Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Current device trees do not have the device_type = soc property set
anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound
drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use. We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree. These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use. Also update the
ssi.txt documentation.
These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cc, "[POWERPC]
bootwrapper: Build multiple cuImages"). When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.
This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.
Also enable MTD support in the defconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set. This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations. (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)
The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run. In fact we call it twice; once before calling prom_init, and again
when starting the main kernel. This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.
This also changes __va and __pa to use an equivalent definition that is
simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).
With this, relocatable kernels still copy themselves down to physical
address 0 and run there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the AD7414 temperature sensor
on Sequoia PPC440EPx board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A make -j20 powerpc kernel build broke a couple of months ago saying:
In file included from arch/powerpc/boot/gunzip_util.h:13,
from arch/powerpc/boot/prpmc2800.c:21:
arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token
arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’
arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token
It happened again yesterday: too rare for me to confirm the fix, but
it looks like the list of dependants on gunzip_util.h was incomplete.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the Yosemite board to the explicitly supported list for ppc44x_simple
boards and remove the compatible entry for bamboo from the DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add explicit support for the AMCC Glacier eval board to Kconfig and the
ppc44x_simple file. Also removes the cayonlands compatible entry from the
DTS file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes the following build error with mpc866_ads_defconfig:
<-- snip -->
...
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to the missing compatible property for the SOC, the MPC I2C buses are
not found any more. This patch fixes this issue. Furthermore it corrects
the name of the SOC node and adds the missing I2C node for the RTC.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we coverted the .dts to v1 we lost a space between the irq
and its polarity/sense information. This causes a bit of chaos
as the reset of the blob is off by one cell.
This was noticed by booting and getting errors w/ATA due to
lock of interrupts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some time ago, a copies of the upstream dtc and libfdt sources were
included in the kernel tree to avoid having these as external
dependencies for building the kernel. Since then development on the
upstream dtc and libfdt has continued. This updates the in-kernel
versions to match the recently released upstream dtc version 1.2.0.
This includes a number of bugfixes, many cleanups and a few new
features.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove include/linux/harrier_defs.h
powerpc: Do not ignore arch/powerpc/include
powerpc: Delete completed "ppc removal" task from feature removal file
powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
powerpc/pci: Don't keep ISA memory hole resources in the tree
powerpc: Zero fill the return values of rtas argument buffer
powerpc/4xx: Update defconfig files for 2.6.27-rc1
powerpc/44x: Incorrect NOR offset in Warp DTS
powerpc/44x: Warp DTS changes for board updates
powerpc/4xx: Cleanup Warp for i2c driver changes.
powerpc/44x: Adjust warp-nand resource end address
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For C code spaces versus tabs is just a religious issue,
but for Makefiles it actually matters.
This patch fixes he following errors:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator. Stop.
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator. Stop.
Since this was inside an ifdef DTC_GENPARSER it was not a problem unless
someone wanted to regenerate the shipped generated files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have. We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.
Also remove the old, redundant chosen node. Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it. Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current device tree is only bare bones. This patch adds nodes to make
it a complete tree for the MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is inconvenient to add additional default targets to the bootwrapper
Makefile for each new board supported which just needs a different dts
file. This change allows the defconfig to specify additional build
targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.
As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.
The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.
This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.
The code has further been reworked where appropriate to use those macros
and inlines.
In addition, the register size passed to ioremap is now taken from the
device tree:
c4 for EMAC4SYNC cores
74 for EMAC4 cores
70 for EMAC cores
rather than sizeof (emac_regs).
Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.
This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The wrapper script is missing the bits needed for building generic
simpleImage targets (targets which don't depend on any particular
firmware interface and retrieve all their data from the device tree).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware. Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.
The wrapper was also modified to add the 440 build.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This new file adds support for the ML507 reference design. The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change to the makefile corrects the build of a simpleImage with initrd.
Signed-off-by: John Linn <john.linn@xilinx>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since most bootloaders or wrappers tend to update or add some information
to the .dtb they a handled they need some working space to do that in.
By default add 1K of padding via a default setting of DTS_FLAGS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we set the start of the .text section to be 4Mb for pSeries.
In situations where the zImage is > 8Mb we'll fail to boot (due to
overlapping with OF). Move .text in a zImage from 4MB to 64MB
(well past OF).
We still will not be able to load large zImage unless we also move OF,
to that end, add a note to the zImage ELF to move OF to 32Mb. If this
is the very first kernel booted then we'll need to move OF manually by
setting real-base.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GCC 4.4.x looks to be adding support for generating out-of-line register
saves/restores based on:
http://gcc.gnu.org/ml/gcc-patches/2008-04/msg01678.html
This breaks the bootwrapper as we'd need to link with libgcc to get the
implementation of the register save/restores.
To workaround this issue, we just stole the save/restore code from gcc
and simplified it down for our needs (integer only).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the sam440ep.dts dts-v1 compliant.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds local bus nodes for Flash and CAN to the DTS file
of the TQM8560 module (tqm8560.dts).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash
memory and therefore a modified memory map is required and setup by
the board loader. This patch adds an appropriate DTS file.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andrew Klossner pointed out the IO space size was in violation of
the alignment requirements for windows on the 85xx. The size should
have been 1M (to match u-boot).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 2 of 5: support for the board in arch/powerpc/boot.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 1 of 5: DTS file describing the board peripherals. As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects the names of two CONFIG_ variables.
Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:
<-- snip -->
...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0 /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec. Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere. Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This fixes the PCI node in the Rainier to match the spec from AMCC. A
similar fix was done for 440EPx, which shares the same values as 440GRx.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
At the moment we have a mixture of left-over version 0 and new-format
version 1 files in arch/powerpc/boot/dts. This is potentially
confusing to people new to the dts format attempting to figure it out.
So, this patch converts all the as-yet unconverted dts v0 files and
converts them to v1. They're mechanically-converted, and not hand
tweaked so in some cases they're not 100% in keeping with usual v1
style, but the convertor program does have some heuristics so the
discrepancies aren't too bad.
I have checked that this patch produces no changes to the resulting
dtb binaries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
dtbImage.* and several zImage. targets get created but never cleaned up.
Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary. Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.
This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it. The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.
That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virtex405-head.S is an assembler file, not a C file; therefore BOOTAFLAGS
is the correct place to set the needed -mcpu=405 flag.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based adressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the ns16550 driver to use the reg-offset property
so that the Xilinx UART 16550 can be used with it. The reg-shift
was already being handled.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts. The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.
2. The inbound memory mask calculation was wrong.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch modifies the Embedded Planet EP8248E device tree to reference the
SMC paramater RAM base register instead of the parameter RAM allocated by the
boot loader.
The cpm_uart driver will allocate parameter RAM itself, making the serial port
initialisation independent of the boot loader.
The patch adds the parameter RAM allocated by the boot loader in the CPM muram
node, making it available to the kernel.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch relocates the buffer descriptors and the SMC parameter RAM at the
end of the first CPM muram chunk, as described in the device tree. This allows
device trees to stop excluding SMC parameter ram allocated by the boot loader
from the CPM muram node.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a new generic device tree processing function that retrieves
virtual reg addresses from the device tree to the bootwrapper code. It also
updates the bootwrapper code to use the new function.
dt_get_virtual_reg() retrieves the virtual reg addresses from the
"virtual-reg" property. If the property can't be found, it uses the "reg"
property and walks the tree to translate it to absolute addresses.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages. Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.
We use objdump to extract the PHDR. We assume that there is only one
PHDR in the vmlinux of type LOAD.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file. Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform. Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank. This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports. The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device. The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller". Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated. This fixes them. Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:
- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
(the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.
Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Improve the debugging support of the PS3 bootwraper code:
o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
allow for more debugging code in the overlay.
o Use the dot symbol to set the size of __system_reset_overlay. The
assembler will then emit an error if the overlay code is too big.
o Remove some unused instructions.
o Update the text describing the PS3 bootwrapper overlay.
o Add a check for null pointer writes.
o Change hcall return value from s64.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b9588592
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This dts source file for the AMCC 460EX Canyonlands evalutaion board
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.
The now obsolete linux,network-index properties are removed from the
corresponding device trees. This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.
The references to linux,network-index are removed from
booting-without-of.txt. Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree. By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pattern substitution rules were failing when used with zImage-dtb
targets. If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.
This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases. This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html
Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct the remaining 44x cuboot wrappers to define TARGET_4xx as well. This
creates the correct structure to use, including things like the second MAC
address.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
In order to get the proper boad info (bd_info) structure defined in ppcboot.h
both TARGET_4xx and TARGET_44x should be defined for all PowerPC 440 boards.
The 440GX boards also need TARGET_440GX defined since they have 4 EMACs and
there are 4 MAC addesses in bd_info passed by u-boot.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch changes the katmai (440SPe) L1 cache size to 32k. Some
whitespace issues are cleaned up too.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the 4xx PCIe driver checks for 405ex compatibility, the
PCIe interface was not detected as it is currently defined as
"405exr" compatible. This patch changes it to "405ex".
The 405EX and 405EXr are identical exept that the 2nd PCIe and the
2nd EMAC interfaces are missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
GCC versions before 3.4 did not support the -mcpu=440 option. Use
-mcpu=405 for the 4xx specific bootwrapper files, as that has been
around for much longer.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove all "i2c" and "xxmii-interface" (rgmii etc) device_type entries
from the 4xx dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix a bug in the lv1_get_repository_node_value() routine of the PS3
bootwrapper. Changes in the PS3 system firmware 2.20 cause this bug
to hang the system when branching from the bootwrapper to the kernel
_start.
Since the video system has not yet been enabled at the time
the bug is hit, the system hangs with a blank screen. Earlier
firmwares don't cause such a catastrophic failure, and so this
bug went undetected.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
with a fdt blob which means for any given configuration only one dts
file can be selected and so support for only one board can be built
This moves the selection of the default .dts file out of the kernel
config and into the bootwrapper makefile. The makefile chooses which
images to build based on the kernel config and the dts source file
name is taken directly from the image name. For example "cuImage.ebony"
will use "ebony.dts" as the device tree source file.
In addition, this patch allows a specific image to be requested from the
command line by adding "cuImage.%" and "treeImage.%" targets to the list
of valid built targets in arch/powerpc/Makefile. This allows the default
dts selection to be overridden.
Another advantage to this change is it allows a single defconfig to be
supplied for all boards using the same chip family and only differing in
the device tree.
Important note: This patch adds two new zImage targets; zImage.dtb.% and
zImage.dtb.initrd.% for zImages with embedded dtb files. Currently
there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc,
adder875-redboot and ep8248e. This patch *changes the zImage filenames*
for those platforms. ie. 'zImage.ps3' is now 'zImage.dtb.ps3'.
This new zImage.dtb targets were added so that the .dts file could be
part of the dependancies list for building them.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minimal /dts-v1/ device tree for mpc5121 ads.
port-number property in uart nodes
will go away after the driver learns to use aliases
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cleaned up IRQ layout and removed unsused ISU allocations.
Fixed RTC address typo from /dts-v1/ conversion.
Incorporated list suggestions to use an "iomega," vendor prefix,
and to use a node reference rather than a hard path.
Signed-off-by: Jon Loeliger <jdl@@jdl.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
cpm_uart_core has a dependency on fsl,cpm-brg/clock-frequency, this
means that a .dts that uses the cpm uart driver needs to supply a
clock-frequency entry for get_brgfreq to return a meaningful number.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8313 rdb has a ds1339 at address 0x68.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to the 8349EA ref man, the second PCI PHB IRQ is 67. Thanks to Peter
Van Ackeren for finding this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.
The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e. the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.
The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.
I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently there are several dts that don't specify address or size
cells for the muram. This causes dtc to use default values, one of
which is an address-cells of two, and this breaks the parsing of the
muram ranges, which is assuming an address-cells of one. For example:
Warning (reg_format): "reg" property in
/qe@e0100000/muram@10000/data-only@0 has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 1)
Explicitly setting the address and size cells gets it parsed properly
and gets rid of the four dtc warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts files for the MPC838xE Reference Development Board (RDB).
The board is a mini-ITX reference board with 256M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
the difference among the three files is the 8377 has two, the 8378
none, and the 8379 has four sata controllers.
partially based on the 8379 mds device trees.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts for the MPC8315E Reference Development Board (RDB).
The board is a mini-ITX reference board with 128M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
device_type property is bogus, thus use proper compatible.
Also change compatible property to "fsl,ucc-mdio".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move mpc834x_mds device tree source forward to dts-v1 format. Nothing
too complex in this one, so it boils down to just adding a bunch of 0x
in the right places and converting clock speeds to decimal.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the device tree source for the Wind River SBC834x board.
It is based on the MPC834x_MDS DTS, with the biggest difference being
the lack of BCSR and the PCI2 that the MDS gets via the PIB. That,
and this file is also dts-v1 format.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8548 board.
The biggest difference between this and the MPC8548CDS reference
platform is the absence of the CDS's Arcadia peripherals and physical
access to the PCI#2 bus.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8560 board. The
biggest difference between this and the MPC8560ADS reference platform
dts is the use of an external 16550 compatible UART instead of the CPM2.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to find a device node by just what its compatible with.
This is useful in cases that we don't have a prop to find the node with.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The various 5200 dts files don't have values specified for the soc
node, which in turn results in a warning from the processing of
every child node (roughly 40 warnings per file). This explicitly
sets the default values and gets rid of all the warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the cuboot wrapper for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the device tree for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds the Haleakala dts. The Haleakala is a stripped down
version of the Kilauea (405EX) with only one EMAC and only one PCIe
interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Based on the Kurobox DTS files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts
Also add compatible field for the soc node, so that it will be picked up
by of_platform_bus_probe().
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node. Update
the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library
to support slow UCC devices and modules.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI based boards had the interrupt maps for USB on the ULI incorrectly
set.
Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe
controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to set the mac address given the alias for the device.
Removes the need for having a linux,network-index property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for Promess Motion-PRO board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for CM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for TQ Components TQM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update .gitignore as needed by dtc addition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Missed this one in the boot loader before.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for 405GPr processors with optional
new mode strapping. ibm405gp_fixup_clocks() can now be used
for 405GP and 405GPr CPUs.
This is in preparation of porting the cpci405 platform support
from arch/ppc to arch/powerpc.
This patch also adds ibm405ep_fixup_clocks() to support
405EP CPUs from the boot wrapper.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Recent DTC versions disallow certain special characters in full paths without
being quoted with {}. That however breaks compatibility with older DTC
versions. Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Josh Boyer