The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change hooks link-status-change interrupts to phylib.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdfhttps://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.
v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the integrated 2.5Gbps PHY in Realtek RTL8125.
Advertisement of 2.5Gbps mode is done via a vendor-specific register.
Same applies to reading NBase-T link partner advertisement.
Unfortunately this 2.5Gbps PHY shares the PHY ID with the integrated
1Gbps PHY's in other Realtek network chips and so far no method is
known to differentiate them. As a workaround use a dedicated fake PHY ID
that is set by the network driver by intercepting the MDIO PHY ID read.
v2:
- Create dedicated PHY driver and use a fake PHY ID that is injected by
the network driver. Suggested by Andrew Lunn.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 171a9bae68 ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):
CONFIG_NETDEVICES=y
CONFIG_STAGING=y
CONFIG_COMPILE_TEST=y
and CONFIG_OCTEON_ETHERNET as either a module or built-in.
WARNING: unmet direct dependencies detected for MDIO_OCTEON
Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]
In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
| ^~~~~~
CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.
CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac516 ("of/mdio: Add dummy functions in of_mdio.h.").
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocated for the stats array may contain arbitrary data.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc52 ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
NIP [c0227bf0] phy_start+0x74/0xc0
LR [c0227bf0] phy_start+0x74/0xc0
Call Trace:
[df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
[df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
[df547828] [c023cf08] gfar_enet_open+0x364/0x374
[df547898] [c029d870] __dev_open+0xe4/0x140
[df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
[df5478f8] [c029dc28] dev_change_flags+0x20/0x54
[df547918] [c02ae304] do_setlink+0x310/0x818
[df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df547c28] [c02b222c] rtnl_newlink+0x48/0x68
[df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
--- interrupt: c01 at 0xfd4e030
LR = 0xfd4e010
Instruction dump:
813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
---[ end trace d4c095aeaf6ea998 ]---
and
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
<...>
Call Trace:
[df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
[df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
[df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
[df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
[df581858] [c0225608] phylink_stop+0x7c/0xe4
[df581868] [c023c57c] stop_gfar+0x7c/0x94
[df581888] [c023c5b8] gfar_close+0x24/0x94
[df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
[df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
[df5818f8] [c029dc28] dev_change_flags+0x20/0x54
[df581918] [c02ae304] do_setlink+0x310/0x818
[df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df581c28] [c02b222c] rtnl_newlink+0x48/0x68
[df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df581f38] [c000d1d8] ret_from_syscall+0x0/0x38
<...>
---[ end trace d4c095aeaf6ea999 ]---
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 2179626156 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The acpi_node_get_property_reference() doesn't return ACPI error codes,
it just returns regular negative kernel error codes. This patch doesn't
affect run time, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ruslan Babayev <ruslan@babayev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This puts the quad PHY ports in power-down mode when the PHY transitions
to the PHY_HALTED state. It is likely that all the other PHYs support
the BMCR_PDOWN bit, but I only have the BCM5464R to test.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP device polling can cause problems during the shutdown process if the
parent devices of the network controller have been shut down already.
This problem was seen on the iMX6 platform with PCIe devices, where
accessing the device after the bus is shut down causes a hang.
Free any acquired GPIO interrupts and stop all delayed work in the SFP
driver during the shutdown process, so that we ensure that no pending
operations are still occurring after the SFP shutdown completes.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]
Commit 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).
The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.
Rename PHY driver to ax88796b.c in order to resolve name conflict.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reducing the support mask as a result of the interface type
selected for SFP modules, or when setting the link settings through
ethtool - this should only change when the supported link modes of
the hardware combination change.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP modules do not like reads longer than 16 bytes, so read the
EEPROM in chunks of 16 bytes at a time. This behaviour is not specified
in the SFP MSAs, which specifies:
"The serial interface uses the 2-wire serial CMOS E2PROM protocol
defined for the ATMEL AT24C01A/02/04 family of components."
and
"As long as the SFP+ receives an acknowledge, it shall serially clock
out sequential data words. The sequence is terminated when the host
responds with a NACK and a STOP instead of an acknowledge."
We must avoid breaking a read across a 16-bit quantity in the diagnostic
page, thankfully all 16-bit quantities in that page are naturally
aligned.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp-bus code now no longer has any use for the network device
structure, so remove its use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add attach and detach methods for SFP buses, which will allow us to get
rid of the netdev storage in sfp-bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using GPIO interrupts with a fixed-link GPIO rather than
polling the GPIO every second and invoking the phylink resolution. This
avoids unnecessary calls to mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev used in the phylink ioctl emulation is never used, so let's
remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
We face the issue that link change interrupt and link status may be
reported by different PHY layers. As a result the link change
interrupt may occur before the link status changes.
Export phy_queue_state_machine to allow PHY drivers to specify a
delay between link status change interrupt and link status check.
v2:
- change jiffies parameter type to unsigned long
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylib interrupt handler handles link change events only currently.
However PHY drivers may want to use other interrupt sources too,
e.g. to report temperature monitoring events. Therefore add a callback
to struct phy_driver allowing PHY drivers to implement a custom
interrupt handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest addition to the PHYLINK infrastructure, we are faced
with a decision on when to print necessary info using the struct
net_device and when with the struct device.
Add a series of macros that encapsulate this decision and replace all
uses of netdev_err&co with phylink_err.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PHYLINK_DEV operation type, the PHYLINK infrastructure can work
without an attached net_device. For printing usecases, instead, a struct
device * should be passed to PHYLINK using the phylink_config structure.
Also, netif_carrier_* calls ar guarded by the presence of a valid
net_device. When using the PHYLINK_DEV operation type, we cannot check
link status using the netif_carrier_ok() API so instead, keep an
internal state of the MAC and call mac_link_{down,up} only when the link
changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that reduces the clutter in phylink_resolve
around calling the .mac_link_up/.mac_link_down driver callbacks. In a
further patch this logic will be extended to emit notifications in case
a net device does not exist.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.
Changes are needed in the following areas:
- Printing: In some places netdev_err was replaced with phydev_err.
- Incrementing reference count to the parent MDIO bus driver: If there
is no net device, then the reference count should definitely be
incremented since there is no chance that it was an Ethernet driver
who registered the MDIO bus.
- Sysfs links are not created in case there is no attached_dev.
- No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.
This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_INTERFACE_MODE_RGMII_RXID is less then TXID
so code to set tx delay is never called.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phy state machine calls _config_init just after
reset.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After reset SGMII Autoneg timer is set to 2us (bits 6 and 5 are 01).
That is not enough to finalize autonegatiation on some devices.
Increase this timer duration to maximum supported 16ms.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For supporting 10Mps speed in SGMII mode DP83867_10M_SGMII_RATE_ADAPT bit
of DP83867_10M_SGMII_CFG register has to be cleared by software.
That does not affect speeds 100 and 1000 so can be done on init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers don't have to and shouldn't fiddle with phylib internals.
Most of the code in bcm87xx_config_init() can be removed because
phylib takes care.
In addition I replaced usage of PHY_10GBIT_FEC_FEATURES with an
implementation of the get_features callback. PHY_10GBIT_FEC_FEATURES
is used by this driver only and it's questionable whether there
will be any other PHY supporting this mode only. Having said that
in one of the next kernel versions we may decide to remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we didn't support mode USXGMII, and in order to not break few
boards mode XGMII was accepted for the AQR107 family even though it
doesn't support XGMII. Add USXGMII support to the Aquantia PHY driver
and warn if XGMII mode is set.
v2:
- add warning if XGMII mode is set
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LXT PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic
genphy_{suspend,resume} functions added by
commit 0f0ca340e5 ("phy: power management support").
LXT970 is left aside because all registers get cleared upon
"power down" exit.
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was being done in config the first time the phy was configured.
Should be in the probe method.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insure property is in valid range and fail when reading DT if it is not.
Also add error message for existing failure if required property is not
present.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver would only set the IO impedance value when RGMII internal
delays were enabled. There is no reason for this. Move the IO
impedance block out of the RGMII delay block.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables used to store u32 DT properties were signed ints. This
doesn't work properly if the value of the property were to overflow.
Use unsigned variables so this doesn't happen.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was assuming the reset default of the delay control register
was to have delay disabled. This is what the datasheet shows as the
register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
If the interface mode is selected as RX or TX delay only, insure the
other direction's delay is disabled.
If the interface mode is just "rgmii", with neither TX or RX internal
delay, one might expect that the driver should disable both delays. But
this is not what the driver does. It leaves the setting at the PHY's
strapping's default. And that default, for no pins with strapping
resistors, is to have delay enabled and 2.00 ns.
Rather than change this behavior, I've kept it the same and documented
it. No delay will most likely not work and will break ethernet on any
board using "rgmii" mode. If the board is strapped to have a delay and
is configured to use "rgmii" mode a warning is generated that "rgmii-id"
should have been used.
Also validate the delay values and fail if they are not in range.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Do not update the link interface mode while the link is down to avoid
spurious link interface changes.
Always call mac_config if we have a PHY to propagate the pause mode
settings to the MAC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XGMII interface mode no longer works on AQR107 after the recent changes,
adding back support.
Fixes: 570c8a7d53 ("net: phy: aquantia: check for supported interface modes in config_init")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy id chosen by Amlogic is incorrectly set in the mdio mux and
does not match the phy driver.
It was not detected before because DT forces the use the correct driver
for the internal PHY.
Fixes: 7090425104 ("net: phy: add amlogic g12a mdio mux support")
Reported-by: Qi Duan <qi.duan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling phy_select_page() and until calling phy_restore_page(),
the mutex 'mdio_lock' is already locked, so the driver should use
non-locked version of phy functions. Or there will be a deadlock with
'mdio_lock'.
This replaces phy functions called from rtl8211e_config_init() to avoid
the deadlock issue.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding missing callbacks I missed that one had them set already.
Interesting that the compiler didn't complain.
Fixes: daf3ddbe11 ("net: phy: realtek: add missing page operations")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing page operation callbacks to few Realtek drivers.
This also fixes a NPE after the referenced commit added code to the
RTL8211E driver that uses phy_select_page().
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's prone to problems if delay is cleared out for other than RGMII
modes. So lets set/clear the TX-delay in the config register only
if actually RGMII-like interface mode is requested. This only
concerns rtl8211f chips.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. Alas this is the only
documented info regarding the RGMII timing control configurations the PHY
provides. It turns out the same settings can be setup via MDIO registers
hidden in the extension pages layout. Particularly the extension page 0xa4
provides a register 0x1c, which bits 1 and 2 control the described delays.
They are used to implement the "rgmii-{id,rxid,txid}" phy-mode.
The hidden RGMII configs register utilization was found in the rtl8211e
U-boot driver:
https://elixir.bootlin.com/u-boot/v2019.01/source/drivers/net/phy/realtek.c#L99
There is also a freebsd-folks discussion regarding this register:
https://reviews.freebsd.org/D13591
It confirms that the register bits field must control the so called
configuration pins described in the table 12-13 of the official PHY
datasheet:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we report symmetric pause only, and we don't consider the local
pause capabilities. Let's properly consider local and remote
capabilities, and report also asymmetric pause.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet). This patch makes sure this factory test
bit is cleared in config_init().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for PHY reset pins handled by a reset controller.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_sanitize_settings() is called from phy_start_aneg() only, and only
if phydev->autoneg isn't set. Therefore the removed code does nothing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new PHY modes are added people may miss to update all relevant places
in the kernel. Therefore add a build bug check for new modes in enum
ethtool_link_mode_bit_indices that haven't been added to phylib yet.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently new modes have been added to ethtool.h, but the related
extension to phylib hasn't been done yet. So add support for these
modes.
v2:
- add missing 100Gbps and 50Gbps modes
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of array settings[] is quite lengthy meanwhile. Add a
macro to shrink the definition.
v2:
- Fix an indentation issue
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_c45_aneg_done() is used by phylib as fallback for c45 PHY's if
callback aneg_done isn't defined. So we don't have to set this
explicitly. Same for genphy_c45_pma_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this change is to align the gxl and g12a driver
declaration.
Like on the g12a variant, remove genphy_aneg_done() from the driver
declaration as the net phy framework will default to it anyway.
Also, the gxl phy id should be an exact match as well, so let's change
this and use the macro provided.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The g12a SoC family uses the type of internal PHY that was used on the
gxl family. The quirks of gxl family, like the LPA register corruption,
appear to have been resolved on this new SoC generation.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the mdio mux and internal phy glue of the g12a SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # clk parts
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phylib uses genphy_read_abilities() as fallback, we don't have
to set callback get_features any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meanwhile we have generic functions for reading the abilities of
Clause 22 / 45 PHY's. This allows to use them as fallback in case
callback get_features isn't set. Benefit is the reduction of
boilerplate code in PHY drivers.
v2:
- adjust the comment in phy_driver_register to match the code
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c ("net: phy: improve genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 88x2110 PHY support was added, the suspend and resume callbacks
were forgotten. This patch adds them to the 88x2110 PHY callback
definition.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the suspend/resume callbacks for Marvell 10G PHYs. The
three PCS (base-t, base-r and 1000base-x) are set in low power (the PCS
are powered down) when the PHY isn't used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mii_lpa_mod_linkmode_lpa_t() checks bit LPA_LPACK to detect
whether link partner supports autoneg. This doesn't work correctly at
least on Aquantia AQCS109 when it negotiates 1000Base-T2 mode.
The "link partner is autoneg-capable" bit as defined by clause 45 is
set however. Better let's switch in general to use the clause 45
standard for link partner autoneg detection.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_read_abilities(). This allows to remove all
calls to genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQR107 family has SGMII statistics counters. Let's expose them to
ethtool. To interpret the counters correctly one has to be aware that
rx on SGMII side is tx on ethernet side. The counters are populated
by the chip in 100Mbps/1Gbps mode only.
v2:
- add constant AQR107_SGMII_STAT_SZ
- add struct aqr107_priv to be prepared for more private data fields
- let aqr107_get_stat() return U64_MAX in case of an error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves few aspects of genphy_read_status():
- Don't initialize lpagb, it's not needed.
- Move initializing phydev->speed et al before the if clause.
- In auto-neg case, skip populating lp_advertising if we
don't have a link. This avoids quite some unnecessary
MDIO reads in case of phylib polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend / resume callbacks for AQR107 family. Suspend powers down
the complete chip except MDIO and internal CPU.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for zero timeout is always true at the end of the proceeding
while loop; the only other exit path in the loop is if the unimac MDIO
is not busy. Remove the redundant zero timeout check and always
return -ETIMEDOUT on this timeout return path.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1000BaseT standard requires that a link is reported as down earliest
after 750ms. Several use case however require a much faster detecion
of a broken link. Fast Link Down supports this by intentionally
violating a the standard. This patch exposes the Fast Link Down
feature of 88E1540 and 88E6390. These PHY's can be found as internal
PHY's in several switches: 88E6352, 88E6240, 88E6176, 88E6172,
and 88E6390(X). Fast Link Down and EEE are mutually exclusive.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQCS109 supports a proprietary 2-pair 1Gbps mode. The standard
registers don't allow to tell between 1000BaseT and 1000BaseT2.
Add reporting this proprietary mode based on a vendor register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting firmware details. These details are available only once
the firmware has finished initializing the chip. This can take some
time and we need to poll for init completion.
v2:
- Propagate timeout in aqr107_wait_reset_complete(). Don't bail out
completely on timeout because chip may be functional even w/o
firmware image.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If both link partners are Aquantia PHY's then additional information is
exchanged as part of the auto-negotiation. Report remote capabilities
if link partner is Aquantia PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 90eff9096c ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tristate prompt should have been replaced rather than defined a few
lines below, rebase mistake.
Fixes: 17cc982176 ("net: phy: Move Omega PHY entry to Cygnus PHY driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.
v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus and Omega are part of the same business unit and product line, it
makes sense to group PHY entries by products such that a platform can
select only the drivers that it needs. Bring all the functionality that
the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY
entry from bcm7xxx.c.
As an added bonus, we now have a proper mdio_device_id entry to permit
auto-loading.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the auto-negotiated speed the PHY may change the interface
mode. Check for new mode and set phydev->interface accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: picked from bigger patch and reworked]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let config_init check for unsupported interface modes on AQR107/AQCS109.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: adjusted for AQR107/AQCS109 specifics]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.
This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.
Changes are compile-tested only.
A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.
[0] https://marc.info/?t=153782508800006&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20a ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:
WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
Selected by [m]:
- MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]
Fixes: 7865ad6551 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.
Fixes: 9a5dc8af44 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen10g_read_status is deprecated, therefore stop exporting it.
We don't want to encourage anybody to use it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported
and advertising bitmap because it's part of PHY_10GBIT_FEATURES.
And all users of gen10g_config_init use PHY_10GBIT_FEATURES.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend() and phy_resume() are no-ops anyway if no callback is
defined. Therefore we don't need these stubs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.
We therefore don't need to manually do that in mv3310_get_features().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Generic Mux controls, when Mdio mux node is a consumer
of mux produced by some other device.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
(avoids problems if PHY driver is built in and HWMON is a module)
v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR,
add this. Users will ignore speed and duplex settings in BMCR because
we're emulating auto-neg, therefore we can remove related code.
See also following discussion [0].
[0] https://marc.info/?t=155041784900002&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates
whether or not we should read register (1.21) "2.52/5G PMA Extended
Abilities", which contains information on the support of 2.5GBASET and
5GBASET.
After testing on several variants of PHYS of this family, it appears
that bit 14 in (1.11) isn't always set when it should be.
PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET,
but don't have 1.11.14 set. Their register 1.21 is filled with the
correct values, indicating 2.5G and 5G support.
PHYs 88E2110 do have their 1.11.14 bit set, as it should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.
Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.
At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.
This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch making use of helpers dedicated to linkmodes handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Alaska family of 10G PHYs has more abilities than the ones listed in
PHY_10GBIT_FULL_FEATURES, the exact list depending on the model.
Make use of the newly introduced .get_features call to build this list,
using genphy_c45_pma_read_abilities to build the list of supported
linkmodes, and adding autoneg ability based on what's reported by the AN
MMD.
.config_init is still used to validate the interface_mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.
There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.
For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.
Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_read_status(). 1000BaseT link partner
advertisement needs to be read from vendor registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new PHY driver call to get the PHYs supported features.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: removed new config_init callback from patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mii_10gbt_stat_mod_linkmode_lpa_t() in genphy_c45_read_lpa() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
fix this by using IS_ERR before PTR_ERR
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY core expects PHY drivers not to set Pause and Asym_Pause bits,
unless the driver only wants to specify one of them due to HW
limitation. In the case of the Marvell10g driver, we don't need to set
them.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have phy_resolve_aneg_linkmode() we can make
genphy_read_status() much simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the advertisement registers content didn't change, we may have
just switched to aneg, and therefore have to trigger an aneg restart.
This matches the behavior of genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_config_aneg() in mv3310_config_aneg().
v2:
- add a comment regarding 1000BaseT vendor registers
v3:
- rebased
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: patch splitted]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.
v2:
- change function name to genphy_c45_an_config_aneg
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use new helper linkmode_adv_to_mii_10gbt_adv_t and split patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3bz specification, based on previous by the NBASET alliance,
defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on
cat5e, cat6 and cat7 cables.
These mode integrate with the already defined C45 MDIO PMA/PMD registers
set that added 10G support, by defining some previously reserved bits,
and adding a new register (2.5G/5G Extended abilities).
This commit adds the required definitions in include/uapi/linux/mdio.h
to support these modes, and detect when a link-partner advertises them.
It also adds support for these mode in the generic C45 PHY
infrastructure.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function phy_modify_mmd_changed(), the result speaks for itself.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5 ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide phylink_init_eee() to allow MAC drivers to initialise PHY EEE
from within the ethtool set_eee() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's little point calling mac_config() when the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_modify_changed() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing mv3310_modify() with phy_modify_mmd() we missed that
they behave differently, mv3310_modify() returns 1 on a changed
register value whilst phy_modify_mmd() returns 0. Fix this by replacing
phy_modify_mmd() with phy_modify_mmd_changed() where needed.
Fixes: b52c018ddc ("net: phy: make use of new MMD accessors")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When modifying registers there are scenarios where we need to know
whether the register content actually changed. This patch adds
new helpers to not break users of the current ones, phy_modify() etc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the AQCS109. From software point of view,
it should be almost equivalent to AQR107.
v2:
- make Nikita the author
- document what I changed
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use PHY_ID_MATCH_MODEL mascro]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for runtime determination of what the PHY supports, by
adding a new function to the phy driver. The get_features call should
set the phydev->supported member with the features the PHY supports.
It is only called if phydrv->features is NULL.
This requires minor changes to pause. The PHY driver should not set
pause abilities, except for when it has odd cause capabilities, e.g.
pause cannot be disabled. With this change, phydev->supported already
contains the drivers abilities, including pause. So rather than
considering phydrv->features, look at the phydev->supported, and
enable pause if neither of the pause bits are already set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: fixed small checkpatch complaint in one comment]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon support asking the PHY at runtime to determine what
features it supports, rather than forcing it to be compile time.
But we should probe the PHY first. So probe the phy driver earlier.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY registers are only 16 bits wide, therefore, if the read was
successful, there's no need to mask out the higher 16 bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 0 in register 1.5 doesn't represent a device but is a flag that
Clause 22 registers are present. Therefore disregard this bit when
populating the device list. If code needs this information it
should read register 1.5 directly instead of accessing the device
list.
Because this bit doesn't represent a device don't define a
MDIO_MMD_XYZ constant, just define a MDIO_DEVS_XYZ constant for
the flag in the device list bitmap.
v2:
- make masking of bit 0 more explicit
- improve commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status register latches link-down events. Therefore, if link
is reported as being up, there's no need for a second read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.
On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
Interrupt handler reads link status, means it reads the latched
"link is down" info. But there won't be another interrupt as long
as link stays up, therefore phylib will never recognize that link
is up.
Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fixed_phy_register_with_gpiod() API. It lets users create a
fixed_phy instance that uses a GPIO descriptor which was obtained
externally e.g. through platform data.
This enables platform devices (non-DT based) to use GPIOs for link
status.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix fixed_phy not checking GPIO if no link_update callback
is registered.
In the original version all users registered a link_update
callback so the issue was masked.
Fixes: a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full set of locked and unlocked accessor functions to read and
write PHY MMD registers and/or bitfields.
Set of functions exactly matches what is already available for PHY
legacy registers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic numbers with proper constants. The original patch is
from Andrew, I extended / adjusted certain parts:
- Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F.
- Order defines from highest to lowest bit numbers
- correct some typos
- add constant MDIO_AN_TX_VEND_INT_MASK2_LINK
- Remove few functional improvements from the patch, they will come as
a separate patch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of macro PHY_ID_MATCH_MODEL to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded header includes.
v2:
- leave kernel.h in
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aquantia_ as a name space prefix is rather long, resulting in lots of
lines needing wrapping, reducing readability. Use the prefix aqr_
instead, which fits with the vendor naming there devices aqr107, for
example.
v2:
- add SoB from Heiner
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6623c0fba1.
The original diagnosis was incorrect: it appears that the NIC had
PHY polling mode enabled, which meant that it overwrote the PHYs
advertisement register during negotiation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libphy provides a standard set of helpers to access the MMD PHY
registers. Use those instead of relying on custom driver-specific
functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts don't have to be enabled before calling phy_start().
Therefore let's enable them in phy_start(). In a subsequent step
we'll remove enabling interrupts from phy_connect_direct().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_start() should be called from states PHY_READY or PHY_HALTED only.
Check for this to detect misbehaving drivers. Also the state machine
should be started only when being called from one of the valid states.
Some more background:
For all invalid states phy_start() basically was a no-op. All it did
was triggering a state machine run, but for all "running" states the
poll loop was active anyway. And if called from PHY_DOWN, the state
machine does nothing.
v3:
- extended commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY and MDIO drivers refer to the COPYING file in the main
directory of this archive. This is the main license for Linux, thus
GPLv2 plus syscall extension.
Fixup the MODULE_LICENSE() where needed and add an SDPX header for
GPLv2.
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2 license text. They then either have
a MODULE_LICENSE() of GPLv2+, or an SPDX tag of GPLv2+.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup with others when there are contradictions.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2+ license text. They then either have
a MODULE_LICENSE() of GPLv2 only, or an SPDX tag of GPLv2 only.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup the others when there are contradictions.
Cc: David Wu <david.wu@rock-chips.com>
Cc: Dongpo Li <lidongpo@hisilicon.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPDX header makes any license text redundent. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RGMII mode, phy delay should be disabled. Add this case along
with disable delay routines.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the soft reset (if defined) is done only if the driver also
implements the config_init callback. I think this dependency is a
mistake, so let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that on a system with nfsboot and w/o initramfs network
fails because trying to load the PHY driver returns -ENOENT. Reason was
that due to missing initramfs the modprobe binary isn't available.
So we have to ignore error code -ENOENT.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to the phylib state machine in phy_stop() just ensures that
the state machine isn't re-triggered, but a state machine call may
be scheduled already. So lets's call phy_stop_machine().
This also allows to get rid of the call to phy_stop_machine() in
phy_disconnect().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop PHY if needed when entering phy_disconnect. This allows drivers
that don't need a separate call to phy_stop() to omit this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only caller of get_phy_id() is get_phy_device(). There a PHY ID of
0xffffffff is translated back to -ENODEV. So we can avoid some
overhead by returning -ENODEV directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent changes to the phylib state machine state PHY_CHANGELINK
isn't used any longer. Therefore let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver implements open-coded versions of phy_read_mmd() and
phy_write_mmd() for KSZ9031. That's not needed, let's use the
phylib functions directly.
This is compile-tested only because I have no such hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting the PHY driver module fails we'll bind the genphy
driver later. This isn't obvious to the user and may cause, depending
on the PHY, different types of issues. Therefore check the return code
of request_module(). Note that we only check for failures in loading
the module, not whether a module exists for the respective PHY ID.
v2:
- add comment explaining what is checked and what is not
- return error from phy_device_create() if loading module fails
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are already checking in phy_detach() that the PHY driver is of
generic kind (1G or 10G) and we are going to make use of that in the SFP
layer as well for 1000BaseT SFP modules, so expose helper functions to
return that information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to and one shouldn't include asm/irq.h directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago phydev_info() and friends have been added. They allow to
improve and simplify logging.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround attempt helped for some but not all affected users.
With commit 11287b693d ("r8169: load Realtek PHY driver module
before r8169") we have a better workaround now, so we an remove
the first attempt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().
Fixes: 424ca4c551 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.
Fixes: e4cf8a38fc ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding checks to detect wrong usage of the phylib API we added
a check to phy_start_aneg() which is too strict. If the phylib
state machine is in state PHY_HALTED we should allow reconfiguring
and restarting aneg, and just don't touch the state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6390 Ethernet switch family does not perform MDIO
turnaround correctly. Many hardware MDIO bus masters don't care about
this, but the bitbangging implementation in Linux does by default. Add
phy_ignore_ta_mask to the platform data so that the bitbangging code
can be told which devices are known to get TA wrong.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is sometimes necessary to instantiate a bit-banging MDIO bus as a
platform device, without the aid of device tree.
When device tree is being used, the bus is not scanned for devices,
only those devices which are in device tree are probed. Without device
tree, by default, all addresses on the bus are scanned. This may then
find a device which is not a PHY, e.g. a switch. And the switch may
have registers containing values which look like a PHY. So during the
scan, a PHY device is wrongly created.
After the bus has been registered, a search is made for
mdio_board_info structures which indicates devices on the bus, and the
driver which should be used for them. This is typically used to
instantiate Ethernet switches from platform drivers. However, if the
scanning of the bus has created a PHY device at the same location as
indicated into the board info for a switch, the switch device is not
created, since the address is already busy.
This can be avoided by setting the phy_mask of the mdio bus. This mask
prevents addresses on the bus being scanned.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MII_ADVERTISE register is modified by the IOCTL handler,
phydev->advertising needs recalculating. Use the _mod_ variant of
mii_adv_to_linkmode_adv_t so that bits outside of the advertise
registers are not cleared.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_lpa_to_linkmode_lpa_t to mii_lpa_mod_linkmode_lpa_t to
indicate it modifies the passed linkmode bitmap, without clearing any
other bits.
Also, ensure bit are clear which the lpa indicates should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
ef1b5bf506 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b812 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the icplus driver has been fixed all PHY drivers supporting
interrupts have both callbacks (config_intr and ack_interrupt)
implemented - as it should be. Therefore phy_drv_supports_irq()
can be changed now to check for both callbacks being implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:
1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
config_intr callback. Now we can add a phylib plausibility check
disabling interrupt mode if one of the two irq-related callbacks
isn't defined.
I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change modified variable advertising from a u32 to a link mode
array and left the u32 zero comparison, so essential we now have an array
being compared to null which is not the intention. Fix this by using the
call to linkmode_empty to check if advertising is all zero.
Detected by CoverityScan, CID#1475424 ("Array compared against 0")
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/phy/marvell.c: In function 'm88e1510_config_init':
drivers/net/phy/marvell.c:850:7: warning:
variable 'pause' set but not used [-Wunused-but-set-variable]
It not used any more after commit 3c1bcc8614 ("net: ethernet: Convert phydev
advertize and supported from u32 to link mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_check_link_status in more places in the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few places in the state machine the state is set to PHY_RUNNING or
PHY_NOLINK after doing a phy_read_status(). So factor this out to
phy_check_link_status().
First use it in phy_start_aneg(): By setting the state to PHY_RUNNING
or PHY_NOLINK directly we can remove the code to handle the case that
we're using interrupts and aneg was finished already.
Definition of phy_link_up and phy_link_down needs to be moved because
they are called in the new function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg isn't finished yet then the PHY reports the link as down.
There's no benefit in setting the state to PHY_AN because the next
state machine run would set the status to PHY_NOLINK anyway (except
in the meantime aneg has been finished and link is up). Therefore
we can set the state to PHY_RUNNING or PHY_NOLINK directly.
In addition change the do_carrier parameter in phy_link_down() to true.
If carrier was marked as up before (what should never be the case because
PHY was in state PHY_HALTED before) then we should mark it as down now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If aneg is enabled and the PHY reports the link as up then definitely
aneg finished successfully. Therefore this check is useless and
can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandru Ardelean