usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCIe MSI interrupts are missing from the device tree source, and
thus were not enabled. This patch adds them.
Tested to work on MPC8315E-RDB with custom FPGA PCIe device.
Signed-off-by: Leon Woestenberg <leon@sidebranch.com>
Tested-by: Leon Woestenberg <leon@sidebranch.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mappings for temperature sensors (adt7461 and lm92) are missing from the
SBC610's DTS file.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of commit 404614728f ("Update FSL
esdhc binding"), we use "fsl,esdhc" compatible entry as a base
match. U-Boot will use the same compatible to fixup esdhc nodes.
This patch updates 83xx dts files so that they conform to the new
bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current device tree for the MPC8272ADS assumes a mapping of 32 MB
of NOR flash at 0xFE00.0000, while there are actually only 8 MB on
the boards, mapped at 0xFF80.0000. When booting an uImage with such a
device tree, the kernel crashes because 0xFE00.0000 is not mapped.
Also introduce aliases for serial[01] and ethernet[01].
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If anything goes wrong when copying images into the install path, then
the install script should exit with an error code so that 'make' knows
about it and tells the user.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As subject says, add dts files for Xilinx ML510 reference design with
the PCI host bridge device.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that the 4xx NAND driver is available again in arch/powerpc, let's
enable it on Sequoia. This patch also disables the early debug messages
(CONFIG_PPC_EARLY_DEBUG) in the Sequoia defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.
One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.
The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary. By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For serial flash support we need to:
- Add QE Par IO Bank E device tree node, a GPIO from this bank is
used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").
Also add node for NAND support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level. It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
The mktree utility defines some variables as "uint", although this is not a
standard C type, and so cross-compiling on Mac OS X fails. Change this to
"unsigned int".
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc kernel always requires an Open Firmware like device tree
to supply device information. On systems without OF, this comes from
a flattened device tree blob. This blob is usually generated by dtc,
a tool which compiles a text description of the device tree into the
flattened format used by the kernel. Sometimes, the bootwrapper makes
small changes to the pre-compiled device tree blob (e.g. filling in
the size of RAM). To do this it uses the libfdt library.
Because these are only used on powerpc, the code for both these tools
is included under arch/powerpc/boot (these were imported and are
periodically updated from the upstream dtc tree).
However, the microblaze architecture, currently being prepared for
merging to mainline also uses dtc to produce device tree blobs. A few
other archs have also mentioned some interest in using dtc.
Therefore, this patch moves dtc and libfdt from arch/powerpc into
scripts, where it can be used by any architecture.
The vast bulk of this patch is a literal move, the rest is adjusting
the various Makefiles to use dtc and libfdt correctly from their new
locations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some U-Boot versions incorrectly set the number of chipselects to two
for Sequoia/Rainier boards while they only have one chipselect hardwired.
This patch adds a workaround for this, hardcoding the number of chipselects
to one for sequioa/rainer board models and reading the actual value from
the memory controller register DDR0_10 otherwise.
It also fixes another error in the way ibm4xx_denali_fixup_memsize
calculates memory size. When testing the DDR_REDUC bit, the polarity is
backwards. A "1" implies 32-bit wide memory while a "0" implies 64-bit
wide memory.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For enet2 and enet3 the wrong phy-handles have been used in DTS files
of the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 0f73a449a6 added I2C device nodes
for the LM75 thermal sensor on the TQM85xx modules, unfortunately with
the wrong I2C address. The LM75s are located at address 0x48.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device_type "soc" is still required for MPC85xx boards.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add gpio-controller node to manage QE GPIO Bank D;
- Add mmc-spi node;
- Modify board file so that it won't use legacy SPI support with the new
device trees.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older devices tree's used "fsl,85.." instead of the preferred
"fsl,mpc85.." for the memory controller & l2 cache controller nodes.
The EDAC code is the only use of these and has been updated for some
time to support both "fsl,85.." and "fsl,mpc85.."
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.
The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.
For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:
can@3,100 {
compatible = "philips,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 2>;
interrupts = <2 8 1>; // number, type, routing
interrupt-parent = <&fpga_pic>;
};
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The gianfar@25000 node was missing its ranges prop for the mdio bus
and provided an explicit ranges property on gianfar@24000 to match
change from commit:
commit 70b3adbba0
Author: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Thu Mar 19 21:01:45 2009 +0300
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pmc nodes to the device tree files so that the boards
will able to use standby capability of MPC837x processors. The MPC837x
PMC controllers are compatible with MPC8349 ones (i.e. no deep sleep).
sleep = <> properties are used to specify SCCR masks as described
in "Specifying Device Power Management Information (sleep property)"
chapter in Documentation/powerpc/booting-without-of.txt.
Since I2C1 and eSDHC controllers share the same clock source, they
are now placed under sleep-nexus nodes.
A processor is able to wakeup the boards on LAN events (Wake-On-Lan),
console events (with no_console_suspend kernel command line), GPIO
events and external IRQs (IRQ1 and IRQ2).
The processor can also wakeup the boards by the fourth general purpose
timer in GTM1 block, but the GTM wakeup support isn't yet implemented
(it's tested to work, but it's unclear how can we use the quite short
GTM timers, and how do we want to expose the GTM to userspace).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the PPC9A VME Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's PPC9A, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fixed-head.o must be linked into the bootwrapper for raw-binary images to
work. This patch adds it into the bootwrapper.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Eddie Dawydiuk <eddie@embeddedarm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI irqs for the protected sources where not correct for PCI PHBs
Signed-off-by: Ted Peters <ted.peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The registers for the local bus are incorrectly set to 0xf8005000 rather
than there actual location of 0xfef05000.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Serial Synchronous Interface (SSI) is an audio device present on
some Freescale SOCs. Various implementations of the SSI have a different
transmit and receive FIFO depth, but are otherwise identical. To support
these variations, add a new property fsl,fifo-depth to the SSI node that
specifies the depth of the FIFOs.
Also update the MPC8610 HPCD device tree with this property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch updates the Xilinx ML507 device tree to match the released
ML507 powerpc reference design (ml507_ppc440_emb_ref). This patch is
needed to boot Linux on the ML507 powerpc reference design without
manually generating and tweaking a device tree from the project directory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On digsy MTC PSC4 and PSC5 should be configured as UART, not PSC3 and PSC4.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for AMCC ppc4xx security device driver. This is the
initial release that includes the driver framework with AES and SHA1 algorithms
support.
The remaining algorithms will be released in the near future.
Signed-off-by: James Hsiao <jhsiao@amcc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds the device-tree entries for a handful of devices on the
Canyonlands board, such as the EHCI and OHCI controllers, the real
time clock and the AD7414 thermal monitor.
I also updated the defconfig to enable various options related to
these devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added a device tree that should be identical to mpc8572ds.dtb except
the physical addresses for all IO are above the 4G boundary.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the bootwrapper for the cuImage target and a compatible property
check for "pnpPNP,501" to the generic serial console support code.
The default link address for the cuImage target is set to 0x800000. This
allows to boot the kernel with AmigaOS4's second level bootloader, which
always loads a uImage at 0x500000.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This device tree does not provide the correct CPU name, as various CPU
models and revisions are used in AmigaOnes. Also the PCI root node does
not contain a interrupt mapping property, as all boards have different
interrupt routing. However the kernel can do a 1:1 mapping of all PCI
interrupts, as only i8259 legacy interrupts are used.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simply add appropriate sdhci nodes.
Note that U-Boot should configure pin multiplexing for eSDHC prior
to Linux could use it. U-Boot should also fill-in the clock-frequency
property (eSDHC clock depends on board-specific SCCR[ESDHCCM] bits).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- sdhc node renamed to sdhci ("sdhc" name is confusing since SDHC is
used to name Secure Digital High Capacity cards, while SDHCI is an
interface).
- Get rid of "fsl,esdhc" compatible entry, it's replaced by the
"fsl,<chip>-esdhc" scheme;
- Get rid of `model' property.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Automatic I2C device probing is not done any more. Therefore we need
proper DTS device node definitions for the I2C LM75 thermal sensor on
the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix misspelling of "firmware" in powerpc Makefile
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The newest revision of uboot reworks the memory map for this
board to look more like the 85xx boards. Also, some regions
which were far larger than the actual hardware have been scaled
back to match the board, and the imaginary second flash bank has
been removed. Rapidio and PCI are mutually exclusive in the hardware,
and they now are occupying the same space in the address map.
The Rapidio node is commented out of the .dts since PCI is the
common use case.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add the usb node to support USB host on the MPC8360E-RDK
boards.
Currently U-Boot doesn't fill the clock-frequency property for
timer nodes, so for now we have to fill it manually.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The correct #address-cells was still used for the actual translation,
so the impact is only a possibility of choosing the wrong range entry
or failing to find any match. Most common cases were not affected.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the localbus reg & range properties to respect that the top
level #address-cells and #size-cells = 2. The original commit
(c64ef80b51) did not do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch the L2 cache is enabled on Canyonlands to increase the
overall performance. There is a known cache coherency issue with the L2
cache, but this is related to the high bandwidth (HB) PLB segment where
the memory address is 0x8.xxxx.xxxx (low bandwidth PLB segment is mapped
to 0x0.xxxx.xxxx). Since this HB address is currently unused it is safe
to enable the L2 cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The cuboot-acadia.c wrapper can cause assembler errors on some
toolchains due to the lack of the proper BOOTCFLAGS. This adds
the proper flags for the file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch creates the dts files for each core and splits the devices
between the two cores for MPC8572DS.
core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1.
core1 has L2, dma2, eth2, eth3, pci2, msi.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add NOR and NAND flash partitions for mpc8572ds board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic support for the GPIO available on the SBC610 VPX Single Board Computer
from GE Fanuc (PowerPC MPC8641D).
This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO
functionality is exposed through the AFIX pins on the backplane, unless used
by an AFIX card.
This code currently does not support switching between totem-pole and
open-drain outputs (when used as outputs, GPIOs default to totem-pole).
The interrupt capabilites of the GPIO lines is also not currently supported.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch corrects the bus-frequency value provided in the SBC610's dts.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
David Gibson suggested that since we are now unconditionally copying
the dtb into a malloc()ed buffer, it would be sensible to add a little
padding to the buffer at that point, so that further device tree
manipulations won't need to reallocate it.
This implements that suggestion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 91a0030295, plus
commit 0dcd440120 ("powerpc: Revert CHRP
boot wrapper to real-base = 12MB on 32-bit") which depended on it.
Commit 91a00302 was causing NVRAM corruption on some pSeries machines,
for as-yet unknown reasons, so this reverts it until the cause is
identified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450d ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms have variants that can share most of a flat device tree but need
a few devices selectively pruned at boot time. This adds del_node() to ops.h
to allow access to the existing fdt_del_node().
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8572ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the bogus device_type usage.
The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.
Boards should specify proper compatible entries instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by addnote to the zImage from
12MB to 32MB. It turns out that this causes unnecessary extra reboots
on old 32-bit CHRP machines. This therefore adds a -r flag to addnote
to allow us to specify what real-base value it should put in the CHRP
note, and adjusts the wrapper script to pass -r c00000 to addnote when
making a zImage for a CHRP machine. Also, CHRP machines ignore the
RPA note, so we don't need to arrange for it to be the same as the
kernel's.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This target is needed to build cuImages with an embedded ramdisk image.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes. It should return zero.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board. The
clocking code is derived from U-Boot, originally written by Stefan Roese.
Signed-off-by: Josh Boyer <jwboyer@linux.ibm.com>
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Current device trees do not have the device_type = soc property set
anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound
drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use. We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree. These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use. Also update the
ssi.txt documentation.
These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cc, "[POWERPC]
bootwrapper: Build multiple cuImages"). When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.
This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.
Also enable MTD support in the defconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set. This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations. (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)
The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run. In fact we call it twice; once before calling prom_init, and again
when starting the main kernel. This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.
This also changes __va and __pa to use an equivalent definition that is
simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).
With this, relocatable kernels still copy themselves down to physical
address 0 and run there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the AD7414 temperature sensor
on Sequoia PPC440EPx board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A make -j20 powerpc kernel build broke a couple of months ago saying:
In file included from arch/powerpc/boot/gunzip_util.h:13,
from arch/powerpc/boot/prpmc2800.c:21:
arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token
arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’
arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token
It happened again yesterday: too rare for me to confirm the fix, but
it looks like the list of dependants on gunzip_util.h was incomplete.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file. Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes the following build error with mpc866_ads_defconfig:
<-- snip -->
...
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to the missing compatible property for the SOC, the MPC I2C buses are
not found any more. This patch fixes this issue. Furthermore it corrects
the name of the SOC node and adds the missing I2C node for the RTC.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we coverted the .dts to v1 we lost a space between the irq
and its polarity/sense information. This causes a bit of chaos
as the reset of the blob is off by one cell.
This was noticed by booting and getting errors w/ATA due to
lock of interrupts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some time ago, a copies of the upstream dtc and libfdt sources were
included in the kernel tree to avoid having these as external
dependencies for building the kernel. Since then development on the
upstream dtc and libfdt has continued. This updates the in-kernel
versions to match the recently released upstream dtc version 1.2.0.
This includes a number of bugfixes, many cleanups and a few new
features.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove include/linux/harrier_defs.h
powerpc: Do not ignore arch/powerpc/include
powerpc: Delete completed "ppc removal" task from feature removal file
powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
powerpc/pci: Don't keep ISA memory hole resources in the tree
powerpc: Zero fill the return values of rtas argument buffer
powerpc/4xx: Update defconfig files for 2.6.27-rc1
powerpc/44x: Incorrect NOR offset in Warp DTS
powerpc/44x: Warp DTS changes for board updates
powerpc/4xx: Cleanup Warp for i2c driver changes.
powerpc/44x: Adjust warp-nand resource end address
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For C code spaces versus tabs is just a religious issue,
but for Makefiles it actually matters.
This patch fixes he following errors:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator. Stop.
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator. Stop.
Since this was inside an ifdef DTC_GENPARSER it was not a problem unless
someone wanted to regenerate the shipped generated files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have. We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.
Also remove the old, redundant chosen node. Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it. Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Korsgaard