This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Additionally to increasing #size-cells to in the root node, we also
need to explicitly define the ranges property in the plb node, because
of the different #size-cells between child and parent.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adding tx/rx-fifo-size-gige to EMAC fields for evaluation kit DTS
files where appropriate.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 'fsl5200-clocking'-property was dropped since
0d1cde2358. Remove all occurences
in dts-files.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- I2C with PCF8563 and Temp. Sensor ADM9240
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (30 commits)
Use macros for .data.page_aligned section.
Use macros for .bss.page_aligned section.
Use new __init_task_data macro in arch init_task.c files.
kbuild: Don't define ALIGN and ENTRY when preprocessing linker scripts.
arm, cris, mips, sparc, powerpc, um, xtensa: fix build with bash 4.0
kbuild: add static to prototypes
kbuild: fail build if recordmcount.pl fails
kbuild: set -fconserve-stack option for gcc 4.5
kbuild: echo the record_mcount command
gconfig: disable "typeahead find" search in treeviews
kbuild: fix cc1 options check to ensure we do not use -fPIC when compiling
checkincludes.pl: add option to remove duplicates in place
markup_oops: use modinfo to avoid confusion with underscored module names
checkincludes.pl: provide usage helper
checkincludes.pl: close file as soon as we're done with it
ctags: usability fix
kernel hacking: move STRIP_ASM_SYMS from General
gitignore usr/initramfs_data.cpio.bz2 and usr/initramfs_data.cpio.lzma
kbuild: Check if linker supports the -X option
kbuild: introduce ld-option
...
Fix trivial conflict in scripts/basic/fixdep.c
eSDHC block in MPC837x SOCs reports inverted write-protect state, soon
sdhci-of driver will look for sdhci,wp-inverted properties to decide
whether apply a specific quirk.
So, document the property and add it to device tree source files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the use of CROSS_COMPILE to select a customized
installkernel script with the possibility to set INSTALLKERNEL
to select a custom installkernel script when running make:
make INSTALLKERNEL=arm-installkernel install
With this patch we are now more consistent across
different architectures - they did not all support use
of CROSS_COMPILE.
The use of CROSS_COMPILE was a hack as this really belongs
to gcc/binutils and the installkernel script does not change
just because we change toolchain.
The use of CROSS_COMPILE caused troubles with an upcoming patch
that saves CROSS_COMPILE when a kernel is built - it would no
longer be installable.
[Thanks to Peter Z. for this hint]
This patch undos what Ian did in commit:
0f8e2d62fa
("use ${CROSS_COMPILE}installkernel in arch/*/boot/install.sh")
The patch has been lightly tested on x86 only - but all changes
looks obvious.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin]
Acked-by: Russell King <linux@arm.linux.org.uk> [arm]
Acked-by: Paul Mundt <lethal@linux-sh.org> [sh]
Acked-by: "H. Peter Anvin" <hpa@zytor.com> [x86]
Cc: Ian Campbell <icampbell@arcom.com>
Cc: Tony Luck <tony.luck@intel.com> [ia64]
Cc: Fenghua Yu <fenghua.yu@intel.com> [ia64]
Cc: Hirokazu Takata <takata@linux-m32r.org> [m32r]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Kyle McMartin <kyle@mcmartin.ca> [parisc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> [powerpc]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Cc: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Ingo Molnar <mingo@redhat.com> [x86]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To support cuImage, we need to initialize the required sections and
ensure that it is built.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For cuImage format it's necessary to provide clock fixups since u-boot will
not pass necessary clock frequency into the dtb included into cuImage so we
implement the clock fixups as defined in the technical documentation for the
board and update header file with the basic register definitions.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the ESTeem 195E Hotfoot SBC.
There are several variants of the SBC deployed, single/dual
ethernet+serial, and also 4MB/8MB flash variations. In the interest of
having a single kernel image boot on all boards, the cuboot shim detects
the differences and mangles the DTS tree appropriately.
With the exception of the CF interface that was never populated on
production boards, this code/DTS supports all boardpop options.
Signed-off-by: Solomon Peachy <solomon@linux-wlan.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the AMCC (AppliedMicro) PPC460SX Eiger evaluation
board.
Signed-off-by: Tai Tri Nguyen <ttnguyen@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Tirumala Marri <tmarri@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds some nodes to the AMCC Arches dts:
- L2 cache support
- NOR FLASH mapping with default partitioning
- I2C HWMON device (AD7414)
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch simply adds sdhci node to the device tree.
We specify clock-frequency manually, so that eSDHC will work without
upgrading U-Boot. Though, that'll only work for default setup (1500
MHz) on new board revisions. For non-default setups, it's recommended
to upgrade U-Boot, since it will fixup clock-frequency automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0
in the GUTS. The generic reboot code uses this tag to
determine if it should be using the RSTCR for reboot, so
remove it from the board definition.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allows interrupts to occur on the sbc834x. Currently PCI devices
get assigned an incorrect IRQ and so the interrupt count never
increases. This was tested with the 82546GB based dual port E1000
PCI-X NIC which uses two distinct IRQ lines on the one card.
root@localhost:/root> cat /proc/interrupts | grep eth
17: 78 IPIC Level eth1
48: 27121 IPIC Level eth0
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x
local bus, so add a localbus node in DTS with MTD partitions.
The recent U-boot commit fe613cdd4eb moves u-boot to the beginning
of flash, hence the legacy label on the partition at the end of flash.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since only one of the SoC USB devices is brought out to a physical
connector on the board, remove the 2nd (USB-DR) node from the DTS.
Having it present and USB enabled will cause a hang at boot.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update GE Fanuc DTS to match the alterations suggested during the merge of
the ppc9a DTS in commit 740d36ae63
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables the XMC (PCIe daughter card) site on the SBC310.
STG enter the description for the patch above.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch simply adds four eeprom nodes to MPC8548CDS' device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- add I2C support
- add FCC1 and FCC2 support
- fix bogus gpio numbering in plattform code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Added a device tree that should be similiar to mpc8536ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8536ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the following devices to the Kilauea dts:
- PPC4xx NAND controller (NDFC)
- I2C RTC (Dallas DS1338)
- I2C HWMON (Dallas DS1775)
Additionally the partitioning of the NOR FLASH is changed. The dtb
partition has been missing. Fixed in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also some whitespace cleanup in the USB device nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dtc was moved in 9fffb55f66 from
arch/powerpc/boot/ to scripts/dtc/
This patch updates the wrapper script to point to the new location of dtc.
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GPIO LEDS driver now has a default state of "keep". Update the Warp DTS
and platform file to take advantage of this new state. This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The kernel reserves the I/O address space from 0x0 to 0xfff for legacy
ISA devices. Change the ranges property for the PCI2ISA bridge to match
the kernels behavior, even if the ranges property isn't used for now.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Have git ignore generated files from dtc compile
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards,
so make 1-bit mode default. When we resolve the issue, u-boot will
remove sdhci,1-bit-only property from the device tree, while SDHCI
will still work with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node for the i2c eeprom and delete the superflous gpio-example.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some XPedite52xx boards have a legacy boot loader requiring some special
care in the boot wrapper. The use of cuboot-85xx is needed to fix
up embedded device trees, and a custom link address is specified to
accommodate the boot loader and larger kernel image sizes used on X-ES
MPC85xx platforms.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree source files for various MPC85xx boards from Extreme
Engineering Solutions. Supported boards include XPedite5370,
XPedite5200, XPedite5301, XPedite5330, and XCalibur1501.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.
This series provides the following functionality:
- The board can boot with a serial console on UART1
- Ethernet:
UCC1 in RGMII mode
UCC2 in RGMII mode
UCC4 in RMII mode
UCC5 in RMII mode
UCC6 in RMII mode
UCC7 in RMII mode
UCC8 in RMII mode
following patch is necessary for working UCC in RMII mode:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html
- Flash accessed via MTD layer
On this hardware there is an Intel P30 flash, following patch
series is necessary for working with this hardware:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html
- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 4 partitions in nor flash. Also fix nor flash bank width bug. The
flash is capable of x8/x16 width but is configured for x8.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some MPC85xx platforms do support 4 ethernet ports, so make sure the boot
wrapper fixes up all of them in the fdt.
Since MAC addresses are at the end of the bd_t structure there is no harm
in expanding to support 4 MAC address on older 85xx systems that might not
have that many.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.
Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Tested-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of commit 404614728f ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.
This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.
Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If anything goes wrong when copying images into the install path, then
the install script should exit with an error code so that 'make' knows
about it and tells the user.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As subject says, add dts files for Xilinx ML510 reference design with
the PCI host bridge device.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that the 4xx NAND driver is available again in arch/powerpc, let's
enable it on Sequoia. This patch also disables the early debug messages
(CONFIG_PPC_EARLY_DEBUG) in the Sequoia defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.
One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.
The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary. By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For serial flash support we need to:
- Add QE Par IO Bank E device tree node, a GPIO from this bank is
used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").
Also add node for NAND support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level. It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
The mktree utility defines some variables as "uint", although this is not a
standard C type, and so cross-compiling on Mac OS X fails. Change this to
"unsigned int".
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc kernel always requires an Open Firmware like device tree
to supply device information. On systems without OF, this comes from
a flattened device tree blob. This blob is usually generated by dtc,
a tool which compiles a text description of the device tree into the
flattened format used by the kernel. Sometimes, the bootwrapper makes
small changes to the pre-compiled device tree blob (e.g. filling in
the size of RAM). To do this it uses the libfdt library.
Because these are only used on powerpc, the code for both these tools
is included under arch/powerpc/boot (these were imported and are
periodically updated from the upstream dtc tree).
However, the microblaze architecture, currently being prepared for
merging to mainline also uses dtc to produce device tree blobs. A few
other archs have also mentioned some interest in using dtc.
Therefore, this patch moves dtc and libfdt from arch/powerpc into
scripts, where it can be used by any architecture.
The vast bulk of this patch is a literal move, the rest is adjusting
the various Makefiles to use dtc and libfdt correctly from their new
locations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some U-Boot versions incorrectly set the number of chipselects to two
for Sequoia/Rainier boards while they only have one chipselect hardwired.
This patch adds a workaround for this, hardcoding the number of chipselects
to one for sequioa/rainer board models and reading the actual value from
the memory controller register DDR0_10 otherwise.
It also fixes another error in the way ibm4xx_denali_fixup_memsize
calculates memory size. When testing the DDR_REDUC bit, the polarity is
backwards. A "1" implies 32-bit wide memory while a "0" implies 64-bit
wide memory.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For enet2 and enet3 the wrong phy-handles have been used in DTS files
of the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 0f73a449a6 added I2C device nodes
for the LM75 thermal sensor on the TQM85xx modules, unfortunately with
the wrong I2C address. The LM75s are located at address 0x48.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device_type "soc" is still required for MPC85xx boards.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add gpio-controller node to manage QE GPIO Bank D;
- Add mmc-spi node;
- Modify board file so that it won't use legacy SPI support with the new
device trees.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older devices tree's used "fsl,85.." instead of the preferred
"fsl,mpc85.." for the memory controller & l2 cache controller nodes.
The EDAC code is the only use of these and has been updated for some
time to support both "fsl,85.." and "fsl,mpc85.."
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.
The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.
For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:
can@3,100 {
compatible = "philips,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 2>;
interrupts = <2 8 1>; // number, type, routing
interrupt-parent = <&fpga_pic>;
};
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The gianfar@25000 node was missing its ranges prop for the mdio bus
and provided an explicit ranges property on gianfar@24000 to match
change from commit:
commit 70b3adbba0
Author: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Thu Mar 19 21:01:45 2009 +0300
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pmc nodes to the device tree files so that the boards
will able to use standby capability of MPC837x processors. The MPC837x
PMC controllers are compatible with MPC8349 ones (i.e. no deep sleep).
sleep = <> properties are used to specify SCCR masks as described
in "Specifying Device Power Management Information (sleep property)"
chapter in Documentation/powerpc/booting-without-of.txt.
Since I2C1 and eSDHC controllers share the same clock source, they
are now placed under sleep-nexus nodes.
A processor is able to wakeup the boards on LAN events (Wake-On-Lan),
console events (with no_console_suspend kernel command line), GPIO
events and external IRQs (IRQ1 and IRQ2).
The processor can also wakeup the boards by the fourth general purpose
timer in GTM1 block, but the GTM wakeup support isn't yet implemented
(it's tested to work, but it's unclear how can we use the quite short
GTM timers, and how do we want to expose the GTM to userspace).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the PPC9A VME Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's PPC9A, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fixed-head.o must be linked into the bootwrapper for raw-binary images to
work. This patch adds it into the bootwrapper.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Eddie Dawydiuk <eddie@embeddedarm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI irqs for the protected sources where not correct for PCI PHBs
Signed-off-by: Ted Peters <ted.peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The registers for the local bus are incorrectly set to 0xf8005000 rather
than there actual location of 0xfef05000.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Serial Synchronous Interface (SSI) is an audio device present on
some Freescale SOCs. Various implementations of the SSI have a different
transmit and receive FIFO depth, but are otherwise identical. To support
these variations, add a new property fsl,fifo-depth to the SSI node that
specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch updates the Xilinx ML507 device tree to match the released
ML507 powerpc reference design (ml507_ppc440_emb_ref). This patch is
needed to boot Linux on the ML507 powerpc reference design without
manually generating and tweaking a device tree from the project directory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On digsy MTC PSC4 and PSC5 should be configured as UART, not PSC3 and PSC4.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for AMCC ppc4xx security device driver. This is the
initial release that includes the driver framework with AES and SHA1 algorithms
support.
The remaining algorithms will be released in the near future.
Signed-off-by: James Hsiao <jhsiao@amcc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds the device-tree entries for a handful of devices on the
Canyonlands board, such as the EHCI and OHCI controllers, the real
time clock and the AD7414 thermal monitor.
I also updated the defconfig to enable various options related to
these devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added a device tree that should be identical to mpc8572ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the bootwrapper for the cuImage target and a compatible property
check for "pnpPNP,501" to the generic serial console support code.
The default link address for the cuImage target is set to 0x800000. This
allows to boot the kernel with AmigaOS4's second level bootloader, which
always loads a uImage at 0x500000.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This device tree does not provide the correct CPU name, as various CPU
models and revisions are used in AmigaOnes. Also the PCI root node does
not contain a interrupt mapping property, as all boards have different
interrupt routing. However the kernel can do a 1:1 mapping of all PCI
interrupts, as only i8259 legacy interrupts are used.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simply add appropriate sdhci nodes.
Note that U-Boot should configure pin multiplexing for eSDHC prior
to Linux could use it. U-Boot should also fill-in the clock-frequency
property (eSDHC clock depends on board-specific SCCR[ESDHCCM] bits).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- sdhc node renamed to sdhci ("sdhc" name is confusing since SDHC is
used to name Secure Digital High Capacity cards, while SDHCI is an
interface).
- Get rid of "fsl,esdhc" compatible entry, it's replaced by the
"fsl,<chip>-esdhc" scheme;
- Get rid of `model' property.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Automatic I2C device probing is not done any more. Therefore we need
proper DTS device node definitions for the I2C LM75 thermal sensor on
the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
Anton Vorontsov