmm7x6b2/JvZ
8yMrdiBNpF3r8au6IaMuMlOq5yAaN+F4SxbC2rE0a9y3YmMZ6ug5dgoZ4O8orAC4
il3eq1sb+rTTPCf7C5cGlKzdRQi2KYdAycpa7ChQCYSamxJjdM7cXR7pohVv9vhd
9sF+h1I0ArxcVYn/mUOoCin8MyIWXlBQvbUnF+3aYO8CO9erhKH/owPngVBWGKZH
+X6dk0ChUJfjzaWr2HPZIYUqLUnIoO8TsRhQVmLp1rPrSzSXMG3iDq0M4WEwL4Xo
bMbAZ1KWYg53HRqbIOEQk5q9Mg7HUgtbJuOE7WLgBO5ubdKFFWLmDUJ+WVcoWzSW
qyWaWpECSptlQjFyqZJd9MjizIDhuYjog2EWaSWXETQ+1XRmCSsqx8AX6n1MVdhP
6jDLnYHYiJoOtGiaDpYxsXgMXdOVsrTegecNduqH/XhdEL1iwy3fwgK1DjoclYoj
iFbn0/Tw3N5SvJlG4xitl12DQ7MeCCbfzJGRKenVh9/O4U+qrTbFRmsNaaZw5dA1
bt+iEZ3aU8YBaKj02LexunAevpZJ2rfGNX2tBjQrIzzZK6CZibPWg42qfKJfdn7w
etXVVApw5jQjAImY64kh
=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen
Warren. It's still early days on mainline support, with just the
basics working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BCp4
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates from Olof Johansson:
"Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen Warren.
It's still early days on mainline support, with just the basics
working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well."
Fix up trivial conflicts with the clk infrastructure changes.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (62 commits)
ARM: shmobile: add new __iomem annotation for new code
ARM: LPC32xx: Support GPI 28
ARM: LPC32xx: Platform update for devicetree completion of spi-pl022
ARM: LPC32xx: Board cleanup
irqchip: fill in empty Kconfig
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
This reverts commit d755998270.
It wasn't meant to be applied, commit
342b7b741d ("net: ti cpsw ethernet: set
IFCTL_A bit in MACCONTROL") was redone in such a way to make this
commit unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to specify the phy interface of the CPSW slaves. The new
node parameter is called "phy_if_mode" and is optional. The original
behaviour of the driver is preserved when not given.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree. There are also the
usual XHCI set of updates, and other various driver changes and updates.
We also are trying hard to remove the old dbg() macro, but the final
bits of that removal will be coming in through the networking tree
before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3+AACgkQMUfUDdst+ym5vwCfe93FyJyXn/RDkGz7iBemvWFd
vrwAoIxjaOa4/yWZWcgrWc5bP4aO3ssc
=jYDr
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB changes from Greg Kroah-Hartman:
"Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree.
There are also the usual XHCI set of updates, and other various driver
changes and updates. We also are trying hard to remove the old dbg()
macro, but the final bits of that removal will be coming in through
the networking tree before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.
* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
USB: uas: fix gcc warning
USB: uas: fix locking
USB: Fix race condition when removing host controllers
USB: uas: add locking
USB: uas: fix abort
USB: uas: remove aborted field, replace with status bit.
USB: uas: fix task management
USB: uas: keep track of command urbs
xhci: Intel Panther Point BEI quirk.
powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
Revert "usb : Add sysfs files to control port power."
USB: serial: remove vizzini driver
usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
Increase XHCI suspend timeout to 16ms
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
USB: sierra_ms: don't keep unused variable
fsl/usb: Add support for USB controller version 2.4
USB: qcaux: add Pantech vendor class match
...
As we skipped the merge window for 3.6-rc1 for the tty tree, everything
is now settled down and working properly, so we are ready for 3.7-rc1.
Here's the patchset, it's big, but the large changes are removing a
firmware file and adding a staging tty driver (it depended on the tty
core changes, so it's going through this tree instead of the staging
tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp36oACgkQMUfUDdst+yk4WgCdEy13hot8fI2Lqnc7W0LKu7GX
4p8AoLTjzrXhLosxdijskDQ9X1OtjrxU
=S5Ng
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Here is the big staging tree update for the 3.7-rc1 merge window.
There are a few patches in here that are outside of the staging area,
namely HID and IIO patches, but all of them have been acked by the
relevant subsystem maintainers. The IIO stuff is still coming in
through this tree as it hasn't entirely moved out of the staging tree,
but is almost there.
Other than that, there wa a ton of work on the comedi drivers to make
them more readable and the correct style. Doing that removed a lot of
code, but we added a new driver to the staging tree, so we didn't end up
with a net reduction this time around:
662 files changed, 51649 insertions(+), 26582 deletions(-)
All of these patches have been in the linux-next tree already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp32YACgkQMUfUDdst+ymU5QCgm8KWB+dAO8ZFbmzhhm3C0VFl
wB0AoKbDj/tCiUHkJ70u/i3OHueKkpet
=ut2/
-----END PGP SIGNATURE-----
Merge tag 'staging-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg Kroah-Hartman:
"Here is the big staging tree update for the 3.7-rc1 merge window.
There are a few patches in here that are outside of the staging area,
namely HID and IIO patches, but all of them have been acked by the
relevant subsystem maintainers. The IIO stuff is still coming in
through this tree as it hasn't entirely moved out of the staging tree,
but is almost there.
Other than that, there wa a ton of work on the comedi drivers to make
them more readable and the correct style. Doing that removed a lot of
code, but we added a new driver to the staging tree, so we didn't end
up with a net reduction this time around:
662 files changed, 51649 insertions(+), 26582 deletions(-)
All of these patches have been in the linux-next tree already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1094 commits)
staging: comedi: jr3_pci: fix iomem dereference
staging: comedi: drivers: use comedi_fc.h cmdtest helpers
Staging: winbond: usb_free_urb(NULL) is safe
Staging: winbond: checkpatch cleanup
Staging: winbond: Removed undesired spaces, lines and tabs
Staging: winbond: Typo corrections in comments
Staging: winbond: Changed c99 comments to c89 comments
staging: r8712u: Do not queue cloned skb
staging: comedi: ni_mio_common: always lock in ni_ai_poll()
staging: comedi: s626: add FIXME comment
staging: comedi: s626: don't dereference insn->data
staging: comedi: s526: fix if() check in s526_gpct_winsn()
staging: comedi: s626: cleanup comments in s626_initialize()
staging: comedi: s626: remove clear of kzalloc'ed data
staging: comedi: s626: remove 'WDInterval' from private data
staging: comedi: s626: remove 'ChargeEnabled' from private data
staging: comedi: s626: remove 'IsBoardRevA' comment
staging: comedi: s626: #if 0 out the "SAA7146 BUG WORKAROUND"
staging: comedi: s626: remove 'allocatedBuf' from private data
staging: comedi: s626: add final attach message
...
Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my tree,
or in Andrew's (the lis3l driver changes came from his tree last week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3pcACgkQMUfUDdst+ymLswCcDYG9RkRcEdYwT5bOm1zM4IVl
WM0AoLKfC86g6xe4MdS7zROJn7ep/9qu
=zAHk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
In order to use a device as interrupt controller, it needs to be marked
with the DT interrupt-controller property. This commit adds rudimentary
documentation about the required standard properties and describes the
most commonly used interrupt specifiers.
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
problems with JFFS2 usage, as the local bus (LPB) doesn't support
unaligned accesses as implemented in the JFFS2 code via memcpy().
By defining "no-unaligned-direct-access", the flash will not be
exposed directly to the MTD users (e.g. JFFS2) any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add OF support for the davinci nand controller.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add lis3lv02d device tree initialization code/API to take pdata from
device node. Also adds device tree init matching table support to
lis3lv02d_i2c driver. If the driver data is passed from device tree, then
this driver picks up platform data from device node through common/generic
lis3lv02d.c driver.
[akpm@linux-foundation.org: fix CONFIG_OF=n build]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds logic to parse lis3 properties from a device tree node and store them
in a freshly allocated lis3lv02d_platform_data.
Note that the actual match tables are left out here. This part should
happen in the drivers that bind to the individual busses (SPI/I2C/PCI).
Also adds some DT bindinds documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Rob Herring <robherring2@gmail.com>
Cc: "AnilKumar, Chimata" <anilkumar@ti.com>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the MAX8907 binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the TPS6586x binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit "regulator: deprecate regulator-compatible DT property" deprecated
the use of the regulator-compatible DT property. Update the DT example in
the TPS65217 binding documentation to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and
However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.
Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.
The code is changed such that old device trees continue to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQVkutAAoJEHm+PkMAQRiGW8sH/36FVQ3zI75QH16AmR++2nMZ
BRJGoxcRFMssrXTYVdkMyzygf8b7MZbNEn1qt2g63MNzGaJucPlw5NVL4GLzR+zr
x/EglLrTEPCD5el9wJ3ls9iC1soudKQTvC2BjcdUjpoSwHrDM/7GKfbOacE54Wqc
C1VHCcg5DWOD7F0RnYT2SQEVCeDODNmcyFdk7Oi4cUicTPJoYWJ9O9MGfBDBok0N
M+dXxa9nvsl7EeEKpBKH9vo4TfXn3Gsj6LCRdedvI15ilZjfo8jdHYbSn7KBfQuZ
JIKRnqkaQ1JfMFt+M/JJZ1b/+Wrd4HLMmmn5oUmrGGIvhpi32nJfi/97+nSy8iU=
=c5gW
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc6' into spi-mxs
Linux 3.6-rc6
Conflicts (overlap between moving code that accesses registers around
and factoring the register access out into a SSP layer):
drivers/mmc/host/mxs-mmc.c
Gregory CLEMENT