The PFC SH7724 SoC data contains a input_pu range used to configure
pull-up resistors using the legacy non-pinconf API. That API has been
removed from the driver, the range is thus not used anymore. Remove it.
If required, configuring pull-up resistors for the SH7724 can be
implemented using the pinconf API, as done for the SH-Mobile, R-Mobile
and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The PFC SH7723 SoC data contains a input_pu range used to configure
pull-up resistors using the legacy non-pinconf API. That API has been
removed from the driver, the range is thus not used anymore. Remove it.
If required, configuring pull-up resistors for the SH7723 can be
implemented using the pinconf API, as done for the SH-Mobile, R-Mobile
and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The PFC SH7722 SoC data contains input_pd and input_pu ranges used to
configure pull-down and pull-up resistors using the legacy non-pinconf
API. That API has been removed from the driver, the ranges are thus not
used anymore. Remove them.
If required, configuring pull-down and pull-up resistors for the SH7722
can be implemented using the pinconf API, as done for the SH-Mobile,
R-Mobile and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The PFC SH7720 SoC data contains a input_pu range used to configure
pull-up resistors using the legacy non-pinconf API. That API has been
removed from the driver, the range is thus not used anymore. Remove it.
If required, configuring pull-up resistors for the SH7720 can be
implemented using the pinconf API, as done for the SH-Mobile, R-Mobile
and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The PFC pinctrl driver on sh73a0 is also regiatering a VccQ regulator for
SDHI0. However, its consumers list only included the platform-data based
SDHI device name. When booted with DT SDHI0 couldn't enable VccQ and
therefore was unusable. Fix this by adding a consumer with DT-based name.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
Fix a compilation error caused by pinconf_generic_parse_dt_config() not
being defined on !CONFIG_OF platforms by guarding the whole DT node
parsing code with #ifdef CONFIG_OF.
Defining a pinconf_generic_parse_dt_config() on !CONFIG_OF would have
been possible as well, but would have resulted in a larger code size on
!CONFIG_OF platforms (such as arch/sh).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support device instantiation through the device tree. The compatible
property is used to select the SoC pinmux information.
Set the gpio_chip device field to the PFC device to enable automatic
GPIO OF support.
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinmux groups and functions for the two MMCIF and three
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The list of functions selected by the MOD_SEL2 register was missing
an entry. This caused all entries after this to modify the MOD_SEL2
register incorrectly.
This bug showed up when selecting i2c2_c pins on the Renesas Hurricane board.
This bug has been present since pinmux support was added for the
r8a7779 SoC by 881023d28b ("sh-pfc: Add
r8a7779 pinmux support") in v3.8-rc4.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pinmux groups and functions for the two MMCIF and four
SDHI interfaces on r8a73a4 (APE6).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix several errors in Peripheral Function Select register tables for
r8a7790, which prevent various function pins from being correctly
configured.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
IP2[31] func2 is IRQ1A, not IRQ3A
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN DATA[0:8]/CLK/HSYNC/VSYNC pin groups to R8A7778 PFC driver.
While at it, add SH_PFC_MUX8() macro for 8-bit data busses.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
[Sergei: updated the copyrights, added SH_PFC_MUX8() macro for 8-bit data bus,
made use of SH_PFC_*() macros to define the pin groups.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No sh73a0 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 has an internal power gate on the VCCQ power supply for the
SDHI0 device that is controlled (for some strange reason) by a bit in a
PFC register. This feature should be exposed as a regulator.
As the same register is also used for pin control purposes there is no
way to achieve atomic read/write sequences with a separate regulator
driver. We thus need to implement the regulator here.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add two optional init and exit SoC operations and call them from the
core at probe and remove time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Function GPIOs have been removed, remove comments that refer to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7740 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the HDMI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the FSI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the CEU pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the GETHER
pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the BSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the SCIF pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7740 has two LCDC units and two sets of LCDC output signals. By
default LCDC0 is routed to the LCD0 signals, and LCDC1 to the LCD1
signals. However, LCDC1 can be routed to the LCD0 signals by setting bit
MSEL6 in MSEL3CR (the LCD0 signals are further pinmuxed the usual way).
This could be configured by duplicating the LCD0 pin groups for LCDC1.
However, this would unnecessarily complicate the LCD pin groups, as no
r8a7740 board supported in mainline use such a configuration. Hardcode
the MSEL3CR MSEL6 bit to 0 for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the INTC pin groups the INTC function hasn't been added to
the functions list. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No sh7372 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
pfc-r8a7778 will have many devices pfc support in the future,
and current pfc-r8a7778 is using pin/mux definition macro for SCIF.
The device definition style using macro is readable code IMO,
but creating new macro for each devices is not good sense.
This patch adds common SH_PFC_xx() macro for each new feature devices
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN DATA[0:7]/CLK/HSYNC/VSYNC pin groups to R8A7779 PFC driver.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: trivial rebase on top of
"sh-pfc: r8a7779: Don't group USB OVC and PENC pins"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the RCAR_GP_PIN macro to convert from the documentation pin number
space to the linear pinctrl space.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIFA1 as preparation to switch to pinctrl in board files.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7790.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7770 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: fixed typo in changelog: r8a7779 -> r8a7770]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make GPIO support optional for platforms that don't support GPIOLIB.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add all necessary entries to support the external IRQs from the INTC.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a7790 SoC.
At this point only GPIO interface is supported, move to
newer interfaces planned as incremental changes.
Original authors is Koji Matsuoka-san, thanks for him
and his team for the heavy lifting. Adjusted by Magnus
to work together with updated code in drivers/pinctrl.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@rms.renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The USB_OVCn pins are alternate options for USB over-current detection
when using a 3.3V USB interface. As they're not mandatory they can be
used independently of the USB PENC pins. Don't group the USB_OVCn and
PENC pins to avoid conflicts when the USB_OVCn pins are used by another
function.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Remove unused pull-up/down data from the r8a73a4 PFC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a73a4 platforms use the pinctrl API to control pin functions.
Function GPIOs are no longer needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 board support will use the pinctrl API to control the
external IRQ pins so remove the unused function GPIOS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 board support will use the pinctrl API to control the SCIF
pins, remove the corresponding unused function GPIOS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V2 of PINCTRL support for r8a73a4 IRQC hardware
and in particular the external pins IRQ0 -> IRQ57.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Implement pull-up/down support for r8a73a4 similar to the implementation
for sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V2 of code to add GPIO -> IRQ mappings to the
PFC table for the r8a73a4 SoC. Requires the IRQs
to be mapped at a fixed location in Linux IRQ
space. The actual IRQs are not handled by the
PFC, instead IRQC is used on r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a73a4 SoC.
At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.
Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The output pixel clocks can be used without the input pixel clocks.
Split them in different groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When a GPIO is handled by a separate driver the pinmux
gpio_set_direction() handler won't be called. The pin mux type then need
to be configured to GPIO at request time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.
This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.
If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7779.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7779 platforms use the pinctrl API to control functions. Function
GPIOs are unused and unneeded, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh_pfc_phys_to_virt() function ends with a BUG() statement without a
return. When CONFIG_BUG isn't set the function will thus have no return
value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Conflicts:
drivers/pinctrl/sh-pfc/pfc-r8a7740.c
This merge is to provide r8a73a4 SoC files, which are added in the
soc branch and depended on by r8a73a4 pfc-changes which are to
be added to the pinmux branch.
With the added capabilty of the intc_irqpin driver to handle shared
external IRQs, all prerequisites are fulfilled and we are ready to
migrate completely to GIC. This includes the following steps:
- Kconfig: select ARM_GIC and RENESAS_INTC_IRQPIN
- intc-r8a7740: Throw out all legacy INTC code and init the GIC. We need
to mask out all shared IRQs as it is needed by the
shared intc_irqpin driver.
- setup-r8a7740: Add 4 irqpin devices to handle external IRQs and update
all IRQ numbers to point to the GIC SPI.
- board-armadillo: Update all IRQ numbers to point to the GIC SPI.
- pfc-r8a7740: Update all IRQ numbers of the GPIOs to point to the GIC
SPI.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.
This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7779 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7779 platforms now use the pinctrl API to control the LBSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7779 platforms now use the pinctrl API to control the USB pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7779 platforms now use the pinctrl API to control the HSPI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7779 platforms now use the pinctrl API to control the SCIF pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7779 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The function is not documented in the r8a7779 datasheet. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7740 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All r8a7740 platforms now use the pinctrl API to control the LCD0 and
LCD1 pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the IrDA pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the USB pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the BSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the KEYSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinconf API to control pull-ups, the
corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the FSI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the I2C pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the SCIFA and
SCIFB pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh73a0 platforms now use the pinctrl API to control the LCD and
LCD2 pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
All sh7372 platforms now use the pinctrl API to control the SDHI and
MMCIF pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Only the CS pins and functions are currently handled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pin groups for the first two SDHI interfaces and two alternative pin
groups for the MMCIF interface on the r8a7740 SoC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add pin groups for all three SDHI interfaces and two alternative pin
groups for the MMCIF interface on the sh7372 SoC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When setting a pin direction verify that the requested direction is
supported, and return an error if it isn't.
This requires pin configuration information to be supplied by SoC data.
The check is a no-op if the information is not supplied.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Set pin configuration type to
- PINMUX_TYPE_NONE at initialization time and when disabling a function
or freeing a GPIO
- PINMUX_TYPE_FUNCTION when enabling a function
- PINMUX_TYPE_INPUT or PINMUX_TYPE_OUTPUT when setting the GPIO
direction
Verify that the type is PINMUX_TYPE_NONE when enabling a function or
requesting a GPIO and return -EBUSY if it isn't.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Laurent Pinchart