Ingenic SoC declares ZBOOT support, but debug definitions are missing
for MACH_JZ4780 resulting in a build failure when DEBUG_ZBOOT is set.
The UART addresses are same as with JZ4740, so fix by covering JZ4780
with those as well.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 29bb45f25f (regmap-mmio: Use native endianness for read/write)
attempted to fix some long standing bugs in the MMIO implementation for
big endian systems caused by duplicate byte swapping in both regmap and
readl()/writel() which affected MIPS systems as when they are in big
endian mode they flip the endianness of all registers in the system, not
just the CPU. MIPS systems had worked around this by declaring regmap
using IPs as little endian which is inaccurate, unfortunately the issue
had not been reported.
Sadly the fix makes things worse rather than better. By changing the
behaviour to match the documentation it caused behaviour changes for
other IPs which broke them and by using the __raw I/O accessors to avoid
the endianness swapping in readl()/writel() it removed some memory
ordering guarantees and could potentially generate unvirtualisable
instructions on some architectures.
Unfortunately sorting out all this mess in any half way sensible fashion
was far too invasive to go in during an -rc cycle so instead let's go
back to the old broken behaviour for v4.5, the better fixes are already
queued for v4.6. This does mean that we keep the broken MIPS DTs for
another release but that seems the least bad way of handling the
situation.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
On many MIPS systems the endianness of IP blocks is kept the same as
that of the CPU by the hardware. This includes the system controllers
on these systems which are controlled via syscon which uses the regmap
API which used readl() and writel() to interact with the hardware,
meaning that all writes are converted to little endian when writing to
the hardware. This caused a bad interaction with the regmap core in big
endian mode since it was not aware of the byte swapping and so ended up
performing little endian writes.
Unfortunately when this issue was noticed it was addressed by updating
the DT for the affected devices to specify them as little endian. This
happened to work since it resulted in two endianness swaps which
cancelled each other out and gave little endian behaviour but meant that
the DT was clearly not accurately describing the hardware.
The intention of commit 29bb45f25f (regmap-mmio: Use native
endianness for read/write) was to fix this by making regmap default to
native endianness but this breaks most other MMIO users where the
hardware has a fixed endianness and the implementation uses the __raw
accessors which are not intended to be used outside of architecture
code. Instead use the newly added native-endian DT property to say
exactly what we want for these systems.
Fixes: 29bb45f25f (regmap-mmio: Use native endianness for read/write)
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds basic DTS configuration for the PIC32MZDA chip and in turn the
PIC32MZDA Starter Kit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.
Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.
[ralf@linux-mips.org: fold in Geert Uytterhoeven's patch and acks from
Harvey's latest version.]
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mtd@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/11695/
Patchwork: https://patchwork.linux-mips.org/patch/11914/
Patchwork: https://patchwork.linux-mips.org/patch/11985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is 2 registers that is 8 bytes long, not 4.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alexander Couzens <lynxis@fe80.eu>
Cc: Joel Porquet <joel@porquet.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11508/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The regmap API has an endianness setting for formatting reads and writes.
This can be set by the usual DT "little-endian" and "big-endian" properties.
To work properly the associated regmap_bus needs to read/write in native
endian.
The "syscon" DT device binding creates an mmio-based regmap_bus which
performs all reads/writes as little-endian. These values are then converted
again by regmap, which means that all of the MIPS BCM boards (which are
big-endian) have been declared as "little-endian" to get regmap to convert
them back to big-endian.
Modify regmap-mmio to use the native-endian functions __raw_read*() and
__raw_write*() instead of the little-endian functions read*() and
write*().
Modify the big-endian MIPS BCM boards to use what will now be the correct
endianness instead of pretending that the devices are little-endian.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Move memory configuration to be performed via device tree for the Malta
board. This moves more Malta specific code to malta-dtshim.c, leaving
the rest of the mti-malta code a little more board-agnostic. This will
be useful to share more code between boards, with the device tree
providing the board specifics as intended.
Since we can't rely upon Malta boards running a bootloader capable of
handling devictrees & filling in the required information, a piece of
shim code (malta_dt_shim) is added to consume the (e)memsize variables
provided as part of the bootloader environment (or on the kernel command
line) then generate the DT memory node using the provided values.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Patchwork: https://patchwork.linux-mips.org/patch/11222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
When loading x86 64bit kernel above 4GiB with patched grub2, got kernel
gunzip error.
| early console in decompress_kernel
| decompress_kernel:
| input: [0x807f2143b4-0x807ff61aee]
| output: [0x807cc00000-0x807f3ea29b] 0x027ea29c: output_len
| boot via startup_64
| KASLR using RDTSC...
| new output: [0x46fe000000-0x470138cfff] 0x0338d000: output_run_size
| decompress: [0x46fe000000-0x47007ea29b] <=== [0x807f2143b4-0x807ff61aee]
|
| Decompressing Linux... gz...
|
| uncompression error
|
| -- System halted
the new buffer is at 0x46fe000000ULL, decompressor_gzip is using
0xffffffb901ffffff as out_len. gunzip in lib/zlib_inflate/inflate.c cap
that len to 0x01ffffff and decompress fails later.
We could hit this problem with crashkernel booting that uses kexec loading
kernel above 4GiB.
We have decompress_* support:
1. inbuf[]/outbuf[] for kernel preboot.
2. inbuf[]/flush() for initramfs
3. fill()/flush() for initrd.
This bug only affect kernel preboot path that use outbuf[].
Add __decompress and take real out_buf_len for gunzip instead of guessing
wrong buf size.
Fixes: 1431574a1c (lib/decompressors: fix "no limit" output buffer length)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
The "LD vmlinuz" line in the quiet build output is misaligned with the
rest of the output. Fix this.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build a DT for the Malta platform into the kernel, load it & probe
devices from it. The DT is essentially empty at this point, devices
will be added in further patches.
[ralf@linux-mips.org: Fixed conflicts.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/10119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build all available dtbs to allow them to be appended to the resulting
kernel in case there is no builtin dtb.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hartley <James.Hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9740/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for detecting a vmlinuz.bin appended dtb and overriding
the boot arguments to match the UHI interface.
To ensure _edata / __apendend_dtb points to the actual end of the
binary, align the data section to 16 bytes instead of the address
cursor.
Due to ld.script not going through the preprocessor, we can't check
for MIPS_ZBOOT_APPENDED_DTB being enabled, so always reserve space
for it. It should have no consequences for booting without it enabled
except 1 MiB more ram usage during the uncompressing stage.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hartley <James.Hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9741/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a DTS for TL-WR1043ND version 1 and allow to have it built in the
kernel to circumvent the broken u-boot found on these boards.
Currently only the UART, LEDs and buttons are supported.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add two uart device nodes known as the uart1 and uart2 for the bcm7xxx
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a DTS file and Kconfig entry for the BCM97435SVMB evaluation board
using bcm7435.dtsi as an example.
The current code needs some tweaking to allow us to use the
dual-threaded dual BMIPS5200 CPUs, so for now we limit ourselves to
allowing just a single CPU to be booted.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: cernekee@chromium.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/9972/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support the Ingenic JZ4780 SoC using the existing code under
arch/mips/jz4740 now that it has been generalised sufficiently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/10164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the serial support from arch/mips/jz4740 & make use of the new
Ingenic SoC UART driver. This is done for both regular & early console
output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: Alexandre Courbot <gnurou@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate the JZ4740 & the qi_lb60 board to use common clock framework
via the new Ingenic SoC CGU driver. Note that the JZ4740-specific
debugfs code is removed since common clock framework provides its own
debug capabilities.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Declare the JZ4740 interrupt controller for probe via DT using the
standard irqchip_init function, and make use of that function to probe
the controller by adding the appropriate node to the JZ4740 dtsi.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the generic irqchip_init function to probe irqchip drivers using DT,
and add the appropriate node to the JZ4740 devicetree in place of the
call to mips_cpu_irq_init.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Patchwork: https://patchwork.linux-mips.org/patch/10166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Require a DT for JZ4740 based systems, and add a stub one for the
qi_lb60 (Ben NanoNote) board. Devices will be migrated to being probed
via this DT over time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
!CONFIG_DEBUG_ZBOOT doesn't need puts() and puthex(), remove them and
the corrospindig strings for !CONFIG_DEBUG_ZBOOT, as a result, it saves
about 1280 bytes.
[ralf@linux-mips.org: Resolved reject.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1898/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DSR-1000N board has two GPIO LEDs next to USB ports. Add support for them.
[ralf@linux-mips.org: Resolved conflict due to the moving of the DTS files
into vendor subdirectories.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9624/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms which use raw zboot images may need to link the image at
a fixed address if there is no other way to communicate the load
address to the bootloader. Allow the per-platform Kbuild files
to specify an optional zboot image load address (zload-y) and fall
back to calc_vmlinuz_load_addr if unset.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9566/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
Allow more compression algorithms as well as uncompressed uImage.bin
to be generated. An uncompressed image might be useful to rule out
problems in the decompression code in the bootloader or even speed
up the boot process at the expense of a bigger uImage file.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HOSTCC arch/mips/boot/elf2ecoff
arch/mips/boot/elf2ecoff.c: In function ‘main’:
arch/mips/boot/elf2ecoff.c:271:8: warning: variable ‘shstrtab’ set but not used [-Wunused-but-set-variable]
char *shstrtab;
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These are generated by very recent toolchains and result in an error
message when attenpting to convert a kernel from ELF to ECOFF.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The if construct was getting hard to read and would be getting even more
complex with the next bug fix.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Ralink device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. A built-in device-tree is optional, so select
BUILTIN_DTB when it is requested.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7561/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Netlogic XLP device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. A built-in device-tree is optional, so select
BUILTIN_DTB when it is requested.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7560/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the SEAD-3 device-tree to arch/mips/boot/dts/ and update the
Makefiles accordingly. Since SEAD-3 requires the device-tree to be
built into the kernel, select BUILTIN_DTB when building for SEAD-3.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7555/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Lantiq device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. There is currently only a single Lantiq
device-tree (EASY50712), and it's required to be built into the kernel,
so select BUILTIN_DTB for it.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7559/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Octeon device-trees to arch/mips/boot/dts/ and update the
Makefiles accordingly. Since Octeon requires the device-tree to be
built into the kernel, select BUILTIN_DTB as well.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7556/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a 'dtbs' Makefile target that just builds the device-tree binaries
enabled by the configuration.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7557/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for moving the device-trees to a common location,
introduce the config option BUILTIN_DTB, which can be selected by
platforms that use a device-tree built into the kernel image, and
create a Makefile to build the device-trees in arch/mips/boot/dts/.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7564/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit dc4d7b37 (MIPS: ZBOOT: gather string functions into string.c)
moved the string related functions into a separate file, which might
cause the following build error, depending on the configuration:
| CC arch/mips/boot/compressed/decompress.o
| In file included from linux/arch/mips/boot/compressed/../../../../lib/decompress_unxz.c:234:0,
| from linux/arch/mips/boot/compressed/decompress.c:67:
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'fill_temp':
| linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_stream.c:162:2: error: implicit declaration of function 'memcpy' [-Werror=implicit-function-declaration]
| cc1: some warnings being treated as errors
| linux/scripts/Makefile.build:308: recipe for target 'arch/mips/boot/compressed/decompress.o' failed
| make[6]: *** [arch/mips/boot/compressed/decompress.o] Error 1
| linux/arch/mips/Makefile:308: recipe for target 'vmlinuz' failed
It does not fail with the standard configuration, as when
CONFIG_DYNAMIC_DEBUG is not enabled <linux/string.h> gets included in
include/linux/dynamic_debug.h. There might be other ways for it to
get indirectly included.
We can't add the include directly in xz_dec_stream.c as some
architectures might want to use a different version for the boot/
directory (see for example arch/x86/boot/string.h).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch implements the stack protector code in MIPS compressed boot
phase based on the same code added to arm in commit
8779657d29 "stackprotector: Introduce
CONFIG_CC_STACKPROTECTOR_STRONG" by Kees Cook <keescook@chromium.org>
Signed-off-by: Ben Chan <benchan@chromium.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
In the worst case this adds less then 128 bytes of code
but on the other hand this makes code organization more clear.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6344/
Add support for the LZ4 compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "lz4" compression tool to compress the vmlinux.bin
payload
- memcpy() is also required for decompress_unlz4.c so we share the
implementation between GZIP, XZ and now LZ4
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5829/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is currently no corresponding ELF program header for the "text"
loadable segment which is confusing for some bootloader out there such
as CFE because it expects to find a program header matching the segment
it is trying to load. The Linux kernel ELF binary "vmlinux" has a
similar program header for the text segment so we just mimic this here
too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5827/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XZ compression scheme in the ZBOOT decompression
stub, in order to support it we need to:
- select the "xzkern" compression tool to compress the vmlinux.bin
payload
- link with ashldi3.o for xz_dec_run() to work
- memcpy() is also required for decompress_unxz.c so we share the
implementation between GZIP and XZ
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5818/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a uImage build target for MIPS, which builds uImage.gz (a U-Boot
image of vmlinux.bin.gz), and then symlinks it to uImage. This allows
for the use of other compression algorithms in future, and is how a few
other architectures do it.
It's enabled conditionally on load-y >= 0xffffffff80000000 which
hopefully allows 64bit kernels to also work as long as the load and
entry address can be represented by the 32bit addresses in the U-Boot
image format.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The vmlinux load address and entry address is calculated in multiple
places:
- arch/mips/Makefile defines load-y from CONFIG_PHYSICAL_START (or
defined by the platform) and passes it to
arch/mips/boot/compressed/Makefile.
- arch/mips/boot/compressed/Makefile calculates kernel entry using nm.
- arch/mips/lasat/image/Makefile calculates both load and entry address
using nm.
Lets combine these in the main Makefile and then pass them as Make
parameters to each of the three boot image Makefiles (in boot/,
boot/compressed, lasat/image/). The boot/ Makefile doesn't currently use
them, but will soon need to for U-Boot image targets.
The existing load-y definition is used in preference to calculating the
load address using nm.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add symlink to include/dt-bindings from arch/mips/boot/dts/include/ to
match the ones in ARM and Meta architectures so that preprocessed device
tree files can include various useful constant definitions.
See commit c58299a (kbuild: create an "include chroot" for DT bindings)
merged in v3.10-rc1 for details.
MIPS structures it's dts files a little differently to other
architectures, having a separate dts directory for each SoC/platform,
but most of the definitions in the dt-bindings/ directory are common so
for now lets just have a single "include chroot" for all MIPS platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Steven. J. Hill <steven.hill@imgtec.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Patchwork: http://patchwork.linux-mips.org/patch/5745/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building with -fstack-protector, gcc emits the __stack_chk_guard and
__stack_chk_fail symbols to check for stack stability. These symbols are
defined in vmlinux but the generated vmlinux.bin that is used to create
the compressed vmlinuz image has no symbol table so the linker can't find
these symbols during the final linking phase. As a result of which, we
need either to redefine these symbols just for the compressed image or drop
the -fstack-protector option when building the compressed image. This patch
implements the latter of two options.
Fixes the following linking problem:
dbg.c:(.text+0x7c): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0x80): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0xd4): undefined reference to `__stack_chk_guard'
dbg.c:(.text+0xec): undefined reference to `__stack_chk_fail'
[ralf@linux-mips.org: I'm applying this before the patch that actually adds
stack protector support for MIPS. This means, it will not be possible
to trigger above error message with any commit from the tree but rather
they are what one would hit without this commit.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add SYS_SUPPORTS_ZBOOT and SYS_SUPPORTS_ZBOOT_UART16550 config options
for XLR and XLP.
Update boot/compressed/uart-16550.c to add UART port for XLR and XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5417/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Combine support for the DB1200/PB1200, DB1300 and DB1550 boards into
a single kernel image.
defconfig-generated image verified on DB1200, DB1300 and DB1550.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4335/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for building a compressed kernel for the JZ4740
architecture.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3563/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
HOSTCC arch/mips/boot/compressed/calc_vmlinuz_load_addr
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c: In function 'main':
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:35:2: warning: format '%llx' expects type 'long long unsigned int *', but argument 3 has type 'uint64_t *'
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:54:2: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
[Ralf: I changed the patch to explicitly list all files to be deleted out
of paranoia.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1590/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix VMLINUZ_LOAD_ADDRESS calculation to be based on the length of
vmlinux.bin, the actual uncompressed kernel binary.
Previously it was based on the length of KBUILD_IMAGE (the unstripped ELF
vmlinux), which is bigger than vmlinux.bin. As a result, vmlinuz was
loaded into a memory address higher then actually needed - a problem for
small memory platforms.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
To: linux-mips@linux-mips.org
Cc: alex@digriz.org.uk
Cc: manuel.lauss@googlemail.com
Cc: sam@ravnborg.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1564/
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have calculated VMLINUZ_LOAD_ADDRESS in shell, which is indecipherable. This
patch rewrites it in C.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips <linux-mips@linux-mips.org>
Cc: Alexander Clouter <alex@digriz.org.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alexander Clouter <alex@digriz.org.uk>
Patchwork: https://patchwork.linux-mips.org/patch/1324/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Remove several outdated comments
- Clearify the definition of zimage_start and zimage_size and the their
usage
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1382/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Remove unused symbols: _fdata, _text; only _edata and _end are needed by
head.S
- Remove unused sections: .sbss, .stab, .gptab.sdata, .gptab.sbss
- Change the alignment to 16 bytes to ensure it is greater than any
fundamental type of a MIPS compiler.
- Clean up comments
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The compressed vmlinux.bin is only a temp file so it's ok to use the same
suffix .z for them (.gz,.lzo,.lzma...) to remove several lines and simpify
the maintenance (no need to add the "suffix_$(xxx) := suffix" line).
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips <linux-mips@linux-mips.org>
Cc: Alexander Clouter <alex@digriz.org.uk>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use hostprogs-y for the elf2ecoff
- list all *.o file in targets
- renamed obj-y to vmlinuzobjs-y (it was confusing to re-use a kbuild variable)
- fix all uses of if_changed/cmd
- use kbuild rules to beautify output
- update clean-file to clean vmlinuz.* in top-level directory
- simplied logic in arch/mips/Makefile for compressed targets
The net result is a more kbuild conformant Makefile but
readability did not increase.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1304/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- remove stuff that is not needed
VMLINUX assignment, all: rule
- use hostprogs-y for the host program
- use kbuild rules for the three targets - to beautify output
- drop clean-files - it is no longer needed
- simplify arch/mips/Makefile when calling targets in boot/Makefile
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips <linux-mips@linux-mips.org>
To: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1303/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a new DEBUG_ZBOOT option to allow the users to enable it
to debug the compressed kernel support for a new board and this optoin
should be disabled to reduce the kernel image size and speed up the
kernel booting procedure when the compressed kernel support is stable.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/918/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hook up the compressed debug output for all Alchemy systems supported
by current kernel codebase.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/879/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
POSIX requires $((<expression>)) arithmetic in sh only to have long
arithmetic so on 32-bit sh binaries might do only 32-bit arithmetic but
the arithmetic done in arch/mips/boot/compressed/Makefile needs 64-bit.
I play with the AR7 platform, so VMLINUX_LOAD_ADDRESS is
0xffffffff94100000, and for an example 4MiB kernel
VMLINUZ_LOAD_ADDRESS is made out to be:
----
alex@berk:~$ bash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
ffffffff94500000
alex@berk:~$ dash -c 'printf "%x\n" $((0xffffffff94100000 + 0x400000))'
80000000003fffff
----
The former is obviously correct whilst the later breaks things royally.
Fortunately working with only the lower 32bit's works for both bash and
dash:
----
$ bash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
$ dash -c 'printf "%x\n" $((0x94100000 + 0x400000))'
94500000
----
So, we can split the original 64bit string to two parts, and only
calculate the low 32bit part, which is big enough (1GiB kernel sizes
anyone?) for a normal Linux kernel image file, now, we calculate the
VMLINUZ_LOAD_ADDRESS like this:
1. if present, append top 32bit of VMLINUX_LOAD_ADDRESS" as a prefix
2. get the sum of the low 32bit of VMLINUX_LOAD_ADDRESS + VMLINUX_SIZE
This patch fixes vmlinuz kernel builds on systems where only a
32bit-only math shell is available.
Patch Changelog:
Version 2
- simplified method by using 'expr' for 'substr' and making it work
with dash once again
Version 1
- Revert the removals of '-n "$(VMLINUX_SIZE)"' to avoid the error
of "make clean"
- Consider more cases of the VMLINUX_LOAD_ADDRESS
Version 0
- initial release
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/861/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Patchwork: http://patchwork.linux-mips.org/patch/857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It moves to the same directory as the boot files in other formats.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Remove the .initrd section. The initrd section was already handled
when vmlinux was linked.
o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
sections. If .MIPS.options is not removed, kernels compiled with gcc
3.4.6 will not boot.
o Clean up the file format.
o Remove several other unneeded sections.
Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/785/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch helps to generate smaller kernel images for linux-MIPS,
Here is the effect when using lzma:
$ ls -sh vmlinux
7.1M vmlinux
$ ls -sh vmlinuz
1.5M vmlinuz
Have tested the 32bit kernel on Qemu/Malta and 64bit kernel on FuLoong
Mini PC. both of them work well. and also, tested by Alexander Clouter
on an AR7 based Linksys WAG54Gv2, and by Manuel Lauss on an Alchemy
board.
This -v2 version incorporate the feedback from Ralf, and add the
following changes:
1. add .ecoff, .bin, .erec format support
2. only enable it and the debug source code for the machines we tested
3. a dozen of fixups and cleanups
and if you want to enable it for your board, please try to select
SYS_SUPPORTS_ZBOOT for it, and if the board have an 16550 compatible
uart, you can select SYS_SUPPORTS_ZBOOT_UART16550 directly. and then
sending the relative patches to Ralf.
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
Tested-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Aaro Koskinen