Add "xo" value which is tcxo clock to sdhci-msm
DT binding properties.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"support-highspeed" was the obsoleted property.
And "broken-cd" is not synopsys specific property.
It can be referred to mmc.txt binding Documentation.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "clock-freq-min-max" property was deprecated.
There is "max-frequency" property in drivers/mmc/core/host.c
"max-frequency" can be replaced with "clock-freq-min-max".
Minimum clock value might be set to 100K by default.
Then MMC core should try to find the correct value from 400K to 100K.
So it just needs to set Maximum clock value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
stop_cmdr should be set to values relevant to stop command.
It migth be assigned to values whatever there is mrq->stop or not.
Then it doesn't need to use dw_mci_prepare_command().
It's enough to use the prep_stop_abort for preparing stop command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If DW_MMC_CARD_NO_USE_HOLD isn't set, it's usesd by default.
Enve if SDMMC_CMD_USB_HOLD_REG is set in prepare_command(), but it
doesn't set in pre_stop_abort().
To maintain the consistency, add the checking condition for this.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no property "clock-freq-min-max", mmc->f_min should be set
to 400K by default. But Some SoC can be used 100K.
When 100K is used, MMC core will try to check from 400K to 100K.
Reported-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If display the debug message, this message should be spamming.
If flags is maintained the previous value, didn't display the debug
message.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Developer wants to see the real register value, not register offset.
This patch fixed to display the real value of register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trivial fix to spelling mistake "desciptor" to "descriptor" in
dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By moving the mmc_packed_init() and mmc_packed_clean() into the
only file in the kernel where they are used, we save two exported
functions and can staticize those to the block.c file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct mmc_blk_request contains an opaque void *data that
is actually only used to store a pointer to a per-request
struct mmc_blk_data. This is confusing, so rename the member
to blkdata and forward-declare the block.c local struct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of open coding the check for the same thing that
the helper checks: use the helper.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Request card detect and write protect gpios using the provided API
by mmc core.
If a gpio is provided for card detect, we don't need to poll.
So only use polling when a gpio is not provided.
Once all pdata users register the gpios using gpio descriptors,
we could remove the platform callbacks.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
Card detect and write protect are currently not working on a DT
boot, and the driver relies on polling to get the state
of the card. The current code depends on platform data callbacks
to register and get the state of the gpios.
mmc core provides a generic way to parse device tree configuration,
which will take care of registering the gpios for us, lets use it
so that we don't need to poll, and parse the same properties.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: David Lechner <david@lechnology.com>
We surely have SDIO support by now :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wbsd_request_dma() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We never set "ret" to RESULT_OK.
Fixes: 9f9c4180f8 ("mmc: mmc_test: add test for non-blocking transfers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The type of host->private is (unsigned long *). No cast is needed
to return an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add bytewise register accesses support for newer versions of IPROC
SDHCI controllers.
Previous sdhci-iproc versions of SDIO controllers
(such as Raspberry Pi and Cygnus) only allowed for 32-bit register
accesses.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
This includes adding support for the sampling clock controller (SCC).
Based on work by Ai Kyuse.
Cc: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs
An illegal sequence data error may occur if there is a CRC or stopbit
error, or underrun. In this case set data->error correctly.
This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is in preparation for restoring saved tuning parameters
when resuming the TMIO driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for r7s72100 SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In moving platforms from board files to DT, there still needs to be a way
to set the ocr_mask setting for the tmio driver during probe. Without this
setting, the probe will fail because the supported voltages are not known.
This patch will also traditional platform registration platforms to
migrate to DT.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.
Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.
In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.
To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.
An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.
The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.
I have tried to fix all instances properly and run some tests
on the result.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ecc_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This gen_err flag is only assigned 0 or 1 and treated as a bool,
so convert it to a bool.
Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci capabilities register can be incorrect. The sdhci-caps-mask
and sdhci-caps dt properties specify which bits of the register are
incorrect and what their values should be. This patch makes the sdhci
driver use those properties to correct the caps during
__sdhci_read_caps.
During __sdhci_read_caps
Use the sdhci-caps-mask property to turn off the incorrect bits of the
sdhci register after reading them.
Use the sdhci-caps to turn on bits after using sdhci-caps-mask to turn
off the incorrect ones.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some systems the sdhci capabilty register is incorrect for one
reason or another.
The sdhci-caps-mask property specifies which bits in the register
are incorrect and should be turned off before using sdhci-caps to turn
on bits.
The sdhci-caps property specifies which bits should be turned on.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.
Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.
Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.
Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.
Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.
Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for DMA slave map has been added to the s3c24xx-dma
controller in commit 34681d84a0
"dmaengine: s3c24xx: Add dma_slave_map for s3c2440 devices"
This patch converts the s3cmci driver to also use it, so we can
eventually get rid of the exported filter function once all
related DMA clients are updated.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_NO_PRESCAN_POWERUP was invented to avoid running the power up
sequence, mmc_power_up(), during ->probe() of the mmc host driver, but
instead defer this to the mmc detect work. This is especially useful for
those hosts that suffers from a long initialization time, as this time
would otherwise add up to the total boot time.
However, due to the introduction of runtime PM of mmc host devices in the
mmc core, this behaviour changed a bit. More precisely, it caused the mmc
core to runtime resume the host device during ->probe() of the host driver.
In cases like the rtsx_usb_sdmmc, runtime resuming the device may be costly
and thus affecting the total boot time.
To improve this behaviour when using MMC_CAP2_NO_PRESCAN_POWERUP, let's
postpone also calling mmc_power_off() when starting the host. This change
allows the mmc core to avoid runtime resuming the device, as it don't need
to claim the host for that execution path.
Cc: Ritesh Raj Sarraf <rrs@researchut.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now there are no variant drivers using dw_mci_suspend
and dw_mci_resume, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's migrate it to use runtime PM and remove the system
PM callback from this driver. With this patch, it could
handle system PM properly and could also use runtime PM
if we enable it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We could disable biu clk if gpio card detect available,
or it is a non-removable device.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ritesh Harjani