The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.
Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We've everything we need to support the gmac on Colombus, turn it on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This enables the SPDIF optical audio output on the Radxa Rock
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable USB PHY device for the Porter board. We have to
enable everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA74x, DRA72x and AM57xx EVMs the card detect gpio is
designed as active low gpio. So correcting the dt card detect
gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart2 pinmux is already defined in omap3-igep0020-common.dtsi, remove
the duplicate node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use tabs instead of spaces for indentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The card detect GPIO is using IRQ_TYPE_LEVEL_LOW in the GPIO flag cells
but this defined constant is meant to be used for a IRQ and not a GPIO.
So instead use GPIO_ACTIVE_LOW that seems to be the original intention.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LDO1 regulator (VDD_SD) is connected to SoC's vddshv8. vddshv8 needs to
be kept always powered (see commit 5a0f93c657 ("ARM: dts: Add
am57xx-beagle-x15"), but at the moment VDD_SD is enabled/disabled
depending on whether an SD card is inserted or not.
This patch sets LDO1 regulator to always-on.
This patch has a side effect of fixing another issue, HDMI DDC not
working when SD card is not inserted:
Why this happens is that the tpd12s015 (HDMI level shifter/ESD
protection chip) has LS_OE GPIO input, which needs to be enabled for the
HDMI DDC to work. LS_OE comes from gpio6_28. The pin that provides
gpio6_28 is powered by vddshv8, and vddshv8 comes from VDD_SD.
So when SD card is not inserted, VDD_SD is disabled, and LS_OE stays
off.
The proper fix for the HDMI DDC issue would be to maybe have the pinctrl
framework manage the pin specific power.
Apparently this fixes also a third issue (copy paste from Kishon's
patch):
ldo1_reg in addition to being connected to the io lines is also
connected to the card detect line. On card removal, omap_hsmmc
driver does a regulator_disable causing card detect line to be
pulled down. This raises a card insertion interrupt and once the
MMC core detects there is no card inserted, it does a
regulator disable which again raises a card insertion interrupt.
This happens in a loop causing infinite MMC interrupts.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Louis McCarthy <compeoree@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA74x family of SoCs have a second DSP, that also has
two MMUs just like the DSP1 subsystem. Add the IOMMU nodes
for this DSP2 subsystem in disabled state to the DRA74x
specific DTS file, the nodes would need to be enabled
appropriately in the respective board DTS files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SOCs have two IPUs and one DSP processor
subsystems in common. The IOMMU DT nodes have been added for
these processor subsystems, and have been disabled by default.
These MMUs are very similar to those on OMAP4 and OMAP5, with
the only difference being the presence of a second MMU within
the DSP subsystem for the EDMA port. The DSP IOMMUs also need
an additional 'ti,syscon-mmuconfig' property compared to the
IPU IOMMUs.
NOTE: The enabling of these nodes is left to the respective
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP2 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the dra74x.dtsi file, as the DSP2 processor
subsystem is usually present only on the DRA74x variants of the
DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP_SYSTEM sub-module is a dedicated system control logic
module present within a DRA7 DSP processor sub-system. This
module is responsible for power management, clock generation
and connection to the device PRCM module.
Add a syscon node for this module for the DSP1 processor
sub-system. This is added as a syscon node as it is a common
configuration module that can be used by the different IOMMU
instances and the corresponding remoteproc device.
The node is added to the common dra7.dtsi file, as the DSP1
processor sub-system is mostly common across all the variants
of the DRA7 SoC family.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding child
sub-mailbox (IPC 3.x) nodes for the Beagle X15 EVM boards. This
is needed to enable communication with the respective remote
processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA72 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, and DSP1 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the System Mailboxes 5 and 6 and the corresponding
child sub-mailbox (IPC 3.x) nodes for the DRA7 EVM board.
This is needed to enable communication with the respective
remote processors IPU1, IPU2, DSP1 and DSP2 from the MPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2 and DSP1. These match the
respective node definitions on DRA74x to maintain compatibility for
the equivalent remote processors. There is no DSP2 on DRA72x, and
so the corresponding sub-mailbox node is not added.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sub-mailbox nodes that are used to communicate between
MPU and the remote processors IPU1, IPU2, DSP1 and DSP2.
The sub-mailbox nodes utilize the System Mailbox instances 5 and 6.
These sub-mailbox nodes are added to match the hard-coded mailbox
configuration used within the TI IPC 3.x software package. The
Dual-Cortex M4 IPU1 and IPU2 processor sub-systems are assumed to
be running in SMP-mode, and hence only a single sub-mailbox node
is added for each.
All these sub-mailbox nodes are left in disabled state, and should
be enabled (and modified if needed) as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleaned up the regulators on the wega board. Created a simple bus,
renamed the regulators according to the schematics and added missing
regulator on wega.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 2 gpio keys wired through TS_LCD_GPIO3, TS_LCD_GPIO4
which in turn connected to PCF8575 GPIO pcf_lcd: gpio@20 expander
pins 2 and 3.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra7-evm has 4 user gpio leds connected to PCF8575 GPIO pcf_lcd:
gpio@20 expander pins [4,5,6,7], so add corresponding DT nodes.
Do not enable any triggers by default as not all of them are proved
to work on -RT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT definition for CF8575 GPIO pcf_lcd: gpio@20
expander which is connected to i2c bus 1 and has slave address 0x20.
It allows to control:
- tc_lcd gpios, pins p0-p3
- user leds, pins p4-p7
- control LCD panel power, p15
PCF8575 GPIO pcf_lcd: gpio@20 expander supports interrupt controller
functionality and its INT line is connected to dra7 GPIO6.11 pin.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The analog audio setup consists of:
McASP3 <-> tlv320aic3104 codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from vdd_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO expander's p1 on i2c5 bus 0x26 address is used for selecting
between audio and VIN6 functionality. For VIN6 use an add on card is
needed while audio is present on the board itself.
Select the audio functionality over the VIN6 in the dts file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DVDD is supplied via TPS77018DBVT fixed regulator from evm_3v3
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses tlv320aic3106 codec connected to McASP3. The master clock
for the codec and McASP3 is coming from ATL2.
McASP3 is the master on the I2S bus.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This GPIO expander is used for controlling various muxes on the board.
By default select audio functionality over VIN6 by setting the P1
(vin6_sel_s0) pin to low.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS77018DBVT is used to create 1.8V from avm_3v3_sw's 3.3V connected to
aic3106's DVDD.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the name for the supply as it is in the schematics since the same
supply is used for other peripherals than MMC2, like audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add arch timer node to enable arch-timer support. MT8127 firmware
doesn't correctly setup arch-timer frequency and CNTVOFF, add
properties to workaround this.
This also set cpu enable-method to enable SMP.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add arch timer node to enable arch-timer support. MT8135 firmware
doesn't correctly setup arch-timer frequency and CNTVOFF, add
properties to workaround this.
This also set cpu enable-method to enable SMP.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This cosmetic patch reorder nodes under internal-regs by increasing
address order, as expected.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By default, armada-370-xp.dtsi file has internal RTC enabled.
NETGEAR ReadyNAS 102, 104 and 2120 all use an Intersil ISL12057
I2C RTC chip. The internal RTC not being disabled in the .dts
files of those devices result in the following useless first
line during boot:
[ 4.500056] rtc-mv d0010300.rtc: internal RTC not ticking
[ 4.505684] i2c /dev entries driver
[ 4.513246] rtc-isl12057 0-0068: rtc core: registered rtc-isl12057 as rtc0
This patch marks Armada internal RTC as disabled in individual .dts
files of those devices.
Reported-by: TuxOholic <tuxoholic@hotmail.de>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds DT support for the Seagate Personal Cloud 1 and 2-Bay.
Here are some information allowing to identify these devices:
Product name | Personal Cloud | Personal Cloud 2-Bay
Code name (board/PCB) | Cumulus | Cumulus Max
Model name (case sticker) | SRN21C | SRN22C
Material desc (product spec) | STCRxxxxxxx | STCSxxxxxxx
Chipset list:
- SoC Marvell Armada 370 88F6707, CPU @1GHz
- SDRAM memory: 512MB DDR3 667MHz (16-bits bandwidth)
- SPI flash 1MB (Macronix MX25L8006E)
- 1 or 2 SATA internal ports
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- 1 USB3 host port (PCIe controller ASM1042)
- 1 USB2 host port (SoC)
- 2 push buttons (power and reset)
- 1 SATA LED (bi-color, white and red)
Note that support for the white SATA LED is missing. A dedicated LED
driver is needed.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds DT support for the Seagate NAS 2 and 4-Bay.
Here are some information allowing to identify these devices:
Product name | Seagate NAS 2-Bay | Seagate NAS 4-Bay
Code name (board/PCB) | Dart 2-Bay | Dart 4-Bay
Model name (case sticker) | SRPD20 | SRPD40
Material desc (product spec) | STCTxxxxxxx | STCUxxxxxxx
Chipset list (common):
- SoC Marvell Armada 370 88F6707, CPU @1.2GHz
- SDRAM memory: 512MB DDR3 600MHz (16-bits bandwidth)
- NAND flash 256MB, 8-bits (Micron MT29F2G08AAB or Hinyx H27U2G8F2CTR-BC)
- 2 SATA II ports (SoC)
- 1 Ethernet Gigabit ports (PHY Marvell 88E1518)
- 2 USB3 host ports (PCIe controller ASM1042)
- GPIO fan (4 speeds)
- External I2C RTC (MCP7940NT)
- 3 push buttons (power, backup and reset)
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
Only on 4-Bay models:
- 2 extra SATA III ports (PCIe AHCI controller Marvell 88SE9170)
- 1 extra Ethernet Gigabit ports (PHY Marvell 88E1518)
- I2C GPIO expander (PCA9554A)
- 2 extra SATA LEDs (bi-color, blue and red)
Note that support for the white SATA LEDs associated with HDDs 0 and 1
is missing. A dedicated LED driver is needed.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
All A13 based q8 formfactor tablets use the same backlight setup, add
a backlight devicetree node for controlling the backlight on these devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Q8 format tablets use channel 0 of the PWM controller for backlight dimming.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for the first pwm channel. This is often used for
backlight dimming on tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add dts nodes for the PWM controller on the A13 / A10s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The AXP22x family of PMIC is used with some Allwinner SoCs. This
includes the AXP221, AXP221s and AXP223. They differ in the host
interface, maximum supply current for DCDC1 regulator, and default
voltage and state for various LDO regulators. Also, the AXP221s
does not support fine calibration of the battery fuel gauge.
This patch adds a dtsi file for all the common bindings for these
PMICs. Currently this is just listing all the regulator nodes. The
regulators are initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the PCIe controller and clock for the Porter board.
This patch is analogous to the commit 485f3ce67c ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and the MTD partitions
on it.
This patch is mostly analogous to the commit f59838d448 ("ARM:
shmobile: henninger: add QSPI DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LinkSprite pcDuino v3 Nano's two USB host ports are powered by a
single RT9701GB regulator, which has its enable input tied to the A20's
PD2 pin, pulled up to 3v3 via a 10k resistor.
However, the script.bin that shipped with the device listed PH11 and PH3
as Vbus control pins for the two USB ports. Neither of these are
actually connected to anything.
Siarhei Siamashka spotted this problem while reviewing the other
LinkSprite boards. This patch fixes it by only defining a single
regulator, controlled by PD2. Testing shows that the USB ports are now
(correctly) only powered up once the USB PHY driver is loaded.
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a separate pinctrl node for the UART3 CTS and RTS pins shared between
the A10s and A13.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The uart3 pins are shared between the A10s and A13, move the pinctrl node
to the common DTSI to avoid duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The R8 is very close to the A13, but it still has a few differences,
notably a composite output, which the A13 lacks.
Add a DTSI based on the A13's to hold those differences.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Enable the otg/drc usb controller on the pcDuino1/2 board. Note
that the pcDuino1 FEX file from the vendor contains the following
information in the [usbc0] section:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PB09<1><0><default><0>
While the pcDuino2 FEX has:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PD02<1><0><default><0>
The ID pin is indeed PH4. The PD2 pin can be used to switch power
on/off for the USB Type A receptacle on pcDuino2, but it has nothing
to do with the MicroUSB OTG receptacle. The VBUS pin of the MicroUSB
receptacle is always connected to 5V according to the schematics
(both pcDuino1 and pcDuino2) and confirmed by doing some tests on
pcDuino2. The PH5 pin is just one of the pins on the J8 expansion
header and has nothing to do with USB OTG. The PB9 pin is pulled
up and connected to the N_VBUSEN pin of AXP209 PMIC, while the
VBUS pin of AXP209 only has a capacitor between it and the
ground (this pin is not used for anything else).
To sum it up. Only the ID pin (PH4) has a real use. And 5V voltage
is always served to the MicroUSB OTG receptacle no matter what is
the state of the PB9/PD2 pins.
This patch has been tested on pcDuino2 to work fine in a host role
with a USB keyboard connected via an OTG cable. It also works fine
in a device role (cdc_ether) with a regular Micro-B cable connected
to a desktop PC.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pcDuino1 board does not use any power switches at all for its
two USB host ports and the VBUS pins are always connected to 5V.
The pcDuino2 board uses the RT9701GB power switch for its single
USB host port, but the USB_EN pin (PD2) is pulled up with a 10K
resistor. So that the USB power is still enabled by default,
resulting in the same behaviour as pcDuino1 if nobody touches
the PD2 pin. This minor difference is going to be handled in a
follow-up patch, introducing a separate dts file for pcDuino2.
The primary reason for this fix is that the current dts file
unnecessarily meddles with the PH3 and PH6 pins. But the PH6 pin
is available on the Arduino-compatible expansion header and may
have a better use for other purposes. This patch fixes the
problem and now the PH6 pin can be used with the GPIO sysfs
interface. Tested on a pcDuino2 board with a multimeter:
echo 230 > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio230/direction
echo 0 > /sys/class/gpio/gpio230/value
echo 1 > /sys/class/gpio/gpio230/value
USB still works as expected too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Bananapi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-bananapi.dts doesn't contain regulator nodes for the AXP209 PMU
driver, so add them to allow for voltage-scaling with cpufreq-dt. Also
add board-specific OPP to use slightly higher voltages at lower
frequencies since Kevin Hilman reported that not all BananaPi boards run
stable at the default voltages inherited by sun7i-a20.dtsi.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace console with stdout-path so that we don't have to put the
console on the kernel command line.
Remove earlyprintk to allow the kernel to boot on a system even
if DEBUG_LL is configured for another system.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Merge "Broadcom devicetree changes for v4.4" from Florian Fainelli:
This pull requests contains the following Broadcom SoCs Device Tree changes:
- Brian Norris documents the BCM7445 SoCs Power Management controllers and
hardware and updates the reference BCM7445 Device Tree with these nodes
- Florian Fainelli documents the BCM7xxx write-pairing feature in the top-level
BCM7xxx binding document
- Hauke Merthens enables the NAND controller for the Asus RT-AC87U and adds the
GPIO pin controlling the USB power supply on Netgear R6250
- Jon Mason adds support for the NorthStar Plus SoC by providing a top-level
binding document and the minimalist device tree skeleton for these SoCs
- Rafal Milecki adds support for the Netgear R7000 (BCM5301x SoC)
- Ray Jui provides a set of Cygnus DT changes that make the Device Tree clearer
and more correct with respect to how the hardware is designed. He also enables
the NAND controller on the bcm911360_entphn design, enables a bunch of
peripherals on the bcm958305k evaluation board, and adds a skeleton .dtsi file
for the touchscreen extansion board(s)
* tag 'arm-soc/for-4.4/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: move aliases back to .dts in Cygnus
ARM: dts: fix Cygnus nand device node
ARM: dts: enable touchscreen support on Cygnus
ARM: dts: Enable NAND support on bcm911360_entphn
ARM: dts: Enable various peripherals on bcm958305k
ARM: dts: Reorder Cygnus peripherals
ARM: dts: Move all Cygnus peripherals into axi bus
ARM: dts: Put Cygnus core components under core bus
ARM: dts: Use label for device nodes in Cygnus dts
ARM: dts: consolidate aliases for Cygnus dt files
ARM: BCM5301X: Netgear R6250 add USB GPIO
Documentation: bindings: brcmstb: Document write-pairing
ARM: dts: brcmstb: add BCM7445 system PM DT nodes
Documentation: dt: brcmstb: add system PM bindings
ARM: BCM5301X: add NAND flash chip description for Asus RT-AC87U
ARM: BCM5301X: Add DT for Netgear R7000
ARM: NSP: add minimal Northstar Plus device tree
dt-bindings: Create Documentation for NSP DT bindings
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWFta1AAoJEPOmecmc0R2BwsoH/iAhuYW/AMw9theS5e3QKYaT
AetDQHjjXPkbQpkMMxVpyyIGhBvHWHX+iTINqkVVx5MVlhvC1xmF4oJ6Yo4lbDVF
S6YgYrgI72P4inP0v3DZhJ2CpYB7bTVcPsU/ZiJOacvwKk2rgXWqE+nbBrZHpYbe
pDR9ONdOB0PsXfTsawcjb1FmK2/+xwRhHZJUSdlQRIoUZe1qIOjR2Lx25sprQ6vb
v6sBuY2T/rrWlKE0ME6HtdcA2s7HLKY1E1OdQPr15ceXR8k0yRz0dqH0ydULtZVZ
d6ZghxS+1ygir6Uw4sUXQa5QZjEeWU7M9+z6jCdKLEH/jUuaTFKFj+tko9uboa8=
=LB4D
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 changes for 4.4" from Heiko Stuebner:
DTS changes including one new Veyron-board and the Radxa Rock2
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
* tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the support power-domain node on RK3288 SoCs
ARM: dts: rockchip: add rk3288-firefly iodomains
ARM: dts: rockchip: fixup firefly mmc supplies
ARM: dts: rockchip: add rk3288-popmetal iodomains
ARM: dts: rockchip: add rk3288-popmetal mmc supplies
ARM: dts: rockchip: add rk3288-popmetal board to dtb list
ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board
ARM: dts: rockchip: support highspeed sd-cards on rk3066a boards
ARM: dts: rockchip: support highspeed sd-cards for rk3188-radxarock
ARM: dts: rockchip: Add the hdmi-ddc pinctrl settings for rk3288
ARM: dts: rockchip: Remove specific cts pullup from veyron
ARM: dts: rockchip: pull up cts lines on rk3288
ARM: dts: rockchip: add veyron-jaq board
ARM: dts: rockchip: Add support for SD/MMC on MarsBoard-RK3066
dt-bindings: add power-domain header for RK3288 SoCs
Explicitly use the SoC specific compatible strings in kirkwood.dtsi and
dove.dtsi, so that the crypto devices have access to the TDMA feature
when attached to the new CESA driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The new bindings split the crypto and sram node in two separate devices.
Modify the existing crypto nodes to match the new representation.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add crypto related nodes in armada-38x.dtsi.
[gregory.clement@free-electrons.com: Fix typo for compatible string
armada38x instead of armada375]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the Porter board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C2 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
This patch is analogous to the commit 8d62f4f753 ("ARM: shmobile:
henninger: add VIN0/ADV7180 DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the I2C2 device node.
This patch is analogous to the commit 29a647c396 ("ARM: shmobile:
henninger: add I2C2 DT support") as there are no differences between
the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We can add more domains node in the future.
This patch add the needed clocks into power-controller.
As the discuess about all the device clocks being listed in
the power-domains itself.
There are several reasons as follows:
Firstly, the clocks need be turned off to save power when
the system enter the suspend state. So we need to enumerate
the clocks in the dts. In order to power domain can turn on and off.
Secondly, the reset-circuit should reset be synchronous on RK3288,
then sync revoked. So we need to enable clocks of all devices.
In other words, we have to enable the clocks before you operate them
if all the device clocks are included in someone domians.
Thirdly, as the chip designs for PM hardhare. we need turn on the noc
clocks, if we are operating the "pd_vio" domain to enter the idle status.
The device's clock be included in domains that needed turn on if do that.
The clocks in the dts are needed to enable before you want to happy work.
At the moment, This patch is very good work for PM hardware.
Also, we can add these clocks in the future if we have some hidden clocks.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
[add necessary power-domain properties to keep drm subsys working]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the iodomains node and reference the correct regulator for each
domain. This also includes adding the currently unused dvp regulators.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix some incorrect references to mmc regulators.
vccio_wl for example is the io-voltage supply not the core supply
of the wifi module itself, which is vbat_wl instead.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the iodomains node and reference the correct regulator for each
domain. This also includes adding the currently unused dvp regulators
and fixing up two regulators to follow the naming in the schematics.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The popmetal board was not included in the list of Rockchip boards,
so was only built when explicitly called with make rk3288-popmetal.dtb
but not in a generic make dtbs, so add the missing entry.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add cap-sd-highspeed and cap-mmc-highspeed for rk3066a-bqcurie2
and rk3066a-rayeager boards to make sd cards run faster.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add cap-sd-highspeed and cap-mmc-highspeed for rk3188-radxarock
board to make sd cards running faster.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pins for i2c5 can either be configured as "I2C5" which means that
they're controlled by the normal RK3288 I2C controller or as "EDP / HDMI
I2C". It's unclear why EDP is referenced here since apparently setting
the mux to this position enables I2C communication using the dw_hdmi
block with a patch like <https://patchwork.kernel.org/patch/7098101/>.
There appear to be some reasons why using the builtin I2C controller in
dw_hdmi is better than using the normal RK3288 I2C controller, so boards
based on rk3288 might eventually want to use this pinmux if it's known
to work.
Once driver support in dw_hdmi lands, boards would use this by selecting
this pinctrl for the HDMI block and then _not_ specifying a ddc-i2c-bus
and _not_ setting the status to "okay" for i2c5 (which uses the same
pins).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the previous patch ("rk3288: pull up cts lines") this is redundant,
I sent that patch for the same reason this existed here, so the lines don't
wiggle randomly when disconnected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The flow control lines from a user accessible UART are optional,
the user might not have anything connected to those pins.
In order to prevent random interrupts happening and noise affecting
the cts pin should be pulled up.
Note that the default state for that pin on the rk3288 is pulled up,
so this patch merely restores them.
This is similar to what we're already doing with the RX pin,
so it should be safe. At worst it might be a slightly higher power usage
(through ~50 kohms) when the cts is low.
Suggested-by: Neil Hendin <nhendin@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
a.k.a. Haier Chromebook 11, and others
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables SDMMC0 on the board and gives a basic support for SD cards.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ceDx
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.4" from Simon Horman:
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
* tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (28 commits)
ARM: shmobile: porter: add Ether DT support
ARM: shmobile: fix SILK board name
ARM: shmobile: r8a7794: add HS-USB DT support
ARM: shmobile: dts: Add common file for AA121TD01 panel
ARM: shmobile: r8a7794: link PCI USB devices to USB PHY
ARM: shmobile: silk: enable USB PHY
ARM: shmobile: r8a7794: add USB PHY DT support
ARM: shmobile: porter: initial device tree
ARM: shmobile: add Porter board DT bindings
ARM: shmobile: silk: enable internal PCI
ARM: shmobile: r8a7794: add internal PCI bridge nodes
ARM: shmobile: r8a7790: lager: add pinmux for iic0
ARM: shmobile: r8a7778: tidyup SSI resource region
ARM: shmobile: r8a7791: tidyup SSI resource region
ARM: shmobile: r8a7790: tidyup SSI resource region
ARM: shmobile: lager: use CCF for audio clock
ARM: shmobile: koelsch: use CCF for audio clock
ARM: shmobile: silk: add VIN0/ADV7180 DT support
ARM: shmobile: r8a7794: add VIN DT support
ARM: shmobile: silk: add I2C1 DT support
...
Enable SATA0 device for the Porter board.
This patch is analogous to the commit 5a62ec5700 ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Peach boards use the EC to store the vboot context information,
so add the corresponding properties on the EC node to indicate so.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Emilio Lopez <emilio.lopez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
1. Enable DMA on Exynos4 serial ports. This old patch uncovered
a number of other issues in dmaengine and samsung serial driver.
All of known issues are resolved so finally enable the DMA for UART.
2. Fix incorrect location of display-timings node (FIMD->DP node)
on Arndale, SMDK5250 and SMDK5240 boards.
3. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OWHD
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.4-2' of http://github.com/krzk/linux into v4.4-next/dt-samsung
Device Tree improvements for Exynos based boards (updated pull request):
1. Enable DMA on Exynos4 serial ports. This old patch uncovered
a number of other issues in dmaengine and samsung serial driver.
All of known issues are resolved so finally enable the DMA for UART.
2. Fix incorrect location of display-timings node (FIMD->DP node)
on Arndale, SMDK5250 and SMDK5240 boards.
3. Minor cleanups.
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Define the Porter board dependent part of the SDHI0/2 device nodes along
with the necessary voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...
This patch is analogous to the commit 1299df03d7 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3A9d
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
Merge "SoCFPGA DTS updates for v4.4" from Dinh Nguyen:
- Add base arm64 dts for Statrix 10
- Peripheral updates for Arria10(USB,I2C,UART)
* tag 'socfpga_dts_for_v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: Add base stratix 10 dtsi
ARM: socfpga: dts: enable USB and I2C on Arria10 SoCDK
ARM: socfpga: dts: add clock fields for I2C, UART and USB on Arria10
- some DT fixes: dma declaration, led labels
- disable some nodes: PMIC on sama5d3 Xplained, unused i2c1 on at91sam9n12ek
- add some others that were missing: touchscreen, cryto nodes, LCD panels or
image capture properties on various boards
- as the new pinmux for sama5d2 was accepted, we can now add the definitions
and the actual muxing for sama5d2 Xplained board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWDSc+AAoJEAf03oE53VmQSu0H/RSxt4bK9Mb3p5le7pXCefXD
JO53I56T7lAjQcfbzGF9yPyeRfYDImVdehXMs+2eY8bBzasLbayeqTJq+SIwpLv7
xOgfnSZos7bzz+efwF5r937EvW1G9/VeO0OYksvKt0FdJPeMaj55/x9E7022sgSh
dAyx1+L8u+w+HcFEzLESAuXXCaredMMdVH+a0i5CEP02OQATVovR5Mb29GiQtdmU
CHai+ziJSYzmqG0/9QShR7gWFmlJuEpAE0fyukGGFq9AJWuyDvAQlTVu5UQblra9
0SQ2fOKh4J22E2cLYlt1K+JBW2M8kw98QGx3wCDtDiP4IsssVtw+C/VLCwvACKo=
=whS/
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "First batch of DT changes for 4.4:" from Nicolas Ferre:
- some DT fixes: dma declaration, led labels
- disable some nodes: PMIC on sama5d3 Xplained, unused i2c1 on at91sam9n12ek
- add some others that were missing: touchscreen, cryto nodes, LCD panels or
image capture properties on various boards
- as the new pinmux for sama5d2 was accepted, we can now add the definitions
and the actual muxing for sama5d2 Xplained board
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: add device pin muxing
ARM: at91/dt: add sama5d2 pinmux
ARM: at91/dt: ov2640: add hsync/vsync-active property
ARM: at91/dt: sama5d4 xplained: enable the led D8
ARM: at91/dt: sama5d4ek: Add support of QT1070 and Maxtouch
ARM: at91/dt: sama5d4: enable crypto nodes
ARM: at91/dt: sama5d4: add pioD pin mux mask and enable pioD
ARM: at91/dt: sama5d3: update iio config for touchscreen
ARM: at91/dt: sama5d3 xplained: disable pmic
ARM: at91/dt: at91sam9x5: enable iio touchscreen for 9x5ek
ARM: at91/dt: at91sam9n12ek: disable i2c1
ARM: at91/dt: at91sam9n12ek: fix the led labels name
ARM: at91/dt: corrections to i2c1 declaration to sama5d4
These are just two followup cleanups for commits that are in v3.17-rc1 and
waited in my private tree for application since that time.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJWCtIwAAoJEMH8FHityuwJFPYH/2LJpi0yUhI01s0D9U5rZgjl
8mLP70utAMaqXiGqP/O0ndH+za5TrrUTwDJE5jhAHru1Q6q62Ld2BfOR5+K8zlrP
4UDGBDj3ePJgEtbSsJYJIRT+AKque2GONbeGpJh2arPrNamWChKIz8HoGSgwdRlx
TvQuVFEa6C3ujP0ATM8x54f0vR4bYm9WmBS522DwZQY4JpGZC005A3Quw6fmFxPJ
vJRo1fE1d2OZ3Cuxb15m8PLtZw6sbMdMwgyirAFGrJsN9u/V6BzsSzH0s8suT7IP
WIohnmYtFSUfkQjaGrMl2wIpJSsIzettiXf9GrQDXSGZsQ4k7sW3U+qrcZ7ZUR4=
=ngv1
-----END PGP SIGNATURE-----
Merge tag 'efm32-for-4.4-rc1' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
Merge "efm32 cleanups for 4.4-rc1" from Uwe Kleine-Koenig:
These are just two followup cleanups for commits that are in v3.17-rc1 and
waited in my private tree for application since that time.
* tag 'efm32-for-4.4-rc1' of git://git.pengutronix.de/git/ukl/linux:
ARM: efm32: switch to vendor,device compatible strings
ARM: efm32: switch to properly namespaced location property
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0wuy
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.3" from Simon Horman
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
* tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4XBA
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.3" from Maxime Ripard:
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
* tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lpRb
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v4.3" from Kukjin Kim:
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
On the Arria10 Devkit, the I2C bus has a serial EEPROM and an RTC
hanging off it. Also, enable the USB node.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the required clock fields for all the I2C nodes. Also add missing clock
fields for UART0 and USB1.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes but by not using a deprecated
property, new DTS based on this one will not carry the same issue.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch moves the display-timings node from fimd to dp to reflect the
device tree bindings change.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[tomeu.vizoso@collabora.com: Rebased]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Define the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
This patch is analogous to the commit 26b0d2cf73 ("ARM: shmobile:
henninger: add Ether DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a PWM node in the Berlin BG2CD device tree, using the
newly added Berlin PWM driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds a PWM node in the Berlin BG2 device tree, using the
newly added Berlin PWM driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds a PWM node in the Berlin BG2Q device tree, using the
newly added Berlin PWM driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This allows voltage-scaling with cpufreq-dt. The reliability of
voltage-scaling has been checked by reducing the voltage of all
operating points by 0.025V (for extra safety headroom) and running
libjpeg-turbo decoding tests on 5 pcDuino2 boards. It means that
the standard sun4i voltages should be perfectly fine too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Define the R8A7794 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Mitsubishi AA121TD01 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB PHY device for the SILK board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the R8A7794 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which is a slightly modified version of the Henninger board).
SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently, BG2Q shares a compatible with BG2. This is incorrect, since
BG2 and BG2Q use different USB PLL dividers. In reality, BG2Q shares a
divider with BG2CD. Change BG2Q's USB PHY compatible string to reflect
that.
Cc: <stable@vger.kernel.org> # v4.2.0-
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The hummingbird A31 has 2 rtc devices available: one in the SoC,
and a pcf8563 external rtc on i2c2.
For some unknown reason, the onboard backup battery alone can not
supply enough power to the internal rtc. When external power is
removed, the internal rtc would reset. Hence we want to use the
external one by default.
Add aliases for the rtc devices with the external one as rtc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the I2C0 bus and the some of the I2C devices on the Hitex
LPC4350 eval board.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The Hitex LPC4350 eval board has a Spansion S25SL064P SPI-NOR Flash connected
to the SPIFI perherial.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Most of the peripherals on LPC18xx/43xx devices have their reset
lines hooked up to internal reset controller (RGU). Add reset
entries to the device nodes so a driver can use the reset line.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
NXP LPC SoCs family, which includes LPC18xx/LPC43xx, provides a State
Configurable Timer (SCT) which can be configured as a Pulse Width
Modulator.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the watchdog timer found on LPC18xx/LPC43xx.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add dmas entries to the four UART peripherals on LPC18xx/43xx devices
so that DMA can be used to transfer data.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add dmas entries to the two SSP peripherals on LPC18xx/43xx devices
so that DMA can be used to transfer data.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This patch configure correctly the MMC-0 clock for STiH418 platform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the R8A7794 internal PCI bridge devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now we have default pinconfig groups for each SPI
controller ensure it is used by the SPI controller
node.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the RMII pinctrl support for the Synopsys
MAC on STiH407 SoCs.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pinconfig for IRB TX and IRB UHF.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the missing SD pinctrl config
for mmc/sd controller 0. This is required to enable the
B2144A daughter board that exposes this controller as a sd
slot.
Signed-off-by: Nebil BEN MEFTEH <nebil.ben-mefteh@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pin config for systrace for
STiH407 family silicon.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds NAND flash support controller pin configuration
for STiH407 family silicon.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the pin configuration for the NOR flash controller.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add missing serial 3 pinctrl config. This can be used
on b2206 HVK, where it defaults to PIO31[3] & PIO31[4],
alternate 1.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the spi pinctrl configurations for all SPI
controllers, and also the alternate muxings which
can be used depending on board design.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
i2c3 controller can use several sets of pins depending
on board design. This patch adds the missing alternate
pinconfigs.
Signed-off-by: Seraphin Bonnaffe <seraphin.bonnaffe@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This pin setup provides the correct configuration in order to
interact with the CEC HW.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Nicolas Vanhaelewyn <nicolas.vanhaelewyn@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
There are 2 revisions of the Exynos5250 Snow Chromebook that were
shipped: Rev4 and Rev5. The only difference between these 2 revisions
is the codec, Rev4 has a max98095 codec while Rev5 has a max98090.
Mainline only supports Rev4 so this patch moves the common device
nodes to a DTSI file and adds a DTS for the Exynos5250 Snow Rev5.
The Snow Rev5 DTS is based on the DTS found in the ChromiumOS 3.8
tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
1. Finally fix booting of all 8 cores on Exynos Octa (Exynos542x): all
8 cores are booting and can be used. The fix, based on vendor
code and bootloader behavior, is as for time being only
for MCPM enabled path.
2. Fix thermal boot issue on SMDK5250.
3. Fix invalid clock used for FIMD IOMMU.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xcnj
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.3' of http://github.com/krzk/linux into v4.3-samsung-fixes
Fixes for Exynos (DT and mach code):
1. Finally fix booting of all 8 cores on Exynos Octa (Exynos542x): all
8 cores are booting and can be used. The fix, based on vendor
code and bootloader behavior, is as for time being only
for MCPM enabled path.
2. Fix thermal boot issue on SMDK5250.
3. Fix invalid clock used for FIMD IOMMU.
The UART2 memory space starts at address 0x30890000 (UART2_URXD).
Fix it so that UART2 can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 9496734502 ("ARM: dts: add imx7d soc dtsi file")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
=m29x
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc3' into next
Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
A board might not expose the USB2.0 ports, so disable them by default in SoC
file, and enable them in b2120 board.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add crypto related nodes in armada-375.dtsi.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The display nodes are common to both STiH407 and STiH410, move them to the
family file.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The PWM may not be used on some boards, so enable them only the board file.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add crypto related nodes to armada-xp.dtsi.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the description of the CPU config registers in the
Armada 370 and Armada XP Device Tree. Since the registers are in fact
different between the two SoCs, a different compatible string is used.
Note that the Armada 370 node is currently unused, but it is
nonetheless added for consistency with the addition on the Armada XP
side.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.
Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add usb otg support for Orange pi, based on Orange pi mini.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the orangepi-mini.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node representing the usb power supply part of the axp209 pmic, note
that the usb power supply and the (to be added later) ac power supply will
each have their own child-node, so that they can be separately specified
as power-supply for other nodes using a power-supply property with a
phandle pointing to the right axp209 child-node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use 'ldoN_reg: LDON' syntax and drop the deprecated
'regulator-compatible' property.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The pinctrl settings in i2c_0 and i2c_1 are already provided
through the exynos4 dtsi.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The sysmmu_fimd1_1 should bind the clock CLK_SMMU_FIMD1M1, not the clock
CLK_SMMU_FIMD1M0. CLK_SMMU_FIMD1M0 is a clock for the sysmmu_fimd1_0.
This wrong clock binding causes the problem that is blocked in iommu_map
function when IOMMU is enabled and exynos-drm driver tries to allocate
buffer via DMA mapping API on Odroid-XU3 board.
Fixes: b700451678 ("ARM: dts: add sysmmu nodes for exynos5420")
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
With default config on smdk5250 latest tree throws below message:
[ 2.226049] thermal thermal_zone0: critical temperature reached(224 C),shutting down
[ 2.227840] reboot: Failed to start orderly shutdown: forcing the issue
and hangs randomly because it reads wrong temperature value.
I can't figure out any direct relation between LDO10 and TMU from board
schematics which I have. So making LDO10 always-on to fix issue for now.
Signed-off-by: Yadwinder Singh Brar <yadi.brar01@gmail.com>
[pankaj.dubey: resubmitted after rebasing to latest kgene tree]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
797a0626e0 ("ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain")
added CPG/MSTP clock-cells domain support, but it was missing sound
support. This patch adds it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: updated commit id referred to in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
484adb0058 ("ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain")
added CPG/MSTP clock-cells domain support, but it was missing sound
support. This patch adds it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: Updated commit id referred to in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- One fix for i.MX6 Rex Pro board to remove a duplicated pinctrl entry
which causes error for USB pinctrl setup.
- Fix MC34708 PMIC interrupt level for imx53-qsrb board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWCM4UAAoJEFBXWFqHsHzOfEIIAJUXni9UzPgZ77RvX8tn8jCU
E3GBEDXlTHmUaTMiCSIZaB00X/rEFGO/GMd1zUFxGZW3yTX4FJ/pCn3dNbFqmYLY
T2v91D2r7Fbyugm8hGnbHoPlmk4RkyJ0oSIBGaR2PXnbrKYJHYgDBxUjsKH012LS
2+ea3EF5bJ3eCtAI50GQwZXJc1qAJ9XoMSyhIoJXVFtwJ65JPdM1ntn/yBYEZD01
uBnVwPw7EQzuPYwzdmj38BWPxJUxdDSj6SvZGtK2MVWl8lUvcHRiNcEX4lFMBMVi
6vs7xQ7T9YnAh4jVjsAHWb9qjFtomLkuDhkClvUJHSHPU+Ue++iYSofwU6GnM5Y=
=tm7i
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.3:
- One fix for i.MX6 Rex Pro board to remove a duplicated pinctrl entry
which causes error for USB pinctrl setup.
- Fix MC34708 PMIC interrupt level for imx53-qsrb board.
* tag 'imx-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: fix usb pin control for imx-rex dts
ARM: imx53: qsrb: fix PMIC interrupt level
ARM: imx53: include IRQ dt-bindings header
Signed-off-by: Olof Johansson <olof@lixom.net>
A33 Q8 tablets with the ippo-q8h-v1.2 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v1.2.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the driver respects IRQ trigger settings from device tree, let's
fix them up in individual DTSes (note that the driver is still compatible
with older DTSes).
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add node for the DMA multiplexer placed in front of the PL080 DMA
controller on lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add the NXP LPC1773 SPIFI (SPI Flash Interface) flash controller
node to the dtsi for all lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add the NXP LPC1850 RGU (Reset Generation Unit) reset controller
node to the dtsi for all lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The regulator-compatible property from the regulator DT binding was
deprecated and the correct approach is to use the node's name.
This patch has no functional changes since the values of the node's
name and the regulator-compatible match for all the regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port
This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Marsboard A10.
Similar to Cubieboard, the 5V of the otg is directly connected to the
general 5V, so we only use the id pin.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add IRQ configuration for bma250 accelerometer.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33 has the same "Security System" crypto engine as A10/A20, but with a
separate reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LCD backlight on the A23/A33 Q8 format tablets is enabled
with a GPIO controlled regulator, and brightness controlled with
the SoC's PWM controller.
The backlight is powered from the AXP223 PMIC's DC1SW output,
which is not supported yet. A proper bootloader is required
to enable it.
The brightness levels are arbitrary. The FEX files do not have
such information. As such, actual brightness levels may differ
from device to device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Even though it's not mentionned in the A23 user manual, the A23 has a gate
for the AHB1 clock to the msgbox IP. Add it to the clock-indices.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AHB1 gates were assumed to be identical between the A23 and the A33,
which turned out to be wrong. Move the A23 gates definition to the A23
DTSI.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A33 has a different gates array than the A23, add the node to the DT.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits adds a generic dts file for q8 formfactor a13 based tablets.
The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.
This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is the sun5i / a13 version of sun8i-q8-common.dtsi for use in dts
files for a13 q8 based tablets. Compared to sun8i this uses uart1 for the
serial console, and PG0 for card-detect for mmc0.
This also adds pmic and otg support, which both use the same config on
all known q8 a13 devices. This is not present in sun5i-q8-common.dtsi
because pmic / otg support for sun8i has not yet been merged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PWM controller has 2 outputs, with one usable pin for each.
Add a pinmux setting for the first channel. This is often used
for backlight dimming on tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23/A33 have a PWM controller that is compatible to the one on the A20.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add support to the keypad clock on sun7i
Signed-off-by: Yassin Jaffer <yassinjaffer@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add mma8452 accelerometer to sun6i-a31-colombus.dts.
Signed-off-by: Sander Vermin <sander@vermin.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
This commit adds a dts file adding support for this top set box.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The emac pins on an A10s can also be routed to the outside through
PORTD rather then through PORTA, add a pinctrl node for this.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20 OLinuXino Micro features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20 OLinuXino Lime2 features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The OLinuXino A10S micro features an eeprom. According to the eeprom.txt
binding document, we should use the manufacturer and 'at' is not the
proper manufacturer id according to the vendor-prefixes.
This patch takes the proper vendor-prefix and uses it for the eeprom
node.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A10 OLinuXino Lime features an eeprom that is always on the
board. This patch adds it to the dts.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cheap allwinner based devices in the q8 enclosure come in many variants,
all sharing the case and a number of other basic features.
They differ in the display, touchscreen, accelerometer and wifi chips
used.
This commit adds 2 dtsi files defining the shared features of all the
q8 tablets. sunxi-q8-common.dtsi defines features shared amongst all
q8 tablets, sun8i-q8-common.dtsi defines features shared amongst all
a23 / a33 based q8 tablets, but not with a13 q8 based tablets.
a13 based tablets use a different card-detect pin for the mmc, and
use uart1 instead of the r_uart for the serial console.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun6i also has the LRADC for tablet buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable i2c1 and i2c2 controllers, these are used for the touchscreen resp.
the accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable support for the tablet keys which are connected via the lradc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg controller on the inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use axp209.dtsi and add regulator nodes for the regulators used on the
inet97fv2 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet97fv2 tablet only has a usb-2 wifi device connected to the second
ehci controller, disable the first ehci controller and both ohci
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the cubieboard2.
Note this board has the otg-vbus connected directly to the 5v-dcc of
the board, so there is no vbus0 regulator, nor vbus0-det.
Signed-off-by: Ralph Benadski <benadski@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the pcDuino 3.
Note this board has the otg-vbus connected directly to the 5v-dcc of
the board, so there is no vbus0 regulator, nor vbus0-det.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.
This commit adds a dts for v4 of the gt90h pcb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add regulator configuration to the pcduino3 dts file.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Removed usb_power_supply node that isn't defined in the DTSI]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a simplefb node for tvencoder / composite-video output, such as found
on the Auxtek-T003 and the CHIP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Colombus development kit uses an optional 2048x1536 edp panel using
an anx9804 parallel lcd to edp converter. The anx9804 chip is controlled
via an i2c bus which is connected to 2 regular gpio pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
-
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UnKL
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.3-rc cycle:
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: fix omap2+ address translation for pbias
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
regulator: pbias: program pbias register offset in pbias driver
ARM: omap2plus_defconfig: Enable MUSB DMA support
ARM: DRA752: Add ID detect for ES2.0
ARM: OMAP3: vc: fix 'or' always true warning
ARM: OMAP2+: Fix booting if no timer parent clock is available
ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>
Added new iio properties which are required for twl4030-charger driver and
allow to use twl4030-madc indirectly.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Move aliases from bcm-cygnus.dtsi back to individual .dts files. Also
clean up the chosen node to have the stdout-path using the proper alias
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
so that they can read the edid of connected displays.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWAdpbAAoJEPOmecmc0R2B9DgH/1Il++FcqJRQfk1HoSEXeD3s
A2PX1eDlE984LcA2G/JQZ10iZxcLx07jg4pxRUcEDJ7iMdFrBFg4B7uHL5iM6kp5
iAhSkRthsuwTpY9ySLe03izjF0a/9+0FvGdG939x7Hlfk4qhtb+ynzvMJcZ9Bs3n
oxvvXqBBkEbK1vnySJkDnDCnK3fRBUse7QRcxKY2YdSYyxdw9Ga51hReF71pyH4u
t7+8+4Pniz68i22YYW/zbGsO79f9tpmT7pisIfNnUOu11gDkL9oX3WkzeJWNh5BC
9guT9CF1c+DLshSWYVDHZ+TCjwVFpgpz3osAKd10FUzWQctU1H/4FGaYviwNILY=
=c2bs
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Add the ddc-i2c-bus reference to the veyron hdmi nodes,
so that they can read the edid of connected displays.
* tag 'v4.3-rockchip32-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: Add ddc i2c reference to veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
STI drm drivers probe and bind using component framework was incorrect.
In addition to drivers fix DT update is needed to make all sub-components
become childs of sti-display-subsystem.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
"ARM: dts: <omap2/omap4/omap5/dra7>: add minimal l4 bus
layout with control module support" moved pbias_regulator dt node
from being a child node of ocp to be the child node of
'syscon'. Since 'syscon' doesn't have the 'ranges' property,
address translation fails while trying to convert the address
to resource. Fix it here by populating 'ranges' property in
syscon dt node.
Fixes: 72b10ac00e ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Fixes: 7415b0b4c6 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Fixes: ed8509eddd ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Fixes: d919501fef ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: fixed omap3 pbias to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes a duplicated pin control causing this error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by regulators:regulator@2; cannot claim for 2184000.usb
imx6q-pinctrl 20e0000.iomuxc: pin-137 (2184000.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp on device 20e0000.iomuxc
imx_usb 2184000.usb: Error applying setting, reverse things
back
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_EIM_D31 already
requested by regulators:regulator@1; cannot claim for 2184200.usb
imx6q-pinctrl 20e0000.iomuxc: pin-52 (2184200.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 52 (MX6Q_PAD_EIM_D31)
from group usbh1grp on device 20e0000.iomuxc
imx_usb 2184200.usb: Error applying setting, reverse things
back
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Fixes: e2047e33f2 ("ARM: dts: add initial Rex Pro board support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The third compatible string "brcm,brcmnand" in bcm-cygnus.dtsi nand node
is incorrect, redundant and should be removed. "brcm,brcmnand" is meant to
be used by STB based Broadcom SoCs. All iProc based SoCs should use
"brcm,nand-iproc".
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch enables touchscreen support on bcm958300k and bcm958305k.
Touchscreen is connected to these boards through the bcm9hmidc daughter
card, and therefore also adding bcm9hmidc.dtsi that describes the
daughter card
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adam Sampson