Send frames back on the same port for XDP_TX action.
Since the frame buffers have been allocated by us, we can recycle
them directly into the Rx buffer pool instead of requesting a
confirmation frame upon transmission complete.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support enqueueing Rx FDs back to hardware, we need to
DMA map Rx buffers as bidirectional.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of freeing the RX buffers, release them back into the pool.
We wait for the maximum number of buffers supported by a single
release command to accumulate before issuing the command.
Also, don't unmap the Rx buffers at the beginning of the Rx routine
anymore, since that would require remapping them before release.
Instead, just do a DMA sync at first and only unmap if the frame is
meant for the stack.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll use function free_bufs() on the XDP path as well, so move
it higher in order to avoid a forward declaration.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve XDP_PACKET_HEADROOM bytes in Rx buffers to allow XDP
programs to increase frame header size.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We keep one XDP program reference per channel. The only actions
supported for now are XDP_DROP and XDP_PASS.
Until now we didn't enforce a maximum size for Rx frames based
on MTU value. Change that, since for XDP mode we must ensure no
scatter-gather frames can be received.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy reported when CONFIG_PROC_FS is not enabled:
ld: net/ipv4/af_inet.o: in function `inet_init':
af_inet.c:(.init.text+0x42d): undefined reference to `raw_init'
Fix by moving the endif up to the end of the proc entries
Fixes: 6897445fb1 ("net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
bnx2x: Popoulate firmware versions in driver info query.
The patch series populates MBI and storm firware versions in the ethtool
driver info query.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch populates the Storm FW version in the ethtool driver query data.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch populates the MBI version in the ethtool driver query data.
Adding 'extended_dev_info_shared_cfg' structure describing the nvram
structure, this is required to access the mbi version string.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one caller needs to pull TCP headers, so lets
move __skb_pull() to the caller side.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port 0/1 of HiP08 supports 10G and 25G. This patch adds a
change to configure NIC port speed same as that of optical
module(SFP/QFSP). Driver gets the optical module speed and
sets NIC port speed accordingly.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
Ease to interpret net-nsid
The goal of this series is to ease the interpretation of nsid received in
netlink messages from other netns (when the user uses
NETLINK_F_LISTEN_ALL_NSID).
After this series, with a patched iproute2:
$ ip netns add foo
$ ip netns add bar
$ touch /var/run/netns/init_net
$ mount --bind /proc/1/ns/net /var/run/netns/init_net
$ ip netns set init_net 11
$ ip netns set foo 12
$ ip netns set bar 13
$ ip netns
init_net (id: 11)
bar (id: 13)
foo (id: 12)
$ ip -n foo netns set init_net 21
$ ip -n foo netns set foo 22
$ ip -n foo netns set bar 23
$ ip -n foo netns
init_net (id: 21)
bar (id: 23)
foo (id: 22)
$ ip -n bar netns set init_net 31
$ ip -n bar netns set foo 32
$ ip -n bar netns set bar 33
$ ip -n bar netns
init_net (id: 31)
bar (id: 33)
foo (id: 32)
$ ip netns list-id target-nsid 12
nsid 21 current-nsid 11 (iproute2 netns name: init_net)
nsid 22 current-nsid 12 (iproute2 netns name: foo)
nsid 23 current-nsid 13 (iproute2 netns name: bar)
$ ip -n bar netns list-id target-nsid 32 nsid 31
nsid 21 current-nsid 31 (iproute2 netns name: init_net)
v3 -> v4:
- patch 5/5: fix imbalance lock in error path
v2 -> v3:
- patch 5/5: account NETNSA_CURRENT_NSID in rtnl_net_get_size()
v1 -> v2:
- patch 1/5: remove net from struct rtnl_net_dump_cb
- patch 2/5: new in this version
- patch 3/5: use a bool to know if rtnl_get_net_ns_capable() was called
- patch 5/5: use struct net_fill_args
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the previous patch, the goal is to ease to convert nsids from one
netns to another netns.
A new attribute (NETNSA_CURRENT_NSID) is added to the kernel answer when
NETNSA_TARGET_NSID is provided, thus the user can easily convert nsids.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combined with NETNSA_TARGET_NSID, it enables to "translate" a nsid from one
netns to a nsid of another netns.
This is useful when using NETLINK_F_LISTEN_ALL_NSID because it helps the
user to interpret a nsid received from an other netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like it was done for link and address, add the ability to perform get/dump
in another netns by specifying a target nsid attribute.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory work. To avoid having to much arguments for the
function rtnl_net_fill(), a new structure is defined.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used anymore.
Fixes: cab3c8ec8d ("netns: always provide the id to rtnl_net_fill()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed* enhancements series
The patch series add few enhancements to qed/qede drivers.
Changes from previous versions:
-------------------------------
v3: Revert v2 changes as the other paths (i.e. ptp) access the same data in
atomic context.
v2: Use __set_bit()/__clear_bit() where data access doesn't need to be
atomic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for MBI image update through MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of internal reload (e.g., mtu change), there could be a race
between link-up notification from mfw and the driver unload processing. In
such case kernel assumes the link is up and starts using the queues which
leads to the server crash.
Send link notification to the kernel only when driver has already requested
MFW for the link.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values represented by qede->flags is being used in mixed ways:
1. As 'value' at some places e.g., QEDE_FLAGS_IS_VF usage
2. As bit-mask(value) at some places e.g., QEDE_FLAGS_PTP_TX_IN_PRORGESS
usage.
This implementation pose problems in future when we want to add more flag
values e.g., overlap of the values, overflow of 64-bit storage.
Updated the implementation to go with approach (2) for qede->flags.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW sends UFP notifications mostly during the device init phase and PFs
might not be assigned with a name by this time. Hence capturing port-id in
the debug messages would help in finding which PF the ufp notification was
sent to.
Also, fixed a minor scemantic issue in a debug print.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
Add support for Aquantia AQtion USB to 5/2.5GbE devices
This patchset introduces support for new multigig ethernet to USB dongle,
developed jointly by Aquantia (Phy) and ASIX (USB MAC).
The driver has similar structure with other ASIX MAC drivers (AX88179), but
with a number of important differences:
- Driver supports both direct Phy and custom firmware interface for Phy
programming. This is due to different firmware modules available with
this product.
- Driver handles new 2.5G/5G link speed configuration and reporting.
- Device support all speeds from 100M up to 5G.
- Device supports MTU up to 16K.
Device supports various standard networking features, like
checksum offloads, vlan tagging/filtering, TSO.
The code of this driver is based on original ASIX sources and was extended
by Aquantia for 5G multigig support.
Patchset v2 includes following changes:
- Function variables declarions fixed to reverse xmass tree
- Improve patch layout structure
- Remove unnecessary curly braces in switch/case statements
- Use 'packed' attribute for HW structures only
- Use eth_mac_addr function in set_mac_addr callback
- Remove unnecessary 'memset' calls.
- Read MAC address from EEPROM function has now better name
- Use driver_priv field to store context. It avoids ugly cast.
- Set max_mtu field. Remove check for MTU size
- Rewrite read/write functions. Add helpers for read/write 16/32 bit values
- Use mask and shifts instead of bitfields to support BE platforms.
- Use stack allocated buffer for configuring mcast filters
- Use AUTONEG_ENABLE when go to suspend state
- Pad out wol_cfg field from context structure. Use stack allocated instead
- Remove driver version
- Check field 'duplex' in set_link_ksetting callback as well
- Use already created defines in usb matching macro
- Rename phy_ops struct to phy_cfg
- Use ether_addr_copy for copying mac address
- Add fall-through comment in switch/case for avoid checkpatch warning
- Remove match for CDC ether device
- Add ASIX's HW id-s to match this driver
- Add all HW id-s with which driver can work to blacklist of cdc_ether driver
Patchset v3 includes following changes:
- Use linkmode_copy instead of bitmap_copy
- Remove Direct PHY access code since production HW will not have this
mode anymore
- Fix line over 80 symbols and alignments in cdc_ether patch
- Add match for ECM configuration
On start our HW reports both ECM and vendor configs.
Linux prefers to use ECM driver and chooses active configuration
which is for ecm driver (not for vendor specific).
We need to match this configuration and forcibly switch configuration
to vendor specific.
Patchset v4 includes following changes:
- Set gso_max_size.
- Optimize accessing to descriptors
- Use SKB_TRUESIZE macro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Aquantia and ASIX device IDs to prevent loading cdc_ether for
these devices. Our firmware reports CDC configuration simultaneously
with vendor specific.
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It enables driver for ASIX products which are also based on
aqc111/112U chips.
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement get_drvinfo, set/get_msglevel, get_link callbacks
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add full hardware initialization sequence and link configuration logic
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to write 32bit values.
Implement PHY power up/down sequences.
AQC111, PHY is being controlled via vendor command interface.
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset, stop callbacks, driver unbind callback.
More register defines required for these callbacks.
Add helpers to read/write 16bit values
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read/write command register defines and functions
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize net_device_ops structure
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize usb_driver structure skeleton
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Prepare for VLAN-aware bridge w/VxLAN
The driver is using 802.1Q filtering identifiers (FIDs) to represent the
different VLANs in the VLAN-aware bridge (only one is supported).
However, the device cannot assign a VNI to such FIDs, which prevents the
driver from supporting the enslavement of VxLAN devices to the
VLAN-aware bridge.
This patchset works around this limitation by emulating 802.1Q FIDs
using 802.1D FIDs, which can be assigned a VNI and so far have only been
used in conjunction with VLAN-unaware bridges.
The downside of this approach is that multiple {Port,VID}->FID entries
are required, whereas a single VID->FID entry is required with "true"
802.1Q FIDs.
First four patches introduce the new FID family of emulated 802.1Q FIDs
and the associated type of router interfaces (RIFs). Last patch flips
the driver to use this new FID family.
The diff is relatively small because the internal implementation of each
FID family is contained and hidden in spectrum_fid.c. Different internal
users (e.g., bridge, router) are aware of the different FID types, but
do not care about their internal implementation. This makes it trivial
to swap the current implementation of 802.1Q FIDs with the new one,
using 802.1D FIDs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 802.1Q FIDs and VLAN RIFs with their emulated counterparts.
The emulated 802.1Q FIDs are actually 802.1D FIDs and thus use the same
flood tables, of per-FID type. Therefore, add 4K-1 entries to the
per-FID flood tables for the new FIDs and get rid of the FID-offset
flood tables that were used by the old 802.1Q FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu