After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.
This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.
Cc: stable@vger.kernel.org # v3.16+
Fixes: 357b2f3dd9 ("powerpc/eeh: Dump PE location code")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: zhxihu <zhxihu@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For PAE kernels "unsigned long" is not suitable to hold page protection
flags, since _PAGE_NX doesn't fit there. This is the reason for quite a
few W+X pages getting reported as insecure during boot (observed namely
for the entire initrd range).
Fixes: 281d4078be ("x86: Make page cache mode a real type")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <JGross@suse.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/56A7635602000078000CAFF1@prv-mh.provo.novell.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Calling apply_to_page_range with an empty range results in a BUG_ON
from the core code. This can be triggered by trying to load the st_drv
module with CONFIG_DEBUG_SET_MODULE_RONX enabled:
kernel BUG at mm/memory.c:1874!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 3 PID: 1764 Comm: insmod Not tainted 4.5.0-rc1+ #2
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9763b8000 ti: ffffffc975af8000 task.ti: ffffffc975af8000
PC is at apply_to_page_range+0x2cc/0x2d0
LR is at change_memory_common+0x80/0x108
This patch fixes the issue by making change_memory_common (called by the
set_memory_* functions) a NOP when numpages == 0, therefore avoiding the
erroneous call to apply_to_page_range and bringing us into line with x86
and s390.
Cc: <stable@vger.kernel.org>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The kernel now always uses vector registers when available, however KVM
has special logic if support is really enabled for a guest. If support
is disabled, guest_fpregs.fregs will only contain memory for the fpu.
The kernel, however, will store vector registers into that area,
resulting in crazy memory overwrites.
Simply extending that area is not enough, because the format of the
registers also changes. We would have to do additional conversions, making
the code even more complex. Therefore let's directly use one place for
the vector/fpu registers + fpc (in kvm_run). We just have to convert the
data properly when accessing it. This makes current code much easier.
Please note that vector/fpu registers are now always stored to
vcpu->run->s.regs.vrs. Although this data is visible to QEMU and
used for migration, we only guarantee valid values to user space when
KVM_SYNC_VRS is set. As that is only the case when we have vector
register support, we are on the safe side.
Fixes: b5510d9b68 ("s390/fpu: always enable the vector facility if it is available")
Cc: stable@vger.kernel.org # v4.4 d9a3a09af5 s390/kvm: remove dependency on struct save_area definition
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[adopt to d9a3a09af5]
The KVM-VFIO device is used by the QEMU VFIO device. It is used to
record the list of in-use VFIO groups so that KVM can manipulate
them.
While we don't need this on s390 currently, let's try to be like
everyone else.
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
fprs is never freed, therefore resulting in a memory leak if
kvm_vcpu_init() fails or the vcpu is destroyed.
Fixes: 9977e886cb ("s390/kernel: lazy restore fpu registers")
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Since each iomap_entry handles only one bar of one pci function
(even when disjunct ranges of a bar are mapped) the sanity check
in pci_iomap_range is not needed and can be removed.
Also convert the remaining BUG_ONs to WARN_ONs.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We receive special notifications from firmware when an error was detected
and a pci function became unusable. Set the error_state accordingly to give
device drivers a hint that they don't need to try error recovery.
Suggested-by: Alexander Schmidt <alexschm@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the check which bar space we should map to allow available bars only.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 we need to maintain a mapping between iomem addresses
and arch specific function identifiers. Currently the mapping
table is created as such that we could span the whole iomem
address space. Since we can only map each bar space from each
possible function we have an upper bound for the number of
mapping entries.
This reduces the size of the iomap from 256K to less than 4K
(using the defconfig).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Most of the constants defined in pci_io.h depend on each other
and thus can be calculated.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide and use a ZPCI_ADDR macro as the complement of ZPCI_IDX
to get rid of some constants in the code.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ZPCI_IOMAP_MAX_ENTRIES is off by one. Let's adjust this
for the sake of correctness.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 3e89e1c5ea ("hugetlb: make mm and fs code explicitly non-modular")
moves hugetlb_init() from module_init to subsys_initcall.
The hugetlb_init()->hugetlb_register_node() code accesses "node->dev.kobj"
which is initialized in numa_init_late().
Since numa_init_late() is a device_initcall which is called *after*
subsys_initcall the above mentioned patch breaks NUMA on s390.
So fix this and move numa_init_late() to arch_initcall.
Fixes: 3e89e1c5ea ("hugetlb: make mm and fs code explicitly non-modular")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on requests, update our defconfig so that:
- We don't build any modules
- PL031 is enabled (RTC emulated by qemu)
- Xen guest support is enabled
- The Uniphier built-in I2C controller is enabled
- PCI host controller drivers for the various arm64 SoCs are enabled
- Device passthrough works on Seattle using SMMU and VFIO
- The Hisilicon IRQ controller (mbigen) is enabled
Signed-off-by: Will Deacon <will.deacon@arm.com>
GCC6 (and Linaro's 2015.12 snapshot of GCC5) has a new default that uses
adrp/ldr or adrp/add to address literal pools. When CONFIG_ARM64_ERRATUM_843419
is enabled, modules built with this toolchain fail to load:
module libahci: unsupported RELA relocation: 275
This patch fixes the problem by passing '-mpc-relative-literal-loads'
to the compiler.
Cc: stable@vger.kernel.org
Fixes: df057cc7b4 ("arm64: errata: add module build workaround for erratum #843419")
BugLink: http://bugs.launchpad.net/bugs/1533009
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Christophe Lyon <christophe.lyon@linaro.org>
Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By default the aarch64 gcc generates .eh_frame sections. Unlike
.debug_frame sections, the .eh_frame sections are loaded into memory
when the associated code is loaded. On an example kernel being built
with this default the .eh_frame section in vmlinux used an extra 1.7MB
of memory. The x86 disables the creation of the .eh_frame section.
The aarch64 should probably do the same to save some memory.
Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
sh variant of smp_store_mb() calls xchg() on !SMP which is stronger than
implied by both the name and the documentation.
commit 90a3ccb0be ("sh: define __smp_xxx,
fix smp_store_mb for !SMP") was supposed to fix it but
left the bug in place.
Drop smp_store_mb, so that code in asm-generic/barrier.h
will define it correctly depending on CONFIG_SMP.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a73 ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: c43379e150 ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b62 ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This aligns the stack pointer in chacha20_4block_xor_ssse3 to 64 bytes.
Fixes general protection faults and potential kernel panics.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Acked-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch fixes a typo in mm/dump.c:
"MODUELS_END_NR" should be "MODULES_END_NR".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, set_pte_at() only checks the software PTE_WRITE bit for user
mappings when it sets or clears the hardware PTE_RDONLY accordingly. The
kernel ptes are written directly without any modification, relying
solely on the protection bits in macros like PAGE_KERNEL. However,
modifying kernel pte attributes via pte_wrprotect() would be ignored by
set_pte_at(). Since pte_wrprotect() does not set PTE_RDONLY (it only
clears PTE_WRITE), the new permission is not taken into account.
This patch changes set_pte_at() to adjust the read-only permission for
kernel ptes as well. As a side effect, existing PROT_* definitions used
for kernel ioremap*() need to include PTE_DIRTY | PTE_WRITE.
(additionally, white space fix for PTE_KERNEL_ROX)
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Performance Monitors extension is an optional feature of the
AArch64 architecture, therefore, in order to access Performance
Monitors registers safely, the kernel should detect the architected
PMU unit presence through the ID_AA64DFR0_EL1 register PMUVer field
before accessing them.
This patch implements a guard by reading the ID_AA64DFR0_EL1 register
PMUVer field to detect the architected PMU presence and prevent accessing
PMU system registers if the Performance Monitors extension is not
implemented in the core.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 60792ad349 ("arm64: kernel: enforce pmuserenr_el0 initialization and restore")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When switching from the early KASAN shadow region, which maps the
entire shadow space read-write, to the permanent KASAN shadow region,
which uses a zero page to shadow regions that are not subject to
instrumentation, the lowest level table kasan_zero_pte[] may be
reused unmodified, which means that the mappings of the zero page
that it contains will still be read-write.
So update it explicitly to map the zero page read only when we
activate the permanent mapping.
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit e8f3010f73 ("arm64/efi: isolate EFI stub from the kernel
proper") isolated the EFI stub code from the kernel proper by prefixing
all of its symbols with __efistub_, and selectively allowing access to
core kernel symbols from the stub by emitting __efistub_ aliases for
functions and variables that the stub can access legally.
As an unintended side effect, these aliases are emitted into the
kallsyms symbol table, which means they may turn up in backtraces,
e.g.,
...
PC is at __efistub_memset+0x108/0x200
LR is at fixup_init+0x3c/0x48
...
[<ffffff8008328608>] __efistub_memset+0x108/0x200
[<ffffff8008094dcc>] free_initmem+0x2c/0x40
[<ffffff8008645198>] kernel_init+0x20/0xe0
[<ffffff8008085cd0>] ret_from_fork+0x10/0x40
The backtrace in question has nothing to do with the EFI stub, but
simply returns one of the several aliases of memset() that have been
recorded in the kallsyms table. This is undesirable, since it may
suggest to people who are not aware of this that the issue they are
seeing is somehow EFI related.
So hide the __efistub_ aliases from kallsyms, by emitting them as
absolute linker symbols explicitly. The distinction between those
and section relative symbols is completely irrelevant to these
definitions, and to the final link we are performing when these
definitions are being taken into account (the distinction is only
relevant to symbols defined inside a section definition when performing
a partial link), and so the resulting values are identical to the
original ones. Since absolute symbols are ignored by kallsyms, this
will result in these values to be omitted from its symbol table.
After this patch, the backtrace generated from the same address looks
like this:
...
PC is at __memset+0x108/0x200
LR is at fixup_init+0x3c/0x48
...
[<ffffff8008328608>] __memset+0x108/0x200
[<ffffff8008094dcc>] free_initmem+0x2c/0x40
[<ffffff8008645198>] kernel_init+0x20/0xe0
[<ffffff8008085cd0>] ret_from_fork+0x10/0x40
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With commit 90a545e9 (restrict /dev/mem to idle io memory ranges) mapping
rtas_rmo_buf from user space is failing. Hence we are not able to make
RTAS syscall.
This patch calls page_is_rtas_user_buf before calling iomem_is_exclusive
in devmem_is_allowed(). This will allow user space to map rtas_rmo_buf
and we are able to make RTAS syscall.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
CC: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove bcm63xx_nvram_get_psi_size() as it now has no users.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.
Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b9
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.
To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11892/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The first argument to set_except_vector is the ExcCode, which we now
have definitions for. Lets make use of them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11894/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few missing trap codes.
[ralf@linux-mips.org: Drop removal of exception codes. I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11890/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The module init and exit functions have no need to be global, so make
them static.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11889/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.
Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11888/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Export symbols only to GPL modules to match other KVM symbols in
virt/kvm/ and arch/*/kvm/.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11887/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function kvm_mips_host_tlb_inv_index() is unused, so drop it
completely.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.
Lets reunite the DC bit definitions with its friends in mipsregs.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some definitions in the MIPS asm/kvm_host.h are completely unused, so
lets drop them.
MS_TO_NS is no longer used since commit e30492bbe9 ("MIPS: KVM:
Rewrite count/compare timer emulation"). The others don't appear ever to
have been used.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds basic DTS configuration for the PIC32MZDA chip and in turn the
PIC32MZDA Starter Kit.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.
This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12097/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c5a ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: 40e084a506 ("MIPS: Add uprobes support.")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11920/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11925/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11924/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11921/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the CONFIG_MIPS_CMDLINE_EXTEND to CONFIG_MIPS_CMDLINE_DTB_EXTEND
to resolve the EXTEND_WITH_PROM macro.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Fixes: 2024972ef5 ("MIPS: Make the kernel arguments from dtb available")
Reviewed-by: Alexander Sverdlin <alexander.svedlin@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11909/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently assumes that a core will start up in legacy mode
using the exception base provided through the CM GCR registers. If a
core has been configured in hardware to start in EVA mode, these
assumptions will fail.
This patch ensures that secondary cores are initialized to meet these
assumptions.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the description of the microMIPS NOP16 encoding or MM_NOP16, which
is not equivalent to the MIPS16 NOP instruction. This is 0x0c00 and
represents the microMIPS `MOVE16 $0, $0' operation, whereas MIPS16 NOP
is encoded as 0x6500, representing `MOVE $0, $16'.
Also fix a typo in `mm_fp0_format' description.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12177/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove irrelevant content from the description of the emulation frame in
`mips_dsemul', referring to bare-metal configurations. Update the text,
reflecting the change made with commit ba3049ed40 ("MIPS: Switch FPU
emulator trap to BREAK instruction."), where we switched from using an
address error exception on an unaligned access to the use of a BREAK 514
instruction causing a breakpoint exception instead.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12176/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Emulate the microMIPS ADDIUPC instruction directly in `mips_dsemul'. If
executed in the emulation frame, this instruction produces an incorrect
result, because the value of the PC there is not the same as where the
instruction originated.
Reshape code so as to handle all microMIPS cases together.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12175/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Complement commit 102cedc32a ("MIPS: microMIPS: Floating point
support.") which introduced microMIPS FPU emulation, but did not adjust
the encoding of the BREAK instruction used to terminate the branch delay
slot emulation frame. Consequently the execution of any such frame is
indeterminate and, depending on CPU configuration, will result in random
code execution or an offending program being terminated with SIGILL.
This is because the regular MIPS BREAK instruction is encoded with the 0
major and the 0xd minor opcode, however in the microMIPS instruction set
this major/minor opcode pair denotes an encoding reserved for the DSP
ASE. Instead the microMIPS BREAK instruction is encoded with the 0
major and the 0x7 minor opcode.
Use the correct BREAK encoding for microMIPS FPU emulation then.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12174/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct formatting breakage introduced with commit 102cedc32a ("MIPS:
microMIPS: Floating point support."), so that further changes to this
code can be consistent.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix an issue introduced with commit 9ab4471c9f ("MIPS: math-emu:
Correct delay-slot exception propagation") where the emulation of a NOP
instruction signals the need to terminate the emulation loop. This in
turn, if the PC has not changed from the entry to the loop, will cause
the kernel to terminate the program with SIGILL.
Consider this program:
static double div(double d)
{
do
d /= 2.0;
while (d > .5);
return d;
}
int main(int argc, char **argv)
{
return div(argc);
}
which gets compiled to the following binary code:
00400490 <main>:
400490: 44840000 mtc1 a0,$f0
400494: 3c020040 lui v0,0x40
400498: d44207f8 ldc1 $f2,2040(v0)
40049c: 46800021 cvt.d.w $f0,$f0
4004a0: 46220002 mul.d $f0,$f0,$f2
4004a4: 4620103c c.lt.d $f2,$f0
4004a8: 4501fffd bc1t 4004a0 <main+0x10>
4004ac: 00000000 nop
4004b0: 4620000d trunc.w.d $f0,$f0
4004b4: 03e00008 jr ra
4004b8: 44020000 mfc1 v0,$f0
4004bc: 00000000 nop
Where the FPU emulator is used, depending on the number of command-line
arguments this code will either run to completion or terminate with
SIGILL.
If no arguments are specified, then BC1T will not be taken, NOP will not
be emulated and code will complete successfully.
If one argument is specified, then BC1T will be taken once and NOP will
be emulated. At this point the entry PC value will be 0x400498 and the
new PC value, set by `mips_dsemul' will be 0x4004a0, the target of BC1T.
The emulation loop will terminate, but SIGILL will not be issued,
because the PC has changed. The FPU emulator will be entered again and
on the second execution BC1T will not be taken, NOP will not be emulated
and code will complete successfully.
If two or more arguments are specified, then the first execution of BC1T
will proceed as above. Upon reentering the FPU emulator the emulation
loop will continue to BC1T, at which point the branch will be taken and
NOP emulated again. At this point however the entry PC value will be
0x4004a0, the same as the target of BC1T. This will make the emulator
conclude that execution has not advanced and therefore an unsupported
FPU instruction has been encountered, and SIGILL will be sent to the
process.
Fix the problem by extending the internal API of `mips_dsemul', making
it return -1 if no delay slot emulation frame has been made, the
instruction has been handled and execution of the emulation loop needs
to continue as if nothing happened. Remove code from `mips_dsemul' to
reproduce steps made by the emulation loop at the conclusion of each
iteration, as those will be reached normally now. Adjust call sites
accordingly. Document the API.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit be0c37c985 (MIPS: Rearrange PTE bits into fixed positions.)
defines fixed PTE bits for MIPS R2. Then, commit d7b631419b
(MIPS: pgtable-bits: Fix XPA damage to R6 definitions.) adds the MIPS
R6 definitions in the same way as MIPS R2. But some R6 #ifdefs in the
later commit are missing, so in this patch I fix that.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While synchronization, count register will go backwards for the master.
If synchronise_count_master() runs before synchronise_count_slave(),
skew becomes even more. The skew is very harmful for CPU hotplug (CPU0
do synchronization with CPU1, then CPU0 do synchronization with CPU2
and CPU0's count goes backwards, so it will be out of sync with CPU1).
After the commit cf9bfe55f2 (MIPS: Synchronize MIPS count one
CPU at a time), we needn't evaluate count_reference at the beginning of
synchronise_count_master() any more. Thus, we evaluate the initcount (It
seems like count_reference is redundant) in the 2nd loop. Since we write
the count register in the last loop, we don't need additional barriers
(the existing memory barriers are enough).
Moreover, I think we loop 3 times is enough to get a primed instruction
cache, this can also get less skew than looping 5 times.
Comments are also updated in this patch.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/12163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
Merge small final update from Andrew Morton:
- DAX feature work: add fsync/msync support
- kfree cleanup, MAINTAINERS update
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: return arch/sh to maintained state, with new maintainers
tree wide: use kvfree() than conditional kfree()/vfree()
dax: never rely on bh.b_dev being set by get_block()
xfs: call dax_pfn_mkwrite() for DAX fsync/msync
ext4: call dax_pfn_mkwrite() for DAX fsync/msync
ext2: call dax_pfn_mkwrite() for DAX fsync/msync
dax: add support for fsync/sync
mm: add find_get_entries_tag()
dax: support dirty DAX entries in radix tree
pmem: add wb_cache_pmem() to the PMEM API
dax: fix conversion of holes to PMDs
dax: fix NULL pointer dereference in __dax_dbg()
Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in arm-soc
a bit late, which is why we've kept it separate from the other updates
and are sending it separately here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LG3u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
A few fixes for fallout that we didn't catch in time in -next, or smaller
warning fixes that have been discovered since.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PRjJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__arch_wb_cache_pmem() was already an internal implementation detail of
the x86 PMEM API, but this functionality needs to be exported as part of
the general PMEM API to handle the fsync/msync case for DAX mmaps.
One thing worth noting is that we really do want this to be part of the
PMEM API as opposed to a stand-alone function like clflush_cache_range()
because of ordering restrictions. By having wb_cache_pmem() as part of
the PMEM API we can leave it unordered, call it multiple times to write
back large amounts of memory, and then order the multiple calls with a
single wmb_pmem().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 22b1452399.
It was originally sent in an earlier revision of the pfn_t patchset.
Besides being broken, the warning is also fixed by PFN_FLAGS_MASK
casting the PAGE_MASK to an unsigned long.
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12182/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Correct extal1 frequency of armadillo800eva board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YGew
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board
* tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can
now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that
DEBUG_RODATA gets selected by default. This way we can make sure
any related issues are caught early.
And while testing things on various devices, I noticed we're
missing few loadable modules to make things more usable:
- USB Ethernet for smsc75xx, we only have smsc97xx right now
- Basic USB serial drivers for things like ftdi and pl2303 ports
- Blinking leds with pca963x
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text so let's move ppa_zero_params and
ppa_por_params to .data and access them via pointers.
Note that I have not been able to test as we I don't have a HS
omap4 to test with. The code has been changed in similar way as
for omap3 though.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text, so let's move l2_inv_api_params
to .data and access it via a pointer.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't want to write to .text and we can move save_secure_ram_context
into .data as it all gets copied into SRAM anyways.
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org # v4.0+
Fixes: 1e6b48116a ("ARM: mm: allow non-text sections to be
non-executable")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nicolas Ferre