When PF responds to the VF requests it also cleans the HW-channel
indication in firmware to allow further VF messages to arrive,
but the order currently applied is wrong -
The PF is copying by DMAE the response the VF is polling on for
completion, and only afterwards sets the HW-channel to ready state.
This creates a race condition where the VF would be able to send
an additional message to the PF before the channel would get ready
again, causing the firmware to consider the VF as malicious.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is considered malicious, driver handling of the VF
FLR flow would clean said indication - but not if the FLR is
part of an sriov-disable flow.
That leads to further issues, as PF wouldn't re-enable the
previously malicious VF when sriov is re-enabled.
No reason for that - simply clean malicious indications in
the sriov-disable flow as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently logging errors when communicating
with their PFs in a too-low verbosity that wouldn't
be shown by default. As timeouts and failed commands
are crucial for VF operability, make them appear by
default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rhashtable_lookup_get_insert_fast for fixed keys, similar to
rhashtable_lookup_get_insert_key for explicit keys.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to support host<->firmware command return value.
Fix for vf mac addr state command.
1. Added support for firmware commands to return a value:
- previously, the returned code overlapped with host codes, thus
commands were only returning 0 (success) or -1 (interpreted as
timeout)
- per 'response_manager.h', the error codes are split into two fields
(major/minor) now, firmware commands are grouped into their own
'major' group, separate from the host's 'major' group, which allow f/w
commands to return any 16-bit value
2. The command to set vf mac addr was logging a success message even if
command failed. Now command uses a callback function to log the status
message.
3. The command to set vf mac addr was not logging a message when set via
the host 'ip' command. Now, the callback function will log an
appropriate message.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen says:
====================
ibmvnic: Initialization fixes and improvements
These patches resolve issues with the ibmvnic initialization process.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic device we need to release the resources used
in communicating to the virtual I/O server. These need to be
re-negotiated with the server at open time.
This patch moves the releasing of resources a separate routine
and updates the open and close handlers to release all resources at
close and re-negotiate and allocate these resources at open.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intialization of the ibmvnic driver with respect to the virtual
server it connects to should be moved to its own routine. This will
alolow the driver to initiate this process from places outside of
the drivers probe routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that handles login and renegotiation of ibmvnic
capabilities to its own routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC server expects LINK_STATE_UP to be sent within 30s of the login. If we
exceed the timeout, VNIC server will attempt to fail over. Since time
between probe and open of the device is indeterminate, move login and queue
negotiation into ibmvnic open so we can guarantee that login and sending
LINK_STATE_UP occur within the 30s window.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gem_begin_auto_negotiation dereference
the pointer ep before testing if it's null. This
patch add a check on ep before dereferencing it.
Fixes: 92552fdda5 ("net: sun: sungem: use new api
ethtool_{get|set}_link_ksettings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timeout error message in lio_process_ordered_list(). Add host failure
status in existing error message in if_cfg_callback().
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code duplicated in PF and VF; define that code once only in a common
header file included by PF and VF.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joao Pinto says:
====================
net: stmmac: adding multiple buffers and routing
As agreed with David Miller, this patch-set is the third and last to enable
multiple queues in stmmac.
This third one focuses on:
a) Enable multiple buffering to the driver and queue independent data
b) Configuration of RX and TX queues' priority
c) Configuration of RX queues' routing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX queues' routing.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX and TX queues' priority.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates 2 new structures (stmmac_tx_queue and stmmac_rx_queue)
in include/linux/stmmac.h, enabling that each RX and TX queue has its
own buffers and data.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy() instead of memcpy() to set netdev->dev_addr (which
is 2-byte aligned).
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: small driver update
Contains two cleanup patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the default case for matchall offload with what's there
for flower.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the struct representing router interface "mlxsw_sp_rif"
is reffered as "r" in various places in the driver. Furthermore it
contains a member which specify the index which is called "rif".
This patch change "r" to "rif" and "rif" to "rif_index".
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes says:
====================
net: usbnet: move to new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated. On usbnet, it
was often implemented with usbnet_{get|set}_settings.
In this series, I add usbnet_{get|set}_link_ksettings
in the first patch, then I update all the driver to
use this new api, and in the last patch I remove the
old api usbnet_{get|set}_settings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function usbnet_{get|set}_settings is no longer used,
so we remove it.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: poma <poma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We add the new api {get|set}_link_ksettings to this driver.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__bcmgenet_tx_reclaim() is currently summing TX bytes/packets in a way
that is not SMP friendly, mutliples CPUs could run
__bcmgenet_tx_reclaim() independently and still update stats->tx_bytes
and stats->tx_packets, cloberring the other CPUs statistics.
Fix this by tracking per RX and TX rings the number of bytes, packets,
dropped and errors statistics, and provide a bcmgenet_get_stats()
function which aggregates everything and returns a consistent output.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ECMP hash policy choice via a new sysctl
called fib_multipath_hash_policy and also adds support for L4 hashes.
The current values for fib_multipath_hash_policy are:
0 - layer 3 (default)
1 - layer 4
If there's an skb hash already set and it matches the chosen policy then it
will be used instead of being calculated (currently only for L4).
In L3 mode we always calculate the hash due to the ICMP error special
case, the flow dissector's field consistentification should handle the
address order thus we can remove the address reversals.
If the skb is provided we always use it for the hash calculation,
otherwise we fallback to fl4, that is if skb is NULL fl4 has to be set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wanted_features is a set of features which have to be enabled if a
hardware allows that.
Currently when a vlan device is created, its wanted_features is set to
current features of its base device.
The problem is that the base device can get new features and they are
not propagated to vlan-s of this device.
If we look at bonding devices, they doesn't have this problem and this
patch suggests to fix this issue by the same way how it works for bonding
devices.
We meet this problem, when we try to create a vlan device over a bonding
device. When a system are booting, real devices require time to be
initialized, so bonding devices created without slaves, then vlan
devices are created and only then ethernet devices are added to the
bonding device. As a result we have vlan devices with disabled
scatter-gather.
* create a bonding device
$ ip link add bond0 type bond
$ ethtool -k bond0 | grep scatter
scatter-gather: off
tx-scatter-gather: off [requested on]
tx-scatter-gather-fraglist: off [requested on]
* create a vlan device
$ ip link add link bond0 name bond0.10 type vlan id 10
$ ethtool -k bond0.10 | grep scatter
scatter-gather: off
tx-scatter-gather: off
tx-scatter-gather-fraglist: off
* Add a slave device to bond0
$ ip link set dev eth0 master bond0
And now we can see that the bond0 device has got the scatter-gather
feature, but the bond0.10 hasn't got it.
[root@laptop linux-task-diag]# ethtool -k bond0 | grep scatter
scatter-gather: on
tx-scatter-gather: on
tx-scatter-gather-fraglist: on
[root@laptop linux-task-diag]# ethtool -k bond0.10 | grep scatter
scatter-gather: off
tx-scatter-gather: off
tx-scatter-gather-fraglist: off
With this patch the vlan device will get all new features from the
bonding device.
Here is a call trace how features which are set in this patch reach
dev->wanted_features.
register_netdevice
vlan_dev_init
...
dev->hw_features = NETIF_F_HW_CSUM | NETIF_F_SG |
NETIF_F_FRAGLIST | NETIF_F_GSO_SOFTWARE |
NETIF_F_HIGHDMA | NETIF_F_SCTP_CRC |
NETIF_F_ALL_FCOE;
dev->features |= dev->hw_features;
...
dev->wanted_features = dev->features & dev->hw_features;
__netdev_update_features(dev);
vlan_dev_fix_features
...
Cc: Alexey Kuznetsov <kuznet@virtuozzo.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following checkpatch.pl recommendations (which include
replacing with <linux/io.h> the <asm/io.h>, since linux/io.h includes
it).
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables developing code that uses SOF_TIMESTAMPING_TX_SOFTWARE
by using localhost addresses (without needing to send packets outside),
as well as enabling unit and functional testing of TX timestamping code
without needing hardware support or network access.
It also fulfills the expectation of software network devices supporting
software-based timestamping.
Tested on qemu using txtimestamping.c from the kernel selftests, and
ethtool -T.
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-20
This series contains updates to i40e and i40evf only.
Philippe Reynes updates i40e and i40evf to use the new ethtool API for
{get|set}_link_ksettings.
Jake provides the remaining patches in the series, starting with a fix
for i40e where the firmware expected the port numbers for the offloaded
UDP tunnels in Little Endian format and we were sending them in Big Endian
format which put the wrong port number to be put in the UDP tunnel list.
Changed the driver to use __be32 values instead of arrays for
(src|dst)_ip. Refactored the exit flow of i40e_add_fdir_ethtool() which
removes the dependency on having a non-zero return value. Fixed a memory
leak by running kfree() and returning immediately when we fail to add
flow director filter. Fixed a potential issue where could update the
filter count without actually succeeding in adding a filter, by moving
the ATR exit check to after we have sent the TCP/IPv4 filter to the ring
successfully. Ensures that the fd_tcp_rule count is reset to 0, before
we reprogram the filters so that we do not end up with a stale count
which does not correctly reflect the number of programmed filters. Added
a check whether we have TCP/IPv4 filters before re-enabling ATR after
flushing and replaying FDIR filters. Added counters for each filter
type in preparation for adding code to properly check the mask value.
Fixed potential issues by explicitly checking the flow type at the
start of i40e_add_fdir_ethtool(). To avoid possible memory leaks,
we now unconditionally delete the old filter, even if it is identical to
the new filter and ensures will always update the filters as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your
net-next tree. A couple of new features for nf_tables, and unsorted
cleanups and incremental updates for the Netfilter tree. More
specifically, they are:
1) Allow to check for TCP option presence via nft_exthdr, patch
from Phil Sutter.
2) Add symmetric hash support to nft_hash, from Laura Garcia Liebana.
3) Use pr_cont() in ebt_log, from Joe Perches.
4) Remove some dead code in arp_tables reported via static analysis
tool, from Colin Ian King.
5) Consolidate nf_tables expression validation, from Liping Zhang.
6) Consolidate set lookup via nft_set_lookup().
7) Remove unnecessary rcu read lock side in bridge netfilter, from
Florian Westphal.
8) Remove unused variable in nf_reject_ipv4, from Tahee Yoo.
9) Pass nft_ctx struct to object initialization indirections, from
Florian Westphal.
10) Add code to integrate conntrack helper into nf_tables, also from
Florian.
11) Allow to check if interface index or name exists via
NFTA_FIB_F_PRESENT, from Phil Sutter.
12) Simplify resolve_normal_ct(), from Florian.
13) Use per-limit spinlock in nft_limit and xt_limit, from Liping Zhang.
14) Use rwlock in nft_set_rbtree set, also from Liping Zhang.
15) One patch to remove a useless printk at netns init path in ipvs,
and several patches to document IPVS knobs.
16) Use refcount_t for reference counter in the Netfilter/IPVS code,
from Elena Reshetova.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-03-17
This series contains updates to mainly igb, with one fix for ixgbe.
Alex does all the changes in the series, starting with adding support
for DMA_ATTR_WEAK_ORDERING to improve performance on some platforms.
Modified igb to use the length of the packet instead of the DD status
bit to determine if a new descriptor is ready to be processed. Modified
the driver to only go through the region in the receive ring that was
designated to be cleaned up, instead of going through the entire ring
on cleanup. Cleaned up the transmit side, by clearing the transmit
buffer_info only when resetting the rings. Added a new upper limit for
receive, which is based on the size of a 2K buffer minus padding, which
will allow us to support build_skb going forward. Fixed ethtool testing
to only sync on the size of the frame that is being tested, instead of
the entire receive buffer. Updated the handling of page addresses to
always use a void pointer with the consistent name of "va" to indicate
that we are working with a virtual address. Added a "chicken bit" so
that we can turn off the new receive allocation feature, in the case
where we need to fallback to the legacy receive path. Added support for
using 3K buffers in order 1 pages the same way we were using 2K buffers
in 4K pages. Added support for padding packet, since we limit the size
of the frame, we are able to write to an offset within the buffer instead
of having to write at the very start of the buffer. This allows us to
leaving padding room for things like supporting XDP in the future.
Refactored the receive buffer page management, since there are 2-3 paths
that can be taken depending on what receive modes are enabled, so to
improve maintainability, break out the common bits into their own
functions. Add support for build_skb, again. Lastly, fixed a typo in
igb and ixgbe code comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mintz, Yuval