We only want use the address of the LLI pointer when locating the
corresponding structure in memory, so clear the master bus selection
bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tight loops should use cpu_relax() to allow CPUs to reduce power
consumption while waiting for events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate duplicated channel release code into release_phy_channel()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate code which allocates and initializes txds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid using 'void *' struct fields when the structs are not defined
in linux/amba/pl08x.h - instead, forward declare the struct names, and
use these instead. This ensures we have proper typechecking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should never modify the vendor data structure so make it const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The driver already won't initialize a channel with a circular buffer;
the check in pl08x_prep_channel_resources() sees to that. Remove
circular buffer support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The tasklet always is initialized with a non-NULL data argument. It
is not possible for it to be called with a NULL data argument (unless
something is very wrong in the tasklet code - in which case lots of
stuff will break). Therefore, as plchan can never be NULL, remove
this unnecessary BUG check.
In pl08x_tasklet(), we've already dereferenced plchan->at, so it can't
be NULL here. Remove this unnecessary BUG check.
pl08x_fill_llis_for_desc() and pl08x_free_txd() are always called with
a non-NULL txd argument - either as a consequence of the code paths or
as a result of other checks already in place. We don't need to repeat
the non-NULL check in these functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We don't need to include linux/pci.h as we aren't a PCI driver. We
aren't doing any processor specific functions, so asm/processor.h is
not required. asm/cacheflush.h shouldn't be used, we have the DMA API
for this. DMA interfaces aren't required as we're only implementing
the dmaengine API and not a platform-private DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A driver which emits both decimal and hex numbers in its printk
creates confusion as to what is what. Prefix hex numbers with 0x.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Include the revision number of the PL08x primecell in the boot-time
printk to allow proper identification of the peripheral. Reformat
the announcement printk format reflect what we do for other primecell
drivers - generally "PLXXX revX at 0xNNNNNNNN irq X".
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Explain the two flow control methods which the PL08x implements, along
with the problem which peripheral flow control presents. This helps
people understand why we are unable to use these DMA controllers with
(eg) the MMCI.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/amba-pl08x.c:1895:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:1903:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:513:6: warning: symbol 'pl08x_choose_master_bus' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:604:5: warning: symbol 'pl08x_fill_llis_for_desc' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:1442:32: warning: symbol 'pl08x_prep_slave_sg' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trying to disable a tasklet while holding a spinlock which the tasklet
will take is a recipe for deadlock - tasklet_disable() will wait for the
tasklet to finish running, which it will never do. In any case, there
is not a corresponding tasklet_enable(), so once the tasklet is disabled,
it will never run again until reboot.
It's safe to just remove the tasklet_disable() as we remove all current
and pending descriptors before releasing this spinlock. This means that
the tasklet will find no remaining work if it subsequently runs.
The only remaining issue is that the callback for an already submitted
txd may be in progress, or even called after terminate_all() returns.
There's not much that can be done about that as waiting for the callback
to complete before returning will also lead to deadlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pl08x_issue_pending() returns with the spinlock locked and interrupts
disabled if the channel is waiting for a physical DMA to become free.
This is wrong - especially as pl08x_issue_pending() is an API function
as it leads to deadlocks. Fix it to always return with the spinlock
unlocked.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we fail to allocate the LLI, the prep_* function will return NULL.
However, the TXD we allocated will not be placed on any list, nor
will it be freed - we'll just drop all references to it. Make sure
we free it rather than leaking TXDs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tasklets are run from an interruptible context. The slave DMA functions
can be called from within IRQ handlers. Taking the spinlock without
disabling interrupts allows an interrupt handler to run, which may try
to take the spinlock again, resulting in deadlock. Fix this by using
the irqsave spinlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The last_issued variable uses an atomic type, which is only
incremented inside a protected region, and then read. Everywhere else
only reads the value, so it isn't using atomic_t correctly, and it
doesn't even need to. Moreover, the DMA engine code provides us with
a variable for this already - chan.cookie. Use chan.cookie instead.
Also, avoid negative dma_cookie_t values - negative returns from
tx_submit() mean failure, yet in reality we always succeed. Restart
from cookie 1, just like other DMA engine drivers do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If maxburst was passed in as zero, we would overflow the burst_sizes[]
array. Fix this by checking for this condition, and defaulting to
single transfer 'bursts'.
Improve the readability of the loop using a for() loop rather than
a while() loop with the iterator initialized far from the loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Correct mis-spellings in comments and printk strings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The maximum transfer size of the stedma40 is (64k-1) x data-width.
If the transfer size of one element exceeds this limit
the job is split up and sent as linked transfer.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: provide dummy functions for DMA_ENGINE=n
mv_xor: fix race in tasklet function
use mv_xor_slot_cleanup() instead of __mv_xor_slot_cleanup() as the former function
aquires the spin lock that needed to protect the drivers data.
Cc: <stable@kernel.org>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently completed descriptors are processed in the tasklet. This can
lead to dead lock in case of CONFIG_NET_DMA enabled (new requests are
submitted from softirq context and dma_memcpy_to_iovec() busy loops until
the requests is submitted). To prevent this we should process completed
descriptors from the allocation failure path in prepare_memcpy too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
MPC8308 has pretty much the same DMA controller as MPC5121 and
this patch adds support for MPC8308 to the mpc512x_dma driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current code clears interrupt active status _after_ submitting new
transfers. This leaves a possibility of clearing the interrupt for this
new transfer (if it is triggered fast enough) and thus lose this
interrupt. We want to clear interrupt active status _before_ new
transfers is submitted and for current channel only.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While testing mpc512x-dma driver with dmatest module I've found that
I can hang the mpc512x-dma issuing request from multiple threads to
the single channel.
insmod dmatest.ko max_channels=1 threads_per_chan=16
After investigating this case I've managed to find that this happens
if and only if we have more than one queued requests.
In this case the driver tries to make use of hardware scatter/gather
functionality. I've found two problems with scatter/gather:
1. When TCD is copied form RAM to the TCD register space with memcpy_io()
e_sg bit eventually gets cleared. This results in only first TCD being
executed. I've added setting of e_sg bit explicitly in the TCD registers.
BTW, what is the correct way to do this? (How can I use setbits with bitfield
structure?) After that hardware loads consecutive TCDs and we hit the
second issue.
2. Existing code clears int_maj bit in the last TCD so we never get
an interrupt on transfer completion.
With these fixes my tests with many threads of single channel succeed but
tests that use many channels simultaneously still don't work reliable.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Presently DMA transfers are interrupted and aborted by the NMI. This
implements some basic logic for more gracefully handling and clearing
each controller's NMIF flag via the NMI die chain, needed to resume
transfers post-NMI.
Reported-by: Michael Szafranek <Michael.Szafranek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Buffer transfer size is the number of transfers to be performed in
relation with the width of the _source_ interface.
So in the DMA_FROM_DEVICE case, it should be the register width that
should be taken into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixed fsl dma slow issue by initializing dma mode register with
bandwidth control. It boosts dma performance and should works
with 85xx board.
Signed-off-by: Forrest Shi <b29237@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The firmware framework gets initialized during fs_initcall time, so
we are not allowed to call request_firmware earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently, in case of using scatter/gather mode, head of data is not sent to
destination. The cause is second descriptor address is set to NEXT.
The NEXT must have head of descriptor address.
This patch sets head of descriptor address to the NEXT.
Acked-by: Yong Wang <youg.y.wang@intel.com>
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
[dan.j.williams@intel.com: fixed up usage of virt_to_phys()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Current driver's device_prep_slave_sg can't be used by DMAC2 even
the sg list contains one item, this patch will enable DMAC2 to
use this API.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Rename intel_mid_dma_pci to intel_mid_dma_pci_driver to pick up the
applied annotations of that suffix.
Reported-by: <major_Lee@wistron.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently while submitting scatterlists with more than one SG
entry the DMA buffer address from the first SG entry is inserted
into all initialized DMA buffer descriptors. This is due to the
typo in the for_each_sg() loop where the scatterlist pointer is
used for obtaining the DMA buffer address and _not_ the SG list
iterator.
As a result all received data will be written only into the first
DMA buffer while reading. While writing the data from the first
DMA buffer is send to the device multiple times. This caused
the filesystem destruction on the MMC card when using DMA in
mxcmmc driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Changed Makefile to use <modules>-y instead of <modules>-objs. Following
(documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Expand the dma_mask of fsldma device to 36-bit, indicating that the
DMA engine can deal with 36-bit physical address and does not need
the SWIOTLB to create bounce buffer for it when doing dma_map_*().
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Use the ccflag-y flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should not call kfree(dma) in mid_setup_dma error path because
the memory is allocated in intel_mid_dma_probe and will be freed
in intel_mid_dma_probe error path if mid_setup_dma return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
otherwise, i will be -1 inside the latest iteration of the while loop.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Smatch complains because we dereference "mid" before checking it. It
turns out that "mid" is always a valid pointer here so we can just
remove the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Product codenames are OK, but once an actual product name is available,
it should be referenced as well.
http://ark.intel.com/chipset.aspx?familyID=52499
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
NULL-terminating pci_device_id in pch_dma.c and scx200_acb.c
for appying MODULE_DEVICE_TABLE (to publish modalias-es).
Signed-off-by: Dzianis Kahanovich <mahatma@eu.by>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
After moving the PL022 driver to subsys_initcall() due to the need
of having stuff like regulators on the other end of the SPI link,
I noticed that the COH901318 DMA engine will get probed before
the DMA engine, so move it to an arch_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
mxdmac->channel was unsigned, so check (imxdmac->channel < 0) for
failed imx_dma_request_by_prio() made no sence. Explicitly check
signed values.
Also, fix uninitialzed use of ret.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Simplify: ((a && b) || (!a && !b)) => (a == b)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A bool will suffice. The default is little endian.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Defaults are "basic mode" for physical channels, and "logical source
logical destination" for logical channels.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it logical by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it low priority by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since we want to reduce the amount of required channel
configuration and remove channel_type, don't depend on it
to indicate whether the configuration is valid.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Commit 0793448 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved. It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status(). The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware. The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.
iperf (before fix):
[SUM] 0.0-41.3 sec 364 MBytes 73.9 Mbits/sec
iperf (after fix):
[SUM] 0.0- 4.5 sec 499 MBytes 940 Mbits/sec
This is a regression starting with 2.6.35.
Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Richard Scobie <richard@sauce.co.nz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The majority of drivers in drivers/dma/ will never establish cross
channel operation chains and do not need the extra overhead in struct
dma_async_tx_descriptor. Make channel switching opt-in by default.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Ira Snyder <iws@ovro.caltech.edu>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This driver is currently implemented as a user to the old i.MX
DMA API. This allows us to convert each user of the old API to
the dmaengine API one by one. Once this is done the old DMA
driver can be merged into the i.MX dmaengine driver.
V2: remove some debug leftovers and unused variables
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In 2.6.36 kernel, dma slave control command was introduced,
this patch changes the intel-mid-dma driver to this
new kernel slave interface
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Moved the WARN_ON to BUG_ON, as WARN_ON if hit,
can cause null pointer derefrences
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For a very high speed DMA various periphral devices need
scatter-gather list support. The DMA hardware support link list items.
This list can be circular also (adding new flag DMA_PREP_CIRCULAR_LIST)
Right now this flag is in driver header and should be moved to
dmaengine header file eventually
Signed-off-by: Ramesh Babu K V <ramesh.b.k.v@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Allow DMAC2 to share interrupt since exclusive interrupt line
for mrst DMAC2 is not provided on other platforms.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
intel_mid_dma driver allows interrupt sharing. Thus it needs
to check whether IRQ source is the DMA controller and return
the appropriate IRQ return.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds runtime PM support in this dma driver
for 4 PCI Controllers
Whenever the driver is idle (no channels grabbed), it
can go to low power state
It also adds the PCI suspend and resume support
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove obsolete pre_transfer hook in stedma40_chan_cfg. The
intent of this hook is merely to handle burst size
compensation for ux500 variant MMCI. Remove obsolete stedma40_set_psize
since it is only called from pre_transfer. DMAEngine device_control
replaces the functionality of stedma40_set_psize.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Set burst for physical or logical channels respectively.
Convert the values in dma_cfg to dma reg bits
for physical or logical channels.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix some leaks of allocated descriptors in error paths.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix desc_get to alloc a descriptor from the cache if the ones in the
list are waiting for the ack. Also, memzero the descriptor when
allocated from the list to ensure all fields are cleared.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
clk_get returns an ERR_PTR.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The value in the array, not the index, specifies the channel to be
disabled.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the DMAEngine API has support for scatterlist to scatterlist
copy, implement support for the STE DMA40 DMA controller.
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Acked-by: Per Fridén <per.friden@stericsson.com>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the generic DMAEngine API has support for scatterlist to
scatterlist copying, the device_prep_slave_sg() portion of the
DMA_SLAVE API is no longer necessary and has been removed.
However, the device_control() portion of the DMA_SLAVE API is still
useful to control device specific parameters, such as externally
controlled DMA transfers and maximum burst length.
A special dma_ctrl_cmd has been added to enable externally controlled
DMA transfers. This is currently specific to the Freescale DMA
controller, but can easily be made generic when another user is found.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the DMAEngine API has support for scatterlist to scatterlist
copy, implement support for the Freescale DMA controller.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds support for scatterlist to scatterlist DMA transfers. A
similar interface is exposed by the fsldma driver (through the DMA_SLAVE
API) and by the ste_dma40 driver (through an exported function).
This patch paves the way for making this type of copy operation a part
of the generic DMAEngine API. Futher patches will add support in
individual drivers.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for the Freescale i.MX SDMA engine.
The SDMA engine is a scatter/gather DMA engine which is implemented
as a seperate coprocessor. SDMA needs its own firmware which is
requested using the standard request_firmware mechanism. The firmware
has different entry points for each peripheral type, so drivers
have to pass the peripheral type to the DMA engine which in turn
picks the correct firmware entry point from a table contained in
the firmware image itself.
The original Freescale code also supports support for transfering
data to the internal SRAM which needs different entry points to
the firmware. Support for this is currently not implemented. Also,
support for the ASRC (asymmetric sample rate converter) is skipped.
I took a very simple approach to implement dmaengine support. Only
a single descriptor is statically assigned to a each channel. This
means that transfers can't be queued up but only a single transfer
is in progress. This simplifies implementation a lot and is sufficient
for the usual device/memory transfers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Linus Walleij <linus.ml.walleij@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cyclic transfers are useful for audio where a single buffer divided
in periods has to be transfered endlessly until stopped. After being
prepared the transfer is started using the dma_async_descriptor->tx_submit
function. dma_async_descriptor->callback is called after each period.
The transfer is stopped using the DMA_TERMINATE_ALL callback.
While being used for cyclic transfers the channel cannot be used
for other transfer types.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This creates a DMAengine driver for the ARM PL080/PL081 PrimeCells
based on the implementation earlier submitted by Peter Pearse.
This is working like a charm for memcpy and slave DMA to the PL011
PrimeCell on the PB11MPCore.
This DMA controller is used in mostly unmodified form in the ARM
RealView and Versatile platforms, in the ST-Ericsson Nomadik, and
in the ST SPEAr platform.
It has been converted to use the header from the Samsung PL080
derivate instead of its own defintions. The Samsungs have a custom
driver in their mach-* folders though, atleast we can share the
register definitions.
Cc: Peter Pearse <peter.pearse@arm.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[GFP_KERNEL to GFP_NOWAIT in pl08x_prep_dma_memcpy]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).
Note that this issue can also be reproduced by using the DMA test
client.
On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Tested-by: Luc Saillard <luc@saillard.org>
Acked-by: saeed bishara <saeed.bishara@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
"param" can be NULL here, so only dereference it after the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no point in pausing what isn't running.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
LLI allocation is now done on job level instead of channel level.
Previously the maximum length of a linked job in hw on a logical
channel was 8, since the LLIs where evenly divided. Now only
executing jobs have allocated LLIs which increase the length to
a maximum of 64 links in HW.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The handling of pause detection was slightly incorrect.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch includes non functional code clean up changes,
file header updates and a few magic numbers got defined.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a new job is added on a physical channel that already has
a job, the new job is linked in hw to the old job instead of
queueing up the jobs.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Make sure to extract the revision field explicitly and document
what bits are being accessed here without magic numbers.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The callback got called even when it was not supposed to. Also
removed some not needed interrupt trigger on/off code.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch cleans up some code and removes a suspend request that was pointless
since the hw was never configured nor running when it was called.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Removes an unnecessary register read and a few lines of code.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A transfer that runs in the different direction on the same
channel will now be resumed when the other is suspend/stopped.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Added various configuration checks.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
atc_chain_complete shall be called with atchan->lock held
and bh disabled.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use {read|write}l instead of __raw_{read|write}l since PCH DMA
controller is PCI device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'cnt' is unsigned, so this code may become wrong in future as
dmatest_add_threads() can return error code:
cnt = dmatest_add_threads(dtc, DMA_MEMCPY);
thread_count += cnt > 0 ? cnt : 0;
^^^^^^^
Now it can return only -EINVAL if and only if second argument of
dmatest_add_threads() is not one of DMA_MEMCPY, DMA_XOR, DMA_PQ.
So, now it is not wrong but may become wrong in future.
The semantic patch that finds this problem (many false-positive results):
(http://coccinelle.lip6.fr/)
// <smpl>
@ r1 @
identifier f;
@@
int f(...) { ... }
@@
identifier r1.f;
type T;
unsigned T x;
@@
*x = f(...)
...
*x > 0
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On some platforms (MacPro3,1) the BIOS assigns the ioatdma device to the
incorrect iommu causing faults when the driver initializes. Add a quirk
to catch this misconfiguration and try falling back to untranslated
operation (which works in the MacPro3,1 case).
Assuming there are other platforms with misconfigured iommus teach the
ioatdma driver to treat initialization failures as non-fatal (just fail
the driver load and emit a warning instead of triggering a BUG_ON).
This can be classified as a boot regression since 2.6.32 on affected
platforms since the ioatdma module did not autoload prior to that
kernel.
Cc: <stable@kernel.org>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Chris Li <lkml@chrisli.org>
Tested-by: Chris Li <lkml@chrisli.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This extends the DMA engine driver for the COH 901 318 used in the
U300 platform with the generic runtime slave control command.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This extends the DMA engine driver for the DMA40 used in the
U8500 platform with the generic runtime slave configuration
interface.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom
This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.
This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs
This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion
Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert ppc4xx adma driver to use new node pointer location
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If td_desc is NULL, just skip both kfrees.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This silences a compile warning on 32 bit systems:
drivers/dma/timb_dma.c:203: warning: cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes sure the DMA40 driver will also work on the oldest
silicon revisions that have the on-chip memory on another location
in the DB8500 and also requires explicit suspend before starting
or resuming a logical channel.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[added parenthesis to the definition of U8500_DMA_LCPA_BASE_ED]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes it possible to disable physical channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes a bug when suspending channels: first make the checks,
then suspend the channel, not the other way around.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Switch to allocating LCLA in memory instead of having a fixed
address.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Correct bug that could cause paused channels to stop.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We don't want interrupts when the source is done, only when
the destination is done and everything is complete at the
recieveing end of a transfer.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid doing unnessecary suspend when modifying logical channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix up some locking issues found by enabling lock debugging.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Added checks to deny operating on none-allocated channels.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This cleans up some extra newlines, removes some code duplication
and moves the code to comply better with checkpatch.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Better error handling when channel allocation fails.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use kmem cache instead of own cache, reducing code duplication
and bug sources.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fixed typo and moved freeing of client owned desc to free_dma.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We only need to write the configuration to a physical channel if
it is free, else it is already written.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixed lli_max=1 issue in case of full lcla, currently this case
is not properly handled.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (25 commits)
sh: fix up sh7785lcr_32bit_defconfig.
arch/sh/lib/strlen.S: Checkpatch cleanup
sh: fix up sh7786 dmaengine build.
sh: guard cookie consistency across termination in the DMA driver
sh: prevent the DMA driver from unloading, while in use
sh: fix Oops in the serial SCI driver
sh: allow platforms to specify SD-card supported voltages
mmc: let MFD's provide supported Vdd card voltages to tmio_mmc
sh: disable SD-card write-protection detection on kfr2r09
mfd: pass platform flags down to the tmio_mmc driver
tmio: add a platform flag to disable card write-protection detection
sh: Add SDHI DMA support to migor
sh: Add SDHI DMA support to kfr2r09
sh: Add SDHI DMA support to ms7724se
sh: Add SDHI DMA support to ecovec
mmc: add DMA support to tmio_mmc driver, when used on SuperH
sh: prepare the SDHI MFD driver to pass DMA configuration to tmio_mmc.c
mmc: prepare tmio_mmc for passing of DMA configuration from the MFD cell
sh: add DMA slave definitions to sh7724
sh: add DMA slaves for two SDHI controllers to sh7722
...
Add DMA Engine API driver for the PL330 DMAC.
This driver is supposed to be reusable by various
platforms that have one or more PL330 DMACs.
Atm, DMA_SLAVE and DMA_MEMCPY capabilities have been
implemented.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
[dan.j.williams@intel.com: missing slab.h and ->device_control() fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If all descriptors on a channel are terminated or the channel is released,
update the completed cookie counter to match the last cookie. This prevents
inconsistency warning on resumed DMA operation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This prevents the driver from unloading, while it is in use. Unloading of the
driver, while its DMA channels are held, leads to a kernel Oops.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
sh: update defconfigs.
sh: Fix up the NUMA build for recent LMB changes.
sh64: provide a stub per_cpu_trap_init() definition.
sh: fix up CONFIG_KEXEC=n build.
sh: fixup the docbook paths for clock framework shuffling.
driver core: Early dev_name() depends on slab_is_available().
sh: simplify WARN usage in SH clock driver
sh: Check return value of clk_get on ms7724
sh: Check return value of clk_get on ecovec24
sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
sh: move sh clock.c contents to drivers/sh/clk.
sh: move sh asm/clock.h contents to linux/sh_clk.h V2
sh: remove unused clock lookup
sh: switch boards to clkdev
sh: switch sh4-202 to clkdev
sh: switch shx3 to clkdev
sh: switch sh7757 to clkdev
sh: switch sh7763 to clkdev
sh: switch sh7780 to clkdev
sh: switch sh7786 to clkdev
...
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.
[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Saves 24 bytes per descriptor (64-bit) when the channel-switching
capabilities of async_tx are not required.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix for allocation failure of logical channel when event line
happens to be number 0.
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Support determining whether a channel is paused or
not using the status function.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one
errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The member 'private' of 'struct dma_chan' is meant for passing
data between client and the controller driver.
The DMA client driver may point it to platform specific stuff after
acquiring the channel. So, it is the responsiblity of the same code
to reset it, if it must.
The DMA engine doesn't set it and hence, shouldn't reset it either.
This reseting of private by DMA Engine comes in the way of implementing
default channel settings during DMAC probe. That capability is useful
for not having the clients to always provide platform specific data,
like Rx/Tx FIFO addresses, which usually doesn't change across channel
requests.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'sh/for-2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: fix a number of Oopses and leaks in SH framebuffer driver
SH: fix error paths in DMA driver
sh: sh7751 pci controller io port fix
sh: Fix maximum number of SCIF ports in R2D defconfigs
SH: fix TS field shift calculation for DMA drivers
The memory for ioatdma_device structure is being allocated in
alloc_ioatdma()
Signed-off-by: Minskey Guo <chaohong_guo@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are cases where cacheline-unaligned raid operations can hang the
dma channel. Simply disable these operations by increasing the
alignment constraints published to async_tx. The raid456 driver always
issues page aligned requests, so the only in-kernel user of the ioatdma
driver that is affected by this change is dmatest.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use separate locks for the descriptor prep (producer) and descriptor
cleanup (consumer) paths. Allows the producer path to run concurrently
with the cleanup path. Inspired by Documentation/circular-buffer.txt.
Cc: David Howells <dhowells@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This enables autoloading of the TXx9 sound driver on RBTX4927.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
To: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1101/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If channel allocation is failing, mark the channel unused and give PM a chance
to power down the hardware.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Lists of DMA channels and slaves are not changed, make them constant. Besides,
SH7724 channel and slave configuration of both DMA controllers is identical,
remove the extra copy of the configuration data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a straightforward driver for the ST-Ericsson DMA40 DMA
controller found in U8500, implemented akin to the existing
COH 901 318 driver.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidh Kasagar <srinidhi.kasagar@stericsson.com>
Cc: STEricsson_nomadik_linux@list.st.com
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Convert the device_is_tx_complete() operation on the
DMA engine to a generic device_tx_status()operation which
can return three states, DMA_TX_RUNNING, DMA_TX_COMPLETE,
DMA_TX_PAUSED.
[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert the device_terminate_all() operation on the
DMA engine to a generic device_control() operation
which can now optionally support also pausing and
resuming DMA on a certain channel. Implemented for the
COH 901 318 DMAC as an example.
[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
An incremental patch which clarifies what the spinlock is used for
and fixes a compiler warning.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adds the support for the DMA engine withing the timberdale FPGA.
The DMA channels are strict device to host, or host to device
and can not be used for generic memcpy.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the function to get the number of bytes left in the
ongoing DMA transaction actually work: the old code did not take
neither lli:s nor queued jobs into account. Also fix a missing
spinlock while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes up the code with a lot of comments that make it readable,
rename things with opaque names like "data" into something more
appropriate, and remove some very confusing BUG() statements.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Create a common platform data header file for the
shdma dmaengine driver. This is done by moving
common structures from sh asm/dmaengine.h to
linux/sh_dma.h. DMA registers are also copied from
sh asm/dma-register.h to make the code architecture
independent.
The sh header file asm/dmaengine.h is still kept
with the slave id enum. This allows us to keep the
old processor specific code as is and slowly move
over to slave id enums in per-processor headers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move SHDMA_SLAVE_NUMBER from asm/dmaengine.h to
shdma.h. Set it to 256 to support a wide range
of processors. The amount of memory consumed by
this change is limited to 256 bits.
While at it, rename to SH_DMA_SLAVE_NUMBER to
match with the rest of the file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch replaces the sh_dmae_slave_chan_id enum
with an unsigned int. The purpose of this chainge is
to make it possible to separate the slave id enums
from the dmaengine header.
The slave id enums varies with processor model, so in
the future it makes sense to put these in the processor
specific headers together with the pinmux enums.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: Convert sh to use read/update_persistent_clock
sh: Move PMB debugfs entry initialization to later stage
sh: Fix up flush_cache_vmap() on SMP.
sh: fix up MMU reset with variable PMB mapping sizes.
sh: establish PMB mappings for NUMA nodes.
sh: check for existing mappings for bolted PMB entries.
sh: fixed virt/phys mapping helpers for PMB.
sh: make pmb iomapping configurable.
sh: reworked dynamic PMB mapping.
sh: Fix up cpumask_of_pcibus() for the NUMA build.
serial: sh-sci: Tidy up build warnings.
sh: Fix up ctrl_read/write stragglers in migor setup.
serial: sh-sci: Add DMA support.
dmaengine: shdma: extend .device_terminate_all() to record partial transfer
sh: merge sh7722 and sh7724 DMA register definitions
sh: activate runtime PM for dmaengine on sh7722 and sh7724
dmaengine: shdma: add runtime PM support.
dmaengine: shdma: separate DMA headers.
dmaengine: shdma: convert to platform device resources
dmaengine: shdma: fix DMA error handling.
...
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the calling convention of ->timer_fn() and ->cleanup_fn() are unified
across hardware versions we can drop parameters to ioat_init_channel() and
unify ioat_is_dma_complete() implementations.
Both ->timer_fn() and ->cleanup_fn() are modified to expect a struct
dma_chan pointer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The hardware automatically disables further interrupts after each event
until rearmed. This allows a delay to be injected between the occurence
of the interrupt and the running of the cleanup routine. The delay is
scaled by the descriptor backlog and then written to the INTRDELAY
register which specifies the number of microseconds to hold off
interrupt delivery after an interrupt event occurs. According to
powertop this reduces the interrupt rate from ~5000 intr/s to ~150
intr/s per without affecting throughput (simple dd to a raid6 array).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since ioat_cleanup_preamble() and the update of the last completed
descriptor are not synchronized there is a chance that two cleanup threads
can see descriptors to clean. If the first cleans up all pending
descriptors then the second will trigger the BUG_ON.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The pending == 2 case no longer exists in the driver so, we can use
ioat2_ring_pending() outside the lock to determine if there might be any
descriptors in the ring that the hardware has not seen.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We already disallow raid operations while DCA is globally enabled, so
having it locally enabled is a nop and confusing when reading the code.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the COH 901 318 respect the scatter offset field by using
the sg_phys() rather than the sg_dma_address() so we get a pointer
to the actual data we want to send rather than the beginning of the
buffer. Also initialize the lli:s a bit more thoroughly.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the COH 901 318 configure channel direction (to or from
device) dynamically, instead of being passed in from the platform
data. This was necessary in order to get the MMC/SD-card channel
bidirectional (all other channels on the U300 were either RX or
TX but this one was both). This also sets memcpy() alignent to
even 2^2 (32bit) boundaries, which makes the memcpy() stress tests
start working.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Russell King - ARM Linux