Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.
Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.
To read 4 kB chunk from address 0x400000:
dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1
To write value 0x01020304 to address 0x400400:
echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832
To read 4 KB chunk of memory and then write back after edit:
dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_tx_wep_key_work() acquires conf_mutex, so
cancelling it when conf_mutex is already taken
in ath10k_remove_interface() is incorrect, so
move it outside the lock.
Snippet from the lockdep report:
kernel: ======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.18.0-rc5-wl-debug #34 Tainted: G O
kernel: -------------------------------------------------------
kernel: hostapd/451 is trying to acquire lock:
kernel: ((&arvif->wep_key_work)){+.+...}, at: [<ffffffff810872d5>] flush_work+0x5/0x290
kernel: but task is already holding lock:
kernel: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa0b99f00>] ath10k_remove_interface+0x40/0x290 [ath10k_core]
kernel: which lock already depends on the new lock.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
peer->keys needs to be protected by data_lock
since it is also accessed from the WMI path.
Both install() and clear() routines for peer
keys modify the key contents, so use the data_lock
to avoid races.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When static keys are used in shared WEP, when a
station is associated, message 3 is sent with an
encrypted payload. But, for subsequent
authentications that are triggered without a
deauth, the auth frame is decrypted by the HW.
To handle this, check if the WEP keys have already
been set for the peer and if so, mark the
frame as decrypted. This scenario can happen
when a station changes its default TX key and initiates
a new authentication sequence.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't seem to deilver
management frames with FCS error via WMI so narrow
down the HTT rule to not drop corrupted management
frames.
This basically increases number of frames ath10k
reports while sniffing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When mac80211 requests driver to cancel a hw roc
the driver must not call the expired() callback or
else roc will fail in some cases depending on how
things get scheduled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With P2P concurrency requested hw roc duration
time can be very small. Some firmware revisions
refuse scan requests with too small channel dwell
time.
This prevents messages like, e.g. with connected
STA vif and performing P2P Find:
ath10k_pci 0000:00:05.0: failed to switch to channel for roc scan
ieee80211 phy3: failed to start next HW ROC (-110)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware revisions don't need peer creation
when doing offchannel tx. Earlier revisions would
queue and never release frames without a peer.
This prevent new firmware revisions from stopping
replenishing wmi-htc tx credits and improves
reliability of offchannel tx which would sometimes
silently fail.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Comment was out-of-date. The headroom is no longer
necessary because HTT Tx fragment list is stored
in dma pool item associated with each sk_buff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When re-associating a station, the nss was set back to
maximum value even if user had configured small number
of tx chains. So, pay attention to user's config in
this case as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It appears it takes more than just setting the
hardware's chainmask to make things work well. Without
this patch, a vdev would only use 1x1 rates when chainmask
was set to 0x3.
Setting the 'nss' (number of spatial streams) on the vdev
helps the firmware's rate-control algorithm work properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The existing order of steps when starting the PCI devices works for
2.4G devices, but fails to initialize the 5G section of the RTL8821AE
hardware.
This patch is needed to fix the regression reported in Bug #88811
(https://bugzilla.kernel.org/show_bug.cgi?id=88811).
Reported-by: Valerio Passini <valerio.passini@unicam.it>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The changes associated with moving this driver from staging to the regular
tree missed one section setting the allowable rates for the 5GHz band.
This patch is needed to fix the regression reported in Bug #88811
(https://bugzilla.kernel.org/show_bug.cgi?id=88811).
Reported-by: Valerio Passini <valerio.passini@unicam.it>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Valerio Passini <valerio.passini@unicam.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ACK status (0/1) for ACTION frames is informed to cfg80211. We
will extend existing logic used for EAPOL frames. The cfg80211
API is different here. Also, we need to explicitly free cloned
skb.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware notifies the driver through event if EAPOL data packet
has been acked or not. We will inform this status to userspace
listening on a socket.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had introduced delay main work logic to avoid processing
interrupts when Rx pending packet count reaches high threshold.
interrupt processing is restarted later when packet count
reduces lower threashold. This helped to reduce unnecessary
overhead and improve throughput for SD and PCIe chipsets.
As there are no interrupts for USB, we will skip this logic for
USB chipsets.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds missing endian conversion for beacon size while
processing scan response.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes following sparse warnings:
drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16
drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add TPC capability to TX descriptor path. Cap per-packet TX power according to
TX power per-rate tables. Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver has sent a join iovar to the firmware it waits
for the events to report result of the connection. However, the
wpa_supplicant will request a .disconnect() after a timeout. So
upon calling .disconnect() the interface state may still be
CONNECTING. Clear the CONNECTING bit as well.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the Makefile for this driver, the wrong Kconfig option is used
to trigger the compilation of the object file. This leads to the
driver only being included into the kernel when both CONFIG_RTL8821AE
and CONFIG_RTL8192AE are set to "y".
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In four of the rtlwifi drivers, the Makefile contains superfluous
statements indicating the compilation of the driver as an LKM
regardless of the corresponding Kconfig option.
If the corresponding option is set to 'y', the build system will then
see the object file in obj-m and obj-y, which leads to a compilation
as a built-in only. Even though this leads to the desired behavior,
the unconditional appearance in obj-m is confusing for someone reading
the Makefile.
This patch removes the superfluous Makefile statements.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For FCC and JP, in one of the radar patterns, PPB and PRF seems to be
interchanged leading to frequent incorrect radar detections.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb gadget driver net2280 has exported a header file with the
register definition of the net2280 chip.
Remove the custom/duplicated header file in favor of that header file
in include/linux
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX
filter configuration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a static checker warning:
drivers/net/wireless/brcm80211/brcmfmac/cfg80211.c:2965
brcmf_cfg80211_set_pmksa()
warn: can 'pmkid_len' be negative?
The answer to the question above is likely no so changing its
type to unsigned is sufficient.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rtbg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c17aa52c5b.
It was wrong, IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ
already implies that 160 MHz is supported, as it isn't a bitmap
but rather a value in a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are not many of these messages producted by the
firmware, but they are generally fairly useful, so make it easy to print them
with a separate debug level.
kvalo: fix commit log, rename debug level
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
- Use config symbol defined in the driver instead of arch specific one for
conditional compilation.
- Rename the ATHEROS_AR231X config symbol to ATH25.
- Fix include (ar231x_platform.h -> ath25_platform.h).
- Some of AR231x SoCs (e.g. AR2315) have PCI bus support, so remove !PCI
dependency, which block AHB support build.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 093ec3c533.
AHB bus code has been removed, since we did not have support Atheros
AR231x SoC, required for building the AHB version of ath5k. Now that
support WiSoC chips added we can restore functionality back.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8247/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add suspend/resume trans ops that will be called from
mac80211's suspend/resume ops.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest. For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status. This will allow netdetect to reuse the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed. To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add the net detect WoWLAN flag to indicate support and use the
nd_config from the WoWLAN configuration to start net detect, if it is
set. The WoWLAN configuration takes precedence over the debugfs
configuration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When another vif is also running during a channel switch, we need to
use a session protection when we move to the new channel, so that we
don't miss the beacons. Without this, sometimes the other vif
repeatedly gets time exactly when we should be hearing the beacons,
preventing channel switch from completing. Adding a session
protection that lasts from the moment the channel changes until 2
TBTTs later, ensures that we will hear the beacons on the destination
channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
If setting the CSA time event fails, we must clear the TE data,
otherwise we'll try to remove it when, for instance, a disconnection
occurs, causing a SYSASSERT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
After a channel switch, transmission on the new channel is only
started once we see a beacon on it. Thus, beacon filtering needs to
be disabled during channel switch so that mac80211 receives this
beacon and finishes the process.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We need to call ieee80211_chswitch_done() ourselves just when the
absence TE started, so we perform the actual context switch early
enough. To do so, add a dummy channel_switch op, which will cause
mac80211 to skip the countdown timer and allow us to call
ieee80211_chswitch_done() to complete the operation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that mac80211 waits for the first beacon on the new channel before
calling post_channel_switch, the reconfiguration of the firmware
should be done in the post_channel_switch operation instead of when
assigning the vif to the new context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Instead of using a hardcoded number of TUs before beacon 0 as the time
to start the absence and actual channel switch, calculate it in
relation to the beacon interval. We use 10 TUs + beacon interval
before beacon 0 to target a bit before beacon 1. This gives us enough
time to switch to the new channel before the AP/GO switches.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add an absent time event when pre_channel_switch is called and use the
time event started indication to set the disable_tx bit instead of
doing it in unassign_vif(). This is done so that the firmware queues
are stopped before the actual switch takes place to avoid losing
packets while the AP/GO is performing its actual switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that all CSA flows are using the switch_vif_chanctx op, we can
rely on the switching_chanctx boolean that is passed to the
__iwl_mvm_assign_vif_chanctx() and __iwl_mvm_unassign_vif_chanctx()
functions to decide whether the context switch flows need to be
executed. In this way we make the chanctx switch flow more generic,
without having to rely on the csa_active flag being set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Disable PS when pre_channel_switch is called and add the
post_channel_switch operation to re-enable PS when the channel switch
is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The spec requires to decrement the CSA counters based on TBTT,
regardless if the beacon was actually transmitted. Previously, the fw
would send beacon notifications only for successfully transmitted
beacons. This behavior resulted in inaccurate CSA countdown. In order
to address this issue, the fw was changed to send beacon
notifications also for not transmitted beacons. Such notifications
have TX_STATUS_INTERNAL_ABORT (0x92).
Don't start the CSA countdown before first successfully transmitted
beacon, in order to guarantee that the CSA is announced for a
required period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We have code to recover and go back to the original channel context if
something fails in the middle of switch_vif_chanctx, but we return the
error code of the recover calls instead of the original code, so if
the recovery succeeds, we will return 0 (success). Fix this by not
assigning the return value of the recovery calls to ret.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add support to reassign vif in switch_vif_chanctx. This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well. Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared. To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP. Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.
Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
A new callback has been added to prepare the device for a channel
switch. Use the new callback instead of the old channel_switch_beacon
operation.
This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.
Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When adding a TDLS station, allocate 4 new queues for it. Configure them
to FW and enable them. On station removal, drain the queues if needed
and disable them when empty.
Make sure to flush all packets in the private queues of TDLS stations in
the mac80211 flush() callback.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS peers are present the FW will send packets on a dedicated
TID vs. the peer when performing TDLS channel-switches. The driver
configures the TID on connection to the peer and the FW is responsible
for maintaining the state of QoS seqno and PN/IV for encryption.
If the FW asserts, the driver cannot correctly reconfigure the starting
seqno/PN to the reloaded FW, thus forcing us to reconnect the peer.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TDLS stations will have private queues, so consider them as well when
allocating a new one. Consolidate the HW-queue iterating code into
a single exported function, to be used by the TDLS code in the future.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send a dedicated TDLS_CONFIG command when a TDLS peer joins/leaves. The
fields for the command are mostly place-holders, as most of the FW
functionality is not implemented. In the future the dedicated FW TID
will be used for channel-switching and buffer-sta functionality.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a channel-switch command and a switch-start notification. Also add a
FW TLV bit indicating TDLS channel switching support.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver/FW combination now support TDLS.
Check the FW support with the TLV bit.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header including crypto (assuming the packet isn't
short enough to be in there completely.) This is fine, but in
ieee80211_data_to_8023() we later unconditionally pull 8 more
bytes for the SNAP header and ethertype field (except for mesh
or 4-addr, where it's even more, but we don't care as much about
them).
Avoid the additional later pull by pulling in those 8 bytes here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header (assuming the packet isn't short enough to
be in there completely.) This is fine, but in many cases we'll
pull in the crypto headers pretty much immediately afterwards,
so to avoid that pull in the crypto header early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of building the rx_status on the stack and then
copying it to the skb, allocate the skb a bit earlier
and then build the rx_status in place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the original driver, we decided to not implement WEP RX hardware
offload because of a quirk with the firmware API - it allows setting
global WEP keys that then get used for all virtual interfaces, which
is clearly wrong if more than one exists, and it allows setting per-
station keys but then separates multicast and unicast keys.
In order to implement WEP RX hardware offload, work around these
limitations by uploading each WEP key twice, once as multicast and
once as unicast, but point them both to the same key slot (offset)
and use the same key material so the slot overwrite on the second
upload doesn't actually change anything. Upon removal, also remove
the key twice so the station no longer references it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the key add/remove functions to be able to reuse parts
of them later for RX WEP keys, which need to be uploaded twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flow that handles the requests to cancel the roc time event,
that has been triggered via the aux framework.
The roc for bss is different than the roc for p2p devices, and is done
via the aux framework using the aux queue, thus requires a different flow
to cancel the time event.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove warning on scan complete with unknown ID, since this
scan could be already cleared in abort flow.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ssid_bitmap should be unsigned, though it doesn't matter
much as the high bits aren't used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Identify 7265-D devices using the hardware revision (they have the
same PCI IDs as 7265) and change the configuration for them taking
the differences (currently only the firmware image) into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Toggle the LMPM_CHICK register when writing chunks into the FW's extended
SRAM. This tells the FW to put the chunk into a different memory space.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no reason to pass every 50th beacon if
nothing was changed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of allocating nd_ies separately, make it part of the iwl_mvm
structure so it's easier to handle its lifetime.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We were toggling the wrong bit when we reset the device,
fix that. Moreover, since the reset can take time, we need
to wait before we set the rfkill interrupt. Not doing so
can be racy since the driver is enabling the rfkill
interrupt while the device is resetting which will clear
all the registers including the CSR_INT_MASK.
This can basically lead to a situation where we don't
enable the rfkill interrupt. If that happens, the user will
not be able to re-enable the device when de-asserting
rfkill.
This scenario happened to the submitter of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For background and scheduled scan, using the new unified scan API,
support random MAC address scanning.
Unfortunately, the firmware right now doesn't support randomising
itself, so for now do it on the host - we'll change this once the
firmware supports randomising the address for each scan iteration
using the address/mask.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC TLV bit may be on in FWs that support UMAC scan; so check
for UMAC TLV bit first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The fw now indicates missing BA with ampdu_ack_len=0.
This will make the whole aggregation being marked
as failed, although it's most likely not the case (and
only the BA itself was failed).
Consider this case as a single tx failure.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The TTC and RRC features are supported by the newer
firmwares. It allows to reach better overall WiFi and BT
performance. When the RRC is enabled, we don't need to force
the AP to send SISO frames, but it can keeps sending MIMO
frames.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This API uses second CPU scan commands, and can support multiple
simultaneous scans.
Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.
New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver must set the keep alive period regardless of power
management state. The keep alive period must be greater or equal to
both the NIC's maximum sleep period, and the listen interval.
However, we were confusing time units (TU) and msec, so fix that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler suffers from false wake-up on 500 time units.
that is if the dtim interval exceeds 500 time units, the fw wakes up,
understands that the next wake-up event is still ahead, and if this event
is more than 10msec in the future - goes back to sleep, otherwise - stay
awake. For example, say that the beacon interval is 101 and the dtim
period is 5, the dtim interval is 101 x 5 = 505, and we will stay awake
for those extra 5msec.
So on the one hand the dtim interval should be congruent to the beacon
interval times the dtim period, and on the other should minimize
the false wake-ups event.
This change applies only to D0/D3 power modes.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The deferred d0i3 exit is currently implemented in the
resume op, which is called when mac80211 starts its
resume process.
However, mac80211 still doesn't handle frames at this stage,
which results in frames being dropped.
Move the deferred d0i3 handling to the reconfig_complete
callback, in order to make sure mac80211 is fully available
at this point.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the corresponding mac80211 patch, we can now report the airtime
used for each transmitted packet and mac80211 will be able to implement
WMM-AC with that information.
To support WMM-AC in the driver then, report the airtime and advertise
support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add two new parameters to iwl_cfg:
max_ht_ampdu_exponent and max_vht_ampdu_exponent.
These parameters, if set, will set new values to the maximum of
HT and VHT A-MPDU exponent for the A-MPDU length exponent.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since it's too complicated for the fw to insert a DS Parameter Set
element in the middle of the frame, it was decided that it should be
done by the host. The fw will only parse the frame and update the
current channel field.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A properly set alpha2 value consists of two chars that both contain
letters or digits. If no value is set, both chars keep their initial
value zero. Therefore do not send the alpha2 parameter to user space
if either of the characters has been left at its initial zero value.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adds new VID/PID for the Marvell 88W8766. The kernel currently only supports
the device as PCI, but it is also available using USB. An example of a device
delivered with the 88W8766 as USB is the Globalscale Mirabox.
TX buffer size is set to driver default (2K), as we do not know the firmware
requirement.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions brcmu_pkt_buf_free_skb() and release_firmware() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).
Cc: stable@vger.kernel.org # v3.17
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmented Rx wasn't reporting everything. With
the reworked Rx code it's very easy to fix it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it more in line with the new Rx path.
It also makes the code more reusable because Rx
descriptor is more accessible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original fix has been moved into a different
place in the code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This creates a single, common path for MSDU,
A-MSDU and fragmented Rx.
Hopefully this will make it easier to understand
Rx path and make it easier to work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the rx_confused be handled by the rx
indication handlers instead of the buffer popping
function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since htt_rx_mpdu_status isn't used anymore
(instead attention flags are used) simplify the
loop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using manual sk_buff linking via ->next
use sk_buff_head. It's more robust, cleaner and
there's plenty of helper functions in kernel
already to manage sk_buff_head.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
currently ath9k_common depends on this components.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HWSIM_CMD_GET_RADIO returns information about a specific radio id or
all of them in response to a dump. Create the netlink skb or use the
one provided by the dump functionality. Use the existing attribute
appending function to fill in the same attributes when creating a
new hwsim radio.
Save alpha2 and struct ieee80211_regdomain in the hwsim data or else
they will be lost in the depths of regulatory infrastructure.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out netlink message attribute appending in order to reuse it
with later code. As a result move netlink skb allocation to the
calling function.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hwname will always be set if idx is negative (as it's
a u32 read into an s64 it can't overflow either) so we can
remove the unnecessary check for hwname being non-NULL.
This was reported by smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can always know the hwname of the radio so use the value
from wiphy.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for scanning with random MAC address for
both software and hardware scan.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in some mwifiex changes that further patches will
need to work on top to not cause merge conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.
This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.
But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.
The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.
Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.
So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.
This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n
and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.
So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.
Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.
Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.
To record tx ieee80211 headers
trace-cmd record -e ath10k_tx_hdr
To record complete packets
trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Yanbo Li