Don't restrict display list usage to the DRM pipeline, use them
unconditionally. This prepares the driver to support the request API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Display lists can operate in header or headerless mode. The headerless
mode is only available on WPF0, to be used with the display engine. All
other WPF instances can only use display lists in header mode.
Implement support for header mode to prepare for display list usage on
WPFs other than 0.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can only be called from a s_stream handler as it requires a
valid display list context (due to calling vsp1_uds_set_alpha() which
writes to module registers). Document the requirement.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flag is set but never read, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RPF source memory pointers need to be offset to take the crop
rectangle into account. Offsets are computed in the RPF stream start,
which can happen (when using the DRM pipeline) after calling the RPF
.set_memory() operation that programs the buffer addresses.
The .set_memory() operation tries to guard against the problem by
skipping programming of the registers when the module isn't streaming.
This will however only protect the first use of an RPF in a DRM
pipeline, as in all subsequent uses the module streaming flag will be
set and the .set_memory() operation will use potentially incorrect
offsets.
Fix this by allowing the caller to decide whether to program the
hardware immediately or just cache the addresses. While at it refactor
the memory set code and create a new vsp1_rwpf_set_memory() that cache
addresses and calls the .set_memory() operation to apply them to the
hardware.
As a side effect the driver now writes all three DMA address registers
regardless of the number of planes, and initializes unused addresses to
zero.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those modules were left out of display list integration as they're not
used by the DRM pipeline. To prepare for display list support in non-DRM
pipelines use the module write API to set registers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The control handler set operations don't program the hardware anymore,
there's thus no need to call them when starting the stream.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The datasheet clearly states that all but a few registers can't be
modified when the device is running. Programming the intensity
parameters in the control set handler is thus prohibited. Program it
when starting the module instead.
This requires storing the intensity value internally as the module can
be started from the frame completion interrupt handler, and accessing
control values requires taking a mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The datasheet clearly states that all but a few registers can't be
modified when the device is running. Programming the alpha value in
the control set handler is thus prohibited. Program it when starting the
module instead.
This requires storing the alpha value internally as the module can be
started from the frame completion interrupt handler, and accessing
control values requires taking a mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/vsp1/vsp1_drm.c:39:6: warning: no previous prototype for 'vsp1_drm_frame_end' [-Wmissing-prototypes]
void vsp1_drm_frame_end(struct vsp1_pipeline *pipe)
Fixes: ef9621bcd6 ("[media] v4l: vsp1: Store the display list manager in the WPF")
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The datasheet clearly states that all but a few registers can't be
modified when the device is running. Programming the background color
in the control set handler is thus prohibited. Program it when starting
the module instead.
This requires storing the background color value internally as the
module can be started from the frame completion interrupt handler, and
accessing control values requires taking a mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Each WPF can process display lists independently, move the manager to
the WPF to reflect that and prepare for display list support for non-DRM
pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This clarifies the API and prepares display list support for being used
to implement the request API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DRM pipeline, as it runs in automatic restart mode, never sees the
pipeline state set to VSP1_PIPELINE_STOPPING or VSP1_PIPELINE_STOPPED
when running the frame end interrupt handler. We can thus skip the
checks various checks in the handler and return immediately.
Similarly the DRM frame end handler calls vsp1_pipeline_run()
unnecessarily, as the state there is never VSP1_PIPELINE_STOPPED. Remove
the function call and the frame end handler is it's now empty.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure display list usage is correctly disabled by always setting up
the corresponding registers, including when the display list feature
isn't used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the HAS_LUT flag in the corresponding device information entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 54b5a749b4 ("[media] v4l: vsp1: Use media entity enumeration
interface") wasn't aligned with the driver coding style. Fix it by
renaming the rval variable to ret.
Furthermore shorten lines by accessing the media_device instance in a
more straightforward fashion.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VSP1 DRM API is declared in <media/vsp1.h>, not <linux/vsp1.h>. Fix
it. This also reverts commit 18922936dc ("[media] vsp1_drm.h: add
missing prototypes") that added the same declarations in a different
header file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users of is_media_entity_v4l2_io() (the exynos4-is, omap3isp,
davince_vpfe and omap4iss drivers and the v4l2-mc power management code)
use the function to check whether entities are video_device instances,
either to ensure they can cast the entity to a struct video_device, or
to count the number of video nodes users.
The purpose of the function is thus to identify whether the media entity
instance is an instance of the video_device object, not to check whether
it can perform I/O. Rename it accordingly, we will introduce a more
specific is_media_entity_v4l2_io() check when needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add fallback compatibility string for R-Car Gen 1 and 2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and 3. But beyond that it's unclear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A dependency on ARCH_SHMOBILE seems to be the best option for
sh_mobile_ceu_camera:
* For Super H based SoCs: sh_mobile_ceu is used on SH_AP325RXA, SH_ECOVEC,
SH_KFR2R09, SH_MIGOR, and SH_7724_SOLUTION_ENGINE which depend on
CPU_SUBTYPE_SH7722, CPU_SUBTYPE_SH7723, or CPU_SUBTYPE_SH7724 which all
select ARCH_SHMOBILE.
* For ARM Based SoCs: Since the removal of legacy (non-multiplatform)
support this driver has not been used by any Renesas ARM based SoCs.
The Renesas ARM based SoCs currently select ARCH_SHMOBILE, however,
it is planned that this will no longer be the case.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Thanks to Geert Uytterhoeven for analysis and portions of the
change log text.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If we are doing V4L2_FIELD_NONE then "ret" is used uninitialized.
Fixes: 417d2e507e ('[media] media: platform: add VPFE capture driver support for AM437X')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
gcc-6 points out an obviously silly comparison in vpfe_get_app_input_index():
drivers/media/platform/am437x/am437x-vpfe.c: In function 'vpfe_get_app_input_index':
drivers/media/platform/am437x/am437x-vpfe.c:1709:27: warning: self-comparison always evaluats to true [-Wtautological-compare]
client->adapter->nr == client->adapter->nr) {
^~
This was introduced in a slighly incorrect conversion, and it's
clear that the comparison was meant to compare the iterator
to the current subdev instead, as we do in the line above.
Fixes: d37232390f ("[media] media: am437x-vpfe: match the OF node/i2c addr instead of name")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/exynos-gsc/gsc-core.c:1073 gsc_probe() warn: impossible condition '(gsc->id < 0) => (0-65535 < 0)'
drivers/media/platform/exynos-gsc/gsc-core.c: In function 'gsc_probe':
drivers/media/platform/exynos-gsc/gsc-core.c:1073:51: warning: comparison is always false due to limited range of data type [-Wtype-limits]
if (gsc->id >= drv_data->num_entities || gsc->id < 0) {
^
gsc->id is an u16, so it can never be a negative number. So,
remove the always false condition.
Fixes: c1ac057173 "[media] exynos-gsc: remove non-device-tree init code"
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mxr_layer_ops structures are never modified, so declare
them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exynos and Samsung S5P platforms has been fully converted to device
tree, so old platform device based init data can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exynos and Samsung S5P platforms has been fully converted to device
tree, so old platform device based init data can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exynos and Samsung S5P platforms has been fully converted to device
tree, so old platform device based init data can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exynos platform has been fully converted to device tree,
so old platform device based init data can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Eliminate iommu fault during encoding by adjusting image size
used for buffer size computation and ensuring that the buffer
is not overrun.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MIPI CSIS DT parse function return an -ENXIO errno if the port #
is outside of the supported values. But it doesn't call of_node_put()
to decrement the node's reference counter, that's incremented inside
the of_graph_get_next_endpoint() function that was called before.
Instead of just returning, go to the error path that already does it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In fimc_md_parse_port_node() remote port parent node is acquired with
of_graph_get_remote_port_parent() but it is not put on error path.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I noticed this while merging the drm tree and checking for stragglers:
the vsp1 driver still used dma_[alloc|free]_writecombine() that got
renamed in commit f6e45661f9 ("dma, mm/pat: Rename
dma_*_writecombine() to dma_*_wc()")
I should have noticed back in the media merge (commit bace3db5da), but
better late than never.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tPgH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Added support for some new video formats
- mn88473 DVB frontend driver got promoted from staging
- several improvements at the VSP1 driver
- several cleanups and improvements at the Media Controller
- added Media Controller support to snd-usb-audio. Currently, enabled
only for au0828-based V4L2/DVB boards
- Several improvements at nuvoton-cir: it now supports wake up codes
- Add media controller support to em28xx and saa7134 drivers
- coda driver now accepts NXP distributed firmware files
- Some legacy SoC camera drivers will be moving to staging, as they're
outdated and nobody so far is willing to fix and convert them to use
the current media framework
- As usual, lots of cleanups, improvements and new board additions.
* tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The driver verifies that the type of the remote entity matches its
expectations when setting up fimc-lite links and returns an error if it
doesn't. Those checks can never fail as the links are created by the
driver in a way that always match its expectations (the SINK and
SOURCE_ISP pads are connected to subdevs only and the SOURCE_DMA pad is
connected to a video node only). Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use is_media_entity_v4l2_subdev() instead of is_media_entity_v4l2_io()
to check whether the entity is a subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If we bail out this early, v4l2_device_register() has not been called
yet, so no need to call v4l2_device_unregister().
Fixes: b7bd660a51 ("[media] coda: Call v4l2_device_unregister() from a single location")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Power on devices represented by entities in the graph through the pipeline
state using V4L2 graph PM operations instead of what was in the omap3isp
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver is deprecated: it should become a stand-alone driver
instead of using the soc-camera framework.
Unless someone is willing to take this on (unlikely with such
ancient hardware) it is going to be removed from the kernel
soon.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver is deprecated: it should become a stand-alone driver
instead of using the soc-camera framework.
Unless someone is willing to take this on (unlikely with such
ancient hardware) it is going to be removed from the kernel
soon.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver is deprecated: it needs to be converted to vb2 and
it should become a stand-alone driver instead of using the
soc-camera framework.
Unless someone is willing to take this on (unlikely with such
ancient hardware) it is going to be removed from the kernel
soon.
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the new YUV422M, YVU422M, YUV444M and YVU444M formats.
This allows applications to check their support for these formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Try loading the firmware from firmware files named vpu_fw_imx*.bin, as
they are originally distributed by NXP. Fall back to v4l-coda*-imx6*.bin.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Freescale distribute their VPU firmware files with a 16 byte header
in BIT processor native order. This patch allows to detect the header
and to reorder the firmware on the fly.
With this patch it should be possible to use the distributed
vpu_fw_imx{53,6q,6d}.bin files directly after renaming them to
v4l-coda*-imx{53,6q,6dl}.bin.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IS_ERR_VALUE() assumes that its parameter is an unsigned long.
It can not be used to check if an unsigned int reflects an error.
Doing so can result in the following build warning.
drivers/media/platform/soc_camera/atmel-isi.c:
In function "atmel_isi_probe":
include/linux/err.h:21:38: warning:
comparison is always false due to limited range of data type
drivers/media/platform/soc_camera/atmel-isi.c:1089:6: note:
in expansion of macro "IS_ERR_VALUE"
If that warning is seen, the return value from platform_get_irq() is not
checked for errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert pxa_camera to dmaengine. This removes all DMA registers
manipulation in favor of the more generic dmaengine API.
The functional level should be the same as before. The biggest change is
in the sg_split() function, which splits a videobuf-dma into several
scatterlists for 3 planes captures (Y, U, V).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[g.liakhovetski@gmx.de: fix a function prototype, use bool, struct init]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This moves the dma irq handling functions up in the source file, so that
they are available before DMA preparation functions. It prepares the
conversion to DMA engine, where the descriptors are populated with these
functions as callbacks.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In preparation for dmaengine conversion, move the camera interrupt
handling into a tasklet. This won't change the global flow, as this
interrupt is only used to detect the end of frame and activate DMA fifos
handling.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the error path where the video buffer wasn't allocated nor
mapped. In this case, in the driver free path don't try to unmap memory
which was not mapped in the first place.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mx3_camera driver prints DMA addresses using the "%x" format
string, which is wrong when using a 64-bit dma_addr_t definition:
media/platform/soc_camera/mx3_camera.c: In function 'mx3_cam_dma_done':
media/platform/soc_camera/mx3_camera.c:149:125: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
media/platform/soc_camera/mx3_camera.c: In function 'mx3_videobuf_queue':
media/platform/soc_camera/mx3_camera.c:317:119: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
media/platform/soc_camera/mx3_camera.c: In function 'mx3_videobuf_release':
media/platform/soc_camera/mx3_camera.c:346:119: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Werror=format=]
This changes the code to use the special %pad format string, which
always does the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported ctx->sensor is being dereferenced before being checked
in cal_get_external_info(). That being the case it was also checked
twice in multiple other location where v4l2_subdev_call is already
checking it so no need to explicitly check it again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported, the current cal_enum_frameintervals() is confusing
and does not have the intended behavior.
Fix this by re-implementing to properly propagate the enum_frame_interval
request to the subdevice.
[mchehab@osg.samsung.com: remove a now bogus "ret = 0" statement]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The IP version number carries enough information to identify the exact
device instance features. Drop the related DT properties and use the IP
version instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Display lists contain lists of registers and associated values to be
applied atomically by the hardware. They lower the pressure on interrupt
processing delays when reprogramming the device as settings can be
prepared well in advance and queued to the hardware without waiting for
the end of the current frame.
Display list support is currently limited to the DRM pipeline.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DT compatible strings for the VSP2 instances found in the R-Car Gen3
SoCs and support them in the vsp1 driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add two API functions named vsp1_du_atomic_begin() and
vsp1_du_atomic_flush() to signal the start and end of an atomic update.
The vsp1_du_setup_rpf() function is renamed to vsp1_du_atomic_update()
for consistency.
With this new API, the driver will reprogram all modified inputs
atomically before restarting the video stream.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement internal control of the VSP pipeline to be used by the DU
DRM/KMS driver when using the VSP as an internal composer handled
through DRM/KMS only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As the pipeline is configured internally by the driver when the
userspace API is disabled its configuration can be trusted and link
validation isn't needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RPF and WPF alpha values are set through V4L2 controls and applied
when starting the video stream by a call to v4l2_ctrl_handler_setup().
As that function uses the control handler mutex it can't be called in
interrupt context, where the VSP+DU pipeline handler might need to
reconfigure the pipeline.
Set the alpha value manually in the RPF and WPF s_stream handler to
ensure that the hardware is properly configured even when controlled
without the userspace API. If the userspace API is enabled protect that
with the control lock to avoid race conditions with userspace.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pipeline inputs array stores pointers to all RPFs contained in the
pipeline. It's currently indexed contiguously by adding RPFs in the
order they are found during graph walk. This can't easily support
dynamic addition and removal of RPFs while streaming, which will be
required for combined VSP+DU support.
Make the array indexed by RPF index instead and skip NULL elements when
iterating over RPFs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The R-Car Gen3 SoCs include VSP instances dedicated to the DU that will
be controlled entirely by the rcar-du-drm driver through the KMS API. To
support that use case make the userspace V4L2 API optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Format information and the related helper function are not specific to
the V4L2 API, move them from vsp1_video.c to vsp1_pipe.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all VSP instances have a BRU on R-Car Gen3, make it optional. Set
the feature unconditionally for now, this will be fixed when adding Gen3
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The R-Car Gen3 family has 5-inputs BRUs, support them by making the
number of BRU inputs configurable.
As the driver assumes that the number of BRU inputs is equal to the
number of RPFs, replace the BRU_MAX_INPUTS macro with VSP1_MAX_RPF to
make the assumption apparent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function will be used by the DU code, move it out of vsp1_video.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 58f896d859 ("[media] v4l: vsp1: sru: Make the intensity
controllable during streaming") refactored the stream start code and
removed the SRU CTRL0 register write by mistake. Add it back.
Fixes: 58f896d859 ("[media] v4l: vsp1: sru: Make the intensity controllable during streaming")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename the VI6_DISP_IRQ_STA_DSE register bit to VI6_DISP_IRQ_STA_DST to
fix a typo and match the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Link creation will be handled differently for the DU pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to waste CPU cycles when the value we need is already available.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The code will be reused outside of vsp1_video.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those functions are specific to video nodes, rename them for
consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The code will be used to control the vsp1 driver from the DU driver
without using video nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To make the pipeline structure and operations usable without video
devices the frame end processing must be decoupled from struct
vsp1_video. Implement this by calling the video frame end function
indirectly through a function pointer in struct vsp1_pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The field is always equal to the num_inputs field plus one, remove the
duplicate.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only RPFs and WPFs can be associated with video nodes, don't waste
memory by storing the video pointer in all entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all VSP1 instances include a UDS. Make the renesas,#uds DT property
optional and accept a number of UDS equal to 0 as valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rwpf queue operation doesn't queue a buffer but sets the memory
address for the next run. Rename it to set_memory and pass it a new
structure independent of the video buffer than only contains memory
information.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To make the video device nodes optional we need to decouple the [rw]pf
instances from the video devices. Move video devices out of struct
vsp1_rwpf and instantiate them dynamically in the core driver code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The structure represent a vsp1 videobuf2 buffer, name it accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This removes the dependency of vsp1_rpf and vsp1_wpf on vsp1_video,
making it possible to reuse the operations without a V4L2 video device
node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the format from struct vsp1_video to struct vsp1_rwpf to prepare
for VSPD KMS support that will not instantiate V4L2 video device nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rwpf field contains a pointer to the rpf or wpf associated with the
video node. Instead of storing it as a vsp1_entity, store the
corresponding vsp1_rwpf pointer to allow accessing the vsp1_rwpf fields
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no need to spread the code across multiple source files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tri-planar memory formats store the Y, U and V components in separate
planes. The VSP hardware supports them, the driver now does too.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the following sparse warnings:
ti-vpe/cal.c:387:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:459:26: warning: incorrect type in return expression (different address spaces)
ti-vpe/cal.c:503:27: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:509:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:518:47: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:526:31: warning: incorrect type in argument 6 (different address spaces)
ti-vpe/cal.c:1807:24: warning: Using plain integer as NULL pointer
ti-vpe/cal.c:1844:16: warning: Using plain integer as NULL pointer
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is a new control V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME to
force an encoder key frame. It is the same as requesting
V4L2_MPEG_MFC51_VIDEO_FORCE_FRAME_TYPE_I_FRAME.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:492:28: error: implicit
declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_TI_CAL also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Fixes: 343e89a792 ("[media] media: ti-vpe: Add CAL v4l2 camera capture driver")
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).
One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.
As far as I can tell it was only used in an Intel demo board in 2009
using Meego:
http://www.chinait.com/intelcontent/intelprc/admin/PDFFile/20106411545.pdf
which has since been superseded.
Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Richard Röjfors <richard@puffinpack.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove an unnecassary cast in the argument to kfree.
Found using Coccinelle. The semantic patch used to find this is as follows:
//<smpl>
@@
type T;
expression *f;
@@
- kfree((T *)(f));
+ kfree(f);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
for_each_available_child_of_node and for_each_child_of_node perform an
of_node_get on each iteration, so to break out of the loop an of_node_put is
required.
Found using Coccinelle. The simplified version of the semantic patch
that is used for this is as follows:
// <smpl>
@@
local idexpression n;
expression e,r;
@@
for_each_available_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add fallback compatibility string.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
- V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
- Asynchronous sensor sub device registration
- DT support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes when a Bayer pixelformat is selected the rendering of the OSD text
by vivid was all wrong: every other line of the text was shifted by half the width
or more.
It turned out that to render Bayer formats the interleaved boolean is set to true
in the tpg. This mode indicates a semi-biplanar mode where two interleaved planes
are used to render the frame. From outside the tpg it looks like a single plane,
but internally it is two planes.
However, in the tpg_s_bytesperline() function the interleaved bool wasn't checked
and only the bytesperline value for plane 0 was updated. But for the interleaved
mode the same value has to be copied to bytesperline[1] as well.
The effect was that whatever old value was left in bytesperline[1] was used, which
caused all sorts of weird and seemingly unpredictable shifts.
Reported-by: Ove Brynestad <ovebryne@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
During the recent vb2_buffer restructuring, the calculation of the
buffer payload reported to userspace was accidentally broken for the
first encoded frame, counting only the length of the headers.
This patch re-adds the length of the actual frame data.
Fixes: 2d7007153f ("[media] media: videobuf2: Restructure vb2_buffer")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Jan Luebbe <jlu@pengutronix.de>
Cc: <stable@vger.kernel.org> # for v4.4 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stv6110x_devctl structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data type "int" was used by the variable "ret" in the
gsc_m2m_poll() function despite of the aspect that the type "unsigned int"
will usually be needed for the return value from a call of the
v4l2_m2m_poll() function.
Improve this implementation detail by addition of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Passing a physical address to free_pages() is a bad idea.
config_params->fault_pxl.fpc_table_addr is set to virt_to_phys()
of __get_free_pages() return value; what we should pass to free_pages()
is its phys_to_virt(). ccdc_close() does that properly, but
ccdc_update_raw_params() doesn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With CONFIG_V4L2=m and VIDEO_SAMSUNG_EXYNOS4_IS=y, we can select the
individual drivers as built-in code when that should not be possible:
drivers/built-in.o: In function `s5pcsis_set_fmt':
policy.c:(.text+0x13afdc): undefined reference to `v4l_bound_align_image'
drivers/built-in.o: In function `s5pcsis_probe':
policy.c:(.text+0x13b440): undefined reference to `v4l2_of_parse_endpoint'
policy.c:(.text+0x13b72c): undefined reference to `v4l2_subdev_init'
Changing VIDEO_SAMSUNG_EXYNOS4_IS to tristate means that the dependency
from CONFIG_V4L2 propates to the individual Kconfig symbols and they
can only be built as loadable modules if V4L2 or any other of the
dependencies itself is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
error: implicit declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some user space use cases result in kernel hangup on the HIC_OPEN_SENSOR
command write. In case when a minimalistic application is used for setting
up the streaming, the hangups occur only occasionally. In case of GStreamer
use cases it is always the case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to allow for automatic media device entities linking
from the level of libv4l plugin the open system call shouldn't
fail, as the libv4l plugins can begin their job not until it
succeeds.
This patch allows for leaving the pipeline not linked on
open and postpones verifying it to the moment when streamon
callback is called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ironically, 7d4020c3c4 ("[media] exynos4-is: fix some warnings when
compiling on arm64") fixed some format string bugs but introduced a
new one. buf_index is a simple int, so it should be printed with %d,
not %pad (which is correctly used for dma_addr_t).
Fixes: 7d4020c3c4 ("[media] exynos4-is: fix some warnings when compiling on arm64")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was found with the -RT patch enabled, but the fix should apply to
non-RT also.
Compilation error without this fix:
../drivers/media/platform/vsp1/vsp1_video.c: In function
'vsp1_pipeline_stopped':
../drivers/media/platform/vsp1/vsp1_video.c:524:2: error: expected
expression before 'do'
spin_unlock_irqrestore(&pipe->irqlock, flags);
^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.
This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum isp_pipeline_state versus
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Control framework now requires entities to be registered with
the media device before creating links so commit c7621b3044 ("[media]
v4l: vsp1: separate links creation from entities init") separated link
creation from entities init.
But unfortunately that patch introduced a regression since wrong links
were created causing a boot failure on Renesas boards.
This patch fixes the boot issue and also the media graph was compared
by Geert Uytterhoeven to make sure that the driver changes required by
the Media Control framework next generation did not affect the graph.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
Currently, v4l2_device_register() doesn't use the media_device
struct. So, calling media_device_init() could be called either
before or after v4l2_device_register().
Yet, it is a good practice to initialize everything before calling
the register functions. Also, the other drivers call
media_device_init() before registering the V4L2 device.
So, move the call for media_device_init() to happen earlier on
exynos4-is and s3c-camif.
This is just a cleanup patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device node is registered and so made visible to user-space
before entities are registered and links created which means that the
media graph obtained by user-space could be only partially enumerated
if that happens too early before all the graph has been created.
To avoid this race condition, split the media init and registration
in separate functions and only register the media device node when
all the pending subdevices have been registered, either explicitly
by the driver or asynchronously using v4l2_async_register_subdev().
The media_device_register() had a check for drivers not filling dev
and model fields but all drivers in mainline set them and not doing
it will be a driver bug so change the function return to void and
add a BUG_ON() for dev being NULL instead.
Also, add a media_device_cleanup() function that will destroy the
graph_mutex that is initialized in media_device_init().
[mchehab@osg.samsung.com: Fix compilation if !CONFIG_MEDIA_CONTROLLER
and remove two warnings added by this changeset]
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The for loop in the vsp1_create_entities() function that create the links,
checks the entity type and call the proper link creation function but then
it uses continue to force the next iteration of the loop to take place and
skipping code in between that creates links for different entities types.
It is more readable and easier to understand if the if else constructs is
used instead of the continue statement.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions that create entities links are called *_create_pads_links()
but the "pads" prefix is redundant since the driver doesn't handle any
other kind of link so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The isp_subdev_notifier_complete() complete callback defines a struct
v4l2_device *v4l2_dev to avoid needing two level of indirections to
access the V4L2 subdevs but the var is not always used when possible
as when calling v4l2_device_register_subdev_nodes().
So change that to consistently use the defined v4l2_dev pointer var.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bc36b30fe06b ("[media] omap3isp: separate links creation from
entities init") moved the link creation logic from the entities init
functions and so removed the error_link labels from the error paths.
But after that, some functions have a single error label so it makes
more sense to rename the label to just "error" in thi case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function that creates the links between ISP internal and external
entities is called isp_create_pads_links() but the "pads" prefix is
redundant since the driver doesn't handle any other kind of link so
it can just be removed.
While being there, fix the function's kernel-doc since is not using
a proper format.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entities to video nodes links were created on separate functions for
each ISP module but since the only thing that these functions do is to
call media_create_pad_link(), there's no need for that indirection level
and all link creation logic can be just inlined in the caller function.
Also, since the only possible failure for the link creation is a memory
allocation, there is no need for error messages since the core already
reports a very verbose message in that case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pad index is unsigned. Replace the occurences of it where
pertinent.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On omap3/omap4/davinci drivers, MEDIA_ENT_T_V4L2_SUBDEV macro is
abused in order to "simplify" the pad checks.
Basically, it does a logical or of this macro, in order to check
for a local index and if the entity is either a subdev or not.
As we'll get rid of MEDIA_ENT_T_V4L2_SUBDEV macro, replace it by
2 << 16 where it occurs, and add a note saying that the code
there is actually a hack.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on media subtype, use the new macros to detect
if an entity is a subdev or an A/V DMA entity.
Please note that most drivers assume that there's just AV_DMA or
V4L2 subdevs. This is not true anymore, as we've added MC support
for DVB, and there are plans to add support for ALSA and FB/DRM
too.
Ok, on the current pipelines supported by those drivers, just V4L
stuff are there, but, assuming that some day a pipeline that also
works with other subsystems will ever added, it is better to add
explicit checks for the AV_DMA stuff.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces and entities are distinct, it makes no sense
of keeping something named as MEDIA_ENT_T_DEVNODE.
This change was done with this script:
for i in $(git grep -l MEDIA_ENT_T|grep -v uapi/linux/media.h); do sed s,MEDIA_ENT_T_DEVNODE_V4L,MEDIA_ENT_T_V4L2_VIDEO, <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver initializes the entities and creates the pads links
before the entities are registered with the media device. This doesn't
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so are
made after the entities registration.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver creates the pads links before the media entities are
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver parses the graph endpoints to know how many subdevices
needs to be registered async and register notifiers callbacks for to know
when these are bound and when the async registrations are completed.
Currently the entities pad are linked with the correct ISP input interface
when the subdevs are bound but it happens before entitities are registered
with the media device so that won't work now that the entity links list is
initialized on device registration.
So instead creating the pad links when the subdevice is bound, create them
on the complete callback once all the subdevices have been bound but only
try to create for the ones that have a bus configuration set during bound.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver initializes the entities and creates the pads links
before the entities are registered with the media device. This does not
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so the links
are created after the entities have been registered with the media device.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity has a .parent field that stores a pointer
to the parent struct media_device. But recently a media_gobj was
embedded into the entities and since struct media_gojb already has
a pointer to a struct media_device in the .mdev field, the .parent
field becomes redundant and can be removed.
This patch replaces all the usage of .parent by .graph_obj.mdev so
that field will become unused and can be removed on a later patch.
No functional changes.
The transformation was made using the following coccinelle spatch:
@@
struct media_entity *me;
@@
- me->parent
+ me->graph_obj.mdev
@@
struct media_entity *link;
@@
- link->source->entity->parent
+ link->source->entity->graph_obj.mdev
@@
struct exynos_video_entity *ve;
@@
- ve->vdev.entity.parent
+ ve->vdev.entity.graph_obj.mdev
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Accessing media_entity ID should now use media_entity_id() macro to
obtain the entity ID, as a next patch will remove the .id field from
struct media_entity .
So, get rid of it, otherwise the omap3isp driver will fail to build.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of accessing directly entity.id, let's create a macro,
as this field will be moved into a common struct later on.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
omapfb's private copy of omapdss is now ready to be used.
This patch makes omapfb use its private omapdss and display drivers, and
also makes omap_vout (which uses omapfb) to depend on omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Hook up the MPEG-2 ES decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We could support start streaming with an empty output queue for the
BIT decoders due to the bitstream buffer which could still contain
data at this point, but there is really no reason for userspace to
expect this to work. Simplify the code by disallowing it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
coda_jpeg_check_buffer only cares about the buffer length and contents,
so change the parameter type back from v4l2_vb2_buffer to just the
vb2_buffer.
Instead of just checking the first and last bytes for the SOI and EOI
markers, relax the EOI marker check a bit and allow up to 32 trailing
bytes after the EOI marker as hardware generated JPEGs sometimes contain
some alignment overhead.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function is not used outside coda-common.c.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC register addresses are used only by writel/readl macros which already
takes care of proper register accessing.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both macros can be merged into one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC driver uses dev->irqlock spinlock to protect queues only, but many context
fields require protection also - they can be accessed concurrently
from IOCTLs and IRQ handler. The patch increases protection range of irqlock
to those fields also.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many version specific functions are not called by common code, so there
is no need to use callbacks. Additionally some of them are not used at all,
so they can be safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Code for queue cleanup has nothing specific to hardware version.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both version of MFC driver use functions with the same body and name.
The patch moves them to common location. It also simplifies it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s5p_mfc_codec_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All the davinci media drivers are using the i2c framework, and
fail to build if that is ever disabled, e.g.:
media/platform/davinci/vpif_display.c: In function 'vpif_probe':
media/platform/davinci/vpif_display.c:1298:14: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
This adds explicit Kconfig dependencies so we don't see the
driver options if I2C is turned off.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VRFB buffers are freed when the device is closed even if they
haven't been allocated by a call to VIDIOC_REQBUFS, resulting in a
crash. Fix it by not trying to free buffers that are not allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The variable "tsin" was checked three times in a loop iteration of the
c8sectpfe_tuner_unregister_frontend() function.
This implementation detail could be improved by the combination of the
involved statements into a single if block so that this variable will be
checked only once there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions i2c_put_adapter() and module_put() test whether their
argument is NULL and then return immediately.
Thus the tests around their calls are not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), Renesas R-Car SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that media has its own subdirectory inside platform_data,
let's move the headers that are already there to such subdir.
After moving those files, the references were adjusted using this
script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="linux/platform_data/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Give JPU peripheral chance to finish current job.
Don't switch off clock until context release.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove redundant code. Following code line do what we want.
[mchehab@osg.samsung.com: fix conflict with VB2 split patches that renamed some structs]
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The preview path only can convert UYVY format to RGB data.
To make preview path work correctly, we need to set up YCC_SWAP
according to sensor output and convert them to UYVY.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not like codec path, preview path can do downsampling, so we should setup
a extra preview width, height for it.
This patch add preview resolution setup without down sampling. So currently
preview path will output same size as sensor output size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Atmel ISI support a preview path which can output RGB data.
So this patch introduces a bool variable to choose which path is
enabled currently. And also we need setup corresponding path registers.
By default the preview path is disabled. We only use Codec path.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
we need to configure the YCC_SWAP bits in ISI_CFG2 according to current
sensor output and Atmel ISI output format.
Current there are two cases Atmel ISI supported:
1. Atmel ISI outputs YUYV format.
This case we need to setup YCC_SWAP according to sensor output
format.
2. Atmel ISI output a pass-through formats, which means no swap.
Just setup YCC_SWAP as default with no swap.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make all v4l2-clk's clock name use V4L2_CLK_NAME_SIZE definition.
In future, if the string is increased we just need to change the
V4L2_CLK_NAME_SIZE once.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This macro is used to generate an OF string for a v4l2 clock.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With this patch, vivid capture thread can now generate a video with
frame rate reduced by a factor of 1000 / 1001. This option can be
selected using a control Reduced Framerate from gui.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A boolean control Reduced Framerate is added to vivid controls for
controlling the reduced fps option for vivid capture from gui.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If reduced fps flag is set then check if other necessary conditions
are true for the given bt timing. If yes, then reduce the frame rate.
For vivid transmitter, timeperframe_vid_out controls the frame rate.
Adjusting the timeperframe_vid_out by scaling down pixel clock by
factor of 1000 / 1001.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sh-vou driver has been converted from videobuf to videobuf2, but
the Kconfig file still lists VIDEOBUF_DMA_CONTIG as a dependency.
Consequently we can build the driver without VIDEOBUF2_DMA_CONTIG
and get a link error:
drivers/built-in.o: In function `sh_vou_probe':
vf610-ocotp.c:(.text+0x2dbf5c): undefined reference to `vb2_dma_contig_init_ctx'
vf610-ocotp.c:(.text+0x2dc0b4): undefined reference to `vb2_dma_contig_cleanup_ctx'
vf610-ocotp.c:(.text+0x2dc144): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `sh_vou_remove':
vf610-ocotp.c:(.text+0x2dc190): undefined reference to `vb2_dma_contig_cleanup_ctx'
This changes the dependency to VIDEOBUF2_DMA_CONTIG instead.
Fixes: 57af3ad59d ("[media] sh-vou: convert to vb2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Laurent Pinchart