When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire V5 with the ALC282 codec is given the wrong value for the
0x19 PIN by the laptop's BIOS. Overriding it with the correct value
adds support for the headset microphone which would not otherwise be
visible in the system.
The fix is based on commit 7819717b11 with a similar quirk for Acer
Aspire with the ALC269 codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Mateusz Sylwestrzak <matisec7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two small fixes for HD-audio and USB LINE6, and the rest are
a few new quirks and device ID addition that are good enough to get
into 4.2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EgRm
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are two small fixes for HD-audio and USB LINE6, and the rest are
a few new quirks and device ID addition that are good enough to get
into 4.2"
* tag 'sound-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable HP amp and mute LED on HP Folio 9480m [v3]
ALSA: line6: Fix -EBUSY error during active monitoring
ALSA: hda - Fix a wrong busy check in alt PCM open
ALSA: hda - add codec ID for Broxton display audio codec
ALSA: usb-audio: Add MIDI support for Steinberg MI2/MI4
In kstrdup we should return -ENOMEM when it reports an
memory allocation failure, while the -ENODEV is referred
to a failure in finding the cpu node in the device tree.
Signed-off-by: Heloise NH <kernelpatch_update@163.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop needs GPIO4 pulled high to enable the headphone amplifier,
and has a mute LED on GPIO3. I modelled the patch on the existing
GPIO4 code which pulls the line low for the same purpose; this time,
the HP amp line is pulled high.
v2: Disable the headphone amplifier when no headphone is connected.
Don't disable power savings to preserve the LED state.
v3: Remove headset-specific hooks and code; this is just a headphone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the alt PCM open callback returns -EBUSY when an
independent HP is turned off, supposing that it conflicts with the
main PCM. However, obviously, this check is wrong when the
independent HP itself isn't enabled but the alt PCM was explicitly
created via alc_dac_nid by a codec driver.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x8086280a) and module alias for Broxton
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DOli
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups"
* tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Fix uninintialized error return
ALSA: hda: Delete an unnecessary check before the function call "snd_info_free_entry"
ALSA: hda - Add a fixup for Dell E7450
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780
ALSA: hda - Add headset support to Acer Aspire V5
ALSA: hda - restore the MIC FIXUP for some Dell machines
ALSA: jack: Fix endless loop at unique index detection
ALSA: hda - set proper caps for newer AMD hda audio in KB/KV
ALSA: hda - Disable widget power-save for VIA codecs
ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
The snd_info_free_entry() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
The fix is to ignore the non-HP sequencer checks.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Those FIXUPs were applied to the machines through pin quirks, but
recently the PCI_QUIRK makes them can't apply to the machines.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99851
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget power-save that was enabled in 4.1 kernel seems resulting
in the silent output on VIA codecs by some reason. Some widgets get
wrong power states.
As a quick fix, turn this flag off while keeping power_down_unused
flag. This will bring back to the state of 4.0.x.
Fixes: 688b12cc3c ('ALSA: hda - Use the new power control for VIA codecs')
Reported-and-tested-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@vger.kernel.org> # v4.1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thinkpad X250, when attached to a dock, has two headphone outs but
no line out. Make sure we don't try to turn this into one headphone
and one line out (since that disables the headphone amp on the dock).
Alsa-info at http://www.alsa-project.org/db/?f=36f8764e1d782397928feec715d0ef90dfddd4c1
Cc: stable@vger.kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since this is common option for HDA driver to specfiy pre-allocated
buffer, we should make this option availble to all HDA driver by
moving this to HDA core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SND_HDA_I915=n, we get a compile warning:
sound/pci/hda/hda_intel.c: In function ‘azx_probe_continue’:
sound/pci/hda/hda_intel.c:1882:2: warning: label ‘skip_i915’ defined but not used [-Wunused-label]
Fix it by putting again ifdef to it. Sigh.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new Dell XPS13 also requires the similar quirk for fixing the
noisy outputs. (But, as the codec was changed, now the fixup for
Latitude is used instead.)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99851
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We still got a report that the audio crackles and noises occur with
the recent 4.1 kernels on Dell machines. These machines seem to need
similar workarounds that have been applied to the recent Dell XPS 13
models. Since the codec of these machines (Dell Latitute E7240 and
E7440) is different from XPS 13's one, we need a new fixup entry.
Also, it was confirmed that the previous workaround to disable the
widget power-save (commit [219f47e4f964: ALSA: hda - Disable widget
power-saving for ALC292 & co]) is no longer needed after this fix.
So, this patch includes the partial revert of the commit, too.
Reported-and-tested-by: Mihai Donțu <mihai.dontu@gmail.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a HP Envy TouchSmart laptop, there are 2 speakers (main speaker
and subwoofer speaker), 1 headphone and 2 DACs, without this fixup,
the headphone will be assigned to a DAC and the 2 speakers will be
assigned to another DAC, this assignment makes the surround-2.1
channels invalid.
To fix it, here using a DAC/pin preference map to bind the main
speaker to 1 DAC and the subwoofer speaker will be assigned to another
DAC.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous patch tried to continue the probe if i915 binding fails.
For for simplicity reason, we haven't implemented abort even for
controller chips that are dedicated for HDMI/DP on HSW and BDW.
However, Mengdong suggested that this can be dangerous; BIOS may
disable gfx power well although the PCI entry for HD-audio is left,
and this may result in the unexpected behavior, kernel errors, etc.
For avoiding this situation, abort the probe at i915 binding failure
only for HSW/BDW chips selectively. For other chips, it still
continues.
Fixes: bf06848bdb ('ALSA: hda - Continue probing even if i915 binding fails')
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another regression by the transition to regmap cache; for better
usability, we had the fake mute control using the zero amp value for
Conexant codecs, and this was forgotten in the new hda core code.
Since the bits 4-7 are unused for the amp registers (as we follow the
syntax of AMP_GET verb), the bit 4 is now used to indicate the fake
mute. For setting this flag, snd_hda_codec_amp_update() becomes a
function from a simple macro. The bonus is that it gained a proper
function description.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges and resolves the non-trivial conflicts with the recent fix
for hda-i915 binding fallback.
Conflicts:
sound/pci/hda/hda_intel.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently snd-hda-intel driver aborts the probing of Intel HD-audio
controller with i915 power well management when binding with i915
driver via hda_i915_init() fails. This is no big problem for Haswell
and Broadwell where the HD-audio controllers are dedicated to
HDMI/DP, thus i915 link is mandatory. However, Skylake, Baytrail and
Braswell have only one controller and both HDMI/DP and analog codecs
share the same bus. Thus, even if HDMI/DP isn't usable, we should
keep the controller working for other codecs.
For fixing this, this patch simply allows continuing the probing even
if hda_i915_init() call fails. This may leave stale sound components
for HDMI/DP devices that are unbound with graphics. We could abort
the probing selectively, but from the code simplicity POV, it's better
to continue in all cases.
Reported-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable runtime PM of the HDMI audio codec on the latest Intel platforms.
So the HD-A controller or HDMI codec can suspend when idle timeout by
default and release the GFX power well.
The patch influences HSW/BDW/BYT/BSW/SKL. Eariler platforms and third
party analog codecs will not be influenced.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new regmap code seems to cache this, which isn't helpful
for the hotplug dock situation where this gets updated.
Use the uncached query for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the controller flag 'need_i915_power' is
not set to release the display power after probe, and the codec flag
'link_power_control' is set to request/release the display power via
bus link_power ops.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to
make the sound working like other Aspire models.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT202x codecs seem requiring some delay after the resume D0 power
transition for making the jack detection working again. Without the
delay soon after D0, the jack is always detected as unplugged.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98921
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... so that the parser code can overwrite some optional ops. For
Realtek and others, it can be set solely in the spec allocator, so it
results in a good code cleanup, too.
With this change, we can finally remove the local stream_pm setup and
rely on the generic parser's automatic setting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [49fb18972581: ALSA: hda - Set stream_pm ops automatically
by generic parser] resulted in regressions on some Realtek and VIA
codecs because these drivers set patch_ops after calling the generic
parser, thus stream_pm got cleared to NULL again. I haven't noticed
since I tested with IDT codec.
Restore (partial revert) the stream_pm ops for them to fix the
regression.
Fixes: 49fb189725 ('ALSA: hda - Set stream_pm ops automatically by generic parser')
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When headphone mic boost is above zero, some 10 - 20 second delay
might occur before the headphone mic is operational.
Therefore disable the headphone mic boost control (recording gain is
sufficient even without it).
(Note: this patch is not about the headset mic, it's about the less
common mic-in only mode.)
BugLink: https://bugs.launchpad.net/bugs/1454235
Suggested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We may disable proc fs only for sound part, to reduce ALSA
memory footprint. So add CONFIG_SND_PROC_FS and replace the
old CONFIG_PROC_FSs in alsa code.
With sound proc fs disabled, we can save about 9KB memory
size on X86_64 platform.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report that 4.1-rc causes noises on a Dell
laptop. Similar like Realtek codec, this seems also triggered by the
recent power_save_node feature. As this kind of issue is quite hard
to debug without actual hardware, disable the power_save_node flag for
this codec as a workaround.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new AMD controller [1002:aac8] seems to need the quirk for other AMD
NS HDMI stuff, otherwise it gives noisy sounds.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=99021
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows user to test power_save_node feature via sysfs or patch
firmware even on the codecs that don't specify it. It'll also save a
few lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7290006d8c.
Through the regression report, it was revealed that the
tpacpi_led_set() call to thinkpad_acpi helper doesn't only toggle the
mute LED but actually mutes the sound. This is contradiction to the
expectation, and rather confuses user.
According to Henrique, it's not trivial to judge which TP model
behaves "LED-only" and which model does whatever more intrusive, as
Lenovo's implementations vary model by model. So, from the safety
reason, we should revert the patch for now.
Reported-by: Martin Steigerwald <martin@lichtvoll.de>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got reports that ALC3226 (a Dell variant of ALC292) gives click
noises at transition from D3 to D0 when the widget power-saving is
enabled. Further debugging session showed that avoiding it isn't
trivial, unfortunately, since paths are basically activated
dynamically while the pins have been already enabled.
This patch disables the widget power-saving for such codecs.
Reported-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget (node) power-saves restore the widget states at each
transition from D3 to D0 on each node. This was added in the commit
[d545a57c5f84:ALSA: hda - Sync node attributes at resume from widget
power saving]. However, the test was rater false-positive; this
wasn't needed for any codecs.
Since the resync may take significant number of additional verbs to be
executed, it's better to reduce it. Let's disable it for now again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file is moved to hda core and renamed to hdac_i915.c, so can be used
by both legacy HDA driver and new Skylake audio driver.
- Add snd_hdac_ prefix to the public APIs.
- The i915 audio component is moved to core bus and dynamically allocated.
- A static pointer hdac_acomp is used to help bind/unbind callbacks to get
this component, because the sound card's private_data is used by the azx
chip pointer, which is a legacy structure. It could be removed if private
_data changes to some core structure which can be extended to find the
bus.
- snd_hdac_get_display_clk() is added to get the display core clock for
HSW/BDW.
- haswell_set_bclk() is moved to hda_intel.c because it needs to write the
controller registers EM4/EM5, and only legacy HD-A needs it for HSW/BDW.
- Move definition of HSW/BDW-specific registers EM4/EM5 to hda_register.h
and rename them to HSW_EM4/HSW_EM5, because other HD-A controllers have
different layout for the extended mode registers.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modern machines tend to have only one headset jack nowadays, and they
often need these quirks. Let's allow them applicable via model
option for ease of debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds quirks detection to the Creative CA0132 codec, and the
quirk for Alienware 15 (2015).
Some quirks may need different pin configuration, so the relevant
compile-time configuration has been removed.
The pin configuration and related initialization verbs are generated at
runtime instead, in ca0132_config() and ca0132_prepare_verbs().
Signed-off-by: Gabriele Martino <g.martino@gmx.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch creates hda_intel_trace.h to add some pm trace functions
used in hda_intel.c
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does:
1. Rename the hda_intel_trace.h to hda_controller_trace.h as
this trace is used in hda_controller.c
2. Add some trace function for pcm flow.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra210 contains a similar codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra114 contains the same codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra30 contains the same codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When probing, provide accurate error messages to help with debugging
failures.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDMI codec on NVIDIA Tegra SoCs has a feature that doesn't exist on
the MCP or GPU variants. The highest bit in the vendor-defined scratch
registers can be used to trigger an interrupt in the HDMI codec, which
is signalled to the HDMI driver. This can be used to pass information,
such as the HDA format, to the HDMI driver so that it can reconfigure
itself accordingly.
While at it, change the name of the codec to Tegra124 since there are no
other SoCs in the Tegra12x family. There isn't really a Tegra12x family.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is set for the MCP variants of the NVIDIA HDA controller, which the
Tegra variant was derived from. This fixes the following warning at boot
time:
[ 2.486610] tegra-hda 70030000.hda: CORB reset timeout#1, CORBRP = 0
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell create new platform with ALC298 codec.
This patch will enable headset mode for ALC298/ALC3266 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo ThinkPad L450 requires the ALC292_FIXUP_TPT440_DOCK fix in
order to get sound output on the docking stations audio port.
This patch was tested using a ThinkPad L450 (20DSS00B00) using kernel
4.0.3 and a ThinkPad Pro Dock.
Signed-off-by: Ansgar Hegerfeld <linux@hegerfeld.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for Conexant HD Audio codecs
CX20721, CX20722, CX20723 and CX20724.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1454656
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC662 does not need any special verbs to change the jack functionality,
and enables mic in through the headphone jack mode by changing the
direction of the headphone pin node.
BugLink: https://bugs.launchpad.net/bugs/1454235
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This enables the headset microphone on Dell Inspiron 5548,
or at least some variants of it.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1452175
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In SKL, HDMI/DP codec and PCH HD Audio Controller are in different power wells,
so it's necessary to reset display audio codecs when power well on, otherwise
display audio codecs will disappear when resume from low power state.
Reset steps when power on:
enable codec wakeup -> azx_init_chip() -> disable codec wakeup
The callback for codec wakeup enable/disable is in drivers/gpu/drm/i915/.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Building errors reported such as below when 'CONFIG_INPUT=m':
...undefined reference to `input_xxx'...
Here change to enable SND_JACK selectively to fix the issue.
Also remove the config 'SND_HDA_INPUT_JACK' which won't be
used anymore.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fujitsu Lifebook E752 laptop needs a similar quirk done for Lifebook
T731. Otherwise the headphone is always muted.
Reported-and-tested-by: Christian Weber <we_chris@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're providing dummy functions for CONFIG_SND_HDA_i915=n, thus ifdef
can be reduced. (But hda_i915_init() has to be fixed to return zero.)
This automatically fixes a compile warning:
sound/pci/hda/hda_intel.c: In function 'azx_probe_continue':
sound/pci/hda/hda_intel.c:1966:1: warning: label 'i915_power_fail' defined but not used [-Wunused-label]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Baytrail (Valleyview) and Braswell (Cherryview), only the HDMI codec is
in the display power well while the HD-A controller isn't. So the controller
flag 'need_i915_power' is not set to release the display power after probe,
and the codec flag 'link_power_control" is set to request/release the display
power via bus link_power ops.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch can improve power saving for Intel platforms on which only the
display audio codec is in the shared i915 power well:
- Add a flag "need_i915_power" to indicate whether the controller needs the
i915 power well.
- The driver will always request the i915 power when probing the controller
and codecs if AZX_DCAPS_I915_POWERWELL is set (either the controller or a
codec needs this power).
- If the controller needs the i915 power, the power will be held after probe
until the controller is runtime suspended or S3. If the controller doesn't
need the power, the power will be released the after probe, and a codec
that needs the power can request/release the power via bus link_power ops.
Background:
- For Haswell/Broadwell, which has a separate HD-A controller for display audio,
both the controller and the display codec are in the i915 power well.
- For Baytrail/Braswell, the display and analog audio share the same HDA
controller and link, and only the display codec is in the i915 power well.
- For Skylake, the display and analog audio share the same HDA controller but
use separate links. Only the display codec is in the i915 power well. And in
legacy mode we take the two links as one. So it can follow Baytrail/Braswell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements the bus link_power ops to request/release i915 display
power well. It can be used by the display codec which shares this power well
with GPU on Intel platforms.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A flag "link_power_control" is added to indicate whether a codec needs to
control the link power. And a new bus ops link_power() is defined for the
codec to request to enable/disable the link power.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is to check the refcount of audio driver and reduce calling to i915.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jack snd_kcontrols can now be created during snd_jack_new()
or by later calling snd_jack_add_new_kctls().
This patch creates the jacks during the initialisation stage
for both phantom and non phantom jacks.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dont create input devices for phantom jacks.
Here, we extend snd_jack_new() to support phantom jack creating:
pass in a bool param for [non-]phantom flag, and a bool param
initial_jack to indicate whether we need to create a kctl at
this stage.
We can also add a kctl to the jack after its created meaning we
can now integrate the HDA and ASoC jacks.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a static method get_available_index() to
allocate the index of new jack kcontrols and also adds
jack_kctl_name_gen() which is used to ensure compatibility
with jack naming by removing " Jack" from some incorrectly
passed names.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the ALSA jack core registers only input devices for each jack
registered. These jack input devices are not readable by userspace devices
that run as non root. This patch series will implement kctls inside the
core jack part, including kctls creating, status changing report, for both
HD-Audio and ASoC jack. This allows non root userspace to read jack status
and act on it.
This patch adds a new API called snd_jack_add_new_kctl(), which will create
a kcontrol, add it to the card, and also attach it to the jack kctl list.
This patch also initialises the jack kctl list after jack is newed, and
reports kctl status when jack insertion/removal events occur.
snd_jack_new() is updated in the following patches to also support creating
phantom jacks and jack kcontrols. We then remove these duplicated features
from HDA jack and have jack kctls handled by core throughout HDA and ASoC.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Modified-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reveiwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the missing flag to enable "Mute-LED Mode" mixer enum
ctl for Thinkpads that have also the software mute-LED control.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED mode control has the fixed on/off states that are
supposed to remain on/off regardless of the master switch. However,
this doesn't work actually because the vmaster hook is called in the
vmaster code itself.
This patch fixes it by calling the hook indirectly after checking the
mute LED mode.
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell XPS13 produces a click noise at boot up, and Gabriele spotted out
that it's triggered by the initial pin control of the mic (NID 0x19).
This has to be set to Hi-Z Vref while the driver initializes to Vref
80% as a normal mic.
This patch fixes the generic parser code not to override the target
vref if it has been already set by the driver, and adds a proper
initialization of the target vref for this pin in the Realtek driver
side.
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the way to manage the resource release of proc
files: namely, let snd_info_free_entry() freeing the whole children.
This makes it us possible to drop the snd_device_*() management. Then
snd_card_proc_new() becomes merely a wrapper to
snd_info_create_card_entry().
Together with this change, now you need to call snd_info_free_entry()
for a proc entry created via snd_card_proc_new(), while it was freed
via snd_device_free() beforehand.
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Switch default pcbeep path to Line in path.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ALC256 does not have a mixer nid at 0x0b, and there's no
loopback path (the output pins are directly connected to the DACs).
This commit fixes an "num_steps = 0 for NID=0xb (ctl = Beep Playback Volume)"
error (and as a result, problems with amixer/alsamixer).
If there's pcbeep functionality, it certainly isn't controlled by setting an
amp on 0x0b, so disable beep functionality (at least for now).
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1446517
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only Intel Haswell and Broadwell have a separate HD-A controller (PCI device 3)
for display audio, which needs to get 24MHz HD-A link BCLK from the variable
display core clock through vendor specific registers EM4 & EM5. Other platforms
(Baytrail, Braswell and Skylake) don't have this feature.
So this patch checks the PCI device ID of the controller in haswell_set_bclk()
and only sync BCLK for HSW and BDW.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Muting the headphone output pin right before the codec suspension
prevents pop noises when headphones are plugged in (except for a
barely audible click noise).
This solution allows to truly save some power when headphones are
plugged in unlike the previous solution (033b0a7ca9c:
"ALSA: hda - Pop noises fix for XPS13 9333")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function is a bit unusual because it accepts negative values as
"conn_len". It's theoretically possible for both "cache_len" and
"conn_len" to be -ENOSPC and in that case we would oops trying to run
memcmp() on the uninitialized "list" pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Originally hda_bus takes its own ops (hda_bus_ops) to allow different
controller drivers giving individual implementations of PCM
attachment, etc. But this never happened and we finally merged both
codec and controller helper codes. Thus there is no merit to keep the
indirect accesses to functions via hda_bus_ops.
This patch replaces these calls with the direct local function calls
for simplification.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [a551d91473e5: ALSA: hda - Use regmap for command verb
caches, too] introduced a regression due to a typo in the conversion;
the IEC958 status bits of slave digital devices aren't updated
correctly. This patch corrects it.
Fixes: a551d91473 ('ALSA: hda - Use regmap for command verb caches, too')
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I seem to have failed to run the build test properly...
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_dev_free':
sound/pci/hda/hda_tegra.c:310:20: error: 'bus' undeclared (first use in this function)
snd_hdac_bus_exit(bus);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After correcting the fields to point the right members, tracepoints
can be reenabled again for the legacy controller code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because AZX_DCAPS_PM_RUNTIME is always defined as non-zero, the
initial part of the expression can be skipped.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and replace with the existing hda-core helper codes.
This reduces lots of lines, finally.
Since struct hda_bus is now embedded into struct azx,
snd_hda_bus_new() is moved and expanded from hda_codec.c to
hda_controller.c, accordingly. Also private_free bus ops and
private_data field are removed because we no longer need to point azx
object from bus (we can use container_of())
The spin locks are consolidated into the single one, bus->reg_lock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Embed hdac_stream object into azx_dev, and use a few basic helper
functions. The most of helper codes for hdac_stream aren't still used
yet.
Also this commit disables the tracepoints temporarily due to build
problems. It'll be enabled again later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One less redirection again. This also requires the change of the call
order in the toplevel divers. Namely, the bus has to be created at
first before other initializations since the memory allocation ops are
called through bus object now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no much merit to keep the HD-audio codec and controller
helper codes in separate modules any longer. Let's merge them into a
single helper module.
This patch just changes Makefile entries to merge two individual
modules to one. The only code change is the removal of superfluous
MODULE_*() macros in one side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controller helper codes to hda-core library.
The I/O access ops are added to the bus ops. The CORB/RIRB, the basic
attributes like irq# and iomap address, some locks and the list of
streams are added to the bus object, together with the stream object
and its helpers.
Currently the codes are just copied from the legacy driver, so you can
find duplicated codes in both directories. Only constants are removed
from the original hda_controller.h. More integration work will follow
in the later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and drop bus->rirb_error flag. This makes the code simpler.
We treat -EAGAIN from get_response ops as a special meaning: it allows
the caller to retry after bus reset.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Thinkpad T450 requires the ALC292_FIXUP_TPT440_DOCK as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T450 (20BVCTO1WW) using kernel 4.0-rc7 in
conjunction with a ThinkPad Ultradock.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model uses the same dock port as the previous generation.
Signed-off-by: Yves-Alexis Perez <corsac@debian.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A comma was used instead of a semicolon, which may lead to a build
error.
Fixes: cffd396681 ('ALSA: hda/realtek - Fix the regression by widget power-saving')
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the case for Realtek, VIA codec driver needs this ops as
well for making the widget power-save working.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While enabling the widget power-saving for ALC269 & co, the important
setup was forgotten -- stream_pm ops. Without this setup, the paths
for PCM won't be powered up at all.
Also, the power_filter callbacks used in ALC269 & co need to chain to
the default snd_hda_gen_path_power_filter().
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the generic parser sets codec->power_filter when
power_save_node flag is set. But this overrides the existing filter
that has been already set by the codec driver, thus it looses some
features. Instead, set the default power_filter only when it's not
set yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the check of power_save_node flag at the beginning of the function
so that it skips the rest if the flag isn't set. In this way, we can
call this function safely no matter whether the widget power-saving is
really used or not.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the widget power-saving is enabled, the first automute hook
invocation checks through the whole pins and it also tries to
synchronize the power state. However, this results in a wrong state
because it calls unconditionally snd_hda_jack_detect_state().
This patch adds a check of jack detectability before the actual jack
detection call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new widget power-saving tries to apply the power change no matter
whether the node has a power cap or not. It's bad (although most of
codecs chip just ignore it). Check the capability properly
beforehand.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS version of Fujitsu Lifebook T731 seems to set up the
headphone pin (0x21) without the assoc number 0x0f while it's set only
to the output on the docking port (0x1a). With the recent commit
[03ad6a8c93b6: ALSA: hda - Fix "PCM" name being used on one DAC when
there are two DACs], this resulted in the weird mixer element
mapping where the headphone on the laptop is assigned as a shared
volume with the speaker and the docking port is assigned as an
individual headphone.
This patch improves the situation by correcting the headphone pin
config to the more appropriate value.
Reported-and-tested-by: Taylor Smock <smocktaylor@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell create new platform with ALC288 codec.
This patch will enable headset mode for Dino platform.
[slight code refactoring and compile fix by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin sense will active when power pin is wake up.
Power pin will not wake up immediately during resume state.
Add some delay to wait for power pin activated.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI/DP codec on SKL/BSW is in the power well.
The power well must be turned on before probing the
HDMI/DP codec.
This is a temporary patch, which will power on the
powerwell by adding AZX_DCAPS_I915_POWERWELL for SKL
and BSW. After restructuring and new flag is added,
this patch will be reverted.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
we are dereferencing pcm first then checking pcm. instead now lets put
them in same if condition so that pcm is checked first.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell new platform of ALC256 audio codec.
Support headset mode for Dell ALC256 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent Realtek codecs support the finer power state control on each
widget. Let's enable the new feature.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we assumed that the node attributes like amp values remain
during the power state transition of the node itself. While this is
true for IDT/STAC codecs I've tested, but some other codecs don't seem
behaving in that way.
This patch implements a partial sync mechanism specific to the given
widget node. Now we've merged the regmap support, and it can be
easily written with regcache_sync_region().
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the support of regmap in HD-audio infrastructure.
Many in-house cache codes in HD-audio driver are relaced with the
more standard regmap base now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1436745
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My codec has a beep-generating node:
$ cat /proc/asound/card1/codec#0
Codec: VIA VT1802
...
Vendor Id: 0x11068446
Subsystem Id: 0x15587410
Revision Id: 0x100000
...
Node 0x22 [Beep Generator Widget] wcaps 0x70040c: Mono Amp-Out
Amp-Out caps: ofs=0x0a, nsteps=0x12, stepsize=0x05, mute=1
Amp-Out vals: [0x0a]
Power states: D0 D1 D2 D3
Power: setting=D0, actual=D0
...
But I was missing the:
Control: name=...
entries that I need to manage this widget from alsamixer. With this
patch (based on the similar Mono Amp-Out handling in
patch_conexant.c), I get a new:
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input15
entry in dmesg and controls to manage that beep:
$ cat /proc/asound/card1/codec#0 | grep -A5 Beep
Node 0x22 [Beep Generator Widget] wcaps 0x70040c: Mono Amp-Out
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=1, dir=Out, idx=0, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=1, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x0a, nsteps=0x12, stepsize=0x05, mute=1
Amp-Out vals: [0x12]
Power states: D0 D1 D2 D3
Power: setting=D0, actual=D0
[rebased and modified for the latest tree by tiwai]
Signed-off-by: W. Trevor King <wking@tremily.us>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just forgotten to remove. It's now in sound/hdaudio.h.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model uses the same dock port as the previous generation.
Signed-off-by: Sebastian Wicki <gandro@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target. But this conversion
needs a bit more caution than before.
- In the old code, we just record any verbs as is, and restore them at
resume. For the regmap scheme, this doesn't work, since a few verbs
like AMP or DIGI_CONVERT are asymmetrical. Such verbs are converted
either to the dedicated function (snd_hda_regmap_xxx_amp()) or
changed to the unified verb.
- Some verbs have to be declared as vendor-specific ones before
accessing via regmap.
Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation. Further
optimizations will be brought in the later patches, if any.
This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table. Now it's
dropped by the regmap's cache.
The only tricky conversion is snd_hda_codec_amp_init(). This function
shouldn't do anything if the amp was already initialized. For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode. Only if it returns an error, i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overriding exec_verb op to struct hdac_device so that the call
via snd_hdac_exec_verb() can switch to a different route depending on
the setup. The codec driver sets this field so that it can handle the
errors or applying quirks appropriately. Furthermore, this mechanism
will be used for smooth transition for the regmap support in later
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David suggested that the name "power_mgmt" is too ambiguous. Rename
the flag with a bit clearer one "power_save_node".
Also, add the corresponding description to HD-Audio.txt, too.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some pins are used for controlling the LED with the VREF value.
This patch changes the power behavior of such pins to be constantly
up. A new state, pin_fixed, is introduced to nid_path to indicate
that the path contains the fixed pin. This improves also the
readability a bit for other static routes, too.
Then a helper function snd_hda_gen_fix_pin_power() is called from the
codec driver for such fixed pins, and it will create fake paths
containing only these pins with pin_fixed=1 flag.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the widget PM may turn off the pins, this might lead to the silent
output for beep when no explicit paths are given. This patch adds
fake output paths for the beep widget so that the output pins are
dynamically powered upon beep on/off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs used to have the own power controls but they were disabled
at transition to the generic parser due to the coding assuming the
fixed routes. Now we get the proper support of equivalently fine
power management in the generic parser, and the old kludges can be
replaced with it. This results in the reduction of lots of dead
codes.
The advanced PM feature is disabled as default like before for keeping
the compatible behavior. It's enabled via "Dynamic Power-Control"
mixer element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the finer power state control of each widget
depending on the jack plug state and streaming state in addition to
the existing power_down_unused power optimization. The new feature is
enabled only when codec->power_mgmt flag is set.
Two new flags, pin_enabled and stream_enabled, are introduced in
nid_path struct for marking the two individual power states: the pin
plug/unplug and DAC/ADC stream, respectively. They can be set
statically in case they are static routes (e.g. some mixer paths),
too.
The power up and down events for each pin are triggered via the
standard hda_jack table. The call order is hard-coded, relying on the
current implementation of jack event chain (a la FILO/stack order).
One point to be dealt carefully is that DAC/ADC cannot be powered
on/off while streaming. They are pinned as long as the stream is
running. For controlling the power of DAC/ADC, a new patch_ops is
added. The generic parser provides the default callback for that.
As of this patch, only IDT/Sigmatel codec driver enables the flag.
The support on other codecs will follow.
An assumption we made in this code is that the widget state (e.g. amp,
pinctl, connections) remains after the widget power transition (not
about FG power transition). This is true for IDT codecs, at least.
But if the widget state is lost at widget power transition, we'd need
to implement additional code to sync the cached amp/verbs for the
specific NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does two things:
- code refactoring with a local helper function,
- allow codec drivers to provide the specific PCM stream info pointers
only for overriding the non-NULL entries, instead of copying the
whole.
This simplifies the codec driver side (currently the only user is
alc269's 44kHz fixed rate).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [63e51fd708f5: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021
Fixes: 63e51fd708 ('ALSA: hda - Don't take unresponsive D3 transition too serious')
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
Move the destructor code to device release callback for the codec
object instead. This is a safer place to release the resources than
dev_free callback in general.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The events that are handled by HD-audio drivers are no frequent and
urgent ones, so we can use the standard workqueue without any problem
nowadays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have all pieces ready, and put them into places:
- add the hda_pcm refcount to azx_pcm_open() and azx_pcm_close(),
- call the most of cleanup code in hda_codec_reset() from the codec
driver remove,
- call the same code also from the hda_codec object free.
Then the codec driver can be unbound more safely now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM ops might be set NULL, or cleared to NULL when the driver is
unbound. Give a proper NULL check at each place to be more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the hda_codec object kept the hda_pcm list in an array, and
the codec driver was expected to assign the array. However, this
makes the object life cycle management harder, because the assigned
array is freed at the codec driver detach while it might be still
accessed by the opened streams.
In this patch, we allocate each hda_pcm object dynamically and manage
it as a linked list. Each object has a kref refcount, and both the
codec driver binder and the PCM open/close touches it, so that the
object won't be freed while in use.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memory allocators should have already given the kernel warning
messages, thus we don't have to annoy again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the codec object to have an individual card pointer. Not only
this simplifies the redirections in many places, also this will allow
us to make each codec assigned to a different card object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_build_pcms() does actually three things: let the codec driver
build up hda_pcm list, set the PCM default values, and call the
attach_pcm bus ops for each hda_pcm instance. The former two are
basically independent from the bus implementation, so it'd make the
code a bit more readable.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We leave the pcm field of struct hda_pcm at removal of each device, so
far. This hasn't been a problem since unbinding the codec driver
isn't supposed to happen and another route via snd_hda_codec_reset()
clears all the once. However, for a proper unbind implementation, we
need to care about it.
This patch does the thing above properly:
- Include struct hda_pcm pointer instead of struct hda_pcm_stream
pointers in struct azx_dev. This allows us to point the hda_pcm
object at dev_free callback.
- Introduce to_hda_pcm_stream() macro for better readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we let the controller driver power down the all codecs at the
end of probe. But this can be done better in the codec's dev_register
callback. This results in the reduction of duplicated codes in each
control driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the final bit of runtime PM cleanup: instead of manual
notification of the power up/down of the codec via hda_bus pm_notify
ops, use the standard runtime PM feature.
The child codec device will kick off the runtime PM of the parent
(PCI) device upon suspend/resume automatically. For managing whether
the link can be really turned off, we use the bit flags
bus->codec_powered instead of the earlier bus->power_keep_link_on.
flag. Each codec driver is responsible to set/clear the bit flag, and
the controller device can be turned off only when all these bits are
cleared.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to pass the power_save option value to hda_bus via a given
pointer. This was needed to refer to the value from the HD-audio core
side. However, after the transition to the runtime PM, this is no
longer needed.
This patch drops the power_save value indirection in hda_bus above,
and let the controller driver reprograms the autosuspend value
explicitly by a new helper, snd_hda_set_power_save(). Without this
call, the HD-audio core doesn't set up the autosuspend and flip the
runtime PM. (User may still be able to set up via sysfs, though.)
Along with this change, the pointer argument of azx_bus_create() is
dropped as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is essentially a partial revert of the commit [b1920c21102a:
'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug
report showing the HD-audio bus hang during runtime PM on HP Spectre
XT.
Reported-by: Dang Sananikone <dang.sananikone@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is a bad idea to export static functions. GCC for some platforms
shows errors like:
error: __ksymtab_azx_get_response causes a section type conflict
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous transition of suspend/resume, now move the
power-save code to the standard runtime PM. As usual for runtime PM,
it's a bit tricky, but this simplified codes a lot in the end.
For keeping the usage compatibility, power_save module option still
controls the whole power-saving behavior on all codecs. The value is
translated to pm_runtime_*_autosuspend() and pm_runtime_allow() /
pm_runtime_forbid() calls.
snd_hda_power_up() and snd_hda_power_down() are translated to
pm_runtime_get_sync() and pm_runtime_put_autosuspend(), respectively.
Since we can do call pm_runtime_get_sync() more reliably, the sync
version is used always and snd_hda_power_up_d3wait() is dropped.
Another slight difference is that snd_hda_power_up()/down() don't call
runtime_pm code during the suspend/resume transition phase. Calling
them there isn't safe unlike our own code, resulted in unexpected
behavior (endless wakeups).
The hda_power_count tracepoint was removed, as it doesn't match well
with the new code.
Last but not least, we need to set ignore_children flag in the parent
dev.power field so that the runtime PM of the controller chip won't
get confused. The notification is still done in the bus pm_notify
callback. We'll get rid of this hack in the later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves the suspend/resume mechanisms down to each codec
driver level, as we have a proper codec driver bound on the bus now.
Then we get the asynchronous PM gratis without fiddling much in the
driver level.
As a soft-landing transition, implement the common suspend/resume pm
ops for hda_codec_driver and keep the each codec driver intact. Only
the callers of suspend/resume in the controller side (azx_suspend()
and azx_resume()) are removed.
Another involved place is azx_bus_reset() calling the temporary
suspend and resume as a hackish method of bus reset. The HD-audio
core provide a helper function snd_hda_bus_reset() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we create the standard HD-audio bus (/sys/bus/hdaudio), and bind
the codec driver with the codec device over there. This is the first
step of the whole transition so that the changes to each codec driver
are kept as minimal as possible.
Each codec driver needs to register hda_codec_driver struct containing
the currently existing preset via the new helper macro
module_hda_codec_driver(). The old hda_codec_preset_list is replaced
with this infrastructure. The generic parsers (for HDMI and other)
are also included in the preset with the special IDs to bind
uniquely.
In HD-audio core side, the device binding code is split to
hda_bind.c. It provides the snd_hda_bus_type implementation to match
the codec driver with the given codec vendor ID. It also manages the
module auto-loading by itself like before: when the matching isn't
found, it tries to probe the corresponding codec modules, and finally
falls back to the generic drivers. (The special ID mentioned above is
set at this stage.)
The only visible change to outside is that the hdaudio sysfs entry now
appears in /sys/bus/devices, not as a sound class device.
More works to move the suspend/resume and remove ops will be
(hopefully) done in later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary patch for the hda_bus implementation, removing
the parent device setup to codec device. Since the bus and the class
devices can't be crossed over, leave the sound devices to the default
parent device as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need
to give explicitly here.
Reported-and-tested-by: Misan Thropos <misanthropos@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No real functional change, only take wall clock and system time
in same routine and add accuracy report.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the mixer amp is touched by control elements, we don't have to
power up always; if the codec was suspended at the time, we can just
update the amp cache and it's reflected to the hardware upon resume.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
azx_create_codec() function does actually two things: create a bus and
probe codecs. For the future work, split this to two logical
functions, azx_bus_create() and azx_probe_codecs().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the debugging of runtime PM easier, introduce
azx_has_pm_runtime() and use it in all places checking the runtime pm
driver capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no big merit to handle hda_bus_unsolicited object
individually, as it's tightly coupled with the hda_bus object itself.
Embedding it makes the code simpler in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of copying from the given template, let the caller fills the
fields after creation. This simplifies the code after all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise, the mute led can't work at all.
Tested-by: Taihsiang Ho <taihsiang.ho@canonical.com>
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1410704
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data
driven initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/84r
-----END PGP SIGNATURE-----
Merge tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data driven
initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards"
* tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (542 commits)
ALSA: line6: toneport: Use explicit type for firmware version
ALSA: line6: Use explicit type for serial number
ALSA: line6: Return EIO if read/write not successful
ALSA: line6: Return error if device not responding
ALSA: line6: Add delay before reading status
ASoC: Intel: Clean data after SST fw fetch
ALSA: hda - Add docking station support for another HP machine
ALSA: control: fix failure to return new numerical ID in 'replace' event data
ALSA: usb: update trigger timestamp on first non-zero URB submitted
ALSA: hda: read trigger_timestamp immediately after starting DMA
ALSA: pcm: allow for trigger_tstamp snapshot in .trigger
ALSA: pcm: don't override timestamp unconditionally
ALSA: off by one bug in snd_riptide_joystick_probe()
ASoC: rt5670: Set use_single_rw flag for regmap
ASoC: rt286: Add rt288 codec support
ASoC: max98357a: Fix build in !CONFIG_OF case
ASoC: Intel: fix platform_no_drv_owner.cocci warnings
ARM: dts: Switch Odroid X2/U2 to simple-audio-card
ARM: dts: Exynos4 and Odroid X2/U3 sound device nodes update
ALSA: control: fix failure to return numerical ID in 'add' event
...
Make sure wallclock counter and trigger timestamp are read very
close to each other for better alignment.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite S50D laptop with an IDT codec uses the GPIO4 (0x10)
as the master EAPD.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=915858
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like previous patches, at this time we embed the struct device into
PCM object. However, this needs a bit more caution: struct snd_pcm
doesn't own one device but two, for both playback and capture! Thus
not struct snd_pcm but struct snd_pcm_str object contains the device.
Along with this change, pcm->dev field is dropped for avoiding
confusion. It was meant to point to a non-standard parent. But,
since now we can touch each struct device directly, we can manipulate
the parent field easily there, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patch, this one embeds the device object into hwdep
object. For a proper object lifecycle, it's freed in the release
callback.
This also allows us to create sysfs entries via passing to the groups
field of the device without explicit function calls. Since each
driver can see the device and touch its groups field directly, we
don't need to delegate in hwdep core any longer. So, remove the
groups field from snd_hwdep, and let the user (in this case only
hda_hwdep.c) modify the device groups.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine we need to inform the driver where the docking
station pins are, because it has not been set up by BIOS.
Tested-by: TienFu Chen <tienfu.chen@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1412800
Signed-off-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit commit [33f4acd3b214: ALSA: hda - Enable mic mute hotkey
and LEDs for an HP machine] introduced a quirk for a HP machine
involving with the input event handling. Although the relevant code
is protected via IS_ENABLED(CONFIG_INPUT), this doesn't suffice when
the audio driver is built in while the input is module.
As an easy workaround, this patch forcibly selects CONFIG_INPUT in
Kconfig. This shouldn't be a practical problem since CONFIG_INPUT is
almost mandatory for all systems. Also, this allows to remove the
ugly ifdefs in the code.
Fixes: 33f4acd3b2 ('ALSA: hda - Enable mic mute hotkey and LEDs for an HP machine')
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a component master to be used to interface with the i915
driver. This is meant to replace the current interface which is based on
module symbol lookups.
Note that currently we keep the existing behavior and pin the i915
module while the hda driver is loaded. Using the component interface
allows us to remove this dependency once support for dynamically
enabling / disabling the HDMI functionality is added to the driver.
v2:
- change roles between the hda and i915 components (Daniel)
v3:
- rename display_component to audio_component (Daniel)
v4:
- move removal of i915_powerwell.h from this patch to the next (Takashi)
- request_module fails if module support isn't enabled, so ignore
any error it returns and depend on the following NULL check of the
component ops (Takashi)
- change over to using dev_* instead of pr_* (Takashi)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
chip is already passed to most of the i915 interface functions. Unify
the interface by passing intel_hda instead of chip and passing it to all
functions. Passing intel_hda instead of chip makes more sense since this
is an intel specific interface. Also in an upcoming patch we will use
intel_hda in all of these functions so by passing intel_hda we can save
on some pointer casts from chip to intel_hda.
This will be needed by an upcoming patch adding component support.
No functional change.
v2-3: unchanged
v4:
- pass intel_hda instead of chip
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This struct will be needed by the component code added in an upcoming
patch, so export it into a new hda_intel.h file. At the same time also
merge hda_i915.h into this new header, there is no reason to keep two
separate intel specific header file.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Input_unregister_device will internally free the device, so
input_free_device should not be called.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a similar cleanup like the commit [3db084fd0af5: ALSA: fm801:
PCI core handles power state for us].
Since pci_set_power_state(), pci_save_state() and pci_restore_state()
are already done in the PCI core side, so we don't need to it doubly.
Also, pci_enable_device(), pci_disable_device() and pci_set_master()
calls in PM callbacks are superfluous nowadays, too, so get rid of
them as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine, the mic mute hotkey is connected to GPIO2. We therefore
create an extra input device for this key.
Also enable LEDs connected to GPIO3 and GPIO4.
(Note: if this patch is backported to older kernels, where KEY_MIC_MUTE is
not available, change the KEY_MIC_MUTE to KEY_F20, which was previously used
for mic mute keys.)
BugLink: https://bugs.launchpad.net/bugs/1408295
Tested-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Our fixup system is becoming increasingly complex, so it's becoming
time consuming to figure out which way the fix was applied.
This patch adds a few debug prints to aid when debugging why a specific
fixup was selected.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will help end users figure out what HDA codec they have.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0072 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
stac_store_hints() does utterly wrong for masking the values for
gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately,
this feature is used very rarely, so the impact must be really small.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The iounmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
ad198x_ch_mode_get() ad198x_ch_mode_info() ad198x_ch_mode_info()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The total stream number of Skylake's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented separate stream_tag assignment for input and output streams.
According to hda specification stream tag must be unique throughout the
input streams group, however an output stream might use a stream tag
which is already in use by an input stream. This change is necessary
to support HW which provides a total of more than 15 stream DMA engines
which with legacy implementation causes an overflow on SDxCTL.STRM
field (and the whole SDxCTL register) and as a result usage of
Reserved value 0 in the SDxCTL.STRM field which confuses HDA controller.
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here are a few fixes that have landed after the previous pull
request. All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HRbM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Add new support for ALC298 codec.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Packard Bell EasyNote MX65 with AD1986A codec needs a few fixups,
namely, the pin config overrides to set only the known I/O pins and
the EAPD has to be turned on. In addition, add stereo mix input
forcibly for avoiding the weird KDE behavior by this update.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88251
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new support for ALC256 codec.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New Dell desktop needs to support headset mode for ALC3234.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Skylake and Haswell have the same behavior on display audio. So this patch
applys Haswell fix-ups to Skylake.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... for distinguishing whether it's explicitly enabled via a user hint
or enabled by a driver as a fallback. Now the former case corresponds
to HDA_HINT_STEREO_MIX_ENABLE while the latter to
HDA_HINT_STEREO_MIX_AUTO.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the stereo mix input is explicitly enabled via a user hint, the
driver should create always a capture source enum ctl and disable the
auto-mic switch. Otherwise the behavior gets confused. For doing it,
this patch just sets spec->suppress_auto_mic flag appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862809) and module alias for Skylake
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
The same fixup to enable EAPD is needed for ASUS Z99He with AD1986A
codec like another ASUS machine.
Reported-and-tested-by: Dmitry V. Zimin <pfzim@mail.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just one commit for adding a copule of HD-audio quirk entries.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=U558
-----END PGP SIGNATURE-----
Merge tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixlet from Takashi Iwai:
"Just one commit for adding a copule of HD-audio quirk entries"
* tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add headset Mic support for new Dell machine
The built-in mic boost volume gets almost muted after suspend/resume
on Lenovo Ideapad S210.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88121
Reported-and-tested-by: Roman Kagan <rkagan@mail.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We introduced AZX_DCAPS_ALIGN_BUFSIZE to explicity show that the
controller needs the alignment, with a slight hope that the buffer
size alignment will be disabled as default in future. But the reality
tells that most chips need the buffer size alignment, and it'll be
likely enabled in future, too.
This patch drops AZX_DCAPS_ALIGN_BUFSIZE to give back one more
precious DCAPS bit for future use. At the same time, rename
AZX_DCAPS_BUFSIZE with AZX_DCAPS_NO_ALIGN_BUFSIZE for avoiding
confusion.
AZX_DCAPS_ALIGN_BUFSIZE are still kept (but commented out) in each
DCAPS presets for a purpose as markers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUe7l9AAoJEHm+PkMAQRiGkGcIAIryQ7NKn4IaxUtS807Lx4Ih
obEnx7nNKZTXCZpD/7XQGHMMJyozMJR50PHZESJoHu4Luhv9h7EFRnyJ6MdqMlwn
zla3zY0yRsHwPoJKcHbSE0CPHZz0WPQHj7IEbM+XJz2tMNJfbgTrezElmcCM4DRp
c9ae+ggwZ2cyNYM0r2RSwSJ525WMh69f9dzSUE27fpvkllQgwqNs/jHYz8HNOEht
FWcv5UhvzKjwJS3awULfOB3zH2QdFvVTrwAzd+kbV2Q6T6CaUoFRlhXeKUO6W2Jv
pJM6oj8tMZUkdXEv7EQXT1kwEqC4DULTTTHs4tSF79O1ESmNfePiOwwBcwoM2nM=
=kG1Y
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc7' into for-next
... for allowing more cleanups of hda_intel.c driver-caps where both
upstream and for-next contain the changes.
Dell has new machines. It supports headset Mic and Headphone Mic.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No excitement, here are only minor fixes: an endian fix for the
new DSD format we added in 3.18, a fix for HP mute LED, and a
fix for Native Instrument quirk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUeC5WAAoJEGwxgFQ9KSmkaR4P/0NQWq7Vd5DsRk2DSW1XhYpQ
gZlpxWwc7De4W4MsZQtWSQQn1e3Mm6OYa0srZGzmFQTI1ZBXLZq9O/wott4Q6QgZ
lrWWBzgFenguA8r0bl/VGhFpySt/RE+8hi5Z/vMNG3ATHZxq3DzwE3xB3CaOc+ON
PI5ba7XGLz2Q9txTaFD0g0EZT0uLpZnRZZDD12cHCPvAUIGL1IdvSQio3NFlia+l
9gCTe8uZ8BPUt1+LYAcbVKl5xZn8vVOw9fUbcFj7OOoFu48ve2GgtHRVWdYyI9k9
F6yBOMUQtw+XyKvlcectNbEX/6ORewIV0m15damK4REMQeCapGIaoTXMB6yRd3Ld
zyj1Ld/JAxqrd3Iy0wF4tP/SHy+fJ1e+WSe5rIurCMlUa4CXkSwX65n1DCuonbsG
GsVaXlspSk2j/ZhkqB0rDqTQKqKxSrutqHHwwsfA41iRpOUECmUZU8wM/mj/0THV
0RoWYbJjc0STs+x0ysVo2OudumnMcEhx56SHqJK8Kr1y16m9boxn2exk139qMDb/
Ua6ZGxJiohNICzHsADDcETtnfzOc1bTDhyP058cKAmtmw/U91zpyEAp40xAUe+hL
Ix/z8yVjyIM8RLNizxad90s00hpOmOHDp/idLH4Ok8DoDx97IVhHzqyu8mbiTp8A
wb69fsQApL/lRoTVDbtU
=azkh
-----END PGP SIGNATURE-----
Merge tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
The commit [7a2e9ddc: ALSA: usb-audio: Add native DSD support for
Denon/Marantz DACs] requires the new format definition that has
landed only in for-next branch.
User can pass snoop option to enable/disable the snoop behavior, but
currently azx_check_snoop_available() always turns it off for some
devices. For better debuggability, change the parameter as bint, and
allow user to enable/disable forcibly the snoop when specified via the
module option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new driver_caps bit, AZX_DCAPS_SNOOP_OFF, to set the snoop off
as default. This new bit is used for the checks in
azx_check_snoop_available(). Most of case-switches are replaced with
the new dcaps in each entry.
While working on it, for avoiding to spend more bits, combine three
bits AZX_DCAPS_SNOOP_SCH, AZX_DCAPS_SNOOP_ATI and
AZX_DCAPS_SNOOP_NVIDIA bits into a flat type of two bits. This
reduces the bits usages, and assign AZX_DCAPS_OFF to this empty bit
now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In olden times the snd_hda_param_read() function always set "*start_id"
but in 2007 we introduced a new return and it causes uninitialized data
bugs in a couple of the callers: print_codec_info() and
hdmi_parse_codec().
Fixes: e8a7f136f5 ('[ALSA] hda-intel - Improve HD-audio codec probing robustness')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A number of radeon cards have a HW limitation causing them to be
unable to generate the full 64-bit of address bits for MSIs. This
breaks MSIs on some platforms such as POWER machines.
We used to have a powerpc specific quirk to address that on a
single card, but this doesn't scale very well, this is better
put under control of the drivers who know precisely what a given
HW revision can do.
We now have a generic quirk in the PCI code. We should set it
appropriately for all radeon's from the audio driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
The machine originally use the quirk ALC269_FIXUP_HP_GPIO_MIC1_LED,
but the LED doesn't work at all.
After this change, the machine will change to use
ALC269_FIXUP_HP_MUTE_LED_MIC1 through pin_fixup_tbl[], and the LED
works well.
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New HP machine supported output mute led and input mute led.
ALC286:
GPIO1 to control output mute led.
GPIO5 to control input mute led.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few duplicated codes handling the mute and mic-mute LEDs
via GPIO pins. Let's consolidate to single helpers. Here we
introduced two new fields to alc_spec, gpio_mute_led_mask and
gpio_mic_led_mask, to contain the bit mask to set/clear. Also,
mute_led_polarity is evaluated as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone mute led on the Latitude E5550 can't work. We need to
apply DELL_WMI_MIC_MUTE_LED quirk to this machine.
The machine uses alc293 codec and already applied the quirk
ALC293_FIXUP_DELL1_MIC_NO_PRESENCE through pin_fixup_tbl[].
Here we just let DELL_WMI_MIC_MUTE_LED be chained to
ALC269_FIXUP_HEADSET_MODE, then the machine will have these
quirks ALC293_FIXUP_DELL1_MIC_NO_PRESENCE-->
ALC269_FIXUP_HEADSET_MODE-->ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED.
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have one more Dell machine needs DELL_WMI_MIC_MUTE_LED quirk, but
the machine uses alc293 instead of alc255. So if
DELL_WMI_MIC_MUTE_LED still chain ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
the machine can't use this quirk.
To change this situation, let the DELL_WMI_MIC_MUTE_LED to be a
standalone quirk, and let other quirks chain it.
After this change, this quirk can be chained to any existing quirks,
and as a result, it is possible that this quirk is applied to
a non-Dell machine or a Dell machine without mic mute led on it, but
it is still safe since alc_fixup_dell_wmi() will return an error in
these situations.
And remove the quirk for machine with subsystem id 0x6010 and 0x601f,
these two machines will fall back to the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE-->ALC255_FIXUP_HEADSET_MODE-->
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED through pin_fixup_tbl[].
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The functions kfree() and release_firmware() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Ideapad Z560 has a mute LED that is controlled via EAPD pin
0x1b on CX20585 codec. (EAPD bit on corresponds to mute LED on.)
The machine doesn't need other EAPD, so the fixup concentrates on
controlling EAPD 0x1b following the vmaster state (but inversely).
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=665315
Reported-by: Szymon Kowalczyk <fazerxlo@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will fix no sound in Linux system after reboot from windows.
Change log:
- alc662_fill_coef() is replaced with alc_fill_eapd_coef_idx()
and move into alc_auto_init_amp().
- For ALC262, ALC267, ALC268, ALC269, ALC233, ALC255, ALC280, ALC282,
ALC283, ALC284, ALC285, ALC286, ALC288, ALC290, ALC292, ALC293, ALC294,
ALC668, ALC888VC, ALC888VD, ALC891, ALC892, ALC898 and ALC1150, add update
COEF control for EAPD setting.
- Remove alc269_fill_coef() for update EAPD control line.
ADDITIONAL NOTE:
Many Realtek cdoecs have a COEF bit to switch the master amp control
between COEF and EAPD. Windows drivers seem using COEF while we use
EAPD, which is more standard. As a result, some system suffer from
the silent output when booting after Windows. This patch sets the
COEF bits on the relevant codecs properly to switch to EAPD control.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87771
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the USB-audio disconnect fix and resolves the conflicts
so that we can continue working on development of usb-audio stuff.
Conflicts:
sound/usb/card.c
Without the fix, the mute led can't work on these three machines.
After apply this fix, these three machines will fall back on the led
control quirk as below, and through testing, the mute led works very
well.
PIN_QUIRK(0x10ec0282, 0x103c, "HP", ALC269_FIXUP_HP_LINE1_MIC1_LED,
ALC282_STANDARD_PINS,
{0x12, 0x90a60140},
...
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default EAPD control uses verb command to control EAPD. Some codec
does not have verb command for EAPD. It needs to control by hidden
register.
This update will avoid wrong behavior for some codec. This patch will
fix double setup for EAPD. It just needs to turn on by one site for
verb command or hidden register controlled.
Detailed changes:
- alc889_coef_init() is replaced with alc_update_coef_idx() with a
correct COEF value.
- for ALC262, ALC887 and ALC900, the EAPD setup via the hidden
register is removed because this rather conflicts with the EAPD verb
setup.
- For ALC888-VC, also the hidden register access is removed in
alc888_coef_init().
- Remove the dead #if 0 code for ALC267/ALC268.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These three HP machines all have the same pin config, so we can
change it to a pin quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These HP machines needs GPIO 4 low to enable the headphone amplifier.
In addition, we still need to control LEDs via vref and GPIO.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1387128
Tested-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMI8888 shows the stuttering playback when the snooping is disabled
on the audio buffer. Meanwhile, we've got reports that CORB/RIRB
doesn't work in the snooped mode. So, as a compromise, disable the
snoop only for CORB/RIRB and enable the snoop for the stream buffers.
The resultant patch became a bit ugly, unfortunately, but we still can
live with it.
Reported-and-tested-by: Geoffrey McRae <geoff@spacevs.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put more kerneldoc comments to the exported functions.
Still the generic parser code and the HD-audio controller code aren't
covered yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maruthi Srinivas Bayyavarapu